22. Install the left fog light to the front bumper with three self-tapping screws. 23. Install the...

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2015 American Honda Motor Co., Inc. – All Rights Re

VERSION 1

www.collegehillshonda.com
FOG LIGHTS
served. AII02278-08 (151

2016 CIVIC2- AND 4-DOOR

0) 0

Issue Date

OCT 2015

PARTS LIST

Fog Light KitP/N 08V31-TBA-100AP/N 08V31-TBA-100BP/N 08V31-TBA-100C

Right fog light

Left fog light

Right fog light trim(May not be used)

Left fog light trim(May not be used)

Fog light harness

Relay harness

Combination light switch

Fuse label

Wire tie with clip(May not be used)

Relay

14 Wire ties(Some may not be used)

1 of 248V31-TBA-1000-90

7 Long wire ties(Some may not be used)
6 Self-tapping screws

20 A Fuse

Wire tie with holder

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

Diagonal cutters

10 mm Socket

Isopropyl alcohol

Shop towel

Tape

Ruler

Scissors

10 mm Open-end wrench

Ratchet

Blanket

5 mm Hex wrench

The following tool is available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.

Plastic Trim Tool (T/N SILTRIMTL10)

2 of 24 AII02278-0

Illustration of the Fog Lights Installed in the Vehicle

INSTALLATION

1. Disconnect the negative cable from the battery.

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

COMBINATION LIGHT SWITCH

20 A FUSE

RELAYHARNESS

LEFT FOG LIGHT

FOG LIGHT HARNESS

RIGHT FOG LIGHT

8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.

2. Remove the driver’s dashboard lower cover and
unplug the vehicle connectors and aspirator hose.

3. Remove the driver’s front door sill trim.

2 CLIPS

5 CLIPS

VEHICLECONNECTORS

ASPIRATOR HOSEVEHICLECONNECTOR

DRIVER’SDASHBOARDLOWER COVER

2 CLIPS

DRIVER’S FRONTDOOR SILL TRIM

3 CLIPS

4 RETAININGTABS

© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0

4. Pull away the door opening seal and remove the driver’s kick panel.

5. Lower the steering wheel. Apply the tape to the upper column cover as shown.

DOOR OPENING SEAL(Pull away.)

2 CLIPSDRIVER’SKICK PANEL

STEERINGWHEEL

UPPER COLUMNCOVER

TAPE

8 (1510) 3 of 24

6. If necessary, connect the negative cable to the
battery, set the power mode to ON. Turn the steering wheel 90° clockwise. Using a plastic trim tool, release the hooks.

7. Turn the steering wheel 180° counterclockwise. Using a plastic trim tool, release the hooks.

UPPER COLUMNCOVER

2 HOOKS PLASTICTRIM TOOL

UPPER COLUMNCOVER

2 HOOKSPLASTICTRIM TOOL

4 of 24 AII02278-0

8. Release the upper column cover and secure the upper column cover to the dashboard with tape.

9. Remove one self-tapping screw from the lower column cover.

TAPE

2 RETAININGTABS

UPPER COLUMNCOVER DASHBOARD

SELF-TAPPINGSCREW

LOWER COLUMNCOVER


10. Turn the steering wheel 180° clockwise and remove
one self-tapping screw from the lower column cover.

11. If necessary, set the power mode to OFF, then disconnect the negative cable from the battery.

12. Remove the lower column cover.

SELF-TAPPING SCREWLOWER COLUMN

COVER

SELF-TAPPING SCREW

LOWER COLUMNCOVER


13. Remove the front bumper:

• Apply tape to the areas shown on each side.

• Wrap a shop towel around the hood latch.

• Remove the front bulkhead cover.

TAPE FRONT BUMPER

HEADLIGHT

HOOD LATCH(Wrap with a shop towel.)

FRONT FENDER

8 CLIPSFRONT BULKHEADCOVER

8 (1510) 5 of 24

• Remove the four self-tapping screws, two bolts,
two hex bolts, and seven clips.

