2008 Mondeo Owner manual
Transcript of 2008 Mondeo Owner manual
Feel the differenceFordMondeoOwner's handbook
The information contained in this publication was correct at the time of going to print. In the interest ofdevelopment the right is reserved to change specifications, design or equipment at any time withoutnotice and without incurring any obligations. This publication, or part thereof, may not be reproducednor translated without our approval. Errors and omissions excepted.
© Ford Motor Company 2009
All rights reserved.
Part number: 9S7J-19A321-DA (CG3536en) 06/2009 20090622094208
E108837
IntroductionAbout this handbook................................7Symbols glossary.......................................7Parts and accessories..............................7
Quick startQuick start.................................................10
Child safetyChild seats................................................19Booster cushions....................................20Child seat positioning.............................22ISOFIX anchor points..............................24Child safety locks....................................25
Occupant protectionPrinciple of operation..............................27Fastening the seat belts........................29Seat belt height adjustment..................29Seat belt reminder..................................30Using seat belts during pregnancy......30Disabling the passenger airbag............30
Keys and remote controlsGeneral information on radio
frequencies..........................................32Programming the remote control........32Changing the remote control
battery...................................................32
LocksLocking and unlocking...........................36Global opening and closing...................38Keyless entry...........................................40
Engine immobiliserPrinciple of operation..............................43Coded keys.............................................43Arming the engine immobiliser.............43Disarming the engine immobiliser........43
AlarmPrinciple of operation..............................44Arming the alarm.....................................46Disarming the alarm................................46
SteeringwheelAdjusting the steering wheel.................47Audio control............................................47
Wipers andwashersWindscreen wipers.................................49Autowipers...............................................49Windscreen washers.............................50Rear window wiper and washers.........50Headlamp washers.................................51Checking the wiper blades....................51Changing the wiper blades....................51
LightingLighting control........................................53Autolamps................................................54Front fog lamps.......................................54Rear fog lamps........................................54Adjusting the headlamps - Vehicles
With: Adaptive Front Lighting/XenonHeadlamps...........................................55
Headlamp levelling..................................55Hazard warning flashers........................56Adaptive front lighting system
(AFS)......................................................56Direction indicators.................................58Interior lamps...........................................58Removing a headlamp...........................59Changing a bulb......................................60Bulb specification chart..........................67
Windows andmirrorsElectric windows.....................................69Exterior mirrors.........................................71Electric exterior mirrors...........................71
1
Table of contents
Auto-dimming mirror..............................73
InstrumentsGauges.....................................................74Warning lamps and indicators...............76Audible warnings and indicators...........78
Information displaysGeneral information................................79Trip computer..........................................88Personalised settings.............................90Information messages...........................92
Climate controlPrinciple of operation.............................101Air vents...................................................101Manual climate control.........................102Automatic climate control....................104Heated windows and mirrors..............106Auxiliary heater.......................................107Electric sunroof.......................................111
SeatsSitting in the correct position................115Manual seats...........................................115Electric seats...........................................116Head restraints.......................................118Rear seats...............................................118Heated seats..........................................119Ventilated seats......................................119
Convenience featuresSun blinds................................................121Instrument lighting dimmer...................121Clock........................................................121Cigar lighter.............................................121Ashtray....................................................122Auxiliary power sockets.......................122Cup holders............................................123
Glove box...............................................123Storage compartments........................123Map pockets..........................................124Memory function...................................124Glasses holder.......................................125CD changer............................................125Auxiliary input (AUX IN) socket............125USB port.................................................126
Starting the engineGeneral information...............................127Ignition switch.........................................127Keyless starting......................................127Steering wheel lock...............................129Starting a petrol engine........................129Starting a petrol engine - E85.............130Starting a diesel engine.........................131Diesel particulate filter (DPF).................131Switching off the engine.......................132Engine heater.........................................132
Fuel and refuellingFuel quality - Petrol................................133Fuel quality - E85...................................133Fuel quality - Diesel...............................133Catalytic converter................................134Fuel filler flap...........................................134Refuelling................................................135Refuelling - E85......................................135Fuel consumption..................................135Technical specifications........................136
TransmissionManual transmission.............................138Automatic transmission........................138
BrakesPrinciple of operation.............................141Hints on driving with ABS......................141
2
Table of contents
Parking brake..........................................141
Stability controlPrinciple of operation............................142Using stability control............................142
Hill start assistPrinciple of operation............................143Using hill start assist..............................143
Active suspensionPrinciple of operation............................146Using active suspension......................146
Parking aidPrinciple of operation............................147Using the parking aid............................147
Cruise controlPrinciple of operation............................149Using cruise control..............................149
Adaptive cruise control(ACC)
Principle of operation.............................151Using ACC..............................................152Forward alert function..........................155
Load carryingGeneral information...............................157Luggage anchor points........................157Sliding loadspace floor..........................158Rear under floor storage......................160Cargo nets..............................................160Luggage covers.....................................161Roof racks and load carriers...............162Dog guard...............................................162Load retaining fixtures..........................164
TowingTowing a trailer.......................................166Detachable tow ball..............................166
Driving hintsRunning-in...............................................170General driving points - Vehicles With:
Sports Suspension.............................170Cold weather precautions...................170Driving through water...........................170
Emergency equipmentFirst aid kit................................................171Warning triangle......................................171
Status after a collisionInspecting safety system
components.......................................172
FusesFuse box locations................................173Changing a fuse.....................................175Fuse specification chart........................176
Vehicle recoveryTowing points.........................................185Towing the vehicle on four wheels.....185
MaintenanceGeneral information...............................187Opening and closing the bonnet........188Engine compartment overview - 1.6L
Duratec-16V Ti-VCT (Sigma)............189Engine compartment overview - 2.0L
Duratec-HE (MI4)...............................190Engine compartment overview - 2.3L
Duratec-HE (MI4)...............................191Engine compartment overview - 2.5L
Duratec (VI5).......................................192Engine compartment overview - 1.8L
Duratorq-TDCi (Lynx) Diesel............193
3
Table of contents
Engine compartment overview - 2.0LDuratorq-TDCi (DW) Diesel..............194
Engine compartment overview - 2.2LDuratorq-TDCi (DW) Diesel..............195
Engine oil dipstick - 1.6L Duratec-16VTi-VCT (Sigma)...................................196
Engine oil dipstick - 2.0L Duratec-HE(MI4)/2.3L Duratec-HE (MI4)...........196
Engine oil dipstick - 2.5L Duratec(VI5)......................................................196
Engine oil dipstick - 1.8L Duratorq-TDCi(Lynx) Diesel........................................196
Engine oil dipstick - 2.0L Duratorq-TDCi(DW) Diesel/2.2L Duratorq-TDCi (DW)Diesel....................................................197
Engine oil check.....................................197Engine coolant check...........................197Brake and clutch fluid check...............198Power steering fluid check..................198Washer fluid check................................199Technical specifications........................199
Vehicle careCleaning the exterior............................202Cleaning the interior.............................202Repairing minor paint damage...........203
Vehicle batteryUsing booster cables...........................204Battery connection points...................205
Wheels and tyresGeneral information..............................206Changing a road wheel.......................206Tyre repair kit..........................................210Run flat tyres..........................................216Tyre care.................................................217Using winter tyres..................................217Using snow chains................................217Tyre pressure monitoring system.......218Technical specifications........................219
Vehicle identificationVehicle identification plate...................222Vehicle identification number (VIN).....222
Technical specificationsTechnical specifications.......................223
TelephoneGeneral information..............................231Telephone setup...................................231Bluetooth setup....................................232Telephone controls..............................233Using the telephone - Vehicles Without:
Navigation System............................233Using the telephone - Vehicles With:
Navigation System............................236
Voice controlPrinciple of operation...........................238Using voice control...............................238Audio unit commands.........................239Telephone commands........................250Navigation system commands..........254Climate control commands................254
ConnectivityGeneral information..............................257Connecting an external device..........258Connecting an external device -
Vehicles With: Bluetooth..................258Using a USB device..............................259Using an iPod.........................................261
Navigation introductionRoad Safety...........................................265
Navigation systemGetting started......................................266
4
Table of contents
AppendicesType approvals......................................268Type approvals......................................268Type approvals......................................268Electromagnetic compatibility............269
5
Table of contents
6
ABOUT THISHANDBOOK
Thank you for choosing Ford. Werecommend that you take some time toget to know your vehicle by reading thishandbook. The more that you know aboutit, the greater the safety and pleasure youwill get from driving it.
WARNING
Always drive with due care andattention when using and operatingthe controls and features on your
vehicle.
Note: This handbook describes productfeatures and options available throughoutthe range, sometimes even before theyare generally available. It may describeoptions not fitted to your vehicle.
Note: Always use and operate yourvehicle in line with all applicable laws andregulations.
Note: Pass on this handbook whenselling your vehicle. It is an integral part ofthe vehicle.
SYMBOLSGLOSSARY
Symbols in this handbook
WARNING
You risk death or serious injury toyourself and others if you do notfollow the instructions highlighted
by the warning symbol.
CAUTION
You risk damaging your vehicle if youdo not follow the instructionshighlighted by the caution symbol.
Symbols on your vehicle
When you see these symbols, read andfollow the relevant instructions in thishandbook before touching or attemptingadjustment of any kind.
PARTSANDACCESSORIES
Nowyou can be sure that yourFord parts are Ford parts
Your Ford has been built to the higheststandards using high quality Ford OriginalParts. As a result, you can enjoy driving itfor many years.
Should the unexpected occur and a majorpart needs replacing, we recommend thatyou accept nothing less than Ford OriginalParts.
The use of Ford Original Parts ensuresthat your vehicle is repaired to itspre-accident condition and maintains itsmaximum residual value.
Ford Original Parts match Ford's stringentsafety requirements and high standardsof fit, finish and reliability. Quite simply, theyrepresent the best overall repair value,including parts and labour costs.
Now it is easier to tell if you have reallybeen given Ford Original Parts. The Fordlogo is clearly visible on the following partsif they are Ford Original Parts. If yourvehicle has to be repaired, look for theclearly visible Ford branding and makesure that only Ford Original Parts havebeen used.
7
Introduction
Look for the Ford logo on thefollowing parts
Sheetmetal
• Bonnet
• Doors
• Luggage compartment lid or tailgate
E88678
Bumper and radiator grille
• Radiator grille
• Front and rear bumper
E88505
Exteriormirror
E88506
Glass
• Rear window
• Side glass
• Windscreen
8
Introduction
E88507
Lighting
• Rear lamps
• Headlamp
E88508
9
Introduction
QUICKSTART
Instrument panel overview - left-hand drive
A I J K L MCB G HFED
V O NU T S R Q P
E87719
10
Quick start
Instrument panel overview - right-hand drive
E87720
D E F B ALK G CH
N VPT S R Q UO
IJ M
Lighting controls. See Lighting control (page 53).A
Air vents. See Air vents (page 101).B
Direction indicators. SeeDirectionindicators (page 58). Telephone controlbuttons. See Telephone controls (page 233). Voice control buttons. SeeUsing voice control (page 238).
C
Instrument cluster. See Gauges (page 74).D
Information display controls. See Information displays (page 79).E
Wiper lever. See Windscreenwipers (page 49).F
Start Button. See Keyless starting (page 127).G
Audio or navigation unit. See separate handbook.H
Stability control (ESP)switch. See Using stability control (page 142).I
11
Quick start
Parking aid switch. See Using the parking aid (page 147).J
Hazard warning flasher switch. SeeHazardwarning flashers (page 56).K
Passenger airbag deactivation warning lamp. SeeDisablingthepassengerairbag (page 30).
L
Heated windscreen and heated rear window switches. See Heatedwindows andmirrors (page 106).
M
Climate controls. SeeManualclimatecontrol (page 102). SeeAutomaticclimate control (page 104).
N
Cigar lighter. See Cigar lighter (page 121).O
Ignition switch. See Ignition switch (page 127).P
Cruise control switches. See Using cruise control (page 149). Adaptivecruise control switches. See Using ACC (page 152).
Q
Steering wheel adjustment lever. SeeAdjustingthesteeringwheel (page47).
R
Horn.S
Cruise control switches. See Using cruise control (page 149). Adaptivecruise control switches. See Using ACC (page 152).
T
Driver Knee airbag. See Principle of operation (page 27).U
Storage compartment. See Storage compartments (page 123).V
Keyless entry
E78276
Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.
Unlocking the vehicle
E78278
Pull a door handle to unlock all the doorsand the luggage compartment lid anddisarm the alarm.
12
Quick start
Locking the vehicle
E87384
E87435
See Keyless entry (page 40).
Adjusting the steeringwheel
WARNING
Never adjust the steering wheelwhen the vehicle is moving.
1
2
2
E95178
3E95179
See Adjusting the steeringwheel(page 47).
13
Quick start
Autowipers
B
C
D
AE70696
Single wipeA
AutowipersB
Normal wipeC
High speed wipeD
E70316
A
B
High sensitivityA
Low sensitivityB
See Autowipers (page 49).
Autolamps
E70719
The headlamps will come on and go offautomatically depending on the ambientlight.
See Lighting control (page 53).
Electric foldingmirrors
E72623
SeeElectricexteriormirrors (page71).
14
Quick start
Information displays
E70499
Use the arrow buttons to navigatethrough the menus and press OK tomake a selection.
See Informationdisplays (page 79).
Manual climate control
Heating the interior quickly
E71377
Cooling the interior quickly
E71381
Defrosting and demisting thewindscreen
E71382
See Manual climate control (page102).
Automatic climate control
E70304
See Automatic climate control(page 104).
Memory function
WARNING
Do not use the memory storefunction when the vehicle is moving.
15
Quick start
A
B
E86768
Seat adjustment controls.A
Memory pre-set buttons.B
1. Turn the ignition on.
2. Adjust the seat and exterior mirrors tothe desired position.
3. Press and hold the desired pre-setbutton B until a single chime soundsto confirm.
See Memory function (page 124).
Engineidlespeedafterstarting
The engine may idle at a higher speedthan normal immediately after startingfrom cold.
See Starting the engine (page 127).
Keyless starting
E85766
Press the start button.
See Keyless starting (page 127).
Diesel particulate filter (DPF)
WARNING
Do not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The DPF
regeneration process creates very highexhaust gas temperatures and theexhaust will radiate a considerableamount of heat during and after DPFregeneration, and after you have switchedthe engine off. This is a potential firehazard.
See Diesel particulate filter (DPF)(page 131).
Fuel filler flap
E86613
Press the flap to open it. Open the flapfully until it engages.
16
Quick start
E119080
Insert the fuel nozzle up to and includingthe first notch on the nozzle. Keep itresting on the cover of the fuel pipeopening.
WARNING
We recommend that you wait atleast 10 seconds before removingthe fuel nozzle to allow any residual
fuel to drain into the fuel tank.
E119081
Slightly raise the fuel nozzle to remove it.
See Fuel filler flap (page 134).
Manual transmission
Selecting reverse gear
E99067
On some vehicles it is necessary to raisethe collar whilst selecting reverse gear.
SeeManualtransmission (page 138).
Automatic transmission
Selector lever positions
E80836
S
ParkP
ReverseR
NeutralN
17
Quick start
DriveD
Manual shifting and sport modeS
WARNING
Apply the brakes before moving theselector lever and keep themapplied until you are ready to move
off.
SeeAutomatic transmission (page138).
18
Quick start
CHILDSEATS
E68916
WARNINGSSecure children that are less than150 centimetres tall or less than 12years of age in a suitable, approved
child restraint, in the rear seat.
Original text according to ECER94.01: Extreme Hazard! Do not usea rearward facing child restraint on
a seat protected by an air bag in front ofit!
Read and follow the manufacturer’sinstructions when you are fitting achild restraint.
Do not modify child restraints in anyway.
Do not hold a child on your lap whenthe vehicle is moving.
Do not leave unattended children inyour vehicle.
If your vehicle has been involved inan accident, have the child restraintschecked by properly trained
technicians.
Note: Mandatory use of child restraintsvaries from country to country.
Only child restraints certified toECE-R44.03 (or later) have been testedand approved for use in your vehicle. Achoice of these are available from yourDealer.
Child restraints for differentmass groups
Use the correct child restraint as follows:
Baby safety seat
E68918
Secure children that weigh less than 13kilograms in a rearward facing baby safetyseat (Group 0+) in the rear seat.
19
Child safety
Child safety seat
E68920
Secure children that weigh between 13and 18 kilograms in a child safety seat(Group 1) in the rear seat.
BOOSTERCUSHIONS
WARNINGSDo not install a booster seat or abooster cushion with only the lapstrap of the seat belt.
Do not install a booster seat or abooster cushion with a seat belt thatis slack or twisted.
Do not put the seat belt under yourchild’s arm or behind its back.
Do not use pillows, books or towelsto boost your child’s height.
Make sure that your children sit inan upright position.
Secure children that weigh morethan 15 kilogrammes but are lessthan 150 centimetres tall in a
booster seat or a booster cushion.
Booster seat
E70710
We recommend that you use a boosterseat that combines a cushion with abackrest instead of a booster cushiononly. The raised seating position will allowyou to position the shoulder strap of theadult seat belt over the centre of yourchild’s shoulder and the lap strap tightlyacross its hips.
Booster cushion
E68924
20
Child safety
Integrated booster cushion
WARNINGSDo not use the raised integratedbooster cushion together with achild safety seat.
The integrated booster cushion canbe used for children that weighbetween 22 and 36 kilogrammes
(49 and 79 pounds).
CAUTION
Remove the rear seat head restraintunless the child's head exceeds thetop of the backrest. See Head
restraints (page 118).
Unlocking
1
2
E94860
Note: Make sure that the lockingmechanism is fully engaged.
3
E94861
The raised seating position will allow youto position the shoulder strap of the adultseat belt over the centre of your child’sshoulder and the lap strap tightly acrossits hips.
Locking
Note: Make sure that there are noobstructions in the linkage area beforelocking the integrated booster cushion.
2
E94862
1
Note: Make sure that the lockingmechanism is fully engaged.
21
Child safety
E94870
3
CHILDSEATPOSITIONING
WARNINGSWhen using a child restraint with asupport leg on a second row seat,make sure the support leg rests
securely on the floor.
When using a forward facing childseat on a second row seat, alwaysremove the head restraint from that
seat.
When fitting a child seat using thevehicle seat belts make sure thebelts are not slack.
Note: When using a child restraint on afront seat, it may prove difficult to tightenthe lap section of the seat belt withoutslack remaining. If this is the case, adjustthe seatback to the fully upright positionand raise the height of the seat. SeeSeats (page 115).
Mass group categoriesSeating positions
IIIIII0+0
22 - 36 kg15 - 25 kg9 - 18 kgUp to 13kg
Up to 10kg
UF¹UF¹UF¹XXFront passenger seatwith airbag ON
U¹U¹U¹U¹U¹Front passenger seatwith airbag OFF
UUUUURear seats
X Not suitable for children in this mass group.
U Suitable for universal category child restraints approved for use in this mass group.
U¹ Suitable for universal category child restraints approved for use in this mass group.However, we recommend that you secure children in a government approved childrestraint, in the rear seat.
22
Child safety
UF¹ Suitable for universal category forward facing child restraints approved for use inthis mass group. However, we recommend that you secure children in a governmentapproved child restraint, in the rear seat.
ISOFIX child restraints
Mass group categoriesSeating positions
IIIIII0+0
22 - 36 kg15 - 25 kg9 - 18 kgUp to 13kg
Up to 10kg
XXIL, IUF**ILILRear seat ISOFIXrestraints
XXA, B, B1, C,D
C, D, EERear seat ISOFIXclasses*
X Not suitable for children in this mass group.
IUF Suitable for universal category ISOFIX child restraints approved for use in this massgroup.
ILSuitable for the following ISOFIX child restraints: Roemer Duo ISOFIX (group 1), RoemerBabysafe ISOFIX (group 0+). In addition, any semi-universal ISOFIX child restraint maybe used if indicated in the child seat manufacturers vehicle list.
* As defined by ECE-R16.
Note: ** When you are purchasing an ISOFIX restraint, make sure that you know thecorrect mass group and ISOFIX size class for the intended seating locations.
Note: ** Make sure that the top tether mechanism does not interfere with the luggagecover.
23
Child safety
ISOFIX ANCHORPOINTS
WARNING
Use an anti-rotation device whenusing the ISOFIX system. Werecommend the use of a top tether
or support leg.
Your vehicle is fitted with ISOFIX anchorpoints that accommodate universallyapproved ISOFIX child restraints.
The ISOFIX system comprises two rigidattachment arms on the child restraintthat attach to anchor points on theoutboard rear seats, where the cushionand backrest meet. Tether anchor pointsare fitted behind the outboard rear seatsfor child restraints with a top tether.
Top tether anchor points
E87146
E93616
E93514
Attaching a child seatwith toptethers
WARNING
Do not attach a tether strap toanything other than the correcttether anchor point.
Note: Where applicable, remove theluggage cover to ease installation. SeeLuggage covers (page 161).
Note:On 4-door vehicles, make sure thetether strap tightening mechanismremains accessible when the seatback isfully engaged.
24
Child safety
E87591
1. Place the child seat on the back seatcushion and fold the relevant seatbackforwards. SeeRearseats (page 118).
2. Remove the head restraint. SeeHead restraints (page 118).
WARNING
Make sure the top tether strap is notslack or twisted and is properlylocated on the anchor point.
3. Route the tether strap to the anchorpoint.
WARNING
Make sure that the seatback issecure and fully engaged in thecatch.
4. Push the seatback to the uprightposition.
E87145
5. Push the child seat back firmly toengage the ISOFIX lower anchorpoints.
6. Tighten the tether strap in line with thechild seat manufacturer's instructions.
CHILDSAFETY LOCKS
WARNING
You cannot open the doors frominside if you have put the child safetylocks on.
25
Child safety
E73697
A
B
LockA
UnlockB
26
Child safety
PRINCIPLEOFOPERATION
Airbags
WARNINGSDo not modify the front of yourvehicle in any way. This couldadversely affect deployment of the
airbags.
Original text according to ECER94.01: Extreme Hazard! Do not usea rearward facing child restraint on
a seat protected by an airbag in front ofit!
Wear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use
the seat belt properly, can it hold you in aposition that allows the airbag to achieveits optimum effect. See Sitting in thecorrect position (page 115).
Have repairs to the steering wheel,steering column, seats, airbags andseat belts carried out by a properly
trained technician.
Keep the areas in front of theairbags free from obstruction. Donot affix anything to or over the
airbag covers.
Do not poke sharp objects intoareas where airbags are fitted. Thiscould damage and adversely affect
deployment of the airbags.
Use seat covers designed for seatswith side airbags. Have these fittedby a properly trained technician.
Note: You will hear a loud bang and seea cloud of harmless powdery residue if anairbag deploys. This is normal.
Note: Only wipe airbag covers with adamp cloth.
Driverandfrontpassengerairbags
E74302
The driver and front passenger airbagswill deploy during significant frontalcollisions or collisions that are up to 30degrees from the left or the right. Theairbags will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thuscushioning forward body movement.During minor frontal collisions, overturns,rear collisions and side collisions, the driverand front passenger airbags will notdeploy.
Driver knee airbag
CAUTION
Do not attempt to open the driverknee airbag cover.
The driver knee airbag will deploy duringfrontal collisions or collisions that are upto 30 degrees from the left or the right.The airbag will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thusproviding a cushion between the driver’sknees and the steering column. Duringoverturns, rear collisions and sidecollisions, the knee airbag will not deploy.
For item location: SeeQuickstart (page10).
27
Occupant protection
Note: The knee airbag has a lowerdeployment threshold than the frontairbags. During a minor collision, it ispossible that only the knee airbagdeploys.
Side airbags
E72658
Side airbags are fitted inside the seatbackof the front seats. A label indicates thatside airbags are fitted to your vehicle.
The side airbags will deploy duringsignificant lateral collisions. The airbagswill inflate within a few thousandths of asecond and deflate on contact with theoccupants, thus providing protection forthe chest and shoulder areas. Duringminor lateral collisions, overturns, frontcollisions and rear collisions, the sideairbags will not deploy.
Curtain airbags
E75004
Curtain airbags are fitted inside the trimpanels over the front and rear sidewindows. Moulded badges in the B-pillartrim panels indicate that curtain airbagsare fitted to your vehicle.
The curtain airbags will deploy duringsignificant lateral collisions. The airbag willinflate within a few thousandths of asecond and deflate on contact with theoccupants, thus providing protection forthe head. During minor lateral collisions,front collisions, rear collisions, or overturnsthe curtain airbags will not deploy.
Seat belts
WARNINGSWear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use
the seat belt properly, can it hold you in aposition to achieve its optimum effect.See Sitting in the correct position(page 115).
Never use a seat belt for more thanone person.
Use the correct buckle for each seatbelt.
28
Occupant protection
WARNINGSDo not use a seat belt that is slackor twisted.
Do not wear thick clothing. The seatbelt must fit tightly around your bodyto achieve its optimum effect.
Position the shoulder strap of theseat belt over the centre of yourshoulder and position the lap strap
tightly across your hips.
The driver and front passenger seat beltretractors are fitted with a seat beltpretensioner. Seat belt pretensionershave a lower deployment threshold thanthe airbags. During minor collisions, it ispossible that only the seat beltpretensioners will deploy.
FASTENINGTHESEATBELTS
WARNING
Insert the tongue into the buckleuntil you hear a distinct click. Youhave not fastened the seat belt
properly if you do not hear a click.
E74124
E85817
Pull the belt out steadily. It may lock if youpull it sharply or if the vehicle is on a slope.
Press the red button on the buckle torelease the belt. Let it retract completelyand smoothly.
SEATBELTHEIGHTADJUSTMENT
E87511
Note: Lifting the slider slightly whilepressing the locking button makes iteasier to release the locking mechanism.
To raise or lower, press the locking buttonon the adjuster and move as necessary.
29
Occupant protection
SEATBELTREMINDER
WARNING
The occupant protection system willonly provide optimum protectionwhen you use the seat belt properly.
The seat belt reminder warninglamp illuminates and an audiblewarning will sound if the driver's
or front seat passenger's seat belt hasnot been fastened and the vehicleexceeds a relatively low speed. It will alsoilluminate if the driver's or front seatpassenger's seat belt is unfastened whenthe vehicle is moving. The audible warningwill go off after five minutes but the seatbelt reminder warning lamp will remain onuntil the driver's or front seat passenger'sseat belt is fastened.
Deactivating the seat beltreminder
See your dealer.
USINGSEATBELTSDURINGPREGNANCY
E68587
WARNING
Position the seat belt correctly foryour safety and that of your unbornchild. Do not use only the lap strap
or the shoulder strap.
Position the lap strap comfortably acrossyour hips and low beneath your pregnantabdomen. Position the shoulder strapbetween your breasts, above and to theside of your pregnant abdomen.
DISABLINGTHEPASSENGERAIRBAG
WARNING
Make sure that the passengerairbag is disabled when using arearward facing child restraint on the
front passenger seat.
E71313
30
Occupant protection
Fitting the passenger airbagdeactivation switch
WARNING
If you need to fit a child restraint ona seat protected by an operationalairbag in front of it, have a
passenger airbag deactivation switchfitted. Ask your dealer for furtherinformation.
Note: The key switch is located in theglove compartment with an airbagdeactivation lamp in the instrument panel.
If the airbag warning lamp illuminates orflashes when you are driving, this indicatesa malfunction. SeeWarninglampsandindicators (page 76). Remove the childrestraint and have the system checkedimmediately.
Disablingthepassengerairbag
A BE71312
DisabledA
EnabledB
Turn the switch to position A.
When you switch the ignition on, checkthat the passenger airbag deactivationwarning lamp illuminates.
Enabling thepassengerairbag
WARNING
Make sure that the passengerairbag is enabled when you arenotusing a child restraint on the front
passenger seat.
Turn the switch to position B.
31
Occupant protection
GENERALINFORMATIONONRADIO FREQUENCIES
CAUTION
The radio frequency used by yourremote control can also be used byother short distance radio
transmissions (e.g. amateur radios,medical equipment, wireless headphones,remote controls and alarm systems). Ifthe frequencies are jammed, you will notbe able to use your remote control. Youcan lock and unlock the doors with thekey.
Note: You could unlock the doors if youpress the buttons on the remote controlunintentionally.
The operating range between yourremote control and your vehicle variesdepending on the environment.
PROGRAMMINGTHEREMOTECONTROL
You can programme a maximum of eightremote controls to use with your vehicle(including any supplied with your vehicle).
Programming a new remotecontrol
1. Insert the key in the ignition.
2. Cycle the key from position0 to II andthen back to 0 four times in quicksuccession (about once a second).
3. Remove the key from the ignition andpress any button on the remotecontrol.
4. Reinsert the key and turn to positionII then 0. Remove the key and testthe remote control to confirmprogramming has been successful.
Reprogramming theunlockingfunction
Note:When you press the unlock buttoneither all the doors are unlocked or onlythe driver’s door is unlocked. Pressing theunlock button again unlocks all the doors.
Press and hold the unlock and lockbuttons on the remote key simultaneouslyfor at least four seconds with the ignitionoff. The direction indicators will flash twiceto confirm the change.
To return to the original unlocking function,repeat the process.
CHANGINGTHEREMOTECONTROLBATTERY
E107998
Make sure that you dispose ofold batteries in anenvironmentally friendly way.
Seek advice from your local authorityregarding recycling.
Remote control with a foldingkey blade
1
E74383
1. Insert a screwdriver as far as possibleinto the slot on the side of the remotecontrol, push it towards the key bladeand remove the key blade.
32
Keys and remote controls
E74384
2
2. Twist the screwdriver in the positionshown to start separating the twohalves of the remote control.
E743853
3. Twist the screwdriver in the positionshown to separate the two halves ofthe remote control.
CAUTION
Do not touch the battery contacts orthe printed circuit board with thescrewdriver.
4. Carefully prise out the battery with thescrewdriver.
5. Install a new battery (3V CR 2032) withthe + facing downwards.
6. Assemble the two halves of theremote control.
7. Install the key blade.
Remote control without afolding key blade
Type 1
E74386
1. Insert a screwdriver into the recess onthe back of the key and remove thekey blade.
2. Release the retaining clips with thescrewdriver and separate the twohalves of the remote control.
CAUTION
Do not touch the battery contacts orthe printed circuit board with thescrewdriver.
3. Carefully prise out the battery with thescrewdriver.
4. Install a new battery (3V CR 2032) withthe + facing upwards.
5. Assemble the two halves of theremote control.
6. Install the key blade.
33
Keys and remote controls
Type2
1
2
E78284
1. Slide the release slider in the directionof the arrow.
2. Remove the key blade.
E105064
3
3. Twist a flat bladed screwdriver in theposition shown to separate the twohalves of the remote control.
CAUTION
Do not touch the battery contacts orthe printed circuit board with thescrewdriver.
4. Carefully prise out the battery with thescrewdriver.
5. Install a new battery (3V CR 2032) withthe + facing downwards.
6. Assemble the two halves of theremote control.
7. Install the key blade.
Type3
1
2
1
E87964
1. Press and hold the pushbuttons onthe edges to release the cover.Carefully remove the cover.
2. Remove the key blade.
3
E105362
3. Twist a flat bladed screwdriver in theposition shown to separate the twohalves of the remote control.
34
Keys and remote controls
E119190
4
4
4. Carefully insert the screwdriver in theposition shown to open the remotecontrol.
CAUTION
Do not touch the battery contacts orthe printed circuit board with thescrewdriver.
5. Carefully prise out the battery with thescrewdriver.
6. Install a new battery (3V CR 2032) withthe + facing downwards.
7. Assemble the two halves of theremote control.
8. Install the key blade.
35
Keys and remote controls
LOCKINGANDUNLOCKING
Central locking
You can only centrally lock the doors ifthey are all closed.
Note: The driver’s door can be unlockedwith the key. This needs to be used if theremote control or keyless entry is notfunctioning.
Note: Central locking also locks andunlocks the fuel filler flap.
Double locking
WARNING
Do not activate double locking whenpersons or animals are inside thevehicle. You will not be able to
unlock the doors from the inside if youhave double locked them.
E71961
Double locking is a theft protection featurethat prevents someone from opening thedoors from the inside. You can onlydouble lock the doors if they are all closed.
Locking and unlockingconfirmation
When you unlock the doors, the directionindicators will flash once.
When you lock the doors, the directionindicators will flash twice.
Note: If your vehicle has double locking,the direction indicators will only flash twiceonce you have activated double locking.
Locking and unlocking thedoorswith the key
B
E71962
A
B
A
UnlockA
LockB
Double locking the doorswiththe key
Turn the key to the lock position twicewithin three seconds to double lock thedoors.
36
Locks
Locking and unlocking thedoors and the luggagecompartment lidwith theremote control
E87379
A B C
UnlockA
LockB
Luggage compartment lidunlock
C
Lockingthedoorsandthe luggagecompartment lidwith the remotecontrol
Press button B once.
Double locking the doors and theluggage compartment lidwith theremote control
Press button B twice within threeseconds.
Locking and unlocking thedoors from inside
Driver's door
A
B
E71958
Lock all doorsA
Unlock all doorsB
Front and rear passenger doors
E98653
To lock the front and rear passengerdoors individually, press the button andclose the door when leaving the vehicle.
37
Locks
Luggage compartment lid
Openingtheluggagecompartmentlidwith the remote control
Press button C on the remote controltwice within three seconds.
Closing the luggage compartmentlid
4-door
E89131
5-door
E89132
Estate
E89133
A recessed grip is incorporated inside theluggage compartment lid to facilitateclosing.
Automatic relocking
The doors will relock automatically if youdo not open a door within 45 seconds ofunlocking the doors with the remotecontrol. The door locks and the alarm willreturn to their previous state.
Reprogramming theunlockingfunction
The unlocking function may bereprogrammed so that only the driver’sdoor is unlocked. See Programmingthe remote control (page 32).
GLOBALOPENINGANDCLOSING
You can also operate the electricwindows with the ignition off via the globalopening and global closing function.
Note: Global closing will only operate ifyou have set the memory correctly foreach window. See Electricwindows(page 69).
38
Locks
Global opening
E71955
To open all the windows, press and holdthe unlock button for at least threeseconds. Press either the lock or theunlockbutton again to stop the openingfunction.
Global closing
Vehicleswithout keyless entry
WARNING
Take care when using globalclosing. In an emergency, press abutton immediately to stop.
E71956
To close all the windows, press and holdthe lock button for at least threeseconds. Press any button again to stopthe closing function. The anti-trap functionis also active during global closing.
Vehicleswith keyless entry
E87384
WARNING
Take care when using globalclosing. In an emergency, press thebutton on the driver’s door handle
to stop.
Note: Global closing can be activatedusing the button on the driver’s doorhandle. Global opening and closing canalso be activated using the buttons on thepassive key.
To close all the windows, press and holdthe button on the driver’s door handle forat least two seconds. The anti-trapfunction is also active during globalclosing.
39
Locks
KEYLESSENTRY
General information
WARNING
The keyless entry system may notfunction if the key is close to metalobjects or electronic devices such
as mobile phones.
Note: If the door handles are pulledrepeatedly during a short period of timewithout the presence of a valid passivekey, the system will become inoperablefor 30 seconds.
The passive entry system will not functionif:• The passive key frequencies are
jammed.• The passive key battery is flat.
Note: If the passive entry system doesnot function, you will need to use the keyblade to lock and unlock your vehicle.
The keyless system allows the driver tooperate the vehicle without the use of akey or remote control.
E78276
Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.These are located approximately one anda half metres from the driver and frontpassenger door handles and the luggagecompartment lid.
