2-Way Wireless Security Suite GS2065/TL265GS Product Technical Training (International version)

2-Way Wireless Security Suite

GS2065/TL265GS Product Technical Training(International version)


GS2065/TL265GS– Product Overview


GS2065

GS2065 GSM/GPRS Wireless Alarm Communicator

Overview:The GS2065 provides primary or backup GSM/GPRS communication for the Alexor 2-way wireless security suite

Specifications:• Dimensions : 3.937"x5.875"x0.625" (100mmx150mmx15mm)• Weight : 68 g• Antenna Gain : 2db• Input Voltage : 11.1 to 12.6 V (from the PC-Link header)• Current Draw : 65 mA at 12V (400 mA during the GSM transmission)• Operating Environment : 5 º C to 40º C

(40º F to 104º F)


GS2065


Features:• Back up and primary GSM/GPRS alarm communication• Panel remote uploading/downloading support via GSM/GPRS • Advanced remote and local programming via DLS IV• Keypad programming through WT5500 wireless keypad• Individual Periodic Test Transmission via GSM/GPRS• Supervision heartbeats via GSM/GPRS• 128-bit AES encryption over GSM/GPRS• Full event reporting• Installer code• SIA format• PC-Link connection• Signal strength and trouble display• Optional Network Lock and SIM Lock• PC9155 replacement front plate (8 LEDs) included • Quad-Band: 850 MHz, 1900 MHz, 900 MHz and 1800 MHz


GS2065


Compatible Receivers:Sur-Gard System I Receiver: version 1.10 and higherSur-Gard System II Receiver: version 2.00 and higherSur-Gard SG-DRL3-IP: version 2.20 and higher (for Sur-Gard System III Receiver)

Compatible Control Panel:PC9155 Alexor Wireless Panel version 1.0 and higher

Product Model and Accessories:GS2065GS: For international marketGS-15ANTQ: Antenna Extension Kits with 15 feet cable GS-25ANTQ: Antenna Extension Kits with 25 feet cableGS-50ANTQ: Antenna Extension Kits with 50 feet cablePCLINK-5WP: PCLINK Kits for the programming with DLS IV


TL265GS

TL265GS Internet and GSM/GPRS Dual-Path Alarm Communicator

Overview:The TL265GS is an Internet and GSM/GPRS Dual-Path alarm communicator for the Alexor 2-way wireless security suite

Specifications:• Dimensions : 3.937"x5.875"x0.625" (100mmx150mmx18mm)• Weight : 78 g• Antenna Gain : 2db• Input Voltage : 11.1 to 12.6 V (from the PC-Link header)• Current Draw : 100 mA at 12V (400 mA during the GSM transmission)• Operating Environment : 5 º C to 40º C

(40º F to 104º F)


TL265GS


Features:• Fully redundant Internet and GSM/GPRS dual-path alarm

communication• Integrated call routing• Panel remote uploading/downloading support via GSM/GPRS and

Internet• Advanced remote and local programming via DLS IV• Keypad programming through WT5500 wireless keypad• Individual Periodic Test Transmission via GSM/GPRS and Internet• Supervision heartbeats via GSM/GPRS and Internet• 128-bit AES encryption via GSM/GPRS and Internet• Full event reporting• Installer code• SIA format• PC-Link connection• Signal strength and trouble display• Optional Network Lock and SIM Lock• PC9155 replacement front plate (8 LEDs) included • Quad-Band: 850 MHz, 1900 MHz, 900 MHz and 1800 MHz


TL265GS


Compatible Receivers:Sur-Gard System I Receiver: version 1.10 and higherSur-Gard System II Receiver: version 2.00 and higherSur-Gard SG-DRL3-IP: version 2.20 and higher (for Sur-Gard System III Receiver)

Compatible Control Panel:PC9155 Alexor Wireless Panel version 1.0 and higher

Product Model and Accessories:TL265GS: For International market GS-15ANTQ: Antenna Extension Kits with 15 feet cable GS-25ANTQ: Antenna Extension Kits with 25 feet cableGS-50ANTQ: Antenna Extension Kits with 50 feet cablePCLINK-5WP: PCLINK Kits for the programming with DLS IV


Global Approvals

GS2065 GSM/GPRS Wireless Alarm CommunicatorTL265GS Internet and GSM/GPRS Dual-Path Alarm Communicator

