2019 - Sawblades T.C.T. SAWBLADES
Transcript of 2019 - Sawblades T.C.T. SAWBLADES
Low noise sawbladesAccording to the latest technical tests, our saw blades are manufactured with an advanced system of noise reduction guaranteed byan attentive position of the laser ornaments, different for each diameter (♫).The body of the saw blade remains solid and perfectly tensioned while sound waves generated during the working process are absor-bed either longitudinally or crosswise.The laser ornaments in the sizing saw blades (Items HBS/HBC) and in the saw blades for cutting PVC (item LE) and for cutting alumi-nium (items LA/LB) are filled up with a special soundproofing plastic resin (♫), resistant to ultrasound and high temperatures.Considerably lowering the vibrations, the tool can work longer and perform a better finish cut, also after its resharpening.
0 1 2 3 4 5 6 7 8 9 10
0 1 2 3 4 5 6 7 8 9 10
0 1 2 3 4 5 6 7 8 9 10
T.C.T. SAWBLADES
sawblades are high quality products, guaranteed by the choice of raw materials developed in collaboration with leadingEuropean manufacturers of steel and carbide (i. e. our carbide tips are produced by Ceratizit).Throughout the production cycle, controls are followed extremely scrupulous and final acceptance ensures that all the characteri-stics of the blades are meeting the highest standards of quality. At the end the production lots are numbered and filed.
The sawblades are exclusively worked withlaser cutting. Bores and keyways are honed toensure maximum precision (h7). Without this pro-cess there will be a visible mark on the bore edge.
Tensioning and balancing are operated with comple-tely automatic machines, which assure the absenceof vibrations and higher quality results.
Lasermark
Quality of tungsten carbide used:
12.03
2019 - Sawblades
Quality Composition Grain size Bending Hardness Density Toughness Wear resistance strength
KCR05 ISO: K01USA: C4KCR06 ISO: K01USA: C4
Co+Ni 2,76%, Ultrafine grain0,2-∠0,5 μm
2500 MPa363.000 P.S.I.
2150 HV102110 HV3094,4 HRA
15,20 g/cm3 6,0 MPa.m-1/20 1 2 3 4 5 6 7 8 9 10
Co+Ni 3,0%, Micrograin0,5-∠0,8 μm
2300 MPa334.000 P.S.I.
1950 HV101910 HV3093,6 HRA
15,25 g/cm3 8,5 MPa.m-1/2
HC10 ISO: K10USA: C3
Co 5,6%, Fine grain0,8-∠1,3 μm
2150 MPa334.000 P.S.I.
1760 HV101730 HV3092,7 HRA
15,00 g/cm3 9,2 MPa.m-1/2
HC20 ISO: K20
USA: C2-C3Co 6,0%, Fine grain
0,8-∠1,3 μm 2200 MPa
334.000 P.S.I.
1640 HV101620 HV3092,1 HRA
15,00 g/cm3 9,9 MPa.m-1/2
SMX ISO: P20-P25USA: C6
Co 10.5%, Fine grain0,8-∠1,3 μm
2200 MPa316.000 P.S.I.
1550 HV101530 HV3091,5 HRA
12,65 g/cm3 10,0 MPa.m-1/2
0 1 2 3 4 5 6 7 8 9 10
®
®
®
Technical data and images are just an indication. SISTEMI srl reserves the right to modify the above information at any time and without notice.
H7 bore
Tensioning andbalancing
Low-noiselaser cuts
High quality T.C.T.
Item D d B/c Z a P. holesCCS250.04830 ♫ 250 30 3,2/2,2 48 15° PH02CCS300.06030 ♫ 300 30 3,2/2,2 60 15° PH02
α
D
d
Recommended peripheral cutting speed:
CUTTING MATERIAL Peripheral cutting speed (m/s) Feed rate (mm/z)
Softwood
Hardwood
Exotic timberPlywoodParticle boardHDF MDF Playwood boards, veneered or coated on both sidesLaminated boardsMelamineThermoplasticDuroplasticAluminium profiles
Cutting along grainCutting across grainCutting along grainCutting across grainCutting along grain
58÷10060÷10061÷10065÷10058÷10055÷8060÷8560÷8060÷8060÷10055÷8058÷8050÷7530÷6035÷70
0,5÷3,00,2÷0,40,3÷1,00,2÷0,80,3÷1,00,1÷0,20,30,1÷0,30,1÷0,30,20,1-0,250,150,05-0,10,02-0,050,005-0,08
Diagram for determining the peripheral cutting speed:Diagram shows the peripheral cutting speed in m/sec, defined RPM and sawblades diameter.
- Mineral fibreplates - Wood-based material, plastic material and non-ferrous metal- Hardwood - Softwood- Safety limit
12.04
2019 - Sawblades
1500 2000 2500 2800 3000 3500 4000 4500 5000 5600 6000 8000 9000 10000 12000 18000
80 6,5 8,5 10,5 12 13 14 15 19,1 21 23,5 26 34 38 42 52 7690 7 9,5 12 13,5 14 16 17 21 24 26,5 28 38 42 48 56 84100 8 10 13 15 16 18 21 24 26 29 31 41 47 52 63 96120 9,5 13 16 18 19 22 25 28 31 35 38 49 57 63 65125 10 14 16,5 20 19,5 24 27 31 34 36,5 41 53 61 68 82140 11 15 18 21 22 26 29 33 37 41 44 57 66 73 88150 12 16 19,5 22 23,5 27 31 35 39 44 47 63 71 79 94160 13 17 21 24 26 29 33 38 42 47 50 65 75 84180 14 19 24 27 28 33 42 42 47 53 57 73 85 94200 16 21 26 29 32 37 42 47 52 58,5 63 81 94225 17 23 30 32 36 40 46 52 58 66 69 92 104250 20 26 33 37 40 46 52 59 65 73,5 79300 24 31 40 44 48 55 63 71 79 88 94350 27 37 47 51 56 64 73 83 92 105 400 31 42 54 59 64 73 83 92 105450 35 47 59 66 70,5 83 94 105500 39 52 67 73 80 92
D x π x n60 x 1.000
Vt =
Vt = cutting speed (m/sec)D = sawblades diameter (mm)n = RPM
RPM
D=mm
12.05
2019 - Sawblades
Instructions for a correct use of sawblades:1- Be sure the spindle where the sawblade has to be mounted is clean and balanced;2- Be sure the sawblade is perfectly aligned with the working table;3- Be sure the working parameters (feed rate, cutting speed, etc.) are correct;4- Never exceed the RPM indicated on the sawblade, otherwise it can be dangerous for the operator;5- Check time to time the state of the cutting tips and, in case, let the sawblade professionally resharpened;6- When processing thicker material, reduce the number of teeth;7- Use flanges of the same diameter of the saw blade to secure it (or at least 1/3 of the blade’s diameter);8- The machine must be in perfect condition, without any unusual vibrations;9- Reduce the number of teeth when processing thicker material.
Scale 1:1
Pin holes as per following details:
PH01
Name Nr of holes/diameter of holes/pitch circle diameterPH01 2/10/60
Scale 1:1
PH02
Name Nr of holes/diameter of holes/pitch circle diameter Machine typePH02 2/7/42 + 2/9,5/46,5 + 2/10/60 Universal
12.06
2019 - Sawblades
Reference table for the choice of the right sawblade (X= sufficient - XX= good - XXX= excellent) Information just as a guide
Item
Natural woods Pressed woodsSOFTWOOD
(cider, poplar, pine)Rip cut Cross cut
XXX XXX
X XX X XX X X
XXX XXX XX XX X X XXX XX
Rip cut Cross cut Rip cut Cross cut
HARDWOOD(ash, walnut, teak) EXOTIC TIMBER PLYWOOD PARTICAL
BOARD
BLOCK
BOARD
LAMINATEDVENEERED
Board materials Paperandmineralfiber
Art. AA - Page 12.12
Art. AB - Page 12.13
Art. AL - Page 12.13
Art. CA - Page 12.14
Art. CB - Page 12.14
Art. CC - Page 12.14
Art. CD - Page 12.15
Art. CE - Page 12.15
Art. CF - Page 12.16
Art. CG - Page 12.16
Art. CH - Page 12.16
Art. DA - Page 12.16
Art. DC - Page 12.17
Art. FAS - Page 12.17
Art. FB - Page 12.17
Art. FCS - Page 12.18
Art. FE - Page 12.19
Art. FG - Page 12.19
Art. FH - Page 12.20
Art. FK - Page 12.20
Art. FI - Page 12.27
Art. FL - Page 12.28
Art. FM - Page 12.30
Art. FP - Page 12.30
Art. GA - Page 12.31
Art. HBS - Page 12.28
Art. HCS - Page 12.29
Art. KA - Page 12.33
Art. LA - Page 12.32
Art. LB - Page 12.32
Art. LZ - Page 12.34
Art. MES - Page 12.34
Art. MGS/LEPages 12.33/12.34
A.MLS/MMS - P. 12.34
Art. MP - Page 12.34
Art. PA - Page 12.35
Art. PB - Page 12.35
Art. XFC - Page 12.35
Art. XFI - Page 12.36
Art. XHC - Page 12.37
XXX XX XXX XX XX XX X XXX XX
X
XX
XX
X XXX
XX XX XXX XXX XX XX XXX XX X X
XXX XX XXX XXX X
X
XXX XX XXX XXX XX XX
XXX XXX XXX XXX XXX XXX XXX X XX XX
X X
XXXXX XX XXX XXXXX XXX XXX X
X XX XX XX XX XXXX
XX XX X
XXXXX XX XXX XXXXX XXX XXX X XX XX XXX
XXX X X X XXXX
XXX XX XXX XX XXX X XX X XXXX XX
XX XX X
X
X
X
X
X
X
X
X
X
XXX XX XX XXX XXX
XX XXX XXX XXX XXX
XXX XX XX XX XX XX
XXX XX XXX XX XX XX
XXX XX XXX XX XX XX
XX XX XXXXX XX XXX
XXXXX XXX XXX XXX
XXXXX XXX XXX XXX
XXXXX XXX XXX XXX
XXXXX XXX XXX XXX
XXX XX XXX XX X X
XXX
XXX XXX
XX XX XX
XXX XXX XXX
XXX
X
X
X
X
X
X
X
X XX XX X X X X
XXX XXX XX XXX XX XX
XXX XXX XXX XXX XX XX XX XX X XX XX
XX XX XXX XXX XXX XXX XXX XX XX
XX XX XXX XXX XXX XXX XXX XX XX
XX XX XXX XXX XXX XXX XXX XX XX
XXXXX
12.07
2019 - Sawblades
Reference table for the choice of the right sawblade (X= sufficient - XX= good - XXX= excellent) Information just as a guide
Item
Panels Plastic materials Sandwich Non-ferrous materials
FIBERHDF MDF
X
XXX XX XX XX XX XX
XX XX XX XXX XX XX
ALUMINIUMALOYS
PLASTIC
COATED
THERMOPLASTIC DUROPLASTICS WITH PLASTICBINDERS
ALUMINIUMPROFILES
ALLUMINIUM PROFILES SOLID
Ferrous materials
Art. AA - Page 12.12
Art. AB - Page 12.13
Art. AL - Page 12.13
Art. CA - Page 12.14
Art. CB - Page 12.14
Art. CC - Page 12.14
Art. CD - Page 12.15
Art. CE - Page 12.15
Art. CF - Page 12.16
Art. CG - Page 12.16
Art. CH - Page 12.16
Art. DA - Page 12.16
Art. DC - Page 12.17
Art. FAS - Page 12.17
Art. FB - Page 12.17
Art. FCS - Page 12.18
Art. FE - Page 12.19
Art. FG - Page 12.19
Art. FH - Page 12.20
Art. FK - Page 12.20
Art. FI - Page 12.27
Art. FL - Page 12.28
Art. FM - Page 12.30
Art. FP - Page 12.30
Art. GA - Page 12.31
Art. HBS - Page 12.28
Art. HCS - Page 12.29
Art. KA - Page 12.33
Art. LA - Page 12.32
Art. LB - Page 12.32
Art. LZ - Page 12.34
Art. MES - Page 12.34
Art. MGS/LEPages 12.33/12.34
A.MLS/MMS - P. 12.34
Art. MP - Page 12.34
Art. PA - Page 12.35
Art. PB - Page 12.35
Art. XFC - Page 12.35
Art. XFI - Page 12.36
Art. XHC - Page 12.37
X X
X X
X X
XX XX XXX XX X
XX
XXX X XX
XXX XX XX
XX XX
X X
XX
XXX XX XX XX X XXX
XX XXX
XXX X
XXX XXX X
XXX XXX XXX
XXX
XXX XXX XXX
XXX XXX XXX
XXX XXX XXX X X
XXX
XX XX XXXXX
X XXX XX
XXX
XX
XXX XX
XXXX XX
XX
XXX XXX
XX XXX X
XXX X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXX XXX
XXX
XXX XXX XX
XXX XXX XX
XX XX
XX XX X X XX
X
XXX
XX
XXX XXX
XXX XXX
D (diameter/mm) x KSp (thickness/mm)
Number of teeth suggested:Calculation of the number of teeth, given the diameter of the saw blade and the thickness of the material to be worked.
12.08
2019 - Sawblades
Z (nr. theet) =K = 7 for ripcutting on natural woodK = 9 for ripping or crosscuttingK = 11 for crosscutting of hard woods and hard materials
WZ:alternate top bevelteeth, suitable for softand hardwood, fibrematerials, MDF.Especially clean cuts.
FZ/TR:triple chip teeth form,suitable for solidwood, plastic coatedmaterials, non ferrousprofiles, hardwood.
FZ:flat teeth, suitable forcutting along grain onlarge cutting heightsoft and hardwood.
HZ/DZ:Hollow tooth/invertedV-tooth, suitablefor saw benches onplastic coatedchipboards and fibrematerials.
FZ/FA:Flat tooth with bevel,with chip limitor, forcutting timber, also inpresence of concreteor metal remains,nails, etc.
LFZ:flat teeth with chiplimitor, suitablefor table saws. For cutting along andacross grain in wooden boardingmaterials.
KON/FZ:conical tooth, used on scoring blades
WZ/FA:alternate top bevelteeth, suitable for softand hardwood, fibrematerials, MDF.Especially clean cuts.
TR:trapeizodal tooth,used on saw blades“dry” (Item LZ).
ES: (ES-L/ES-R)One-sided top beveltooth (right or left),used on edge bandingmachines or hoggingunits.
BW:special tooth shape for item “PB”(steel blade, for cutting metals).
C:special tooth shapefor item “PA”(steel blade, for cutting metals).
saw blades for portable machines are delivered in hanging packaging while those for industrial machines in a very robust carton packaging.
All packagings are marked with the symbol meaning 100% recyclable carton, vegetable oil-based inks and glues.