Passive key
The vehicle can be locked and unlockedwith the passive key. The passive key canalso be used as a remote control. SeeLocking and unlocking (page 36).
Locking the vehicle
E87384
E87435
40
Locks
WARNING
The vehicle does not lock itselfautomatically. If no locking button ispressed, the vehicle will remain
unlocked.
Note: If locking from the luggagecompartment lid, the passive key mustbe within the luggage compartment liddetection range.
Locking buttons are located on each ofthe front doors and the luggagecompartment lid.
To activate central locking and arm thealarm:• Press a locking button once.
To activate double locking, to arm thealarm and the interior sensors:• Press a locking button twice within
three seconds.
Note: Once activated, the vehicle willremain locked for approximately threeseconds. This is to allow you to pull a doorhandle and check if the vehicle is locked.When the delay period is over, the doorscan be opened again, provided thepassive key is within the respectivedetection range.
Luggage compartment lid
Note: The luggage compartment lidcannot be closed and will pop back up ifthe passive key is located inside theluggage compartment.
Note: If a second valid passive key islocated within the luggage compartmentlid detection range, the luggagecompartment lid can be closed.
Unlocking the vehicle
Note: If the vehicle remains locked forlonger than five days, the system will enteran energy-saving mode. This is to reducethe discharge of the vehicle battery. Whenthe vehicle is unlocked while in this mode,the reaction time of the system may be alittle longer than normal. Unlocking thevehicle once will deactivate theenergy-saving mode.
E78278
Pull one of the door handles or theluggage compartment lid handle.
Note: A valid passive key must belocated within the detection range of thatdoor.
One long flash of the direction indicatorsconfirms that all the doors, the luggagecompartment lid and the fuel filler flaphave been unlocked and that the alarmhas been disarmed.
Unlocking only the driver's door
If the unlocking function is reprogrammedso that only the driver’s door is unlocked( See Keys and remote controls(page 32). ), note the following:
41
Locks
If the driver’s door is the first door whichis opened, the other doors and theluggage compartment lid will remainlocked. All the other doors can beunlocked from inside the vehicle bypressing the unlock button next to thedriver’s door handle. Doors can beunlocked individually by pulling the interiordoor handles on those doors.
If the front passenger door or one of therear doors is the first door which isopened, all the doors and the luggagecompartment lid will be unlocked.
Disabled keys
Any keys left inside the vehicle interiorwhen it is locked will be disabled.
A disabled key cannot be used to turn theignition on or start the engine.
In order to use these passive keys again,they have to be enabled.
To enable all your passive keys, unlockthe vehicle using a passive key or theremote control unlocking function.
All passive keys will then be enabled if theignition is turned on or the vehicle isstarted using a valid key.
Locking and unlocking thedoorswith the key blade
Type 1
1
2
E78284
1. Slide the release slider in the directionof the arrow and pull out the key bladewith your thumb.
2. Remove the key blade and insert itinto the lock.
Type2
1
2
1
E87964
1. Carefully remove the cover.
2. Remove the key blade and insert itinto the lock.
42
Locks
PRINCIPLEOFOPERATION
The engine immobiliser is a theftprotection system that prevents someonefrom starting the engine with anincorrectly coded key.
CODEDKEYS
Note:Do not shield your keys with metalobjects. This may prevent the receiverfrom recognising your key as a valid one.
Note: Have all of your remaining keyserased and recoded if you lose a key. Askyour dealer for further information. Havereplacement keys recoded together withyour existing keys.
If you lose a key, you can obtain areplacement from your Ford Dealer. Ifpossible, provide them with the keynumber from the tag provided with theoriginal keys. You can also obtainadditional keys from your Ford Dealer.
ARMINGTHEENGINEIMMOBILISER
The engine immobiliser is armedautomatically a short time after you haveswitched the ignition off.
DISARMINGTHEENGINEIMMOBILISER
The engine immobiliser is disarmedautomatically when you switch the ignitionon with a correctly coded key.
If the message Immobiliser activeappears in the information display, yourkey has not been recognised. Removethe key and try again.
If you are unable to start the engine witha correctly coded key, this indicates amalfunction. The message Immobiliseractive will appear in the informationdisplay when you switch on the ignition.Have the immobiliser checkedimmediately.
43
Engine immobiliser
PRINCIPLEOFOPERATION
Alarmsystem
Your vehicle may be equipped with oneof the following alarm systems:
• Perimeter alarm.
• Perimeter alarm with interior sensors.
• Category one alarm with interiorsensors and battery back-up sounder.
• Category one alarm with interiorsensors, battery back-up sounder andtilt sensors.
Perimeter alarm
The perimeter alarm is a deterrent againstunauthorised access to your vehiclethrough the doors and the bonnet. It alsoprotects the audio unit.
Interior sensors
E71401
WARNING
The sensors in the interior lamp unitmust not be covered up. Do notactivate the alarm with full guard if
any persons, animals or other movingobjects are inside the vehicle.
The sensors act as a deterrent againstunauthorised intrusion by sensing anymovement within the vehicle.
Battery back-up sounder
The battery back-up sounder is an extraalarm system which will sound a sirenwhen the alarm is triggered. It is armeddirectly when you lock the vehicle. Thesounder has its own battery and willsound an alarm siren even if someonedisconnects the vehicle battery or thebattery back-up sounder itself.
Tilt sensors
The tilt sensors detect if someoneattempts to steal a wheel or tow thevehicle away by sensing changes in theinclination of the vehicle.
Note:When travelling on a ferry with thealarm armed, deactivate the tilt sensorsby selecting reduced guard. This willprevent the alarm from being triggeredby the movement.
Triggering the alarm
Once armed, the alarm is triggered in anyof the following ways:
• If someone opens a door, the tailgateor the bonnet without a valid key orremote control.
• If someone removes the audio ornavigation system.
• If the ignition is turned to position I, IIor III without a valid key.
• If the interior sensors detectmovement within the vehicle.
• On vehicles with a battery back-upsounder, if someone disconnects thevehicle battery or the battery back-upsounder itself.
• If the tilt sensors detect a change inthe inclination of the vehicle.
If the alarm is triggered, the alarm horn willsound for 30 seconds and the hazardwarning flasher will flash for five minutes.
44
Alarm
Any further attempts to perform one ofthe above will trigger the alarm again.
Full and reduced guard
Full guard
Full guard is the standard setting.
In full guard, the interior and tilt sensorsare activated when you arm the alarm.
Note: This may result in false alarms ifanimals or moving objects are inside thevehicle or, on vehicles with tilt sensors,when travelling on a ferry.
Reduced guard
In reduced guard, the interior and tiltsensors are deactivated when you armthe alarm.
Note: You can set the alarm to reducedguard for the current ignition cycle only.The next time you switch on the ignition,the alarm will be reset to full guard.
Ask on Exit
You can set the information display to askyou each time which level of guard youwish to set.
If you select Ask on Exit, the messageReduced guard? appears in theinstrument cluster display each time youswitch the ignition off.
If you wish to arm the alarm with reducedguard, press the OK button when thismessage appears.
If you wish to arm the alarm with full guard,leave the vehicle without pressing theOKbutton.
Selecting full or reduced guard
Note: SelectingReduced does not setthe alarm permanently to reduced guard.It sets it to reduced guard only for thecurrent ignition cycle. If you regularly setthe alarm to reduced guard, select Askon Exit.
E70499
E74509
Full Guard
Alarm
ReducedAsk on Exit
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. Highlight Alarm and press the rightarrow button.
45
Alarm
4. Highlight Reduced or Full guard. Ifyou prefer to be asked each time youswitch off the ignition, select Ask onExit.
5. Press the OK button to confirm theselection.
6. Press the left arrow button to exit themenu. To return to the trip computerdisplay directly, hold the left arrowbutton pressed.
Informationmessages
See Informationmessages (page 92).
ARMINGTHEALARM
To arm the alarm, lock the vehicle. SeeLocks (page 36).
DISARMINGTHEALARM
Vehicleswithout keyless entry
Perimeter alarm
Disarm and silence the alarm by unlockingthe doors with the key and switching theignition on with a correctly coded key, orunlocking the doors or the luggagecompartment lid with the remote control.
Category one alarm
Disarm and silence the alarm by unlockingthe doors with the key and switching theignition on with a correctly coded keywithin 12 seconds, or unlocking the doorsor the luggage compartment lid with theremote control.
Vehicleswith keyless entry
Note: A valid passive key must belocated within the detection range of thatdoor for keyless entry. See Keylessentry (page 40).
Perimeter alarm
Disarm and silence the alarm by unlockingthe doors and switching the ignition on,or unlocking the doors or the luggagecompartment lid with the remote control.
Category one alarm
Disarm and silence the alarm by unlockingthe doors and switching the ignition onwithin 12 seconds, or unlocking the doorsor the luggage compartment lid with theremote control.
46
Alarm
ADJUSTINGTHESTEERINGWHEEL
WARNING
Never adjust the steering wheelwhen the vehicle is moving.
Note: Make sure that you are sitting inthe correct position. See Sitting in thecorrect position (page 115).
1
2
2
E95178
3E95179
WARNING
Make sure that you fully engage thelocking lever when returning it to itsoriginal position.
AUDIOCONTROL
E72288
A
C
BD
E
Volume upA
Seek upB
Volume downC
Seek downD
ModeE
Mode
Press and hold the mode button toselect the audio source.
Press the mode button to:• tune the radio to the next preset
station• play the next CD
• play the other side of a cassette tape
• accept an incoming telephone call.
• end a telephone call.
47
Steeringwheel
Seek
Press a seek button to:• tune the radio to the next station up
or down the frequency band• play the next or the previous CD track
• fast forward or rewind the cassettetape.
Press and hold a seek button to:• tune the radio up or down the
frequency band• seek through a CD track.
48
Steeringwheel
WINDSCREENWIPERS
B
C
D
AE70696
Single wipeA
Intermittent wipeB
Normal wipeC
High speed wipeD
Intermittentwipe
E70315
BA
C
Short wipe intervalA
Intermittent wipeB
Long wipe intervalC
AUTOWIPERS
CAUTIONSDo not switch autowipers on in dryweather conditions. The rain sensoris very sensitive and the wipers may
operate if dirt, mist or flies hit thewindscreen.
Replace the wiper blades as soon asthey begin to leave bands of waterand smears. If you do not replace
them, the rain sensor will continue todetect water on the windscreen and thewipers will operate, even though themajority of the windscreen is dry.
Fully defrost the windscreen in icyconditions before you switchautowipers on.
Switch autowipers off before youenter a car wash.
E70315
BA
C
High sensitivityA
OnB
Low sensitivityC
49
Wipers andwashers
If you switch autowipers on, the wiperswill not cycle until water is detected onthe windscreen. The rain sensor will thencontinuously measure the amount ofwater on the windscreen and adjust thespeed of the wipers automatically.
Adjust the sensitivity of the rain sensorusing the rotary control. With lowsensitivity, the wipers will operate whenthe sensor detects a lot of water on thewindscreen. With high sensitivity, thewipers will operate if the sensor detectsa small amount of water on thewindscreen.
WINDSCREENWASHERS
WARNING
Do not operate the windscreenwashers for more than 10 secondsor when the reservoir is empty.
Note: The washer jets are heated whenthe ignition is on.
E70776
REARWINDOWWIPERANDWASHERS
Intermittentwipe
E70777
Reverse gearwipe
The rear window wiper will operateautomatically when you select reversegear if the wiper lever is in position B, Cor D.
Washer
WARNING
Do not operate the rear windowwasher for more than 10 secondsor when the reservoir is empty.
E70777
Pull the lever fully towards the steeringwheel and hold it to operate the washer.
50
Wipers andwashers
HEADLAMPWASHERS
The headlamp washers will operate withthe windscreen washers when theheadlamps are on.
Note: To stop the washer fluid reservoiremptying quickly, the headlamp washerswill not operate every time that you usethe windscreen washers.
CHECKINGTHEWIPERBLADES
E66644
Run the tip of your fingers over the edgeof the blade to check for roughness.
Clean the wiper blade lips with waterapplied with a soft sponge.
CHANGINGTHEWIPERBLADES
Windscreenwiper blades
CAUTIONSSet the windscreen wipers in theservice position to change the wiperblades.
CAUTIONSYou can use the service position inwinter to provide easier access tothe wiper blades for freeing them
from snow and ice. The windscreenwipers will return to their normal positionas soon as you switch on the ignition somake sure that you fully defrost thewindscreen before you switch on theignition.
Service position
E85833
A
E75188
Switch off the ignition and move the wiperlever to position A within three seconds.Release the lever when the windscreenwipers have moved to the serviceposition.
51
Wipers andwashers
Changing thewindscreenwiperblades
Set the windscreen wipers in the serviceposition and lift the wiper arms.
E728991
2
1. Press the locking button.
2. Remove the wiper blade.
Note: Make sure that the wiper bladelocks into place.
3. Install in the reverse order.
Rearwindowwiper blades
Changing the rearwindowwiperblades - Estate
1. Lift the wiper arm.
2
3
4
E86456
2. Position the wiper blade at right anglesto the wiper arm.
3. Disengage the wiper blade from thewiper arm.
4. Remove the wiper blade.
Note: Make sure that the wiper bladelocks into place.
5. Install in the reverse order.
Changing the rearwindowwiperblades - 5-door
1. Lift the wiper arm.
E864572
3
2. Press the locking button.
3. Remove the wiper blade.
Note: Make sure that the wiper bladelocks into place.
4. Install in the reverse order.
52
Wipers andwashers
LIGHTINGCONTROL
Lighting control positions
E70718
A B C
OffA
Side and tail lampsB
HeadlampsC
Parking lamps
CAUTION
Prolonged use of the parking lampswill discharge the battery.
Switch off the ignition.
Both sides
Set the lighting control to position B.
One side
E75505
A
B
Right-hand sideA
Left-hand sideB
Main and dipped beam
E70725
Pull the lever fully towards the steeringwheel to switch between main anddipped beam.
Headlamp flasher
Pull the lever slightly towards the steeringwheel.
53
Lighting
Homesafe lighting
Switch the ignition off and pull thedirection indicator lever towards thesteering wheel to switch the headlampson. You will hear a short tone. Theheadlamps will go off automatically afterthree minutes with any door open, or 30seconds after the last door has beenclosed.
With all doors closed, but within the 30second delay, opening any door will resultin the three minute timer starting again.
The home safe lights can be cancelled byeither pulling the direction indicator levertowards the steering wheel again or byturning the ignition switch on.
AUTOLAMPS
E70719
Note: If you have switched autolampson, you can only switch the main beamon when autolamps has switched theheadlamps on.
The headlamps will come on and go offautomatically depending on the ambientlight.
FRONT FOGLAMPS
E70721
WARNING
Only use the front fog lamps whenvisibility is considerably restricted byfog, snow or rain.
REARFOGLAMPS
E70720
WARNINGSOnly use the rear fog lamps whenvisibility is restricted to less than 50metres.
Do not use the rear fog lamps whenit is raining or snowing and visibilityis more than 50 metres.
54
Lighting
ADJUSTINGTHEHEADLAMPS - VEHICLESWITH: ADAPTIVE FRONTLIGHTING/XENONHEADLAMPS
To adjust the headlamps for driving on theleft or right hand side of the road, see yourdealer.
HEADLAMPLEVELLING
Note: Vehicles with Xenon headlampsare equipped with automatic headlamplevelling.
E70722
A B
Raised headlamp beamsA
Lowered headlamp beamsB
You can adjust the level of the headlampbeams according to the vehicle load.
Recommended headlamp levelling switch positions
Switch positionLoad in luggagecompartment
Load
Second rowseatsFront seats
0--1-2
0 (0.52)--1-2
1 (0.52)-31-2
55
Lighting
Switch positionLoad in luggagecompartment
Load
Second rowseatsFront seats
3 (0.52)Max131-2
4 (1.52)Max1-1
1 See Vehicle identification (page 222).2 Vehicles with active suspension.
HAZARDWARNINGFLASHERS
Note:Depending on applicable laws andregulations in the country for which yourvehicle was originally built, the hazardwarning flashers may flash if you brakeheavily.
E71943
For item location: SeeQuickstart (page10).
ADAPTIVE FRONT LIGHTINGSYSTEM (AFS)
E72897
A
B
A
B
56
Lighting
without AFSA
with AFSB
The AFS adjusts the headlamp dippedbeam depending on vehicle direction andspeed. It improves visibility when you aredriving at night and helps to reduceheadlamp glare for oncoming drivers.
The system will not operate when thevehicle is stationary, when you haveswitched on the daytime running lampsor when you have selected reverse gear.
A message will appear in the informationdisplay if the system malfunctions. SeeInformationmessages (page 92).The headlamps will move to a fixed centralor dipped position. Have the systemchecked as soon as possible.
Cornering lamps
E72898
B
A
B
A
Headlamp beamA
Cornering lamp beamB
The cornering lamps illuminate the insideof a corner when you are turning.
57
Lighting
DIRECTION INDICATORS
E70727
Note: Tap the lever up or down to makethe direction indicators flash only threetimes.
INTERIOR LAMPS
Courtesy lamp
CBA
E71945
OffA
Door contactB
OnC
If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door or the luggagecompartment lid. If you leave a door openwith the ignition switch off, the courtesylamp will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch it back on, switchon the ignition for a short time.
The courtesy lamp will also come on whenyou switch off the ignition. It will go offautomatically after a short time or whenyou start or restart the engine.
If you set the switch to positionCwith theignition switch off, the courtesy lamp willcome on. It will go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch it back on,switch on the ignition for a short time.
Reading lamps
E71946
If you switch off the ignition, the readinglamps will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch them back on,switch on the ignition for a short time.
58
Lighting
Vanitymirror lamps
A
B
E72900
OffA
OnB
If you switch off the ignition, the vanitymirror lamps will go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch them backon, switch on the ignition for a short time.
REMOVINGAHEADLAMP
WARNING
Have Xenon bulbs changed by atrained technician. There is a risk ofelectric shock.
1. Open the bonnet. SeeOpeningandclosing the bonnet (page 188).
E85995
2. Remove the screws.
E88843
3. Remove the plastic screw andretainer.
59
Lighting
5
4E85996
4. Carefully pull the corner of the grilleand bumper towards the front of thevehicle.
5. Carefully lift the corner of theheadlamp and push it as far aspossible towards the back of thevehicle.
7
6
E88982
6. Carefully pull the headlamp towardsthe centre of the vehicle, behind thegrille and bumper, to disengage it fromthe lower outer fixing point.
7. Remove the headlamp.
CAUTION
When fitting the headlamp, take carenot to damage the locating points.
Note: When fitting the headlamp, makesure that you fully engage the headlampin the lower outer fixing point.
Note:When fitting the headlamp, tightenthe front screw first and then the rearscrew.
CHANGINGABULB
WARNINGSSwitch the lights and the ignition off.
Let the bulb cool down beforeremoving it.
Have Xenon bulbs changed by atrained technician. There is a risk ofelectric shock.
CAUTIONSDo not touch the glass of the bulb.
Only fit bulbs of the correctspecification. See Bulbspecification chart (page 67).
Note: The following instructions describehow to remove the bulbs. Fitreplacements in the reverse order unlessotherwise stated.
Headlamp
Note:Remove the covers to gain accessto the bulbs.
Direction indicator
1. Remove the headlamp. SeeRemovingaheadlamp (page 59).
60
Lighting
E72259
2
3
2. Turn the bulb holder anti-clockwiseand remove it.
3. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.
Headlampmain beam
1. Remove the headlamp. SeeRemovingaheadlamp (page 59).
E72261
3
2
2. Disconnect the electrical connector.
3. Release the clip and remove the bulb.
Headlampdipped beam
1. Remove the headlamp. SeeRemovingaheadlamp (page 59).
E72260
3
2
2. Turn the bulb holder anti-clockwiseand remove it.
3. Remove the bulb.
Cornering lamp
1. Remove the headlamp. SeeRemovingaheadlamp (page 59).
E72262
3
2
2. Disconnect the electrical connector.
3. Release the clip and remove the bulb.
61
Lighting
Side repeaters
3
2
E85999
1
1. Carefully remove the side repeater.
2. Hold the bulb holder, turn the housinganti-clockwise and remove it.
3. Remove the bulb.
Approach lamp
E72264
1
Note: Position the mirror glass as farinwards as possible.
1. Insert a screwdriver into the gapbetween the mirror housing and themirror glass and release the metalretaining clip.
E72265
2
3
2. Remove the lamp.
3. Remove the bulb.
Front fog lamps
E72267
3
2
4
1
Note: You cannot separate the fog lampbulb from the bulb holder.
Note: Do not remove the screws.
1. Loosen the screws.
62
Lighting
2. Remove the lamp.
3. Disconnect the electrical connector.
4. Turn the bulb holder anti-clockwiseand remove it.
Rear lamps
Direction indicator, tail and brakelamp
E86003
1
1. Remove the trim panel.
2
E86004
2. Unclip the bulb holder.
E86005
3
A
B
Direction indicatorA
Tail and brake lampB
3. Gently press the bulb into the bulbholder, turn it anti-clockwise and removeit.
Reversing lamp, tail lamp and foglamp
1
E86006
1. Remove the trim panel.
63
Lighting
2
E86007
2. Unclip the bulb holder.
3
CB
A
E86008
Reversing lampA
Tail lampB
Fog lampC
3. Gently press the bulb into the bulbholder, turn it anti-clockwise and removeit.
Central highmounted brakelamp
Remove the trimpanel
4-door
13
E87617
1. Detach the clips.
5-door
1
2
E87618
1. Remove the screws.
2. Detach the clips.
64
Lighting
Estate
E87619
1. Detach the clips.
Remove the lamp
21 1
E87620
1. Insert a suitable object into the holes.
2. Carefully pull the lamp towards thefront of the vehicle to release thespring clips.
E86002
3
3. Remove the lamp.
3
4
E79601
4. Unclip the bulb holder.
5. Remove the bulb.
65
Lighting
Number plate lamp
E72789
3
2
1
1. Carefully release the spring clip.
2. Remove the lamp.
3. Remove the bulb.
Interior lamp
Vehicleswithout interior sensors
3
2
E72788
1. Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
Vehicleswith interior sensors
E72787
2
3
1. Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
Reading lamps
Vehicleswithout interior sensors
E72796
33
2
1. Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
66
Lighting
Vehicleswith interior sensors
E72786
22
1
1. Carefully prise out the lamp.
2. Turn the bulb holder anti-clockwiseand remove it.
E739393
3. Remove the bulb.
Vanitymirror lamp
E72785
1. Carefully prise out the lamp.
2. Remove the bulb.
Luggage compartment lamp
E72784
1. Carefully prise out the lamp.
2. Remove the bulb.
BULBSPECIFICATIONCHART
Power (watt)SpecificationLamp
21PY21WFront direction indicator
55H1Headlamp main beam
67
Lighting
Power (watt)SpecificationLamp
55H7Headlamp dipped beam
55H1Cornering lamp
5W5WSide repeater
5W5Approach lamp
351H8Front fog lamp
551H11Front fog lamp
5W5WSide lamp
21PY21WRear direction indicator
21/5P21/5WBrake and tail lamp
4P21/4WTail lamp
21/5P21/5WRear fog lamp
21P21WReversing lamp
55 x W5WCentral high mounted brake lamp
5W5WNumber plate lamp
10FestoonInterior lamp
5BA 9sReading lamp
5W5WVanity mirror lamp
5W5WLuggage compartment lamp
1Fit a replacement with the same rating as the one you have removed.
68
Lighting
ELECTRICWINDOWS
WARNING
Do not operate the electric windowsunless they are free fromobstruction.
Note: If you operate the switches oftenduring a short period of time, the systemmight become inoperable for a certaintime to prevent damage due tooverheating.
Note: You can operate the windows forseveral minutes after you switch off theignition. They will be deactivated as soonas a door is opened.
Note: If you operate both the switch onthe relevant door and the switch for thatwindow on the driver’s door at the sametime, the window will stop moving.
Switch on the ignition to operate theelectric windows.
Global opening and globalclosing
You can also operate the electricwindows with the ignition off via the globalopening and global closing function. SeeGlobal opening and closing (page38).
Note: Global opening and global closingwill open or close the windowsautomatically only on vehicles equippedwith four electric windows.
Note: Global closing will only operate ifyou have set the memory correctly foreach window.
Driver’s door switches
E70848
You can operate all the windows with theswitches on the door trim panel of thedriver’s door.
Front and rear passengers’door switches
E70849
Opening and closing thewindows automatically
Press or lift the switch to the secondaction point and release it. Press or lift itagain to stop the windows.
Safetyswitchforrearwindows
Note: You can always operate the rearwindows from the driver’s door.
69
Windows andmirrors
E70850
A switch in the driver’s door disables therear electric window switches.
The light in the switch illuminates and thelights in the rear window switches go offwhen the rear windows are disabled.
Anti-trap function
WARNING
Careless closing of the windows canoverride the protection function andcause injuries.
The electric windows will stopautomatically while closing and reversesome distance if there is an obstacle inthe way.
Overriding the anti-trap function
CAUTION
While you close the window for thethird time, the anti-trap function isdisabled. Make sure there are no
obstacles in the way of the closingwindow.
To override this protection function whenthere is a resistance, for example, in thewinter, proceed as follows:
1. Close the window twice until itreaches the resistance and let itreverse.
2. Close the window a third time to theresistance. The anti-trap function isdisabled and you cannot close thewindow automatically. The window willoverride the resistance and you canclose it fully.
3. If the window does not close after thethird attempt, have it checked by aproperly trained technician.
Resetting thememory of theelectricwindows
WARNING
The anti-trap function is deactivateduntil you have reset the memory.
After the battery has been disconnectedfrom the vehicle you must reset thememory separately for each window:
1. Lift the switch until the window is fullyclosed. Hold the switch lifted for onemore second.
2. Release the switch and lift it again, twoor three times, for one more second.
3. Open the window and try to close itautomatically.
4. Reset and repeat procedure if thewindow does not close automatically.
Safetymode
WARNING
The anti-trap function is not activeduring this procedure.
70
Windows andmirrors
If the system detects a malfunction, itenters a safety mode. The windows willmove for only about 0.5 seconds at a timeand then stop again. Close the windowsby pressing the switch again when thewindows stop moving. Have this checkedimmediately.
EXTERIORMIRRORS
WARNING
Do not overestimate the distanceof the objects that you see in theconvex mirror. Objects seen in
convex mirrors will appear smaller andfurther away than they actually are.
Manual foldingmirrors
Folding
Push the mirror towards the door windowglass.
Unfolding
Make sure that you fully engage the mirrorin its support when returning it to itsoriginal position.
ELECTRIC EXTERIORMIRRORS
A CB
E70846
Left-hand mirrorA
OffB
Right-hand mirrorC
Mirror tilting positions
E70847
The electric exterior mirrors are fitted witha heating element that will defrost ordemist the mirror glass. See Heatedwindows andmirrors (page 106).
71
Windows andmirrors
Electric foldingmirrors
Automatic folding and unfolding
Note: If the mirrors have been foldedusing the manual fold button they can onlybe unfolded using the manual fold button.
The mirrors will fold automatically whenyou lock the vehicle with the key, theremote control or a keyless entry systemrequest. The mirrors will unfold when youunlock the vehicle with the key, theremote control, a keyless entry systemrequest, the driver's interior door handleor starting the engine.
Manual folding and unfolding
The electric folding mirrors operate withthe ignition on.
Note:You can operate the mirrors (mirrortilting and folding) for several minutes afteryou switch off the ignition. They will bedeactivated as soon as a door is opened.
E72623
Press the button to fold or unfold themirrors.
If you press the switch again while themirrors are moving, they will stop andreverse the direction of movement.
Note: When the mirrors are operatedoften during a short period of time, thesystem may become inoperable for aperiod of time to prevent damage due tooverheating.
Reversemirror dipping
Depending on the switch position (A orC), the relevant exterior mirror will dipwhenever you select reverse gear, givingyou a view of the kerb.
Note: You can disable this feature byleaving the switch in position B.
The exterior mirror will return to theoriginal position:• If the vehicle speed exceeds 10 km/h
(6 mph).• Approximately 10 seconds after
reverse gear has been disengaged.• If the switch is returned to position B.
When you first use this feature, the mirrorwill dip to a preset position. This positioncan be adjusted using the followingsequence:
1. Turn the ignition on. Do not start theengine.
2. Select the desired exterior mirror (Aor C).
3. Select reverse gear, the selectedexterior mirror will adjust to a presetposition.
4. Adjust the mirror to the requireddipped position.
5. Disengage reverse gear or press andhold the desired memory pre-setbutton until a single chime sounds toconfirm. See Memory function(page 124).
The settings will be stored automatically.
72
Windows andmirrors
AUTO-DIMMINGMIRROR
E71028
The auto-dimming mirror will adjustautomatically when hit by glaring light frombehind. It will not work when you haveselected reverse gear.
73
Windows andmirrors
GAUGES
Type 1 and2
BA C D
E72984
TachometerA
Engine coolant temperature gaugeB
Fuel gaugeC
SpeedometerD
74
Instruments
Type3
A B
CDEE87713
TachometerA
SpeedometerB
Engine coolant temperature gaugeC
Fuel gaugeD
Message centre. See Information displays (page 79).E
Engine coolant temperaturegauge
Shows the temperature of the enginecoolant. At normal operating temperature,the needle will remain in the centresection.
CAUTION
Do not restart the engine until thecause of overheating has beenresolved.
If the needle moves towards 120°C, theengine is overheating. Stop the engine,switch the ignition off and determine thecause once the engine has cooleddown. See Engine coolant check(page 197).
75
Instruments
Fuel gauge
The arrow adjacent to the fuel pumpsymbol tells you on which side of yourvehicle the fuel filler cap is located.
WARNINGLAMPSANDINDICATORS
The following warning lamps andindicators will illuminate briefly when youswitch the ignition on to confirm that thesystem is operational:• ABS
• Airbag
• Brake system
• Engine
• Frost
• Ignition
• Oil pressure (all except 2.5L Duratec)
• Stability control (ESP).
If a warning or indicator lamp does notilluminate when the ignition is switchedon, it indicates a malfunction. Have thesystem checked by properly trainedtechnician.
ABSwarning lamp
If it illuminates when you aredriving, this indicates amalfunction. You will continue
to have normal braking (without ABS).Have the system checked by a properlytrained technician as soon as possible.
Airbagwarning lamp
If it illuminates while driving, thisindicates a malfunction. Havethe system checked by a
properly trained technician.
Brake system lamp
It illuminates when the parkingbrake is engaged.
WARNING
Reduce your speed gradually andstop your vehicle as soon as it issafe to do so. Use your brakes with
care.
If it illuminates when you are driving, checkthat the parking brake is not engaged. Ifthe parking brake is not engaged, thisindicates a malfunction. Have the systemchecked by a properly trained technicianimmediately.
Cruise control indicator
E71340
It will illuminate when you haveset a speed using the cruisecontrol system. See Using
cruise control (page 149). On vehicleswith adaptive cruise control (ACC), theindicator will illuminate when ACC is active.See Using ACC (page 152).
Direction indicators
Flashes during operation. Asudden increase in the rate offlashing warns of a failed
indicator bulb. See Changing a bulb(page 60).
Enginewarning lamp
If it illuminates with the enginerunning, this indicates amalfunction. If it flashes when
you are driving, reduce the speed ofyour vehicle immediately. If itcontinues to flash, avoid heavyacceleration or deceleration. Have thesystem checked by a properly trainedtechnician immediately.
76
Instruments
CAUTION
If the engine warning lamp illuminatesin conjunction with a message, havethe system checked as soon as
possible.
Forward alert indicator
It will illuminate when this featureis active. See Forward alertfunction (page 155).
Front fog lamp indicator
It will illuminate when you switchthe front fog lamps on.
Frostwarning lamp
WARNING
Even if the temperature rises toabove 4ºC (39.2°F) there is noguarantee that the road is free of
hazards caused by inclement weather.
It will illuminate and glow orangewhen the outside airtemperature is between 4ºC
(39.2ºF) and 0ºC (32ºF). It will glow redwhen the temperature is below 0ºC(32ºF).
Glowplug indicator
SeeStartingadieselengine(page 131).
Headlamp indicator
It will illuminate when you switchthe headlamp dipped beam orthe side and tail lamps on.
Ignitionwarning lamp
If it illuminates when you aredriving, this indicates amalfunction. Switch off all
unnecessary electrical equipment. Havethe system checked by a properly trainedtechnician immediately.
Low fuel level warning lamp
If it illuminates, refuel as soon aspossible.
Main beam indicator
It will illuminate when you switchthe headlamp main beam on. Itwill flash when you use the
headlamp flasher.
Message indicator
It will illuminate when a newmessage is stored in theinformation display. See
Informationmessages (page 92).
Oil pressurewarning lamp
CAUTION
Do not resume your journey if itilluminates despite the level beingcorrect. Have the system checked
by a properly trained technicianimmediately.
If it stays on after starting orilluminates when driving, thisindicates a malfunction. Stop
your vehicle as soon as it is safe to do soand switch the engine off. Check theengine oil level. See Engine oil check(page 197).
77
Instruments
Rear fog lamp indicator
It will illuminate when you switchthe rear fog lamps on.
Seat belt reminder
See Seat belt reminder(page 30).
Shift indicator
It will illuminate to inform youthat shifting to a higher gearmay give better fuel economy
and lower CO2 emissions. It will notilluminate during periods of highacceleration, braking or when the clutchpedal is pressed.
Stability control (ESP)warninglamp
While driving, it flashes duringactivation of the system. Afterswitching on the ignition, if it
does not illuminate or illuminatescontinuously while driving, this indicatesa malfunction. During a malfunction, thesystem switches off. Have the systemchecked by a properly trained technicianas soon as possible.
If you switch ESP off, the warning lampwill illuminate. The lamp will go out whenyou switch the system back on or whenyou switch the ignition off.
AUDIBLEWARNINGSANDINDICATORS
Switching the chimes on andoff
You can deactivate certain chimes.
To set which chimes should sound:
E70499
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightChimes and press the rightarrow button.
4. Highlight the chime and press theOKbutton to switch the chime on and off.
5. Press the left arrow button to exit themenu. Press and hold the left arrowbutton to return to the main menudisplay.
78
Instruments
GENERAL INFORMATION
WARNING
Do not operate the informationdisplay controls when the vehicle ismoving.
Note: The information display will remainon for several minutes after you switch offthe ignition.
Various systems on your vehicle can becontrolled using the buttons on yoursteering wheel. Correspondinginformation is displayed in the informationdisplay.
For detailed instructions on audio,navigation, phone etc. refer to theappropriate manual.
Controls
E70499
Press the up and down arrow buttons:
• to scroll through the trip computerdisplays
• to scroll through and highlight theoptions within a menu.
Press the right arrow button:
• to enter the main menu from the tripcomputer displays
• to enter a sub-menu.
Press the left arrow button to exit amenu.
Hold the left arrow button pressed at anytime to return to the main menu display(escape button).
Note: The system will return to the tripcomputer displays automatically if you donot press any button for a period of time.
Press the OK button to choose andconfirm a setting.
Instrument cluster functions
Type3Type2Type 1Function
XXXTrip computer
XXXInformation messages
XXXClock setup
XX-Display settings
XX-Park heater setup
79
Information displays
Type3Type2Type 1Function
X--Navigation control
X--CD control
X--CD changer control
X--Radio control
X--Phone control
X--Auxiliary input control
Type 1
E80604
Press the up and down arrow buttonson the steering wheel to scroll throughthe trip computer displays. See Tripcomputer (page 88).
