2inc 602 Manifold

WELL TESTINGPRODUCTCATALOG

02/ 2007

Red Deer Ironworks Inc.6785 – 52nd Ave.

Red Deer, AB T4N 4K8Ph. 403.343.1141Fx. 403.343.3315

[email protected]

PART # IFTEE

2” FIG. 602 FRAC/ CUSHION TEE

Features and Benefits:

AISI 4130 is a higher-yield material than comparable (welded) tees. Allows greater wearability –min. wall thickness for 5000 PSI is 0.216” (per ASME B31.3) Min. wall for welded (A420 WPL6)material is 0.286”.

Thicker wall – 0.500” as compared to welded (0.344”). This equates to 0.284” wear/ corrosionallowance as compared to 0.058” for a welded assembly.

“SAFETY THREAD” connection – RDI’s Fig. 602 thread half (female sub) will not connect to aFig.1502 wing (male connection)

Smooth bore – no root weld intruding into the bore of the fitting.

Improved cushioning effect – cushion end of tee extended an additional 1.00” versus welded.Additional 0.500” of cushion cavity and additional 0.500” of steel on end.

Optional ½” NPT tap available on end of tee for sampling or pressure gauge.

AVAIL. SEP/06 – HSN seals will be standard on all RDI flowline equipment.

A

A

B

“A” DIMENSION: 6”“B” DIMENSION: 11.25”BORE: 1-5/8” (SAME AS S160 PIPE)

PRESSURE RATING: 5000 PSI SOUR

SHIPPING WT.: 30 LBS.

MATERIAL: AISI 4130 (TEE & NUT)

CONFORMS TO:API 6A, API 16C & NACE MR0175

ALL COMPONENTS FULLY TRACEABLE &SHIP W/ MTR’S & HYDRO-TEST REPORT

ALSO AVAIL: 1x1 1502, 2x1 1502 & 2x2 1502 PLUG VALVES.



[email protected]

PART # PV2602

2” FIG. 602 INTEGRAL PLUG VALVE


Valve bore matches the I.D. of all RDI 2” 602 integral fittings & 2” S160 welded flowline.

Valve is the same length as many competitor’s plug valves and is the same length as RDI’s 2” Fig.602 short pattern ball valve.

All valves hydro-tested (shell & seats) before shipping.

All valves meet API 6A, API 16C & NACE MR0175 requirements for sour service.

All valves come standard with giant button head grease fitting. Recommended grease – Desco 955stick grease (“J” or “K” stick).

Repair kits available from stock at RDI.



HSN seals are standard on all RDI flowline equipment and valves.

“A” DIMENSION: 9.75”

BORE: 1-5/8” (SAME AS S160 PIPE)


SHIPPING WT.: 45 LBS.

MATERIAL: API TRIM CLASS DD/TEMP CLASS L (SOUR/LO-TEMP)



A



[email protected]

PART # BV2602 & BV2602SP

2” FIG. 602 INTEGRAL BALL VALVE


AISI 4130 is a higher-yield material than comparable valves (A105N or A350 LF2 material).

Valve bore matches the I.D. of all RDI integral fittings & 2” S160 welded flowline.

Short pattern valve is the same length as many competitor’s plug valves and will be the samelength as RDI’s 2” Fig. 602 plug valve (avail. Sep. ’06).

All valves hydro-tested (shell & seats) before shipping.

All valves meet API 6A, API 16C & NACE MR0175 requirements for sour service.

All valves come standard with giant button head grease fitting. Recommended grease – Desco 622– Sour service/ low temp./ light viscosity.

Repair kits available from RDI (roughly ¼ the cost of a major plug valve kit).



All combinations of 2” Fig.602 & Fig.1502 Thread (female subs) & Wing (male sub) connectionavailable.

AVAIL. SEP/06 – HSN seals will be standard on all RDI flowline equipment and valves.

B

“A” DIMENSION: 12” (LONG PATTERN)“B” DIMENSION: 9.75” (SHORT PATTERN)



SHIPPING WT. : LONG – 37 LBS.SHORT – 35 LBS.