Now • FCC/IC, UL, ULC (North America)• CE, WEEE (Europe)• A-Tick (Australia/New Zealand)

September 2009• ANATEL (Brazil)• CNC (Argentina)• ICASA (South Africa)

November 2009•IMQ (Italy)


GS2065/TL265GS– Installation and programming


Installation

GS2065/TL265GS Installation

BEFORE YOU BEGIN

Have the following ready before installation:

• DSC DLS IV Programming Software • Control panel backup battery• Battery connection harness• Batteries for WT5500 2-way wireless keypad• Screwdriver• PCLINK-5WP Kits

PCLINK Header (Female) RJ11 cable Serial Header (DB9) Transformer (w/ connector to PCLINK header) 4 power plugs (international plugs)


Installation


Summary of Installation Steps

Step 1 – Connect the PCLINK-5WP cable between the computer and GS2065/TL265GS

Step 2 – Program the GS2065/TL265GS using DLS IV

Step 3 – Insert the SIM card in the GS2065/TL265GS

Step 4 – Connect the GS2065/TL265GS to the PC9155

Step 5 – Test for best signal strength location

Step 6 – Program Communication Sections on the PC9155 via keypad

Step 7 – Test communication

NOTE: All the options of the communicator also could be programmed through WT5500 2-way wireless keypad. Please see details in product manual.


GS2065/TL265GS – Installation

Step 1 – Connect the GS2065/TL265GS to the DLS computer using the PCLINK- 5WP

· If connected to the PC9155, power down the PC9155 and remove the PC-LINK connection

· Insert the PCLINK-5WP header to GS2065/TL265GS

· Connect the DB9 serial connector to the DLS computer

· Apply power to the PCLINK-5WP

Installation



Installation

Step 2 – Program the GS2065/TL265GS usin g DLS IV

Step 2

Step 2.1 – Open DLS IV



Installation

Step 2.2 – Create an account• Select ‘New Account’• Enter the account details

• Account Name• Panel Type (Communicator Module)• Connection Type (TL Network)

Account Name

Panel Type

Connection Type



Installation

Step 2.3 – Module IP Address• Enter the IP address for the module

Communicator IP Address



Installation

Step 2.4 – Enter SMS Details• Change ‘Connection Type’ to ‘SMS’• Enter a ‘User Name’• Enter a ‘Password’

• Select ‘Create’

Connection Type User Name

Password

Create



Installation

Step 2.5 – Program the GS/IP options• The account will open• Select the ‘GS/IP’ tab• Enter the required information in the ‘GS/IP Options’ screen



Installation

Step 2.6 – Program the Receivers options· Enter the required information in the ‘Receivers’ screen



Installation

Step 2.7 – Program the GPRS options· Enter the required information in the ‘GPRS’ screen



Installation

Step 2.8 – Load the programming to the communicator· Use “Global Download” and choose “PC-LINK” as the connection type. Then click “OK”



Installation

Step 3 – Insert the SIM card

Ensure that the GS2065/TL265GS is powered down before inserting the SIM card


Installation


Step 4 – Install and wire the communicator to the control panel (on-site)GS2065/TL265GS: See details in product manual for PC9155 control panelFor PC9155D or PC9155G Kit, GS2065/TL265GS is pre-installed with the control panel

Red Wire


Installation


Step 5 - Test for best signal strength location

Ensure the SIM card is inserted Power up the control panel

Check Green LEDs. You must achieve full or medium signal strength. See details in product manual.

If signal strength is poor, must relocate the control panel or use an external extension antenna kits


Installation


Step 6 – Program communication options on the control panel via keypad

GS2065/TL265GS with PC9155 control panel o Sections [301], [302], [303], [305] : Program Communication

Path• DCAA - Internal (Ethernet 1,

Ethernet 2, GPRS 1, GPRS 2)

• DCBB - Ethernet Receiver 1• DCCC - Ethernet Receiver 2

(backup)• DCDD - GPRS Receiver 1• DCEE - GPRS Receiver 2

(backup)

o Section [350] : Program Communication Format (Communicator)• (If Option [301] (above) is set to DCAA,

Option [350] must be set to SIA, sub-option 5)

o Sections [351] to [376] : Program Call Directiono Section [382] : Enable T-LINK Interface (Option [5])o Section [383] : Program Back-up or Independent Communicationo Section [167] : Enable Communication Wait For ACK (Set to 60

seconds)o Section [401] : Enable DLS Session Through GPRS or Ethernet

(Option [1])


