2.4GHz 2 Channel Radio Control System

Model: SR2S

www.absima.com

2.4GHz 2 Channel remote system

Model: SR2S

You also can contact our service center:

www.absima.com

2.4GHz 2 Channel remote system

Model: SR2S

3. The special symbols

Do not use this product in bad weather such as rainy or thunderingto assure the safety of you and others.

Before you use the product, please make sure the movement of serverare corresond with the direction of joystick. If inconsistent, please adjsutbefore use.

First switch on the radio (red light or flashing means low battery), finally connect the receiver.

The sequence to shut down is, first turn off the receiver power and then the transmitter power.

If the above operations are reverse, it might lead to uncontrolled movement and cause accidents.

4

2.4GHz 2 Channel remote system

Model: SR2S

5. Transmitter parameters

Channels: 2Frequency band: 2.4GHzPower resource: 1.5V*8 „AA“ batteryProgram type: AFHDSModulation type: GFSKRF power: <20 dbMStatic current: <250mASize: 189x97x218mmWeight: 575gColor: blackAntenna length: 26mm

Channel: 3Frequency band: 2.4GHzProgram type: AFHDSModulation type: GFSKFailsafe function: yesSize: 35x21x12mmWeight: 10gVoltage: 4,8V - 6,6V

6. Receiver parameters

2.4GHz 2 Channel remote system

Model: SR2S

7. Each part of the transmitter

Throttle/BrakeStick

Throttle/BrakeTrim

BIND knob

Steering stick

Steering trim

Power inidcatorlight

Power switch

Batterybox

Battery cover

5

6

2.4GHz 2 Channel remote system

Model: SR2S

8. Receiver and servo connection

Channel 1: Steering servoChannel 2: Speed controllerChannel 3: Battery connection for gas powered modelsBIND/VCC: BIND process

7

2.4GHz 2 Channel remote system

Model: SR2S

9. 2.4GHz Operation notesIt use digital transmission mode, and this prevent outside interference effectiveactive and passive.

9.01 Matching (code)

Our products are well matched in the factory, you don´t need to match by yourself. If youare going to match the receiver with another transmitter or you have to connect a newreceiver or transmitter, please follow the following steps:

1. Install the battery to the 2.4GHz transmitter and shut it down. 2. Insert the matching lines to the channel „BIND/VCC“ port of the receiver. 3. Switch on the ESC or connect a receiver battery to channel 3, at the same time the redLED is flashing and this means the receiver is in the BIND mode. 4. Press and hold the „BIND“ button on the transmitter and switch on the power supply. 5. Observe the LED on the receiver. If the LED stops flashing, the binding process wassuccessful. 6. Release the „BIND“ button on the transmitter and take out the matching line. 7. Install the servo for testing8. If the test fails, please repeat the action above.

BIND button

9.02 Switch on

1. Connect every servo.2. Switch on the transmitter.3. Switch on the ESC or power supply.4. Receiver LED light solid. 5. Finish and use.

2.4GHz 2 Channel remote system

Model: SR2S

8

Switch on

9.03 Switch off1. Cut off the ESC or receiver power supply.2. Cut off the transmitter power supply.

Switch off

2.4GHz 2 Channel remote system

Model: SR2S

9

10. Failsafe

Fail safe function – digital protection against radio interference. The safety electronic can detect reception of a “false” or incomplete radio signal. E.g. due to a low transmitter battery or environmental radio interference which reach the model, or if the model is out of the transmitter range. For protection against damage, servo switches to the brake position and the model stops.

Setup:1. Turn on the power of transmitter.2. Connect power supply to receiver; LED on receiver should be solid.3. Control the throttle trigger to make servo to “brake” or “stop” mode and remain for a while.

5. Setup is complete.

Testing:1. Turn on the power of transmitter.2. Connect power supply to receiver.

4. Servo which controlled by fail safe should go to brake modus automatically. 5. In case can be complete step by step with the above action, means setting is correct.

4. Press set up button on receiver. LED on receiver should flash. Should flash for 3 sec.

ABSIMA GMBHGIBITZENHOFSTRASSE 127AD- 90443 NUERNBERGGERMANY www.absima.com