2014+ H-D FLH MODELS - Motorcycle · PDF fileThis setting must be changed by a Harley Davidson...
Transcript of 2014+ H-D FLH MODELS - Motorcycle · PDF fileThis setting must be changed by a Harley Davidson...
125 Industrial Drive | Spearfish, SD 57783 | Toll Free 888.3WHEELS w w w . l e h m a n t r i k e s . c o m
2014+ H-D FLH MODELS
Limited Lean Suspension Installation Instructions
January 2015
*All 2014+ Models require changes to the BAS settings in the Body Control Module
2
• Safety Information • Specifications • Disassembly • Swingarm • Differential and Suspension Installation • Belt Alignment • Top Mount and Rocker Adjustment • Seat Mount • Sway Bar Installation • Brake System • Exhaust • Lights and Wiring • Body Installation • Side Cover Installation • Trunk Door Installation • Final Assembly • Steering Neck Preload
© 2010. All rights reserved. Lehman Trikes® provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Lehman Trikes® assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Lehman Trikes® reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Lehman Trikes® is a registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America.
SECTION BREAKOUT
3
UNDERSTANDING SAFETY LABELS & INSTRUCTIONS
READ AND BECOME FAMILIAR WITH ALL WARNING, CAUTION SYMBOLS AND STATEMENTS
LISTED BELOW AND IN THE TEXT OF THIS MANUAL BEFORE YOU BEGIN WORK.
DANGER, WARNINGS & CAUTION SYMBOLS
This is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Your safety is involved!
SAFETY ALERT WARNING indicates a potential hazard that may result in severe injury or death to the operator, by-stander or person (s) inspecting or servicing the vehicle.
WARNING
Indicates a potential hazard that may result in minor per-sonal injury or damage to the vehicle.
CAUTION
CAUTION indicates special precautions that must be taken to avoid vehicle damage or property damage.
CAUTION
NOTE provides key information by clarifying instructions.
NOTE:
IMPORTANT provides key reminders during disassembly, assembly and inspection of components.
IMPORTANT:
SAFETY INFORMATION
4
General Safety Information This kit is designed to be installed by a competent technician. Improper installation can affect the safe operation of your trike, which could also result in serious injury or death. Make sure you have a complete understanding of the work to be preformed. Unqualified installers are urged to have the unit installed by a trained technician.
• Always protect yourself when the vehicle is in the air. Make sure the vehicle is properly supported anytime you use a hoist or jack.
• Always use the proper tools.
• Protect your eyes by using proper safety glasses or goggles.
• Read through the installation instructions before you begin. Make sure you have all the proper tools, parts and skill set to perform the installation safely and completely.
SAFETY INFORMATION
WARNING
5
Specifications • Verify that you have all components before assembly.
• Before installing your new Lehman kit, we recommend that your motorcycle be inspected and serviced by a qualified technician. Replace any worn or damaged parts before installing the trike kit.
• If the motorcycle has more than 12,000 miles, Lehman Trikes recommends installing a new drive belt during the trike conversion.
• CAUTION: This kit is not designed for use on lowered motorcycles. Interference be-tween the tires and body may occur.
INFORMATION
Overall Width 57.5" Overall Length 103" Wheel Base 72" Curb Weight 1204lb Rear Tire Size 205/70‐15 Rear Tire Pressure 26 PSI Rear Suspension Double A‐Arm Independent Storage 5.75 Cubic feet
6
WARNING- 2014+ Models: Before the trike installation is complete, the Bank Angle Sensor (BAS) setting must be changed in the Body Control Module (BCM) from “Internal” to “External”. This setting must be changed by a Harley Davidson dealer. Failure to repro-gram BCM to correct setting may cause engine to stall while riding. Death or serious in-jury may occur. 1. Install and route Bank Angle Sensor Assembly as shown in Fig’s. 1 & 2.
BANK ANGLE SENSOR INSTALLATION
Fig. 1
Sensor/Bracket
Route Green wire behind battery to BCM on LH side
Route Red and Black wires to front of battery
Sensor mounts below frame plate behind Battery/ECM
Fig. 2
7
2. See Fig. 3. Connect Black wire to negative (-) battery terminal. Splice Red wire to Green/Purple
wire on spare H-D plug located in front of battery.
