2005-01-2495
Transcript of 2005-01-2495
-
8/10/2019 2005-01-2495
1/13
400 Commonwealth Drive, Warrendale, PA 15096-0001 U.S.A. Tel: (724) 776-4841 Fax: (724) 776-5760 Web: www.sae.or
SAE TECHNICAL
PAPER SERIES
2005-01-2495
On Predicting Aeroacoustic Performance of
Ducts with Broadband Noise Source Models
Ashok D. Khondge, Sandeep D. Sovani and Sung-Eun KimFluent Inc
Steven C. Guzy and Ashraf A. FaragDelphi Thermal and Interio
SAE 2005 Noise and VibrationConference and Exhibition
Traverse City, MichiganMay 16-19, 2005
-
8/10/2019 2005-01-2495
2/13
The Engineering Meetings Board has approved this paper for publication. It has successfully completed
SAE's peer review process under the supervision of the session organizer. This process requires aminimum of three (3) reviews by qualified reviewers.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of SAE.
For permission and licensing requests contact:
SAE Permissions
400 Commonwealth DriveWarrendale, PA 15096-0001-USA
Email: [email protected]: 724-772-4891
Tel: 724-772-4028
For multiple print copies contact:
SAE Customer ServiceTel: 877-606-7323 (inside USA and Canada)
Tel: 724-776-4970 (outside USA)Fax: 724-776-1615
Email: [email protected]
ISSN 0148-7191
Copyright 2005 SAE International
Positions and opinions advanced in this paper are those of the author(s) and not necessarily those of SAE.The author is solely responsible for the content of the paper. A process is available by which discussionswill be printed with the paper if it is published in SAE Transactions.
Persons wishing to submit papers to be considered for presentation or publication by SAE should send the
manuscript or a 300 word abstract of a proposed manuscript to: Secretary, Engineering Meetings Board, SAE.
Printed in USA
-
8/10/2019 2005-01-2495
3/13
Copyright 2005 SAE International
ABSTRACT
A numerical method of predicting aeroacousticperformance of HVAC ducts is presented here. Themethod comprises of two steps. First, the steady stateflow structure inside a duct is simulated usingcomputational fluid dynamics (CFD). A k-epsilon basedturbulence model is used. In the second step broadbandnoise source models are used to estimate the soundpower generation within the duct. In particular, modelsestimating dipole and quadrupole sound sourcestrengths are studied.
A baseline generic duct geometry was studied with 3additional design variations. The loudness rankings ofthese three designs were determined numerically.Simultaneously, the sound generated by these threedesigns was measured on a flow bench with amicrophone kept downstream of the duct outlet. Thenumerically predicted loudness rankings were comparedwith experimentally determined rankings and the two arefound to be in agreement, thus validating the numericalmethod.
INTRODUCTION
Noise generated in automotive HVAC ducts can often bevery loud and cause discomfort and distraction to thedriver and passengers. HVAC system manufacturerstherefore take significant efforts to optimize noisegenerated by ducts. To-date these efforts mostlycomprise of expensive experimental noise testing due tothe lack of practically usable numerical methods that canpredict aerodynamically generated noise in ducts. It ishighly desirable to have numerical methods of predictingduct acoustic performance for many reasons. First,numerical analysis is often quite inexpensive comparedto experimental testing. Moreover, numerical analysiscan be done in the early stages of the design process to
provide design direction even before prototypes are builtAlso, numerical analysis easily provides much greateinsight into the physics involved compared toexperimental measurement.
Numerical simulation of duct noise has received attentionfrom researchers
1, 2, 3, 4. Though these works provide
excellent methods of computing sound propagation, theylack detailed calculations of sound generation.
To determine the loudness of a duct, it is essential toaccurately simulate sound sources. Automotive HVACduct noise is almost exclusively aerodynamic noise, i.e
noise generated by fluid flow. It is typically caused by twoaspects, one, the rotating blades of the blower, and twogeometric complexities in the duct. Both these cause theflow to be unsteady and turbulent and generate noise.