Menu structure
Information
Reset trip TripodometerAvg. fuelAvg. speedAll values
Messages
Clock Set clock24 Hour mode12 Hour mode
E87751
80
Information displays
Type2
E74426
6.3Average Fuel
09:00
234.2 km
123456 km
l100km
Press the up and down arrow buttonson the steering wheel to scroll throughthe trip computer displays. See Tripcomputer (page 88).
81
Information displays
Menu structure
Reset Trip Trip OdoAvg. fuelAvg. speedAll
EnglishDeutschItalianoFrançaisEspañolTürkçePyccкийNederlandsPolski
PortuguêsSvenska
Configure
Language
Measure unit
Display
Set Clock24 Hour Mode12 Hour Mode
Always offOn guidanceAlways on
MessagesTyre Press.
MetricImperial
Help ScreenRadio InfoPhone InfoNAV info
Information
Clock
Setup
BA
E87752
82
Information displays
Chimes
Forw. Alert
Low Fuel
ACC warningFA warning
Home lightGeneral warn.General info.
Early
LateNormal
Sensitivity
Warn AudibleOff
ManualAuto
Hill Launch
Check
High loadLow load
Tyre Pressure
Full guard
Ask on exitReduced
Alarm
Aux. Heater
Parkheater
BA
E87753
Set Time
SaturdaySunday
FridayThursday
MondayTuesdayWednesday
Set Time
SaturdaySunday
FridayThursday
MondayTuesdayWednesday
Time 1
Time 2
OnceActive now
83
Information displays
Type3
E88048
Use the controls to scroll through themenu displays.
Device list
The highlighted icon shows the currentmenu in use.
Navigation
CD
CD changer
Radio
Phone
Trip computer
Settings
Auxiliary input
84
Information displays
Menu structure
CD
Navigation HomeDestinat. mem.Destinat. A-ZLast destinat.Cancel guidan.
DestinationsDestinationsDestinations
Folder / Tracks
Folder / TracksFolder / TracksFolder / TracksFolder / TracksFolder / TracksFolder / Tracks
StationsStationsStationsStationsStationsStationsStations
Numbers
NumbersNumbers
Station listFM 1 / FMFM 2FM 3FM - ASTMW / AMLW / AM-AST
CD changer CD 1CD 2CD 3CD 4CD 5CD 6
Radio
Phone bookRedialIncoming callsOutgoing callsCall status
Phone
AE87754
85
Information displays
Trip computer Distance to emptyAverage fuelAverage speedReset selected elementReset trip odometer
EnglishDeutschItalianoFrançaisEspañolTürkçePyccкийNederlandsPolski
PortuguêsSvenska
Colour themes
Configure
Language
Measure unit
Display
Set Clock24-hour mode12-hour mode
Always offOn guidanceAlways on
MessagesTyre Pressure
MetricImperial
Help ScreenNAV info
Settings Information
Clock
Setup
A CBE87755
A
86
Information displays
Chimes Low Fuel
ACC warningFA warning
Home lightGeneral warn.General info.
Early
LateNormal
Forw Alert Sensitivity
Warn Audible
Off
ManualAuto
Hill Launch
Check
High loadLow load
Tyre Pressure
Full guard
Ask on exitReduced
Alarm
Aux Heater
C
E87756
87
Information displays
Set Time
SaturdaySunday
WednesdayTuesday
FridayThursday
Monday
Set Time
SaturdaySunday
WednesdayTuesday
FridayThursday
Monday
Time 1
Time 2
OnceActive now
Park heater
Auxiliary input
BA
E88067
TRIPCOMPUTER
Odometer
Registers the total mileage of the vehicle.
Tripmeter
Registers the mileage of individualjourneys.
Distance to empty
Indicates the approximate distance thevehicle will travel on the fuel remaining inthe tank. Changes in driving pattern maycause the value to vary.
Average fuel consumption
Indicates the average fuel consumptionsince the function was last reset.
Average speed
Indicates the average speed calculatedsince the function was last reset.
Outside air temperature
Shows the outside air temperature.
88
Information displays
Type 1 and2
E74428
6.3Average Fuel
10:20
234.2 km
123456 km
l100km
A
B
C
A. Trip computerB. OdometerC. Tripmeter
The trip computer includes the followinginformation displays:
Average fuel
Average speed
Outside air
Reset Trip
Dist. to empty
E74441
Press the up and down arrow buttonson the steering wheel to scroll throughthe trip computer displays.
Note: The position of the trip computerdisplay may vary depending on theinformation shown in the display.
Resetting the trip computer usingthemainmenu
To reset a particular display:
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. Highlight Reset Trip with the up anddown arrow buttons and press theright arrow button.
3. Highlight the function to be reset.
4. Press the right arrow button to selectthe function.
5. Hold the OK button pressed.
To reset all three displays, select Allvalues and hold theOK button pressed.
Type3
E88049A
Trip computerA
Press the OK button on the steeringwheel to cycle through the different tripcomputer displays. To reset a value, pressand hold the OK button.
Resetting the trip computer usingthemainmenu
To reset a particular display:
1. HighlightTripComputerwith the upand down arrow buttons and pressthe right arrow button.
89
Information displays
2. Highlight the function to be reset.
3. Hold the OK button pressed.
PERSONALISEDSETTINGS
The following information is displayed inthe information display if you haveselected it:
Help screen, radio, navigationand phone information
The help screen appears for a fewseconds when you switch the ignition on.
If the radio, navigation or telephone isoperating, information relating to thissystem is displayed in the informationdisplay.
To select which information is displayedin the information display:
Type 1 and2
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightDisplay and press the rightarrow button.
4. Highlight Configure and press theright arrow button.
5. To toggle the Help screen, RadioInfo and Phone Info on and off,highlight the desired setting and pressthe OK button to confirm the setting.
6. Press the left arrow button to exit themenu. Hold the left arrow buttonpressed to return to the trip computerdisplay.
Type3
1. Highlight Settings with the up anddown arrow buttons and press theright arrow button.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightDisplay and press the rightarrow button.
4. Highlight Configure and press theright arrow button.
5. To toggle theHelpscreen andNAVInfo on and off, highlight the desiredsetting and press the OK button toconfirm the setting.
Navigation information
You can also choose when the navigationinformation is displayed in the informationdisplay. Three options are available:
• Always off: No navigationinformation is displayed in theinformation display.
• Onguidance: The navigationinformation will only appear when thenavigation system provides aguidance instruction. This function isonly available on certain navigationsystems.
• Always on: Navigation informationwill always appear in the informationdisplay when the navigation system isoperating.
To set when navigation information shouldbe displayed:
Type 1 and2
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
90
Information displays
3. HighlightDisplay and press the rightarrow button.
4. Highlight Configure and press theright arrow button.
5. HighlightNavInfo and press the rightarrow button.
6. Highlight the desired setting and pressthe OK button to confirm the setting.
7. Press the left arrow button to exit themenu. Hold the left arrow buttonpressed to return to the trip computerdisplay.
Type3
1. Highlight Settings with the up anddown arrow buttons and press theright arrow button.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightDisplay and press the rightarrow button.
4. Highlight Configure and press theright arrow button.
5. HighlightNavInfo and press the rightarrow button.
6. Highlight the desired setting and pressthe OK button to confirm the setting.
Language
A choice of eleven languages areavailable:
English, German, Italian, French, Spanish,Turkish, Russian, Dutch, Polish, Swedishand Portuguese.
Type 1 and2
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightDisplay and press the rightarrow button.
4. Highlight Language and press theright arrow button.
5. Highlight the desired setting and pressthe OK button to confirm the setting.
6. Press the left arrow button to exit themenu. Hold the left arrow buttonpressed to return to the trip computerdisplay.
Type3
1. Highlight Settings with the up anddown arrow buttons and press theright arrow button.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightDisplay and press the rightarrow button.
4. Highlight Language and press theright arrow button.
5. Highlight the desired setting and pressthe OK button to confirm the setting.
Units ofmeasure
Note: The outside air temperature is onlydisplayed in degrees Celsius and cannotbe set to degrees Fahrenheit.
To select metric or imperial units:
Type 1 and2
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
91
Information displays
3. HighlightDisplay and press the rightarrow button.
4. Highlight MeasureUnit and pressthe right arrow button.
5. Highlight the desired setting and pressthe OK button to confirm the setting.
6. Press the left arrow button to returnto exit the menu. Hold the left arrowbutton pressed to return to the tripcomputer display.
Type3
1. Highlight Settings with the up anddown arrow buttons and press theright arrow button.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightDisplay and press the rightarrow button.
4. Highlight MeasureUnit and pressthe right arrow button.
5. Highlight the desired setting and pressthe OK button to confirm the setting.
INFORMATIONMESSAGES
E70499
Press OK to acknowledge and removesome messages from the informationdisplay. Other messages will be removedautomatically after a short time.
With instrument cluster type 3, certainmessages need to be confirmed beforeyou can access the menus.
Message indicator
The message indicatorilluminates to supplement somemessages. It will be red or
amber depending on the severity of themessage and will remain on until thecause of the message has been rectified.
Message symbols
See Owner’s handbook.
Have the system checked atthe next service.
Have the system checked assoon as possible.
Stop your vehicle as soon as itis safe to do so.
Viewing currentmessages
Type 1 and2
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. Highlight Information with the upand down arrow buttons and pressthe right arrow button.
3. Highlight Messages and press theright arrow button.
4. Use the up and down buttons to viewthe current messages.
Type3
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
92
Information displays
2. Highlight Settings with the up anddown arrow buttons and press theright arrow button.
3. Highlight Information with the upand down arrow buttons and pressthe right arrow button.
4. Highlight Messages and press theright arrow button.
5. Use the up and down buttons to viewthe current messages.
Active suspension
MeaningMessagewarning lamp
Message
The active suspension has malfunctioned. Havethis checked as soon as possible. See Using
active suspension (page 146).
amberIVDC malfunction
The active suspension is set to the comfortsetting.
-IVDC comfort
The active suspension is set to the normalsetting.
-IVDC normal
The active suspension is set to the sport setting.-IVDC sport
Alarm
MeaningMessagewarning lamp
Message
The alarm has been triggered. Check yourvehicle for signs of unauthorised access.
amberAlarm triggered
The alarm has malfunctioned. Have this checkedas soon as possible.
-Alarm systemservice reqd.
93
Information displays
Battery and charging system
MeaningMessagewarning lamp
Message
The charging system voltage is above its normaloperating range. Stop your vehicle as soon as
it is safe to do so and switch off the ignition.Have this checked as soon as possible.
red
Overvoltage: Stopsafely!
The battery voltage is low. Have this checkedas soon as possible.
amberLow battery
Climate control
MeaningMessagewarning lamp
Message
The auxiliary heater is on.amberAux. Heater on
Cruise control andAdaptive cruise control (ACC)
MeaningMessagewarning lamp
Message
Cruise control is on.-Cruise controlactive
Cruise control is on standby.-Cruise controlstandby
Stability control (ESP) may be switched off.Switch ESP back on and try ACC again. Other-wise try switching the ignition off and on to clear
this message.
-ACC unavailable
The ACC has malfunctioned. Have this checkedas soon as possible.
amberACC malfunction
There may be something blocking the radarsensor. Clear any dirt, snow, water or other
objects from the front grille area.
amberClean radar sensor
Forward alert has malfunctioned. Have thischecked as soon as possible.
amberForward Alertmalfunction
94
Information displays
Doors open
MeaningMessagewarning lamp
Message
The driver side front door is open.redDriver door open
The driver side rear door is open.redDriver side reardoor open
The passenger side front door is open.redPassenger dooropen
The passenger side rear door is open.redPassenger siderear door open
The luggage compartment is open.redLuggage comp.open
The bonnet is open.redBonnet open
Engine immobiliser
MeaningMessagewarning lamp
Message
The engine immobiliser is on. See Engineimmobiliser (page 43).
amberImmobiliser active
Hill launch assist (HLA)
MeaningMessagewarning lamp
Message
HLA has malfunctioned. Have this checked assoon as possible.
amberHill Launch notavailable
HLA is on.-Hill Launch Assistactive
HLA is off.-Hill Launch Assistoff
HLA is deactivated due to a malfunction. Usethe parking brake normally on hills. See Hill
start assist (page 143).
amberPlease use parkbrake !
95
Information displays
Keyless system
MeaningMessagewarning lamp
Message
The steering system has malfunctioned. Havethis checked as soon as possible.
redSteering malfunc-tion
A valid passive key has not been recognised.amberKey not detected
The engine is still running. Switch the ignition off.See Keyless starting (page 127).
amberCar operativePress STOP
A valid passive key has not been detected insidethe vehicle.
amberKey outside car
Change the battery as soon as possible.amberKey battery low
The steering lock is still active. Press the startbutton.
-Steering locked -Retry
Lighting
MeaningMessagewarning lamp
Message
The adaptive front lighting system (AFS) hasmalfunctioned. Have this checked as soon as
possible.
amberFront lightsmalfunction
One or both of the headlamp dipped beambulbs have blown. Check the headlamp dippedbeam bulbs. SeeChangingabulb (page 60).
-Low beam: Bulbfault
One or both of the rear fog lamp bulbs haveblown. Check the rear fog lamp bulbs. See
Changing a bulb (page 60).
-Rear fog light: Bulbfault
One or both of the brake lamp bulbs have blown.Check the brake lamp bulbs. See Changing
a bulb (page 60).
-Stop lamps: Bulbfault
One or both of the brake lamp bulbs on yourtrailer have blown. Check the brake lamp bulbs
on your trailer.
-Trailer stopl.: Bulbfault
One or both of the direction indicator bulbs onyour trailer have blown. Check the direction
indicator bulbs on your trailer.
-Trailer turnl.: Bulbfault
96
Information displays
Maintenance
MeaningMessagewarning lamp
Message
The engine system has malfunctioned. Havethis checked as soon as possible.
redEngine malfunction
The engine oil level is low. Check the engine oillevel as soon as possible. See Engine oil
check (page 197).
amberCheck engine oillevel
There is water in the fuel. Have this checked assoon as possible.
amberWater detected infuel
The washer fluid level is low. Check the washerfluid level. See Washer fluid check (page
199).
-Low washer fluidlevel
The engine oil needs to be changed. Have theengine oil changed as soon as possible.
-Service oil
Occupant protection
MeaningMessagewarning lamp
Message
Have the system checked as soon as possible.-Crash mode
Parking brake
MeaningMessagewarning lamp
Message
Release the brake when driving. Failure to do sowill result in the rear brakes overheating.
amberPark brakeapplied
Release the brake when driving. Failure to do sowill result in the rear brakes overheating.
redPark brakeapplied
97
Information displays
Power steering
MeaningMessagewarning lamp
Message
The power steering system has malfunctioned.Have this checked as soon as possible.
amberPower steeringmalfunction
Stability control (ESP)
MeaningMessagewarning lamp
Message
Stability control is off.-ESP off
Stability control has malfunctioned. Have thischecked as soon as possible.
-ESP malfunction
Transmission
MeaningMessagewarning lamp
Message
The transmission has malfunctioned. Have thischecked as soon as possible.
redTransmissionmalfunction
The transmission is over heating. Have thischecked as soon as possible.
amberTransmission over-temperatur
Tyre pressuremonitoring system
MeaningMessagewarning lamp
Message
The tyre indicated has continued to deflate.Check the tyre and inflate it to the recom-
mended pressure. SeeTechnicalspecifica-tions (page 219).
redCheck ..... tyre!
One or more of the tyres are significantly under-inflated. This message may be displayed aftera new sensor has been installed. Check thetyres and inflate them to the recommendedpressure. See Technical specifications
(page 219).
redCheck tyre pres-sures
98
Information displays
MeaningMessagewarning lamp
Message
The tyre indicated is significantly under-inflated.Check your tyres and inflate them to the
recommended pressure. See Technicalspecifications (page 219).
amberCheck ..... tyre
You have installed a temporary spare wheel.Install a correctly inflated full size wheel with a
sensor as soon as possible. When a malfunctionoccurs, the system may not be able to detect
or signal low tyre pressure.
amberTyre monitormalfunction
Up to three sensors have malfunctioned, anunapproved accessory is interfering with the
system or a general malfunction has beendetected. Have the system checked as soonas possible. When a malfunction occurs, the
system may not be able to detect or signal lowtyre pressure.
The tyre pressures are not suitable for drivingat 160 km/h (100 mph). Inflate the tyres to the
recommended pressure. See Technicalspecifications (page 219). This message willbe displayed for only a few seconds with a low
tyre pressure warning.
amberInflate tyres for highspeed
You have installed wheels and tyres that do nothave sensors. The tyre pressures will not be
monitored.
-Tyre sensors notdetected
All sensors have malfunctioned or an unap-proved accessory is interfering with the system.
Have this checked as soon as possible.
99
Information displays
Voice control
MeaningMessagewarning lamp
Message
Voice control is on.-Voice controlPlease speak
Check voice control.-Voice control Notrecognised
Voice control is not allowed in this mode.-Voice control Notallowed
100
Information displays
PRINCIPLEOFOPERATION
Outside air
Keep the air intakes forward of thewindscreen free from obstruction (snow,leaves etc.) to allow the climate controlsystem to function effectively.
Recirculated air
CAUTION
Prolonged use of recirculated air maycause the windows to mist up. If thewindows mist up, follow the settings
for defrosting and demisting thewindscreen.
The air currently in the passengercompartment will be recirculated. Outsideair will not enter the vehicle.
Heating
Heating performance depends on thetemperature of the engine coolant.
Air conditioning
Note: The air conditioning operates onlywhen the temperature is above 4ºC(39ºF).
Note: If you use the air conditioning, thefuel consumption of your vehicle will behigher.
Air is directed through the evaporatorwhere it is cooled. Humidity is extractedfrom the air to help keep the windows freeof mist. The resulting condensation isdirected to the outside of the vehicle andit is therefore normal if you see a smallpool of water under your vehicle.
General information oncontrolling the interior climate
Fully close all the windows.
Warming the interior
Direct the air towards your feet. In cold orhumid weather conditions, direct someof the air towards the windscreen and thedoor windows.
Cooling the interior
Direct the air towards your face.
AIR VENTS
Front air vents
E71942
Rear air vents
BA
E89129
OpenA
CloseB
101
Climate control
MANUALCLIMATECONTROL
Air distribution control
A
F B
C
D
E
E71379
WindscreenA
Footwell and windscreenB
FootwellC
Face level and footwellD
Face levelE
Face level and windscreenF
You can set the air distribution control toany position between the symbols.
Blower
E75470
A
OffA
Note: If you switch the blower off, thewindscreen may mist up.
Recirculated air
Press the button to toggle betweenoutside air and recirculated air.
Heating the interior quickly
E71377
102
Climate control
Ventilation
E71378
Set the air distribution control, blower andair vents to suit your requirements.
Air conditioning
Switching the air conditioning onand off
If you turn the blower off, the airconditioning will turn off. When you turnthe blower on again, the air conditioningwill come on automatically.
Coolingwith outside air
E71380
Cooling the interior quickly
E71381
Defrosting and demisting thewindscreen
E71382
When the temperature is above 4°C(39°F), the air conditioning will switch onautomatically. Make sure that the bloweris on. The indicator in the switch willilluminate during defrosting and demisting.
If you move the air distribution control toa position other than A, the A/C willremain on.
You can switch the air conditioning andrecirculated air on and off while the airdistribution control is set to position A.
If necessary, switch the heated windowson. See Heatedwindows andmirrors (page 106).
103
Climate control
Reducing interior air humidity
E71383
AUTOMATICCLIMATECONTROL
E80737
The system controls the temperature,amount and distribution of the air flowautomatically and adjusts them accordingto the driving and weather conditions.Press the AUTO button to switch automode on.
The system in your vehicle is dual-zoneautomatic climate control. When thesystem is in mono mode, all thetemperature zones are linked to thedriver's zone. When you switch monomode off, the dual-zone system allowsyou to set different temperatures for thedriver's and front passenger's side.
Note: Avoid adjusting the settings whenthe vehicle interior is extremely hot orcold. The automatic climate controladjusts to the current circumstancesautomatically. For the system to functionproperly, the side and centre vents shouldbe fully open.
Note:At low outside temperatures, whenthe system is in auto mode, the air streamwill be directed to the windscreen and theside windows as long as the engine iscold.
104
Climate control
Note: For information on the automaticclimate control, on vehicles fitted with acombined Navigation and automaticclimate control system, see separatehandbook.
Setting the temperature
E70304
You can set the temperature between16ºC (61ºF) and 28ºC (82ºF) in steps of0.5ºC (1ºF). In position LO (below 16ºC[61ºF]) the system will switch topermanent cooling, in position HI (above28ºC [82ºF]) to permanent heating, andwill not regulate a stable temperature.
Monomode
In mono mode, the temperature settingsfor both the driver’s and passenger’s sideare linked. If you adjust the temperatureusing the rotary control on the driver’sside, the same temperature will be set forthe passenger’s side. MONO is shownin the display.
To switchmonomodeoff
Select a temperature for the passenger’sside using the rotary control on thepassenger’s side. Mono mode will switchoff and MONO disappears from thedisplay. The temperature for the driver’sside will remain unchanged. You can nowadjust the driver's and passenger's sidetemperatures independently of eachother. The temperatures are shown in thedisplay. You can set a difference of up to4ºC (7ºF).
Note: If you set a difference of greaterthan 4°C (7ºF), the temperature on theother side will be adjusted so that thedifference remains at 4°C (7ºF).
Note: If you set one of the sides toHI orLO, both sides will be set to HI or LO.
To switchmonomodeback on
Press the MONO button. MONO isshown in the display, and the passenger’sside temperature will be adjusted to thedriver’s side temperature.
Blower
High speed
Lowspeed
Use the buttons to adjust the blowerspeed.
The blower setting is shown in the display.
To return to auto mode, press theAUTObutton.
Air distribution
To adjust air distribution, press the desiredbutton. Any combination of settings canbe selected simultaneously.
105
Climate control
E70308
A B C
FootwellA
Face levelB
WindscreenC
Windscreen defrosting anddemisting
When you select windscreen defrostingand demisting, A, B and C switch offautomatically and the air conditioningswitches on. Outside air will flow into thevehicle. You cannot select recirculatedair.
The blower speed and the temperaturecontrol operate automatically and cannotbe adjusted manually. The blower is setto high speed and the temperature toHI.
When you select windscreen defrostingand demisting, the heated screens switchon automatically and switch off after ashort time.
To return to auto mode, press theAUTObutton.
Note: To defrost or demist the rear sidewindows, adjust the rear air vents. SeeAir vents (page 101).
Switching the air conditioningon and off
Press the button.A/COFF orA/CON isshown in the display.
Recirculated air
Press the button to change betweenautomatic mode and recirculated air.
Note: When the system is in auto modeand the interior and exterior airtemperatures are quite hot, the systemselects recirculated air automatically tomaximise cooling of the interior. Once theselected temperature is reached, thesystem will automatically reselectautomatic mode.
Switching the automaticclimate control on and off
E70980
Use the buttons to switch the system onand off.
When switched off, the heating, ventilationand air conditioning system is switchedoff and recirculated air is selected.
HEATEDWINDOWSANDMIRRORS
Heatedwindows
Use the heated windows to defrost ordemist the windscreen or rear window.
Note: The heated windows operate onlywhen the engine is running.
106
Climate control
Heatedwindscreen
E72506
Heated rearwindow
E72507
Heated exteriormirrors
Electric exterior mirrors are fitted with aheating element that will defrost or demistthe mirror glass. They will switch onautomatically when you switch the heatedrear window on.
AUXILIARYHEATER
Parking heater
WARNING
The parking heater must not beoperated at filling stations, nearsources of combustible vapours or
dust or in enclosed spaces.
The parking heater operatesindependently of the vehicle heater byheating the engine’s coolant circuit. It isfed from the vehicle fuel tank. You canalso use it while the vehicle is in motion tohelp the vehicle heater warm up theinterior more quickly.
Used properly, the parking heaterprovides the following benefits:
• It preheats the interior of the vehicle.
• It keeps the windows clear of ice inthe event of frost and preventscondensation.
• It avoids cold starts and allows theengine to reach operatingtemperature sooner.
Note: The parking heater will onlyoperate if there is at least 7.5 litres (1.6gallons) of fuel in the fuel tank and theambient temperature is below 15°C(59°F). The heater will not operate if thebattery is low.
Note: The heating depends on theoutside air temperature.
Note: When the parking heater isactivated, exhaust fumes may come fromunder the sides of the vehicle. This isnormal.
Note:On vehicles with a manual heating,ventilation and air conditioning system,the heating of the vehicle interior isdependent on the temperature, airdistribution and blower control settings.
To prevent the battery from discharging:
• Once the parking heater hasperformed one heating cycle, the nextprogrammed heating cycle will onlybe carried out if you have started thevehicle’s engine in between.
• After a heating cycle, drive the vehiclefor at least the period of the heatingcycle.
Programming the parking heater
Note: The programmed time is the timeat which you wish the vehicle to be warmand ready to drive, not the time at whichthe heater switches on.
Note: You must programme the timesat least 70 minutes in advance of the timeyou wish to set.
Note: You must set the time and datecorrectly. See Clock (page 121).
To programme the heating times:
107
Climate control
E70499
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightParkHeater and press theright arrow button.
E74467
One-Time
Program 1Program 2
Active now
Park Heater
• The functions Program 1 andProgram2 allow you to programmeup to two heating cycles for each dayof the week. These times will remainstored and the heater will warm up thevehicle at these times on these daysevery week.
• The function One-Time allows youto programme one heating cycle forone specific day.
• The function Active nowautomatically switches on the heater.
Programming the functionsProgram 1 andProgram2
E74468
FridayThursday
TuesdayMonday
Wednesday
[07:55]
Program 1
1. Highlight Program 1 and press theright arrow button.
2. Highlight the day on which the heatershould warm up the vehicle.
3. Press the OK button to confirm theselection. A cross appears in the boxnext to the day to show that this dayis selected.
4. Continue in the same way to select allthe days on which the heater shouldwarm up the vehicle.
108
Climate control
5. To set the time at which the vehicleshould be warmed up, highlight thetime at the top of the display andpress the right arrow button.
6. Press the OK button and the hoursflash. Use the up and down arrowbuttons to adjust the individual settingsand the left and right arrow buttons tomove to the next or previous setting.
7. When you have finished, press theOKbutton again to confirm the selection.
E74469
07:5501:12:2006
ParkheaterProgram 1
OK = change
You can use the function Program2 toset a second cycle, for example differenttimes on different days or twice on thesame day. The programming procedureis the same as for the functionProgram1.
Programming the functionOne-Time
1. Highlight One-Time and press theright arrow button.
2. Press the OK button and the hoursflash. Use the up and down arrowbuttons to adjust the individual settingsand the left and right arrow buttons tomove to the next or previous setting.
3. When you have finished, press theOKbutton again to confirm the selection.
Active now
HighlightActivenow and press theOKbutton. A cross appears in the box nextto the function to show that the heater isactivated.
To deactivate the heater, highlightActivenow and press the OK button again.
Diesel auxiliary heater(depending on country)
The diesel auxiliary heater (PTC electricalheater) aids in warming the engine andthe vehicle interior on vehicles with adiesel engine. It is switched on or offautomatically depending on the outsideair temperature, the coolant temperatureand the alternator load.
Fuel operated heater(depending on country)
The fuel operated heater aids in warmingthe engine and the vehicle interior onvehicles with a petrol or diesel engine. Itis switched on or off automaticallydepending on the outside air temperatureand the coolant temperature, unless youhave deactivated it. When the fueloperated heater is operating, Aux.Heateron is displayed in the informationdisplay. See Information displays(page 79).
To deactivate the fuel operated heater:
E70499
109
Climate control
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downarrow buttons and press the rightarrow button.
3. HighlightAux.Heater and press theOKbutton to toggle the heater on andoff. A cross appears in the box whenthe heater is activated.
4. Press the left arrow button to exit themenu. Hold the left arrow buttonpressed to return to the trip computerdisplay.
Remote starting
The parking heater may be started andswitched off from a distance of up to 500metres (1640 feet) using the suppliedremote control transmitter. This range willvary depending upon local conditions andterrain, as well as battery condition. Theremote control transmitter will indicatewhether or not the signal has beenreceived. The parking heater will operatefor a maximum of 50 minutes.
Starting
Hold the transmitter with the antennaupwards and press the ON button for 1 -2 seconds. The LED on the transmitterlights up green to confirm the signal hasbeen received.
Switching off
Hold the transmitter with the antennaupwards and press the OFF button for 1- 2 seconds. The LED on the transmitterlights up red to confirm the signal hasbeen received.
Remote start in combinationwith direct start or timer
E114360
Remote start is integrated with normalheater control. Parking heaters startedwith direct start or timer functions can beswitched off with the remote controltransmitter and vice versa.
Feedback during starting andswitching off
The LED on the transmitter illuminatesgreen for about two seconds. Thisindicates the signal has been received bythe vehicle and the heater has started.
The LED on the transmitter illuminates redfor about two seconds. This indicates thesignal has been received by the vehicleand the heater has switched off.
The LED on the transmitter flashes greenor red for about two seconds. Thisindicates the signal was not transmittedcorrectly. Repeat the transmission.
Note: Transmitter range is dependantupon distance and local conditions suchas buildings, etc.
The LED on the transmitter illuminatesorange for about two seconds beforeshowing green or red. This indicates thetransmitter batteries are weak and shouldbe changed.
110
Climate control
The LED on the transmitter flashes orangefor about 5 seconds. This indicates thatthe signal was not transmitted. Thetransmitter batteries are discharged andshould be changed as soon as possible.
Changing the remote controlbattery
Make sure that you dispose of oldbatteries in an environmentally friendlyway. Seek advice from your local authorityregarding recycling.
E114361
2
1
1. Insert a screwdriver or other suitabletool into the slot on the back of theremote control, and unscrew thecompartment cover.
CAUTION
Do not touch the battery contacts orthe printed circuit board with thescrewdriver.
2. Carefully prise out the battery.
3. Install a new battery (3.3V typeCR1-3N) with the + facing upwards.
4. Re-assemble the remote control.
Programming the transmitter
Further transmitters may be used with theremote system, please consult yourdealer. Up to a maximum of 3 separateremote controls may be added. Whenadding extra transmitters these must beprogrammed separately.
Note: The heater must be switched offduring programming.
Note:The programming procedure maybe repeated as often as is required. Theoldest programmed transmitter will bedeleted each time.
1. Install the battery in the newtransmitter.
2. Turn off the power to the receiver byremoving fuse F32 from the enginecompartment fuse box. See Fusespecification chart (page 176).
3. Wait for at least 5 seconds.
4. Reconnect power to the receiver byreplacing the fuse, and press the OFFbutton on the new transmitter within5 seconds until the LED light turns off.
5. The new transmitter is nowprogrammed.
ELECTRICSUNROOF
E78054
111
Climate control
WARNING
Before operating the electricsunroof you should verify it is free ofobstructions and ensure that
children and/or pets are not in theproximity of the sunroof opening. Failureto do so could result in serious personalinjury. It is the primary responsibility of thesupervising adults to never leave a childunattended in a vehicle and to never leavethe keys in an unattended vehicle.
Note: When the switches are operatedoften during a short period of time, thesystem might become inoperable for acertain time to prevent damage due tooverheating.
Note: The electric sunroof can also beoperated with the ignition off via the globalopening and global closing function. SeeGlobal opening and closing (page38).
There are two ways of opening thesunroof – the rear of the sunroof lifts openor the sunroof opens from the front,sliding back under the roof. The sunroofopens and closes whilst the switch ispressed.
Switch on the ignition to operate theelectric sunroof.
The power sunroof is operated by aswitch located between the sun visors.
Opening and closing thesunroof
E72188
E72185
B
A
Press to closeA
Press to openB
112
Climate control
Tilting the sunroof
E72189
E72185
B
A
Press to openA
Press to closeB
Opening and closing thesunroof automatically
Note: When opening automatically, thesunroof will stop about 8 cm from the fullyopened position. This position reducesthe buffeting noise which is sometimesheard when the sunroof is fully open. Thesunroof will only stop automatically in thisposition when the sunroof is openedautomatically.
To open or close the sunroofautomatically press either side of theswitch to the second action point andrelease it completely. Press again to stop.
When the closed position is reached, thesunroof stops automatically.
Sunroof anti-trap protection
WARNINGSThe anti-trap function is deactivateduntil the memory has been reset.Careless closing of the window can
cause injuries.
Careless closing of the electricsunroof can override the anti-trapprotection and cause injuries.
The sunroof will stop automatically whileclosing and reverse some distance if thereis an obstacle in the way.
To override anti-trap protection whenthere is a resistance, e. g. in the winter,proceed as follows:
WARNING
While the sunroof is being closed forthe third time, the anti-trap functionis disabled. Make sure there are no
obstacles in the way of the closingsunroof.
Close the sunroof a third time to theresistance. The anti-trap function isdisabled and the sunroof cannot beclosed automatically. The sunroof willoverride the resistance and can then beclosed fully.
If the sunroof does not close after thethird attempt, have it checked by anexpert.
113
Climate control
Sunroof safetymode
WARNING
The anti-trap function is not activeduring this procedure. Make surethat there are no obstacles in the
way of the closing sunroof.
If the system detects a malfunction, itenters a safety mode. The sunroof willmove for only about 0.5 seconds at a timeand then stop again. Close the sunroofby pressing the button again when thesunroof stops moving. When the rear ofthe sunroof is lifted, lift the rear all the wayand then close the sunroof. Have thesystem checked by an expertimmediately.
Sunroof relearning
WARNING
The anti-trap function is not activeduring this procedure. Make surethat there are no obstacles in the
way of the closing sunroof.
In case the sunroof no longer closesproperly, follow this relearning procedure:
• Tilt the rear of the sunroof as far aspossible. Release the button.
• Press and hold the same button againfor 30 seconds until you see thesunroof move.
• Release the button and immediatelypress and hold it again. The sunroofwill close, open fully and then closeagain. Do not release the buttonbefore the sunroof has reached theclosed position for the second time.
If the button is not pressed continuously,the relearning function will be interrupted.Start the procedure once more from thebeginning.
114
Climate control
SITTING IN THECORRECTPOSITION
E68595
WARNINGSDo not adjust the seats when thevehicle is moving.
Only when you use the seat beltproperly, can it hold you in a positionthat allows the airbag to achieve its
optimum effect.
When you use them properly, the seat,head restraint, seat belt and airbags willprovide optimum protection in the eventof a collision. We recommend that you:
• sit in an upright position with the baseof your spine as far back as possible.
• do not recline the seatback more than30 degrees.
• adjust the head restraint so that thetop of it is level with the top of yourhead and as far forwards as possible,remaining comfortable.
• keep sufficient distance betweenyourself and the steering wheel. Werecommend a minimum of 250millimetres (10 inches) between yourbreastbone and the airbag cover.
• hold the steering wheel with your armsslightly bent.
• bend your legs slightly so that you canpress the pedals fully.
• position the shoulder strap of the seatbelt over the centre of your shoulderand position the lap strap tightlyacross your hips.
Make sure that your driving position iscomfortable and that you can maintain fullcontrol of your vehicle.
MANUALSEATS
Moving the seats backwardsand forwards
E70728
WARNING
Rock the seat backwards andforwards after releasing the lever tomake sure that it is fully engaged in
its catch.
