BMW Motorrad

Workshop installationguide

BMW Motorrad Smartphone Cradle

Order No. 77 01 2 461 553 BMW Motorrad 03/2018

Before commencing work, you must read these installation instructions through carefully and make sureyou understand them fully.

We congratulate you on your choice of optional accessories from BMW Motorrad that will enable you to customiseyour motorcycle in accordance with your personal preferences.

Safety is invariably an essential prerequisite for extracting full benefit and enjoyment from new accessories. Some workcalls for special tools and possibly a thorough knowledge of motorcycle technology. If you are in doubt consult a spe-cialist workshop, preferably your authorised BMW Motorrad dealer.

Since we provide you with a multitude of accessories and optional equipment, we cannot cover all equipment specifica-tions in these installation instructions. Therefore we restrict ourselves to the basic version of the corresponding model.The removal and installation of other possibly installed accessories is described in the corresponding installation instruc-tions. Consult your authorised BMW Motorrad dealer if you no longer have access to the sets of instructions you need.

If you have questions concerning your motorcycle or any of the accessories from our range, your authorisedBMW Motorrad dealer will gladly provide advice and assistance.

We at BMW Motorrad hope you will enjoy riding your BMW and that all your journeys will be pleasant and safe.

The symbols used to draw attention to precautionary statements in this manual are as follows:

CAUTION WARNING DANGER ATTENTION

Low-risk hazard. Non-avoidance can lead toslight or moderate injury.

Medium-risk hazard. Non-avoidance can lead to fatalor severe injury.

High-risk hazard. Non-avoidance leads to fatalor severe injury.

Special notes and precau-tionary measures. Non-compliance can lead todamage to the vehicleor accessory and, con-sequently, to voiding of thewarranty.

NOTICE Tightening torque

Specific instructions onhow to operate, control,adjust or look after items ofequipment on the motor-cycle.

Screws, bolts and nuts aretightened in accordancewith the applicable DIN/ISO standards. Tighteningtorques that deviate fromthe standards are stated.Non-compliance can resultin damage to the vehicleor accessories or can en-danger the driver.

Start of the main activity End of the main activity

Start of the secondary activity End of the secondary activityInstruction End of validity designation CS (construction status),

OE (optional extra) or OA (optional accessory)

© 2018 Bayerische Motoren Werke Aktiengesellschaft80788 Munich, GermanyNot to be reproduced by any means whatsoever, wholly or in part, without the written permission of BMW Motorrad, After Sales.Printed in Germany.Subject to change without notice. Errors and omissions excepted.All rights reserved.

2 Order No. 77 01 2 461 553 03/2018

BMW Motorrad Smartphone Cradle

Requisite tools

Torx screwdriver set

Set of socket wrenches

Set of hexagon socket wrenches

Torque wrench

Delivery specification

Smartphone Cradle

Also required:

Holder

Fillister head screw M5 x 16 4 pieces

Spacing bushing 4 pieces

Washer 4 pieces

Also required:

Securing screw, M8 x 30 4 pieces

Lubricant

MP 3 paste 07 55 9 062 476

3 Order No. 77 01 2 461 553 03/2018

Also required:

Cable tie 2 pieces

Also required:

Rubber tensioning straps 2 pieces

General instructions

ATTENTIONVehicle not securely proppedRisk of damage to parts if vehicle topples

Prop the vehicle securely.

4 Order No. 77 01 2 461 553 03/2018

77 52 012 Installing Smartphone Cradle

Additional work: 46 52 510 Removing and installing the rear-wheel stand special tool (motorcycles without centre stand)

1Removing screws in left handlebar clampingblock

NOTICEIn order to retain the basic setting of the handlebars un-changed, always slacken only one side of the handlebarclamping block.

Remove screws (1) in left handlebar clamping block.

2Installing securing screws in left handlebarclamping block

Clean and lubricate the securing screws.

Lubricant

MP 3 paste 07 55 9 062 476

Screw in bolts (21) and (3) slightly.

Tighten front mounting bolt (2) first.

Tighten rear mounting bolt (3).