2. See Fig. 4. Route Green wire to BCM connector located behind LH side cover. Remove BCM from
bracket and unplug main connector. Remove rear cover on connector to access terminals. 3. See Fig. 5. Locate B4 on BCM connector and install green wire. Verify that terminal locks into
place. Reinstall cover to connector and plug into BCM. Reinstall BCM and LH side cover.
NOTE: Once conversion is complete and BCM has been reprogrammed, verify that “red” security light on speedometer stays off. Any BCM fault codes may need to be cleared.
BANK ANGLE SENSOR INSTALLATION
Locate spare plug in front of battery
Splice red wire from BAS to Green/Purple wire on H-D harness
Connect Black wire from BAS to negative battery terminal
Route Green wire to backside of BCM connector
Install Green wire to B4 location in BCM connector
Fig. 3
Fig. 4 Fig. 5
8
Disassembly NOTE: Refer to the H-D service manual for de-tailed instructions on removal of OEM parts. 1. Load motorcycle on lift and secure front wheel. 2. Place motorcycle on center stand or scissor
style jack. 3. Remove seat, save mounting hardware. 4. Remove side covers. NOTE: Save tour box mounting hardware 5. Remove tour box liner and disconnect any wir-
ing. Remove tour box. (if equipped) 6. Remove saddlebags (if equipped). 7. Remove saddlebag frames (if equipped). 8. Remove tour box frame (if equipped). 9. Remove passenger footboards. 10. Remove mufflers. 11. Disconnect air lines and remove rear shocks. 12. Remove rear wheel. 13. Disconnect rear brake line at caliper and remove
caliper. 14. Remove rear fender. 15. See Fig. 1. Remove pivot shaft nut from LH side
of swingarm. Remove swingarm frame brackets. Tap pivot shaft out of swingarm and remove from RH side. Remove swingarm from motorcycle. Bearings and spacers will be reused.
16. See Fig. 2. Remove lower swingarm/frame mounting hardware from differential assembly. Remove lower adjuster bracket hardware from each side.
17. Temporarily remove swingarm and rear frame from differential assembly.
18. See Fig. 3. Temporarily remove upper seat mount frame from differential assembly.
PREPARING THE MOTORCYCLE Fig. 1
OEM Swingarm
Fig. 2
Remove swingarm/frame hardware
Remove lower hardware
Fig. 3
Remove upper frame
9
Swingarm NOTE: Trim LH & RH head pipes before installing swingarm. 1. Trim 2-1/4”” from RH head pipe. Trim 1-1/2” from
LH head pipe. Additional trimming may be re-quired during exhaust installation.
2. See Fig. 1. Modify original outer spacers by drill-ing to 3/4” I.D. Verify that spacers slide freely over full length of swingarm pivot shaft.
3. See Fig’s 2 & 3. Install original swingarm bear-ings into trike swingarm opposite from OEM ori-entation.
4. See Fig’s 2 & 3.Install modified spacer opposite from OEM orientation.
5. Apply Anti-Seize to OEM pivot shaft. 6. Position trike swingarm over transmission hous-
ing. Slide pivot shaft through swingarm and transmission housing.
7. Install rubber mounts, cup washer and nut to pivot shaft. Use blue Loctite on pivot shaft nut.
8. Install LH and RH swingarm frame brackets. Use blue Loctite on mounting bolts. Align rubber mount index tab with bracket slots.
9. Torque pivot shaft bolt to 45 ft-lbs. 10. Torque swingarm frame bracket bolts to 42 ft-lbs. 11. Verify swingarm has no side to side movement.
Loosen and re-torque pivot shaft if necessary.