There are four primary approaches of numericallymodeling aeroacoustic phenomena. In order odecreasing computational effort, these are (a)computational aeroacoustics (CAA)
5, 6, 7, 8, 9, 10, (b) the
coupling of CFD and a sound propagation solver11, 12
, (cintegral sound propagation models
13, 14, 15 and (d)
broadband noise source models. Details of theseapproaches are presented in other articles
11, 12, along
with examples5, 6, 7, 8, 9, 10, 13, 14, 15
.
Of these, the first three methods require well-resolvedtransient CFD simulations, since they aim to determinethe actual time-varying sound-pressure signal at thereceiver, and from that, the sound spectrum. In severapractical engineering situations, only the locations andrelative strengths of sound sources need to bedetermined rather than the sound spectra at thereceivers. If the sound is broadband (i.e. lacking anyprominent tones characterized by sharp peaks in thespectrum), the source strengths can be evaluated with
* Corresponding Author
2005-01-2495
On Predicting Aeroacoustic Performance of Ducts
with Broadband Noise Source Models
Ashok D. Khondge, Sandeep D. Sovani* and Sung-Eun Kim
Fluent Inc
Steven C. Guzy and Ashraf A. FaragDelphi Thermal and Interior
-
8/10/2019 2005-01-2495
4/13
reasonable accuracy from the time-averaged structure ofthe turbulent flow in the source regions.
Turbulence is the primary cause of sound inaeroacoustics, so in a broad sense, regions of the flowfield where turbulence is strong produce louder sourcesof sound. A number of analytical models referred to asbroadband noise source models synthesize sound atpoints in the flow field from local flow and turbulencequantities and estimate local sound source strengths.The key advantage of these models is that they requirevery modest computational resources compared to theother three methods. Broadband noise models only needa steady state flow solution, whereas the other methodsrequire well-resolved transient flow solutions. However,the drawback of the broadband noise source models isthat they are not able to predict sound spectra at receiverlocations. They can only qualitatively indicate whichsound sources are stronger than others.
One important practical aspect where broadband noisesource models can be used is in determining loudnessrankings of different design variations of an object. In the
present work two broadband noise models are used todetermine loudness rankings of five different ductdesigns. The computationally predicted noise rankingsare compared with experimentally measured rankings.
PROBLEM STATEMENT
The aim of the present study was to determine whetherbroadband noise models have the ability to correctlypredict loudness rankings of automotive HVACducts/modules. For this a generic duct design, whichcontains some of the basic characteristics of HVACmodule, is considered with two additional design
variations. The baseline design is presented in Figure 1.
The duct design is purposely kept generic so that it canbe widely used as a benchmark in the future. Threeimportant features prominently found in actuaautomotive HVAC ducts/modules are included in thisdesign. They are, a sudden expansion (accompanied bya change in cross-section shape from round torectangular), a bend, and a side cavity. Dimensionadetails of the baseline duct are shown in Figure 2.
The baseline duct is referred to as Design1 henceforward. Designs 2, 3, and 4 are exactly same as Design1, except they have a baffle immediately upstream of thecavity. In Designs 2, 3, and 4 the baffle height is 0.03 m0.07 m, and 0.11 m respectively. In all designs the baffle
Inlet
Outlet
Figure 1.Baseline duct geometry.
0.155
0.200
0.250
Figure 2. Dimensional details of the baseline duct (Design1). All dimensions are in meters.
0.200 0.150
0.150
0.050 0.100
0.100
0.100
0.200
-
8/10/2019 2005-01-2495
5/13
(a) Design2
(b) Design3
(c) Design4Figure 3.Cross-sections of the different designs.
Dimensions are in meters.
is 0.0016 m thick. See Figure 3 for cross-sections of
Designs 2 through 4.Noise rankings of these ductdesigns are calculated by conducting numericalsimulations and are compared with experimentallymeasured rankings to determine if the broadband noisemodels studied predict noise rankings accurately.
NUMERICAL METHOD
The numerical simulation method comprises of twosteps. First, a steady state CFD simulation of flowpassing through the duct is conducted. In the secondstage, the broadband noise models are used to estimate
acoustic source power from the results of the CFDsimulation. Both these steps are conducted with thecommercial CFD code FLUENT 6.2.16
16.