Sawblades Dimensions∆127÷∆140 165x179x5∆150÷∆190 215x234x5∆200÷∆240 254x277x5
Sawblades Dimensions∆80÷∆150 210x210x15∆160÷∆210 255x255x15∆220÷∆250 300x300x15∆280÷∆300 355x355x15∆320÷∆350 400x400x15∆355÷∆400 455x455x15∆420÷∆500 550x550x15∆520÷∆600 655x655x15∆620÷∆700 725x725x20
PACKAGING SAW BLADES FOR PORTABLE MACHINES PACKAGING SAW BLADES FOR INDUSTRIAL MACHINES
®
®
Symbols:
12.09
2019 - Sawblades
For cutting along and across grain ofsoftwood
Art. AA - CB - CA - CFDC - KA - LZ XFC - XFI - XHC
For cutting along and across grain ofhardwood
Art. AA - CB - CCDC - KA - LZ XFC - XFI - XHC
For cutting across grain of softwood
Art. FAS
For cutting across grain of hardwood
Art. CD - CECG - FAS
For cutting along grain of softwood
Art. DA - FE - FGFH - FK
For cutting along grain of hardwood
Art. CA - DA - FEFG - FH - FK
For cutting wood for construction withsmall metal parts
Art. AB - ALGA - GB
For cutting MDF
Art. CE - CG - FCSFCT - FM - FPHBS - HCSXFC - XFI - XHC
For cutting aluminium wood profiles
Art. FAS
For cutting “Sandwich” panels
Art. MP
For cutting aluminium profiles
Art. AL - LA - LZ
For cutting steel and ferrous materials
Art. LZ - PA - PB
For cutting PVC
Art. LA - LB - LEMGS
For cutting wood frames
Art. MLS
For cutting PVC frames
Art. MLS
Scoring sawblades for cutting veneer board
Art. FI - FL
Scoring sawblades for cutting laminate materials
Art. FI - FL
Scoring sawblades for cutting MDF
Art. FI - FL
For cutting double side laminate board
Art. FB - FCS - FCT -FM - FP - HBS -HCS - MMS - XFC XHC - XFI
For cutting single side veneer board
Art. AA - CB - CCCD - CE - CGCH - DC
For cutting double side veneer board
Art. FB - FCS - FCT - FIFM - FP - HBSHCS - XFCXFI - XHC
For cutting plastic coated materials
Art. FAS - FCS - FCTFP
For cutting CORIAN®
Art. MES
For working on building sites
Art. GA - GB
For cutting paper coated materials
Art. CB - CC - CH
For cutting plastic materials
Art. AB - AL FB - LZMES - MGS
For cutting plexiglass
Art. CH - MES - MGS
For cutting single side laminate board
Art. CD - CE - CFDC
For cutting aluminium
Art. LB
REFERENCE TABLE FOR PORTABLE MACHINES
12.10
2019 - Sawblades
Diameter Producer Model125 x 12,7 B & D DN55, DN56, D985, D984, DN254
127 x 12,7 B & D DN55, DN56, D985, D984, DN254
130 x 16 Bosch PKS240, PKS40 S, S43Metabo BHK01, KS3340 S, 4340,
6311, BHK2, MaxKS40 S
134 x 20 AEG TKS42Holz-Her 2110, 2111, 2171, Mosquito SPeugeot SC42 C
140 x 12,7 B & D DN227, DN227 H, BD227, BD846, BD 228
140 x 16 Makita 5000SBR, 500, 5000GB, N500
140 x 20 Bosch 1551, 1559Holz-Her 2260, 2270, 170, 260, 270Metabo BTK, C1, C2, BTKOAEG HK 40Peugeot SC47 C, HKS 700, Profiline, SC 1Stayer Profiline, CP 46
150 x 13 Kress 6006, 6018, 9060, HKS400, 6000, 6010Mafell BiberellaSkil 533, 553
150 x 16 Bosch PKS46, S33, S1, GKS12V, GB1923 (England)
Scheer/Ryobi MS 50Skil 52465
150 x 20 AEG HK45A, HK50, HK52, HKS52, HK737HK46S, AHK52, HK46N, HK46, HK45
B & D P88.09Casals BSC150, VSC50De Walt DW 351Felisatti TP 751Metabo 4341S, KS52 S, KS0846, BTK0, 62, 61,
KSO846 S, KSO852 S, KSE0946 SPerles KS50Stayer CP50Peugeot SC53 C, SC52, SC52 C, SC46Hitachi C5, FC5, FC5 SAFein SSK646Skil 1850H, 1850Elu MH151Scheer/Ryobi MS45, 45E, MS45-3Makita 5600 B
150 x 30 Festo AXF45, AF45 EElu MH18
156 x 12,7 B & D DN228, DN57, SR352E, BD228,P36-01, BD228L, BD228CK, SR352
Use reduction rings Art. ZA page 10.14to have different bores in your sawblades
REFERENCE TABLE FOR PORTABLE MACHINES
Diameter Producer Model160 x 16 B & D M336, M975, M976, BD855
Bosch PKS54, GKS54CE, PKS54CE, GKS54Peugeot SC4510XARockwell 63416Ryobi W5502 CScheer FMSkil 534, 536, 552B, 416H, 1409H, 1408H,
552H, 1855H, 367, 856, 1410HUlmia 1607, 1610
160 x 20 AEG HK55A, HK55B, HK160A, HK160BAtlas Copco K55S, K55SEFestool T555Haffner KSU50Hitachi FC65A, C6DAMafell X55, XE55, PS52, MKS55, MS55,
A55, B55, FU50Makita 5600NB, 5600 DWMetabo KS1155SKress 6050, 6055 Duo, 1050KSHolz-Her HKU50, HKU264, 1420, 2103,
2104, 2105, 2106Ryobi W-560 (P), W5502Fein SSK660Festo ATF55E, ATF55, AP55E, AP55, AP55E-FSProtool CSP55Techline EHS 160Tip HKS 160Valex SC 160
160 x 30 Festo AU50, AUP50, AAUMafell KS320
165 x 20 Festo 5603R
170 x 20 Makita 5600 BRMafell B55, FK50, A55, FUS50
170 x 30 Elu MH 155, MH55, MH 65Festo AM42S+A, AMT42S, AXT55,
AT55E, AXT50LAHolz-Her 2115(t55A), 2266, 2271,
2281, 281, HKUS266Haffner KSU110Bosch 1552, 1556, 1563, GKS55Hitachi PSU6, C-6SA
180 x 20 Makita SR1800, 5800B, 5801 B, 5800, 5800N, S800BR
Haffner KSU60, SKU113Peugeot FIP50SMetabo 6317SRyobi W-66N, W-651A, W-6502B & D HS1200, HD2062
180 x 30 Elu MH65Bosch 0550, 1560, 1557, 1550, 1553Festo AU60S, AU55S, AU60P, AUT60S,
AUT42SHolz-Her 2112, HKU55, HKU2272, HKU2291,
2113, 2292, 2282, 2269Haffner KSU113
Use reduction rings Art. ZA page 10.14to have different bores in your sawblades
REFERENCE TABLE FOR PORTABLE MACHINES
12.11
2019 - Sawblades
Diameter Producer Model184 x 16 B & D HD1000, DN59, DN229, DN820
SR300, P37-03, P37-05, GD60,HD1200P, HD2062, SEC718, SR362EBD229, BD865E
Skil 1865U, 77, 77U, 537, 553B, 553H,559, 559U, 574U, 857, 1865H
Wolf 6070Peugeot SC66C, SC650, 10XA, SC65CRockwell 315, 4500, 63417
190 x 16 Bosch PKS65, P300, P30Skil 1865U, 1965U, 1865H
190 x 20 Makita 5800BR, 3501Kress 6060, CHKS6060, 1400KS, 1600KS,
1600HTKSMetabo KS4345S, 5348, KS4346S, KS65S,
Robert, BTK, KSE1668S
190 x 30 AEG HK65A, HK65, HKS65, HK190, HK66,HKS66, HKSE66, HKE66, HKS65A
Atlas Copco K66S, K66SEHolz-Her 2116(t-65a), 2117(t65i), 2127, 2119,
2269(t65e), 2126, 2282, 2114, 2292, 2113Bosch 1553, 0051, 1564, PKS66, GKS66CE,
GKS65, PKS66CEDe walt DW65, DW365Elu MH165Hitachi FC75A, PSM-7, PSU-7Felisatti TP765, TP766Festo AP65E, AP65E-FS, AT65EMafell MKS65Skil 1965UScheer MS 65Makita 5703R
200 x 16 B & D M338Hanning TK200, TK20S, TK20N, TK300Ulmia 1607, 1708Ryobi W750
200 x 30 Festo AU65S, AD65, AXP65, AXP200, AP68E, AP65S
AEG HK200, HK201Bosch 1561, 0551Haffner AKSMafell B65, X72Holz-Her 2113, 2292, 2555Kity 0618Scheer MS 70, FM16DNC,
FM16Electronic,FM16StandardMakita 5700Ulmia 1706Valex SC200
210 x 25 Makita SR2100, LS0810, 2708Skil 1524H, 1873H, 1525, 1886, 1985, 1986
Use reduction rings Art. ZA page 10.14to have different bores in your sawblades
REFERENCE TABLE FOR PORTABLE MACHINES
Diameter Producer Model210 x 30 AEG HK75A, HK75, HKS75
Atlas Copco HKS75Fein SSK661Elu MH82, MH182, MH30Casals SC210, VSC70B & D SEC818, DN800, DN810, PS174,
SR700, P38.02, BD800, HD2075SBosch 1554, 1588, 1565, GKS75SHaffner RS75, KSU118Hitachi PSU8, PSM8, C8U, C8FAHolz-Her 2264, 2267, 2284, PKS267, 2279Mafell MKS75, MKS85S, MS75Perles KS70Skil 1873H, 1524HMetabo KSE 1678, KG 1670
216 x 30 De Walt DW712, DW771, DW777
220 x 20 Flott 2000, KS3000Schleicher Compact151
220 x 30 Festo AU77S,Haffner KL177, KL178, KSU118Holz-Her PKS+HKU75, 274, 1205, 1331,
1342, 1345, 1346, 2279Metabo 6322SScheer MS80, M585
225 x 30 Festo CS70EB
230 x 30 Holz-Her 2218(t85i), 2120(t85e), 2293, 2294AEG HKS85Atlas Copco HKS85B & D P39-02, SEC918, HD2086SBosch 1562, 0052, 1566, GKS85SCasals SC230Haffner SP187, KS85, HUS85Skil 1886HScheer MS85
235 x 25 Makita SR2300, 5900BR, 5900B, 5900
235 x 30 De Walt DW383Haffner KL176, KS85, KSU85, SP187B & D P39-02, SEC 918 Skil 1986Makita 5903RHitachi C9U, PSM9, PSU9
240 x 30 Festo AXP85, AP85E, AP88E, AP85-E-TSHolz-Her 2268, HKD65Metabo 6323 S, KS1785S, KS6323S AutomaticElu MH85Bosch 1555Mafell B82, MKS85Hitachi PSM-9, PSU-9AEG HK240De Walt DW86
305 x 30 De Walt DW718, DWS780
Use reduction rings Art. ZA page 10.14to have different bores in your sawblades
HW SAWBLADES FOR PORTABLE MACHINESART. AA
Item D d B/c Z Pin holesAA127.03613 125 12,7 2,6/1,6 36
AA130.02016 130 16 2,6/1,6 20AA130.03616 130 16 2,6/1,6 36
AA134.03620 134 20 2,6/1,6 36
AA140.02013 140 12,7 2,6/1,6 20AA140.02016 140 16 2,6/1,6 20AA140.02020 140 20 2,6/1,6 20AA140.03020 140 20 2,6/1,6 30AA140.04213 140 12,7 2,6/1,6 42AA140.04216 140 16 2,6/1,6 42AA140.04220 140 20 2,6/1,6 42
AA150.02016 150 16 2,6/1,6 24AA150.02020 150 20 2,6/1,6 24AA150.02030 150 30 2,6/1,6 24AA150.03016 150 16 2,6/1,6 40AA150.03020 150 20 2,6/1,6 40AA150.04820 150 20 2,6/1,6 48AA150.04830 150 30 2,6/1,6 48
AA156.04813 selling out 156,5 12,7 2,6/1,8 48
AA160.02416 160 16 2,6/1,6 24 2/6/32AA160.02420 160 20 2,6/1,6 24 2/6/32AA160.02430 160 30 2,6/1,6 24 2/7/42AA160.03016 160 16 2,6/1,6 30 2/6/32AA160.03020 160 20 2,6/1,6 30 2/6/32AA160.03030 160 30 2,6/1,6 30 2/7/42AA160.04816 160 16 2,6/1,6 48 2/6/32AA160.04820 160 20 2,6/1,6 48 2/6/32
AA165.02420 165 20 2,6/1,8 24
AA170.03030 170 30 2,6/1,6 30 2/7/42AA170.05230 170 30 2,6/1,6 52 2/7/42
Item D d B/c Z Pin holesAA180.02420 180 20 2,6/1,6 24 2/6/32AA180.02430 180 30 2,6/1,6 24 2/7/42AA180.03020 180 20 2,6/1,6 40 2/6/32AA180.03030 180 30 2,6/1,6 40 2/7/42AA180.05620 180 20 2,6/1,6 56 2/6/32AA180.05630 180 30 2,6/1,6 56 2/7/42
AA184.03016 184 16 2,6/1,6 30 AA184.05616 184 16 2,6/1,6 56
AA190.02416 190 16 2,6/1,6 24 2/6/32 AA190.02420 190 20 2,6/1,6 24 2/6/32 AA190.02430 190 30 2,6/1,6 24 2/7/42 AA190.03616 190 16 2,6/1,6 40 2/6/32 AA190.03620 190 20 2,6/1,6 40 2/6/32 AA190.03630 190 30 2,6/1,6 40 2/7/42 AA190.05616 190 16 2,6/1,6 56 2/6/32 AA190.05620 190 20 2,6/1,6 56 2/6/32 AA190.05630 190 30 2,6/1,6 56 2/7/42
AA200.02430 200 30 2,6/1,8 24 2/7/42 AA200.03630 200 30 2,6/1,8 36 2/7/42 AA200.06430 200 30 2,6/1,8 64 2/7/42
AA210.02430 210 30 2,8/1,8 24 2/7/42 AA210.03625 210 25 2,8/1,8 36 2/7/42AA210.03630 210 30 2,8/1,8 36 2/7/42 AA210.06430 210 30 2,8/1,8 64 2/7/42
AA220.02430 selling out 220 30 2,6/1,8 24AA220.03630 220 30 2,8/1,8 36 2/7/42 AA220.06430 220 30 2,8/1,8 64 2/7/42
AA225.03430 225 30 2,6/1,8 34 2/7/42
AA230.02430 230 30 2,8/1,8 24 2/7/42 AA230.03630 230 30 2,8/1,8 36 2/7/42 AA230.06430 230 30 2,8/1,8 64 2/7/42
AA235.03625 235 25 2,8/1,8 36 2/7/42 AA235.03630 235 30 2,8/1,8 36 2/7/42 AA235.06430 235 30 2,8/1,8 64 2/7/42
AA240.03630 240 30 2,8/1,8 36 2/7/42AA240.07230 240 30 2,8/1,8 72 2/7/42
- Fine cut HW sawblades- WZ alternate top bevel teeth- For cutting along and across grain of softwood, hardwood, exotic timber and veneer boards
- High teeth number sawblades best finishing cut- HW grade: HC10 (K10-C3)
12.12
2019 - Sawblades
BASE 1 modular panelSmall display, ideal for starting with a basic assortment
Dimensions (cm): 110 (L) x 90 (H) x 30 (P)
12.13
2019 - Sawblades
HW SAWBLADES FOR PORTABLE MACHINESART. AB
Item D d B/c ZAB216.02430 216 30 3,0/2,0 24AB216.04830 216 30 3,0/2,0 48AB216.06030 216 30 3,0/2,0 60
AB305.06030 305 30 3,2/2,2 60
- Fine cut HW sawblades- WZ alternate top bevel teeth - For cutting plastic materials andwood for construction with small metal parts
- 5° negative hook angle- HW grade: HC10 (K10-C3)
HW SAWBLADES FOR PORTABLE MACHINESART. AL
Item D d B/c ZAL160.02416 160 16 2,6/1,6 40AL160.02420 160 20 2,6/1,6 40AL160.05620 160 20 2,2/1,6 56
AL180.02420 180 20 2,6/1,6 48
AL190.03020 190 20 2,6/1,6 54AL190.03030 190 30 2,6/1,6 54
AL210.03430 210 30 2,6/1,6 54
AL216.06030 216 30 3,0/2,0 64
AL220.03430 220 30 3,0/2,0 64
- Fine cut HW sawblades- FZ/TR triple chip teeth- For cutting Alu-panels, laminated materials, plastics, solid surface and wood for construction with small metal parts
- 5° negative hook angle- HW grade: HC10 (K10-C3)
HW GROOVING CUTTER FOR “LAMELLO®”ART. AH
Item D d B/c ZAH100.10622 100 22 3,96/2,8 8 AH100.21222 100 22 3,96/2,8 12