INSTALLATION Fig. 1
Fig. 2
Fig. 3
Before After
3/4”
Bearing Modified spacer
10
Differential/Suspension Assembly WARNING: Differential assembly is ex-
tremely heavy. Verify assembly is properly sup-ported and secure while installing to motorcy-cle. Additional help may be required during in-stallation. 1. Set differential assembly on lift behind swin-
garm. 2. See Fig. 1. Remove the upper and lower rear
(3) connector tubes on differential assembly. 3. See Fig. 2. Pass the left side of differential as-
sembly through the drive belt. Place drive belt onto pulley.
4. See Fig. 2. Reinstall (3) connector tubes. Ap-ply 1-2 drops of oil to bolts. Torque hardware to 150 ft-lbs.
5. See Fig 3. Install Top seat mount frame and spacers to motorcycle frame using the follow-ing hardware. Torque 5/16” bolts to 20 ft-lbs. • (6) 5/16” x 1-3/4” Hex Head Bolts– CB2022 • (12) 5/16” Flat Washers– CW2013 • (6) 5/16” Lock Nuts– CN3045
INSTALLATION Fig. 1
Fig. 2
Fig. 3
Place belt on pulley
Tubes removed
11
Differential/Suspension Assembly 7. See Fig. 4. Raise differential assembly and
attach to top seat mount frame using removed hardware. Temporarily tighten bolts. • (4) 1/2” x 1-1/2” Hex Bolts • (8) 1/2” Flat Washers • (4) 1/2” Lock Nuts
8. See Fig. 5. Attach swingarm and rear body frame to differential assembly using removed hardware. Leave hardware loose for belt ad-justment. • (4) 1/2” x 3-1/2” Hex Bolts– CB2017 • (8) 1/2” Flat Washers– CW2178 • (4) 1/2” Lock Nuts– CN3060
NOTE: See Fig. 5. Use rear holes in swingarm for all models. 9. See Fig. 6. Install belt adjuster brackets to
swingarm from top body mount frame using the following hardware. Mount to rear holes on swingarm. • (2) 3/8” x 1-1/4” Hex Bolts– CB2018 • (4) 3/8” Flat Washers– CW2180 • (2) 3/8” Lock Nuts– CN3051
10. Torque belt adjuster bracket hardware to 30 ft-lbs.
INSTALLATION Fig. 4
Fig. 5
Fig. 6
Use rear holes on swingarm
Body frame
Swingarm
12
Belt Alignment and Tensioning 1. See Fig. 1. Adjust belt tension and differential
alignment by moving differential assembly for-ward or rearward as needed using adjuster bolts.
NOTE: Verify adjuster bolts are equal from side to side before tightening hardware. 2. Set belt tension by measuring total vertical
movement. • New Belt- 3/4”-1” • Used Belt- 1”-1-1/2”
3. Check belt alignment by turning the pulley by hand, verifying that belt runs in the center of the pulley. Belt may ride next to flange as long as it’s not trying to climb.
4. Recheck belt alignment after making any ad-justments.
5. After all adjustments are made, tighten adjuster jam nuts
6. See Fig. 2. Torque front swingarm/frame mounting bolts to 50 ft-lbs.
7. Check belt alignment and adjust as needed. 8. See Fig. 2. Once belt alignment is correct,
torque rear swingarm/frame bolts to 50 ft-lbs. NOTE: See Fig. 3. Rear shocks are preset on the fourth setting (4 complete revolutions on lower collar) from the factory. Shocks have a total of 7 settings. Adjust shocks as needed.
INSTALLATION Fig. 1
Fig. 2
Front Rear
Adjuster bolt
Fig. 3
Soft Firm
13
Top Mount and Rocker Adjustment
INSTALLATION Fig. 1
1. See Fig. 1. Verify vibration rockers are close to vertical (within a few degrees of vertical is accept-able) before tightening upper hardware.
2. If rockers are vertical, torque upper hardware to 50 ft-lbs. 3. If rockers are not vertical, loosen belt adjuster bracket and adjust as needed. Torque adjuster
bracket hardware to 30 ft-lbs when finished.