• With the help of an assistant, release seven retaining tabs on each side.NOTE: Remove the retaining tabs from the outside in the order shown. Make sure to remove the retaining tabs in the correct orientation.

4 SELF-TAPPINGSCREWS

7 CLIPS 2 HEXBOLTS

2 BOLTS

7 CLIPS

2 HEX BOLTS

BOLT

BOTTOM VIEWBOLT

FRONTBUMPER

3 RETAINING TABS

2

4 RETAINING TABS

1

FRONTBUMPER

Pull.

6 of 24 AII02278-0

• Remove the three clips.

• With the help of an assistant, remove the front bumper. Place the front bumper on a blanket to prevent damage.

3 CLIPS

FRONT BUMPER

4 RETAINING TABS

FRONT BUMPER


14. Remove the eight clips from the right front inner
fender and pull back the inner fender as shown.

15. Remove eight clips from the left front inner fender and pull back the inner fender as shown.

8 CLIPSFRONT RIGHT TIRE

RIGHT FRONT INNER FENDER(Pull back.)

8 CLIPS

FRONT LEFT TIRE

LEFT FRONT INNER FENDER(Pull back.)


Installing the Fog Lights

16. Remove four self-tapping screws from the front bumper.

If the vehicle is equipped with a left cap, continue with step 17; otherwise, go to step 21.

With Left Cap

17. Remove the left cover from the front bumper.

FRONT BUMPER(inside)

4 SELF-TAPPING SCREWS

7 RETAINING TABS


LEFT COVER

LEFT CAP

8 (1510) 7 of 24

18. Remove the left cap from the front bumper.
19. Install the left fog light on the bumper with three self-tapping screws.

FRONT BUMPER (outside)

LEFT CAP(Discard.)2 SELF-TAPPING

SCREWS(Discard.)

3 SELF-TAPPING SCREWS(supplied)


LEFT FOG LIGHT

8 of 24 AII02278-0

20. Install the left cover to the front bumper. Go to step 24.

Without Left Cap

21. Remove the left cover from the front bumper.

FRONT BUMPER

LEFT COVER(reused)

7 RETAINING TABS

7 RETAINING TABS


LEFT COVER(Discard.)


22. Install the left fog light to the front bumper with
three self-tapping screws.

23. Install the left fog light trim.

3 SELF-TAPPING SCREWS(supplied)


LEFT FOG LIGHT

FRONT BUMPERLEFT FOG LIGHT

TRIM

7 RETAINING TABS


24. Install the left cover or left fog light with four self-tapping screws.

25. Repeat steps 16 through 24 to install the right fog light to the right side of the front bumper.

Routing the Fog Light Harness

26. Remove three bolts, and move the washer tank aside.


4 SELF-TAPPING SCREWS (reused)

WASHER TANK

3 BOLTS

HOOK

8 (1510) 9 of 24

27. Route the fog light harness as shown. Remove the
tape from the vehicle 1-pin connector and plug the vehicle 1-pin connector into the fog light harness1-pin connector.

With 2.0L Engine

VEHICLE 1-PIN CONNECTOR

FOG LIGHT HARNESS 1-PIN CONNECTOR

FOG LIGHT HARNESS

RIGHT FRONT INNER FENDER

TAPE(Remove.)

10 of 24 AII02278-0

With 1.5L Engine

28. Install the washer tank.

29. Align the green tape on the fog light harness with the washer tank as shown and secure the fog light harness to the vehicle harness with one wire tie.


FOG LIGHT HARNESS 1-PIN CONNECTOR

FOG LIGHT HARNESS

RIGHT FRONT INNER FENDER

TAPE(Remove.)

WIRE TIE

WASHER TANK

FOG LIGHT HARNESS

VEHICLE HARNESS

GREEN TAPE

Align.