- For grooving of “Lamello®” joints- Cutter with 2 teeth positive + 4 teeth negative for best finishing cut - HW grade: HC10 (K10-C3)
- Fine cut HW sawblades- WZ alternate top bevel teeth- For grooving of “Lamello®” joints- HW grade: HC10 (K10-C3)
Item D d B/c ZAH100.20622 100 22 3,96/2,8 2 pos.+4 neg.Cutter with reversible knives art. TAH100.20622 (page 13.22)
Grooving cutter for“Lamello®”
“Lamello®”-groove cutter
DP GROOVE CUTTER FOR “LAMELLO®“ JOINTSART. XAH
Item D d B Z Pin holesXAH100.10330 NEW 100,4 30 7 3 4/6,6/48 XAH100.10630 NEW 100,4 30 7 6 4/6,6/48XAH100.10322 NEW 100,4 22 7 3 4/4/36
- Suitable for making Clamex P connecting fittings for furniture, shelve units and kitchen making- To be used both on CNC machines and ZETA P2 hand power tool- Recommended for grooving corner and longitudinal joints on hardwood, veneered and laminated MDF with the P-System anchorage
15
1,5 1,5
10
① ② ③
CLAMEX P JOINTS P-SYSTEM ANCHORAGE
D d
B
B
12.14
2019 - Sawblades
HW MULTI PURPOSE CIRCULAR SAWBLADES ART. CA - CB/CBS - CC/CCS
ART. CA
Item D d B/c Z a Pin holesCA200.02430 selling out 200 30 3,2/2,2 24 14°CA250.03030 250 30 3,2/2,2 30 14° PH02
CA300.03630 300 30 3,2/2,2 36 14° PH02CA350.04230 350 30 3,5/2,5 42 14° PH02
CA400.04830 400 30 4,0/2,8 48 14° PH02CA450.05430 450 30 4,2/2,8 54 14° PH01
CA500.06030 500 30 4,2/2,8 60 14° PH01CA550.06030 550 30 5,2/3,6 60 14° PH01
CA600.06030 600 30 5,2/3,6 60 14° PH01
CA700.06440 700 40 6,2/4,0 64 14° PH01
- WZ alternate top bevel teeth- Suitable for table saws and panels saws - Suitable for particle board in stack- ♫ = no-noise- HW grade: KCR06 (K01-C4)
- Suitable for ripping of hardwood and plywoodfor cutting across grain suitable for softwood
Pin holes: PH01= 2/10/60 - PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
ART. CB - CBS- For cutting along and across grain of softwood and hardwood, single sided veneer-paper boards and plywood
ART. CC - CCS
Item D d B/c Z a Pin holesCC 200.04230 200 30 3,2/2,2 42 10°
CCS250.04830 ♫ 250 30 3,2/2,2 48 10° PH02
CCS300.06030 ♫ 300 30 3,2/2,2 60 10° PH02
CCS350.07230 ♫ 350 30 3,5/2,5 72 10° PH02
CC 400.08430 ♫ 400 30 4,0/2,8 80 10° PH02
- For cutting along and across grain fine finish suitable for hardwood, single sided veneer-plastic boards, plywood and hardwood
α
Item D d B/c Z a Pin holesCB 100.02020 100 20 3,2/2,2 20 10°CB 120.02020 120 20 3,2/2,2 20 10°CB 150.02430 150 30 3,2/2,2 24 10°CB 180.03030 180 30 3,2/2,2 30 10°
CB 200.03230 200 30 3,2/2,2 34 10°
CBS250.04230 ♫ 250 30 3,2/2,2 40 10° PH02
CBS300.04830 ♫ 300 30 3,2/2,2 48 10° PH02
CB 315.04830 315 30 3,2/2,2 48 10°
CBS350.05430 ♫ 350 30 3,5/2,5 54 10° PH02
CBS350.05435 ♫ 350 35 3,5/2,5 54 10° PH02 CBS400.06030 ♫ 400 30 4,0/2,8 60 10° PH02
CB 450.06630 450 30 4,2/2,8 66 10° PH01
CB 500.07230 500 30 4,2/2,8 72 10° PH01
CB 600.08030 600 30 5,2/3,6 80 10° PH01
CB 700.08440 700 40 6,2/4,0 84 10° PH01
C
12.15
2019 - Sawblades
ART. CD - CDS
Item D d B/c Z Pin holes CD 150.03630 150 30 3,2/2,2 36
CD 200.04830 200 30 3,2/2,2 48
CDS250.06030 ♫ 250 30 3,2/2,2 60 PH02CDS250.06035 ♫ 250 35 3,2/2,2 60 PH02
CD 280.06030 280 30 3,2/2,2 60 PH02
CDS300.07230 ♫ 300 30 3,2/2,2 72 PH02 CDS300.07235 ♫ 300 35 3,2/2,2 72 PH02
CDS315.07230 ♫ 315 30 3,2/2,2 72 PH02
CDS350.08430 ♫ 350 30 3,5/2,5 84 PH02 CDS350.08435 ♫ 350 35 3,5/2,5 84 PH02
CDS400.09630 ♫ 400 30 4,0/2,8 96 PH02
CD 450.10830 450 30 4,2/2,8 108 PH01
CD 500.12030 500 30 4,2/3,0 120 PH01
- For cutting across grain of exotic timber and hardwood, single sided veneer, laminate boards and plastic coated materials
- Extra fine finish
HW TRIMMING FINISHING ART. CD/CDS - CE/CES
- WZ alternate top bevel teeth- Suitable for table saws and panels saws - Suitable for particle board in stack- ♫ = no-noise- HW grade: KCR06 (K01-C4)Pin holes: PH01= 2/10/60 - PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
Item D d B/c Z Pin holes CE 150.04830 150 30 3,2/2,2 48
CE 180.05430 180 30 3,2/2,2 56
CE 200.06430 200 30 3,2/2,2 64
CES250.08030 ♫ 250 30 3,2/2,2 80 PH02
CES300.09630 ♫ 300 30 3,2/2,2 96 PH02
CES350.10830 ♫ 350 30 3,5/2,5 112 PH02
CES400.12030 ♫ 400 30 4,0/2,8 120 PH02
CE 450.13230 450 30 4,2/3,0 132 PH01
CE 500.14430 500 30 4,2/3,0 144 PH01
- For cutting across grain of exotic and hardwood, for cutting double-sided veneer boards, single sided laminate boards, MDF and hard boards
- Extra fine finish
ART. CE - CES
RPM suggested referred to the blade diameter
CONTACT US(+39) 0721 28950
visit our websitewww.sistemiklein.com
10°
12.16
2019 - Sawblades
HW MULTI PURPOSE SAWBLADES (THIN KERF)ART. CF - CG - CH
- WZ alternate teeth- Suitable for table saws and panels saws- With thin kerf for less friction cuts- HW grade: HC10 (K10-C3)
Pin holes: PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
ART. CF
Item D d B/c Z Pin holes CF150.02430 150 30 2,2/1,6 24CF180.03030 180 30 2,2/1,6 30
CF200.03230 200 30 2,2/1,6 34CF250.04030 250 30 2,2/1,6 40 PH02
CF300.04830 300 30 2,2/1,6 48 PH02 CF350.05430 350 30 2,4/1,8 54 PH02
- For cutting along and across grain of softwood, rare woods and laminate boards
ART. CG
Item D d B/c Z Pin holes CG150.04830 150 30 2,2/1,6 48CG180.05630 180 30 2,2/1,6 56
CG200.06430 200 30 2,2/1,6 64CG250.08030 250 30 2,2/1,6 80 PH02
CG300.09630 300 30 2,2/1,6 96 PH02 CG350.10830 350 30 2,4/1,8 108 PH02
- For separating plastic up to 10 mm cutting height chipboards - For cutting along and across grain of fine wood, hardwood, single sided veneer boards and MDF
ART. CH
Item D d B/c Z Pin holes CH150.06030 150 30 2,2/1,6 60
CH200.08030 200 30 2,2/1,6 80CH250.10030 250 30 2,2/1,6 100 PH02
CH300.12030 300 30 2,2/1,6 120 PH02
- For cutting single sided veneer boards plastic and aluminium profiles, plexiglass, pertinax, hard paper and print boards
HW MULTI PURPOSE CIRCULAR SAWBLADES ART. DA
- FZ flat teeth - For cutting along grain of all natural woods with large cutting heights- For table saws- ♫ = no-noise- HW grade: HC10 (K10-C3)
Pin holes: PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
RPM suggested referred to the blade diameter
Item D d B/c Z Pin holes DA250.01830 ♫ 250 30 3,2/2,2 20 PH02
DA300.02030 ♫ 300 30 3,2/2,2 24 PH02DA300.02070 300 70+ch (21x84) 3,2/2,2 24 DA350.02430 ♫ 350 30 3,5/2,5 28 PH02
12.17
2019 - Sawblades
HW MULTI PURPOSE CIRCULAR SAWBLADES ART. DC
- WZ alternate top bevel teeth- Anti-kickback design- For cutting along and across grain of all natural woods, wooden boarding materials, also veneered or plastic coated one size
- For table saws- ♫ = no-noise- HW grade: HC10 (K10-C3)
Pin holes: PH01= 2/10/60 - PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
Item D d B/c Z Pin holes DC250.02430 ♫ 250 30 3,2/2,2 24 PH02
DC300.02830 ♫ 300 30 3,2/2,2 28 PH02DC315.02830 ♫ 315 30 3,2/2,2 28 PH02DC350.03230 ♫ 350 30 3,5/2,5 32 PH02
DC400.03630 ♫ 400 30 4,0/2,8 36 PH02 DC450.04030 450 30 4,2/2,8 40 PH01
DC500.04430 500 30 4,2/2,8 44 PH01DC550.04430 550 30 4,2/3,0 48 PH01
DC600.05430 600 30 4,2/3,0 48 PH01
RPM suggested referred to the blade diameter
The anti-kickback design reduces the amount of wood each tooth takes away. The wood worker understands the dangers of kick back.
HW RADIAL ARM SAWBLADES ART. FAS
Item D d B/c ZFAS300.03630 ♫ 300 30 4,4/2,8 36FAS350.04230 ♫ 350 30 4,4/2,8 42
FAS400.04830 ♫ 400 30 4,4/2,8 48
- WZ alternate top bevel teeth- 5° negative hook angle- For cutting across grain of soft wood, hard wood, aluminium-wood profiles, plastic-wood profiles
- For table saws- ♫ = no-noise- HW grade: HC10 (K10-C3)
RPM suggested referred to the blade diameter
HW TRIMMING AND SIZING SAWBLADESART. FB
Item D d B/c Z Pin holesFB220.04230 220 30 3,2/2,2 42FB253.04830 250 30 3,2/2,2 48 PH02
FB303.06030 300 30 3,2/2,2 60 PH02FB350.07230 350 30 3,5/2,5 72 PH02
- HZ/DZ inverted “V” and hollow ground teeth- For cutting boards with synthetic resincoating, double sided veneer and laminate boards and plywood
- For panel saws and table saws- Extra finish and long cutting life- HW grade: KCR06 (K01-C4)
Pin holes: PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
RPM suggested referred to the blade diameter
12.18
2019 - Sawblades
HW TRIMMING AND SIZING SAWBLADESART. FCS
Item D d B/c Z Pin holesFCS250.06030 ♫ 250 30 3,2/2,2 60 PH02FCS250.08030 ♫ 250 30 3,2/2,2 80 PH02
FCS300.07230 ♫ 300 30 3,2/2,2 72 PH02FCS300.09630 ♫ 300 30 3,2/2,2 96 PH02
FCS350.08430 ♫ 350 30 3,5/2,5 84 PH02FCS350.11230 ♫ 350 30 3,5/2,5 112 PH02
- FZ/TR triple chip teeth trapezoidal - For table saws- Ideal for working ALUCOBOND®- For cutting hardwoods, double sided veneer and laminate board, MDF, hard paper and thermoplastic boards
- Extra finish and long cutting life- ♫ = no-noise- HW grade: KCR06 (K01-C4)
Pin holes: PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
RPM suggested referred to the blade diameter
HW TRIMMING AND SIZING SAWBLADES “EXTRA CUT” ART. FCT
Item D d B/c Z Pin holesFCT250.06030 ♫ NEW 250 30 3,2/2,2 60 PH02FCT250.08030 ♫ NEW 250 30 3,2/2,2 80 PH02
FCT300.07230 ♫ NEW 300 30 3,2/2,2 72 PH02FCT300.09630 ♫ NEW 300 30 3,2/2,2 96 PH02
FCT350.08430 ♫ NEW 350 30 3,5/2,5 84 PH02FCT350.11230 ♫ NEW 350 30 3,5/2,5 112 PH02
- FZ/TR triple chip teeth trapezoidal - For cutting hardwoods, double sided veneer and laminate board, MDF, hard paper and thermoplastic boards
- Ideal for working ALUCOBOND®- For table saws- Extra finish and long cutting life- ♫ = no-noise and less vibration thanks to a special synthetic resin filled in the slots to increase the stability and reduce vibrations
- HW grade: KCR05 (K01-C4)
Pin holes: PH02=2/7/42 + 2/9,5/46,5 + 2/10/60
A NEW LEVEL OF CUTTING WITH SPECIAL SYNTHETIC RESIN FILLED IN THE SLOTS TO INCREASE THE STABILITY AND REDUCE VIBRATIONS
- LOW NOISE - NO VIBRATION- BETTER FINISHING- LONGER LIFE
12.19
2019 - Sawblades
HW MULTIRIP SAWBLADES WITHOUT RAKERSART. FE
Item D d+keyways B/c Z FE300.02870 300 70+ch (21x84) 3,2/2,2 24 FE300.02880 300 80+ch (13x90) 3,2/2,2 24
FE350.03270 350 70+ch (21x84) 3,5/2,5 28
- WZ alternate top bevel teeth- For cutting along grain of softwood, hardwood and exotic timber- For multi blades saws- HW grade: HC10 (K10-C3)
HW SHOULDER RIP SAWBLADES WITH RAKERSART. FG
Item D d+keyways B/c Z L maxFG300.02470 300 70+ch (21x84) 4,0/2,8 24+2+2 80FG300.02480 300 80+ch (13x90) 4,0/2,8 24+2+2 80
FG301.02470 300 70+ch (21x84) 5,2/3,6 24+2+2 80FG301.02475 300 75+ch (21x91) 5,2/3,6 24+2+2 80FG301.02480 300 80+ch (13x90) 5,2/3,6 24+2+2 80
FG320.02480 320 80+ch (13x90) 4,0/2,8 24+2+2 90
FG350.02470 350 70+ch (21x84) 4,2/2,8 24+2+4 105FG350.02475 350 75+ch (21x91) 4,2/2,8 24+2+4 105FG350.02480 350 80+ch (14x92) 4,2/2,8 24+2+4 105
FG351.02470 350 70+ch (21x84) 4,5/3,2 24+2+2 105FG351.02475 350 75+ch (21x91) 4,5/3,2 24+2+4 105 FG351.02480 350 80+ch (14x92) 4,5/3,2 24+2+4 105
FG352.02470 350 70+ch (21x84) 5,2/3,6 24+2+4 105FG352.02475 350 75+ch (21x91) 5,2/3,6 24+2+4 105FG352.02480 350 80+ch (14x92) 5,2/3,6 24+2+4 105
- WZ alternate teeth- With HW rakers for better result in cutting along grainof hard wood and rare wood
- For sizing and trimming- For multi blades saws- HW grade: HC10 (K10-C3)
RPM suggested referred to the blade diameter
Some tips for working with multi-ripping saws
A) When operating with a multi-rip saw the use of shouldersaw blades is very important (Items FG).Positioned as the first blade on the machine side they allow,especially during heavy-duty processing or working uneventimber, that the forces have a proper distribution.