Vibration rockers
14
Seat Mount 1. See Fig. 1. Install the seat mounting bracket to
the upper trike frame using the following hard-ware. Torque hardware to 30 ft-lbs. • (1) 09+ Seat Mount Bracket– S002118
• (4) 3/8” x 1-1/4” Hex Head Bolts– CB2018
• (16) 3/8” Flat Washers– CW2180
• (8) 3/8” Lock Nuts– CN3050 2. Reuse stud plate from OEM fender. 3. See Fig. 2. Cut off end (harness guide) from
plate. 4. See Fig. 3. Install stud plate to seat mount us-
ing OEM retainers. 5. Install chrome grab handle to seat mounting
using OEM hardware.
• (1) Grab Handle– LH1026
INSTALLATION Fig. 1
Fig. 2
Fig. 3
15
Sway Bar Installation 1. See Fig’s 1 & 2. Install sway bar to rear trike
frame behind differential using the following hardware. Torque to 30 ft-lbs. • (4) 3/8” x 1” Hex Bolt- CB2000 • (8) 3/8” Flat Washers- CW2180
• (4) 3/8” Lock Nuts- CN3051 2. See Fig. 3. Install sway bar rod ends to upper
LH and RH control arms using the following hardware. Install one washer to each side of rod end. • (2) 3/8” x 2-1/4” Hex Bolt- CB2001
• (6) 25/64” Stainless Flat Washers-CW2182
• (2) 3/8” Lock Nut- CN3051 3. Adjust rod end on LH side in or out until bolt
moves freely. 4. Tighten jam nuts on rod ends.
• Tighten rod end hardware. Torque to 30ft-lbs
INSTALLATION Fig. 1
Fig. 2
Fig. 3
Install washers
RH Side Shown
16
Brake System CAUTION: Brakes are a critical safety compo-nent of the trike. Verify all brake components have been properly installed before test riding. Improper brake operation could result in death or serious injury. Do not allow dirt or debris to enter master cylinder reservoir. New brake pads and rotors will have a break-in period be-fore optimum brake operation is achieved. 1. See Fig. 1. Connect residual valve to brass
block as shown using a copper banjo washer. Torque valve to 11 ft-lbs. • (1) Residual Valve– S002037
• (1) Copper Banjo Washer- GC6002 2. See Fig. 1. Connect OEM brake line to residual
valve using the following hardware. Torque banjo bolt to 16 ft-lbs. • (1) M10 x 20 Banjo Bolt-S002229
• (2) Copper Banjo Washer- GC6002 3. Remove reservoir cap. 4. Bleed rear brake system at rear calipers with
brake bleeder or hand operated vacuum pump. 5. Repeat bleeding until all air is eliminated from
brake system. Verify rear brake pedal is firm and does not bottom out.
6. Fill fluid reservoirs and install caps. 7. ABS MODELS See Fig. 2. Place ABS dis-
abled label over light on tachometer.
INSTALLATION Fig. 1
Valve
Fig. 2
Place “ABS Disabled” sticker over light
17
Exhaust 1. Verify head pipes were properly trimmed during
disassembly. NOTE: Additional trimming may be required to head pipes and exhaust extensions. Aftermar-ket exhaust may require additional modifica-tions. 2. Install exhaust extensions and clamps to head
pipes. • (1) RH Exhaust Extension– S002231
• (1) LH Exhaust Extension– S002230
• (2) Exhaust Clamps– GC1016 3. See Fig’s 1 & 2. Install muffler plates to frame
using the following hardware. NOTE: Tighten muffler hardware until 2-3 threads are visible through lock nuts. Do not over tighten hardware.
• (2) Muffler Plate– S002170
• (6) Muffler Vibration Mount– S002225 4. Install mufflers to extensions using the OEM
clamps. 5. See Fig. 3. Mount mufflers to brackets using
the following hardware. • (4) 5/16” x 3/4” Hex Head Bolts– CB1154
• (4) 5/16” Flat Washers- CW2013
• (4) 5/16” Lock Washers– CW2045 6. Verify alignment on all exhaust components
and tighten exhaust clamps.
INSTALLATION Fig. 1
Fig. 3
Fig. 2
LH muffler mount
18
INSTALLATION Lights and Wiring 1. Install wire harness to trike body. Route light mod-
ule and main harness connector along RH side of body. • (1) Trinity Wiring Harness– S002032
NOTE: Module will connect to battery once body is installed. 2. Route brake wiring to rear of body following wiring
clips on each side. Route connector with yellow wires to RH taillight. Route connector with gray wires to LH taillight.