Installation


Step 7 – Test communication

1. Disconnect incoming phone line from TIP and RING on the control panel 2. Verify that LED 2 is on, this indicate that the unit is active3. Create an alarm transmission 4. Verify alarm transmission by calling monitoring station5. Re-connect the phone line, if necessary

For back-up communication applications, perform steps 1 to 5For primary communication applications, perform steps 3 and 4 only


Programming

GS2065/TL265GS Remote Programming

We need several slides here to show how remotely get the DSL connection to re-program the communicator •Via Ethernet/Internet connection•Vis SMS initiated connection


Installation

LED Display

Trouble Status LED (Yellow)

Please see details about the trouble shooting on page 17 in product manual


Installation

LED Display

Network Connection Status LED (Red)

LED OFF•No network connection issue present

LED ON•Physical Ethernet cable is not connected•DHCP configuration fails•Fails to get an IP address from the GPRS network•GPRS connections has been reset

LED blinks quickly once•Ethernet transmitting

LDE blinks quickly twice•Ethernet receiving


Installation

LED Display

Signal Strength LED 2 (Green)

Signal Strength LED 1 (Green)

Green LED 2 blinks quickly once•GPRS transmitting

Green LED 2 blinks quickly twice•GPRS receiving


Installation

Keypad Trouble Display

Trouble Condition•Alternate Communicator Trouble

Description•SIM Card Lock•GSM Trouble•Ethernet Trouble•Central Station Receiver Trouble•Supervision Trouble•SMS Config Trouble


GS2065/TL265GS– Applications


Applications

GS2065/TL265GS Call Routing (Internal)

Communicator Controlled Call Routing – Backup (dual-path)

– Redundant (dual-path)

Required ProgrammingPanel Sections [301], [302],[303] and [305]

• Any of them could be programmed as DCAADCAA (default): Ethernet 1 → Ethernet 2 → GRPS 1 → GPRS 2

Communicator Sections [005]Option [004] - Primary and backup path

[ON]: GPRS path primary, Ethernet path backup

[OFF]: Ethernet path primary, GPRS path backup

Option [005] - Redundant between GPRS path and Ethernet path [OFF]: Disable

redundancy[ON]: Enable redundancy


Applications


Backup Mode 1: Ethernet Primary, 4 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver* 1

IP Receiver 2

IP Receiver 3

IP Receiver 4

Tx 2 failed, TX3

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2


Applications


Backup Mode 2: Ethernet Primary, 2 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2

Tx 2 failed, TX3


Applications


Backup Mode 3: GPRS Primary, 4 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

IP Receiver 3

IP Receiver 4

Tx 2 failed, TX3

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2


Applications


Backup Mode 4: GPRS Primary, 2 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2

Tx 2 failed, TX3


Applications


Redundant Mode: 4 Receivers – (Redundancy between GSM/GPRS path and Ethernet/Internet path)

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

IP Receiver 3

IP Receiver 4

TX1, GPRS path

TX 1, Ethernet path

TX 1 failed, TX 2 via GPRS path

TX1 failed, TX 2 via Ethernet path

NOTE: The application requires 4 different SG receivers or SG-DLR3 IP line cards


Applications

GS2065/TL265GS Call Routing (External)

PC9155 Panel Controlled Call Routing Backup (triple-path)

• Panel section [383] – Options [2],[3] and [4] enabled

• Panel section [380], Option [6] disabled Redundant (triple-path)

• Panel sections [351] – [376] Options enabled Alternate (triple-path)

• Panel section [380] – Option [6] enabled

Required ProgrammingPanel Sections [301], [302],[303] and

[305] • Phone #: Phone number of the receiver • DCBB: Ethernet Receiver 1• DCCC: Ethernet Receiver 2• DCDD: GPRS Receiver 1

• DCEE: GPRS Receiver 2


Applications


PC9155 Panel Controlled Call Routing–Backup: Panel Section [383] – Options [2],[3] and [4] enabled

DC DD[305]

DC C C[303]

DC B B[302]

1-800-xxxxxxx[301]

DC DD[305]

DC C C[303]

DC B B[302]

1-800-xxxxxxx[301]