B) The use of rakers is highly recommended to avoid the sawblade rubbing on the wood, causing overheating and frictionwhich can damage the saw blades.
C) If the machine spindle has only one keyway it is highlyrecommended not to use saw blades having two to avoid anyunbalanced coupling.
D) Keyways of the saw blades and machine spindle are bestcoupled when they have the same dimensions.
Outside raker
Keyways
Inside raker
Lmax= Max cutting length
Shoulder rip blade(Art. FG)
HW MULTIRIP SAWBLADES WITH RAKERSART. FH
Item D d+keyways B/c Z L maxFH250.01830 250 30 3,2/2,2 20+2+2 65 FH250.01860 250 60+ch (21x74) 3,2/2,2 20+2+2 65 FH250.01870 250 70+ch (21x84) 3,2/2,2 20+2+2 65 FH250.01880 250 80+ch (13x90) 3,2/2,2 20+2+2 65 FH280.02070 280 70+ch (21x84) 3,2/2,2 24+2+2 65 FH280.02080 280 80+ch (13x90) 3,2/2,2 24+2+2 70
FH300.02430 300 30 3,2/2,2 24+2+2 80 FH300.02460 300 60+ch (21x74) 3,2/2,2 24+2+2 80 FH300.02470 300 70+ch (21x84) 3,2/2,2 24+2+2 80 FH300.02475 300 75+ch (21x91) 3,2/2,2 24+2+2 80 FH300.02480 300 80+ch (13x90) 3,2/2,2 24+2+2 80 FH320.02480 320 80+ch (13x90) 3,5/2,5 24+2+2 90 FH350.02475 350 75+ch (21x91) 3,5/2,5 24+2+4 105 FH350.02480 350 80+ch (14x92) 3,5/2,5 24+2+4 105 FH350.02490 350 90+ch (21x110) 3,5/2,5 24+2+4 95 FH350.02630 350 30 3,5/2,5 24+2+4 105 FH350.02660 350 60+ch (21x74) 3,5/2,5 24+2+4 105 FH350.02870 350 70+ch (21x84) 3,5/2,5 24+2+4 105
FH400.02875 400 75+ch (21x91) 4,0/2,8 28+2+4 120 FH400.02880 400 80+ch (13x90) 4,0/2,8 28+2+4 120 FH400.03030 400 30 4,0/2,8 28+2+4 120 FH400.03070 400 70+ch (21x84) 4,0/2,8 28+2+4 120
FH450.02430 450 30 4,6/3,2 24+2+4 135FH450.02470 450 70+ch (21x84) 4,6/3,2 24+2+4 135FH450.02475 450 75+ch (21x91) 4,6/3,2 24+2+4 135 FH450.02480 450 80+ch (13x92) 4,6/3,2 24+2+4 135FH450.02490 450 90+ch (21x110) 4,6/3,2 24+2+4 135
FH500.02630 500 30 4,6/3,2 26+2+6 175
- WZ alternate top bevel teeth- With HW outside and inside rakers for better result in cutting- For cutting along grain of softwood and hardwood dried at 15% humidity rate, exotic timber and rare wood
- HW grade: HC10 (K10-C3)
On request we can also supply multirip sawblades for “RAIMANN” machines.
HW MULTIRIP SAWBLADES WITH RAKERS (THIN KERF)ART. FK
Item D d+keyways B/c Z L maxFK180.02135 180 35 2,5/1,8 21+3 30 FK180.02140 180 40 2,5/1,8 21+3 30
FK200.02135 200 35 2,5/1,8 21+3 35 FK200.02140 200 40 2,5/1,8 21+3 35
FK250.02060 250 60+ch (21x74) 2,7/1,8 20+2+2 50 FK250.02070 250 70+ch (21x84) 2,7/1,8 20+2+2 50 FK250.02080 250 80+ch (13x90) 2,7/1,8 20+2+2 50
FK300.02460 300 60+ch (21x74) 2,7/1,8 24+2+2 60 FK300.02470 300 70+ch (21x84) 2,7/1,8 24+2+2 60 FK300.02480 300 80+ch (13x90) 2,7/1,8 24+2+2 60
- FZ flat teeth - With HW outside and inside rakers for better result in cutting- For cutting along grain of softwood and hardwood dried at 10%-15% humidity rate, exotic timber and rare wood
- Suitable for ripping where its thin body greatly reduces material wastes- Ideal for processing wooden floors and matchboardings- HW grade: HC10 (K10-C3)
12.20
2019 - Sawblades
RPM suggested referred to the blade diameter
Lmax= Max cutting length
RPM suggested referred to the blade diameter
Scale 1:1
Scale 1:1
Pin holes for sizing sawblades:
PH02
12.21
2019 - Sawblades
PH04
Name Nr of holes/diameter of holes/pitch circle diameter Machine typePH02 2/7/42 + 2/9,5/46,5 + 2/10/60 Universal
Name Nr of holes/diameter of holes/pitch circle diameter Machine typePH04 2/14/110 + 2/7/110 + 4/9/100 + 4/19/120 + 2/9/130 GABBIANI - SCM - SELCO
PH05Scale 1:1
12.22
2019 - Sawblades
Name Nr of holes/diameter of holes/pitch circle diameter Machine typePH05 4/15/105 + 3/7/100 GIBEN - HOMAG - MACMAZZA
12.23
2019 - Sawblades
REFERENCE TABLE OF PANEL SIZING MACHINES
Item D B d Z MAT.HCS400.07260 400 4.4/3.2 60+2 72 FZ/TR HW HCS430.07260 430 4.4/3.2 60+2 72 FZ/TR HWHCS450.07260 450 4.4/3.2 60+2 72 FZ/TR HWHCS531.06060 530 5.8/4.0 60+2 60 FZ/TR HW
XHC400.07260 400 4.4/3.2 60+2 72 FZ/TR DPPin holes 2/11/85
ANTHON: MAIN SAWBLADE
Item D B d Z MAT.HCS300.06080 300 4.4/3.2 80+PH4 60 FZ/TR HW HCS300.07280 300 4.4/3.2 80+PH4 72 FZ/TR HWHCS350.05680 350 4.4/3.2 80+PH4 54 FZ/TR HWHCS350.07280 350 4.4/3.2 80+PH4 72 FZ/TR HWHCS351.07280 350 4.6/3.2 80+PH4 72 FZ/TR HWHCS355.07280 350 4.4/3.2 80+PH4 72 FZ/TR HWHCS380.07280 380 4.4/3.2 80+PH4 72 FZ/TR HWHCS400.06080 400 4.4/3.2 80+PH4 60 FZ/TR HWHCS400.07280 400 4.4/3.2 80+PH4 72 FZ/TR HWHCS401.07280 400 4.6/3.2 80+PH4 72 FZ/TR HWHCS420.07280 420 4.4/3.2 80+PH4 72 FZ/TR HWHCS450.07280 450 4.4/3.2 80+PH4 72 FZ/TR HW
HBS350.05680 350 4.4/3.2 80+PH4 54 WZ HWHBS350.07280 350 4.4/3.2 80+PH4 72 WZ HWHBS400.03680 400 4.4/3.2 80+PH4 36 WZ HWHBS400.06080 400 4.4/3.2 80+PH4 60 WZ HWHBS400.07280 400 4.4/3.2 80+PH4 72 WZ HWHBS401.06080 400 4.6/3.2 80+PH4 60 WZ HWHBS450.03680 450 4.4/3.2 80+PH4 36 WZ HWHBS450.05480 450 4.4/3.2 80+PH4 54 WZ HW
XHC350.07280 350 4.4/3.2 80+PH4 72 FZ/TR DPXHC400.07280 400 4.4/3.2 80+PH4 72 FZ/TR DPXHC450.07280 450 4.4/3.2 80+PH4 72 FZ/TR DPPin holes 2/14/110+2/7/110+4/9/100
GABBIANI:MAIN SAWBLADE
Item D B d Z MAT.FI180.03620 180 4.3/5.5 20 36 KON/FZ HW FI183.03620 180 5.8/7.0 20 36 KON/FZ HW
XFI180.03620 180 4.4/5.0 20 36 KON/FZ DP XFI182.03620 180 5.8/6.6 20 36 KON/FZ DP
ANTHON: SCORING SAWBLADE
Item D B d Z MAT.FI161.03655 160 4.3/5.5 55+3 36 KON/FZ HWFI162.03655 160 4.5/5.7 55+3 36 KON/FZ HWFI163.03655 160 4.7/6.0 55+3 36 KON/FZ HWFI200.03680 200 4.3/5,5 80 36 KON/FZ HWPin holes 2/14/110XFI160.03655 160 4.4/5.0 55+3 36 KON/FZ DP Pin holes 3/7/66
GABBIANI: SCORING SAWBLADE
Item D B d Z MAT.HCS320.06050 320 4.4/3.2 50+8 60 FZ/TR HW HCS320.07250 320 4.4/3.2 50+8 72 FZ/TR HWHCS330.06050 330 4.4/3.2 50+8 60 FZ/TR HWHCS350.07250 350 4.4/3.2 50+8 72 FZ/TR HWHCS360.07250 360 4.4/3.2 50+8 72 FZ/TR HWHCS380.07250 380 4.4/3.2 50+8 72 FZ/TR HW
HBS320.03650 320 4.4/3.2 50+8 36 WZ HW
XHC320.06050 320 4.4/3.2 50+8 60 FZ/TR DPXHC330.06050 330 4.4/3.2 50+8 60 FZ/TR DPXHC350.07250 350 4.4/3.2 50+8 72 FZ/TR DPXHC360.07250 360 4.4/3.2 50+8 72 FZ/TR DPPin holes 6/12.5/80+2/12.5/80
HCS320.07275 320 4.4/3.2 75+3 72 FZ/TR HWPin holes 3/13/95
HCS350.05675 350 4.4/3.2 75+PH5 54 FZ/TR HWHCS350.07275 350 4.4/3.2 75+PH5 72 FZ/TR HWHCS355.07275 355 4.4/3.2 75+PH5 72 FZ/TR HWHCS380.07250 380 4.4/3.2 75+PH5 72 FZ/TR HWHCS400.06075 400 4.4/3.2 75+4 60 FZ/TR HW HCS400.07275 400 4.4/3.2 75+4 72 FZ/TR HWHCS430.07275 430 4.4/3.2 75+4 72 FZ/TR HWHCS430.09675 430 4.4/3.2 75+4 96 FZ/TR HWHCS470.07275 470 4.4/3.2 75+4 72 FZ/TR HWHCS470.09675 470 4.4/3.2 75+4 96 FZ/TR HW
HBS350.05675 350 4.4/3.2 75+PH5 54 WZ HWHBS350.07275 350 4.4/3.2 75+PH5 72 WZ HWHBS400.06075 400 4.4/3.2 75+4 60 WZ HWHBS400.07275 400 4.4/3.2 75+4 72 WZ HWHBS401.06075 400 4.6/3.2 75+4 60 WZ HW
XHC350.07275 350 4.4/3.2 75+4 72 FZ/TR DPXHC400.07275 400 4.4/3.2 75+4 72 FZ/TR DPXHC430.07275 430 4.4/3.2 75+4 72 FZ/TR DPXHC470.07275 470 4.4/3.2 75+4 72 FZ/TR DPPin holes 4/15/105
HCS550.07299 550 5.2/3.5 100 72 FZ/TR HWHCS565.07299 565 5.2/3.5 100 72 FZ/TR HW
GIBEN : MAIN SAWBLADE
Item D B d Z MAT.FL127.02045 125 4.0/4.8 45 20+20 KON/FZ HW FI126.02445 125 4.3/5.5 45 24 KON/FZ HWXFI126.02045 125 4.0/4.8 45 20+20 KON/FZ DP FI161.03645 160 4.3/5.5 45+3 36 KON/FZ HWFI162.03645 160 4.5/5.7 45+3 36 KON/FZ HW
XFI160.03645 160 4.4/5.0 45+3 36 KON/FZ DP Pin holes 3/11/70
FI180.03650 180 4.3/5.5 50+3 44 KON/FZ HW
XFI180.04450 180 4.4/5.0 50+3 44 KON/FZ DP Pin holes 3/12.5/80
FI182.03655 180 5.0/6.2 55 36 KON/FZ HW
FI215.04250 215 4.3/5.5 50+3 42 KON/FZ HWFI216.04250 215 4.5/5.7 50+3 42 KON/FZ HWFI300.04850 300 4.3/5.5 50+3 48 KON/FZ HWFI301.04850 300 4.5/5.7 50+3 48 KON/FZ HW
XFI215.04250 215 4.4/5.0 50+3 42 KON/FZ DP Pin holes 3/15/80
GIBEN: SCORING SAWBLADE
12.24
2019 - Sawblades
Item D B d Z MAT.HCS350.07260 350 4.4/3.2 60+2 72 FZ/TR HW HCS380.07260 380 4.4/3.2 60+2 72 FZ/TR HWHCS381.06050 380 4.8/3.5 60+2 72 FZ/TR HWHCS381.08460 380 4.8/3.5 60+2 84 FZ/TR HW
XHC350.07260 350 4.4/3.2 60+2 72 FZ/TR DPXHC380.07260 380 4.8/3.5 60+2 72 FZ/TR DPPin holes 2/14/100
HCS402.07260 400 4.8/3.5 60+4 72 FZ/TR HW
XHC401.07260 400 4.8/3.5 60+4 72 FZ/TR DPPin holes 2/14/100+2/14/125
HCS421.07260 420 4.8/3.5 60+2 72 FZ/TR HWHCS450.07260 450 4.4/3.2 60+2 72 FZ/TR HWHCS452.07260 450 4.8/3.5 60+2 72 FZ/TR HW
XHC420.07260 420 4.8/3.5 60+2 72 FZ/TR DPXHC451.07260 450 4.8/3.5 60+2 72 FZ/TR DPPin holes 2/14/125
HCS500.06060 500 4.8/3.5 60+2 60 FZ/TR HWHCS500.07260 500 4.8/3.5 60+2 72 FZ/TR HW
XHC500.07260 500 4.8/3.5 60+2 72 FZ/TR DPPin holes 2/11/115
HCS481.07260 480 4.8/3.5 60+4 72 FZ/TR HWHCS520.06060 520 4.8/3.5 60+4 60 FZ/TR HWHCS540.08460 540 4.8/3.5 60+4 84 FZ/TR HWHCS541.06060 540 5.8/4.0 60+4 60 FZ/TR HWHCS570.06060 570 4.8/3.5 60+4 60 FZ/TR HWHCS571.09660 570 5.8/4.0 60+4 96 FZ/TR HWHCS600.06060 600 5.8/4.0 60+4 60 FZ/TR HWHCS600.07260 600 5.8/4.0 60+4 72 FZ/TR HW
XHC481.07260 480 4.8/3.5 60+4 72 FZ/TR DPXHC520.06060 520 4.8/3.5 60+4 60 FZ/TR DPPin holes 2/11/115+2/19/120
HOLZMA:MAIN SAWBLADE
Item D B d Z MAT.FI180.03645 180 4.3/5.5 45 36 KON/FZ HWFI181.03645 180 4.7/6.0 45 36 KON/FZ HWFI200.03645 200 4.3/5.5 45 36 KON/FZ HWFI201.03645 200 4.7/6.0 45 36 KON/FZ HWFI204.03645 200 5.8/7.0 45 36 KON/FZ HW