COMPUTATIONAL DOMAIN AND MESH
The computational domain comprises of the duct and alarge plenum at its outlet that represents the openatmosphere.
Various views of the mesh cross-section along thebaseline ducts center plane are shown in Figure 4. Thevolume mesh was composed of a total of 2 millionexclusively hexahedral cells. A fine mesh resolution ismaintained in regions where high gradients areexpected, such as the region in close proximity of theduct walls and the shear regions in the suddenexpansion and in the cavity mouth. The mesh wascreated using the commercial meshing software packageGAMBIT2.1
17
SOLVER SETTINGS, TURBULENCE MODEL, ANDBOUNDARY CONDITIONS
The commercial CFD code FLUENT6.2.1616
used toconduct the simulations is based on the finite volumemethod and provides a choice of solvers and solvesettings. The settings chosen for this study are listed inTable 1.
Turbulence was modeled using RNG (Renormalization
Group Theory) k- model. In this model the turbulentviscosity is computed using the relation,
2k
Ct = (1
where the value of the constant C is derived to be0.0845 from RNG theory. Non-equilibrium wall functionsare used. These functions are similar to those proposedby Launder and Spalding
18but the log-law is sensitized
to pressure-gradient19
. Further details are seen inFLUENT documentation
16.
The boundary conditions used in the simulation are listedin Table 2. A constant velocity boundary condition waschosen for the inlet corresponding to a 300 cfm flow rateof air which is typical of an automotive climate controsystem. Since we assume the flow to be incompressiblean arbitrary value of pressure can be assigned to the
pressure outlet without any effect on the flow field, so it iskept at 0 Pa (gage). The boundaries of the duct and theplenum were kept as no-slip walls while the duct outletwas kept as an interior so air can pass freely from theduct into the plenum.
BROADBAND NOISE SOURCE MODELS
Two broadband noise source models are considered inthis work, a model estimating the contribution ofquadrupole (volume) sources and the other indicating the
0.03
0.11
0.07
Inlet
Outlet
Cavity
Baffle
SuddenExpansion
-
8/10/2019 2005-01-2495
6/13
(a) Entire computational domain.
(b) Mesh in the duct.
(c) Mesh in the sudden expansion.
(d) Mesh in the cavity mouth.Figure 4.View of the central cross section of the
baseline case mesh.
Table 1. Solver settings used in the simulations.
Function Setting
Solver
Precision
Pressure discretization
Momentum discretization
Pressure-velocity coupling
Fluid
Steady state,Segregated ImplicitDouble Precision2
ndorder
2nd
order upwindSIMPLEC
Air (incompressible)
Table 2. Boundary conditions
Boundary Boundary Condition Value
Duct Inlet
Duct Outlet
Duct boundaries
Plenum Outlet
Plenum boundaries
Constant Velocity
Interior
No slip wall
Constant Pressure
No slip wall
7.507 m/s
(=300 cfm)
0 Pa (gage)
contribution of dipole (surface) sources. Both have theirfoundation in Lighthills acoustic formulation. Lighthill
20
showed that at distances large compared with thedimension of the flow, the density fluctuation due tosound wave can be computed from:
(2)
where Tijis Lighthills stress tensor defined by
(3)
where ijis the viscous tensor.
Quadrupole Source Model
Proudman21
, based on Lighthills acoustic analogyoriginally derived a formula for acoustic power generatedby isotropic turbulence without mean flow. More recentlyLilly
22 re-derived the formula by accounting for the
retarded time difference which was neglected inProumans original derivation. Both derivations yieldacoustic power due to unit volume of isotropic turbulence
as:
(4)
where uand are turbulence velocity and length scalesrespectively, and a0is the speed of sound. The value of
the numerical constant in eqn. (4) varies depending onthe specific methods of derivation. In Proudmans
original derivation, 13. Lilly found 10.96. In terms
-
8/10/2019 2005-01-2495
7/13
of k and and using u2 = 2k/3, = 1.5u3/l and Mt =
0/2 ak , eqn. (4) can be written as:
(5)
The rescaled constant , is approximately 0.5 for the
Proudmans constant ( 13). Sarkar and Hussaini23
,based on their DNS (Direct Numerical Simulation) for
isotropic turbulence, found that = 0.1 best fits the DNSdata. FLUENT adopts = 0.1. Eqn. 5 thus provides thelocal sound power contribution per unit volume due toisotropic turbulence (quadrupole sound source) at everypoint in the computational domain.