115
Seats
Adjusting the lumbar support
E70729
Adjusting the height of thedriver’s seat
E70730
Adjusting the angle of theseatback
E70731
ELECTRICSEATS
2-way electric seat
E70733
1
1
2
2
116
Seats
8-way electric seat
12 2 1 3
4
3
4
8 7
8 7
5
6
5
6E70734
117
Seats
HEADRESTRAINTS
Adjusting the head restraint
WARNINGSRaise the rear head restraint whenthe rear seat is occupied by apassenger.
When using a forward facing childrestraint on a rear seat, alwaysremove the head restraint from that
seat.
E71879
Adjust the head restraint so that the topof it is level with the top of your head andas far forwards as possible, remainingcomfortable.
Removing the head restraint
Press the locking buttons and remove thehead restraint.
REARSEATS
WARNINGSWhen folding the seatbacks down,take care not to get your fingerscaught between the seatback and
seat frame.
Make sure that the seats and theseatbacks are secure and fullyengaged in their catches.
Folding the seatbacks down
CAUTION
Lower the head restraints.
1
2
1
E86611
1. Press the unlock buttons down andhold them there.
2. Push the seatback forwards.
Creating a level load floor
WARNING
Make sure the red indicator is notshowing when you engage the seatin the catches.
118
Seats
CAUTION
Lower the head restraints.
2
13
2
E86612
1. Insert your fingers between the seatcushion and seatback and fold theseat cushion forwards.
2. Press the unlock buttons down andhold them there.
3. Push the seatback forwards.
Folding the seatbacks up
WARNING
When folding the seatbacks up,make sure that the belts are visibleto an occupant and not caught
behind the seat.
HEATEDSEATS
CAUTION
Operating this function with theengine off will drain the battery.
E70601
E71224
Note: The settings are stored when youswitch off the ignition.
VENTILATEDSEATS
CAUTION
Operating this function with theengine off will drain the battery.
119
Seats
E70601
E70602
Note: The settings are stored when theignition is switched off.
Note: When the seat is being ventilated,the heater may switch on automatically.This is to prevent the flow of air becominguncomfortably cool.
Note: The air in the vehicle interior is usedto ventilate the seats. The cooling effecttherefore depends on the temperatureof the vehicle interior. Switch on the airconditioning if necessary and set the airdistribution to footwell. See Climatecontrol (page 101).
120
Seats
SUNBLINDS
Pull the blind up and attach it to the hooks(A).
Sidewindows
E74809
AA
Rearwindow
AA
E86514
INSTRUMENT LIGHTINGDIMMER
E70723
CLOCK
Note: Some navigation systems willautomatically set the date and time on theclock using GPS signals.
Note: SeeGeneral information (page79).
1. From the main menu, select the clockfunction.
2. Select the option required.
3. Press OK.
4. Using the right, left, up and downarrow buttons, select and change thevalue.
5. Press OK.
CIGAR LIGHTER
CAUTIONSIf you use the socket when theengine is not running, the batterymay discharge.
Do not hold the cigar lighter elementpressed in.
121
Convenience features
Note: Switch the ignition on to use thecigar lighter. You can also use it for up to30 minutes after you have switched theignition off.
Note: You can use the socket to power12 volt appliances that have a maximumcurrent rating of 15 Amperes. Use onlyFord accessory connectors or connectorsspecified for use with SAE standardsockets.
E72972
Press the element in to use the cigarlighter. It will pop out automatically.
ASHTRAY
Front ashtray
E72974
To empty, pull out the complete ashtray.
Rear ashtray
E73705
To remove the ashtray, open it, press itdown against the spring and remove it.
AUXILIARYPOWERSOCKETS
CAUTION
If you use the socket when theengine is not running, the batterymay discharge.
Note: You can use the socket when theignition is switched off.
Note: You can use the socket to power12 volt appliances that have a maximumcurrent rating of 15 Amperes. Use onlyFord accessory connectors or connectorsspecified for use with SAE standardsockets.
122
Convenience features
E86470
CUPHOLDERS
WARNING
Do not place hot drinks in the cupholders when the vehicle is moving.
GLOVEBOX
Cooled glove box
Note: You can cool the glove box usingair from the air conditioning system.
E70885
STORAGECOMPARTMENTS
WARNING
Do not drive with any storagecompartment lid open. Make surethat you secure the lid before
setting off.
CAUTION
Do not keep heat-sensitive items andliquids in any storage compartment.
E72980
E73704
123
Convenience features
E72905
E72905
MAPPOCKETS
E74686
MEMORYFUNCTION
WARNINGSBefore activating the seat memory,make sure that the area immediatelysurrounding the seat is clear of
obstructions and that all occupants areclear of moving parts.
Do not use the memory storefunction when the vehicle is moving.
A
B
E86768
Seat adjustment controls SeeElectric seats (page 116).
A
Memory pre-set buttonsB
Up to four different driver's seat andexterior mirror positions can be stored inthe memory. Your preferred setting forthe reverse mirror dipping feature can alsobe stored. See Electric exteriormirrors (page 71).
Setting amemory pre-set
Passive setting
The vehicle stores the seating and mirrorpositions for up to four remote controlsor passive keys. Next time the vehicle isunlocked, the position of the seat andmirrors will adjust to the last used position.
Each time you turn the ignition off, thecurrent seat and mirror settings are storedon the remote control or passive keyused.
Active setting
1. Turn the ignition on.
2. Adjust the seat and exterior mirrors tothe desired position.
124
Convenience features
3. Press and hold the desired pre-setbutton B until a single chime soundsto confirm.
Recallingastoredseatposition
Note: To stop seat movement during arecall, press any driver seat adjustmentcontrol, any of the memory buttons or anymirror control switch. Seat movement willalso stop if you move the vehicle.
Passive recall
Note: If more than one passive key is inrange, the memory function will move tothe settings of the first key stored.
When you unlock the vehicle with theremote control or pull the driver doorhandle with a passive key in range, theseat and mirrors will move to the positionstored on that remote control or passivekey.
Active recall
Press the pre-set button associated withthe desired driving position. The seat andmirrors will move to the position storedon that pre-set.
GLASSESHOLDER
E75193
CDCHANGER
This is located in the luggagecompartment.
AUXILIARY INPUT (AUX IN)SOCKET
E71969
See separate audio handbook.
125
Convenience features
USBPORT
E104423
See Connectivity (page 257).
126
Convenience features
GENERAL INFORMATION
General points on starting
If the battery has been disconnected thevehicle may exhibit some unusual drivingcharacteristics for approx. 8 kilometres(5 miles) after reconnecting the battery.
This is because the engine managementsystem must realign itself with the engine.Any unusual driving characteristics duringthis period may be disregarded.
Starting the engine by towingor pushing
WARNING
To prevent damage you must notpush or tow start your vehicle. Usebooster cables and a booster
battery. See Using booster cables(page 204).
IGNITIONSWITCH
WARNING
Never return the key to position 0or I when the vehicle is in motion.
E72128
0 The ignition is off.
I The ignition and all main electrical circuitsare disabled.
Note:Do not leave the ignition key in thisposition for too long to avoid dischargingthe battery.
II The ignition is switched on. All electricalcircuits are operational. Warning lampsand indicators illuminate. This is the keyposition when driving. You must alsoselect it when being towed.
III The starter motor is activated. Releasethe key as soon as the engine starts.
KEYLESSSTARTING
WARNINGSThe keyless starting system may notfunction if the key is close to metalobjects or electronic devices such
as mobile phones.
Always check that the steeringwheel lock is deactivated beforeattempting to move your vehicle.
See Steeringwheel lock (page 129).
Note: A valid passive key must belocated inside the vehicle to switch theignition on and start the engine.
Note: To start your engine you must alsofully depress the brake or clutch pedal,depending on the transmission fitted.
E85766
Ignition on
Press the start button once. All electricalcircuits are operational, warning lampsand indicators illuminate.
127
Starting the engine
Startingwith automatictransmission
Note: Releasing the brake pedal duringengine start will stop the engine crankingand return to ignition on.
1. Make sure the transmission is in P orN.
2. Fully depress the brake pedal.
3. Press the start button.
Startingwithmanualtransmission
Note: Releasing the clutch pedal duringengine start will stop the engine crankingand return to ignition on.
1. Fully depress the clutch pedal.
2. Press the start button.
Starting a diesel engine
Note: Engine cranking may notcommence until the engine glow plugcycle has been completed. This may takeseveral seconds in extremely coldconditions.
Note: Continue to press the clutch orbrake pedal until engine cranking begins.
Failure to start
The passive starting system will notfunction if:• The passive key frequencies are
jammed.• The passive key battery is flat.
If you are unable to start your vehicle carryout the following procedure.
Type 1
E87382
1. Hold the key next to the steeringcolumn shroud exactly as shown.
2. With the key in this position you canuse the start button to switch theignition on and start your vehicle.
Type2
E87381
1. Carefully prise out the cover.
128
Starting the engine
E85767
2. Insert the key into the key holder.
3. With the key in this position you canuse the start button to switch theignition on and start your vehicle.
Stopping the engine
When your vehicle is stationary, press thestart button to stop the engine. Theignition, all electrical circuits, warninglamps and indicators will be switched off.
STEERINGWHEEL LOCK
WARNING
Always check that the steering isunlocked before attempting tomove your vehicle.
Vehicleswithout keylessstarting
To activate the steering wheel lock;
1. Remove the key from the ignitionswitch.
2. Turn the steering wheel.
Vehicleswith keyless starting
Note: The steering wheel lock will notactivate when the ignition is on or thevehicle is moving.
Your vehicle has an electronicallycontrolled steering wheel lock. Thisoperates automatically.
The steering wheel lock will activate aftera short period of time once you haveparked your vehicle and the passive keyis outside of the vehicle.
Deactivating the steeringwheellock
Switch the ignition on, or:
Vehicles with automatic transmission• Press the brake pedal.
Vehicles with manual transmission• Press the clutch pedal.
STARTINGAPETROLENGINE
Note: You can only operate the starterfor a maximum of 30 seconds at a time.
Cold or hot engine
All vehicles
CAUTION
When the temperature is below-20ºC (-4ºF), switch the ignition onfor at least one second before
starting the engine. This will make surethat the maximum fuel pressure isestablished for starting the engine.
Vehicleswithmanual transmission
Note: Do not touch the acceleratorpedal.
1. Fully depress the clutch pedal.
129
Starting the engine
2. Start the engine.
Vehicleswith automatictransmission
Note: Do not touch the acceleratorpedal.
1. Select park or neutral.
2. Fully depress the brake pedal.
3. Start the engine.
All vehicles
If the engine does not start within 15seconds, wait for a short period and tryagain.
If the engine does not start after threeattempts, wait 10 seconds and follow theFlooded engine procedure.
If you have difficulty starting the enginewhen the temperature is below -25ºC(-13ºF), press the accelerator pedalbetween ¼ to ½ of its travel and try again.
Flooded engine
Vehicleswithmanual transmission
1. Fully depress the clutch pedal.
2. Fully depress the accelerator pedaland hold it there.
3. Start the engine.
Vehicleswith automatictransmission
1. Select park or neutral.
2. Fully depress the accelerator pedaland hold it there.
3. Fully depress the brake pedal.
4. Start the engine.
All vehicles
If the engine does not start, repeat theCold or hot engine procedure.
Engineidlespeedafterstarting
The speed at which the engine idlesimmediately after starting will varydepending on the engine temperature.
If the engine is cold then the idle speedwill automatically be increased in order toheat the catalytic converter as quickly aspossible. This ensures that vehicleemissions are kept to an absoluteminimum.
The idle speed will slowly decrease to thenormal level as the catalytic converterwarms up.
STARTINGAPETROLENGINE - E85
For general information on starting apetrol engine. See Starting a petrolengine (page 129).
Starting at lowambienttemperatures
When the temperature is lower than -10°C(14°F) and the vehicle is filled with E85, anengine block heater should be used tofacilitate starting. See Engine heater(page 132). Failure to do this will result in anon start.
If the temperature is expected to remainbelow -10°C (14°F), it is recommendedthat you increase the proportion of petrolin the tank by topping up with 95 octaneunleaded petrol if the tank is not alreadyfull. About 10 litres (2.2 gallons) of petrolwill reduce the proportion of E85 in a ¾full tank from 85% to 70% and willconsiderably improve cold start capability.
If, at very low temperatures, the tank isfilled with only E85 and there is no way touse an engine block heater, you mayexperience difficulties starting the engine.
130
Starting the engine
If the engine fails to start, proceed asfollows:
1. Fully depress the accelerator pedal.
2. Turn the ignition key to position III.
CAUTION
Release the ignition key as soon asthe engine has started.
3. Gradually release the acceleratorpedal after 5 seconds of enginecranking or as the engine speed rises.
If the engine fails to start, repeat steps 1,2 and 3, or connect an engine blockheater for two hours before attemptinganother start.
During starting, the fuel injectors areturned off as long as the accelerator pedalis depressed. This can be used to drainexcessive fuel from the intake manifoldafter several unsuccessful startingattempts.
If the battery has been disconnected orafter the fuel type has been changed, theidle speed may be irregular. This willimprove after 10 to 30 seconds.
STARTINGADIESELENGINE
Cold or hot engine
All vehicles
Note: When the temperature is below-15ºC (5ºF), you may need to crank theengine for up to 25 seconds. If youconsistently operate the vehicle in suchtemperatures, we recommend that youhave an engine block heater fitted.
Note:Continue cranking the engine untilit starts.
Note: You can only operate the starterfor a maximum of 30 seconds at a time.
Switch the ignition on and waituntil the glow plug indicatorgoes off.
Vehicleswithmanual transmission
Note: Do not touch the acceleratorpedal.
1. Fully depress the clutch pedal.
2. Start the engine.
Vehicleswith automatictransmission
1. Select park or neutral.
2. Fully depress the brake pedal.
3. Start the engine.
DIESELPARTICULATEFILTER (DPF)
The DPF forms part of the emissionsreduction systems fitted to your vehicle.It filters harmful diesel particulates (soot)from the exhaust gas.
Regeneration
WARNING
Do not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The DPF
regeneration process creates very highexhaust gas temperatures and theexhaust will radiate a considerableamount of heat during and after DPFregeneration, and after you have switchedthe engine off. This is a potential firehazard.
131
Starting the engine
Unlike a normal filter which requiresperiodic replacement, the DPF has beendesigned to regenerate, or clean itself tomaintain operating efficiency. Theregeneration process takes placeautomatically. However, some drivingconditions mean that you may need tosupport the regeneration process.
If you drive only short distances or yourjourneys contain frequent stopping andstarting, occasional trips with the followingconditions could assist the regenerationprocess:
• Drive your vehicle, preferably on amain road or motorway, for up to 20minutes avoiding prolonged idling, butalways observing speed limits androad conditions.
• Do not switch off the ignition.
• Use a lower gear than normal tomaintain a higher engine speed duringthis journey, where appropriate.
SWITCHINGOFF THEENGINE
Vehicleswith a turbocharger
CAUTION
Do not switch the engine off when itis running at high speed. If you do,the turbocharger will continue
running after the engine oil pressure hasdropped to zero. This will lead topremature turbocharger bearing wear.
Release the accelerator pedal. Wait untilthe engine has reached idle speed andthen switch it off.
ENGINEHEATER
CAUTION
Make sure you disconnect the powercable from the engine heaterconnector before driving away.
Note: The engine heater connector islocated in the radiator grille at the front ofyour vehicle.
E97918
Connect the engine heater for 2 to 3hours before starting the engine.
132
Starting the engine
FUELQUALITY - PETROL
Note:We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.
CAUTION
Do not use leaded petrol or petrolwith additives containing othermetallic compounds (e.g.
manganese-based). They could damagethe emission system.
Use minimum95octane unleadedpetrol that meets the specification definedby EN228, or equivalent.
FUELQUALITY - E85
WARNINGSDo not modify the fuel systemconfiguration or the components inthe system.
Do not replace the fuel system orthe components with parts notspecially designed to be used with
E85.
CAUTIONSDo not use leaded petrol or petrolwith additives containing othermetallic compounds (e.g.
manganese-based). They could damagethe emission system.
Do not use methanol instead of E85.
Note:We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.
Note: When using E85, you mayexperience a higher fuel consumption.
Note: Your vehicle will operate well oncommercial quality 95 octane unleadedpetrol, but only high quality E85 offers thesame protection and performance.
Use minimum95octane unleadedpetrol that meets the specification definedby EN228, or equivalent. You can alsouse a mixture of unleaded petrol and E85.
Long-termstorage
Due to small amounts of corrosiveimpurities that may be found in the E85,it is recommended that you fill the tankwith only 95 octane unleaded petrol priorto long-term storage of your vehicle.
FUELQUALITY - DIESEL
WARNING
Do not mix diesel with oil, petrol orother liquids. This could cause achemical reaction.
CAUTION
Do not add kerosene, paraffin orpetrol to diesel. This could causedamage to the fuel system.
Note:We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.
Note: We do not recommend theprolonged use of additives intended toprevent fuel waxing.
Use diesel that meets the specificationdefined by EN590, or equivalent.
You can use diesel that contains up to 5%RME (bio diesel).
133
Fuel and refuelling
Long-termstorage
Most diesel fuels contain bio-diesel, it isrecommended to fill the tank with purelymineral diesel (where available) or add ananti-oxidant prior to long-term storage ofyour vehicle exceeding two months. Yourdealer can help you with a suitableanti-oxidant.
CATALYTICCONVERTER
WARNING
Do not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The exhaust
will radiate a considerable amount of heatduring use, and after you have switchedthe engine off. This is a potential firehazard.
Drivingwith a catalyticconverter
CAUTIONSAvoid running out of fuel.
Do not crank the engine for longperiods.
Do not run the engine when a sparkplug lead is disconnected.
Do not push-start or tow-start yourvehicle. Use booster cables. SeeUsingboostercables (page 204).
Do not switch the ignition off whendriving.
FUEL FILLER FLAP
WARNINGSTake care when refuelling to avoidspilling any residual fuel from the fuelnozzle.
WARNINGSDo not use any kind of flames orheat near the fuel system. The fuelsystem is under pressure. There is
a risk of injury if the fuel system is leaking.
CAUTION
If you use a high pressure spray towash your vehicle, only spray the fuelfiller flap briefly from a distance not
less than 20 centimetres (8 inches).
Note: Central locking also locks andunlocks the fuel filler flap. See Lockingand unlocking (page 36).
E86613
Press the flap to open it. Open the flapfully until it engages.
When you insert the fuel nozzle, a springloaded inhibitor will open if the correct sizenozzle is detected. This will prevent fillingup with the wrong fuel.
WARNING
Stop refuelling after the fuel nozzlestops the second time. Additionalfuel will fill the expansion space in
the fuel tank which could lead to fueloverflowing. Fuel spillage could behazardous to other road users.
134
Fuel and refuelling
E119080
Insert the fuel nozzle up to and includingthe first notch on the nozzle. Keep itresting on the cover of the fuel pipeopening.
WARNING
We recommend that you wait atleast 10 seconds before removingthe fuel nozzle to allow any residual
fuel to drain into the fuel tank.
E119081
Slightly raise the fuel nozzle to remove it.
Vehicleswith diesel engine
A funnel is located in the spare wheel well.Use this when refilling with a fuel can.
REFUELLING
CAUTION
Do not attempt to start the engine ifyou have filled the fuel tank with theincorrect fuel. This could damage the
engine. Have the system checked by aproperly trained technician immediately.
REFUELLING - E85
CAUTION
Do not attempt to start the engine ifyou have filled the fuel tank with theincorrect fuel. This could damage the
engine. Have the system checked by aproperly trained technician immediately.
After refuelling, allow 5 minutes of normalengine operation above 48 km/h (30mph) to reduce the risk of an increasedengine restart time.
FUELCONSUMPTION
The CO2 and fuel consumption figuresare derived from laboratory testsaccording to EEC Directive 80/1268/EECand subsequent amendments and arecarried out by all vehicle manufacturers.
They are intended as a comparisonbetween makes and models of vehicles.They are not intended to represent thereal world fuel consumption you may getfrom your vehicle. Real world fuelconsumption is governed by many factorsincluding; driving style, high speed driving,stop/start driving, air conditioning usage,the accessories fitted and towing etc.
Your Ford dealer can give you advice onimproving your fuel consumption.
135
Fuel and refuelling
TECHNICALSPECIFICATIONS
4-door and5-door
Fuel consumption figures
CO2emis-sionsCombinedExtra-urbanUrban
Variant
g/kml/100 km(mpg)
l/100 km(mpg)
l/100 km(mpg)
1707.2 (39.2)5.6 (50.4)10 (28.2)1.6L Duratec-Ti-VCT
1897.9 (35.8)6 (47.1)11.2 (25.2)2.0L Duratec-HE Stage IV(145 PS)
1847.9 (35.8)6 (47.1)11.2 (25.2)2.0L Duratec-HE Stage V(145 PS)
2239.3 (30.4)6.7 (42.2)13.8 (20.5)2.3L Duratec-HE (161 PS)
2229.3 (30.4)6.8 (41.5)13.6 (20.8)2.5L Duratec-ST (220 PS)
1495.6 (50.4)4.6 (61.4)7.3 (38.7)1.8L Duratorq-TDCi (100 PS)
1395.3 (53.3)4.4 (64.2)6.8 (41.5)1.8L Duratorq-TDCi (125 PS)ECONETIC
1545.8 (48.7)4.8 (58.9)7.5 (37.7)1.8L Duratorq-TDCi (125 PS)
1565.9 (47.9)4.9 (57.6)7.6 (37.2)2.0L Duratorq-TDCi, 6-speed manual transmission
1395.2 (54.3)4.4 (64.2)6.6 (42.8)2.0L Duratorq-TDCi (115PS), 6-speed manual trans-mission ECONETIC
1877.1 (39.8)5.5 (51.4)9.7 (29.1)2.0L Duratorq-TDCi (136PS), 6-speed automatictransmission
1656.2 (45.6)4.9 (57.6)8.4(33.6)2.2L Duratorq-TDCi (175PS), 6-speed manual trans-mission
136
Fuel and refuelling
Estate
Fuel consumption figures
CO2emis-sionsCombinedExtra-urbanUrban
Variant
g/kml/100 km(mpg)
l/100 km(mpg)
l/100 km(mpg)
1707.2 (39.2)5.6 (50.4)10 (28.2)1.6L Duratec-Ti-VCT
1897.9 (35.8)6 (47.1)11.2 (25.2)2.0L Duratec-HE Stage IV(145 PS)
1847.9 (35.8)6 (47.1)11.2 (25.2)2.0L Duratec-HE Stage V(145 PS)
2239.3 (30.4)6.7 (42.2)13.8 (20.5)2.3L Duratec-HE (161 PS),6-speed automatic trans-mission
2229.3 (30.4)6.8 (41.5)13.6 (20.8)2.5L Duratec-ST (220 PS)
1515.7 (49.6)4.7 (60.1)7.4 (38.2)1.8L Duratorq-TDCi
1425.4 (47.9)4.5 (57.6)6.9 (40.9)1.8L Duratorq-TDCi (125 PS)ECONETIC
1565.9 (52.3)4.9 (62.8)7.6 (37.2)1.8L Duratorq-TDCi (125 PS)
1565.9 (47.9)4.9 (57.6)7.6 (37.2)2.0L Duratorq-TDCi
1395.2 (54.3)4.4 (64.2)6.6 (42.8)2.0L Duratorq-TDCi (115PS), 6-speed manual trans-mission ECONETIC
1877.1 (39.8)5.5 (51.4)9.7 (29.1)2.0L Duratorq-TDCi (136PS), 6-speed automatictransmission
1656.2 (45.6)4.9 (57.6)8.4(33.6)2.2L Duratorq-TDCi, 6-speed manual transmission
137
Fuel and refuelling
MANUAL TRANSMISSION
All vehicles
CAUTIONSDo not engage reverse gear whenthe vehicle is moving. This can causedamage to the transmission.
Do not apply any undue lateral forceto the gear lever when changing from5th to 4th gear. This could lead to the
inadvertent selection of 2nd gear and cancause damage to the transmission.
Selecting reverse gear
On some vehicles it is necessary to raisethe collar whilst selecting reverse gear.
E99067
AUTOMATICTRANSMISSION
Selector lever positions
E80836
S
ParkP
ReverseR
NeutralN
DriveD
Sport mode and manual shiftingS
WARNING
Apply the brakes before moving theselector lever and keep themapplied until you are ready to move
off.
Note: A cold engine has a higher idlespeed. This will increase the tendency foryour vehicle to creep when you haveselected a drive gear.
Press the button on the selector lever toselect reverse and park.
The selector lever position will be shownin the information display.
138
Transmission
Park
WARNINGSSelect park only when your vehicleis stationary.
Apply the parking brake andselect park before leavingyour vehicle. Make sure that the
selector lever is latched in position.
Note:An audible warning will sound if youopen the driver's door and you have notselected park.
In this position, power is not transmittedto the drive wheels and the transmissionis locked. You can start the engine withthe selector lever in this position.
Reverse
WARNING
Select reverse only when yourvehicle is stationary and the engineis at idle speed.
Neutral
In this position, power is not transmittedto the drive wheels but the transmissionis not locked. You can start the enginewith the selector lever in this position.
Drive
Select drive to shift automatically throughthe forward gears.
Sportmode andmanual shifting
2
1
E80837
S
S
Note: A shift will occur only when thevehicle speed and the engine speed areappropriate.
Note:When you select positionS, a gearchange may occur depending on theaccelerator pedal position in relation toactual vehicle speed.
Activate sport mode by moving theselector lever to position S. Sport modewill remain active until you shift manuallyup or down the gears.
Select manual shifting to shift manuallythrough the forward gears. Push theselector lever forwards to shift down andpull it backwards to shift up.
Drivemodes
The transmission will select theappropriate gear for optimumperformance based on ambienttemperature, road gradient, vehicle loadand driver input.
Hints on drivingwith anautomatic transmission
Moving off
1. Release the parking brake.
139
Transmission
2. Release the brake pedal and pressthe accelerator pedal.
Stopping
1. Release the accelerator pedal andpress the brake pedal.
2. Apply the parking brake.
Kickdown
Press the accelerator pedal fully with theselector lever in the drive position to selectthe next lowest gear for optimumperformance. Release the acceleratorpedal when you no longer requirekickdown.
Emergency park positionrelease lever
Use the lever to move the selector leverfrom the park position in the event of anelectrical malfunction or if your vehicle hasa flat battery.
E87934
1. Remove the centre console sidepanel.
E87935
Note: The lever is yellow.
1. Insert a flat-bladed screwdriver intothe slot and turn the screwdriverclockwise 90 degrees.
140
Transmission
PRINCIPLEOFOPERATION
Disc brakes
Wet brake discs result in reduced brakingefficiency. Dab the brake pedal whendriving from a car wash to remove the filmof water.
ABS
WARNING
The ABS does not relieve you ofyour responsibility to drive with duecare and attention.
The ABS helps you to maintain full steeringand directional stability when you brakeheavily in an emergency, by preventingthe road wheels from locking.
HINTSONDRIVINGWITHABS
When the ABS is operating, the brakepedal will pulse. This is normal. Maintainpressure on the brake pedal.
The ABS will not eliminate the dangersinherent when:• you drive too close to the vehicle in
front of you.• the vehicle is aquaplaning.
• you take corners too fast.
• the road surface is poor.
PARKINGBRAKE
Applying the parking brake
E66567
WARNING
Make sure that the parking brake isapplied before you release the lever.
Note: Do not press the release buttonwhen you apply the parking brake.
1. Press the brake pedal firmly.2. Pull the parking brake lever upwards
to its fullest extent.
Parking on a hill
If you have to park facing uphill, select firstgear and turn the front wheels away fromthe kerb. If you have to park facingdownhill, select reverse gear and turn thefront wheels towards the kerb.
Releasing the parking brake
1. Press the brake pedal firmly.2. Pull the parking brake lever upwards
slightly, press the release button andpush the lever downwards.
141
Brakes
PRINCIPLEOFOPERATION
Electronicstabilityprogramme(ESP)
WARNING
ESP does not relieve you of yourresponsibility to drive with due careand attention.
E72903
A A
AB
B
B
B
without ESPA
with ESPB
The ESP supports stability when thevehicle starts to slide away from yourintended path. This is performed bybraking individual wheels and reducingengine torque as needed.
The system also provides an enhancedtraction control function by reducingengine torque if the wheels spin when youaccelerate. This improves your ability topull away on slippery roads or loosesurfaces, and improves comfort by limitingwheel spin in hairpin bends.
Stabilitycontrol(ESP)warninglamp
The ESP warning lamp will flash when thesystem is operating. See Warninglamps and indicators (page 76).
Emergency brake assist
WARNING
Emergency brake assist does notrelieve you of your responsibility todrive with due care and attention.
Emergency brake assist will detect whenyou brake heavily by measuring the rateat which you press the brake pedal. It willprovide maximum braking efficiency aslong as you press the pedal. Emergencybrake assist can reduce stoppingdistances in critical situations.
USINGSTABILITYCONTROL
Press and hold the switch for one second.The switch will illuminate. A message willbe shown in the display. SeeInformationmessages (page 92).
Press the switch again to turn the systemon. The system will be switched onautomatically every time you switch theignition on.
142
Stability control
PRINCIPLEOFOPERATION
The system makes it easier to pull awaywhen the vehicle is on a slope without theneed to use the parking brake.
When the system is active, the vehicle willremain stationary on the slope for two tothree seconds after you release the brakepedal. During this time, you have time tomove your foot from the brake to theaccelerator pedal and pull away. Thebrakes are released automatically oncethe engine has developed sufficient driveto prevent the vehicle from rolling downthe slope. This is an advantage whenpulling away on a slope, for example froma car park ramp, traffic lights or whenreversing uphill into a parking space.
WARNING
The system does not replace theparking brake. When you leave thevehicle, always apply the parking
brake and select first or reverse gear.
USINGHILL STARTASSIST
The system can operate in eitherautomatic or manual mode. If you selectautomatic mode, the system is activatedautomatically when the vehicle is on aslope and you press the brake pedal. Ifyou select manual mode, you mustactivate the system using the brake pedal.
To set the system mode:
E70499
E74629
AutoOff
Hill Launch
Manual
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downbuttons and press the right arrowbutton.
3. Highlight Hill Launch and press theright arrow button.
4. Highlight the desired setting and pressthe OK button to confirm the setting.If Off is selected, the system isswitched off and cannot be activatedeither automatically or manually.
5. Press the left arrow button to exit themenu. To return to the trip computerdisplay directly, hold the left arrowbutton pressed.
143
Hill start assist
Note: When the system is in manualactivation mode, only use the systemwhen pulling away uphill on gradientsgreater than 3%. If the vehicle is on theflat or on a downhill slope, an activesystem will make it difficult to pull awaysmoothly.
Activating the system
WARNINGSYou must remain in the vehicle onceyou have activated the system. Anyattempt to leave the vehicle will
deactivate the system automatically.
The system is active only if themessage Hill LaunchAssistactive is displayed in the
information display. During all times youare responsible for controlling the vehicle,supervising the system and intervening,if required.
You can activate the system only if thefollowing conditions have been met:
• The engine is running.
• The system is switched on (automaticor manual mode).
• The parking brake is fully disengaged.
• On vehicles with manual transmission,the clutch pedal is pressed.
• On vehicles with automatictransmission, the driver door is closed.
• No failure mode is present.
To activate the system in automaticmode:
1. Press the brake pedal to bring thevehicle to a complete standstill. Keepthe brake pedal depressed.
2. If the sensors detect that the vehicleis on a slope and the right drivingdirection is selected (first gear if thevehicle is pointing uphill, reverse gearif the vehicle is pointing downhill), thesystem will be activated automatically.Hill LaunchAssist active willappear in the display.
3. When you remove your foot from thebrake pedal, the vehicle will remain onthe slope without rolling away forapproximately two to three seconds.
4. Pull away using the accelerator andclutch pedal. The brakes will bereleased automatically.
To activate the system in manual mode:
1. Press the brake pedal to bring thevehicle to a complete standstill. Keepthe brake pedal depressed.
2. Quickly jab the brake pedal further untilHill LaunchAssistactive appearsin the display. The system is nowactive.
3. When you remove your foot from thebrake pedal, the vehicle will remain onthe slope without rolling away forapproximately two to three seconds.
4. Pull away using the accelerator andclutch pedal. The brakes will bereleased automatically.
144
Hill start assist
WARNING
When the system is active and thesystem detects a failure, the systemis deactivated and the message
Please use park brake! followed byHill LaunchA .not available will bedisplayed. The vehicle is still safe to bedriven and can be repaired during thenext service. The message Hill LaunchA. not available will also be displayedwith manual activation during a failure orif one of the activation criteria is not met.If you have switched the system off, nomessages will be displayed.
Deactivating the system
To deactivate the system, perform oneof the following:
• Apply the parking brake.
• Wait for two to three seconds until thesystem deactivates automatically.
• If a forward gear was selected whenthe system became active, selectreverse gear.
• If reverse gear was selected when thesystem became active, select aforward gear.
HillLaunchAssistoffwill appear in theinstrument cluster display.
145
Hill start assist
PRINCIPLEOFOPERATION
The active suspension provides improvedhandling, comfort and stability bycontinuously adjusting the damperproperties to the current road and drivingconditions. This system in conjunction withthe ABS system offers the benefit ofpotentially shorter stopping distances onrough road surfaces.
Depending on your preferences anddriving style, you can choose betweenthree different settings:
Comfort
This provides a softer driving feel.
Normal
Normal setting.
Sport
This provides a harder, sportier ride.
USINGACTIVESUSPENSION
Selecting a setting
Note:After you select a setting, you maynot immediately notice a difference in thevehicle's handling. The effect of thecontinuously controlled damping dependson the road surface and drivingconditions.
E70475
You can change the setting while driving.
Systemmalfunction
The active suspension system will switchoff automatically if it malfunctions. Thesuspension will be set to a fail-safecondition that will enable you to continuedriving but you will not be able to changethe suspension setting. Have this checkedas soon as possible.
146
Active suspension
PRINCIPLEOFOPERATION
WARNING
The parking aid does not relieve youof your responsibility to drive withdue care and attention.
CAUTIONSVehicles fitted with a trailer towmodule not approved by us may notcorrectly detect obstacles.
The sensors may not detect objectsin heavy rain or other conditions thatcause disruptive reflections.
The sensors may not detect objectswith surfaces that absorb ultrasonicwaves.
The parking aid does not detectobstacles moving away from thevehicle. They will only be detected
shortly after they start to move towardsthe vehicle again.
Take particular care when reversingwith a tow ball arm or rear fittedaccessories e.g. a bicycle carrier, as
the rear parking aid will only indicate thedistance from the bumper to the obstacle.
If you use a high pressure spray towash your vehicle, only spray thesensors briefly from a distance not
less than 20 centimetres (8 inches).
Note: On vehicles fitted with a tow ballarm, the parking aid is deactivatedautomatically when any trailer lamps (orlighting boards) are connected to the13-pin socket via a trailer tow module wehave approved.
Note: Keep the sensors free from dirt,ice and snow. Do not clean with sharpobjects.
Note: The parking aid may emit falsetones if it detects a signal using the samefrequency as the sensors or if the vehicleis fully laden.
Note: The outer sensors may detect theside walls of a garage. If the distancebetween the outer sensor and the sidewall remains constant for three seconds,the tone will switch off. As you continue,the inner sensors will detect rearwardobjects.
USINGTHEPARKINGAID
Switching the parking aid onand off
Note: The parking aid switches offautomatically when you start the engineor when you exceed 16 km/h (10 mph).
Note: The front and rear sensors arealways activated or deactivated together.
The parking aid is per default off. Toswitch the parking aid on, press the switchin the instrument panel or select reversegear.