XFI180.03645 180 4.4/5.0 45 36 KON/FZ DP XFI181.03645 180 4.8/5.6 45 36 KON/FZ DP XFI200.03645 200 4.4/5.0 45 36 KON/FZ DP XFI201.03645 200 4.8/5.6 45 36 KON/FZ DP XFI203.03645 200 5.8/6.6 45 36 KON/FZ DP
GIBEN: SCORING SAWBLADE
Item D B d Z MAT.HCS300.06075 300 4.4/3.2 75 60 FZ/TR HW HCS350.05675 350 4.4/3.2 75 54 FZ/TR HWHCS350.07275 350 4.4/3.2 75 72 FZ/TR HWHCS355.07275 355 4.4/3.2 75 72 FZ/TR HWHCS400.06075 400 4.4/3.2 75 60 FZ/TR HWHCS400.07275 400 4.4/3.2 75 72 FZ/TR HW
HBS350.05675 350 4.4/3.2 75 54 WZ HWHBS350.07275 350 4.4/3.2 75 72 WZ HWHBS400.06075 400 4.4/3.2 75 60 WZ HWHBS400.07275 400 4.4/3.2 75 72 WZ HWHBS401.06075 400 4.6/3.2 75 60 WZ HW
XHC350.07275 350 4.4/3.2 75 72 FZ/TR DPXHC400.07275 400 4.4/3.2 75 72 FZ/TR DP
HOMAG:MAIN SAWBLADE
Item D B d Z MAT.FI126.02445 125 4.3/5.5 45 24 KON/FZ HWFI151.03645 150 4.3/5.5 45 36 KON/FZ HWFI180.03645 180 4.3/5.5 45 36 KON/FZ HWFI200.03645 200 4.3/5.5 45 36 KON/FZ HW
XFI160.03645 160 4.4/5.0 45 36 KON/FZ DP XFI180.03645 180 4.4/5.0 45 36 KON/FZ DP XFI200.03645 200 4.4/5.0 45 36 KON/FZ DP
HOMAG: SCORING SAWBLADE
Item D B d Z MAT.HCS350.05675 350 4.4/3.2 75+3 54 FZ/TR HW HCS350.07275 350 4.4/3.2 75+3 72 FZ/TR HWHCS355.07275 355 4.4/3.2 75+3 72 FZ/TR HWHCS380.07275 380 4.4/3.2 75+3 72 FZ/TR HW
HBS350.05675 350 4.4/3.2 75+3 54 WZ HWHBS350.07275 350 4.4/3.2 75+3 72WZ HW
XHC350.07275 350 4.4/3.2 75+3 72 FZ/TR DPPin holes 3/7/100
HCS450.07275 450 4.4/3.2 75+3 72 FZ/TR HW Pin holes 3/7/120
MACMAZZA:MAIN SAWBLADE
Articolo D B d Z MAT.FI161.03655 160 4.3/5.5 55+3 36 KON/FZ HWFI280.04855 280 4.5/5.6 55+3 48 KON/FZ HW
XFI160.03645 160 4.4/5.0 55+3 36 KON/FZ DP Pin holes 3/6/84
MACMAZZA: SCORING SAWBLADE
Item D B d Z MAT.HCS300.06030 300 4.4/3.2 30+PH1 60 FZ/TR HW HCS300.07230 300 4.4/3.2 30+PH1 72 FZ/TR HWHCS350.05630 350 4.4/3.2 30+PH1 54 FZ/TR HWHCS350.07230 350 4.4/3.2 30+PH1 72 FZ/TR HWHCS400.06030 400 4.4/3.2 30+2 60 FZ/TR HWHCS400.07230 400 4.4/3.2 30+2 72 FZ/TR HW
HBS300.04830 300 4.4/3.2 30+PH1 48A HWHBS300.06030 300 4.4/3.2 30+PH1 60A HWHBS300.07230 300 4.4/3.2 30+PH1 72A HWHBS350.05430 350 4.4/3.2 30+PH1 54A HWHBS350.07230 350 4.4/3.2 30+PH1 72A HWHBS400.06030 400 4.4/3.2 30+2 60A HWHBS400.07230 400 4.4/3.2 30+2 72A HW
XHC300.06030 300 4.4/3.2 30+PH1 60 FZ/TR DPXHC350.07230 350 4.4/3.2 30+PH1 72 FZ/TR DPXHC400.07230 400 4.4/3.2 30+2 72 FZ/TR DPPin holes 2/10/60
MAYER: MAIN SAWBLADE
Item D B d Z MAT.HCS300.06030 300 4.4/3.2 30+PH1 60 FZ/TR HW HCS300.07230 300 4.4/3.2 30+PH1 72 FZ/TR HWHCS350.05430 350 4.4/3.2 30+PH1 54 FZ/TR HWHCS350.07230 350 4.4/3.2 30+PH1 72 FZ/TR HWHCS400.06030 400 4.4/3.2 30+PH1 60 FZ/TR HWHCS400.07230 400 4.4/3.2 30+PH1 72 FZ/TR HWHCS450.07230 450 4.4/3.2 30+2 72 FZ/TR HW
HBS300.04830 300 4.4/3.2 30+PH1 48 WZ HWHBS300.06030 300 4.4/3.2 30+PH1 60 WZ HWHBS300.07230 300 4.4/3.2 30+PH1 72 WZ HWHBS350.05430 350 4.4/3.2 30+PH1 54 WZ HWHBS350.07230 350 4.4/3.2 PH2 72 WZ HWHBS400.06030 400 4.4/3.2 30+2 60 WZ HWHBS400.07230 400 4.4/3.2 30+2 72 WZ HWHBS450.05430 450 4.4/3.2 30+2 54 WZ HWHBS450.07230 450 4.4/3.2 30+2 72 WZ HW
XHC300.06030 300 4.4/3.2 30+PH1 60 FZ/TR DPXHC350.07230 350 4.4/3.2 30+PH1 72 FZ/TR DPXHC400.07230 400 4.4/3.2 30+2 72 FZ/TR DPPin holes 2/10/60
PANHANS:MAIN SAWBLADE
Item D B d Z MAT.FL127.02045 125 4.0/4.8 45 20+20 KON/FZ HWFI126.02445 125 4.3/5.5 45 24 KON/FZ HWFI151.03630 150 4.3/5.5 30 36 KON/FZ HW
XFI126.02045 125 4.0/4.8 45 20+20 KON/FZ DP
MAYER: SCORING SAWBLADE
Item D B d Z MAT.FI126.02420 125 4.3/5.5 20 24 KON/FZ HWFI180.03630 180 4.3/5.5 30 36 KON/FZ HWFI200.03630 200 4.3/5.5 30 36 KON/FZ HW
XFI200.03630 200 4.4/5.0 30 36 KON/FZ DP
PANHANS: SCORING SAWBLADE
12.25
2019 - Sawblades
Item D B d Z MAT.HCS350.05630 350 4.4/3.2 30+PH1 54 FZ/TR HW HCS350.07230 350 4.4/3.2 30+PH1 72 FZ/TR HWHCS370.07230 370 4.4/3.2 30+2 72 FZ/TR HWHCS400.06030 400 4.4/3.2 30+PH1 60 FZ/TR HWHCS400.07230 400 4.4/3.2 30+PH1 72 FZ/TR HW
HBS350.05430 350 4.4/3.2 30+PH1 54 WZ HWHBS350.07230 350 4.4/3.2 30+PH1 72 WZ HWHBS400.06030 400 4.4/3.2 30+2 60 WZ HWHBS400.07230 400 4.4/3.2 30+2 72 WZ HW
XHC300.06030 300 4.4/3.2 30+PH1 60 FZ/TR DPXHC350.07230 350 4.4/3.2 30+PH1 72 FZ/TR DPXHC370.07230 370 4.4/3.2 30+2 72 FZ/TR DPXHC400.07230 400 4.4/3.2 30+2 72 FZ/TR DPPin holes 2/10/60
HCS450.07230 450 4.4/3.2 30+2 72 FZ/TR HW HCS460.07230 460 4.4/3.2 30+2 72 FZ/TR HWHCS480.07230 480 4.4/3.2 30+2 72 FZ/TR HWHCS500.07230 500 4.6/3.2 30+2 72 FZ/TR HWHCS520.07230 520 4.8/3.5 30+2 72 FZ/TR HW HCS530.06030 530 5.0/3.5 30+2 60 FZ/TR HW
HBS450.05430 450 4.4/3.2 30+2 54 WZ HWHBS450.05430 450 4.4/3.2 30+2 72 WZ HWHBS500.07230 500 4.6/3.2 30+2 72 WZ HW
XHC450.07230 450 4.4/3.2 30+2 72 FZ/TR DPXHC460.07230 460 4.4/3.2 30+2 72 FZ/TR DPXHC480.07230 480 4.4/3.2 30+2 72 FZ/TR DPPin holes 2/13/94
HCS550.06040 550 5.2/3.5 40+2 60 FZ/TR HW Pin holes 2/13/122
SCHELLING:MAIN SAWBLADE
Item D B d Z MAT.FI180.03630 180 4.3/5.5 20 36 KON/FZ HWFI200.03620 200 4.3/5.5 20 36 KON/FZ HWFI203.03620 200 5.0/6.2 20 36 KON/FZ HW
XFI180.03620 180 4.4/5.0 20 36 KON/FZ DP XFI200.03620 200 4.4/5.0 20 36 KON/FZ DP XFI201.03620 200 5.0/5.8 20 36 KON/FZ DP
SCHELLING: SCORING SAWBLADE
12.26
2019 - Sawblades
Item D B d Z MAT.FI151.03655 150 4.3/5.5 55+3 36 KON/FZ HWFI161.03655 160 4.3/5.5 55+3 36 KON/FZ HWFI162.03655 160 4.5/5.7 55+3 36 KON/FZ HW
XFI160.03645 160 4.4/5.0 55+3 36 KON/FZ DP Pin holes 3/7/66
SCM: SCORING SAWBLADE
Item D B d Z MAT.HCS300.06080 300 4.4/3.2 80+PH4 60 FZ/TR HW HCS300.07280 300 4.4/3.2 80+PH4 72 FZ/TR HWHCS350.05680 350 4.4/3.2 80+PH4 54 FZ/TR HWHCS350.07280 350 4.4/3.2 80+PH4 72 FZ/TR HWHCS351.07280 350 4.6/3.2 80+PH4 72 FZ/TR HWHCS355.07280 355 4.4/3.2 80+PH4 72 FZ/TR HWHCS380.07280 380 4.4/3.2 80+PH4 72 FZ/TR HWHCS400.06080 400 4.4/3.2 80+PH4 60 FZ/TR HW HCS400.07280 400 4.4/3.2 80+PH4 72 FZ/TR HWHCS401.07280 400 4.6/3.2 80+PH4 72 FZ/TR HW
HBS350.05680 350 4.4/3.2 80+PH4 54 WZ HWHBS350.07280 350 4.4/3.2 80+PH4 72 WZ HWHBS400.03680 400 4.4/3.2 80+PH4 36 WZ HWHBS400.04880 400 4.4/3.2 80+PH4 48 WZ HWHBS400.06080 400 4.4/3.2 80+PH4 60 WZ HWHBS400.07280 400 4.4/3.2 80+PH4 72 WZ HWHBS401.06080 400 4.6/3.2 80+PH4 60 WZ HWHBS450.03680 450 4.4/3.2 80+PH4 36 WZ HWHBS450.05480 450 4.4/3.2 80+PH4 54 WZ HW
XHC350.07280 350 4.4/3.2 80+PH4 72 FZ/TR DPXHC400.07280 400 4.4/3.2 80+PH4 72 FZ/TR DPXHC450.07280 450 4.4/3.2 80+PH4 72 FZ/TR DPPin holes 2/14/110+2/7/110+4/9/100
SCM:MAIN SAWBLADE
Item D B d Z MAT.HCS300.06065 300 4.4/3.2 65+4 60 FZ/TR HW HCS300.07265 300 4.4/3.2 65+4 72 FZ/TR HWHCS320.06065 320 4.4/3.2 65+4 60 FZ/TR HWHCS321.06065 320 4.6/3.2 65+4 60 FZ/TR HWHCS350.07265 350 4.4/3.2 65+4 72 FZ/TR HWHCS361.07265 360 4.6/3.2 65+4 72 FZ/TR HW
XHC300.06065 300 4.4/3.2 65+4 60 FZ/TR DPXHC320.06065 320 4.4/3.2 65+4 60 FZ/TR DPXHC350.07265 350 4.4/3.2 65+4 72 FZ/TR DPXHC360.07265 360 4.4/3.2 65+4 72 FZ/TR DPPin holes 2/9/100+2/9/110
HCS350.05680 350 4.4/3.2 80+PH4 54 FZ/TR HW HCS350.07280 350 4.4/3.2 80+PH4 72 FZ/TR HWHCS351.07280 350 4.6/3.2 80+PH4 72 FZ/TR HWHCS355.07280 355 4.4/3.2 80+PH4 72 FZ/TR HWHCS400.06080 400 4.4/3.2 80+PH4 60 FZ/TR HWHCS400.07280 400 4.4/3.2 80+PH4 72 FZ/TR HWHCS401.07280 400 4.6/3.2 80+PH4 72 FZ/TR HW HCS430.07280 430 4.4/3.2 80+PH4 72 FZ/TR HWHCS450.07280 450 4.4/3.2 80+PH4 72 FZ/TR HWHCS451.07280 450 4.6/3.2 80+PH4 72 FZ/TR HWHCS452.07280 450 4.8/3.5 80+PH4 72 FZ/TR HWHCS481.07280 480 4.8/3.5 80+6 72 FZ/TR HWHCS482.07280 480 5.2/3.5 80+6 72 FZ/TR HW
HBS350.05480 350 4.4/3.2 80+PH4 54 WZ HW HBS350.07280 350 4.4/3.2 80+PH4 72 WZ HWHBS400.03680 400 4.4/3.2 80+PH4 36 WZ HWHBS400.04880 400 4.4/3.2 80+PH4 48 WZ HWHBS400.06080 400 4.4/3.2 80+PH4 60 WZ HW HBS400.07280 400 4.4/3.2 80+PH4 72 WZ HW HBS401.06080 400 4.6/3.2 80+PH4 60 WZ HW HBS450.03680 450 4.4/3.2 80+PH4 36 WZ HWHBS450.05480 450 4.4/3.2 80+PH4 54 WZ HWHBS451.04880 450 4.8/3.5 80+PH4 48 WZ HW
XHC350.07280 350 4.4/3.2 80+PH4 72 FZ/TR DPXHC400.07280 400 4.4/3.2 80+PH4 72 FZ/TR DPXHC430.07280 430 4.4/3.2 80+PH4 72 FZ/TR DPXHC450.07280 450 4.4/3.2 80+PH4 72 FZ/TR DPXHC451.07280 450 4.8/3.5 80+PH4 72 FZ/TR DPXHC481.07280 480 4.8/3.5 80+6 72 FZ/TR DPPin holes 4/19/120+2/9/130
SELCO:MAIN SAWBLADE
Item D B d Z MAT.FI200.03665 200 4.3/5.5 65+4 36 KON/FZ HWFI201.03665 200 4.7/6.0 65+4 36 KON/FZ HWFI202.03665 200 4.5/5.7 65+4 36 KON/FZ HWFI203.03665 200 5.0/6.2 65+4 36 KON/FZ HWFI300.07265 300 4.3/5.5 65+4 72 KON/FZ HWFI301.07265 300 4.5/5.7 65+4 72 KON/FZ HWFI302.07265 300 4.7/6.0 65+4 72 KON/FZ HW
XFI200.03665 200 4.4/5.0 65+4 36 KON/FZ DPXFI200.03645 200 4.8/5.6 65+4 36 KON/FZ DP Pin holes 2/9/100+2/9/110
SELCO: SCORING SAWBLADE
12.27
2019 - Sawblades
HW CONICAL SCORING SAWBLADESART. FI
Item D d B-B1/c Z MachingFI080.01220 80 20 3,1-4,0/2,2 12 Casadei
FI100.02020 100 20 3,1-4,3/2,2 20 FI100.02022 100 22 3,1-4,3/2,2 20
FI110.02020 110 20 3,1-4,3/2,2 20 FI110.02022 110 22 3,1-4,3/2,2 20
FI120.02420 120 20 3,1-4,3/2,2 20 FI120.02422 120 22 3,1-4,3/2,2 20
FI121.02445 selling out 120 45 4,3-5,5/2,8 24
FI122.02020 120 20 3,4-4,5/2,2 20 SCM
FI125.02420 125 20 3,1-4,3/2,2 24 Panhans-Schelling FI125.02445 125 45 3,1-4,3/2,2 24
FI126.02420 125 20 4,3-5,5/3,2 24 Panhans-Gabbiani FI126.02422 125 22 4,3-5,5/3,2 24FI126.02445 125 45 4,3-5,5/3,2 24 Giben-Homag
FI127.02420 125 20 3,4-4,5/2,2 24 FI127.02430 125 30 3,4-4,5/2,2 24