30. Secure the 1-pin connectors and fog light harness to
the vehicle harness with three wire ties.

31. Check the front bumper beam.

VEHICLE HARNESS

FOG LIGHT HARNESS

WIRE TIE

FOG LIGHT HARNESS

VEHICLE HARNESS

VEHICLE PANEL

WIRE TIE 1-PIN CONNECTORS

SECTION VIEW

2 WIRE TIES

FRONT BUMPER BEAMTYPE A

FRONT BUMPER BEAMTYPE B


If the vehicle is equipped with the front bumper beam type A, continue with step 32, otherwise, go to step 38.

With Front Bumper Beam Type A

32. Route the fog light harness along the front bumper beam as shown.

33. Secure the three clips on the left fog light harness to the vehicle panel as shown.

FOG LIGHT HARNESS

FRONT BUMPER BEAM

LEFT HEADLIGHT

3 CLIPS

VEHICLE PANEL

8 (1510) 11 of 24

34. Secure the three clips on the right fog light harness
to the vehicle panel as shown.

35. Secure the fog light harness to the front bumper beam with three long wire ties.

RIGHT HEADLIGHT

3 CLIPS

VEHICLE PANEL

3 LONG WIRE TIES

FRONT BUMPER BEAM FOG LIGHT

HARNESS

12 of 24 AII02278-0

36. Join four long wire ties together as shown and secure the fog light harness to the front bumper beam with two joined long wire ties.

FOG LIGHT HARNESS

2 JOINED LONG WIRE TIES

FRONT BUMPER BEAM

2 LONG WIRE TIES(Joined.)

2 JOINED LONG WIRE TIES

SECTION VIEW

FRONT BUMPER BEAM

FRONT


37. Secure the fog light harness to the vehicle harness
with one wire tie. Go to step 43.

With Front Bumper Beam Type B

38. Route the fog light harness along the front bumper beam as shown.

FRONT BUMPER BEAM

FOG LIGHT HARNESS

VEHICLE HARNESS

VEHICLE CLIP

WIRE TIE

FOG LIGHT HARNESS

VEHICLE PANEL

FRONT BUMPER BEAM


39. Secure the three clips on the fog light harness to the vehicle panel as shown.

LEFT HEADLIGHT

3 CLIPS

VEHICLE PANEL

8 (1510) 13 of 24

40. Secure three clips on the fog light harness to the
vehicle panel as shown.

41. Secure the fog light harness to the front bumper beam with five long wire ties.

RIGHT HEADLIGHT

3 CLIPS

VEHICLE PANEL

FOG LIGHT HARNESS

SECTION VIEW

FRONT BUMPER BEAM

FOG LIGHT HARNESS FRONT

BUMPER BEAM

5 LONG WIRE TIES

FRONT

14 of 24 AII02278-0

42. Secure the fog light harness to the vehicle harness with one wire tie.

If the vehicle is equipped with a 2.0L engine, continue with step 43; otherwise, go to step 45.

With 2.0L Engine

43. Install one wire tie with clip to green tape on the fog light harness, and secure the fog light harness to the resonator.

FRONT BUMPER BEAM FOG LIGHT

HARNESSVEHICLE HARNESS VEHICLE

CLIP

WIRE TIE

RESONATOR

FOG LIGHT HARNESS

WIRE TIE WITH CLIP

WIRE TIE WITH CLIP

GREEN TAPE


44. Align the branch of the fog light harness with the
vehicle clip and secure the fog light harness to the vehicle harness with one wire tie. Go to step 46.

With 1.5L Engine

45. Align the branch of the fog light harness with the vehicle clip and secure the fog light harness to the vehicle harness with one wire tie.

VEHICLE CLIP

VEHICLE HARNESS

FOG LIGHT HARNESS

BRANCHES

WIRE TIE

VEHICLE CLIP

VEHICLE HARNESS

FOG LIGHT HARNESS

BRANCHES

WIRE TIE


46. Remove the vehicle ground bolt. Attach the two fog light harness ground terminals to the vehicle ground terminal and install the vehicle ground bolt.NOTE: Do not put the ground terminal calkings on top of one another.