The light in the switch illuminates whenthe parking aid is activated.
To turn it off, press the switch again.
Manoeuvringwith the parkingaid
E72902
147
Parking aid
Note: If a high pitch warning tone soundsfor three seconds and the light in theswitch is flashing, it indicates amalfunction. The system will be disabled.Have the system checked by properlytrained technicians.
You will hear an intermittent tone at adistance of up to approximately 150centimetres (59 inches) between theobstacle and rear bumper, 80 centimetres(31 inches) between the obstacle andfront bumper and 50 centimetres (20inches) to the side. Decreasing thedistance accelerates the intermittent tone.A continuous tone will start at a distanceof less than 30 centimetres (12 inches).
You will hear an alternating tone from thefront and rear if obstacles are closer than30 centimetres (12 inches) to the frontand rear bumpers.
148
Parking aid
PRINCIPLEOFOPERATION
Cruise control allows you to control yourspeed using the switches on the steeringwheel. You can use cruise control whenyou exceed 30 km/h (20 mph).
USINGCRUISECONTROL
WARNING
Do not use cruise control in heavytraffic, on twisty roads or when theroad surface is slippery.
Switching cruise control on
E70612
Setting a speed
E70615
Press the SET+ switch or the SET-switch to store and maintain your currentspeed. The cruise control indicatorilluminates.
Changing the set speed
WARNING
When you are going downhill, yourspeed may increase above the setspeed. The system will not apply the
brakes. Change down a gear and pressthe RES switch to assist the system inmaintaining the set speed.
Note: If you accelerate by pressing theaccelerator pedal, the set speed will notchange. When you release theaccelerator pedal, you will return to thespeed that you previously set.
Press the SET+ switch or the SET-switch to accelerate or decelerate.
Cancelling the set speed
E70614
Press the brake pedal or theCAN switch.The system will no longer control yourspeed. The cruise control indicator will gooff but the system will retain the speedthat you previously set.
149
Cruise control
Resuming the set speed
E70616
Press theRES switch. The cruise controlindicator illuminates and the system willattempt to resume the speed that youpreviously set.
Switching cruise control off
E70613
Press theOFF switch. The system will notretain the speed that you previously set.The cruise control indicator will go off.
150
Cruise control
PRINCIPLEOFOPERATION
The adaptive cruise control system isdesigned to help you maintain a gap fromthe vehicle ahead or a set road speed ifthere is no slower vehicle ahead. Thesystem is intended to provide enhancedoperation of the vehicle when followingother vehicles which are in the same laneand travelling in the same direction.
WARNINGSAdaptive cruise control is not acollision warning or avoidancesystem. The separate forward alert
function provides a collision warning andmitigation feature. See Forward alertfunction (page 155). You must interveneif the system does not detect a vehicle infront.
Adaptive cruise control cannotcover all traffic, weather and roadconditions.
When driving you are responsiblefor maintaining the correct distanceand speed, even when adaptive
cruise control is used. You must alwayspay attention to the traffic conditions andintervene when adaptive cruise control isnot maintaining a suitable speed orsuitable distance.
The adaptive cruise control doesnot brake for slow or stationaryvehicles.
When ACC is activated, you mayhear some unusual sounds duringautomatic braking. This is normal
and caused by the automatic brakingsystem.
The adaptive cruise control system isbased on the use of a radar sensor whichprojects a beam directly forward of thevehicle. This beam will detect any vehicleahead within the system's range.
The radar sensor is mounted behind thefront grille, immediately to the right of theFord badge (when viewed from the frontof the vehicle).
When using ACC, follow the strictguidelines below:
• Only use adaptive cruise control whenconditions are favourable, for exampleon motorways and main roads withsteady free flowing traffic.
• Do not use in poor visibility, specificallyfog, heavy rain, spray or snow.
• Do not use on icy or slippery roads.
• It is your responsibility to stay alert,drive safely and be in control of thevehicle at all times.
• Keep the front of the vehicle free fromdirt, metal badges or objects, includingvehicle front protectors and additionallights which may prevent the sensorfrom operating.
• Do not use ACC when entering orleaving a motorway.
The radar sensor has a limited field ofvision. In some situations it may detect avehicle other than the one expected ornot detect any vehicle at all.
151
Adaptive cruise control (ACC)
Detection beam issues
E71621
Detection issues can occur:
• When driving on a different line to thevehicle in front (A).
• With vehicles that edge into your lanethat can only be detected once theyhave moved fully into your lane (B).Motorcycles may be detected late, ornot at all.
• There may be issues with thedetection of vehicles in front whengoing into and coming out of a bend(C). The detection beam will not followsharp curves in the road.
WARNING
In these cases ACC may brake lateor unexpectedly. The driver shouldstay alert and intervene if necessary.
Automatic brakingwith ACC
Adaptive cruise control will automaticallybrake for you, if required to maintain theset gap between your vehicle and the onedetected in front. This braking capacity islimited to approximately 30% of the totalmanual braking capacity to ensuresmooth and comfortable cruising. If thecar needs to brake more heavily than this,and you do not intervene by brakingmanually, an alarm will sound and awarning symbol will be displayed in thecluster.
WARNING
You must take immediate actiononce alerted, as the ACC brakingwill not be sufficient to keep a safe
distance to the vehicle in front.
USINGACC
The system is operated by adjustmentcontrols mounted on the steering wheel.The system is deactivated when thebrakes or clutch are used, the gearselector is moved to a neutral position orif the accelerator pedal is depressed fora longer period. The system will changeto standby mode, allowing you full manualcontrol of the vehicle.
Note: If the accelerator is depressed fora short period, for example whenovertaking, the system is temporarilydeactivated and then reactivated whenthe accelerator pedal is released. ACCoverride is displayed in the informationdisplay.
152
Adaptive cruise control (ACC)
A
C
E
D
B
E82310
ACC on/offA
ACC cancelB
Forward alert on/offC
ACC gap increaseD
ACC gap decreaseE
Switching ACCon
Press switch A. The system is set tostandby mode andStandby is displayedin the information display.
Setting a speed
E70615
Note: The system must be in Standbymode.
Press the SET+ switch or the SET-switch to select your desired cruisespeed. The speed is displayed in theinformation display and stored as the setspeed. The ACC indicator illuminates.
Note: Vehicle speed may be increasedand decreased at intervals of 5 km/h or5 mph. Smaller increases of 1 km/h or 1mph may be set by pressing the RESswitch.
Changing the set speed
Press the SET+ switch or the SET-switch to accelerate or decelerate.
Note: If the system does not react tothese changes the reason may be thatthe gap interval to the vehicle in frontprevents an increase in speed.
Setting the vehicle gap
E82311
The distance between you and the vehicledetected in front is maintained by avariable setting. There are five steps whichare represented by horizontal barsdisplayed in the information display. Onebar denotes the smallest gap and fivebars indicate the largest gap. These barsare shown empty when in standby modeand filled when in active mode.
153
Adaptive cruise control (ACC)
If no vehicle is detected in front, then onlyyour vehicle is displayed in the informationdisplay below the bars. The system willmaintain the set speed when conditionspermit. The set gap is maintained anddisplayed.
If a vehicle is detected by the sensor, thedisplay will show another vehicle abovethe horizontal bars:
E82312
This is a follow mode, and the system willaccelerate or decelerate as necessary tomaintain the set gap.
Press switch E to decrease the gap orswitch D to increase the gap. The gapselected will be represented by thenumber of bars in the display. Therecommended gap setting is three to fivebars.
Note: The gap setting is time dependantand therefore the distance willautomatically adjust with your speed. Forexample on a gap setting of three bars,the time gap is 1.8 seconds. This will meanthat at a speed of 100 km/h (62 mph), thedistance to the vehicle in front will bemaintained at 50 metres (164 feet)
CAUTION
Use the appropriate gap setting inaccordance with local trafficregulations.
Cancelling ACC
Press either the brake or clutch pedal, orswitch B. The system will return tostandby mode but will retain the setspeed and gap in the memory. TheACCindicator will go off.
ResumingACC
Press theRES switch. TheACC indicatorilluminates and the system will resumewith the previously set speed and vehiclegap setting if conditions permit.
Switching ACCoff
Press switch A.
Note: Pressing switchA does not returnthe system to standby mode. The storedspeed is not retained.
Note: To temporarily deactivate thesystem press switch B.
Automatic deactivation
The system is dependent on various othersafety systems, for example ABS andESP. If any of these systems aremalfunctioning or reacting to anemergency, the system is automaticallydeactivated.
In the event of automatic deactivation asignal will sound and the message ACCcancel is displayed in the informationdisplay. You must then intervene andadapt your driving and speed to vehiclesin front.
An automatic deactivation can be due tothe:
154
Adaptive cruise control (ACC)
• vehicle speed falling below 30 km/h(20 mph)
• wheels lose traction
• brake temperature is high, forexample when driving on mountainousor hilly roads
• engine speed is too low
• radar sensor is covered
• parking brake or electric parking brake(EPB) is applied.
If the engine speed drops too low, amessage is displayed in the informationdisplay instructing you to change down agear (manual transmission only). If you donot follow this recommendation then thesystem will go into automatic deactivationmode.
Note: The system will not operate if theelectronic stability programme (ESP) hasbeen manually switched off.
FORWARDALERTFUNCTION
The system assists you by warning of therisk of a collision, and reducing the severityof a collision with a vehicle in front. Thisworks by using two methods:
• You are alerted to a potential collisionso you may brake earlier than normal.
• Brake support is activated to enablefull braking effectiveness.
The collision alerts will only occur if thesystem is switched on, however the brakesupport is always on and cannot beturned off. Warnings are both visual andaudible. Brake support is activatedautomatically if necessary to reduce thecollision speed. The brake support systemonly reduces the collision speed if youbrake immediately once alerted.
WARNINGSNever wait for a collision warning.When driving you are responsiblefor maintaining the correct distance
and speed, even when the system isused.
The system will only react tovehicles in front travelling in thesame direction and will not react to
slow or stationary vehicles.
Never drive in a manner to provokethe system. The system is designedto assist in emergencies only.
The system alerts you by warning chimesand a visual warning in the informationdisplay. When forward alert is activated ared flashing warning triangle is displayedin the information display.
Note: You can deactivate the warningchimes by using the buttons on thesteering wheel. SeeAudiblewarningsand indicators (page 78).
The system does not operate in all drivingsituations and traffic, weather and roadconditions.
The radar sensor detects vehicles in frontthat are driving in the same direction asyou. If the risk of collision still increasesafter the initial warning then brake supportis activated. Brake support prepares thebrake system for rapid braking and thebrakes are applied gently, which may benoticed as a slight jerk. If the brake pedalis depressed sufficiently quickly thenbraking is implemented with full brakefunction, even if the force on the pedal islight.
155
Adaptive cruise control (ACC)
CAUTION
Warnings may be triggered late, beabsent or triggered unnecessarily ifthe traffic situation means that the
radar sensor cannot accurately detect avehicle in front. The system uses thesame radar sensors as adaptive cruisecontrol (ACC) and therefore has the samelimitations. SeePrincipleofoperation(page 151).
Note: The system may be used with orwithout the ACC system being activated.
Switching forward alert on/off
E94165
The indicator will illuminate.
Adjusting thewarningsensitivity
You may adjust the system warningsensitivity using the buttons on thesteering wheel. See Generalinformation (page 79).
This controls how early the visual andaudible warning is activated.
156
Adaptive cruise control (ACC)
GENERAL INFORMATION
WARNINGSUse load securing straps to anapproved standard, e.g. DIN.
Make sure that you secure all looseitems properly.
Place luggage and other loads aslow and as far forward as possiblewithin the luggage or loadspace.
Do not drive with the tailgate or reardoor open. Exhaust fumes mayenter the vehicle.
Do not exceed the maximum frontand rear axle loads for your vehicle.SeeVehicle identification (page
222).
Heavy loads, when placed in thepassenger compartment, should beon folded rear seats as shown. See
Rear seats (page 118).
CAUTIONSDo not allow items to contact the rearwindows.
Do not use any abrasive materials toclean the interior of the rear windows.
Do not install stickers or labels to theinterior of the rear windows.
E97377
LUGGAGEANCHORPOINTS
Estate
E86912
157
Load carrying
4-door and5-door
E86913
SLIDINGLOADSPACEFLOOR
WARNING
Do not slide the loadspace floorrearwards when the vehicle isstanding on an incline of 15 degrees
or more and facing uphill.
CAUTION
The maximum permissible weight onthe sliding loadspace floor is 200kilogrammes (441 pounds).
The maximum permissible weight on theend of the sliding loadspace floor whenthe floor is in the fully extended position(slid outside the luggage compartment)is 120 kilogrammes (265 pounds).
E74810
Press the unlocking handle and pull theloadspace floor rearwards. It will stop andengage at a midway position.
E74811
To slide it out fully, press the unlockinghandle again and pull it out until it engagesin the end position.
To slide it forwards, press the unlockinghandle and push it forwards.
Note: You do not have to exert as muchpressure on the unlocking handle if youpush the loadspace floor forwards slightlywhen operating it.
158
Load carrying
Storage compartment
A storage compartment is located in thefloor at the rear of the luggagecompartment.
To gain access to the storagecompartment, lift up the sliding loadspacefloor as follows:
E74812
1
2
E74813
3
1. Press the unlocking handle and pullthe loadspace floor rearwards a shortway.
2. Lift up the rear of the floor (1).3. Push the floor forwards until it
engages at the front (2).4. Release the support leg from the clip
on the underside of the floor.5. Insert the end into the square retainer
in the left-hand rail (3).6. Lift the storage compartment cover
using the loop.
To return the loadspace floor to thenormal position:
1. Hold the floor with one hand andrelease the support leg with the otherhand.
2. Insert the support leg back into theclip.
159
Load carrying
3. Lower the floor.4. Press the unlocking handle and pull
the loadspace floor rearwards until itdrops into position on the rails.
REARUNDERFLOORSTORAGE
Vehicleswith a slidingloadspace floor
Raise the loadspace floor to gain accessto the storage compartment. SeeSliding loadspace floor (page 158).
Vehicleswithout a slidingloadspace floor
E87689
CARGONETS
Luggage retention net
Installing the net
E87052
1. Push the ends of the upper bartowards each other and insert theminto the retainers on the roof. Push thebar forwards into the narrow sectionof the retainers.
E87053
2. Attach the net to the luggage anchorpoints. See Luggage anchorpoints (page 157).
160
Load carrying
E87054
3. Tighten the belts.
Removing the net
E87135
1. Release the belts.
2. Remove the net from the luggageanchor points.
3. Remove the upper bars.
LUGGAGECOVERS
WARNING
Do not place objects on the luggagecover.
E72969
Pull out the cover and secure it in theretaining points.
Release it from the retaining points andlet it roll back into the case. Clip theretaining hook onto the case.
E72970
To remove or install the cover, push eitherend of the case inwards.
161
Load carrying
ROOFRACKSANDLOADCARRIERS
Roof rack
WARNINGSIf you use a roof rack, the fuelconsumption of your vehicle will behigher and you may experience
different driving characteristics.
Read and follow the manufacturer’sinstructions when you are fitting aroof rack.
CAUTION
Do not exceed the maximumpermissible roof load of 75kilogrammes (165 pounds) (including
the roof rack).
Check the security of the roof rack andtighten its fittings as follows:
• before starting
• after driving 50 kilometres (30 miles)
• at 1 000 kilometres (600 miles)intervals.
To minimise windnoise when the roof rackis not in use, cross rails should be movedrearwards and placed together. Toreduce fuel consumption, cross railsshould be removed when not in use.
DOGGUARD
CAUTION
Keep a distance of at least onecentimetre between the dog guardand the seats in front of it.
Installingbehindthefrontseats
E86848
1. Push the ends of the bar on the grilletowards each other and insert theminto the retainers on the roof. Push thebar forwards into the narrow sectionof the retainers.
E87782
2. Attach the dog guard to the loweranchor points. Do not tighten thescrews.
162
Load carrying
E87783
3. Attach the grille to the lower bar withthe handwheels. Do not tighten thehandwheels.
4. Tighten the screws at the loweranchor points.
5. Tighten the handwheels.
Installingbehindtherearseats
E86848
1. Push the ends of the bar on the grilletowards each other and insert theminto the retainers on the roof. Push thebar forwards into the narrow sectionof the retainers.
E104424
2. Remove two screws from both theluggage anchor points. SeeLuggageanchor points (page 157).
3. Attach the lower bar to the grille withthe handwheels. Do not tighten thehandwheels.
4. Attach the dog guard lower bar to theluggage anchor points, secure withthe new supplied screws.
5. Tighten the handwheels.
Remove in the reverse order.
163
Load carrying
LOADRETAININGFIXTURES
WARNING
Do not exceed the maximumpermissible load of 60 kilogrammes(132 pounds) on two load retaining
fixtures and 30 kilogrammes (66 pounds)on one.
Check the security of the load retainingfixtures and tighten its fittings as follows:
• before starting
• after driving 50 kilometres (30 miles)
• at 1 000 kilometres (600 miles)intervals.
Installing the load retainingfixtures
E75003
Installing the load bracket
WARNINGSInstall the load bracket with thelongest section towards the rear ofthe vehicle. If you install it the wrong
way round, it may not hold the box inplace in the event of an accident.
Do not exceed the maximumpermissible load of 20 kilogrammes(44 pounds).
1
23 3
E76378
1. Turn the box over.
2. Position the load bracket.
3. Secure the load bracket with fourscrews.
E76379
164
Load carrying
4. Slide the captured bolts onto the load retaining fixture.
E76380
5. Secure the load bracket with the twowing nuts.
6. Remove in the reverse order.
165
Load carrying
TOWINGATRAILER
WARNINGSDo not exceed 100 km/h (62 mph).
The rear tyre pressures must beincreased by 0.2 bar (3 psi) abovespecification. See Technical
specifications (page 219).
Do not exceed the maximum grosstrain weight stated on the vehicleidentification plate. See Vehicle
identification (page 222).
Note: Not all vehicles are suitable orapproved to have tow bars fitted. Checkwith your dealer first.
Place loads as low and central to theaxle(s) of the trailer as possible. If you aretowing with an unladen vehicle, the loadin the trailer should be placed toward thenose, within the maximum nose load, asthis gives the best stability.
Note: The maximum trailer nose weightcan be found in the original vehicledocuments (confirmation of conformity).Alternatively refer to your dealer.
The stability of the vehicle to trailercombination is very much dependant onthe quality of the trailer.
In high altitude regions above 1 000metres (3 281 feet), the stipulatedmaximum permitted gross train weightmust be reduced by 10% for everyadditional 1 000 metres (3 281 feet).
Steep gradients
WARNING
The overrun brake on a trailer is notcontrolled by ABS.
Change down a gear before you reach asteep downhill gradient.
DETACHABLE TOWBALL
WARNINGSWhen not in use, always transportthe tow ball arm securely fastenedin the luggage compartment.
Take special care when fitting thetow ball arm as the safety of thevehicle and the trailer depends on
this.
Do not use any tools for mountingor dismounting the tow ball arm. Donot modify the trailer coupling. Do
not disassemble or repair the tow ball arm.
E71328
A 13-pin trailer socket and the tow ball armseat are provided underneath the rearbumper. Turn the trailer socket downthrough 90 degrees until it engages in theend position.
166
Towing
Unlocking the towball armmechanism
E713292
1
3
1. Remove the protecting cap (1). Insertthe key and turn it clockwise to unlock(2).
2. Hold the tow ball arm. Pull thehandwheel out and turn it clockwiseuntil it clicks (3).
3. The red mark on the handwheel mustalign with the green mark on the towball.
4. Release the handwheel. The tow ballarm is unlocked.
Inserting the towball arm
1
2E71330
WARNING
The tow ball arm may only beinserted when completely unlocked.
1. Pull out the plug.2. Insert the tow ball arm vertically and
press it upwards until it engages (1).Do not hold your hand near thehandwheel.
3. The green mark on the handwheelmust align with the green mark on thetow ball.
4. To lock, turn the key anti-clockwiseand remove the key (2).
5. Pull the protecting cap from the keybow and press it onto the lock.
167
Towing
Drivingwith a trailer
E71331
A
B
WARNING
If any of the below conditionscannot be met, do not use the towbar and have it checked by a
properly trained technician.
Before starting your journey, make surethat the tow ball arm is properly locked.Check:
• the green marks are aligned.
• the handwheel (A) is correctly fittedto the tow ball arm.
• you have removed the key (B).
• the tow ball arm is securely positioned.It must not move when jerked.
Removing the towball arm
3
1E71332
2
1. Unhitch the trailer.2. Remove the protecting cap. Press the
cap into the key bow. Insert the keyand unlock (1).
3. Hold the tow ball arm. Pull thehandwheel out, turn it clockwiseagainst the stop (2) and remove thetow ball arm (3).
4. Release the handwheel.
When unlocked in this way, the tow ballarm can be reinserted at any time.
168
Towing
Drivingwithout a trailer
E94771
1
1. Remove the tow ball arm.2. Insert the plug into its seat (1).
WARNING
Never unlock the tow ball arm withthe trailer attached.
Maintenance
CAUTION
Remove the tow ball arm and protectthe seat with the plug before steamcleaning your vehicle.
Keep the system clean. Periodicallylubricate bearings, sliding surfaces, andlocking balls with resin-free grease or oiland the lock with graphite.
Keep a note of the key number. In caseof loss, replacement keys are availablefrom the manufacturer by stating the4-digit key number.
169
Towing
RUNNING-IN
Tyres
WARNING
New tyres need to be run-in forapproximately 500 kilometres (300miles). During this time, you may
experience different drivingcharacteristics.
Brakes and clutch
WARNING
Avoid heavy use of the brakes andclutch if possible for the first 150kilometres (100 miles) in town and
for the first 1 500 kilometres (1 000 miles)on motorways.
Engine
CAUTION
Avoid driving too fast during the first1 500 kilometres (1 000 miles). Varyyour speed frequently and change
up through the gears early. Do not labourthe engine.
GENERALDRIVINGPOINTS- VEHICLESWITH: SPORTSSUSPENSION
The distance between the underside ofyour vehicle and the ground is reducedcompared to other models. Drive withextreme care to avoid damage to yourvehicle.
COLDWEATHERPRECAUTIONS
The functional operation of somecomponents and systems can beaffected at temperatures below -30°C(-22°F).
DRIVINGTHROUGHWATER
Driving throughwater
CAUTIONSDrive through water in an emergencyonly, and not as part of normaldriving.
Engine damage can occur if waterenters the air filter.
In an emergency, the vehicle can bedriven through water to a maximum depthof 200 mm and at a maximum speed of10 km/h (6 mph). Extra caution should beexercised when driving through flowingwater.
When driving in water, maintain a lowspeed and do not stop the vehicle. Afterdriving through water, and as soon as itis safe to do so:• Depress the brake pedal lightly and
check that full brake function isachieved.
• Check that the horn works.
• Check that the vehicle's lights are fullyoperational.
• Check the power assistanceof the steering system.
170
Driving hints
FIRSTAIDKIT
Space is provided in the luggagecompartment.
4-door
E87654
5-door
E87655
Estate
E87656
WARNINGTRIANGLE
4-door and5-door
E87657
Space is provided in the luggagecompartment.
Estate and vehicleswith tyrerepair kit
Space is provided under the carpet.
See Rear under floor storage (page160).
171
Emergency equipment
INSPECTINGSAFETYSYSTEMCOMPONENTS
Seat belts
Belts subjected to strain, as a result of anaccident, should be renewed and theanchorages checked by a properlytrained technician.
172
Status after a collision
FUSEBOXLOCATIONS
Engine compartment fuse box
E72588
Central fuse box
E72589
1. Loosen the screws.
E72590
2. Turn the knob through 90 degreesand release the fuse box from theretaining bracket.
3. Lower the fuse box and pull it towardsyou.
E72622
4. Remove the cover to gain access tothe fuses (vehicles with a cooled glovebox).
5. Install in the reverse order.
173
Fuses
Rear fuse box - 4-door and5-door
1
E87481
1. Remove the cover.
2
E87482
2. Remove the relevant fuse box cover.
Rear fuse box - Estate
1
2
E87479
1. Release the catches.
2. Remove the cover.
3
3
3
E87480
3. Remove the relevant fuse box cover.
174
Fuses
CHANGINGAFUSE
WARNINGSDo not modify the electrical systemof your vehicle in any way. Haverepairs to the electrical system and
the replacement of relays and high currentfuses carried out by a properly trainedtechnician.
Switch the ignition and all electricalequipment off before touching orattempting to change a fuse.
CAUTION
Fit a replacement fuse with the samerating as the one you have removed.
Note: You can identify a blown fuse bya break in the filament.
Note: All fuses, except high currentfuses, are a push fit.
Note: A fuse puller is located in theengine compartment fuse box.
175
Fuses
FUSESPECIFICATIONCHART
Engine compartment fuse box
E75525
Circuits protectedColourAmpereratingFuse
Transmission control modulered10F1
Glow plug monitoring (diesel engines)tan5F2
176
Fuses
Circuits protectedColourAmpereratingFuse
Engine cooling fan - twin fan (2.3L Duratec-HE)brown701F3
Electric hydraulic power steering (EHPAS)(2.0L Duratorq-TDCi)clear801F3
Glow plugsyellow60F4
Engine cooling fanyellow60F5
HEGO sensors 1 (engine management),variable valve timing (engine management),CMS sensor, Oxygen sensor
red10F6
Relay coilstan5F7
Powertrain control modulered10F8
MAF Sensor, Swirl Control Valve , FuelInjectors, CCV PTC Heater, Variable IntakeValve, Variable Exhaust Valve (enginemanagement)
red10F9
Engine control modulered10F10
PCV Valve, VCV Valve, Water in Fuel Sensor,Sonic Purge Valve, Swirl Control Valve, Vari-able Intake Valve, EGR Valve, IVVT Oil ControlValve (engine management)
red10F11
EGR Throttle, Variable Turbo Control Valve,Coil on Plug; Canister Purge Valve, PowerSteering Pressure Switch (engine manage-ment)
red10F12
Air conditioning relayblue15F13
Diesel filter heaterblue15F14
Starter relayorange40F15
Diesel auxiliary heater (PTC)clear80F16
Central fuse box supply Ayellow60F17
Central fuse box supply Byellow60F18
Rear fuse box supply Cyellow60F19
Rear fuse box supply Dyellow60F20
177
Fuses
Circuits protectedColourAmpereratingFuse
Not used––F21
Windscreen wiper modulegreen30F22
Heated rear windowclear251F23
Headlamp washergreen30F24
ABS valvesgreen30F25
ABS pumporange40F26
Fuel fired heatergreen30F27
Heater blowerorange40F28
Not used––F29
Not used––F30
Hornblue15F31
Fuel fired heater - remote controltan5F32
Light switch module, engine compartmentfuse box coilstan5F33
Heated windscreen (left-hand side)orange40F34
Heated windscreen (right-hand side)orange40F35
ABStan5F36
Heated front washer jetsred10F37
Adaptive cruise control (ACC)tan5F38
Adaptive front lighting system (AFS)blue15F39
Not used––F40
Instrument panelyellow20F41
Engine control module, transmission controlmodule, electric hydraulic power steering(EHPAS) 15 feed
red10F42
Headlamp levelling, adaptive front lightingsystem (AFS)tan5F43
Not used--F44
178
Fuses
Circuits protectedColourAmpereratingFuse
Rear window wiperblue15F45
1Fit a replacement with the same rating as the one you have removed.
Central fuse box
E75527
Circuits protectedColourAmpereratingFuse
Rain sensortan5F1
SRS (airbag) supplyred10F2
Yaw rate sensor (ESP), accelerator pedalsupplybrown7.5F3
179
Fuses
Circuits protectedColourAmpereratingFuse
Electronic feed, electronic fusebrown7.5F4
Not used--F5
Audio system (including voice control)blue15F6
Steering wheel modulebrown7.5F7
Instrument clustertan5F8
Main beamblue15F9
Power sunroofyellow20F10
Reversing lampsbrown7.5F11
Not used––F12
Front fog lampblue15F13
Windscreen washersblue15F14
Adaptive cruise control (ACC)red10F15
Not used––F16
Interior lampsred10F17
Engine immobilisertan5F18
Cigar lighterblue15F19
Not used––F20
Remote frequency receiver, Interior motionsensortan5F21
Fuel pumpyellow20F22
Fuel pump (2.2L Duratorq)brown7.5F22
Not used––F23
Ignition switchtan5F24
Fuel filler flapred10F25
Battery backup sounder (alarm system),OBD II (board computer diagnostics)tan5F26
Steering column unit, climate control moduletan5F27
180
Fuses
Circuits protectedColourAmpereratingFuse
Brake lamp switchtan5F28
Rear fuse box
4-door and5-door
E87483
181
Fuses
Estate
E75526
Circuits protectedColourAmpereratingFuse
Door module (left-hand front) (window up/down, central locking, electric folding mirror,heated mirror)
clear25FA1
182
Fuses
Circuits protectedColourAmpereratingFuse
Door module (right-hand front) (window up/down, central locking, electric folding mirror,heated mirror)
clear25FA2
Door module (left-hand rear) (window up/down)clear25FA3
Door module (right-hand rear) (window up/down)clear25FA4
Rear locking (without rear door modules)red10FA5
Auxiliary power socketblue15FA6
Relay coilstan5FA7
Steering column lockyellow20FA8
Not used––FA9
Electric driver's seatgreen30FA10
Accessories, trailer moduleyellow20FA11
Not used––FA12
Parking aid moduletan5FB1
Suspension moduleblue15FB2
Heated driver's seatblue15FB3
Heated front passenger seatblue15FB4
Left-hand rear heated seatblue15FB5
Not used--FB6
Right-hand rear heated seatblue15FB7
Not used––FB8
Electric front passenger seatgreen30FB9
Anti-theft alarm hornred10FB10
Not used––FB11
Not used––FB12
Not used--FC1
183
Fuses
Circuits protectedColourAmpereratingFuse
Not used--FC2
Not used--FC3
Not used--FC4
CD changer, rear seat entertainment systembrown7.5FC5
Not used--FC6
Seat memory function moduletan5FC7
Keyless entryyellow20FC8
Not used––FC9
Not used––FC10
Not used––FC11
Not used––FC12
184
Fuses
TOWINGPOINTS
CAUTION
The screw-in towing eye has aleft-hand thread. Turn itanti-clockwise to install it.
The screw-in towing eye is located in thespare wheel well.
The towing eye must always be carriedin the vehicle.
Front towing eye
E87280
Rear towing eye
E87282
Insert your finger into the hole on theunderside of the cover and prise off thecover. Install the towing eye.
TOWINGTHEVEHICLEONFOURWHEELS
All vehicles
WARNINGSSwitch the ignition on when yourvehicle is being towed. The steeringlock will engage and the direction
indicators and brake lamps will not workif you do not.
The brake servo and the powersteering pump do not operateunless the engine is running. Press
the brake pedal harder and allow forincreased stopping distances and heaviersteering.
CAUTIONSToo much tension in the tow ropecould cause damage to your vehicleor the vehicle that is towing.
Do not use a rigid tow bar on thefront towing eye.
Drive off slowly and smoothly withoutjerking the vehicle that is towing.
Vehicleswith automatictransmission
CAUTIONSDo not tow your vehicle faster than50 km/h (30 mph) or further than 50kilometres (30 miles).
If a speed of 50 km/h (30 mph) anda distance of 50 kilometres (30 miles)is to be exceeded the drive wheels
must be lifted clear of the ground.
185
Vehicle recovery
CAUTIONSIn the event of a mechanical failureof the transmission the drive wheelsmust be lifted clear of the ground.
Do not tow your vehicle backwards.
Select neutral when your vehicle isbeing towed.
186
Vehicle recovery
GENERAL INFORMATION
Have your vehicle serviced regularly tohelp maintain its roadworthiness andresale value. There is a large network ofFord Authorised Repairers that are thereto help you with their professionalservicing expertise. We believe that theirspecially trained technicians are bestqualified to service your vehicle properlyand expertly. They are supported by awide range of highly specialised toolsdeveloped specifically for servicing yourvehicle.
In addition to regular servicing, werecommend that you carry out thefollowing additional checks.
WARNINGSSwitch the ignition off beforetouching or attempting adjustmentof any kind.
Do not touch the electronic ignitionsystem parts after you haveswitched the ignition on or when the
engine is running. The system operatesat high voltage.
Keep your hands and clothing clearof the engine cooling fan. Undercertain conditions, the fan may
continue to run for several minutes afteryou have switched the engine off.
CAUTION
When carrying out maintenancechecks, make sure that filler caps arefitted securely.
Daily checks
• Exterior lamps.
• Interior lamps.
• Warning lamps and indicators.
Checkwhen refuelling
• Engine oil level. See Engine oilcheck (page 197).
• Brake fluid level. See Brake andclutch fluid check (page 198).
• Washer fluid level. SeeWasherfluidcheck (page 199).
• Tyre pressures (when cold). SeeTechnical specifications (page219).
• Tyre condition. SeeTyrecare (page217).
Monthly checks
• Engine coolant level (engine cold).See Engine coolant check (page197).
• Pipes, hoses and reservoirs for leaks.
• Power steering fluid level. SeePowersteeringfluidcheck (page198).
• Air conditioning operation.
• Parking brake operation.
• Horn operation.
• Tightness of wheel nuts. SeeTechnical specifications (page219).
187
Maintenance
OPENINGANDCLOSINGTHEBONNET
Opening the bonnet
E73698
E105063
Raise the bonnet slightly and move thecatch upwards.
E87786
Open the bonnet and support it with thestrut.
Closing the bonnet
WARNING
Make sure that the bonnet is closedproperly.
Lower the bonnet and allow it to dropfrom under its own weight for the last20 – 30 centimetres (8 - 11 inches).
188
Maintenance
ENGINECOMPARTMENTOVERVIEW - 1.6LDURATEC-16VTI-VCT (SIGMA)
A C
GJ F
D EB
HIE87714
Brake and clutch fluid reservoir (right-hand drive). See Brake and clutchfluid check (page 198).
A
Engine oil filler cap1. See Engine oil check (page 197).B
Brake and clutch fluid reservoir (left-hand drive). See Brake and clutchfluid check (page 198).
C
Battery. See Vehicle battery (page 204).D
Engine compartment fuse box. See Fuses (page 173).E
Air cleaner. No maintenance necessary.F
Screen washer fluid reservoir. See Washer fluid check (page 199).G
Engine oil dipstick1. See Engine oil check (page 197).H
Power steering fluid reservoir. See Power steering fluid check (page198).
I
Engine coolant reservoir. See Engine coolant check (page 197).J1The filler caps and the engine oil dipstick are coloured for easy identification.
189
Maintenance
ENGINECOMPARTMENTOVERVIEW - 2.0LDURATEC-HE(MI4)
A C
GJ F
D EB
HIE73231
Brake and clutch fluid reservoir (right-hand drive). See Brake and clutchfluid check (page 198).
A
Engine oil filler cap1. See Engine oil check (page 197).B
Brake and clutch fluid reservoir (left-hand drive). See Brake and clutchfluid check (page 198).
C
Battery. See Using booster cables (page 204).D
Engine compartment fuse box. SeeFusespecificationchart (page 176).E
Air cleaner. No maintenance necessary.F
Screen washer fluid reservoir. See Washer fluid check (page 199).G
Engine oil dipstick1. See Engine oil check (page 197).H
Power steering fluid reservoir. See Power steering fluid check (page198).
I
Engine coolant reservoir. See Engine coolant check (page 197).J1The filler caps and the engine oil dipstick are coloured for easy identification.
