2x18w Fluorescent Emergency...
17
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights ABN 74 166 824 906 Email: [email protected] Web: www.wbstech.com.au Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128 Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149 4 Foot Single 18watt LED Non Emergency Light MODEL: FP4F18LED FEATURES • White powder coated steel body. • Led technology with a long life over 50000 hours. • Large size connector, and easy to fit multiple cables. • Three years full warranty on the complete fitting. Specifications
Transcript of 2x18w Fluorescent Emergency...
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
4 Foot Single 18watt LED Non Emergency Light
MODEL: FP4F18LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
Specifications
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
Module Number Colour Watts Voltage
Colour temp
Avg Lamp hrs
Lumen Flux Height Width Length
RA
FP4F18LED White 18 240 5000k 50,000 1900Lm 91 122 1228 ≥80
INSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector. 5. Install cover plate on the batten body. 6. Refit the diffuser.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
1）Maintained Emergency light (Figure: 1) 2）Non-maintained emergency light (Figure: 2 and Figure: 3)
Figure: 1 Figure: 2 Figure: 3 Controlled by the lighting switch Non-maintained mode
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPEE
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
4 Foot twin 18watt LED Non Emergency Light
MODEL: FP36LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
Specifications
ref model Colour Watts Voltage Colour temp Avg Lamp hrs Lumen Flux Height Width Length
RA
FP36LED White 18 240 5000k 50,000 3500Lm 91 122 1228
≥80
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 3 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
NSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector. 5. Install cover plate on the batten body. 6. Refit the diffuser.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
1）Maintained Emergency light (Figure: 1) 2）Non-maintained emergency light (Figure: 2 and Figure: 3)
Figure: 1 Figure: 2 Figure: 3
Controlled by the lighting switch Non-maintained mode
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPEE
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
4 Foot twin 18watt LED Non Emergency Light
MODEL: FP36LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
Specifications
ref model Colour Watts Voltage Colour temp Avg Lamp hrs Lumen Flux Height Width Length
RA
FP36LED White 18 240 5000k 50,000 3500Lm 91 122 1228
≥80
INSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector. 5. Install cover plate on the batten body. 6. Refit the diffuser.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
1）Maintained Emergency light (Figure: 1) 2）Non-maintained emergency light (Figure: 2 and Figure: 3)
Figure: 1 Figure: 2 Figure: 3
Controlled by the lighting switch Non-maintained mode
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPEE
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
2 Foot twin 18 watt Non Emergency Light
Model: FP18LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
SPECIFICATIONS
Model number Colour Watts Voltage
Colour temp
Avg Lamp hrs
Lumen Flux output Height Width Length
RA
FP18LED White 18 240 5000k 50,000 1600Lm 91 122 1228
≥70
INSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
5. Install cover plate on the batten body. 6. Refit the diffuser.
Figure: 1 Figure: 2 Figure: 3 Controlled by the lighting switch Non-maintained mode
1）Maintained Emergency light (Figure: 1)
2）Non-maintained emergency light (Figure: 2 and Figure: 3)
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
4 Foot Single 18watt LED Non Emergency Light
MODEL: FP4F18LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
Specifications
Module Number Colour Watts Voltage
Colour temp
Avg Lamp hrs
Lumen Flux Height Width Length
RA
FP4F18LED White 18 240 5000k 50,000 1900Lm 91 122 1228 ≥80
INSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector. 5. Install cover plate on the batten body. 6. Refit the diffuser.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
1）Maintained Emergency light (Figure: 1) 2）Non-maintained emergency light (Figure: 2 and Figure: 3)
Figure: 1 Figure: 2 Figure: 3 Controlled by the lighting switch Non-maintained mode
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPEE
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
2 Foot twin 18 watt Non Emergency Light
Model: FP18LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
SPECIFICATIONS
Model number Colour Watts Voltage
Colour temp
Avg Lamp hrs
Lumen Flux output Height Width Length
RA
FP18LED White 18 240 5000k 50,000 1600Lm 91 122 1228
≥70
INSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
5. Install cover plate on the batten body. 6. Refit the diffuser.
Figure: 1 Figure: 2 Figure: 3 Controlled by the lighting switch Non-maintained mode
1）Maintained Emergency light (Figure: 1)
2）Non-maintained emergency light (Figure: 2 and Figure: 3)
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
2 Foot 9 watt Single LED Non Emergency Light
FP2F10LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
SPECIFICATIONS
Model number Colour Watts Voltage
Colour temp
Avg Lamp hrs
Lumen Flux output Height Width Length
RA
FP2F10LED White 9 240 5000k 50,000 950Lm 91 122 1228
≥70
INSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector. 5. Install cover plate on the batten body. 6. Refit the diffuser.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
1）Maintained Emergency light (Figure: 1)
2）Non-maintained emergency light (Figure: 2 and Figure: 3)
Figure: 1 Figure: 2 Figure: 3
Controlled by the lighting switch Non-maintained mode
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPEE
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 1 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
2 Foot 9 watt Single LED Non Emergency Light
FP2F10LED
FEATURES
• White powder coated steel body.
• Led technology with a long life over 50000 hours.
• Large size connector, and easy to fit multiple cables.
• Three years full warranty on the complete fitting.
WBS TECHNOLOGY Manufacturer of Emergency lights and LED lights
ABN 74 166 824 906 Email: [email protected]
Web: www.wbstech.com.au
Tel: 1300 WBS LED (927 533) Sydney office: Unit 32, 2 Slough Ave, Silverwater NSW 2128
Fax: 02 8580 4689 Page 2 Melbourne office: unit 66, 170 Forster Rd, Mt Waverley VIC 3149
SPECIFICATIONS
Model number Colour Watts Voltage
Colour temp
Vag Lamp hrs
Lumen Flux output Height Width Length
RA
FP2F10LED White 9 240 5000k 50,000 950Lm 91 122 1228
≥70
INSTALLATION
1. Remove the diffuser. 2. Separate cover plate from the batten body carefully. 3. Fix the batten body on the wall or on the ceiling. 4. Connect Mains cable to the 4 ports connector. 5. Install cover plate on the batten body. 6. Refit the diffuser.
Mark Description Building wiring cable
SA Switched Active Switch cable
N Neutral Neutral cable
E Earth Earth cable
1）Maintained Emergency light (Figure: 1)
2）Non-maintained emergency light (Figure: 2 and Figure: 3)
Figure: 1 Figure: 2 Figure: 3
Controlled by the lighting switch Non-maintained mode
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPEE
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
E
UA
N
SA
MAINS
CABLING
CABLE ENTRY
HOLE
TAPE