47. Secure the fog light harness to the vehicle harness with one wire tie.

LEFT FRONT INNER FENDER

VEHICLE GROUND BOLT(reused)

VEHICLE GROUND TERMINAL

2 FOG LIGHT HARNESS GROUND TERMINALS

VEHICLE HARNESS

VEHICLE CLIP

WIRE TIEFOG LIGHT HARNESS

8 (1510) 15 of 24

48. Plug the two fog light harness 2-pin connectors into
each fog light, and with the help of an assistant, install the front bumper.

Routing the Relay Harness

49. Install the relay into the relay harness relay block.

FRONT BUMPER LEFT FOG LIGHT

RIGHT FOG LIGHT

FOG LIGHT HARNESS 2-PIN CONNECTORS

RELAY

RELAY HARNESS RELAY BLOCK

16 of 24 AII02278-0

If the vehicle is equipped with CVT, continue with step 50; otherwise, go to step 51.

With CVT

50. Plug the relay harness 1-pin connector into the vehicle 1-pin connector. Go to step 52.

With M/T

51. Remove the tape from the vehicle 1-pin connector and plug the relay harness 1-pin connector into the vehicle 1-pin connector.


RELAY HARNESS 1-PIN CONNECTOR

RELAY HARNESS

FUSE BOX



RELAY HARNESS

FUSE BOXTAPE(Remove.)


52. Route the switch harness as shown. Attach the wire
tie with holder to the relay harness relay block and secure it to the vehicle harness with the wire tie with holder.

VEHICLE HARNESS

RELAY HARNESS RELAY BLOCK

WIRE TIE WITH HOLDER

VEHICLE CLIP


If the vehicle is without another accessory harness 4-pin connector, continue with step 54; otherwise, go to step 53.

Without Another Accessory Harness 4-Pin Connector

53. Plug the relay harness 4-pin connector into the fuse box. Go to step 55.

FRONT VIEW

Plug in here.

FUSE BOX


8 (1510) 17 of 24

With Another Accessory Harness 4-Pin Connector
54. Remove and discard the dummy connector from the other accessory harness 4-pin connector and plug the relay harness 4-pin connector into the other accessory harness 4-pin connector.


FUSE BOX

FRONT VIEWDUMMY CONNECTOR(Discard.)

OTHER ACCESSORY HARNESS 4-PIN CONNECTORS

OTHER ACCESSORY HARNESS 4-PIN CONNECTOR

18 of 24 AII02278-0

If the vehicle is equipped with a remote control engine starter and/or wireless charger harness 6-pin connector go to step 56; otherwise continue with step 55.

Without Another Accessory Harness 6-pin Connector

55. Plug the relay harness 6-pin connector into the fuse box. Go to step 57.


FUSE BOX

FRONT VIEW

Plug in here.


With Remote Control Engine Starter and/or Wireless Charger Harness 6-Pin Connector
56. If the remote control engine starter and/or wireless charger harness 6-pin connector is plugged into the vehicle 6-pin connector, plug the relay harness 6-pin connector into the remote control engine starter and/or wireless charger harness 6-pin connector.

FUSE BOX

WITH REMOTE CONTROL ENGINE STARTER OR WIRELESS CHARGER HARNESS 6-PIN CONNECTOR

Plug in here.


FUSE BOX

Plug in here.

WITH REMOTE CONTROL ENGINE STARTER AND WIRELESS CHARGER HARNESS 6-PIN CONNECTOR

FRONT VIEW


57. Secure the relay harness to the vehicle harness with five wire ties.

If the vehicle is equipped with CVT, continue with step 58; otherwise, go to step 59.

With CVT

58. Secure the 1-pin connectors to the vehicle harness with one wire tie. Go to step 60.

5 WIRE TIESRELAY HARNESS

VEHICLE HARNESS

VEHICLE HARNESS

WIRE TIE1-PIN CONNECTORS

8 (1510) 19 of 24

With M/T
59. Secure the 1-pin connectors and relay harness to the vehicle harness with two wire ties.