FI150.03630 150 30 3,4-4,5/2,2 36 SCM
FI150.03645 selling out 150 45 3,4-4,5/2,2 36FI150.03650 selling out 150 50 3,4-4,5/2,2 36
FI151.02430 150 30 4,3-5,5/3,2 24FI151.02445 150 45 4,3-5,5/3,2 24FI151.03630 150 30 4,3-5,5/3,2 36 SCM-Verry
FI151.03645 150 45 4,3-5,5/3,2 36 Giben-SCM-Holzma-Homag
FI151.03655 150 55 4,3-5,5/3,2 36 Gabbiani
FI152.03630 150 30 3,9-5,1/2,8 36
FI153.03630 150 30 3,1-4,3/2,2 36 SCM
- KON/FZ conical teeth- For cutting double sided veneer and laminate boards, MDF and particle board- To be used on panel sizing machines that allow the vertical adjustment of the scorer in relation to the panel sizing sawblade
- HW grade: KCR05 (K01-C4)
Item D d B-B1/c Z MachingFI161.02430 160 30 4,3-5,5/3,2 36 Langzauner
FI161.03620 160 20 4,3-5,5/3,2 36FI161.03645 160 45 4,3-5,5/3,2 36 Giben
FI161.03655 160 55 4,3-5,5/3,2 36 MacMazza-Gabbiani-SCM
FI162.03645 160 45 4,5-5,7/3,2 36 Giben
FI162.03655 160 55 4,5-5,7/3,2 36 Gabbiani
FI163.03655 160 55 4,7-6,0/3,5 36 Gabbiani
FI180.03620 180 20 4,3-5,5/3,2 36 Schelling-Anthon
FI180.03630 180 30 4,3-5,5/3,2 36 2/10/60
FI180.03650 180 50 4,3-5,5/3,2 44 Giben
FI180.03645 180 45 4,3-5,5/3,2 36 Holzma
FI180.03655 180 55 4,3-5,5/3,2 36 Giben
FI181.03645 180 45 4,7-6,0/3,5 36 Holzma
FI182.03655 180 55 5,0-6,2/3,5 36 Giben
FI183.03620 180 20 5,8-7,0/4,0 36 Anthon-Holzma
FI200.03620 200 20 4,3-5,5/3,2 36 Schelling
FI200.03630 200 30 4,3-5,5/3,2 36 Scheer
FI200.03645 200 45 4,3-5,5/3,2 36 Holzma
FI200.03665 200 65 4,3-5,5/3,2 36 Selco
FI200.03680 200 80 4,3-5,5/3,2 36 Gabbiani
FI201.03645 200 45 4,7-6,0/3,5 36 Holzma
FI201.03665 200 65 4,7-6,0/3,5 36 Selco
FI202.03665 200 65 4,5-5,7/3,2 36 Selco
FI203.03665 200 65 5,0-6,2/3,5 36 Selco
FI204.03645 200 45 5,8-7,0/4,0 36 Holzma
FI215.04250 215 50 4,3-5,5/3,2 42 Giben
FI216.04250 215 50 4,5-5,7/3,2 42 Giben
FI280.04855 280 55 4,5-5,6/3,2 48 MacMazza
FI300.04850 300 50 4,3-5,5/3,2 48 Giben
FI300.07265 300 65 4,3-5,5/3,2 72 Selco
FI301.04850 300 50 4,5-5,7/3,2 48 Giben
FI301.07265 300 65 4,5-5,7/3,2 72 Selco
FI302.07265 300 65 4,7-6,0/3,5 72 Selco
12.28
2019 - Sawblades
HW ADJUSTABLE SCORING SAWBLADESART. FL
Item D d B/c Z Maching FL080.01020 80 20 2,8-3,6/2,2 10+10 Robland
FL100.01220 100 20 2,8-3,6/2,2 10+10 Schelling-Martin-Panhans FL100.01222 100 22 2,8-3,6/2,2 10+10 Altendorf-Striebig-Panhans
FL101.01220 100 20 3,1-3,9/2,2 10+10 FL101.01222 100 22 3,1-3,9/2,2 10+10
FL120.01220 120 20 2,8-3,6/2,2 12+12 Holzher-SCM FL120.01222 120 22 2,8-3,6/2,2 12+12 Altendorf-Martin-Mrozek
FL121.01220 120 20 3,1-3,9/2,2 12+12 FL121.01222 120 22 3,1-3,9/2,2 12+12
FL125.01220 125 20 2,8-3,6/2,2 12+12 Paoloni FL125.01222 125 22 2,8-3,6/2,2 12+12
FL126.01220 125 20 3,1-3,9/2,2 12+12FL126.01222 125 22 3,1-3,9/2,2 12+12FL126.01230 125 30 3,1-3,9/2,2 12+12
FL127.02045 125 45 4,0-4,8/2,2 20+20 Giben
HW adjustable scoring sawblades unit without ringsFL120.01250AN 120 50+4 2,8-3,8/2,2 12+12
- LFZ flat teeth- Supplied with spacers- For cutting double sided veneer and laminate boards, MDF and particle board- For panel sizing machines- HW grade: KCR05 (K01-C4)
HW PANEL SIZING SAWBLADESART. HBS
Item D d B/c Z Pin holesHBS300.04830 ♫ 300 30 4,4/3,2 48 PH02 HBS300.06030 ♫ 300 30 4,4/3,2 60 PH02 HBS300.07230 ♫ 300 30 4,4/3,2 72 PH02
HBS320.03650 ♫ 320 50 4,4/3,2 36 Giben
HBS350.05630 ♫ 350 30 4,4/3,2 54 PH02 HBS350.05675 ♫ 350 75 4,4/3,2 54 PH05 HBS350.05680 ♫ 350 80 4,4/3,2 54 PH04 HBS350.07230 ♫ 350 30 4,4/3,2 72 PH02 HBS350.07275 ♫ 350 75 4,4/3,2 72 PH05 HBS350.07280 ♫ 350 80 4,4/3,2 72 PH04
HBS400.03630 ♫ 400 30 4,4/3,2 36 PH01 HBS400.03680 ♫ 400 80 4,4/3,2 36 PH04 HBS400.06030 ♫ 400 30 4,4/3,2 60 PH01 HBS400.06075 ♫ 400 75 4,4/3,2 60 Giben-Homag HBS400.06080 ♫ 400 80 4,4/3,2 60 PH04 HBS400.07230 ♫ 400 30 4,4/3,2 72 PH01 HBS400.07275 ♫ 400 75 4,4/3,2 72 Giben-Homag HBS400.07280 ♫ 400 80 4,4/3,2 72 PH04
HBS401.06075 ♫ 400 75 4,6/3,2 60 Giben-HomagHBS401.06080 ♫ 400 80 4,6/3,2 60 PH04
HBS450.03680 ♫ 450 80 4,4/3,2 36 PH04HBS450.05430 ♫ 450 30 4,4/3,2 54 PH01 +SchellingHBS450.05480 ♫ 450 80 4,4/3,2 54 PH04HBS450.07230 ♫ 450 30 4,4/3,2 72 PH01 +Schelling
HBS451.04880 ♫ 450 80 4,8/3,5 48 PH04
HBS500.07230 ♫ 500 30 4,6/3,2 72 PH01 +Schelling
- WZ alternate top bevel teeth- For cutting double sided veneer and laminate boards, MDF and particle board- ♫ = no-noise with a special sound absorbing resin inside the silent slots- HW grade: KCR05 (K01-C4)
Pin holes: PH01= 2/10/60PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60PH04= 2/14/110 + 2/7/110 + 4/9/100 + 4/19/120 + 2/9/130 (Selco-Gabbani-SCM)PH05= 4/15/105 + 3/7/100 (Giben-Homag-MacMazza)
12.29
2019 - Sawblades
H H
H
H H H H H H
H H H H H H H H
HW PANEL SIZING SAWBLADESART. HCS
Item D d B/c Z Pin holesHCS300.06030 ♫ 300 30 4,4/3,2 60 PH02 HCS300.06065 ♫ 300 65 4,4/3,2 60 Selco HCS300.06075 ♫ 300 75 4,4/3,2 60 Homag HCS300.06080 ♫ 300 80 4,4/3,2 60 Gabbiani HCS300.07230 ♫ 300 30 4,4/3,2 72 PH02 HCS300.07265 ♫ 300 65 4,4/3,2 72 Selco HCS300.07280 ♫ 300 80 4,4/3,2 72 Gabbiani
HCS320.06050 ♫ 320 50 4,4/3,2 60 Giben HCS320.06065 ♫ 320 65 4,4/3,2 60 Selco HCS320.07250 ♫ 320 50 4,4/3,2 72 Giben HCS320.07275 ♫ 320 75 4,4/3,2 72 Giben
HCS321.06065 ♫ 320 65 4,6/3,2 60 Selco
HCS330.06050 ♫ 330 50 4,4/3,2 60 Giben
HCS350.05630 ♫ 350 30 4,4/3,2 54 PH02 HCS350.05675 ♫ 350 75 4,4/3,2 54 PH05 HCS350.05680 ♫ 350 80 4,4/3,2 54 PH04 HCS350.07230 ♫ 350 30 4,4/3,2 72 PH02 HCS350.07250 ♫ 350 50 4,4/3,2 72 Giben HCS350.07260 ♫ 350 60 4,4/3,2 72 Holzma HCS350.07265 ♫ 350 65 4,4/3,2 72 Selco HCS350.07275 ♫ 350 75 4,4/3,2 72 PH05 HCS350.07280 ♫ 350 80 4,4/3,2 72 PH04
HCS351.07280 ♫ 350 80 4,6/3,2 72 PH04
HCS355.07230 ♫ 355 30 4,4/3,2 72 PH02 HCS355.07275 ♫ 355 75 4,4/3,2 72 PH05 HCS355.07280 ♫ 355 80 4,4/3,2 72 PH04
HCS360.07250 ♫ 360 50 4,4/3,2 72 Giben
HCS361.07265 ♫ 360 65 4,6/3,2 72 Selco
HCS370.07230 ♫ 370 30 4,4/3,2 72 Schelling
HCS380.07250 ♫ 380 50 4,4/3,2 72 Giben HCS380.07260 ♫ 380 60 4,4/3,2 72 Holzma HCS380.07275 ♫ 380 75 4,4/3,2 72 PH05 HCS380.07280 ♫ 380 80 4,4/3,2 72 PH04
HCS381.07260 ♫ 380 60 4,8/3,5 72 Holzma HCS381.08460 ♫ 380 60 4,8/3,5 84 Holzma
- FZ/TR triple chip teeth- For cutting double sided veneer and laminate boards, MDF, particle boardand plastic materials
- ♫ = no-noise with a special sound absorbing resin inside the silent slots- HW grade: KCR05 (K01-C4)
Pin holes: PH01= 2/10/60 - PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60PH04= 2/14/110 + 2/7/110 + 4/9/100 + 4/19/120 + 2/9/130 (Selco-Gabbani-SCM)PH05= 4/15/105 + 3/7/100 (Giben-Homag-MacMazza)
Item D d B/c Z Pin holesHCS400.06030 ♫ 400 30 4,4/3,2 60 PH01 HCS400.06075 ♫ 400 75 4,4/3,2 60 Giben-Homag HCS400.06080 ♫ 400 80 4,4/3,2 60 PH04 HCS400.07230 ♫ 400 30 4,4/3,2 72 PH01 HCS400.07260 ♫ 400 60 4,4/3,2 72 Anthon HCS400.07275 ♫ 400 75 4,4/3,2 72 Giben-Homag HCS400.07280 ♫ 400 80 4,4/3,2 72 PH04
HCS401.07280 ♫ 400 80 4,6/3,2 72 PH04
HCS402.07260 ♫ 400 60 4,8/3,5 72 Holzma
HCS420.07280 ♫ 420 80 4,4/3,2 72 PH04
HCS421.07260 ♫ 420 60 4,8/3,5 72 Holzma
HCS430.07230 ♫ 430 30 4,4/3,2 72 PH01HCS430.07260 ♫ 430 60 4,4/3,2 72 AnthonHCS430.07275 ♫ 430 75 4,4/3,2 72 GibenHCS430.07280 ♫ 430 80 4,4/3,2 72 PH04HCS430.09675 ♫ 430 75 4,4/3,2 96 Giben
HCS431.07280 ♫ 430 80 4,6/3,2 72 PH04
HCS450.07230 ♫ 450 30 4,4/3,2 72 SchellingHCS450.07260 ♫ 450 60 4,4/3,2 72 Anthon-HolzmaHCS450.07275 ♫ 450 75 4,4/3,2 72 MacMazzaHCS450.07280 ♫ 450 80 4,4/3,2 72 PH04
HCS451.07280 ♫ 450 80 4,6/3,2 72 PH04
HCS452.07260 ♫ 450 60 4,8/3,5 72 Holzma-NanxingHCS452.07280 ♫ 450 80 4,8/3,5 72 PH04
HCS460.07230 ♫ 460 30 4,4/3,2 72 Schelling
HCS470.07275 ♫ 470 75 4,4/3,2 72 GibenHCS470.09675 ♫ 470 75 4,4/3,2 96 Giben
HCS480.07230 ♫ 480 30 4,4/3,2 72 Schelling
HCS481.07260 ♫ 480 60 4,8/3,5 72 HolzmaHCS481.07280 ♫ 480 80 4,8/3,5 72 Selco
HCS482.07280 ♫ 480 80 5,2/3,5 72 Selco
HCS500.06060 ♫ 500 60 4,8/3,5 60 HolzmaHCS500.07230 ♫ 500 30 4,6/3,2 72 SchellingHCS500.07260 ♫ 500 60 4,8/3,5 72 Holzma
HCS520.06060 ♫ 520 60 4,8/3,5 60 HolzmaHCS520.07230 ♫ 520 30 4,8/3,5 72 Schelling
HCS530.06030 ♫ 530 30 5,0/3,5 60 SchellingHCS531.06060 ♫ 530 60 5,8/4,0 60 Anthon
HCS540.08460 ♫ 540 60 4,8/3,5 84 Holzma
HCS541.06060 ♫ 540 60 5,8/4,0 60 Holzma
HCS550.06040 ♫ 550 40 5,2/3,5 60 SchellingHCS550.07299 ♫ 550 100 5,2/3,5 72 Giben
HCS565.07299 ♫ 565 100 5,2/3,5 72 Giben
HCS570.06060 ♫ 570 60 4,8/3,5 60 Holzma
HCS571.09660 ♫ 570 60 5,8/4,0 96 Holzma
HCS600.06060 ♫ 600 60 5,8/4,0 60 HolzmaHCS600.07260 ♫ 600 60 5,8/4,0 72 Holzma
12.30
2019 - Sawblades
HW SCORING SAWBLADES FOR EDGE BANDING AND SQUARING MACHINESART. FP
Item D d B/c Z FP100.02020R 100 20 3,2/2,2 20 FP100.02020L 100 20 3,2/2,2 20
FP115.02430R 115 30 Stefani 2,6/1,8 24 FP115.02430L 115 30 Stefani 2,6/1,8 24
FP120.03020R 120 20 3,2/2,2 30 FP120.03020L 120 20 3,2/2,2 30
FP125.03020R 125 20 3,2/2,2 30 FP125.03020L 125 20 3,2/2,2 30
FP150.03620R 150 20 3,2/2,2 36 FP150.03620L 150 20 3,2/2,2 36
FP150.03630R 150 30 3,2/2,2 36 FP150.03630L 150 30 3,2/2,2 36FP150.03655R 150 55 3,2/2,2 36 FP150.03655L 150 55 3,2/2,2 36
FP150.04820R 150 20 3,2/2,2 48 FP150.04820L 150 20 3,2/2,2 48FP150.04830R 150 30 3,2/2,2 48 FP150.04830L 150 30 3,2/2,2 48FP150.04855R 150 55 3,2/2,2 48 FP150.04855L 150 55 3,2/2,2 48