3. Route trailer harness, license plate and accessory wiring along RH side and below trunk.
NOTE: Do not over tighten taillight mounting hard-ware. Damage to housing may occur. 4. See Fig 1. Mount taillight assemblies to body with
gaskets. Attach ground wire to stud with flange nut after taillight mounting hardware is installed. • (2) Taillight Assembly-S002204 • (2) Gaskets– BG0200 • (4) 1/4” Flat Washer– CW2006 • (4) Lock Washer– Provided with light • (4) Nut– Provided with light • (2) 1/4” Flange Nut– CN3007
5. See Fig’s 2 & 3. If required- Install female termi-nals and male connectors to taillight wiring Use appropriate tool for crimping terminals to wires. (Mac Tools– TCT1028).
6. See Fig’s 2 & 3. Inspect crimps before installing into connector. Distortion should be minimal.
Taillight/Body Wiring-
Attach ground wire to stud
Fig. 1
Fig. 2
Wire core crimp
Insulation crimp
Function Taillight Trike Harness Brake # 1 Red Yellow Tail # 2 Black Yellow (Center Terminal)
Ground # 3 Green Black
Female Terminal
Fig. 3
1
2
3
19
INSTALLATION Fig. 1
Fig. 2
License Plate Light 1. See Fig. 1. Install license plate light to housing
and install housing to door using the following hardware. • (1) License Plate Light– S002237 • (2) 6/32” Screw– CS4073 • (1) Chrome Housing– S002238 • (2) 1/4” x 1” Button Head Bolt– CB1086 • (2) 1/4” Flat Washer SS– CW2006
2. See Fig. 1. Install license plate bracket to door using the following hardware. Use rubber washers between bracket and door. • (3) 1/4” x 1-1/4” Button Head Bolt– CB1094 • (3) 1/4“ Rubber Washer– CW2096 • (3) 1/4” Flat Washer SS- CW2006 • (3) 1/4” Lock Nut CN3040
3. See Fig. 1. Install U-nuts to bracket. • (2) 1/4” U-nut CN3301
4. See Fig. 2. Install License plate to bracket us-ing the following hardware. • (2) 1/4” x 1/2” Button Head Bolt– CB1083
20
Body Installation NOTE: The installation /alignment of the body is an important process to find the correct posi-tion of the body in relation to the wheels. The pre-drilled holes in the body are for shipping purposes. Re-drill the holes if necessary once the body is properly aligned. 1. Carefully place trike body on frame and posi-
tion using the (6) body mounts. Install the fol-lowing hardware and leave loose.
• (6) 3/8” Fender Washers– CW2180
• (6) 3/8” Thin Lock Nuts– CN3055 2. Align body to trike. Center body by checking
side to side (wheel opening) and front to back (front of fender) measurements.
NOTE: Open mounting holes if necessary to achieve proper alignment. 3. Torque all body mounting nuts to 20 ft-lbs. 4. See Fig. 1. Route emergency release cable
from trunk along RH side of motorcycle frame. Secure emergency release with cable ties to sit behind RH side cover.
5. See Fig. 1. Plug main connector from trike body harness to rear lighting connector on mo-torcycle. Install positive and negative leads (Red +, Black- ) from harness to battery termi-nals.
6. See Fig. 2. Drill 3/8” hole in RH trunk pocket. Install grommet to body.
• (1) Grommet– GG0011 7. Route license plate and accessory wiring
through grommet. Apply silicone around har-ness and grommet.
8. Secure trailer hitch, license plate wiring to clips on body. Secure excess hitch wiring to rear frame bar with cable ties.
INSTALLATION Fig. 1
RH trunk floor
Install grommet and wiring
Secure hitch wiring
Fig. 2
Connect to main harness
Secure trunk release cable to RH frame
21
Trunk Door Installation Note: Lip on weather seal will face away from door opening; top of seal is flush with top of door. 1. See Fig. 1. Install door seal around edge of
body, starting at center on bottom and following trunk opening. Trim seal ends straight with scissors; glue ends together when finished.