VEHICLE HARNESS

2 WIRE TIES1-PIN CONNECTORS

RELAY HARNESS

20 of 24 AII02278-0

60. Unplug the vehicle connector from the combination light switch.

61. While pushing the two retaining tabs, slide the combination light switch out and remove it from the steering column. NOTE: Do not pull on the lever when removing the switch.

COMBINATION LIGHT SWITCH(Discard.)

2 RETAINING TABS(Push.)

VEHICLE CONNECTOR

STEERING WHEEL

Do not pull on the lever.


62. Install the new combination light switch to the
steering column. NOTE: Do not push on the lever when installing the switch.

63. Plug the vehicle connector into the new combination light switch.

64. Plug the 20 A fuse into the fuse box.

NEW COMBINATION LIGHT SWITCH

2 RETAINING TABS(Push.)

VEHICLE CONNECTOR

STEERING WHEEL

Do not push on the lever.

FUSE BOX

CONNECTING LOCATION

20 A FUSE

FRONT VIEW


65. Using isopropyl alcohol on a shop towel, thoroughly clean the driver’s kick panel where the fuse label will attach.

66. Attach the fuse label to the driver’s kick panel.

67. Remove the relay box cover.

Clean with isopropyl alcohol.

FUSE LABEL(20 A OPTION FUSE)

ATTACHING

DRIVER’S KICK PANEL

4 RETAINING TABS

RELAY BOX COVER

RELAY BOX

8 (1510) 21 of 24

68. Using isopropyl alcohol on a shop towel, thoroughly
clean the relay box cover where the fuse label will attach.

69. Using scissors, cut the fuse label and attach the fuse label to the relay box cover.

70. Check that all wire harnesses are routed properly and all connectors are plugged in.

71. Install all removed parts.

72. Connect the negative cable to the battery.

73. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions.

Clean with isopropyl alcohol.

FUSE LABEL

ATTACHING

RELAY BOX COVER

2 mm(0.08 in.)

FUSE LABEL

22 of 24 AII02278-0

74. Reset the clock.

75. If necessary restore the systems back to normal operation as described in the service information.

Check the Operation of the Fog Light

76. Turn on the headlights (low beam).

77. Turn on the fog light switch (indicator is on).

78. If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable.

NOTE: The fog light lenses may cloud when the outside temperature is cold; this is normal and should go away in warm weather.

QC00130AH

FOG

LIG

HT

SWIT

CH

HEADLIGHT SWITCH

Low HighOFF

OFF -

ON

- - -

- - -

The auto light model is shown.


Fog Light Aiming Adjustment
79. Adjust the fog light:

• Adjust the aim according to your local laws and regulations.

• To adjust, turn the adjustment point in or out until the correct aim is obtained.

BULB REPLACEMENT

1. Release the front inner fender.

PHILLIPS SCREWDRIVER

FOG LIGHT

ADJUSTER

BOLT2 CLIPS

FRONT INNER FENDER(Pull down.)


2. Unplug the connector from the fog light.

3. Remove the bulb from the fog light as shown.NOTE: Right fog light bulb turns clockwise.

CONNECTOR

BULB (Turn.)

FOG LIGHT

8 (1510) 23 of 24

4. Install the new bulb.
• Use only a genuine Honda halogen light bulb with this Specified Wattage: Rating: 12V 35W H8 Halogen Light Bulb P/N 33165-TL0-003

• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or mild detergent solution.

• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, may annoy oncoming driver’s view.

5. Install all removed parts. Check that the wire harness is not pinched. Be sure to tighten the clips and bolt securely.

6. Check the operation of the fog light; readjust the aim if necessary.

Turn the bulb until it stops.

FOG LIGHT

NEW BULB

NEW BULB

CONNECTOR

24 of 24 AII02278-0

22. Install the left fog light to the front bumper with three self-tapping screws. 23. Install the...

Documents

Transcript of 22. Install the left fog light to the front bumper with three self-tapping screws. 23. Install the...