190
Maintenance
ENGINECOMPARTMENTOVERVIEW - 2.3LDURATEC-HE(MI4)
E81313
A C
GJ F
D EB
HI
Brake and clutch fluid reservoir (right-hand drive). See Brake and clutchfluid check (page 198).
A
Engine oil filler cap1. See Engine oil check (page 197).B
Brake and clutch fluid reservoir (left-hand drive). See Brake and clutchfluid check (page 198).
C
Battery. See Using booster cables (page 204).D
Engine compartment fuse box. SeeFusespecificationchart (page 176).E
Air cleaner. No maintenance necessary.F
Screen washer fluid reservoir. See Washer fluid check (page 199).G
Engine oil dipstick1. See Engine oil check (page 197).H
Power steering fluid reservoir. See Power steering fluid check (page198).
I
Engine coolant reservoir. See Engine coolant check (page 197).J1The filler caps and the engine oil dipstick are coloured for easy identification.
191
Maintenance
ENGINECOMPARTMENTOVERVIEW -2.5LDURATEC (VI5)
A C
GJ I F
D EB
HE73232
Brake and clutch fluid reservoir (right-hand drive). See Brake and clutchfluid check (page 198).
A
Engine oil filler cap1. See Engine oil check (page 197).B
Brake and clutch fluid reservoir (left-hand drive). See Brake and clutchfluid check (page 198).
C
Battery. See Using booster cables (page 204).D
Engine compartment fuse box. SeeFusespecificationchart (page 176).E
Screen washer fluid reservoir. See Washer fluid check (page 199).F
Air cleaner. No maintenance necessary.G
Engine oil dipstick1. See Engine oil check (page 197).H
Power steering fluid reservoir. See Power steering fluid check (page198).
I
Engine coolant reservoir. See Engine coolant check (page 197).J1The filler caps and the engine oil dipstick are coloured for easy identification.
192
Maintenance
ENGINECOMPARTMENTOVERVIEW-1.8LDURATORQ-TDCI(LYNX) DIESEL
A C
GJ I F
D EB
HE73233
Brake and clutch fluid reservoir (right-hand drive). See Brake and clutchfluid check (page 198).
A
Engine oil filler cap1. See Engine oil check (page 197).B
Brake and clutch fluid reservoir (left-hand drive). See Brake and clutchfluid check (page 198).
C
Battery. See Using booster cables (page 204).D
Engine compartment fuse box. SeeFusespecificationchart (page 176).E
Air cleaner. No maintenance necessary.F
Screen washer fluid reservoir. See Washer fluid check (page 199).G
Engine oil dipstick1. See Engine oil check (page 197).H
Power steering fluid reservoir. See Power steering fluid check (page198).
I
Engine coolant reservoir. See Engine coolant check (page 197).J1The filler caps and the engine oil dipstick are coloured for easy identification.
193
Maintenance
ENGINECOMPARTMENTOVERVIEW - 2.0LDURATORQ-TDCI (DW)DIESEL
A C
GJ I F
D EB
HE73234
Brake and clutch fluid reservoir (right-hand drive). See Brake and clutchfluid check (page 198).
A
Engine oil filler cap1. See Engine oil check (page 197).B
Brake and clutch fluid reservoir (left-hand drive). See Brake and clutchfluid check (page 198).
C
Battery. See Using booster cables (page 204).D
Engine compartment fuse box. SeeFusespecificationchart (page 176).E
Air cleaner. No maintenance necessary.F
Screen washer fluid reservoir. See Washer fluid check (page 199).G
Engine oil dipstick1. See Engine oil check (page 197).H
Power steering fluid reservoir. See Power steering fluid check (page198).
I
Engine coolant reservoir. See Engine coolant check (page 197).J1The filler caps and the engine oil dipstick are coloured for easy identification.
194
Maintenance
ENGINECOMPARTMENTOVERVIEW - 2.2LDURATORQ-TDCI (DW)DIESEL
A C
GJ F
D EB
HIE87715
Brake and clutch fluid reservoir (right-hand drive): See Brake and clutchfluid check (page 198).
A
Engine oil filler cap1: See Engine oil check (page 197).B
Brake and clutch fluid reservoir (left-hand drive): See Brake and clutchfluid check (page 198).
C
Battery: See Vehicle battery (page 204).D
Engine compartment fuse box: See Fuses (page 173).E
Air cleaner: No maintenance necessary.F
Screen washer fluid reservoir: See Washer fluid check (page 199).G
Engine oil dipstick1: See Engine oil check (page 197).H
Power steering fluid reservoir: See Power steering fluid check (page198).
I
Engine coolant reservoir: See Engine coolant check (page 197).J1The filler caps and the engine oil dipstick are coloured for easy identification.
195
Maintenance
ENGINEOILDIPSTICK - 1.6LDURATEC-16V TI-VCT(SIGMA)
E95540
BA
MINA
MAXB
ENGINEOILDIPSTICK-2.0LDURATEC-HE (MI4)/2.3LDURATEC-HE (MI4)
E92036
A B
MINA
MAXB
ENGINEOILDIPSTICK-2.5LDURATEC (VI5)
E95542
BA
MINA
MAXB
ENGINEOILDIPSTICK - 1.8LDURATORQ-TDCI (LYNX)DIESEL
E95527
B
A
MINA
MAXB
196
Maintenance
ENGINEOILDIPSTICK-2.0LDURATORQ-TDCI (DW)DIESEL/2.2LDURATORQ-TDCI (DW)DIESEL
E95543
BA
MINA
MAXB
ENGINEOILCHECK
CAUTION
Do not use oil additives or otherengine treatments. Under certainconditions, they could damage the
engine.
Note: The oil consumption of newengines reaches its normal level afterapproximately 5 000 kilometres (3 000miles).
Checking the oil level
CAUTION
Make sure that the level is betweenthe MIN and the MAX marks.
Note:Check the level before starting theengine.
Note: Make sure that your vehicle is onlevel ground.
Note:Oil expands when it is hot. The levelmay therefore extend a few millimetresbeyond the MAX mark.
Remove the dipstick and wipe it with aclean, lint free cloth. Replace the dipstickand remove it again to check the oil level.
If the level is at the MIN mark, top upimmediately.
Topping up
WARNINGSOnly top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.
Do not remove the filler cap whenthe engine is running.
Remove the filler cap.
CAUTION
Do not top up further than the MAXmark.
Top up with fluid that meets the Fordspecification. See Technicalspecifications (page 199).
ENGINECOOLANTCHECK
Checking the coolant level
WARNING
Do not allow the fluid to touch yourskin or eyes. If this happens, rinsethe affected areas immediately with
plenty of water and contact your doctor.
CAUTION
Make sure that the level is betweenthe MIN and the MAX marks.
197
Maintenance
Note: Coolant expands when it is hot.The level may therefore extend beyondthe MAX mark.
If the level is at the MIN mark, top upimmediately.
Topping up
WARNINGSOnly top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.
Do not remove the filler cap whenthe engine is running.
Do not remove the filler cap whenthe engine is hot. Wait for the engineto cool down.
Unscrew the cap slowly. Any pressurewill escape slowly as you unscrew thecap.
CAUTIONSDo not spill coolant on any part of theengine.
Do not top up further than the MAXmark.
Top up with fluid that meets the Fordspecification. See Technicalspecifications (page 199).
BRAKEANDCLUTCHFLUIDCHECK
WARNINGSDo not allow the fluid to touch yourskin or eyes. If this happens, rinsethe affected areas immediately with
plenty of water and contact your doctor.
WARNINGSIf the level is at the MIN mark, havethe system checked by a properlytrained technician as soon as
possible.
Note: The brake and the clutch systemsare supplied from the same reservoir.
Top up with fluid that meets the Fordspecification. See Technicalspecifications (page 199).
POWERSTEERINGFLUIDCHECK
WARNING
Do not allow the fluid to touch yourskin or eyes. If this happens, rinsethe affected areas immediately with
plenty of water and contact your doctor.
CAUTION
Make sure that the level is betweenthe MIN and the MAX marks.
If the level is at the MIN mark, top upimmediately.
Topping up
Remove the filler cap.
CAUTION
Do not top up further than the MAXmark.
Top up with fluid that meets the Fordspecification. See Technicalspecifications (page 199).
198
Maintenance
WASHERFLUIDCHECK The front and rear washer systems aresupplied from the same reservoir.
TECHNICALSPECIFICATIONS
Vehicle fluids
SpecificationRecommended fluidItem
WSS-M2C913-CCastrol Engine Oil*Engine oil
WSS-M2C204-A2Ford or Motorcraft PowerSteering FluidPower steering fluid
WSS-M97B44-DMotorcraft SuperPlus Anti-freezeCoolant
ESD-M6C57-AFord or Motorcraft SuperDOT 4 Brake FluidBrake fluid
* Providing it meets the specification defined by WSS-M2C913-C, you can also useFord Engine Oil or an alternative engine oil.
Toppinguptheoil: If you are unable to find an oil that meets the specification definedby WSS-M2C913-C, you must use SAE5W-30 (preferred), SAE5W-40 (exceptvehicles with E85 fuel) or SAE 10W-40 that meets the specification defined by eitherACEAA5/B5 (preferred) orACEAA3/B3. Using these oils can result in longer enginecranking periods, reduced engine performance, reduced fuel economy and increasedemission levels.
Castrol engine oil recommended.
E115472
Capacities
Capacity in litres(gallons)ItemVariant
MAX markPower steering systemAll
3.8 (0.8)Windscreen and rearwindow washer systemAll
4.1 (0.9)Engine lubrication system -including the oil filter1.6L Duratec-16V Ti-VCT
199
Maintenance
Capacity in litres(gallons)ItemVariant
3.8 (0.8)Engine lubrication system -excluding the oil filter1.6L Duratec-16V Ti-VCT
6.0 (1.3)Engine cooling system1.6L Duratec-16V Ti-VCT
70 (15.4)Fuel tank1.6L Duratec-16V Ti-VCT
4.3 (1.0)Engine lubrication system -including the oil filter2.0L Duratec-HE
3.9 (0.9)Engine lubrication system -excluding the oil filter2.0L Duratec-HE
6.2 (1.4)Engine cooling system2.0L Duratec-HE
70 (15.4)Fuel tank2.0L Duratec-HE
4.3 (1.0)Engine lubrication system -including the oil filter2.3L Duratec-HE
3.9 (0.9)Engine lubrication system -excluding the oil filter2.3L Duratec-HE
6.9 (1.5)Engine cooling system2.3L Duratec-HE
70 (15.4)Fuel tank2.3L Duratec-HE
5.8 (1.3)Engine lubrication system -including the oil filter2.5L Duratec-ST
5.5 (1.2)Engine lubrication system -excluding the oil filter2.5L Duratec-ST
7.1 (1.6)Engine cooling system2.5L Duratec-ST
70 (15.4)Fuel tank2.5L Duratec-ST
5.6 (1.2)Engine lubrication system -including the oil filter1.8L Duratorq-TDCi
5.0 (1.1)Engine lubrication system -excluding the oil filter1.8L Duratorq-TDCi
7.9 (1.7)Engine cooling system1.8L Duratorq-TDCi
70 (15.4)Fuel tank1.8L Duratorq-TDCi
5.5 (1.2)Engine lubrication system -including the oil filter2.0L Duratorq-TDCi
200
Maintenance
Capacity in litres(gallons)ItemVariant
5.0 (1.1)Engine lubrication system -excluding the oil filter2.0L Duratorq-TDCi
8.1 (1.8)Engine cooling system2.0L Duratorq-TDCi
70 (15.4)Fuel tank2.0L Duratorq-TDCi
6.0 (1.3)Engine lubrication system -including the oil filter2.2L Duratorq-TDCi
5.4 (1.2)Engine lubrication system -excluding the oil filter2.2L Duratorq-TDCi
8.4 (1.9)Engine cooling system2.2L Duratorq-TDCi
70 (15.4)Fuel tank2.2L Duratorq-TDCi
201
Maintenance
CLEANINGTHEEXTERIOR
WARNING
If you use a car wash with a waxingcycle, make sure that you removethe wax from the windscreen.
CAUTIONSSome car wash installations usewater at high pressure. This coulddamage certain parts of your vehicle.
Remove the aerial before using anautomatic car wash.
Switch the heater blower off toprevent contamination of the freshair filter.
We recommend that you wash yourvehicle with a sponge and lukewarmwater containing a car shampoo.
Cleaning the headlamps
CAUTIONSDo not scrape the headlamp lensesor use abrasives, alcoholic solventsor chemical solvents to clean them.
Do not wipe the headlamps whenthey are dry.
Cleaning the rearwindow
CAUTION
Do not scrape the inside of the rearwindow or use abrasives or chemicalsolvents to clean it.
Use a clean, lint free cloth or a dampchamois leather to clean the inside of therear window.
Cleaning the chrome trim
CAUTION
Do not use abrasives or chemicalsolvents. Use soapy water.
Body paintwork preservation
CAUTIONSDo not polish your vehicle in strongsunshine.
Do not allow polish to touch plasticsurfaces. It could be difficult toremove.
Do not apply polish to the windscreenor rear window. This could cause thewipers to become noisy and they
may not clear the window properly.
We recommend that you wax thepaintwork once or twice a year.
CLEANINGTHE INTERIOR
Seat belts
WARNINGSDo not use abrasives, or chemicalsolvents to clean them.
Do not allow moisture to penetratethe seat belt retractor mechanism.
Clean the seat belts with interior cleaneror water applied with a soft sponge. Letthe seat belts dry naturally, away fromartificial heat.
202
Vehicle care
Instrument cluster screens,LCD screens, radio screens
WARNING
Do not use abrasives, alcoholicsolvents or chemical solvents toclean them.
REPAIRINGMINORPAINTDAMAGE
CAUTION
Remove apparently harmless lookingsubstances from the paintworkimmediately (e.g. bird droppings, tree
resins, insect remains, tar spots, road saltand industrial fall out).
You should repair paintwork damagecaused by stones from the road or minorscratches as soon as possible. A choiceof products is available from your FordDealer. Read and follow themanufacturer’s instructions.
203
Vehicle care
USINGBOOSTERCABLES
CAUTIONSConnect batteries with only the samenominal voltage.
Always use booster cables withinsulated clamps and adequate sizecable.
Do not disconnect the battery fromthe vehicle’s electrical system.
Toconnect thebooster cables
A
B
C D
E102925
Flat battery vehicleA
Booster battery vehicleB
Positive connection cableC
Negative connection cableD
1. Position the vehicles so that they donot touch one another.
2. Switch off the engine and anyelectrical equipment.
3. Connect the positive (+) terminal ofvehicleBwith the positive (+) terminalof vehicle A (cable C).
4. Connect the negative (-) terminal ofvehicleB to the ground connection ofvehicle A (cable D). See Batteryconnection points (page 205).
CAUTIONSDonotconnect to thenegative(–) terminal of the flat battery.
Make sure that the cables are clearof any moving parts.
To start the engine
1. Run the engine of vehicle B atmoderately high speed.
2. Start the engine of vehicle A.
3. Run both vehicles for a minimum ofthree minutes before disconnectingthe cables.
CAUTION
Do not switch on the headlampswhen disconnecting the cables. Thepeak voltage could blow the bulbs.
Disconnect the cables in the reverseorder.
204
Vehicle battery
BATTERYCONNECTIONPOINTS
E114494
CAUTION
Donotconnect to thenegative(–) terminal of the flat battery.
205
Vehicle battery
GENERAL INFORMATION
CAUTIONSUse only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will make
the National Type Approval invalid.
If you change the diameter of thetyres from that fitted at the factory,the speedometer may not display
the correct speed. Take the vehicle toyour dealer to have the enginemanagement system reprogrammed.
A decal with tyre pressure data is locatedin the driver’s door opening at the B-pillar.
Check and set the tyre pressure at theambient temperature in which you areintending to drive the vehicle and whenthe tyres are cold.
CHANGINGAROADWHEEL
Lockingwheel nuts
You can obtain a replacement lockingwheel nut key and replacement lockingwheel nuts from your dealer using thereference number certificate.
Vehicleswith a temporarysparewheel
WARNINGSIf the spare wheel differs from theother fitted wheels, these rules mustbe followed:
Do not exceed 80 km/h (50 mph).
Drive the shortest possibledistances.
Do not fit more than one sparewheel on your vehicle at any onetime.
WARNINGSDo not use snow chains on this typeof wheel.
Do not drive through an automaticcar wash.
Do not carry out any tyre repairs ona temporary spare wheel.
CAUTION
The ground clearance of your vehiclewill be reduced. Take care whenparking next to a curb.
Note: Your vehicle may exhibit someunusual driving characteristics.
Vehicle jack
WARNINGSThe vehicle jack supplied with yourvehicle should only be used whenchanging a wheel in emergency
situations.
Before using the vehicle jack, checkthat it is not damaged or deformedand that the thread is lubricated and
free from foreign matter.
Never place anything between thejack and the ground, or the jack andthe vehicle.
Note: Vehicles with a tyre repair kit or runflat tyres are not equipped with a vehiclejack or a wheel brace.
It is recommended to use a workshoptype hydraulic jack for changing betweensummer and winter tyres.
Note: Use a jack with a minimum liftingcapacity of 1.5 tonnes and a lifting platewith a minimum diameter of 80 millimetres(3.1 inches).
206
Wheels and tyres
Vehicleswithout tyre repair kit orrun flat tyres
A
B
C
E86843
JackA
Wheel braceB
Space for locking wheel nut keyC
Your vehicle jack and wheel brace arelocated in the spare wheel well.
Jacking and lifting points
CAUTION
Use only the specified jacking points.If you use other positions, you maydamage the body, steering,
suspension, engine, braking system orthe fuel lines.
E92658
A
B
207
Wheels and tyres
Emergency use onlyA
MaintenanceB
E93184
A
Indentations in the sills A show thelocation of the jacking points.
E92932
E93020
Vehicleswith side skirts
E95345
Removing a roadwheel
WARNINGSPark your vehicle in such a positionthat neither the traffic nor you arehindered or endangered.
Set up a warning triangle.
Make sure that the vehicle is on firm,level ground with the wheelspointing straight ahead.
Switch off the ignition and apply theparking brake.
If your vehicle has a manualtransmission, select first or reversegear. If it has an automatic
transmission, select park.
Have the passengers leave thevehicle.
Secure the diagonally oppositewheel with an appropriate block orwheel chock.
208
Wheels and tyres
WARNINGSMake sure that the arrows ondirectional tyres point in the directionof rotation when the vehicle is
moving forwards. If you have to fit a sparewheel with the arrows pointing in theopposite direction, have the tyre refittedin the correct direction by a properlytrained technician.
Do not work underneath the vehiclewhen it is supported only by a jack.
Make sure that the jack is vertical tothe jacking point and the base is flaton the ground.
CAUTION
Do not lay alloy wheels face down onthe ground, this will damage thepaint.
Note: The spare wheel is located underthe floor cover in the luggagecompartment.
1. Insert the flat end of the wheel bracebetween the rim and the hub coverand carefully remove the hub cap orcover.
E71948
2. Install the locking wheel nut key.
3. Fully extend the wheel brace.
4. Slacken the wheel nuts.
5. Jack up the vehicle until the tyre isclear of the ground.
6. Remove the wheel nuts and thewheel.
Installing a roadwheel
WARNINGSUse only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will make
the National Type Approval invalid. SeeTechnical specifications (page 219).
Do not fit run flat tyres on vehiclesthat were not originally fitted withthem. Please contact your dealer
for more details regarding compatibility.
CAUTION
Do not install alloy wheels usingwheel nuts designed for use withsteel wheels.
209
Wheels and tyres
Note: Make sure the wheel and hubcontact surfaces are free from foreignmatter.
Note: Make sure that the cones on thewheel nuts are against the wheel.
1. Install the wheel.
2. Install the wheel nuts finger tight.
E71948
3. Install the locking wheel nut key.
1
2
3 4
5
E75442
4. Partially tighten the wheel nuts in thesequence shown.
5. Lower the vehicle and remove thejack.
6. Fully tighten the wheel nuts in thesequence shown. See Technicalspecifications (page 219).
7. Install the hub cap or cover using theball of your hand.
WARNING
Have the wheel nuts checked fortightness and the tyre pressurechecked as soon as possible.
Note: If the spare wheel is different in sizeor construction to the road wheels, havethis replaced as soon as possible.
TYREREPAIRKIT
Your vehicle may not have a spare tyre.In this case it will have an emergency tyrerepair kit that can be used to repair oneflat tyre.
The tyre repair kit is located in the sparewheel well.
General information
WARNINGSDepending on the type and extentof tyre damage, some tyres canonly be partially sealed or not sealed
at all. Loss of tyre pressure can affectvehicle handling, leading to loss of vehiclecontrol.
Do not use the tyre repair kit if thetyre has already been damaged asa result of being driven under
inflated.
Do not try to seal damage otherthan that located within the visibletread of the tyre.
Do not try to seal damage to thetyre’s sidewall.
210
Wheels and tyres
The tyre repair kit seals most tyrepunctures [with a diameter of up to sixmillimetres (1/4 inch)] to temporarilyrestore mobility.
Observe the following rules when usingthe kit:
• Drivewith caution and avoidmaking sudden steering ordrivingmanoeuvres, especially ifthe vehicle is heavily loaded or you aretowing a trailer.
• The kit will provide you with anemergency temporary repair, enablingyou to continue your journey to thenext vehicle or tyre dealer, or to drivea maximum distance of200 kilometres (125 miles).
• Do not exceed a maximumspeedof 80 km/h (50mph).
• Keep the kit out of the reach ofchildren.
• Only use the kit when the ambienttemperature is between –30°C (-22°F)and +70°C (+158°F).
Using the tyre repair kit
WARNINGSCompressed air can act as anexplosive or propellant.
Never leave the tyre repair kitunattended while in use.
CAUTION
Do not keep the compressoroperating for more than 10 minutes.
Note: Use the tyre repair kit only for thevehicle with which it was supplied.
• Park your vehicle at the roadside sothat you do not obstruct the flow oftraffic and so that you are able to usethe kit without being in danger.
• Apply the parking brake, even if youhave parked on a level road, to makesure that the vehicle will not move.
• Do not attempt to remove foreignobjects like nails or screws penetratingthe tyre.
• Leave the engine running while the kitis in use, but not if the vehicle is in anenclosed or poorly ventilated area (forexample, inside a building). In thesecircumstances, switch thecompressor on with the engine turnedoff.
• Replace the sealant bottle with a newone before the expiry date (see topof bottle) is reached.
• Inform all other users of the vehiclethat the tyre has been temporarilysealed with the tyre repair kit andmake them aware of the specialdriving conditions to be observed.
Inflating the tyre
WARNINGSCheck the sidewall of the tyre priorto inflation. If there are any cracks,bumps or similar damage, do not
attempt to inflate the tyre.
Do not stand directly beside the tyrewhile the compressor is pumping.
Watch the sidewall of the tyre. If anycracks, bumps or similar damageappear, turn off the compressor and
let the air out by means of the pressurerelief valveB. Do not continue driving withthis tyre.
211
Wheels and tyres
WARNINGSThe sealant contains natural rubberlatex. Avoid contact with skin andclothing. If this happens, rinse the
affected areas immediately with plenty ofwater and contact your doctor.
If the tyre inflation pressure does notreach 1.8 bar (26 psi) within sevenminutes, the tyre may have suffered
excessive damage, making a temporaryrepair impossible. In this case, do notcontinue driving with this tyre.
CAUTION
Screwing the bottle onto the bottleholder will pierce the seal of thebottle. Do not unscrew the bottle
from the holder as the sealant will escape.
212
Wheels and tyres
E94973
B
J
I
F
E
C
KA
G
HD
Protective capA
Pressure relief valveB
HoseC
Orange capD
213
Wheels and tyres
Bottle holderE
Pressure gaugeF
Power plug with cableG
Compressor switchH
LabelI
Bottle lidJ
Sealant bottleK
1. Open the lid of the tyre repair kit.
2. Peel off the label I showing themaximum permissible speed of80 km/h (50 mph) from the casingand attach it to the instrument panelin the driver’s field of view. Make surethe label does not obscure anythingimportant.
3. Take the hose C and the power plugwith cable G out of the kit.
4. Unscrew the orange cap D and thebottle lid J.
5. Screw the sealant bottle K clockwiseinto the bottle holder E fully tight.
6. Remove the valve cap from thedamaged tyre.
7. Detach the protective capA from thehose C and screw the hose C firmlyonto the valve of the damaged tyre.
8. Make sure that the compressor switchH is in position 0.
9. Insert the power plug G into the cigarlighter socket or auxiliary powersocket. SeeCigar lighter (page 121).See Auxiliary power sockets(page 122).
10. Start the engine.
11. Move the compressor switch H toposition 1.
12. Inflate the tyre for no longer thanseven minutes to an inflationpressure of minimum 1.8 bar (26 psi)and a maximum of 3.5 bar (51 psi).Move the compressor switch H toposition0 and check the current tyrepressure with pressure gauge F.
13. Remove the power plugG from thecigar lighter socket or auxiliary powersocket.
14. Quickly unscrew the hose C fromthe tyre valve and replace theprotective cap A. Fasten the valvecap again.
15. Leave the sealant bottle K in thebottle holder E.
16. Make sure the kit, the bottle lid andthe orange cap are stored safely, butstill easily accessible in the vehicle.The kit will be required again whenyou check the tyre pressure.
17. Immediately drive approximatelythree kilometres (two miles) so thatthe sealant can seal the damagedarea.
Note: When pumping in the sealantthrough the tyre valve, the pressure mayrise up to 6 bar (87 psi) but will drop againafter about 30 seconds.
214
Wheels and tyres
WARNING
If you experience heavy vibrations,unsteady steering behaviour ornoises while driving, reduce your
speed and drive with caution to a placewhere it is safe for you to stop the vehicle.Recheck the tyre and its pressure. If thetyre pressure is less than 1.3 bar (19 psi)or if there are any cracks, bumps or similardamage visible, do not continue drivingwith this tyre.
Checking the tyre pressure
1. Stop the vehicle after drivingapproximately three kilometres(two miles). Check, and wherenecessary, adjust the pressure of thedamaged tyre.
2. Attach the kit and read the tyrepressure from the pressure gauge F.
3. If the pressure of the sealant-filled tyreis 1.3 bar (19 psi) or more, adjust it tothe specified pressure. SeeTechnical specifications (page219).
4. Follow the inflation procedure onceagain to top up the tyre.
5. Check the tyre pressure again fromthe pressure gauge F. If the tyrepressure is too high, deflate the tyreto the specified pressure using thepressure relief valve B.
6. Once you have inflated the tyre to itscorrect tyre pressure, move thecompressor switch H to position 0,remove the power plug G from thesocket, unscrew the hose C, fastenthe valve cap and replace theprotective cap A.
7. Leave the sealant bottleK in the bottleholder E and store the kit away safelyin its original location.
8. Drive to the nearest tyre specialist toget the damaged tyre replaced.Before the tyre is removed from therim, inform your tyre dealer that thetyre contains sealant. Renew the kitas soon as possible after it has beenused once.
Note: Remember that emergencyroadside tyre repair kits only providetemporary mobility. Regulationsconcerning tyre repair after usage of tyrerepair kit may differ from country tocountry. You should consult a tyrespecialist for advice.
WARNING
Before driving, make sure the tyreis adjusted to the recommendedinflation pressure. See Technical
specifications (page 219). Monitor thetyre pressure until the sealed tyre isreplaced.
Empty sealant bottles can be disposedof together with normal household waste.Return remains of sealant to your dealeror dispose of it in compliance with localwaste disposal regulations.
215
Wheels and tyres
RUNFLAT TYRES
Principle of operation
Standard tyre
BA
C
E75207
Wheel rim position with correcttyre pressure
A
Wheel rim position withinsufficient tyre pressure
B
TyreC
Run flat tyre
B
DC
A
E87667
Wheel rim position with correcttyre pressure
A
Wheel rim position withinsufficient tyre pressure
B
TyreC
Reinforced sidewallD
When a standard tyre experiences adrastic loss of inflation pressure, the rimof the wheel brings the full weight of thevehicle to bear on the collapsed sidewalls.You can barely manoeuvre the vehicleand the tyre is destroyed.
Run flat tyres have sturdy, reinforcedsidewalls that support the rim should thetyre suffer a loss of inflation pressure.
What to do if a run flat tyre hasa puncture
Due to the run-flat properties of thesetyres, you may not notice any tyre defect.Your vehicle is equipped with a tyrepressure monitoring system that alertsyou to any drop in tyre pressure. SeeTechnical specifications (page 219).
In the event of a tyre defect:
• immediately slow down to a maximumspeed of 80 km/h (50 mph)
• avoid sudden or erratic braking andsteering manoeuvres and beespecially careful negotiating bends
• do not drive more than 80 kilometres(50 miles) after the defect is detected
• have the defective tyre replaced assoon as possible.
Replacing run flat tyres
WARNINGSMake sure that the workshop isaware that your vehicle is equippedwith special run flat tyres.
Never repair or reuse run flat tyresthat are damaged or have beendriven on run flat.
If a run flat tyre has to be replaced, havethe respective wheel rim inspected forany damage.
216
Wheels and tyres
WARNINGSDo not fit a mixture of run flat andstandard tyres. In isolated cases, astandard tyre can be temporarily
mounted on a vehicle otherwise equippedwith run flat tyres. It must be pointed outto the driver that the standard tyre has norunflat properties.
Do not fit run flat tyres on vehiclesthat were not originally fitted withthem. Please contact your dealer
for more details regarding compatibility.
Run flat tyres may be sold and mountedonly by specially trained and certified tyredealers.
TYRECARE
E70415
To make sure the front and rear tyres ofyour vehicle wear evenly and last longer,we recommend that you swap the tyresfrom front to rear and vice versa at regularintervals of between 5 000 and 10 000km (3 000 and 6 000 miles).
CAUTION
Do not scrub the sidewalls of thetyres when you are parking.
If you have to mount a kerb, do so slowlyand approach it with the wheels atright-angles to the kerb.
Examine the tyres regularly for cuts,foreign objects and uneven wear of thetread. Uneven wear could mean that thewheel alignment is outside specification.
Check the tyre pressures (including thespare) when cold, every two weeks.
USINGWINTER TYRES
CAUTION
Make sure that you use the correctwheel nuts for the type of wheel thewinter tyres are fitted to.
If winter tyres are used, make sure thatthe tyre pressures are correct. SeeTechnical specifications (page 219).
USINGSNOWCHAINS
WARNINGSDo not exceed 50 km/h (30 mph).
Do not use snow chains onsnow-free roads.
Do not fit snow chains to 235/45 R17, 235/40 R 18 or T125/90 R 16tyres.
CAUTION
If your vehicle is fitted with wheeltrims, remove them before fittingsnow chains.
Note: The ABS will continue to operatenormally.
Only use small link snow chains.
Only use snow chains on the front wheels.
217
Wheels and tyres
TYREPRESSUREMONITORINGSYSTEM
WARNINGSThe system does not relieve you ofyour responsibility to regularly checkthe tyre pressures.
The system will only provide a lowtyre pressure warning. It will notinflate the tyres.
The system may take longer todetect low pressure in the tyres ifyou have fitted snow chains.
Do not drive on significantlyunder-inflated tyres. This may causethe tyres to overheat and fail.
Under-inflation reduces fuel efficiency,tyre tread life and may also affect yourability to drive the vehicle safely.
CAUTIONSDo not bend or damage the valveswhen you are inflating the tyres.
Have tyres installed by properlytrained technicians.
The system monitors the pressure in thetyres using sensors located on the wheelsand a receiver located in your vehicle.When the system detects low pressurein the tyres, a warning message isdisplayed in the information display. SeeInformationmessages (page 92).
If a low pressure warning message isdisplayed in the information display, checkthe tyre pressures as soon as possibleand inflate them to the recommendedpressure. See Technicalspecifications (page 219). If thishappens frequently, have the causedetermined and rectified as soon aspossible.
Checking the tyre pressures
Note: If the tyre pressures are greaterthan or equal to 3.3 bar (48 lbf/in²), youwill see the + symbol below the pressurevalue. The system only measurespressure up to 3.3 bar (48 lbf/in²). The +symbol indicates that the tyre pressuresmay be higher.
Note: Type 3 instrument clusters have aslightly different menu structure. SelectSettings first to access Information.
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. Highlight Information with the upand down buttons and press the rightarrow button.
3. Highlight Tyre Pressures with theup and down buttons and press theright arrow button.
4. Highlight the desired setting and pressthe OK button to confirm the setting.
5. Press the left arrow button to exit themenu. Hold the left arrow buttonpressed to return to the trip computerdisplay.
Setting the vehicle load
Note: Type 3 instrument clusters have aslightly different menu structure. SelectSettings first to access Setup.
Correct tyre pressure settings depend onvehicle load. See Technicalspecifications (page 219). The systemcan only detect low pressure if you haveentered the current vehicle load.
1. Press the right arrow button on thesteering wheel to enter the mainmenu.
2. HighlightSetupwith the up and downbuttons and press the right arrowbutton.
218
Wheels and tyres
3. Highlight Tyre Pressures with theup and down buttons and press theright arrow button.
4. Highlight the desired setting and pressthe OK button to confirm the setting.
5. Press the left arrow button to exit themenu. Hold the left arrow buttonpressed to return to the trip computerdisplay.
TECHNICALSPECIFICATIONS
Wheel nut torque
Nm (Ib-ft)Wheel type
140 (103)All
Tyre pressures (cold tyres)
Up to 80 km/h (50mph)
Tyre pressures
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
4.2 (61)4.2 (61)4.2 (61)4.2 (61)T125/90 R 16All
Up to 160 km/h (100mph)
Tyre pressures
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.5 (36)2.2 (32)2.2 (32)205/55 R 161.6L Duratec-Ti-VCT
2.8 (41)2.5 (36)2.2 (32)2.2 (32)215/55 R 162.0L Duratec-HE
2.8 (41)2.5 (36)2.2 (32)2.2 (32)235/45 R 172.0L Duratec-HE
219
Wheels and tyres
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.5 (36)2.2 (32)2.2 (32)235/40 R 182.0L Duratec-HE
2.8 (41)2.5 (36)2.2 (32)2.2 (32)215/55 R 162.3L Duratec-HE
2.8 (41)2.5 (36)2.2 (32)2.2 (32)235/45 R 172.3L Duratec-HE
2.8 (41)2.5 (36)2.2 (32)2.2 (32)235/40 R 182.3L Duratec-HE
2.8 (41)2.5 (36)2.2 (32)2.4 (35)215/55 R 162.5L Duratec-ST
2.8 (41)2.5 (36))2.2 (32)2.4 (35)235/45 R 172.5L Duratec-ST
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/40 R 182.5L Duratec-ST
2.8 (41)2.5 (36)2.2 (32)2.4 (35)205/55 R 161.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)215/55 R 161.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/45 R 171.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/40 R 181.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)215/55 R 162.0L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/45 R 172.0L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/40 R 182.0L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)215/55 R 162.2L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/45 R 172.2L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/40 R 182.2L Duratorq-TDCi
Continuous speed in excess of 160 km/h (100mph)
Tyre pressures
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.5 (36)2.2 (32)2.2 (32)205/55 R 161.6L Duratec-Ti-VCT
220
Wheels and tyres
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.5 (36)2.2 (32)2.2 (32)215/55 R 162.0L Duratec-HE
2.8 (41)2.5 (36)2.2 (32)2.2 (32)235/45 R 172.0L Duratec-HE
2.8 (41)2.5 (36)2.2 (32)2.2 (32)235/40 R 182.0L Duratec-HE
2.8 (41)2.6 (38)2.2 (32)2.4 (35)215/55 R 162.3L Duratec-HE
2.8 (41)2.6 (38)2.2 (32)2.4 (35)235/45 R 172.3L Duratec-HE
2.8 (41)2.6 (38)2.2 (32)2.4 (35)235/40 R 182.3L Duratec-HE
3 (44)2.7 (39)2.3 (33)2.5 (36)215/55 R 162.5L Duratec-ST
3 (44)2.7 (39)2.3 (33)2.5 (36)235/45 R 172.5L Duratec-ST
3 (44)2.7 (39)2.3 (33)2.5 (36)235/40 R 182.5L Duratec-ST
3 (44)2.6 (38)2.2 (32)2.4 (35)205/55 R 161.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)215/55 R 161.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/45 R 171.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/40 R 181.8L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)215/55 R 162.0L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/45 R 172.0L Duratorq-TDCi
2.8 (41)2.5 (36)2.2 (32)2.4 (35)235/40 R 182.0L Duratorq-TDCi
3 (44)2.7 (39)2.3 (33)2.5 (36)215/55 R 162.2L Duratorq-TDCi
3 (44)2.7 (39)2.3 (33)2.5 (36)235/45 R 172.2L Duratorq-TDCi
3 (44)2.7 (39)2.3 (33)2.5 (36)235/40 R 182.2L Duratorq-TDCi
221
Wheels and tyres
VEHICLE IDENTIFICATIONPLATE
E85610C
B
E D
A
Vehicle identification numberA
Gross vehicle weightB
Gross train weightC
Maximum front axle weightD
Maximum rear axle weightE
The vehicle identification number andmaximum weights are shown on a platelocated on the lock side of the passengerdoor aperture at the bottom.