Phone Line Receiver 1

IP Receiver 1

IP Receiver 2

IP Receiver 3

Phone Line path

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

TX 1

Tx 1 5 failures, Tx2



Example


Applications


PC9155 Panel Controlled Call Routing– Redundant: Panel Sections [351] – [376] Options enabled

DC DD[305]

DC C C[303]

DC B B[302]

1-800-xxxxxxx[301]

DC DD[305]

DC C C[303]

DC B B[302]

1-800-xxxxxxx[301]


IP Receiver 2

IP Receiver 3

IP Receiver 4

Phone Line path

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

TX 1

TX 1

TX 1

TX 1

Example


Applications


PC9155 Panel Controlled Call Routing–Alternate: Panel section [380] – Option [6] enabled

DC DD[305]

DC C C[303]

DC B B[302]

1-800-xxxxxxx[301]

DC DD[305]

DC C C[303]

DC B B[302]

1-800-xxxxxxx[301]


IP Receiver 1

IP Receiver 2

IP Receiver 3

Phone Line path

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

TX 1

Tx 1 1 failure, Tx2

Tx 2 1 failure, Tx3

Tx 3 1 failure, Tx4

5 rounds total

Example


Applications

Other Applications

Keypad Programming •All options of the communicator could be programmed from WT5500 keypad •Control Panel option [851], Communicator option [999]-55NOTE: A module reset is required if any options have been changed by the keypad.

Periodic Test transmission•Individual periodic test transmission via GPRS and Ethernet•Customized Time of Day for test transmission•Daily, Weekly and Monthly Interval•Communicator Options [026], [028], [029], [124], [125], [224] and [225]NOTE: Enabling this feature will require more data usage.

Encryption•128 Bit AES Encryption •Turned on by central monitoring station Sur-Gard receiver•Encrypted communications enabled after next event sent to the receiverNOTE: Enabling this feature will require more data usage.


Applications

Other Applications

Supervision Type•Commercial Type and Residential Type•Commercial Type can Swap Detection and require more data usage than Residential Type•Communicator option [005]-[3]

Heartbeats Interval•Should be 65 seconds less than the supervision window programmed at the receiver. •Send heartbeats to Ethernet 1 and/or GRPS 1 receiver•Communicator option [004] and [005]-[1]&[2]

NOTE: Enabling this feature will require more data usage.


Applications

Other Applications

Installer Code•Required to program the communicator by using DLS IV remotely/locally•Communicator option [11]

Optional Carrier and SIM Lock •Lock the unit to a specific carrier’s network•Lock the unit to a SIM card with a specific PIN numberNOTE: This feature is available upon request of specific carrier networks.

Public APN•Use Public APN for DLS session if the communicator is operating on a private APN•GPRS Login User Name and Password might be required •Communicator option [221] to [223]


Applications

Other Applications

Power Save Mode•Extend the battery duration when an AC power loss on control panel•Ethernet functionality turned off until a new event need to be transmitted•Network Connections LED: OFF•Incoming DLS connection will not be possible

Hardware Default •Reset the programming options to the factory setting (default values)NOTE: Please see details in product manual

Software Update •Update the firmware through DLS IV locally via PCLINK•Update the firmware through DLS IV remotely via Ethernet/Internet (TL265GS only)•Communicator option [005]-[6]


Applications

Other Applications

System Information •Upload and read the system status by using DLS IV•Also readable from WT5500 keypad

Firmware versionEthernet IP addressEthernet gateway IP addressGRPS IP addressSIM numberGSM phone numberIMEI numberMAC addressModule Default/Reset


Applications

SIA Report Code

Event SIA Data Code SIA Address Field Panel Absent Trouble ET 001Panel Absent Trouble Restore ER 001Radio Activation Restore RS 001Ethernet 1 Test Transmission RP 001GPRS 1 Test Transmission RP 003GPRS 2 Test Transmission RP 004FTC Restore YK 001

Example: Nri0 ET001 N= New Eventri0=Partition/Area identifierET= Panel Absent Restore 001=Zone 001

NOTE: GPRS 2 Test Transmission will only be sent when two different APNs are programmed.

2-Way Wireless Security Suite GS2065/TL265GS Product Technical Training (International version)

Documents

Transcript of 2-Way Wireless Security Suite GS2065/TL265GS Product Technical Training (International version)