Dipole Source Model
Far-field sound generated by turbulent boundary layerflow over a solid body at low Mach numbers is often ofpractical interest. The Curle's integral
24 based on
acoustic analogy can be used to approximate the localcontribution from the body surface to the total acoustic
power. To that end, one can start with the Curle's:
(6)
where denotes the emission time ( = t - r/a0), and Stheintegration surface.
Using this, the sound intensity in the far field can then beapproximated by,
(7)
where Acis the correlation area, , and cosis
the angle between and the wall-normal direction. The total acoustic power emitted from the entire body
surface can be computed from
(8)
where
(9)
which can be interpreted as the local contribution per unitsurface area of the body surface to the total acousticpower. The mean-square time-derivative of the surfacepressure and the correlation area are further
approximated in terms of turbulent quantities liketurbulent kinetic energy, dissipation rate, and wall-shear.
FLUENT reports the acoustic surface power defined byEquation (9) both in physical (W/m
2) and dB units.
SIMULATION PROCEDURE
A steady state CFD simulation was conducted for eachdesign. The solution was initially converged with firstorder discretization schemes and finally with secondorder schemes. After obtaining converged CFDsolutions, acoustic post-processing was done with thebroadband noise source models. This included twocalculations. The first was calculation of the volumeintegral of PA from Eqn. (5) on the volume containedinside the duct. Here, PA is an estimate of the locaquadrupole acoustic power contribution per unit volumeTherefore the volume integral of PA is indicative of thetotal acoustic power emitted by the entire duct due toquadrupole sources. The second was a calculation of thesurface integral of I from Eqn. (9) on all internal wal
surfaces of the duct. Here, I is an estimate of the locadipole acoustic power contribution per unit areaTherefore, the surface integral of Ion all inner surfacesof the duct is indicative of the total acoustic poweemitted by the duct due to dipole sources.
RESULTS
FLOWFIELD STRUCTURE
All designs were experimentally tested as well assimulated at a flow rate of 300 cfm corresponding to aninlet velocity of 7.507 m/s. Flow structure for the baseline
geometry is presented in Figure 5 via contour plots ovelocity magnitude, pressure, turbulent kinetic energyand dissipation rate. Velocity contours show that the flowenters the duct at a constant velocity and forms aboundary layer on the circular pipe section immediatelydownstream of the inlet. Upon encountering the suddenexpansion further downstream, the flow separates fromthe walls and forms a jet. The boundaries of the jet donot reattach with the walls until the jet enters the 90degree turn and impinges on the far wall. The bend turnsthe flow vertically upward and flattens the jet into athinner, high velocity jet with a large separated region toits left. The jet forms a shear layer in the cavity mouth
and creates a rotational flow inside the cavity.
Wherever the velocity gradient is large, high values ofturbulent kinetic energy are seen to occur in the contouplot of turbulent kinetic energy. Locations of highturbulence include the region downstream of the suddenexpansion as well as on the outer (left) boundary of thehigh velocity jet in the vertical section of the duct. Theseregions of high turbulence are expected to be strongsources of noise.
The flow structure in the other 3 designs is presented inFigure 6 using velocity contour plots. The 0.03 m baffle
-
8/10/2019 2005-01-2495
8/13
at the leading edge of the cavity in Design 2 lifts thevertical jet off from the cavity mouth. As a result therotation in the cavity of Design 2 is much milder than thatin the baseline case. The vertical jet also becomesthinner and faster than in the baseline case. When thebaffle height is increased to 0.07 m in Design 3 the jetvelocity increases further and a strong separation regionis seen behind the baffle. In Design 4 where the baffleheight is increased to 0.11 m, there is only a smallopening left for the flow and the vertical jet has a even
higher velocity. The separation region behind the baffle isfurther pronounced.
