8/2/2019 22491115 Programming Securikey Module

1/3

PROGRAMMING NEW or REPLACEMENT TRANSMITTERSTO THE SECURIKEY+ MODULEIMPORTANT NOTE: Once you enter the programmingmode, if 16 seconds elapsewith no activity on the system,the programmingmodewill beterminated.. This is indicatedby one soft chirp immediately followed by one loud chirp.If this happens, simply start over.

The SECURIKEY+ System should be disarmed before beginning! You can disarmby either pressing the unlock button on a transmitter that is already p r o g r a m m e d ~or by using the valet switch.STEP1

STARTWITH VALETSWITCH OFF

STEP2TURN IGNITION KEVTOON

STEP 3~ . ~ ' H ~.~ : ~ H .~ . . . . ~ ' 1 B E E P~ . , ~.: CHANNEL 1 MEMORY MEMORY MEMORY MEMORY

VALET SWITCHON HORNSOUNDS POSITION POSITION POSITION POSITIONTHEN OFF3 TIMES .. LOCK" #1 #2 #3 #4

Now press the LOCK button ( hold the button for 3 seconds until the horn sounds) on alltransmitters that you want to program ( up to 4 ), or continue on to the next step Remember,when you're programming more than one transmitter, press the lock button on the firsttransmitter until the horn sounds, then press the lock button on the second transmitter, etcNever activate two or more transmitters at the same time while in programming mode

STEP4t - . ~ ~ ; ; ~ ...~ 2 B E E P S CHANNEL 2 MEMORY MEMORY MEMORY MEMORY.. POSITION POSITION POSITION POSITION.. UNLOCK" #1 #2 #3 #4VALETSWITCH ON.THENOFF HORNSOUNDS

Now press the UNLOCK button ( holdthe button for 3 seconds until the horn sounds) on alltransmitters that you want to program ( up to 4 ), or continue on to the next step.PROGRAMMING CONTINUED ON PAGE 16

15

8/2/2019 22491115 Programming Securikey Module

2/3

.. STEP 6~ E ~ : " ~ . . . . ~ 3 B E E P S CHANNEL 3 MEMORY MEMORY MEMORY MEMORY.. POSITION POSITION POSITION POSITION.. TRUNK RELEASE .. #1 #2 #3 #4VALET SWITCH ON THEN OFF HORNSOUNDS

If the vehicle does not have the Trunk Release Upgrade Kit installed, proceed to step 6Ifthe Trunk Release Upgrade Kit is installed into the vehicle, press ttle Green button ( hold thebutton for 3 seconds until the horn sounds) on all transmitters that you want to program ( up to4) or continue on to the next step

STEP6~ . ~ . , . , ~ . . . . ~ 4 B E E P S CHANNEL. 4 MEMORY MEMORY MEMORY MEMORY': ': POSITION POSITION POSITION POSITION

.. HEADLIGHT" #1 #2 #3 #4VALETSWITCHON THEN OFF HORNSOUNDSI f there are no SECURIKEY+ upgrade kits ( IE: Trunk Release or Remote Starter) installedinto the vehicle, press the Green button ( hold the button for 3 seconds until the horn sounds)on all transmitters that you want to program ( up to 4 ), Dr continue on to the next step

STEP7~ 1 ~ + . . . . ~ 6 B E E P S CHANNEL 5 MEMORY MEMORY MEMORY MEMORYPOSITION POSITION POSITION POSITION.. DEDICATED PAN IC .. #1 #2 #3 #4VALET SWITCHON THEN OFF HORNSOUNDS

Do not program transmitter buttons to this channel. On the SECURIKEY+, the panic featureactivates from the Lock button Continue on to the next stepSTEPS

~ i 9 i ; J ~ . ; ~ . . . . ~ 6 B E E P S CHANNEL 6 MEMORY MEMORY MEMORY MEMORY... POSITION POSITION POSITION POSITION" REMOTE START .. #1 #2 #3 #4VALET SWITCH ON THEN OFF HORN SOUNDSIf the Remote Start Upgrade Kit is installed into the vehicle, press the Green button ( hold thebutton for 3 seconds until the horn sounds) on all transmitters nlat you want to program ( up to4 ), or continue on to the next step

STEPSO F F ~

TURNIGNlTJON KEYTOOFF

SOFT&. . . . ::::::- LOUD BEEPHORN SOUNDS

PROGRAMMINGMODETERMINATED

WHAT IS CODE HOPPING?Each time a button on the SECURIKEY+ transmitter Is activated, the code for that transmitter changes or " advances" EaCh time thereceiver module receives a code from a SECURIKEY+ transmitter, the receiver advances and is now waiting for the next code in thesequenc;;eWhen a SECURIKEY+ transmitter is activated continuously while out of range of the receiver module, the transmitter code will advancebut the receiver code will not. When this happens, the transmitter and receiver become" mis - aligned ", and will no longer operate,To re - align the transmitter to the receiver, simply press and release the UNLOCK button on the transmitter tvvo times within one second

16

8/2/2019 22491115 Programming Securikey Module

3/3

PROGRAMMING THE SELECTABLE FEATURESThe SECURIKEY+ system offerSl\ number of selectable features that can be changed, allowing you to custom tit thesystemto your customer. The following Isa list of thefeatures that are selectable and can be changed using the valet s w ~ c h and any transmitter Ihat is programmed to the system installed In the vehicle.