FP180.03630R 180 30 3,2/2,2 36 FP180.03630L 180 30 3,2/2,2 36
FP180.03655R 180 55 3,2/2,2 36FP180.03655L 180 55 3,2/2,2 36
FP180.03660R 180 60 3,2/2,2 36FP180.03660L 180 60 3,2/2,2 36
FP200.04830R 200 30 3,2/2,2 48FP200.04830L 200 30 3,2/2,2 48
FP200.04840R 200 40 3,2/2,2 48FP200.04840L 200 40 3,2/2,2 48
FP200.04880R 200 80 3,2/2,2 48FP200.04880L 200 80 3,2/2,2 48
- ES 1 sided top bevel teeth- R= right hand - L= left hand- For cutting double sided veneer and laminate boards, thermoplastic boards, MDF and chipboard
- HW grade: KCR06 (K01-C4)
HW SCORING SAWBLADES FOR EDGE BANDING AND SQUARING MACHINESART. FM
Item D d B/c ZFM100.02020 100 20 3,2/2,2 20
FM115.02430 115 30 2,6/1,8 24
FM120.03020 120 20 3,2/2,2 30
FM125.02020 125 20 3,2/2,2 20
FM160.04830 160 30 3,2/2,2 48
- WZ alternate top bevel teeth- For cutting double sided veneer and laminate boards, MDF and particle board- HW grade: KCR06 (K01-C4)
HW SCORING SAWBLADES FOR EDGEBANDINGAND SQUARING MACHINES (for Art. FP)
RIGHT hand (type “R”)LEFT hand (type “L”)
Sense of rotation
12.31
2019 - Sawblades
F
F
F
F
LIST OF MACHINES (SAWBLADES FOR BUILDING)
Diameter Brand Model-no.250 x 30 De Walt DW250, DW252, DW320, 1251, 1501, 1503
DW710, DW125, DW150, DW720, DW742Elu TGS 171, TGS 172, 170, 171, 172, 173,
TKS171Haffner TGS 162, Sp 198, GS 166, AKS, GS 150
Sp 195, Sp189, Sp 197, TGS198, GS12W, 2D
Metabo TK 1685 Magnum, TK 1685D, TK 1685,TK 1688, TK 1688D, TKU 1633, TKU 1693
Ulmia 1610, 1622, 1625, 1711Scheppach TKS 250Elektra-Beckum PK 3100 WM 250, PK 4200 DN 4200
PK 6000 DN 250, KS 250, KGS 250, GKS 300Festo AD85-1, AE85Flottjet 1011, 2011, 3011Mafell MKS85, MS85, Erika 85Stayer SLL250, SCE250, CP66
300 x 30 De Walt DW 1370, 142 DS, 160 DS, 1635,4L/1875/2155 3, 3L
Haffner Sp223, TGS 168, GS 157, GS 158, TGS 169, Sp 224
Ulmia 1711, 1712, 1725Metabo TK 1685 MagnumSchleicher 330, 310Holz-Her PKS 1212, -1211, -1215, -1220,
PKS 275 -1210, -1213315 x 30 Haffner KS 120
Hanning HTK 315, 3 VSMafell Biberex, BiberMatabo TK 1685 MagnumScheppach TKH, TKU, TKElektra-Beckum Combi HS 315Lutz KKS 400, JUMBO 2000, RBK 500Alko Holzmeister S, Holzmeister HAtika ATK 315 HLescha TKS 315 N, TKS 315 H, TKS 315 HS
350 x 30 De Walt C14Ulmia 1711, 1712, 1725
400 x 30 De Walt C 14, 163546+62, 2155-4+6Haffner KS 155/DGS 184, DGS 184 EMafell VKS 130, VKS 160, AZB,
TD3, TDH4, TK 150, BK3Holz-Her B7K, 277Avola ZB 400, ABH 400Atika ABK 400, ABH 400Lutz LBK 500Elektra BS 3100 WNB/400, BS 4200 DNB/400
BS 6000 DNB/500450 x 30 Mafell BKV4, TDH5, TDH 450, BK
Avola ZBV 450, ZB 450Atika ABH 450, BWK 450, ATUElektra-Beckum BS 3100 WNB/400,
BS4200 DNB/400, BS600 DNB/500Lutz RKS 700Alko W 450/W500Scheppach BS 500, BSH 500, WS 500
HW SAWBLADES FOR BUILDING SITESART. GA
Item D d B/c Z Pin holesGA300.02030 300 30 3,2/2,2 20 +anti-kickback PH01 GA315.02030 315 30 3,2/2,2 20 +anti-kickback PH01 GA350.02430 350 30 3,2/2,2 24 +anti-kickback PH01
- FZ/FA flat, beveled teeth with anti-kickback design- For cutting slab woods and boards, timber with parts of concrete and metal (nails, metal fittings), porous concrete blocks
- For table saws- HW grade: HC10 (K10-C3)
Pin holes: PH01= 2/10/60
visit our websitewww.sistemiklein.com
12.32
2019 - Sawblades
HW SAWBLADES FOR ALUMINIUMART. LA
- FZ/TR triple chip teeth- 5° positive hook angle- For Alu, PVC and non-ferrous metals. For cutting aluminium profiles and extrusions with thickness of 2-5mm
- For table saws- ♫ = no-noise with a special sound absorbing resin inside the silent slots- HW grade: HC10 (K10-C3)
* Thin kerf saw blades.Suitable for working on machine without casing.
HW SAWBLADES FOR ALUMINIUMART. LB
Item D d B/c Z Pin holesLB200.06430 ♫ 200 30 3,2/2,5 64 2/11/63 LB200.06432 ♫ 200 32 3,2/2,5 64 2/11/63
LB250.06030 ♫ 250 30 3,4/2,6 60 2/11/63LB250.08030 ♫ 250 30 3,4/2,6 80 2/11/63LB250.08032 ♫ 250 32 3,4/2,6 80 2/11/63
LB300.07230 ♫ 300 30 3,4/2,6 72 2/11/63LB300.08430 ♫ 300 30 3,4/2,6 84 2/11/63LB300.08432 ♫ 300 32 3,4/2,6 84 2/11/63LB300.09630 ♫ 300 30 3,4/2,6 96 2/11/63LB300.09632 ♫ 300 32 3,4/2,6 96 2/11/63
LB350.08430 ♫ 350 30 3,4/2,6 84 2/11/63LB350.08432 ♫ 350 32 3,4/2,6 84 2/11/63 LB350.09630 ♫ 350 30 3,4/2,6 96 2/11/63LB350.09632 ♫ 350 32 3,4/2,6 96 2/11/63 LB350.10830 ♫ 350 30 3,4/2,6 108 2/11/63LB350.10832 ♫ 350 32 3,4/2,6 108 2/11/63
LB400.09630 ♫ 400 30 4,0/3,2 96 2/11/63LB400.09632 ♫ 400 32 4,0/3,2 96 2/11/63 LB400.12030 ♫ 400 30 4,0/3,2 120 2/11/63LB400.12032 ♫ 400 32 4,0/3,2 120 2/11/63
LB450.09630 ♫ 450 30 4,0/3,2 96 2/11/63LB450.09632 ♫ 450 32 4,0/3,2 96 2/11/63 LB450.10830 ♫ 450 30 4,0/3,2 108 2/11/63LB450.10832 ♫ 450 32 4,0/3,2 108 2/11/63
LB500.12030 ♫ 500 30 4,6/3,6 120 2/11/63LB500.12032 ♫ 500 32 4,6/3,6 120 2/11/63
LB550.14030 ♫ 550 30 4,6/3,6 140 2/11/63
LB600.14030 ♫ 600 30 4,6/3,6 140 2/11/63
- FZ/TR triple chip teeth- 5° negative hook angle- For Alu, PVC and non-ferrous metals- For table saws- ♫ = no-noise with a special sound absorbing resin inside the silent slots- HW grade: HC10 (K10-C3)
RPM suggested referred to the blade diameter
Other sizes are available on request
Item D d B/c Z Pin holesLA200.06430 ♫ 200 30 3,2/2,5 64 2/11/63 LA200.06432 ♫ 200 32 3,2/2,5 64 2/11/63
LA250.06030 ♫ 250 30 3,4/2,6 60 2/11/63LA250.06032 ♫ 250 32 3,4/2,6 60 2/11/63LA250.08030 ♫ 250 30 3,4/2,6 80 2/11/63LA250.08032 ♫ 250 32 3,4/2,6 80 2/11/63
LA300.07230 ♫ 300 30 3,4/2,6 72 2/11/63LA300.07232 ♫ 300 32 3,4/2,6 72 2/11/63LA300.08430 ♫ 300 30 3,4/2,6 84 2/11/63LA300.08432 ♫ 300 32 3,4/2,6 84 2/11/63LA300.09630 ♫ 300 30 3,4/2,6 96 2/11/63LA300.09632 ♫ 300 32 3,4/2,6 96 2/11/63
LA350.08430 ♫ 350 30 3,4/2,6 84 2/11/63LA350.08432 ♫ 350 32 3,4/2,6 84 2/11/63 LA350.09630 ♫ 350 30 3,4/2,6 96 2/11/63LA350.09632 ♫ 350 32 3,4/2,6 96 2/11/63 LA350.10830 ♫ 350 30 3,4/2,6 108 2/11/63LA350.10832 ♫ 350 32 3,4/2,6 108 2/11/63
LA400.09630 ♫ 400 30 4,0/3,2 96 2/11/63LA400.09632 ♫ 400 32 4,0/3,2 96 2/11/63 LA400.09732 ♫ * NEW 400 32 3,6/3,0 96 2/11/63LA400.12030 ♫ 400 30 4,0/3,2 120 2/11/63LA400.12032 ♫ 400 32 4,0/3,2 120 2/11/63
LA420.09630 ♫ NEW 420 30 4,0/3,2 96 2/11/63 LA420.09632 ♫ 420 32 4,0/3,2 96 2/11/63
LA450.09630 ♫ 450 30 4,0/3,2 96 2/11/63LA450.09632 ♫ 450 32 4,0/3,2 96 2/11/63 LA450.09732 ♫ * NEW 450 32 3,8/3,2 96 2/11/63LA450.10830 ♫ 450 30 4,0/3,2 108 2/11/63LA450.10832 ♫ 450 32 4,0/3,2 108 2/11/63
LA500.12030 ♫ 500 30 4,6/3,6 120 2/11/63LA500.12032 ♫ 500 32 4,6/3,6 120 2/11/63
LA500.12130 ♫ NEW 500 30 4,0/3,2 120 2/11/63LA500.12132 ♫ * 500 32 4,0/3,2 120 2/11/63
LA550.14030 ♫ 550 30 4,6/3,6 140 2/11/63LA550.14130 ♫ 550 30 4,2/3,6 140 2/11/63LA600.14030 ♫ 600 30 4,6/3,6 140 2/11/63
12.33
2019 - Sawblades
L
L
L
L
L
L
L
L
L
L
L
HW GROOVING SAWBLADESART. KA
Item D d B/c ZKA125.0123015 125 30 1,5/1,1 12KA125.0123018 125 30 1,8/1,3 12 KA125.0123020 125 30 2,0/1,4 12 KA125.0123025 125 30 2,5/1,6 12KA125.0123030 125 30 3,0/2,0 12KA125.0123035 125 30 3,5/2,5 12KA125.0123040 125 30 4,0/2,8 12KA125.0123045 125 30 4,5/3,2 12KA125.0123050 125 30 5,0/4,0 12 KA125.0123060 125 30 6,0/4,0 12KA125.0123070 125 30 7,0/6,0 12 KA125.0123080 125 30 8,0/6,0 12 KA125.0123090 125 30 9,0/6,0 12 KA125.0123099 125 30 10,0/6,0 12
KA150.0183015 150 30 1,5/1,1 18KA150.0183018 150 30 1,8/1,3 18 KA150.0183020 150 30 2,0/1,4 18 KA150.0183025 150 30 2,5/1,6 18KA150.0183030 150 30 3,0/2,0 18KA150.0183035 150 30 3,5/2,5 18KA150.0183040 150 30 4,0/2,8 18KA150.0183050 150 30 5,0/4,0 18 KA150.0183060 150 30 6,0/4,0 18KA150.0183070 150 30 7,0/6,0 18 KA150.0183080 150 30 8,0/6,0 18 KA150.0183090 150 30 9,0/6,0 18 KA150.0183099 150 30 10,0/6,0 18
KA180.0243020 180 30 2,0/1,4 24 KA180.0243025 180 30 2,5/1,6 24KA180.0243030 180 30 3,0/2,0 24KA180.0243035 180 30 3,5/2,5 24KA180.0243040 180 30 4,0/2,8 24KA180.0243050 180 30 5,0/4,0 24 KA180.0243060 180 30 6,0/4,0 24KA180.0243070 180 30 7,0/6,0 24 KA180.0243080 180 30 8,0/6,0 24 KA180.0243090 180 30 9,0/6,0 24 KA180.0243099 180 30 10,0/6,0 24
- FZ flat teeth- For cutting along and across grain of hardwood, softwood, timber wood, and plastic coated panel
- For producing grooves- HW grade: KCR06 (K01-C4)
HW SAWBLADES FOR PVCART. LE
Item D d B/c Z Pin holesLE200.06430 ♫ NEW 200 30 3,0/2,5 64LE250.08030 ♫ NEW 250 30 3,0/2,5 80 PH01LE300.09630 ♫ NEW 300 30 3,0/2,5 96 PH01LE350.10830 ♫ NEW 350 30 3,2/2,5 108 PH01LE400.12030 ♫ NEW 400 30 3,6/3,0 120 2/11/63LE450.12030 ♫ NEW 450 30 3,8/3,2 120 2/11/63LE500.12030 ♫ NEW 500 30 4,0/3,2 120 2/11/63LE550.14030 ♫ NEW 550 30 4,2/3,5 140 2/11/63LE600.14030 ♫ NEW 600 30 4,2/3,5 140 2/11/63
- WZ/FA alternate-trap, teeth - Suitable for cutting PVC- ♫ = no-noise with a special sound absorbing resin inside the silent slots- For table saws- HW grade: KCR05 (K01-C4)
Pin holes: PH01= 2/10/60
12.34
2019 - Sawblades
HW SAWBLADES FOR “SOLID SURFACE”ART. MES
Item D d B/c Z Pin holesMES250.06030♫ 250 30 3,2/2,5 60 PH02MES250.08030♫ 250 30 3,2/2,5 80 PH02MES300.08430♫ 300 30 3,2/2,5 84 PH02MES300.09630♫ 300 30 3,2/2,5 96 PH02MES350.11230♫ 350 30 3,2/2,5 112 PH02
- FZ/TR triple chip teeth- 3° negative hook angle- Ideal for cutting solid surface “Corian ®” “Varicor” ecc- Suitable for plexiglass and plastic materials- High finishing grade, no scratch, no risk of material melting- ♫ = No-noise- HW grade: KCR05 (K01-C4)
