Please read the following instructions and warningscarefully BEFORE assmebly and USE of the bassinet.

Tools required: Phillips head screwdriverand small adjustable wrench (not included).

Vibration & Sound Unit requires 3 "AA" batteries (not included).KEEP THIS INSTRUCTION MANUAL FOR FUTURE USE.Adult assembly required.For use with children from birth to 15 lbs.Keep small parts away from children.Fashions may vary.

26010

WARNING:Failure to follow these warnings and instructions could result in serious injury or death.FALL HAZARD:• To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached 15 lbs. whichever comes first.SUFFOCATION HAZARD: Infants can suffocate• In gaps between an extra pad and side of the bassinet• On soft bedding• NEVER add a mattress, pillow, comforter or padding. Use ONLY the pad provided by Summer Infant.• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.• NEVER move, lift or transport bassinet while child is in it.• ALWAYS lock casters when child is in bassinet.• ALWAYS ensure that the bassinet sleeping area is secure to base.• ALWAYS use on flat, stable surfaces• NEVER use near stairs.• Strings can cause strangulation! Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a bassinet or cradle or attach strings to toys.

Mother’s Touch®

Soothing BassinetINSTRUCTION MANUAL

2

BATTERY WARNING:• Do not mix old and new batteries.• Do not mix alkaline, standard, or rechargeable batteries.• Remove batteries when vibration & sound unit is stored for long periods of time or when batteries are exhausted.• Dispose of exhausted batteries properly.

components:

horizontal support barvibration & sound unit

screws (4)

metal rim

floorboard bassinet skirt

mattress pad and sheet canopy

basket (1)x-frame (2)

u-bar with casters (2)

toys (3)

to assemble bassinet storage baskets:

Step 1: Assemble basket to connectors by depressing spring pins and inserting basket frame ends until spring pins lock into place (Figure D).

Repeat on opposite side (Figure E).

A

B C

D

E

3

to assemble bassinet frame:

spring pin

Note: For Step 1, orient X-Frame with Horizontal Support Bar connectors facing inside of frame (Figure A).

Step 1: Slide one X-Frame onto U-Bar until spring pin locks in place (Figure A). Slide second X-Frame onto same U-Bar until spring pin locks in place. Repeat until both U-Bars are fully connected.

Step 2: Connect Horizontal Support Bar into frame (Figure B) until both spring pins (Figure C) lock in place.

horizontal support bar connector (facing inside of frame)

4

to assemble bassinet:Step 1: Place metal rim on floor so that metal arms are facing upwards (Figure F). Place floorboard inside metal rim so that snaps are facing down. Feed 2 metal support arms through slots on floorboard (Figure G). Pull back firmly and insert other 2 support arms.

Step 2: Slide bassinet skirt onto floorboard making sure to align bottom openings with predrilled holes on floorboard (Figure H).

Step 3: Flip bassinet floorboard/skirt assembly to upright position and place onto bassinet frame (Figure I).

Step 4: Align four alignment holes on bassinet’s floorboard with hollow pins on frame (Figure J).

F

G

H

I

J

alignment hole

screw hole

5

to assemble bassinet (continued):Step 5: Using the four screws provided, secure bassinet floorboard to the frame aligning holes (Figure K). Helpful Hint: Align holes and fasten one at a time.

Snap all snaps located on the inner skirt to the bassinet floorboard (Figure L)

Step 6: Insert sheeted mattress pad into Bassinet (Figure M). NOTE: Sheet flap should be on underside.

to attach canopy to bassinet:Step 7: Take canopy and place over bassinet. Position canopy so that it rests on the bassinet rim and clip canopy ends onto each side of bassinet. Note: For proper canopy placement, make sure to position clips in front of hook and loop. (Figure N.)Attach canopy to bassinet skirt by securing hook and loop fasteners to bassinet skirt in 3 places: on both sides and at end.

to attach toys:Step 8: Attach Toys to Canopy by feeding toy string through canopy loop and securing hook and loop fastener (Figure O). Repeat for other 2 toys.

Canopy set up and use:Possible entanglement injury. Keep out of baby’s reach. Remove canopy when baby begins to push up on hands and knees.

WARNING:

K L

M

N

O

clip

hook and loop

6

vibration & sound unit:

Step 1: Install batteries in the Vibrations & Sound Unit (requires 3 “AA” batteries, not included). Unlatch battery door using a Phillips head screwdriver. Insert 3 “AA” batteries making sure the + and – are facing the correct way. The battery compartment is engraved for clarity. Re-attach the battery door (Figure P).

Step 2: Install Vibration & Sound Unit onto Bassinet by snapping onto bassinet rim (Figure Q).

NOTE: To remove Vibration & Sound Unit, apply pressure and roll-off unit from bassinet ring (Figure R).

to use bassinet:canopyThe Canopy can be easily adjusted to be at desired position over baby. The toys are attached to the canopy by hook & loop straps.

vibration & sound unitSelect Vibration: Select the vibration mode by turning the dial on the unit. To shut-off, turn dial all away to the “0” position (Figure S).

select sound:There is a 4-position slide switch on the unit. Set the 4-position slide switch to hear music, nature or womb sounds (Figure T).

Position 1: womb sound Position 2: two nature sounds Position 3: three different melodies Position 4: “OFF” position

Press lower left button to adjust volume. (Figure U). Press lower right button to scroll through the various sounds. (Figure V). There are 4 volume settings: off, low, medium and high. Note: Melodies have an auto-shut off feature. Music will stop in approximately 5 minutes to conserve battery power. To restart music, slide button (Figure T) to “Off” position, then slide back to desired sound.

sound

4321

vibration

scroll sounds buttonvolume button

P

Q

R

S

T

U V

7

to clean:bassinet canopySurface wash, air dry.

bassinet skirtStep 1: Remove bassinet from frame by removing 4 screws, and slip off bassinet skirt.

Step 2: Hand wash in cold water. Do not bleach. Hang to dry. Use warm iron - low setting, if desired.

bassinet basketSurface wash, air dry.

mattress sheetStep 1: Remove mattress sheet from mattress pad.

Step 2: Machine wash in cold water. Do not bleach. Tumble dry low. Use warm iron - low setting, if desired.

mattress padSurface wash, air dry.

maintenance:Please check the following before each use: Make sure the screws that hold the frame together are tight and that none are missing.

to use bassinet (continued):castersTo prevent bassinet from rolling, press down on caster lock lever to lock (2 casters on same side of bassinet) (Figure W).

W

8

sound unit:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.

Caution: Changes and Modifications not expressly approved by Summer Infant, Inc. can void your authority to operate this equipment under Federal Communications Commissions rules.

Summer Infant Europe, LTD.Office Suite 6, Second Floor

Bournehall House, Bournehall RoadBushey, Hertfordshire WD23 3HP UK

+44 (0) 208 420 4429

Summer Infant, Inc.1275 Park East Drive

Woonsocket, RI 02895 USA

1-800-268-6237

© 2009 Summer Infant, Inc.Colors and styles may vary.

Please retain information for future reference.

MADE IN CHINA. 10/09