VEHICLE IDENTIFICATIONNUMBER (VIN)
E87496
The vehicle identification number isstamped into the floor panel on theright-hand side, beside the front seat. It isalso shown on the left-hand side of theinstrument panel.
222
Vehicle identification
TECHNICALSPECIFICATIONS
Vehicle dimensions
4-door
DA
EB
C
E87088
Dimension inmm(inches)
Dimension descriptionItem
4 844 (190.7)Maximum lengthA
2 078 (81.8)Overall width including exterior mirrorsB
1 453 - 1 500(57.2 - 59.1)Overall height at EC kerb weightC
223
Technical specifications
Dimension inmm(inches)
Dimension descriptionItem
2 850 (112.2)WheelbaseD
1 579 - 1 589 (62.2 -62.6)Front trackE
1 595 - 1 605 (62.8 -63.2)Rear trackE
5-door
DA
EB
C
E87089
224
Technical specifications
Dimension inmm(inches)
Dimension descriptionItem
4 778 - 4 802 (188.1 -189.1)Maximum lengthA
2 078 (81.8)Overall width including exterior mirrorsB
1 453 - 1 500(57.2 - 59.1)Overall height at EC kerb weightC
2 850 (112.2)WheelbaseD
1 579 - 1 589 (62.2 -62.6)Front trackE
1 595 - 1 605 (62.8 -63.2)Rear trackE
225
Technical specifications
Estate
DA
EB
C
E87090
Dimension inmm(inches)
Dimension descriptionItem
4 830 - 4 856 (190.2 -191.2)Maximum lengthA
2 078 (81.8)Overall width including exterior mirrorsB
1 466 - 1 512(57.7 - 59.5)Overall height at EC kerb weight without roof barsC
1 502 - 1 548 (59.1 - 61)Overall height at EC kerb weight including roof barsC
2 850 (112.2)WheelbaseD
226
Technical specifications
Dimension inmm(inches)
Dimension descriptionItem
1 579 - 1 589 (62.2 -62.6)Front trackE
1 595 - 1 605 (62.8 -63.2)Rear trackE
Towing equipment dimensions
4-door
C
A
FG
D
B
E
E87091
Dimension inmm(inches)
Dimension descriptionItem
102 (4)Bumper – end of tow ballA
1 (0.04)Attachment point – centre of tow ballB
227
Technical specifications
Dimension inmm(inches)
Dimension descriptionItem
1 150 (45.3)Wheel centre – centre of tow ballC
438 (17.2)Centre of tow ball – side memberD
876 (34.5)Inner side of side memberE
434 (17.1)Centre of tow ball – centre 1. attachment pointF
707 (27.8)Centre of tow ball – centre 2. attachment pointG
5-door
C
A
FG
D
B
E
E87092
228
Technical specifications
Dimension inmm(inches)
Dimension descriptionItem
100 (3.9)Bumper – end of tow ballA
90 (3.5)Bumper – end of tow ball (with sport bumper)A
1 (0.04)Attachment point – centre of tow ballB
1 082 (42.6)Wheel centre – centre of tow ballC
438 (17.2)Centre of tow ball – side memberD
876 (34.5)Inner side of side memberE
364 (14.3)Centre of tow ball – centre 1. attachment pointF
637 (25.1)Centre of tow ball – centre 2. attachment pointG
Estate
C
A
FG
D
B
E
E87093
229
Technical specifications
Dimension inmm(inches)
Dimension descriptionItem
100 - 110 (3.9 - 4.3)Bumper – end of tow ballA
1 (0.04)Attachment point – centre of tow ballB
1 134 - 1 144 (44.7 - 45)Wheel centre – centre of tow ballC
438 (17.2)Centre of tow ball – side memberD
876 (34.5)Inner side of side memberE
419 - 429 (16.5 - 16.9)Centre of tow ball – centre 1. attachment pointF
692 - 702 (27.2 - 27.6)Centre of tow ball – centre 2. attachment pointG
230
Technical specifications
GENERAL INFORMATION
CAUTION
Using the system with the engine offwill drain the battery.
This section describes the functions andfeatures of the Bluetooth mobile phonehands free system.
The Bluetooth mobile phone part of thesystem provides interaction with the audioor navigation system and your mobilephone. It allows you to use the audio ornavigation system to make and receivecalls without having to use your mobilephone.
Compatibility of phones
CAUTION
As no common agreement exists,mobile phone manufacturers are ableto implement a variety of profiles in
their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insome cases may significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.
Please visit the website www.ford-mobile-connectivity.com for fulldetails.
Phoneswith Symbian operatingsystem
Note: Certain phones require a specialfile to be installed to enable full phonebookaccess via Bluetooth.
This is referred to as a SIS file and will beavailable to download via the Ford websitewww.ford-mobile-connectivity.com.
TELEPHONESETUP
Phonebook
Note: It may be necessary to confirmphonebook access to the Bluetoothsystem via the mobile phone.
After start up access to the phonebooklist can be delayed for several minutes,depending upon the size.
Phonebook categories
Depending on your phonebook entry,different categories can be displayed inthe audio unit.
For example:
MobileM
OfficeO
HomeH
FaxF
Note: Entries may be displayed withouta category attachment.
The category can also be indicated as anicon:
E87990
Phone
E87991
Mobile
E87992
Home
E87993
Office
E87994
Fax
231
Telephone
Making a phone an activephone
When using the system for the first time,no phone is connected to the system.
After switching on the ignition and theaudio unit, the Bluetooth phone must bebonded to the system.
Bluetooth phone
After bonding a Bluetooth phone to thesystem, this becomes the active phone.For further information refer to the phonemenu.
Select the phone from the active phonemenu.
Turning the ignition and radio or navigationunit back on again, the last active phoneis picked up by the system.
Note: In some cases the Bluetoothconnection must also be confirmed onthe phone.
BondanotherBluetoothphone
Bond a new Bluetooth phone asdescribed in the requirements for aBluetooth connection.
Phones stored in the system areaccessible by using the phone list on theaudio unit.
Note: A maximum of six devices may bebonded. If six Bluetooth devices havealready been bonded, one of these hasto be debonded in order to bond a newdevice.
BLUETOOTHSETUP
Before you can use your telephone withyour vehicle it must be bonded to thevehicle telephone system.
Handling of phones
Up to six Bluetooth devices can bebonded to the vehicle system.
Note: If there is an ongoing call when thephone in use is selected as the new activephone, the call is transferred to the vehicleaudio system.
Note: Even if connected to the carsystem, your phone can still be used inthe usual way.
Requirements for Bluetoothconnection
The following are required before aBluetooth phone connection can bemade.
1. The Bluetooth feature must beactivated on the phone and on theaudio unit. Make sure the Bluetoothmenu option in the audio unit is set toON. For information on phonesettings, refer to your phone userguide.
2. The private mode must not beactivated on the Bluetooth phone.
3. Search for audio device.4. Select Ford Audio.5. Enter the code number shown on the
vehicle display using the phonekeypad. If no code number is shownon the display, enter the Bluetooth PINnumber 0000 using the phonekeypad. Now enter the Bluetooth PINnumber shown on the vehicle display.
Note: A phone call will be disconnectedif the audio unit is switched off. If theignition key is turned to the off positionthe phone call will remain in progress.
232
Telephone
TELEPHONECONTROLS
Remote control
Voice, accept and reject button
1 2
E87662
Voice button1
Accept and reject button2
The VOICE button is used to activate orswitch off the Voice control.
On vehicles with an accept and rejectbutton, phone calls can be accepted andrejected by pressing the appropriatebutton.
Note: Some audio units have the acceptand reject buttons on the front bezel.These operate in the same way.
USINGTHE TELEPHONE -VEHICLESWITHOUT:NAVIGATIONSYSTEM
This chapter describes the phonefunctions of the audio unit.
Note: Refer to your audio guide fordetails of the controls.
An active phone must be present.
Even if connected to the audio unit, yourphone can still be used in the usual way.
Note: You can exit the phone menu bypressing any source buttonCD,AM/FMor AUX.
Making a call
Dialling a number using voicecontrol
Phone numbers can be dialled using voicecontrol. See Telephone commands(page 250).
Diallinganumberusingtheaddressbook
You can access your phone addressbook via Bluetooth. The entries will appearin the unit display.
1. Press the PHONE or the call acceptbutton.
2. Press the MENU button.
3. Keep pressing theMENUbutton untilPHONEBOOK appears.
4. Press the seek buttons to select thedesired phone number.
Note: Press and hold the seek button toskip to the next letter in the alphabet.
5. Press the PHONE or the call acceptbutton to dial the selected phonenumber.
Diallinganumberusingtheaddressbook - Sony radio
You can access your phone addressbook via Bluetooth. The entries will appearin the unit display.
1. Press the PHONE button.
2. Press the seek button until the phonebook is shown.
3. Press the up/down arrow buttons toselect the desired phone number.
Note:Press and hold the up/down arrowbuttons to skip to the next letter in thealphabet.
233
Telephone
4. Press the PHONE or the call acceptbutton to dial the selected phonenumber.
Dialling a number using thetelephone keypad
If you have an audio unit with a telephonekeypad (buttons 0-9, * and #):
1. Press the call accept button. PressthePHONEbutton if you have a Sonyradio.
2. Dial the number using the telephonekeypad on the audio unit.
3. Press the call accept button.
Note: If you enter an incorrect digit whilstentering a phone number, press the seekleft button to erase the last digit. A longpress will erase the complete string ofdigits.
Press and hold 0 to enter a + digit.
Ending a call
Calls can be ended by pressing the callreject button.
Audio units without a telephone keypadcan also end a call by pressing eitherPHONE, CD, AM/FM or ON/OFF, orby pressing the MODE button on theremote control
Redialling a number
1. Press the PHONE or the call acceptbutton.
2. Press the MENU button.
3. Select the CALLOUT list or theCALL IN list. On some audio units,select the MISSED, INCOMING orOUTGOING calls list.
Note: If the active phone does notprovide a call out list, the last outgoing callnumber/entry can be redialled.
4. Press the seek button on the audiounit.
5. Press the PHONE or the call acceptbutton to dial the desired phonenumber.
Redialling a number - Sony radio
1. Press the PHONE or the call acceptbutton.
2. Press the seek button until the desiredlist is displayed.
Note: If the active phone does notprovide a call out list, the last outgoing callnumber/entry can be redialled.
3. Press the up/down buttons to selectthe desired phone number.
4. Press the PHONE or the call acceptbutton to dial the phone number.
Redialling the last dialled number -Sony radio
1. Press the call accept button.
2. Press the call accept button a secondtime to dial the number.
Receiving an incoming call
Accepting an incoming call
Incoming calls can be accepted bypressing either the call accept button, thePHONE button or theMODE button onthe remote control.
Rejecting an incoming call
Incoming calls can be rejected bypressing the call reject button.
Audio units without a telephone keypadcan also reject a call by pressing eitherPHONE, CD, AM/FM or ON/OFF.
Receiving a second incomingcall
Note: The second incoming call functionmust be activated in your phone.
234
Telephone
If there is an incoming call whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.
Accepting a second incoming call
Second incoming calls can be acceptedby pressing either the call accept button,thePHONEbutton, or theMODEbuttonon the remote control.
Rejecting a second incoming call
Second incoming calls can be rejected bypressing the call reject button. Unitswithout a telephone keypad can alsoreject a second incoming call by pressingthe CD button, or the AM/FM button.
Muting themicrophone
During a call, it is possible to mute themicrophone. Whilst muted, confirmationwill appear in the display.
Audio unitswith green call acceptbutton
Press the call accept button. Press thebutton once again to turn this function off.
Audio unitswithout green callaccept button
Press the seek up or down button. Pressthe button once again to turn this functionoff.
Changing the active phone
Note: Phones must be bonded to thesystem before they can be made active.
Using the station storage button
Note: This process is only for audio unitswithout a telephone keypad.
1. Press the PHONE button on theaudio unit.
2. Press the preset number required(using the station preset buttons 1 -6).
Using the audio unitmenu
Note: After bonding a phone to thesystem, this becomes the active phone.
1. Press the PHONE or call acceptbutton.
2. Press theMENU button on the audiounit.
3. Select the ACTIVEPHONE optionon the audio unit.
4. Scroll through the different storedphones by using the seek buttons todisplay the bonded phones.
5. Press theMENU button to select thephone which is to be the active phone.
Debonding a bonded phone
A bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.
1. Press the PHONE or call acceptbutton.
2. Press theMENU button on the audiounit.
3. Select the DEBOND option on theaudio unit.
4. Scroll through the different phones byusing the seek buttons and display thephone to be debonded.
5. Press theMENU button to select thephone which is to be debonded.
Debonding a bonded phone -Sony radio
A bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.
1. Press the PHONE button.
235
Telephone
2. Press the up/down arrow buttons untilyou reach the DEBOND option.
3. Scroll through the different phones byusing the seek buttons and display thephone to be debonded.
4. Press the OK button to be debond.
USINGTHE TELEPHONE -VEHICLESWITH:NAVIGATIONSYSTEM
This chapter describes the phonefunctions of the Navigation System.
Note: Refer to your Navigation Systemguide for details of the controls.
An active phone must be present.
Even if connected to the NavigationSystem, your phone can still be used inthe usual way.
Making a call
Dialling a number
Phone numbers can be dialled using voicecontrol. See Voice control (page 238).
Ending a call
Calls can be ended by pressing either theEND button, the MODE button on theremote switch or theON/OFF button onthe navigation system.
Redialling a number
1. Press thePHONE button on the unit.
2. Select REDIAL.
Receiving an incoming call
Accepting an incoming call
Incoming calls can be accepted bypressing either the call accept button, theMODEbutton on the remote control, thePHONE button on the unit or by usingthe ACCEPT option in the menu.
Rejecting an incoming call
Incoming calls can be rejected bypressing either the call reject button, theCD orAM/FM buttons on the unit, or byusing the REJECT option in the menu.
Receiving a second incomingcall
Note: The second incoming call functionmust be activated in your phone.
If there is an incoming call, whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.
Accepting a second incoming call
Second incoming calls can be acceptedby pressing either the call accept button,theMODEbutton on the remote control,the PHONE button on the unit or byusing the ACCEPT option in the menu.
Note: This will cancel the ongoing call.
Rejecting a second incoming call
Second incoming calls can be rejected bypressing either the call reject button, orone of the following buttons on the unit:CD, AM/FM.
Muting themicrophone
During a call, it is possible to mute themicrophone. Whilst muted, confirmationwill appear in the display.
236
Telephone
DVDnavigation units
Press the mute button (symbol of amicrophone with a line through it). Pressthe button once again to turn this functionoff.
CDnavigation units
Press the microphone mute button. Pressthe button once again to turn this functionoff.
Changing the active phone
Note: Phones must be bonded to thesystem before they can be made active.
Note: After bonding a phone to thesystem, this becomes the active phone.
1. Press thePHONE button on the unit.
2. Using the BTSETTINGS option inthe menu, select the active phonefrom the list.
Debonding a bonded phone
A bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.
1. Press thePHONE button on the unit.
2. Select the BTSETTINGS option inthe menu.
3. Select the DEBOND option in themenu.
4. Select the phone from the list.
237
Telephone
PRINCIPLEOFOPERATION
CAUTION
Using the system with the engine offwill drain the battery.
Voice recognition enables operation ofthe system without the need to divert yourattention from the road ahead in order tochange settings, or receive feedbackfrom the system.
Whenever you issue one of the definedcommands with the system active, thevoice recognition system converts yourcommand into a control signal for thesystem. Your inputs take the form ofdialogues or commands. You are guidedthrough these dialogues byannouncements or questions.
Please familiarise yourself with thefunctions of the system before using voicerecognition.
Supported commands
The voice control system allows you tocontrol the following vehicle functions:
• Bluetooth phone
• radio
• CD Player/CD Changer
• external device (USB)
• external device (iPod)
• SD card
• automatic climate control
• navigation system (DVD units only -refer to separate DVD navigationhandbook).
Note: The voice control system islanguage specific. If you require thesystem to operate in another languageplease consult your dealer.
System response
As you work through a voice session thesystem will prompt you with a beep toneeach time the system is ready to proceed.
Do not try to give any commands until thebeep tone has been heard. The voicecontrol system will repeat each spokencommand back to you.
If you are not sure how to continue say"HELP" for assistance or "CANCEL" if youdo not wish to continue.
The "HELP" function provides only asubset of the available voice commands.Detailed explanations of all possible voicecommands can be found on the followingpages.
Voice commands
All voice commands should be given usinga natural speaking voice, as if speaking toa passenger or on the phone. Your voicelevel should be dependant on thesurrounding noise level inside or outsidethe vehicle but do not shout.
USINGVOICECONTROL
Systemoperation
The order and content of the voicecontrols are given in the following lists. Thetables show the sequence of user voicecommands and system responses foreach available function.
<> indicates a number or stored name tagto be inserted by the user.
Short cuts
There are a number of voice commandshort cuts available, which allow you tocontrol some vehicle features withouthaving to follow the complete commandmenu. These are:
238
Voice control
• phone: "MOBILE NAME", "DIALNUMBER", "DIAL NAME", and"REDIAL"
• CD player/CD changer: "DISC" and"TRACK"
• automatic climate control:"TEMPERATURE", "AUTO MODE","DEFROSTING/DEMISTING ON" and"DEFROSTING/DEMISTING OFF"
• radio: "TUNE NAME"
• external device (USB): "TRACK"
• external device (iPod): "TRACK"
• SD card: "TRACK".
Start communicatingwith thesystem
Before you can start talking to the systemyou first have to press the VOICE orMODE button for each operation andwait until the system answers with a beep.See (page 238).
Press the button again to cancel the voicesession.
Name tag
The name tag functionality can supportthe phone, audio and navigation featuresby using the "STORE NAME" function. Youcan assign name tags to items such asfavourite radio stations and personalphone contacts. See Audio unitcommands (page239). SeeTelephonecommands (page 250). SeeNavigation systemcommands(page 254).
• Store up to 20 name tags per function.
• The average recording time for eachname tag is approximately 2-3seconds.
AUDIOUNITCOMMANDS
CDPlayer
You can control playback directly by voicecontrol.
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"CDPLAYER"
"HELP"
"PLAY"
"TRACK"*
"SHUFFLE ALL"
"SHUFFLE FOLDER"**
"SHUFFLE OFF"
"REPEAT FOLDER"**
239
Voice control
"CDPLAYER"
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.
** Only available if the CD contains audio data files like MP3 or WMA.
Track
You can choose a track on your CDdirectly.
SystemanswerUser saysSteps
"CD PLAYER""CD PLAYER"1
"TRACK NUMBER PLEASE""TRACK"*2
"TRACK <number>""<a number between 1 and 99>"**3
* Can be used as a shortcut.
** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
Shuffle all
To set random playback.
SystemanswerUser saysSteps
"CD PLAYER""CD PLAYER"1
"SHUFFLE ALL"2
CDChanger
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
240
Voice control
"CDCHANGER"
"HELP"
"PLAY"
"DISC"*
"TRACK"*
"SHUFFLE ALL"
"SHUFFLE CD"
"SHUFFLE FOLDER"**
"SHUFFLE OFF"
"REPEAT CD"
"REPEAT FOLDER"**
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.
** Only available if the CD contains audio data files like MP3 or WMA.
Disc
If you have a CD changer you can choosethe disc number.
SystemanswerUser saysSteps
"CD CHANGER""CD CHANGER"1
"DISC NUMBER PLEASE""DISC"*2
"DISC <number>""<a number between 1 and 6>"3
* Can be used as a shortcut.
Track
You can choose a track on your CDdirectly.
241
Voice control
SystemanswerUser saysSteps
"CD CHANGER""CD CHANGER"1
"TRACK NUMBER PLEASE""TRACK"*2
"TRACK <number>""<a number between 1 and 99>"**3
* Can be used as a shortcut.
** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
Shuffle CD
To set random playback within the CDcontents.
SystemanswerUser saysSteps
"CD CHANGER""CD CHANGER"1
"SHUFFLE CD"2
Radio
The radio voice commands support thefunctionality of the radio and allow you totune radio stations by voice control.
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu.
"RADIO"
"HELP"
"AM"
"FM"
"TUNE NAME"*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
242
Voice control
"RADIO"
"PLAY"
* Can be used as a shortcut.
Tune frequency
This function allows you to tune your radioby voice commands.
SystemanswerUser saysSteps
"RADIO""RADIO"1
"AM FREQUENCY PLEASE""AM"2
"FM FREQUENCY PLEASE""FM"
"TUNE <frequency>""<frequency>"*3
* The frequency may be entered in a variety of ways. Refer below for representativeexamples.
FM band: 87.5 - 108.0 in increments of 0.1
• "Eighty nine point nine" (89.9)
• "Ninety" (90.0)
• "One hundred point five" (100.5)
• "One zero one point one" (101.1)
• "One zero eight" (108.0)
AM/MW band: 531 - 1602 in incrementsof 9
AM/LW band: 153 - 281 in increments of1
• "Five thirty one" (531)
• "Nine hundred" (900)
• "Fourteen forty" (1440)
• "Fifteen zero three" (1503)
• "Ten eighty" (1080)
Store name
If you have tuned a radio station, you canstore it with a name in the directory.
SystemanswerUser saysSteps
"RADIO""RADIO"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED"
243
Voice control
Tune name
This function allows you to call up a storedradio station.
SystemanswerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""TUNE NAME"*2
"TUNE <name>""<name>"3
* Can be used as a shortcut.
Delete name
This function allows you to delete a storedradio station.
SystemanswerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"DELETED""YES"4
"COMMAND CANCELLED""NO"
Play directory
This function allows you to let the systemtell you all of the stored radio stations.
SystemanswerUser saysSteps
"RADIO""RADIO"1
"PLAY <DIRECTORY>""PLAY DIRECTORY"2
Delete directory
This function allows you to delete allstored radio stations at once.
244
Voice control
SystemanswerUser saysSteps
"RADIO""RADIO"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"RADIO DIRECTORY DELETED""YES"3
"COMMAND CANCELLED""NO"
Play
This function switches the audio sourceto the radio mode.
SystemanswerUser saysSteps
"RADIO""RADIO"1
"PLAY"2
Auxiliary input
This function allows you to switch theaudio source to the attached auxiliaryinput device.
SystemanswerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"LINE IN""LINE IN"2
External devices - USB
These voice commands support thefunctionality of an external USB devicewhich may be connected to the audiounit.
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"EXTERNALDEVICE", "USB"
"HELP"
245
Voice control
"EXTERNALDEVICE", "USB"
"PLAY"
"TRACK"*
"PLAYLIST"**
"FOLDER"**
"SHUFFLE ALL"
"SHUFFLE FOLDER"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT FOLDER"
"REPEAT OFF"
* Can be used as a shortcut.
** Playlists and folders activated by voice control must be assigned special filenames.See General information (page 257).
USBplay
This function allows you to switch theaudio source to the attached USB device.
SystemanswerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"USB""USB"2
"PLAY"3
USBTrack
You can choose a track on your USBdevice directly.
246
Voice control
SystemanswerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"USB""USB"2
"TRACK NUMBER PLEASE""TRACK"3
"TRACK <number>""<a number between 1 and 99>"*4
* Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
External devices - iPod
These voice commands support thefunctionality of an iPod which may beconnected to the audio unit.
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"EXTERNALDEVICE", "IPOD"
"HELP"
"PLAY"
"TRACK"*
"PLAYLIST"**
"SHUFFLE ALL"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.
** Playlists activated by voice control must be assigned special filenames. SeeGeneralinformation (page 257).
247
Voice control
iPod Track You can choose a track off the all titles listof your iPod directly.
SystemanswerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"IPOD""IPOD"2
"TRACK NUMBER PLEASE""TRACK"*3
"TRACK <number>""<a number between 1 and 99>"**4
* Can be used as a shortcut.
** Additionally, numbers can be spoken as up to five single digits (for example "5", "2","4", "5", "3" for track 52453), to a limit of 65535.
iPod playlist
You can choose a playlist from your iPoddirectly.
SystemanswerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"IPOD""IPOD"2
"PLAYLIST NUMBER PLEASE""PLAYLIST"*3
"PLAYLIST <number>""<a number between 1 and 10>"4
* Playlists activated by voice control must be assigned special filenames. SeeGeneralinformation (page 257).
SDCard
These voice commands support thefunctionality of an SD card which hassuitable audio files written to it.
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"SDCARD"
"HELP"
248
Voice control
"SDCARD"
"PLAY"
"TRACK"*
"SHUFFLE ALL"
"SHUFFLE FOLDER"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT FOLDER"
"REPEAT OFF"
* Can be used as a shortcut.
SDcard play
This function allows you to switch theaudio source to the SD card audio files.
SystemanswerUser saysSteps
"SD CARD""SD CARD"1
"PLAY"2
SDcard track
You can choose a track on your SD carddirectly.
SystemanswerUser saysSteps
"SD CARD""SD CARD"1
"TRACK NUMBER PLEASE""TRACK"*2
"TRACK <number>""<a number between 1 and 99>"**3
* Can be used as a shortcut.
** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245).
249
Voice control
TELEPHONECOMMANDS
Phone
Your phone system allows you to createan additional phonebook. The storedentries can be dialled by voice control.Phone numbers stored by using voicecontrol are stored on the vehicle systemand not in your phone.
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"PHONE"
"HELP"
"MOBILE NAME"*
"DIAL NUMBER"*
"DIAL NAME"*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
"REDIAL"*
"ACCEPT CALLS"
"REJECT CALLS"
* Can be used as a shortcut.
Create a phonebook
Store name
New entries can be stored with the"STORE NAME" command. This featurecan be used to dial a number by callingup the name instead of the full phonenumber.
250
Voice control
SystemanswerUser saysSteps
"PHONE""PHONE"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED""NUMBER PLEASE"
"<phone number>""<phone number>"5
"STORING NUMBER""STORE"6"<phone number>"
"NUMBER STORED"
Delete name
Stored names can also be deleted fromthe directory.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"<name> DELETED""YES"4
"COMMAND CANCELLED""NO"
Play directory
Use this function to let the system tell youall stored entries.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"PLAY DIRECTORY""PLAY DIRECTORY"2
251
Voice control
Delete directory This function allows you to delete allentries in one go.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"DIRECTORY DELETED""YES"3
"COMMAND CANCELLED""NO"
Phone functions
Mobile name
This function allows you to access phonenumbers stored with a name tag in yourmobile phone.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"MOBILE NAME" "<phonedependent dialogue>"
"MOBILE NAME"*2
* Can be used as a shortcut.
Dial number
Phone numbers can be dialled after givingthe name tag voice command.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"NUMBER PLEASE""DIAL NUMBER"*2
"<phone number>"<phone number>"3CONTINUE?"
"DIALLING""DIAL"4
"<repeat last part of number>"CORRECTION"
252
Voice control
SystemanswerUser saysSteps
CONTINUE?"
* Can be used as a shortcut.
Dial name
Phone numbers can be dialled after givingthe name tag voice command.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DIAL NAME"*2
"DIAL <name>""<name>"3"CONFIRM YES OR NO"
"DIALLING""YES"4
"COMMAND CANCELLED""NO"
* Can be used as a shortcut.
Redial
This function allows you to redial the lastdialled phone number.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"REDIAL""REDIAL"*2"CONFIRM YES OR NO"
"DIALLING""YES"3
"COMMAND CANCELLED""NO"
* Can be used as a shortcut.
253
Voice control
DTMF (Tone dialling)
This function transfers spoken numbersinto DTMF tones. For example, to makea remote enquiry to your home answeringmachine or to enter a PIN number etc.
Note: DTMF can only be used during anongoing call. Press the VOICE button andwait for the system prompt.
Can only be used with vehicles installedwith a dedicated VOICE button.
SystemanswerUser saysSteps
"NUMBER PLEASE"1
"<numbers 1 to 9, zero, hash, star>"2
Main settings
Reject calls
Calls can be set to be automaticallyrejected using voice control.
SystemanswerUser saysSteps
"PHONE""PHONE"1
"REJECT CALLS""REJECT CALLS"2
"ACCEPT CALLS""ACCEPT CALLS"*
* use this command to turn the reject mode off
NAVIGATIONSYSTEMCOMMANDS
Please refer to your separate Navigationhandbook for details of the commandmenus.
CLIMATECONTROLCOMMANDS
Climate
The climate voice commands supportsthe functionality of the fan speed,temperature and mode settings. Not allfunctions are available on all vehicles.
Overview
The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
254
Voice control
"CLIMATE"
"HELP"
"FAN"*
"DEFROSTING/DEMISTING ON"*
"DEFROSTING/DEMISTING OFF"*
"TEMPERATURE"*
"AUTO MODE"*
* Can be used as a shortcut. On vehicles fitted with an English language module the"FAN" shortcut is not available.
Fan
This function allows you to adjust the fanspeed.
SystemanswerUser saysSteps
"CLIMATE""CLIMATE"1
"FAN SPEED PLEASE""‘FAN"*2
"FAN MINIMUM""MINIMUM"
3 "FAN <number>""<a number between 1 and 7>"
"FAN MAXIMUM""MAXIMUM"
* Can be used as a shortcut. On vehicles fitted with an English language module the"FAN" shortcut is not available.
255
Voice control
Defrosting/Demisting
SystemanswerUser saysSteps
"CLIMATE""CLIMATE"1
"DEFROSTING ON/DEMISTING ON""DEFROSTING ON/DEMISTING
ON"*
2"DEFROSTING OFF/DEMISTING
OFF""DEFROSTING OFF/DEMISTING
OFF"*
* Can be used as a shortcut.
Temperature
This function allows you to adjust thetemperature.
SystemanswerUser saysSteps
"CLIMATE""CLIMATE"1
"TEMPERATURE PLEASE""TEMPERATURE"*2
"TEMPERATURE MINIMUM""MINIMUM"
3 "TEMPERATURE <number>""<a number between 15 and 29 °C
with 0.5 increments>" or "<anumber between 59 and 84 °F>"
"TEMPERATURE MAXIMUM""MAXIMUM"
* Can be used as a shortcut.
Automode
SystemanswerUser saysSteps
"CLIMATE""CLIMATE"1
"AUTO MODE""AUTO MODE"*2
* Can be used as a shortcut. Can be deactivated by selecting a different temperatureor fan speed.
256
Voice control
GENERAL INFORMATION
CAUTIONSTake care when handling externaldevices with exposed electricalconnectors (such as the USB plug).
Always replace the protective cap/shieldwhen possible. There may be a risk ofelectrostatic discharge causing damageto the device.
Do not touch or handle the USBsocket in the vehicle. Cover thesocket when not in use.
Only use USB Mass-Storage devicecompliant devices.
Always switch your audio unit to adifferent source (for example theradio) before unplugging the USB
device.
Do not install or connect USB hubsor splitters.
Note: The system is only designed torecognize and read suitable audio filesfrom a USB device that conforms to theUSB Mass-Storage device class or aniPod. Not all available USB devices can beguaranteed to function with the system.
Note: It is possible to connect compatibledevices with a trailing USB lead as well asthose that plug into the vehicle USBsocket directly (for example USB memorysticks and pen drives).
Note: Some USB devices with a higherpower consumption may not becompatible (for example some larger harddrives).
Note: Access time to read the files onthe external device will vary dependingupon factors such as the file structure,size and device content.
The system supports a range of externaldevices, to fully integrate with your audiounit via the USB and auxiliary inputsockets. Once connected, control of theexternal device is possible via the audiounit.
A list of typical compatible devices areshown below:• USB memory sticks
• USB portable hard drives
• MP3 players with USB connection
• iPod media players (refer towww.ford-mobile-connectivity.com for latestcompatibility list).
The system is USB 2.0 full speedcompatible, USB 1.1 host compliant andsupports FAT 16/32 file systems.
Information on audio filestructuresforexternaldevices
USB
Create only a single partition on the USBdevice.
If playlists are created, they must containcorrect file paths referenced to the USBdevice. It is recommended to create theplaylist after the audio files have beentransferred to the USB device.
Playlists must be created in .m3u format.
Audio files must be in .mp3 format.
Do not exceed the following limits:• 1000 items per folder (files, folders and
playlists)• 5000 folders per USB device
(including playlists)• 8 subfolder levels.
257
Connectivity
To enable voice control for customplaylists and folders, follow the procedurebelow:• Create folders named with the
structure "Ford<*>" where <*> is anumber 1-10. For example "Ford3"without an extension.
• Create playlists named with thestructure "Ford<*>.m3u"where <*>is a number 1-10. For example"Ford5.m3u" without any spacebetween "Ford" and the number.
Thereafter, custom folders and playlistswill be selectable with voice control. SeeAudio unit commands (page 239).
iPod
To enable voice control for customplaylists, create playlists named with thestructure "Ford<*>"where <*> is anumber 1-10. For example "Ford7"without any space between "Ford" andthe number.
Thereafter, playlists will be selectable withvoice control. See Audio unitcommands (page 239).
CONNECTINGANEXTERNALDEVICE
WARNING
Make sure the external device issecurely mounted within the vehicle,and that trailing connections do not
obstruct any of the driving controls.
External devices may be connected usingthe auxiliary input socket and the USBport. See Auxiliary input (AUX IN)socket (page 125). SeeUSBport (page126).
Connection
Plug in the device, and if necessarysecure it to prevent movement within thevehicle.
Connecting an iPod
For optimum convenience and audioquality, we recommend that you purchasea dedicated single connection leadavailable from your dealer.
Alternatively, it is possible to connect youriPod using the standard iPod USB cableand a separate 3.5mm audio jack lead. Ifusing this method preset the iPod volumeto maximum and turn off any equalizersettings before making the connections:
• Connect the headphone output of theiPod to the AUX IN socket.
• Connect the USB cable from the iPodto the vehicle USB socket.