NOISE CHARACTERISTICS
As the vertical jet becomes progressively faster fromDesign1 through 4 and the separation region behind thebaffle becomes more pronounced, it is expected that theoverall turbulence in the flow field will increase causingan increase in the broadband noise level. Experimentalmeasurements confirm this trend. Figure 7 shows thesound spectra measured at a point 1 m directlydownstream of the centroid point of the duct outlet. The
spectra extend from 20 to 20,000 Hz. Over most of thisextent the SPL for all four ducts is the same, except inthe region from about 150 to 400 Hz. Therefore, theperceived difference in loudness of these ducts arisesfrom this frequency band. Here, Design 2 is seen to belouder than Design 1 by roughly 2 to 3 dBA. Design 3 islouder than Design 2 by about 3 to 4 dBA, and likewiseDesign 4 is louder than Design 3 by 3 to 4 dBA.
Sound power estimates made using broadband noisesource models in the CFD simulations are shown inTable 3. Both the dipole source power as well as thequadrupole source power are seen to increase from
Design 1 through 4.
In conclusion, the two broadband noise source modelsconsidered here correctly predict the same noise rankingbetween the 4 designs studied as observed inexperiments.
Table 3. Acoustic power generated inside the ductas estimated from the simulations.
Design QuadrupoleSource Power in
Watts
Volume Integral ofPAin Eqn. (5)
DipoleSource Power in
Watts
Surface Integral of IinEqn. (9)
Design1 7.31e-13 2.44e-09
Design2 1.63e-12 3.56e-09
Design3 9.48e-12 8.64e-09
Design4 2.94e-10 1.24e-07
CONCLUSION
Broadband noise source models are an attractive optionto quickly and inexpensively evaluate the acousticperformance of devices. Broadband noise modelsrequire inexpensive steady state simulations to estimatenoise where as other methods such as computationaaeroacoustics and integral sound propagation methodsrequire expensive transient simulation. Howeverbroadband noise source models cannot provide accuratesound spectra unlike the other methods.
One possible practical use of the broadband noisesource models is studied in this paper. The broadbandnoise models have been used to determine the noiseloudness rankings of a generic HVAC duct with 4 designvariations. The rankings are computed with a dipole anda quadrupole source power model. The computedrankings are compared to experimentally determinedrankings and the two are found to be in excellenagreement. In conclusion, the broadband noise modelsare a valuable and relatively inexpensive practical tool fodetermining noise loudness rankings of HVAC duc
designs.
REFERENCES
1. Reichert R.S. and Birigen S., Time domain
simulation of acoustic propagation in lined duct,Applied Acoustics, vol. 62, pp. 1049-1068 (2001)
2. Joseph P., Morfey C.L., and Lowis C.R., Multi-mode
sound transmission in ducts with flow, Journal oSound and Vibration, vol. 264, pp. 523-544 (2003)
3. Ju H. and Fung K.-Y., A time domain method foduct acoustics, Journal of Sound and Vibration, vol
237(4), pp. 667-681 (2000)4. Boudoy M. and Martin V., Prediction of acoustic
fields radiated into a damped cavity by an N-portsource through ducts, Journal of Sound andVibration, vol. 264, pp. 499-521 (2003)
5. Ambs R., Ayar A., Capellmann, C. and Matthes M.Computational aeroacoustics and the developmen
of climate control systems, VDI-Berichte Nr. 18462004
6. Hendriana, D., Sovani, S.D., and Schiemann M.K.On simulating passenger car side windowbuffeting, Society of Automotive Engineers
International, Paper 2003-01-1316 (2003)
7. An, C.-F., Alaie, S.M., Sovani, S.D., Scislowicz M.Singh, K., Side window buffeting characteristics of aSUV, Vehicle Aerodynamics, Vol. SP1874, pp. 43 -
53, SAE International Paper 2004-01-0230 (2004)8. Sovani, S.D. and Hendriana, D, Predicting
