3. Front Fender
-
Upload
mario-ravr -
Category
Documents
-
view
225 -
download
0
Transcript of 3. Front Fender
-
8/10/2019 3. Front Fender
1/6
| P a g e
-
8/10/2019 3. Front Fender
2/6
2 | P a g e
Front Fender
Open a new part with model units set
to millimeters.
Go to: File > New > Part
Select the three planes in the feature tree
and make them visible by clicking on the
glasses.
Change the names of the planes
Double click on the Front Plane in the feature tree.
Change the name into: VERTICAL PLANE FRONT FENDER
Double click on the Top Plane in the feature tree.
Change the name into: CENTERPLANE FRONT FENDER
Double click on the Right Plane in the feature tree.
Change the name into: MIDPLANE FRONT FENDER
Select the VERTICAL PLANE FRONT FENDER and
create a sketch by clicking on the 2D Sketch
icon
Draw the sketch as shown in the picture.
Start with the vertical construction line
and circle.
Offset the vertical construction line
bi-directional by clicking on the offset icon.
Change into: 80 mm
Select the Bi-directional option.
Click OK
Draw the other lines as shown in the picture.
Trim all the lines you dont need.
Add all the dimensions and sketch relations.
-
8/10/2019 3. Front Fender
3/6
3 | P a g e
Create a revolve
Go to:Insert > Boss/Base > Revolve
Axis of revolution : Select the green construction
line as shown in the picture.
Change the color of the part:
Right click on the part > Body properties > Change color >
Select the color you like.
Click OK
Select the MIDPLANE FRONT FENDER and create the
sketch as shown in the picture
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Mid Plane
Change into: 200 mm
Click OK
-
8/10/2019 3. Front Fender
4/6
4 | P a g e
Select the CENTERPLANE FRONT FENDER
and create a new sketch
Draw a vertical construction line
starting at the origin.
Draw a spline and add
the right dimensions.
You could change the shape
of the spline by dragging at the
tangency arrow. Design a
curve you like.
Mirror this spline about the
vertical construction line in the
middle of the sketch.
Connect all the dimensions with the
origin.
Use the SolidWorksModel part as
reference file if the 2D sketch is unclear
to you (Extrude2, Sketch 3).
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Trough All
Ensure that the offset is directed to the revolve.
If not, click Reverse direction
Click OK
-
8/10/2019 3. Front Fender
5/6
5 | P a g e
Select the VERTICAL PLANE FRONTFENDER and create a new sketch
Draw a vertical construction line
starting at the origin.
Draw a spline and add the dimensions.
Mirror this spline about the
vertical construction line in the middle
of the sketch.
Connect all the dimensions with the
origin.
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Trough All
Ensure that the offset is directed to
the revolve.
If not, click Reverse direction
Click OK
-
8/10/2019 3. Front Fender
6/6
6 | P a g e
Create a surface fillet
Select the green surface as shown in the picture.
Go to: Insert > Features >
Fillet/Round > 6 mm
Click OK
Hide all planes and sketches except:
- VERTICAL PLANE FRONT FENDER
- MIDPLANE FRONT FENDER
-
CENTERPLANE FRONT FENDER
Save the file with the following name: Front Fender
Congratulations, you just finished the Front Fender!