CONNECTINGANEXTERNALDEVICE - VEHICLESWITH:BLUETOOTH
Connecting aBluetooth audiodevice
CAUTION
As various standards exist,manufacturers are able to implementa variety of profiles in their Bluetooth
devices. Because of this, anincompatibility can occur between theBluetooth device and the system, whichin some cases may limit systemfunctionality. To avoid this situation, onlyrecommended devices should be used.
Please visit the websitewww.ford-mobile-connectivity.comfor full details.
258
Connectivity
Bonding the device
Note: Some audio and navigation unitshave a separate Bluetooth audio menu.Use this to access setup and control.
To connect the device to the systemfollow the same procedure as forBluetooth hands free phones. SeeBluetooth setup (page 232).
Operating the device
Select Bluetooth audio as the activesource.
Tracks can be accessed by skippingforwards and backwards using thesteering wheel controls, or directly fromthe audio unit controls.
USINGAUSBDEVICE
Various icons are used to identify typesof audio file, folders etc.
E100029
USB device is the active source
E100022
Folder
E100023
Playlist
E100024
Album
E100025
Artist
E100026
Filename
E100027
Track title
E100028
Information not available
Sony radio
Operation
Select the USB device as the audiosource by repeatedly pressing theCD/AUX button until USB appears in thedisplay. After first connecting the USBdevice, the first track within the first folderwill start to play automatically.Subsequently, following audio sourceswitching, the position of playback on theUSB device is remembered.
To browse the device contents, press theup/down arrow key or the OK buttononce.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" before the list indicates that afurther level up is readable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe up/down arrow keys to scroll throughlists, and the left/right keys to move up ordown within the folder hierarchy. Onceyour desired track, playlist or folder ishighlighted, press the OK button to selectplayback.
259
Connectivity
Note: If you wish to jump to the top levelof the USB device contents, press andhold the left arrow key.
Audio control
Press the left and right arrow keys to skipbackwards and forwards through tracks.
Press and hold the left/right arrow keysto enable fast rewind/fast forward throughtrack content.
Press the up/down arrow key or the OKbutton to browse the device contents.
Press the MENU key to enter the USBmenu. It is possible to enable shuffle andrepeat functions here with respect tofolders and playlists.
Press the SCAN button to scan the wholedevice, current folder or a playlist if it is inoperation.
Press the INFO button to display thefollowing:• filename
• title
• artist
• album
• track number and playing time.
Repeated button presses will scrollthrough these displays.
CDNavigation units
Operation
Select the USB device as the audiosource by pressing the CD/AUX buttonuntil DEVICES appears in the display.Select DEVICES and then select USB fromthe available device list. After firstconnecting the USB device, the first trackwithin the first folder will start to playautomatically. Subsequently, followingaudio source switching, the position ofplayback on the USB device isremembered.
To browse the device contents, press theSELECT button once.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" to the left hand side of the displayindicates that a further level up isreadable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe rotary scroll/select button to browsethrough lists. Push the button to expandthe contents within the highlighted playlistor folder, or to commence playback of aparticular track. Press ESC to go up onelevel.
Audio control
Press the SEEK up and down keys toskip backwards and forwards throughtracks.
Press and hold theSEEK keys to enablefast rewind/fast forward through trackcontent.
Rotate or press the SELECT button tobrowse the device contents.
Press SHUFFLE or REPEAT buttons toenable shuffle and repeat functions withrespect to folders and playlists. Differentoptions may appear depending uponwhether or not a playlist is in operation.
260
Connectivity
Press the SCAN button to scan thecurrent playlist if it is in operation, or thecomplete USB device or folder.
Press the INFO button to display thefollowing:• filename
• title
• artist
• album
• track number and playing time.
DVDNavigation units
Operation
Select the USB device as the audiosource by pressing the CD/AUX buttonuntil the USB button appears to the left ofthe display. Select USB from the availabledevice list.
Note: Some devices may be shown butnot selectable, depending if the device isconnected or not.
After first connecting the USB device, thefirst track within the first folder will start toplay automatically. Subsequently, followingaudio source switching, the position ofplayback on the USB device isremembered.
To browse the device contents, press thescroll up or down arrow button.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" to the left hand side of the displayindicates that a further level up isreadable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe scroll buttons to browse through lists.Push the button to expand the contentswithin the highlighted playlist or folder, orto commence playback of a particulartrack. Press the left arrow key to go upone level.
Audio control
Press the SEEK up and down keys toskip backwards and forwards throughtracks.
Press and hold theSEEK keys to enablefast rewind/fast forward through trackcontent.
Press the scroll bar arrow keys to browsethe device contents.
Press SHUFFLE or REPEAT buttons toenable shuffle and repeat functions withrespect to folders and playlists.
Press the SCAN button to scan thecurrent playlist if it is in operation, or thecomplete USB device or folder.
Press the INFO button to display thefollowing:• filename
• title
• artist
• album
• track number and playing time.
USINGAN IPOD
Various icons are used to identify typesof audio file, folders etc.
261
Connectivity
E100030
iPod is the active source
E100031
iPod playlist
E100032
iPod artist
E100033
iPod album
E100034
iPod genre
E100035
iPod song
E100036
iPod generic category
E100037
iPod generic media file
Sony radio
Operation
Select the iPod as the audio source byrepeatedly pressing theCD/AUX buttonuntil iPod appears in the display.
The iPod menu list for browsing contentswill be available through the radio display.Navigation of the contents follows thesame principles as for iPod standaloneuse (for example search by artist, title,etc.). To browse the iPod contents, pressthe up/down arrow key or the OK buttononce.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use theup/down arrow keys to scroll through lists,and the left/right keys to move up ordown within the hierarchy. Once yourdesired track, playlist, album, artist orgenre is highlighted, press the OK buttonto select playback.
Note: If you wish to jump to the top levelof the iPod contents, press and hold theleft arrow key.
Audio control
Press the left and right arrow keys to skipbackwards and forwards through tracks.
Press and hold the left/right arrow keysto enable fast rewind/fast forward throughtrack content.
Press the up/down arrow key or the OKbutton to browse the iPod contents.
Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possibleto enable the iPod "Shuffle songs" optiondirectly from the top level.
Press the SCAN button to scan thecurrently selected tracks.
262
Connectivity
Press the INFO button to display thefollowing:• title
• artist
• track number and playing time.
Repeated button presses will scrollthrough these displays.
CDNavigation units
Operation
Select the iPod as the audio source bypressing the CD/AUX button untilDEVICES appears in the display. SelectDEVICES and then select iPod from theavailable device list.
The iPod menu list for browsing contentswill be available through the display.Navigation of the contents follows thesame principles as for iPod standaloneuse (for example search by artist, title,etc.). To browse the iPod contents, pressthe SELECT button once.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use therotary scroll/select button to browsethrough lists. Push the button to expandthe contents within the highlighted playlist,album, artist, genre or to commenceplayback of a particular track. Press ESCto go up one level.
Audio control
Press the SEEK up and down keys toskip backwards and forwards throughtracks.
Press and hold theSEEK keys to enablefast rewind/fast forward through trackcontent.
Rotate or press the SELECT button tobrowse the iPod contents.
Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possibleto enable the iPod "Shuffle songs" optiondirectly from the top level.
Press the SCAN button to scan thecurrently selected tracks.
Press the INFO button to display thefollowing:• title
• artist
• track number and playing time.
DVDNavigation units
Operation
Select the iPod as the audio source bypressing the CD/AUX button until theiPod button appears to the left of thedisplay. Select iPod from the availabledevice list.
Note: Some devices may be shown butnot selectable, depending if the device isconnected or not.
263
Connectivity
The iPod menu list for browsing contentswill be available through the display.Navigation of the contents follows thesame principles as for iPod standaloneuse (for example search by artist, title,etc.). To browse the iPod contents, pressthe scroll up or down arrow button.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use thescroll buttons to browse through lists.Push the button to expand the contentswithin the highlighted playlist, album, artist,genre or to commence playback of aparticular track. Press the left arrow keyto go up one level.
Audio control
Press the SEEK up and down keys toskip backwards and forwards throughtracks.
Press and hold theSEEK keys to enablefast rewind/fast forward through trackcontent.
Press the scroll bar arrow keys to browsethe iPod contents.
Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possibleto enable the iPod "Shuffle songs" optiondirectly from the top level.
Press the SCAN button to scan thecurrently selected tracks.
Press the INFO button to display thefollowing:• title
• artist
• track number and playing time.
264
Connectivity
ROADSAFETY
WARNINGSThe system provides you withinformation designed to help youreach your destination quickly and
safely.
For reasons of safety, the drivershould only program the systemwhen the vehicle is stationary.
The system provides no assistancewith respect to stop signs, trafficlights, areas under construction or
other important safety information.
Do not use the system until youhave familiarised yourself with itsoperation.
Only view the system display whendriving conditions permit.
Safety information
Read and follow all stated safetyprecautions. Failure to do so may increaseyour risk of collision and personal injury.Ford Motor Company shall not be liablefor any damages of any type arising fromfailure to follow these guidelines.
If detailed viewing of route instructions isnecessary, pull off the road when it is safeto do so and park your vehicle.
Do not use the navigation system tolocate emergency services.
To use the system as effectively andsafely as possible, always use the latestnavigation information. Your dealer will beable to assist with this.
265
Navigation introduction
GETTINGSTARTED
CAUTION
Using the system with the engine offwill drain the battery.
Note: You will be charged when sendingand receiving text messages.
Note:Refer to your phone handbook forall phone functions and operation.
Note: Keep the activation code (printedon the installation guide) in a safe place.
Note:Retain the activation text messagein your mobile phone inbox.
Compatibility of phones
CAUTION
As no common agreement exists,mobile phone manufacturers are ableto implement a variety of profiles in
their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insome cases may significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.
Please visit the websitewww.ford-mobile-connectivity.com forfull details.
Installing themicro SDcard
1
2
E114212
1. Remove the micro SD card from theadaptor.
2. Insert the micro SD card into themobile phone.
Activating themobile phonenavigation system
Note: The radio must be switched onbefore connecting the mobile phone tothe in-car GPS receiver.
Note: The Ford Mobile Navigation mustbe installed and activated on your mobilephone.
Note: It is possible to activate up to amaximum of three phones.
Note: Detailed instructions are availableon the micro SD card and atwww.ford-mobile-connectivity.com.
1. Switch the radio on.
266
Navigation system
E114213
2. Switch your mobile phone on and startthe "Ford Mobile Navigation".
3. Choose "Select Destination".
4. Choose "Enter Address".
5. Change route options if necessaryand start the route guidance.
6. The vehicle display will show the turninformation. Voice instructions areheard via the vehicle speakers.
Note:Your mobile phone will display yourcurrent position.
7. You are able to exit the application andcontinue your route guidance afterrestarting the application.
267
Navigation system
TYPEAPPROVALS
FCC/INDUSTRYCANADANOTICE
This device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) this devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.
FCC ID: WJLRX-42
IC: 7847A-RX42
Changes or modifications to your devicenot expressly approved by the partyresponsible for compliance can void theuser's authority to operate the equipment.
RX-42 - declaration ofconformity
We, the party responsible for compliance,declare under our sole responsibility thatthe Handset Integration product RX-42 isin conformity with the provisions of thefollowing Council Directive: 1999/5/EC. Acopy of the Declaration of Conformity canbe found at:
www.novero.com/declaration_of_conformity
The Bluetooth word mark and logos areowned by the Bluetooth SIG, Inc. and anyuse of such marks by Ford MotorCompany is under license. Othertrademarks and trade names are thoseof their respective owners.
TYPEAPPROVALS
iPod is a trademark of Apple Inc.
TYPEAPPROVALS
E114214
© 2008 NAVTEQ B.V. All rights reserved.
268
Appendices
E114220
ELECTROMAGNETICCOMPATIBILITY
WARNINGSYour vehicle has been tested andcertified to European legislationsrelating to electromagnetic
compatibility (2004/104/EC). It is yourresponsibility to ensure that anyequipment you have fitted complies withapplicable local legislations. Have anyequipment fitted by properly trainedtechnicians.
WARNINGS
Radio frequency (RF) transmitterequipment (e.g. cellular telephones,amateur radio transmitters etc.) may
only be fitted to your vehicle if they complywith the parameters shown in the tablebelow. There are no special provisions orconditions for installations or use.
Do not mount any transceiver,microphones, speakers, or anyother item in the deployment path
of the airbag system.
Do not fasten antenna cables tooriginal vehicle wiring, fuel pipes andbrake pipes.
269
Appendices
WARNINGSKeep antenna and power cables atleast 100mm from any electronic
WARNINGSmodules and airbags.
E85998
6
7
1 2 3 8
4
5
AntennaPositionsMaximumoutput powerWatt(PeakRMS)
FrequencyBandMHz
3, 850 W1 – 30
2, 350 W30 – 54
1, 2, 3, 4, 550 W68 – 87.5
1, 2, 3, 4, 550 W142 – 176
1, 2, 3, 4, 550 W380 – 512
1, 2, 3, 4, 5 (61, 71)10 W (2 W1)806 – 940
210 W1200 – 1400
1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1710 – 1885
1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1885 – 2025
All positions0.1 W2400 – 2500
1Only for GSM/3G cellular phones, with a patch antenna installed inside of the frontwindscreen.
270
Appendices
Note: After the installation of RFtransmitters, check for disturbances fromand to all electrical equipment in thevehicle, both in the standby and transmitmodes.
Check all electrical equipment:• with the ignition ON• with the engine running
• during a road test at various speeds.
Check that electromagnetic fieldsgenerated inside the vehicle cabin by thetransmitter installed do not exceed humanexposure limits specified in EU directive2004/40/EC.
271
Appendices
272
AA/C
See: Climate control....................................101About this handbook................................7ABS
See: Brakes..................................................141ABS driving hints
See: Hints on driving with ABS..................141ACC
See: Adaptive cruise control (ACC)..........151Accessories
See: Parts and accessories..........................7See: Using ACC..........................................152
Active suspension.................................146Principle of operation.................................146
Active suspensionSee: Using active suspension...................146
Adaptive cruise control (ACC).............151Principle of operation..................................151
Adaptive cruise controlSee: Using ACC..........................................152
Adaptive front lighting system(AFS).......................................................56Cornering lamps...........................................57
Adjusting the headlamps - VehiclesWith: Adaptive Front Lighting/XenonHeadlamps............................................55
Adjusting the steering wheel.................47AFS
See: Adaptive front lighting system(AFS)...........................................................56
Air conditioningSee: Climate control....................................101
Air vents...................................................101Front air vents..............................................101Rear air vents...............................................101
Alarm.........................................................44Principle of operation...................................44
Appendices...........................................268Arming the alarm.....................................46Arming the engine immobiliser.............43Ashtray....................................................122
Front ashtray...............................................122Rear ashtray................................................122
Audible warnings and indicators...........78Switching the chimes on and off...............78
Audio control............................................47Mode..............................................................47Seek...............................................................48
Audio unit commands.........................239Auxiliary input..............................................245CD Changer................................................240CD Player....................................................239External devices - iPod.............................247External devices - USB.............................245Radio............................................................242SD Card.......................................................248
Auto-dimming mirror..............................73Autolamps................................................54Automatic climate control....................104
Air distribution..............................................105Blower..........................................................105Mono mode.................................................105Recirculated air...........................................106Setting the temperature............................105Switching the air conditioning on and
off..............................................................106Switching the automatic climate control
on and off.................................................106Windscreen defrosting and
demisting.................................................106Automatic transmission........................138
Drive modes................................................139Emergency park position release
lever..........................................................140Hints on driving with an automatic
transmission............................................139Selector lever positions.............................138
Autowipers...............................................49Auxiliary heater.......................................107
Changing the remote control battery.......111Diesel auxiliary heater (depending on
country)....................................................109Feedback during starting and switching
off...............................................................110Fuel operated heater (depending on
country)....................................................109Parking heater.............................................107Programming the transmitter.....................111Remote start in combination with direct
start or timer.............................................110Remote starting...........................................110
Auxiliary input (AUX IN) socket............125Auxiliary power sockets.......................122
273
Index
BBattery connection points...................205Bluetooth setup....................................232
Handling of phones...................................232Requirements for Bluetooth
connection..............................................232Bonnet lock
See: Opening and closing the bonnet.....188Booster cables
See: Using booster cables.......................204Booster cushions....................................20
Booster cushion...........................................20Booster seat.................................................20Integrated booster cushion.........................21
Brake and clutch fluid check...............198Brakes......................................................141
Principle of operation..................................141Bulb changing
See: Changing a bulb..................................60Bulb specification chart..........................67
CCargo nets..............................................160
Luggage retention net...............................160Car wash
See: Cleaning the exterior........................202Catalytic converter................................134
Driving with a catalytic converter.............134CD changer............................................125Changing a bulb......................................60
Approach lamp.............................................62Central high mounted brake lamp............64Front fog lamps............................................62Headlamp......................................................60Interior lamp..................................................66Luggage compartment lamp.....................67Number plate lamp......................................66Reading lamps..............................................66Rear lamps....................................................63Side repeaters..............................................62Vanity mirror lamp.........................................67
Changing a fuse.....................................175
Changing a road wheel.......................206Installing a road wheel...............................209Jacking and lifting points...........................207Locking wheel nuts...................................206Removing a road wheel............................208Vehicle jack.................................................206Vehicles with a temporary spare
wheel.......................................................206Changing the remote control
battery....................................................32Remote control with a folding key
blade..........................................................32Remote control without a folding key
blade..........................................................33Changing the wiper blades....................51
Rear window wiper blades.........................52Windscreen wiper blades............................51
Checking the wiper blades....................51Child safety...............................................19Child safety locks....................................25Child seat positioning.............................22Child seats................................................19
Child restraints for different massgroups........................................................19
Cigar lighter.............................................121Cleaning the exterior............................202
Body paintwork preservation..................202Cleaning the chrome trim.........................202Cleaning the headlamps...........................202Cleaning the rear window........................202
Cleaning the interior.............................202Instrument cluster screens, LCD screens,
radio screens.........................................203Seat belts....................................................202
Climate control.......................................101Principle of operation..................................101
Climate control commands................254Climate.........................................................254
Clock........................................................121Coded keys.............................................43Cold weather precautions...................170Connecting an external device..........258
Connection.................................................258Connecting an external device -
Vehicles With: Bluetooth...................258Connecting a Bluetooth audio
device......................................................258
274
Index
Connectivity...........................................257General information...................................257
Convenience features...........................121Coolant check
See: Engine coolant check.......................197Cruise control.........................................149
Principle of operation.................................149Cruise control
See: Using cruise control..........................149Cup holders............................................123
DDetachable tow ball..............................166
Driving with a trailer....................................168Driving without a trailer...............................169Inserting the tow ball arm..........................167Maintenance...............................................169Removing the tow ball arm.......................168Unlocking the tow ball arm
mechanism..............................................167Diesel particulate filter (DPF).................131
Regeneration...............................................131Direction indicators.................................58Disabling the passenger airbag............30
Disabling the passenger airbag..................31Enabling the passenger airbag...................31Fitting the passenger airbag deactivation
switch..........................................................31Disarming the alarm................................46
Vehicles with keyless entry.........................46Vehicles without keyless entry...................46
Disarming the engine immobiliser........43Dog guard...............................................162
Installing behind the front seats...............162Installing behind the rear seats.................163
DPFSee: Diesel particulate filter (DPF).............131
Driving hints............................................170Driving through water...........................170
Driving through water ................................170
EElectric exterior mirrors...........................71
Electric folding mirrors.................................72Mirror tilting positions....................................71Reverse mirror dipping................................72
Electric seats...........................................1162-way electric seat......................................1168-way electric seat......................................117
Electric sunroof.......................................111Opening and closing the sunroof.............112Opening and closing the sunroof
automatically............................................113Sunroof anti-trap protection......................113Sunroof relearning.......................................114Sunroof safety mode..................................114Tilting the sunroof........................................113
Electric windows.....................................69Anti-trap function..........................................70Driver’s door switches.................................69Front and rear passengers’ door
switches....................................................69Global opening and global closing............69Opening and closing the windows
automatically.............................................69Resetting the memory of the electric
windows....................................................70Safety mode..................................................70Safety switch for rear windows.................69
Electromagnetic compatibility............269Emergency equipment.........................171Engine compartment overview - 1.6L
Duratec-16V Ti-VCT (Sigma).............189Engine compartment overview - 1.8L
Duratorq-TDCi (Lynx) Diesel.............193Engine compartment overview - 2.0L
Duratec-HE (MI4)................................190Engine compartment overview - 2.0L
Duratorq-TDCi (DW) Diesel...............194Engine compartment overview - 2.2L
Duratorq-TDCi (DW) Diesel...............195Engine compartment overview - 2.3L
Duratec-HE (MI4)................................191Engine compartment overview - 2.5L
Duratec (VI5)........................................192Engine coolant check...........................197
Checking the coolant level........................197Topping up...................................................198
Engine heater.........................................132Engine immobiliser..................................43
Principle of operation...................................43Engine oil check.....................................197
Checking the oil level..................................197Topping up...................................................197
275
Index
Engine oil dipstick - 1.6L Duratec-16VTi-VCT (Sigma)....................................196
Engine oil dipstick - 1.8L Duratorq-TDCi(Lynx) Diesel.........................................196
Engine oil dipstick - 2.0L Duratec-HE(MI4)/2.3L Duratec-HE (MI4)............196
Engine oil dipstick - 2.0L Duratorq-TDCi(DW) Diesel/2.2L Duratorq-TDCi (DW)Diesel.....................................................197
Engine oil dipstick - 2.5L Duratec(VI5).......................................................196
Exterior mirrors.........................................71Manual folding mirrors..................................71
FFastening the seat belts........................29First aid kit................................................171Fog lamp
See: Front fog lamps...................................54Forward alert function..........................155
Adjusting the warning sensitivity..............156Switching forward alert on/off..................156
Front fog lamps.......................................54Fuel and refuelling.................................133
Technical specifications.............................136Fuel burning heater
See: Auxiliary heater...................................107Fuel consumption..................................135Fuel consumption
See: Technical specifications....................136Fuel filler flap...........................................134
Vehicles with diesel engine.......................135Fuel quality - Diesel...............................133
Long-term storage.....................................134Fuel quality - E85...................................133
Long-term storage.....................................133Fuel quality - Petrol................................133Fuse box locations................................173
Central fuse box..........................................173Engine compartment fuse box................173Rear fuse box - 4-door and 5-door.........174Rear fuse box - Estate...............................174
Fuses.......................................................173Fuse specification chart........................176
Central fuse box..........................................179Engine compartment fuse box................176Rear fuse box...............................................181
GGauges.....................................................74
Engine coolant temperature gauge..........75Fuel gauge.....................................................76
GearboxSee: Transmission.......................................138
General driving points - Vehicles With:Sports Suspension..............................170
General information on radiofrequencies............................................32
Getting started......................................266Activating the mobile phone navigation
system.....................................................266Compatibility of phones............................266Installing the micro SD card......................266
Glasses holder.......................................125Global opening and closing...................38
Global closing................................................39Global opening.............................................39
Glove box...............................................123Cooled glove box.......................................123
HHandbrake
See: Parking brake......................................141Hazard warning flashers........................56Headlamp adjustment
See: Adjusting the headlamps - VehiclesWith: Adaptive Front Lighting/XenonHeadlamps................................................55
Headlamp levelling..................................55Recommended headlamp levelling switch
positions....................................................55Headlamp washers.................................51Head restraints.......................................118
Adjusting the head restraint.......................118Removing the head restraint.....................118
Heated seats..........................................119Heated windows and mirrors..............106
Heated exterior mirrors.............................107Heated windows........................................106
HeatingSee: Climate control....................................101
Hill launch assistSee: Using hill start assist..........................143
276
Index
Hill start assist.........................................143Principle of operation.................................143
Hints on driving with ABS......................141HLA
See: Hill start assist.....................................143See: Using hill start assist..........................143
IIgnition switch.........................................127Immobiliser
See: Engine immobiliser..............................43Information displays................................79
General information.....................................79Information messages...........................92
Active suspension........................................93Alarm..............................................................93Battery and charging system.....................94Climate control.............................................94Cruise control and Adaptive cruise control
(ACC).........................................................94Doors open...................................................95Engine immobiliser.......................................95Hill launch assist (HLA).................................95Keyless system............................................96Lighting...........................................................96Maintenance.................................................97Message indicator.......................................92Message symbols........................................92Occupant protection...................................97Parking brake................................................97Power steering.............................................98Stability control (ESP)...................................98Transmission.................................................98Tyre pressure monitoring system.............98Viewing current messages.........................92Voice control................................................100
Inspecting safety systemcomponents........................................172Seat belts.....................................................172
Instrument lighting dimmer...................121Instruments..............................................74Interior lamps...........................................58
Courtesy lamp..............................................58Reading lamps..............................................58Vanity mirror lamps......................................59
Introduction................................................7
ISOFIX anchor points..............................24Attaching a child seat with top
tethers........................................................24Top tether anchor points............................24
JJump starting
See: Using booster cables.......................204
KKeyless entry...........................................40
Disabled keys................................................42General information.....................................40Locking and unlocking the doors with the
key blade...................................................42Locking the vehicle......................................40Passive key...................................................40Unlocking the vehicle...................................41
Keyless starting......................................127Failure to start..............................................128Ignition on.....................................................127Starting a diesel engine.............................128Starting with automatic transmission......128Starting with manual transmission...........128Stopping the engine...................................129
Keys and remote controls.....................32
LLighting control........................................53
Headlamp flasher.........................................53Home safe lighting.......................................54Lighting control positions............................53Main and dipped beam...............................53Parking lamps...............................................53
Lighting.....................................................53Load carriers
See: Roof racks and load carriers............162Load carrying.........................................157
General information....................................157Load retaining fixtures..........................164
Installing the load bracket.........................164Installing the load retaining fixtures..........164
277
Index
Locking and unlocking...........................36Automatic relocking.....................................38Central locking..............................................36Double locking..............................................36Double locking the doors with the
key..............................................................36Locking and unlocking confirmation.........36Locking and unlocking the doors and the
luggage compartment lid with theremote control..........................................37
Locking and unlocking the doors frominside..........................................................37
Locking and unlocking the doors with thekey..............................................................36
Luggage compartment lid..........................38Reprogramming the unlocking
function......................................................38Locks.........................................................36Luggage anchor points........................157
4-door and 5-door.....................................158Estate............................................................157
Luggage covers.....................................161
MMaintenance...........................................187
General information....................................187Technical specifications.............................199
Manual climate control.........................102Air conditioning............................................103Air distribution control................................102Blower..........................................................102Heating the interior quickly........................102Recirculated air...........................................102Ventilation.....................................................103
Manual seats...........................................115Adjusting the angle of the seatback........116Adjusting the height of the driver’s
seat............................................................116Adjusting the lumbar support....................116Moving the seats backwards and
forwards....................................................115Manual transmission.............................138
All vehicles....................................................138Selecting reverse gear...............................138
Map pockets..........................................124
Memory function...................................124Recalling a stored seat position...............125Setting a memory pre-set.........................124
Message centreSee: Information displays............................79
MirrorsSee: Heated windows and mirrors..........106See: Windows and mirrors.........................69
NNavigation introduction........................265Navigation system commands..........254Navigation system................................266
OOccupant protection..............................27
Principle of operation...................................27Oil check
See: Engine oil check.................................197
See: Opening and closing the bonnet.....188
OOpening and closing the bonnet........188
Closing the bonnet.....................................188Opening the bonnet...................................188
PParking aid..............................................147
Principle of operation.................................147Parking aid
See: Using the parking aid.........................147Parking brake..........................................141
Applying the parking brake........................141Parking on a hill............................................141Releasing the parking brake......................141
Parts and accessories..............................7Look for the Ford logo on the following
parts .............................................................8Now you can be sure that your Ford parts
are Ford parts..............................................7
278
Index
Personalised settings.............................90Help screen, radio, navigation and phone
information................................................90Language.......................................................91Navigation information................................90Units of measure...........................................91
Power steering fluid check..................198Topping up...................................................198
Programming the remote control........32Programming a new remote control........32Reprogramming the unlocking
function......................................................32
QQuick start.................................................10
Adjusting the steering wheel.......................13Autolamps......................................................14Automatic climate control...........................15Automatic transmission................................17Autowipers.....................................................14Diesel particulate filter (DPF).......................16Electric folding mirrors..................................14Engine idle speed after starting..................16Fuel filler flap...................................................16Information displays......................................15Instrument panel overview - left-hand
drive............................................................10Instrument panel overview - right-hand
drive.............................................................11Keyless entry.................................................12Keyless starting.............................................16Manual climate control.................................15Manual transmission.....................................17Memory function...........................................15
RRear fog lamps........................................54Rear seats...............................................118
Creating a level load floor...........................118Folding the seatbacks down.....................118Folding the seatbacks up...........................119
Rear under floor storage......................160Vehicles with a sliding loadspace
floor...........................................................160Vehicles without a sliding loadspace
floor...........................................................160
Rear window wiper and washers.........50Intermittent wipe..........................................50Reverse gear wipe.......................................50Washer...........................................................50
Refuelling - E85......................................135Refuelling................................................135Remote control battery
See: Changing the remote controlbattery........................................................32
Remote control programmingSee: Programming the remote control.....32
Removing a headlamp...........................59Repairing minor paint damage...........203Road Safety...........................................265
Safety information......................................265Roof racks and load carriers...............162
Roof rack......................................................162Run flat tyres..........................................216
Principle of operation.................................216Replacing run flat tyres..............................216What to do if a run flat tyre has a
puncture..................................................216Running-in...............................................170
Brakes and clutch.......................................170Engine...........................................................170Tyres..............................................................170
SSeat belt height adjustment..................29Seat belt reminder..................................30
Deactivating the seat belt reminder..........30Seats........................................................115Sitting in the correct position................115Sliding loadspace floor..........................158
Storage compartment...............................159Snow chains
See: Using snow chains.............................217Speed control
See: Cruise control.....................................149Stability control.......................................142
Principle of operation.................................142Stability control
See: Using stability control........................142Starter switch
See: Ignition switch.....................................127Starting a diesel engine.........................131
Cold or hot engine......................................131
279
Index
Starting a petrol engine - E85.............130Starting at low ambient temperatures
...................................................................130Starting a petrol engine........................129
Cold or hot engine......................................129Engine idle speed after starting...............130Flooded engine...........................................130
Starting the engine................................127General information....................................127
Status after a collision...........................172Steering wheel lock...............................129
Vehicles with keyless starting...................129Vehicles without keyless starting.............129
Steering wheel.........................................47Storage compartments........................123Sun blinds................................................121Sunroof
See: Electric sunroof....................................111Switching off the engine.......................132
Vehicles with a turbocharger....................132Symbols glossary.......................................7
Symbols in this handbook.............................7Symbols on your vehicle................................7
TTechnical specifications.......................223
Technical specifications............................223Telephone commands........................250
Create a phonebook.................................250Main settings..............................................254Phone..........................................................250Phone functions.........................................252
Telephone controls..............................233Remote control..........................................233
Telephone setup...................................231Bond another Bluetooth phone..............232Making a phone an active phone...........232Phonebook..................................................231Phonebook categories..............................231
Telephone...............................................231General information....................................231
TelephoneSee: Using the telephone - Vehicles With:
Navigation System................................236See: Using the telephone - Vehicles Without:
Navigation System................................233
Towing a trailer.......................................166Steep gradients..........................................166
Towing points.........................................185Towing the vehicle on four
wheels..................................................185All vehicles....................................................185Vehicles with automatic
transmission............................................185Towing.....................................................166Transmission..........................................138Trip computer..........................................88
Average fuel consumption.........................88Average speed.............................................88Distance to empty........................................88Odometer......................................................88Outside air temperature..............................88Tripmeter.......................................................88Type 1 and 2..................................................89Type 3............................................................89
Type approvals......................................268FCC/INDUSTRY CANADA NOTICE.........268RX-42 - declaration of conformity..........268
Tyre care.................................................217Tyre pressure monitoring system.......218
Checking the tyre pressures....................218Setting the vehicle load.............................218
Tyre pressuresSee: Technical specifications....................219
Tyre repair kit..........................................210Checking the tyre pressure......................215General information....................................210Inflating the tyre...........................................211Using the tyre repair kit...............................211
TyresSee: Wheels and tyres..............................206
UUSB port.................................................126Using ACC..............................................152
Automatic deactivation..............................154Cancelling ACC...........................................154Changing the set speed............................153Resuming ACC...........................................154Setting a speed...........................................153Setting the vehicle gap..............................153Switching ACC off.......................................154Switching ACC on.......................................153
280
Index
Using active suspension......................146Selecting a setting......................................146System malfunction...................................146
Using an iPod.........................................261CD Navigation units...................................263DVD Navigation units.................................263Sony radio...................................................262
Using a USB device..............................259CD Navigation units...................................260DVD Navigation units..................................261Sony radio...................................................259
Using booster cables...........................204To connect the booster cables...............204To start the engine.....................................204
Using cruise control..............................149Cancelling the set speed..........................149Changing the set speed............................149Resuming the set speed...........................150Setting a speed...........................................149Switching cruise control off.......................150Switching cruise control on.......................149
Using hill start assist..............................143Activating the system................................144Deactivating the system............................145
Using seat belts during pregnancy......30Using snow chains................................217Using stability control............................142Using the parking aid............................147
Manoeuvring with the parking aid............147Switching the parking aid on and off.......147
Using the telephone - Vehicles With:Navigation System.............................236Changing the active phone......................237Debonding a bonded phone...................237Making a call...............................................236Muting the microphone............................236Receiving an incoming call.......................236Receiving a second incoming call...........236
Using the telephone - Vehicles Without:Navigation System.............................233Changing the active phone......................235Debonding a bonded phone...................235Debonding a bonded phone - Sony
radio.........................................................235Making a call...............................................233Muting the microphone............................235Receiving an incoming call.......................234Receiving a second incoming call...........234
Using voice control...............................238Name tag....................................................239System operation......................................238
Using winter tyres..................................217
VVehicle battery......................................204Vehicle care...........................................202Vehicle identification number
(VIN)......................................................222Vehicle identification plate...................222Vehicle identification.............................222Vehicle recovery....................................185Ventilated seats......................................119Ventilation
See: Climate control....................................101Vents
See: Air vents...............................................101VIN
See: Vehicle identification number(VIN).........................................................222
Voice control.........................................238Principle of operation................................238
WWarning lamps and indicators...............76
ABS warning lamp........................................76Airbag warning lamp....................................76Brake system lamp......................................76Cruise control indicator...............................76Direction indicators.......................................76Engine warning lamp...................................76Forward alert indicator.................................77Front fog lamp indicator..............................77Frost warning lamp.......................................77Glow plug indicator.......................................77Headlamp indicator......................................77Ignition warning lamp...................................77Low fuel level warning lamp........................77Main beam indicator.....................................77Message indicator........................................77Oil pressure warning lamp...........................77Rear fog lamp indicator...............................78Seat belt reminder........................................78Shift indicator.................................................78Stability control (ESP) warning lamp..........78
281
Index
Warning triangle......................................1714-door and 5-door......................................171Estate and vehicles with tyre repair
kit................................................................171Washer fluid check................................199Washers
See: Wipers and washers...........................49Washing
See: Cleaning the exterior........................202Wheels and tyres..................................206
General information...................................206Technical specifications.............................219
Windows and mirrors.............................69Windscreen washers.............................50Windscreen wipers.................................49
Intermittent wipe..........................................49Winter tyres
See: Using winter tyres..............................217Wipers and washers...............................49
282
Index
Feel the difference
9S7J-19A321-DA(C
G3536en)