passenger car side window buffeting with transient
external aerodynamics simulations, Tenth annuaconference of the CFD society of Canada, June 9-
11, 2002, Windsor, Canada. (2002)9. Sovani, S.D., Reducing wind fatigue and summe
headaches, Desktop Engineering, Dec. (2004)
-
8/10/2019 2005-01-2495
9/13
10. Kannan, V., Sovani, S.D., Greeley, D., and Khondge,A.D., Computational Aeroacoustics Simulation of
Whistle Noise in an Automotive Air-Intake System,submitted to SAENVH conference(2005)
11. Seibert W., Elhen M., Sovani S.D., Simulation of
transient aerodynamics - Predicting buffeting, roaringand whistling using CFD, Sixth Motor Industries
Research Association (MIRA) International VehicleAerodynamics Conference, October 13-14, 2004,
Warwick, U.K.12. Sovani, S.D., Leading Edge Aeroacoustics
Simulation, Fluent News, Vol. 13, no. 2, pp 30-31
(2004)13. Kim, S.-E., Dai, Y., Koutsavdis, K., Sovani, S.D.,
Kadam, N.A., and Ravuri, K.M.R., A versatileimplementation of acoustic analogy based noise
prediction method in a general-purpose CFD code,American Institute of Aeronautics and Astronautics,Paper no. 2003-3202 (2003)
14. Lokhande, B.S., Sovani, S.D., and Xu, J.,Computational aeroacoustic analysis of a generic
side view mirror, Transactions of the SAE: Journal
of Passenger Cars - Mechanical Systems, pp. 2175-2184, SAE Paper 2003-01-1698 (2003)
15. Sovani, S.D. and Chen, K.-H., Aeroacoustics of anAutomotive A-Pillar Raingutter: A Numerical Study
with the Ffowcs-Williams Hawkings Method,submitted to SAE-NVH conference (2005)
16. Fluent 6.2 Users Guide, Fluent Inc., Lebanon NH(2005)
17. Gambit 2.1 Users Guide, Fluent Inc., Lebanon NH(2003)
18. Launder, B.E. and Spalding, D.B., The numericacomputation of turbulent flows, Computer Methods
in Applied Mechanics and Engineering, Vol. 3, pp269-289 (1974)
19. Kim, S.-E. and Choudhury, D., A near-wal
treatment using wall functions sensitized to pressuregradient, in Separated and Complex Flows, ASME
FED, Vol. 217 (1995)20. Lighthill M.J., On sound generated aerodynamically
I General theory, Proceedings of the RoyaSociety A, vol. 211, pp. 564 (1952)
21. Proudman I., The generation of noise by isotropic
turbulence, Proceedings of the Royal Society A, vol214, pp. 219 (1952)
22. Lilly G.M., The radiated noise from isotropicturbulence revisited, NASA Contract Report No. 93-
75, NASA Langley Research Center, Hampton, VA24681 (1993)
23. Sarkar S. and Hussaini M.Y., Computation of the
sound generated by isotropic turbulence, NASAContract Report No. 93-74, NASA Langley Research
Center, Hampton, VA 24681 (1993)
24. Curle N., The influence of solid boundaries onaerodynamical sound, Proceedings of the RoyaSociety A, vol. 2314, pp. 505-514 (1955)
CONTACT
Sandeep Sovani, Ph.D.,Senior Consulting Engineer, Fluent Inc.,220 E. Huron St. Suite 470, Ann Arbor MI [email protected]: 734-213-6821 x235 FAX: 734-213-0147
-
8/10/2019 2005-01-2495
10/13
(a) Velocity magnitude (m/s)
(b) Static pressure (Pa)Figure 5.Contour plots on the central cross-section showing flow structure in the baseline design.
FLOW FEATURES
Vertical Separation Region
Vertical Jet Rotational Flow in Cavity
Shear Layer
Jet Impingement
Horizontal Separation Region
Horizontal Jet
Boundary Layer
-
8/10/2019 2005-01-2495
11/13
(c) Turbulent kinetic energy (m2/s
2)
(d) Turbulence dissipation rate (m2/s
3)
Figure 5.Contour plots on the central cross-section showing flow structure in the baseline design.
-
8/10/2019 2005-01-2495
12/13
Figure 6. Velocity magnitude contours on the central cross section for different designs.
(a) Design 2
(b) Design 3
-
8/10/2019 2005-01-2495
13/13
Figure 7. Experimentally measured sound spectra at a point 1m directly downstream of the centroid of the duct outlet.
(c) Design 4
Figure 6. Velocity magnitude contours on the central cross section for different designs.