2117.WORKABOUT PRO 3 S Quick Start Guide

2
ISO 9001 Certified Quality Management System Hand-Held Computer S Version Quick Start Guide Contents of the box: The WORKABOUT PRO 3 This Guide Additional documentation (dependent on order) Features: Front Speaker Stylus Scan Bar LED Indicator Tether Port Beeper Port DC Input LIF Port LED Indicator Stylus Microphone Port Battery Cover Back Cover Endcap Features: Back and Keyboard Features: Typical Variants Version without scanner or GSM radio Version with GSM radio and scanner in endcap Version with serial port in endcap Version with scanner in pod Version with pistol grip SIM Card Slot (if present) SD Card Slot Note: The SIM Card slot may be covered on your unit. Battery Contacts FCC Labels On/Off Switch Battery Cover Battery Fasteners On/Off Switch Features: The Battery Compartment Getting Started Switch the hardware on. Insert the battery. Close and lock the battery cover. Over 1 2 3 ON Battery Fasteners Turn the fasteners towards the centre of the unit to lock the battery cover. February 9, 2010 PN 8000199.A Microphone Port

description

 

Transcript of 2117.WORKABOUT PRO 3 S Quick Start Guide

Page 1: 2117.WORKABOUT PRO 3 S Quick Start Guide

ISO 9001 CertifiedQuality Management System

Hand-Held ComputerS VersionQuick Start Guide

Contents of the box:

The WORKABOUT PRO3

This Guide

Additional documentation(dependent on order)

Features: FrontSpeaker Stylus

Scan Bar

LEDIndicator

Tether Port

Beeper PortDC Input

LIF Port

LEDIndicator

StylusMicrophone

Port

Battery Cover

Back Cover

Endcap

Features: Back and Keyboard

Features: Typical Variants

Version withoutscanner orGSM radio

Version with GSM radio and scanner in endcap

Version with serialport in endcap

Version with scannerin pod

Version with pistol grip

SIM Card Slot(if present)

SD Card Slot

Note: The SIM Card slotmay be covered on your unit.

Battery Contacts

FCC Labels

On/Off Switch

Battery Cover

Battery Fasteners

On/Off Switch

Features: The Battery Compartment Getting StartedSwitch the hardware on.

Insert the battery.

Close and lockthe battery cover.

Over

1

2

3

ON

Battery Fasteners

Turn the fasteners towardsthe centre of the unitto lock the battery cover.

February 9, 2010 PN 8000199.A

Microphone Port

Page 2: 2117.WORKABOUT PRO 3 S Quick Start Guide

4 Charge the battery. The power adaptor maybe plugged directly into the WORKABOUT PRO3.

The WORKABOUT PRO3 may also be chargedin a Docking Station.

Note: Use only theuniversal AC poweradaptor approved byPsion Teklogix for theWORKABOUT PRO3.

Note: Full battery performance isonly reached after the first few fullcharge/discharge cycles.

5 - 40°C41 - 104°F 6h

5 Turn the unit on. Press the Power keyfor a few seconds.

6 Connect the WORKABOUT PRO3 to thehost computer. Connect using a Tether Port toUSB cable, or through a Docking Station.

7

8 Configure ActiveSync. Follow the onscreen instructions provided by ActiveSync to establish a connection between the host computer and the WORKABOUT PRO3.

ISO 9001 CertifiedQuality Management System

Install ActiveSync®. Go to http://go.microsoft.com/fwlink/?LinkId=147001 and follow the instructions to download and install ActiveSync 4.5 or higher.Note: ActiveSync is not needed when connecting to a host computer that uses the Windows® Mobile Device Center (such as Microsoft® Windows Vista®).

Hand-Held ComputerS Version

Quick Start Guide

To turn the WORKABOUT PRO3 off, do one of the following:

Press the • Power button, orSelect • Shut down from the Start menu.

Resetting the unit Important: Resetting may result in data loss.

To perform a cold reset:Press the • SCAN bar, the FN/BLUE key, and the ENTER key simultaneously for a few seconds. During a cold reset, running programs are halted and RAM memory is cleared. The contents of flash memory and the registry are preserved. The operating system is reloaded.

To perform a warm reset:Press the • FN/BLUE key and the ENTER key simultaneously for a few seconds. During a warm reset, running programs are halted. The contents of RAM, flash memory and the registry are preserved.

Power Button

Allow the WORKABOUT PRO3 to chargefor 6 hours.

February 9, 2010 PN 8000199.A

Rev. A8 0 0 0 1 9 9