FEATURE # FUNCTION 1 CHIRP 2 CHIRPS1 Headlights on for 20 seconds during disarm ON or OFF'2 Headlights on for 20 seconds during arm ON or OFF:3 Automatic ignition controlled door lock ON Or OFF4 Automatic ignition controlled door unlock ON or OFF5 Auto unlock driver's door only or al doors Driver's Door or All Doors6 Active or Passive arming Passive or Active7 Active or Passive door locks Passive or Active8 Trunk release output - 1 second or latched 1 Second or Latched9 Panic on lock bullon or option button Option or Lock10 Trunk Release hold 1 second or 2 presses Hold 1 Sec or 2 TImes

To change the seleclion of any of these features, follow the step by step programming procedures, and do not allowmore than 15 seconds to pass between any two steps or thesystem willterminate the programming mode. There is no need to complete the entire programming sequence After the appropriate features have been changed simplytum theignition key off to terminate the programming mode1 Be sure that the SECURIKEY+ system Is disarmed, and theUghted valet switch Is in the of f ( out) position before you begin2 Tum the vehicle's ignit ion key to the on p o s ~ i o n3 Press then release the L.E D valet switch 6 limes4 Immedialely turn the ignition key off Ihen back on

FEATURE 1 LED Flashes 1 TIme1 Chirp =Headlights ON During Disarm Horn Chirps either 1 or 2 TImes2 Chirps = HeadlightsOFF During DisarmTo change the selection press and release the lock button on the transmitter, which will be indicated by the appropriate 1 or 2 chirp signal from the hom If you do not want 10change Ihisfeature simply press and release the LED valet switch 2 times to advance to programmable feature number 2

FEATURE 2 LED Flashes 2 limes1 Chirp = Headlights ON During Arm Horn Chirps either 1 or 2 TImes2 Chirps = Headlights OFF DUring ArmTo change the selection, press and release the lock bulton on the transmitter, which will be indicated by the appropriate 1 or 2 chirp signal from the hom If you do not want tochange this feature simply press and release the LE O .. valetswilch 2 times to advance to programmable feature number :3.

FEATURES LED Flashes 3 TImes1 ChIrp = I g n ~ i o n controlled door locks ON HQrn Chirps either 1 or Z TImes2 Chirps = Ignition controlled doorlocks OFFTo change the selection, press and release thelock bullon on the transmiller, which will be Indicated by t h appropriate 1 or 2 chirp signal from the hom If you do not want tochange this feature, simplypress and release the L.E 0 valet switch 2 times to advance to programmable feature number 4

FEATURE 4 LEO Flashes 4 TImes1 Chirp = Ignition controlled unlock ON Hom Chirps either 1 or 2 limes2 Chirps = i g n ~ i o n controlled unlock OFF

To change the selection, press the lock button on the transmitter which will be indicated by the appropriate 1 or 2 chirp signal from the horn If you do not want to change thisfeature simply press and release the L E.D valetswitch Ztimes to advance to programmable feature number 5

FEATURES LED Flashes 5 TImes1 Chirp = Ignition controlled unlock DRIVER S DOOR Hom Chirps either 1 or 2 TImes2 Chirps = Ignitioncontrolled unlockALL DOORS

To change the selection press the lock button on the transmiller, which will be Indicated by the appropriate 1 or 2 chirp signal from the horn If you do not want to changeth isfeature simply press and release the LE D valet switch 2 times to advance to programmable feature number 6

FEATURE 6 LED Rashes 6 TImes1 Chirp = PASSIVE ARMING (Automatic Arming) Hom Chirps either 1 or 2 limes2 Chirps = ACTIVE ARMING (Arm by Remote Only)To change the selEtction, prEtss the lock button on the t r a n s m ~ t e r , which will be indicated by the appropriate 1 or 2 chirp signel from the horn If you do not want to change thisfeature, simplypress and release the L.E D vaiet switch 2 times to advance to programmable feature number 7

FEATURE 7 LED Flashes 7 TImes1 Chirp = PASSIVE DOOR LOCKS Horn Chirps either 1 or 2 TImes2 Chirps = ACTIVE DOOR LOCKSTo change the selection press the lock button on the transmitter, Which will be indicated by the appropriate 1 or 2 chirp signal from the horn. If you donot want to change thisfealure, simply press and release the L ED valet switch 2 times to advance to programmable feature numbere

FEATURE 8 Do not chenge this feature selection. It should be leflln the factory preset (1 chirp) mode Press and release the LED valet switch 2times to advance to programmable feature number 9FEATURE 9 LED Flashes 9 TImes1 Chirp = Remote Panic I GREENtransmitter button Horn Chirps either 1 or 2 TImes2 Chirps'" Remote Panic I LOCK transmitter bullon

To change the selection press the lock bullon on the transmitter, which will be indicated by the appropriate 1 or 2 chirp signal from the horn If you donot want to c h a ~ g e this.fealure simply press and rEtlease the LED valet s w ~ c h 2 times to advance to programmable featurenumber10

FEATURE 10 LED Flashes 10 TImes1 Chirp =Trunk Release HOLD GREEN BUTTON 1 SECOND Hom Chirps either 1 or2 limes2 Chirps = Trunk Release PRESS GREEN BUTTON2 TIMESTo change the selection press the lock bul ton on the transmitter, which will be indicated by the appropriate 1 or 2 chirp signal from Ihe horn If you do not want to change thisfeature simply pressandrelease the L E.D valet switch 2 t imes to exit the programming mode

17