2 SINTRA Back Panel - · PDF fileThe ultimate purity in Sintering for ZrO2 SINTRA Quick Start...
A B C D E F N K L I J H G M The ulmate purity in Sintering for ZrO 2 SINTRA Back Panel 2 3 1 3 2 4 5 6 7 Remove the polyethylene foam. Carefully liſt the SINTRA and posion it on its base. DO NOT liſt the furnace by the liſt shaſt. Recommend two persons. Check that the main power switch at the rear of the furnace is OFF . Insert the electrical power cord into the furnace power inlet. Plug the electrical power cord into the wall power outlet. Switch power ON. Audio signal will be heard. The logo “Sintra” will appear in the color LCD. Press the ON/OFF key on the front panel. The furnace is in Idle mode. The plaorm will descend automacally. Following this pression WARNING! Place ceramic table on liſt prior to operang! Your new SINTRA is ready for program selecon and operaonal use! 200 programs are available. Program No.1-15 are BUILD-IN parameters. 250 programs for Sintra Plus. It is very important that you keep the firing chamber closed in the idle mode to prevent moisture from entering the muffle. For more details on programming the furnace, refer to the complete user guide. We welcome your feedback and suggesons at [email protected] A B C D E F G H I J K L M LCD Control Panel Program indicator Temperature indicator and Status indicator Arrows to move from one parameter to another on display Numeric keypad ON/OFF turns the furnace on/off. Switches to idle mode START the sintering cycle STOP/LIFT : raise and lower the firing plaorm. Interrupts the sintering cycle. AIR on/off: temporarily open the air cooling while in cycle. Manually permits acve cooling even if not programmed in cycle PROG: set furnace in mode to select program CLR: clears the previous key selecon ENT : Confirms the selecon of a program or a parameter EXCHANGE BETWEEN Graph and Parameters
Transcript of 2 SINTRA Back Panel - · PDF fileThe ultimate purity in Sintering for ZrO2 SINTRA Quick Start...
AB
C
D
E FN
KL
IJH
GM
The ultimate purity inSintering for ZrO2
SINTRA Back Panel
2
3
1
3
2
4
5
6
7
Remove the polyethylene foam. Carefully lift the SINTRA and position it on its base. DO NOT lift the furnace by the lift shaft. Recommend two persons.
Check that the main power switch at the rear of the furnace is OFF.
Insert the electrical power cord into the furnace power inlet. Plug the electrical power cord into the wall power outlet.
Switch power ON. Audio signal will be heard. The logo “Sintra” will appear in the color LCD.
Press the ON/OFF key on the front panel. The furnace is in Idle mode.
The platform will descend automatically. Following this pression
WARNING! Place ceramic table on lift prior to operating!
Your new SINTRA is ready for program selection and operational use!
200 programs are available. Program No.1-15 are BUILD-IN parameters. 250 programs for Sintra Plus.
It is very important that you keep the firing chamber closed in the idle mode to prevent moisture from entering the muffle.
For more details on programming the furnace, refer to the complete user guide.
We welcome your feedback and suggestions at [email protected]
A
B
C
D
E
F
G
H
I
J
K
L
M
LCD Control PanelProgram indicatorTemperature indicator and Status indicatorArrows to move from one parameter to anotheron displayNumeric keypadON/OFF turns the furnace on/off. Switches to idle modeSTART the sintering cycleSTOP/LIFT: raise and lower the firing platform. Interrupts the sintering cycle.AIR on/off: temporarily open the air cooling while in cycle. Manually permits active cooling even if not programmed in cyclePROG: set furnace in mode to select programCLR: clears the previous key selectionENT: Confirms the selection of a program or a parameterEXCHANGE BETWEEN Graph and Parameters
The ultimate purity inSintering for ZrO2
SINTRAQuick Start Guide
Congratulations on your new purchaseof the SINTRA, Zr sintering furnace.
Below are 7 easy steps to help you get started.
DCM
124A
- Si
ntra
Qui
ck G
uide
Remember! Safety First!
Before removing any covers or undertaking any repairs DISCONNECT THE FURNACE FROM THE POWER SUPPLY.
For support center in your region, visit our technical contact page on our website
www.shenpaz.com
Quick Trouble Shooting
HEATING
No Heating The main input is disconnect or one of the fuse are blowed
Check the main input wire connection, turn off and on the furnace, or check the 8A, 5A 20A heating fuse
If the furnace still doesn’t heat up
Contact your dealer for checking or replacement
PROGRAMATION
Correlation of parameters
The program is not running or not working properly
Check program parameters and limits. Erase and rewrite program parameters.
If the furnace still doesn’t work.
Contact your dealer for checking and reprogramming
1
43
2
Programming
Press the “ON “button thenChoose your program number “xx” from the pre memorized programs Confirm by pressing the “ENT” key Press “START” to launch cycle.
FURNACE STUCK WITHIN PROGRAMMING
No response from button
The furnace need to be restart
Press “stop” button and restart the furnace from the Rocker switch
Still no response Contact your dealer for checking or replacement
Start Here!ShenPaz Dental Ltd.
5 HaTasia St. Ramat Gabriel Ind. Park, Migdal HaEmek 23101, Israel
Tel: +972 (0)3 562 0428 Fax: +972 (0)4 6042040