• (6’) Door Seal– CW2536 2. See Fig 2. Install trunk door to body with origi-
nal hinge hardware. 3. Adjust hinges and strikers as needed to
achieve proper seal around door. 4. See Fig. 3. Install female terminals and male
connector to license plate wiring and plug into body harness. Verify light wiring matches har-ness wiring as follows. • Black wire (-) from light to Black wire on
body harness • Blue wire (+) from light to Blue wire on
body harness 5. Secure wiring to LH hinge with cable ties
needed. 6. See Fig. 3. Tuck accessory wiring inside door
opening. Black (-), Red (+).
INSTALLATION Fig. 1
Lip on weather seal
Top of seal is flush with door opening
Fig. 3
Fig. 2
License plate
Accessory
22
Tour Pack Installation 1. See Fig. 1. Cover painted surfaces with masking
tape before locating bracket and drilling body. Place tour pack mounting bracket on top of body. Locate bracket as far forward as possible. • (1) Trinity Tour Pack Bracket– S002239
2. Align tour pack bracket from side to side and front to back.
CAUTION: Verify that front mounting holes will not interfere with trunk wall. Front holes should be drilled on the outside of trunk. 4. See Fig. 1. Once tour box bracket is aligned in
desired location, mark (6) mounting holes on body.
5. Drill holes in body to 1/4”. 6. Install bracket to body using the following hard-
ware. Rubber gasket must be installed between body and bracket to prevent paint or material damage. • (2) Rubber Gasket– S002299 • (6) 1/4” x 1-1/4” Button Head– CB1094 • (6) 1/4” Flat Washers– CW2007 • (6) 1/4” Lock Nuts– CN3040
6. See Fig. 2. Place tour pack on mounting bracket. Use the slotted mounting holes on bracket for 2014+ models. Install using the following hard-ware Loctite 242. Torque nuts to 8 ft.-lbs. • (4) OEM Nuts
7. Reinstall all tour pack wiring in proper locations. 8. Reinstall tour pack liner.
INSTALLATION Fig. 1
Fig. 2
Front
Front
2014+ Mounting
23
Trunk Release Cable Mounting 1. Before installing the tour box inner liner, route
the trunk release cable from the front of the body up through the left side grommet hole in tour box.
2. See Fig. 1. Install the trunk release cable bracket to the left rear corner as shown using OEM hardware. • (1) Cable Release Bracket– S002282
3. See Fig. 2. With the knob of the cable re-moved, lay in the top box liner. Mark the loca-tion of the cable and remove the liner. Drill a 1/2” hole for the cable to pass through and re-install the liner.
4. Reinstall the cable knob. 5. Adjust trunk latch assembly as needed for
proper cable operation and door seal.
INSTALLATION Fig. 1
Fig. 2
24
Final Assembly 1. Install seat to mounting tab using original H-D
mounting hardware. Caution: Do not use an impact wrench when installing lug nuts. 2. Install wheels. Torque wire wheel lug nuts to
75 ft.-lbs. and aluminum wheel lug nuts to 85 ft.-lbs. Install center caps (if applicable).
3. Set rear tire pressure at 26 psi. 4. Install reflectors to body. See Fig. 1. Install rear
reflectors 3” below taillights on body. 5. See Fig. 2. Install side reflectors using wheel
center caps as a reference, 1/4” above wheel opening on body.
6. Install Trinity and LLS badges to bottom right side of door. Install Lehman badge to bottom left side of door. • (1) Trinity Badge– GB1329 • (1) Lehman Badge– GB1327 • (1) LLS Badge– GB1328
INSTALLATION Fig. 1
Fig. 2
25
Neck Race Preload Steering head should be approximately twice as tight as factory specifications for a trike conversion. Refer to H-D service manual for adjustment procedure. Caution: Do not tighten bolts past factory specifications. Only bearing adjustment collar should be tightened past factory settings.
INSTALLATION
Fig. 1