Pin holes: PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60
HW SAWBLADES FOR PVC AND PLEXIGLASSART. MGS
Item D d B/c Z Pin holesMGS250.08030♫ 250 30 2,6/2,0 80 PH02 MGS300.08430♫ 300 30 2,6/2,0 84 PH02MGS300.09630♫ 300 30 2,6/2,0 96 PH02
- WZ/FA alternate-trap, teeth - 3° negative hook angle- Suitable for thin plastic, plexiglass, PVC and plywood- ♫ = No-noise- HW grade: KCR06 (K01-C4)
Pin holes: PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60
RPM suggested referred to the blade diameter
HW “DRY” OR “QUATTRO” SAWBLADESART. LZ
Item D d B/c Z Pin holesLZ150.03020 150 20 2,2/1,6 30 LZ160.03020 160 20 2,2/1,6 30 LZ180.03430 180 30 2,2/1,6 30 LZ190.03830 190 30 2,2/1,6 38
LZ200.04030 200 30 2,2/1,6 40 LZ210.04030 210 30 2,2/1,6 40 LZ230.04430 230 30 2,2/1,6 40 2/7/42
LZ250.04820 250 20 2,4/1,8 48 2/7/42 LZ250.04830 250 30 2,4/1,8 48 2/7/42
LZ300.06026 300 25,4 2,4/1,8 60 2/7/42+2/10/60LZ300.06030 300 30 2,4/1,8 60 2/7/42+2/10/60
LZ305.08026 305 25,4 2,4/1,8 80 2/7/42+2/10/60LZ350.08030 350 30 2,6/2,0 70 2/7/42+2/10/60LZ355.08026 355 25,4 2,6/2,0 80 2/7/42+2/10/60
LZ400.08430 400 30 3,0/2,0 84 2/10/60
- TR special form of teeth- 3° negative hook angle- For cutting wood, ferrous and no-ferrous material, plastic and compound materials
- For hand saws, mitre-saws and table saws- HW grade: SMX (P20 - P25 - C6)
RPM suggested referred to the blade diameter
M
HW SAWBLADES FOR “SANDWICH” PANELSART. MP
Item D d B/c Z Pin holesMP250.08030 250 30 2,8/2,2 80MP300.09630 300 30 2,8/2,2 96 PH01MP350.10830 350 30 3,2/2,6 108 PH01MP400.10830 400 30 3,4/2,8 108 PH01MP450.12030 450 30 3,6/3,0 120MP500.12040 500 40 3,8/3,2 120MP550.14040 550 40 4,2/3,6 140MP600.14440 600 40 4,2/3,6 144
- FZ/TR triple chip teeth- HW grade: SMX (P20 - P25 - C6)
Pin holes: PH01= 2/10/60
HW SAWBLADES FOR FRAMESART. MLS - MMS
α
Item D d B/c a Z Pin holesMLS250.08030♫ 250 30 3,0/2,5 10° 80 PH02MLS300.09630♫ 300 30 3,0/2,5 10° 96 PH02
MMS300.09630♫ 300 30 3,0/2,5 5° 96 PH02
- WZ alternate top bevel teeth- Excellent finish on 45° cut- ♫ = No-noise- MLS excellent for MDF and PVC frame- MMS for difficult cutting - HW grade: KCR06 (K01-C4)
Pin holes: PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60
40°40°
α
ART. MLS
ART. MMS
12.35
2019 - Sawblades
HW DMo5 SAWBLADES FOR FERROUS MATERIALSART. PA - PB
Item D d B Form Z Pin holesPA225.12032 225 32 2,0 C 120 2/8/45+2/11/63+2/9/50PA225.12040 225 40 2,0 C 120 2/8/55+4/12/64
PB225.18032 225 32 2,0 BW 180 2/8/45+2/11/63+2/9/50PB225.18040 225 40 2,0 BW 180 2/8/55+4/12/64
PA250.12832 250 32 2,0 C 128 2/8/45+2/11/63+2/9/50PA250.12840 250 40 2,0 C 128 2/8/55+4/12/64
PB250.20032 250 32 2,0 BW 200 2/8/45+2/11/63+2/9/50PB250.20040 250 40 2,0 BW 200 2/8/55+4/12/64
PA275.14032 275 32 2,5 C 140 2/8/45+2/11/63+2/9/50PA275.14040 275 40 2,5 C 140 2/8/55+4/12/64
PB275.22032 275 32 2,5 BW 220 2/8/45+2/11/63+2/9/50PB275.22040 275 40 2,5 BW 220 2/8/55+4/12/64
PA300.16032 300 32 2,5 C 160 2/8/45+2/11/63+2/9/50PA300.16040 300 40 2,5 C 160 2/8/55+4/12/64
PB300.22032 300 32 2,5 BW 220 2/8/45+2/11/63+2/9/50PB300.22040 300 40 2,5 BW 220 2/8/55+4/12/64
PA315.16032 315 32 2,5 C 160 2/8/45+2/11/63+2/9/50PA315.16040 315 40 2,5 C 160 2/8/55+4/12/64
PB315.22032 315 32 2,5 BW 220 2/8/45+2/11/63+2/9/50PB315.22040 315 40 2,5 BW 220 2/8/55+4/12/64
PA325.16040 325 40 2,5 C 160 2/8/55+4/12/64
PA350.18032 350 32 2,5 C 180 2/8/45+2/11/63+2/9/50PA350.18040 350 40 2,5 C 180 2/8/55+4/12/64
PB350.28032 350 32 2,5 BW 280 2/8/45+2/11/63+2/9/50PB350.28040 350 40 2,5 BW 280 2/8/55+4/12/64
PA370.19040 370 40 3,0 C 190 2/8/55+4/12/64
PA400.16040 400 40 3,0 C 160 2/8/55+4/12/64
- Vaporized execution for steel, pipe, ferrous materials - Fit for low RPM table saws- Art. PA = form “C”- Art. PB = form “BW”
Form “BW” Form “C”
12.36
2019 - Sawblades
DP CONICAL SCORING SAWBLADESART. XFI
H
Item D d B/c Z Pin holesXFI120.02020 120 20 3,1-3,7/2,2 20XFI120.02022 120 22 3,1-3,7/2,2 20
XFI125.02420 125 20 3,1-3,7/2,2 20XFI125.02422 125 22 3,1-3,7/2,2 20
XFI160.03645 160 45 4,4-5,0/3,2 36 GibenXFI160.03655 160 55 4,4-5,0/3,2 36 Gabbiani
XFI180.03620 180 20 4,4-5,0/3,2 36XFI180.03645 180 45 4,4-5,0/3,2 36 HolzmaXFI180.04450 180 50 4,4-5,0/3,2 44 Giben
XFI181.03645 180 45 4,8-5,6/3,5 36 Holzma
XFI182.03620 180 20 5,8-6,6/4,0 36 Anthon
XFI200.03620 200 20 4,4-5,0/3,2 36XFI200.03630 200 30 4,4-5,0/3,2 36XFI200.03645 200 45 4,4-5,0/3,2 36 HolzmaXFI200.03665 200 65 4,4-5,0/3,2 36 Selco
XFI201.03645 200 45 4,8-5,6/3,5 36 HolzmaXFI201.03665 200 65 4,8-5,6/3,5 36 Selco
XFI202.03620 200 20 5,0-5,8/3,5 36 Schelling
XFI203.03645 200 45 5,8-6,6/4,0 36 Holzma
XFI215.04250 215 50 4,4-5,0/3,2 42 Giben
- (KON/FZ) DP conical teeth- For cutting along and across grain of softwoods, hardwood and exotic timber, double-side veneer laminate boards, MDF and plywood
- Tooth height H= 4 mm
DP SAWBLADESART. XFC
Item D d B/c Z Pin holesXFC250.04830 250 30 3,2/2,2 48 PH02XFC250.06030 250 30 3,2/2,2 60 PH02
XFC300.06030 300 30 3,2/2,2 60 PH02XFC300.07230 300 30 3,2/2,2 72 PH02
XFC350.07230 350 30 3,5/2,5 72 PH02XFC350.08430 350 30 3,5/2,5 84 PH02XFC350.09630 350 30 3,5/2,5 96 PH02
- (FZ/TR) DP triple chip teeth- For cutting along and across grain of softwoods, hardwood and exotic timber, double-side veneer laminate boards, MDF and plywood
- Tooth height H= 4 mm
Pin holes: PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60
DP ADJUSTABLE SCORING SAWBLADESART. XFL
Item D d B/c Z XFL125.01020 125 20 2,8-3,4/2,2 10+10XFL125.01022 125 22 2,8-3,4/2,2 10+10
- (LFZ) DP flat teeth- Supplied with spacers- For cutting along and across grain of softwoods, hardwood and exotic timber, double-side veneer laminate boards, MDF and plywood
- For panel sizing machines- Tooth height H= 4 mmCONTACT US
(+39) 0721 [email protected]
X
DP PANEL SIZING SAWBLADESART. XHC
0,5
16°
Item D d B/c Z Pin holesXHC300.06030 300 30 4,4/3,2 60 PH02XHC300.06065 300 65 4,4/3,2 60 Selco
XHC320.06050 320 50 4,4/3,2 60 GibenXHC320.06065 320 65 4,4/3,2 60 Selco
XHC330.06050 330 50 4,4/3,2 60 Giben
XHC350.07230 350 30 4,4/3,2 72 PH02XHC350.07250 350 50 4,4/3,2 72 GibenXHC350.07260 350 60 4,4/3,2 72 HolzmaXHC350.07265 350 65 4,4/3,2 72 SelcoXHC350.07275 350 75 4,4/3,2 72 PH05XHC350.07280 350 80 4,4/3,2 72 PH04
XHC360.07250 360 50 4,4/3,2 72 GibenXHC360.07265 360 65 4,4/3,2 72 Selco
XHC370.07230 370 30 4,4/3,2 72 PH02
XHC380.07260 380 60 4,8/3,5 72 Holzma
XHC400.07230 400 30 4,4/3,2 72 2/10/60XHC400.07260 400 60 4,4/3,2 72 AnthonXHC400.07275 400 75 4,4/3,2 72 Giben-HomagXHC400.07280 400 80 4,4/3,2 72 PH04
XHC401.07260 400 60 4,8/3,5 72 Holzma
XHC420.07260 420 60 4,8/3,5 72 Holzma
XHC430.07275 430 75 4,8/3,5 72 GibenXHC430.07280 430 80 4,8/3,5 72 PH04
XHC450.07230 450 30 4,4/3,2 72 SchellingXHC450.07280 450 80 4,4/3,2 72 PH04
XHC451.07260 450 60 4,8/3,5 72 HolzmaXHC451.07280 450 80 4,8/3,5 72 PH04
XHC460.07230 460 30 4,4/3,2 72 Schelling
XHC470.07275 470 75 4,4/3,2 72 Giben
XHC480.07230 480 30 4,4/3,2 72 Schelling
XHC481.07260 480 60 4,8/3,5 72 HolzmaXHC481.07280 480 80 4,8/3,5 72 Selco
XHC500.07260 500 60 4,8/3,5 72 Holzma
XHC520.07260 520 60 4,8/3,5 60 Holzma
- (FZ/TR) DP triple chip teeth- For cutting along and across grain of softwoods, hardwood and exotic timber, double-side veneer laminate boards, MDF and plywood
- Tooth height H= 4 mm (can be produced also with H= 5/6 mm)
Pin holes: PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60PH04= 2/14/110 + 2/7/110 + 4/9/100 + 4/19/120 + 2/9/130 (Selco-Gabbiani-SCM)PH05= 4/15/105 + 3/7/100 (Giben-Homag-MacMazza)
12.37
2019 - Sawblades
Item D d B/c Z Pin holesXGE160.10420 ♫ NEW 160 20 2,4/1,6 4 2/6/32 XGE160.10820 ♫ NEW 160 20 2,4/1,6 8 2/6/32
XGE190.10420 ♫ NEW 190 20 2,4/1,6 4 2/6/32
XGE200.10430 ♫ NEW 200 30 2,4/1,6 4 2/7/42 XGE200.10830 ♫ NEW 200 30 2,4/1,6 8 2/7/42 XGE216.10830 ♫ NEW 216 30 2,4/1,6 8 - XGE230.10630 ♫ NEW 230 30 2,4/1,6 6 2/7/42 XGE250.10630 ♫ NEW 250 30 2,4/1,6 6 PH02 XGE250.11230 ♫ NEW 250 30 2,4/1,6 12 PH02
XGE300.11230 ♫ NEW 300 30 2,4/1,6 12 PH02 XGE300.12030 ♫ NEW 300 30 2,4/1,6 20 PH02
DP SAWBLADES FOR CUTTING ABRASIVEMATERIALSART. XGE
- Suitable for cutting cement fiber, plasterboards, fiber reinforced plastics, solid surface and Eternit- DP flat teeth- DP tooth height 3,5 mm- ♫ = No-noise
Pin holes: PH02= 2/7/42 + 2/9,5/46,5 + 2/10/60
D d
B
c
12.38
2019 - Sawblades
SAFETY PIN HOLES FOR SAWBLADESART. FT
Item pcs.LAME.FT.x1 1LAME.FT.x2 2LAME.FT.x3 3
Specify number of pin holes, sawblade diameter and pitch circle diameteres
SPECIAL SAWBLADE REBORING ART. AF
d
Item pcs.LAME.AF.x1 1LAME.AF.x2 2LAME.AF.x3 3
- Specify diameter (d)- Reboring is never recommended- Maximum reboring of the blade is 20 mm of the original bore size
REDUCTION RINGS FOR SAWBLADESART. ZA
Item D d ZA000.02012 20 12,7 ZA000.02013 selling out 20 13 ZA000.02015 selling out 20 15 ZA000.02016 20 16
ZA000.03015 selling out 30 15 ZA000.03016 30 16 ZA000.03020 30 20 ZA000.03025 30 25 ZA000.03026 30 25,4 ZA000.03028 selling out 30 28,6
ZA000.03220 32 20 ZA000.03230 32 30
ZA000.03516 35 16 ZA000.03520 35 20 ZA000.03526 35 26 ZA000.03530 35 30ZA000.03532 35 32
ZA000.04030 40 30ZA000.04032 40 32ZA000.04035 40 35