MATERIAL: AISI 4130 (BODY, SUBS &NUT)



A



[email protected]

2” FIG. 602 INTEGRAL BALL VLV MANIFOLD


The RDI ball valve manifold is a new concept in well testing manifolds. It combines the quality andwearability of more expensive plug valve manifolds with the economic advantages of ball valves(major repair kits sell for only $150.00).

Its’ compact size makes it an excellent option for crowded P-Tank installations.

Also available as a four-choke (douple pressure drop) configuration.

AISI 4130 is a higher-yield material than comparable (welded) components. Allows greaterwearability – min. wall thickness for 5000 PSI is 0.216” (per ASME B31.3) Min. wall for welded(A420 WPL6) material is 0.286”.





B

“A” DIMENSION: 32”“B” DIMENSION: 48”

PRESSURE RATING: 5000 PSISOUR

SHIPPING WT. 469 LBS.

MATERIAL: AISI 4130(ALL MAJORCOMPONENTS & NUTS)CONFORMS TO:API 6A, API 16C & NACEMR0175

ALL COMPONENTS FULLYTRACEABLE & SHIP W/ MTR’S& HYDRO-TEST REPORT

A

*** PLUG VALVE MANIFOLD AVAIL. OCT. ’06 !!! ***



[email protected]

2” FIG. 602 DUAL STAGE BALL VLV MANIFOLD


The RDI ball valve manifold is a new concept in well testing manifolds. It combines the quality andwearability of more expensive plug valve manifolds with the economic advantages of ball valves(major repair kits sell for only $150.00).

Its’ compact size makes it an excellent option for crowded P-Tank installations.

Shown above is the four-choke/ dual stage system. This allows two separate pressure controlpoints for high pressure/ flow rate wells with reduced washing and wear.

AISI 4130 is a higher-yield material than comparable (welded) components. Allows greaterwearability – min. wall thickness for 5000 PSI is 0.216” (per ASME B31.3) Min. wall for welded(A420 WPL6) material is 0.286”.





B

“A” DIMENSION: 32”“B” DIMENSION: 68”

PRESSURE RATING: 5000 PSISOUR

SHIPPING WT. 530 LBS.

MATERIAL: AISI 4130(ALL MAJORCOMPONENTS & NUTS)CONFORMS TO:API 6A, API 16C & NACEMR0175

ALL COMPONENTS FULLYTRACEABLE & SHIP W/ MTR’S& HYDRO-TEST REPORT

A

*** PLUG VALVE MANIFOLD AVAIL. OCT. ’06 !!! ***



[email protected]

PART # ICHOKE26L

2” FIG. 602 INTEGRAL CHOKE



This choke accepts standard Best-profile choke beans & topworks. Choke comes standard with ½”NPT tap on blanking cap.




Other Pup lengths are available from stock as welded components.


A

“A” DIMENSION: 6”“B” DIMENSION: 15.5”

PRESSURE RATING: 5000 PSI SOURSHIPPING WT. : 55 LBS.

**ACCEPTS STANDARD BEST-PROFILECHOKE BEANS & ADJUSTABLE TOPWORKS

MATERIAL: AISI 4130 (BODY, CAGENIPPLE & NUTS)



B



[email protected]

PART # ICR26MMMF & ICR26FFFM

2” FIG. 602 INTEGRAL CROSSES






Optional ½” NPT tap available in center of cross for sampling or pressure gauge.


B

“A” DIMENSION: 6” (LONG PATTERN)“B” DIMENSION: 12” (SHORT PATTERN)



SHIPPING WT. : MxMxMxF – 56 LBS.FxFxFxM – 40 LBS.

MATERIAL: AISI 4130 (CROSS & NUT)



A



[email protected]

PART # IT26MFM, IT26MFF

2” FIG. 602 INTEGRAL TEE


AISI 4130 is a higher-yield material than comparable (welded) tees. Allows greater corrosion/ wearallowance – min. wall thickness for 5000 PSI is 0.216” (per ASME B31.3) Min. wall for welded(A420 WPL6) material is 0.286”.