Tightening torques

Securing screw to handlebar clamping block

M8 x 30 - 10.9

Lubricate screw, Lubric-ant (MP 3 paste)

Tighteningsequence: inthe forwarddirection oftravel, tightenuntil seated

25 Nm

5 Order No. 77 01 2 461 553 03/2018

3Removing screws for right handlebar clamp-ing block

NOTICEIn order to retain the basic setting of the handlebars un-changed, always slacken only one side of the handlebarclamping block.

Remove screws (1) in the right handlebar clamping block.

4Installing securing screws in right handlebarclamping block

Clean and lubricate the securing screws.

Lubricant

MP 3 paste 07 55 9 062 476

Slightly screw in screws (2) and (3).

Tighten front mounting bolt (2) first.

Tighten rear mounting bolt (3).

Tightening torques

Securing screw to handlebar clamping block

M8 x 30 - 10.9

Lubricate screw, Lubric-ant (MP 3 paste)

Tighteningsequence: inthe forwarddirection oftravel, tightenuntil seated

25 Nm

6 Order No. 77 01 2 461 553 03/2018

5Securing holder on securing screws

Insert spacing bushings (1) into rubber grommets (2).

Install holder (3) with screws (4) and washers (5) onmounting bolts (6).

Tightening torques

Bracket to screws for handlebar clamp

M5 x 20, Replace screw

Thread-locking com-pound (mechanical)

5 Nm

6Smartphone Cradle Installation

Remove screws (1) and clamping block (2) with transverseaxis (3) from holder (4).

7 Order No. 77 01 2 461 553 03/2018

Remove nuts (1) and bolts (2).

Disconnect clamping block upper section (3) and -lowersection (4) and remove transverse axis (5) and keep themsafely aside (will be reused).

Position new clamping block lower section (1) and newclamping block upper section (2) centred at cross-mem-ber (3).

Position Smartphone Cradle (4) on the new clamping blockupper section (2).

Install Smartphone Cradle (4) with screws (5).

Tightening torques

Smartphone Cradle to bracket

M4 x 30 1.3 Nm

Insert mounting elements (1) with mounted SmartphoneCradle (2) into the holder (3).

Position Smartphone Cradle (2) and install it withscrews (4).

Tightening torques

Cross-member to upper section of bracket

M5 x 12 5 Nm

8 Order No. 77 01 2 461 553 03/2018

7Exposing optional accessories plug

Pull optional accessories connector (1) and pull off protect-ive cap (2).

8Routing connecting cable

WARNINGSteering angle constrained by routing of cables orBowden cables not in compliance with correct pro-cedure.Impairment of road safety.

Check the freedom of movement of the handlebars.

Guide down access line (1) along brake line and securewith cable strap (arrows) and rubber strap (2).

9 Order No. 77 01 2 461 553 03/2018

9Making connection to Smart Phone Cradle

Secure access line (1) with cable strap (arrow) to frontpanel carrier.

Push plug for Smartphone Cradle (3) onto the plug mount-ing and connect using optional accessories connector (4).

Place protective cap (5) on plug (6) for additional powersupply.

10Final check of work performed

Check the following:

The work as performed achieved the intended purpose.

All reservoirs and containers have been filled and all fluidsand lubricants are at their correct levels.

All threaded fasteners released beforehand have been cor-rectly retightened.

The fuel system is free of leaks.

The lights and signalling equipment are fully operationaland the vehicle is roadworthy.

The brake pads of the front and rear brakes are beddedagainst the brake discs.

Function test, engine start suppression

CheckSet kill switch to centred position.

Select neutral.

Switch on the ignition.

Neutral indicator light "N" lights up.

Select a gear.

Neutral indicator light "N" goes out.

Operate the starter switch.

Starter does not operate.

Extend the side stand.

Pull the clutch lever.

Operate the starter switch.

Starter does not operate.

Retract the side stand.

Operate the starter switch without releasing the clutchlever.

Starter operates.

10 Order No. 77 01 2 461 553 03/2018

ResultNot all test steps completed successfully.

MeasureCheck the appropriate parts with the BMW Motorrad dia-gnostic system.

Always comply with the regulations regarding approval in the country of use.

NOTICEFor vehicles registered in the Federal Republic of Germany:No entry in the vehicle registration papers is required.

11 Order No. 77 01 2 461 553 03/2018