A

A

B

“A” DIMENSION: 6”“B” DIMENSION: 12”BORE: 1-5/8” (SAME AS S160 PIPE)


AVAIL. MxFxM or MxFxFSHIPPING WT.: 44 LBS. MxFxM

34 LBS. MxFxFMATERIAL: AISI 4130 (TEE & NUT)





[email protected]

PART # PUPX

2” FIG. 602 INTEGRAL PUPS






Other Pup lengths are available from stock as welded components.


A

“A” DIMENSION: 12” or 24”BORE: 1-5/8” (SAME AS S160 PIPE)


SHIPPING WT. : 1 FT. – 23 LBS.2 FT. – 35 LBS.

MATERIAL: AISI 4130 (BODY & NUT)





[email protected]

PART # XOXXXXX

INTEGRAL CROSS-OVERS


All combinations available from stock or with a short lead time – Union X Union, Union X NPT,Union x EUE, etc., etc.

Please contact the factory – RDI can produce virtually any crossover you require.

AISI 4130 is a higher-yield material than comparable (welded) crossovers which allows greaterwearability .


HSN seals are be standard on all RDI flowline equipment.

**ALL COMBINATIONS OF SIZES,CONNECTIONS & END-TO-END LGTHS.







[email protected]

PART # DATA

2” FIG. 602 DATA HEADER






Comes standard with one ¾” NPT tap on center and two ½” NPT taps on sides.

Other NPT tap sizes available on end request.


A

“A” DIMENSION: 24”BORE: 1-5/8” (SAME AS S160 PIPE)


SHIPPING WT. : 43 LBS.






[email protected]

PART # IR2426F, IR2426M

2” FIG. 602 FLANGE ADAPTORS



All RDI flange adaptors bear the API monogram.



All combinations of 2” Fig.602 & 2” Fig.1502 Thread (female subs) & Wing (male sub) connectionavailable.


A

“A” DIMENSION: 6”

FLANGE RATING: 2-1/16” 5000 PSI SOUR(R-24 CONNECTION)

SHIPPING WT. : R-24xF – 32 LBS.R-24xM – 35 LBS.

MATERIAL: AISI 4130 (FLANGE &NUT)



A



[email protected]

2” FIG. 602 “SAFETY THREAD”


Reduced outside diameter allows the 2” 1502 wing nut to slide over without thread engagement.

Threaded length increased 0.250” to compensate for reduced outside diameter. Increased threadengagement means a stronger connection.

Shoulder at base of thread prevents 2” 1502 wing from over-running or cross-threading to furtherreduce the chance of creating a possible pressure-tight seal.

While this connection greatly reduces the risk, RDI cannot anticipate every field installationsituation possible, and cannot warrant the connection as fail-safe.

Never use mis-matched parts – ie; different line sizes, pressure ratings or any other component (includingwingnuts, subs and segments).

Never use or substitute non-RDI components or parts in RDI products and assemblies. Never modify or alter RDI product (including welding) unless expressly approved by RDI. Never loosen a connection while under pressure. Never use worn or damaged products. Contact RDI for specific erosion and wear limits. Remove any product exhibiting signs of leakage from service immediately. Allows follow safe lifting, handling and storage procedures. Never exceed the rating working pressure of a part. Proper make-up is required to achieve rating working

pressures. Always ensure lines are drained completely before dis-assembly or work on the part. Take extra pre-

cautions when hazardous fluids or gases may be present. Always ensure the product is suited to the application. Never use standard service material in a sour

application or standard temp. product in a low temperature application. Always use appropriate safety and protective equipment.

IF IN DOUBT – CALL RDI @ (403) 343- 1141

THIS CONNECTION VIRTUALLYELIMINATES THE POSSIBILITY OF

MATING A2” 1502 MALE (WING)CONNECTION TO A

2” 602 FEMALE (THREAD)

2inc 602 Manifold

Documents

Transcript of 2inc 602 Manifold