2 OMC231120 BSC6900 GSM V900R011 Installation & Commissioning ISSUE 1

BSC6900 GO Installation & Commissioning

www.huawei.com

Copyright © 2010 Huawei Technologies Co., Ltd. All rights reserved.

ForewordForewordThe OMU operating system is installed before the OMU is The OMU operating system is installed before the OMU is

delivered

BSC6900 commissioning is performed after the hardware

is installed and before the services are provided. It aims

to ensure that the BSC6900 can work normally through

tasks such as equipment verification, BSC6900 board

software and data file loading, interface verification, and

service verification.service verification.

Copyright © 2010 Huawei Technologies Co., Ltd. All rights reserved. Page1

ReferencesReferences“BSC6900 GSM Commissioning Guide”BSC6900 GSM Commissioning Guide

“BSC6900 OMU Administration Guide”


ObjectivesObjectivesUpon completion of this course you will be able to:Upon completion of this course, you will be able to:

Describe BSC6900 commissioning procedure

Outline OMU software functions

Complete BSC6900 commissioning


ContentsContents1 BSC6900 O&M System Introduction1. BSC6900 O&M System Introduction

2. BSC6900 Software Installation

3. BSC6900 Commissioning


BSC6900 O&M SubsystemBSC6900 O&M Subsystem ComponentComponent

LMT

OMUa boards

SCUa boards

OM modules

on other boards on other boards


BSC6900 O&M SubsystemBSC6900 O&M SubsystemBSC6900 O&M system adopts server and client modeBSC6900 O&M system adopts server and client mode

OMU as a server

LMT as a client

EMS (Element Management System) systemg y y

iManager M2000 works for integrated O&M


OMU Ethernet Adapter ConfigurationOMU Ethernet Adapter Configuration

An OMU board is configured An OMU board is configured

with six Ethernet adapters in

total total.

ETH0 and

ETH1(bond1/bond1:0 )

ETH2: ETH2 (bond2)

ETH3-UPDATE (bond3)

ETH4-SCU7 and ETH5-SCU6 ETH4 SCU7 and ETH5 SCU6

(bond0 (vlan1/vlan1:0))


Definitions of IP addresses of the OMUDefinitions of IP addresses of the OMU The OMU IP addresses include:

External fixed IP addresses

Internal fixed IP addresses

External virtual IP addresses

Internal virtual IP addresses

Debugging IP address.

Backup channel IP address of the active and standby OMUs.

(Optional)

Before an OMU is delivered, six IP addresses are configured. The

d f l IP dd h i f i default IP addresses may not meet the requirement of onsite

planning. All the OMU IP addresses need to be planned on site,

and some of the IP addresses need to be re-set


and some of the IP addresses need to be re set.

See RemarksSee Remarks


OMU IP Address PlanningOMU IP Address Planning

IP Address Planning Principle

Internal fixed IP

dd

The preset IP addresses of the internal Ethernet adapters are:

address Active BAM: 80.168.3.50 (255.0.0.0)

Standby BAM: 80.168.3.60 (255.0.0.0)

External fixed IP

address

The preset IP addresses of the external Ethernet adapters are:

Active BAM: 172.121.139.201 (255.255.255.0)

Standby BAM: 172.121.139.202 (255.255.255.0)

The settings can be reconfigured on site based on the actual

networking topologynetworking topology


OMU IP Address PlanningOMU IP Address Planning

IP Address Planning Principle

Internal/External

virtual IP

The virtual IP address is set in the same subnet with the

internal/ external fixed IP addresses of the active and standby

address BAMs

Backup channel The preset backup channel IP addresses of the active and

standby BAMs are:IP addresses standby BAMs are:

Active BAM: 192.168.3.50 (255.255.255.0)

Standby BAM: 192.168.3.60 (255.255.255.0)

Th IP dd h ld t b h dThe IP address should not be changed

Commissioning

IP address

The preset commissioning IP addresses are:

Active BAM: 192.168.6.50 (255.255.255.0)IP addressStandby BAM: 192.168.6.60 (255.255.255.0)

The IP address should not be changed.NOTE: The LMT can access the OMU only through the external virtual IP addres


OMU Internal Network IP Address PlanningPlanning

Active OMUa Standby OMUaVirtual IP

80.168.3.40/8

Internal80.168.3.50/8 80.168.3.60/8

ETH4-SCU7 ETH4-SCU7networksegment

192.168.3.50/24 192.168.3.60/24

ETH5-SCU6 ETH5-SCU6

Intel Ethernet adapters

Intel Ethernet adapters

Dedicated b kETH3- ETH3-

SCUa SCUa

backup channel

ETH3UPDATE UPDATE

BackboardBSC6900 FAM


BSC6900 FAM

OMU External Network IP Address Planning

Active OMUa Standby OMUaVirtual IP 172.121.139.200/24

172.121.139.201/24 172.121.139.202/24

ExternalnetworkSegment GE adapter

ETH0

ETH1

ETH0

ETH1

Hub

LMT/

ETH2 ETH2Commissioning Ethernet adapter

LMT/M2000

192.168.6.60/24

192.168.6.50/24


BSC6900 SoftwareBSC6900 Software

MPS/EPS

Host Software

LMT

LMT SoftwareHost Software

ProgramFile

Windows XPSP2

Java Environment

OMU Server

Data File

OMU Application

OMU Server

Patch File(optional)

Dopra Linux Mysql Database


OMU SoftwareOMU SoftwareThe OMU software The OMU software

consist of multi-

level service level service

monitoring entities

and service

processes


OMU Software Installation ProcedureOMU Software Installation Procedure

Obtain the Installation Information on the OMU Obtain the Installation Information on the OMU

Logging In to the OMU

Uploading the OMU Application Installation Package to

the OMU

Installing the OMU Application in the Active Workspace

Checking the Installation Directory of the OMU g y

Applications

Checking the Status of omud Processg


Obtain the Installation Information on the OMU

Before the installation, obtain the following information

from Data Sheet of BAM Software Installation

Password of the operating system administrator

Fixed IP address of the external network, virtual IP address Fixed IP address of the external network, virtual IP address

of the external network, or debugging IP address of the

OMU. OMU.


Logging In to the OMULogging In to the OMU

On the computer run the

SSH terminal, PuTTY

Enter the IP address of

the OMUthe OMU

Log in to the OMU as

user root


Uploading the OMU Application Installation Package to the OMU

D th BSC6900 i ft k t th Decompress the BSC6900 version software package to the

local drive D

Log in to the OMU through the psftp software

Run the lcd D:\ to set the local directory

Run the mkdir /mbsc/upgrade to create the target directory

Run the cd /mbsc/upgrade to go to the target directory

Run the put -r V900R011C00 to upload the OMU application

installation packet to the OMU

After the loading is complete, enter the exit command to exist the

psftp software


Installing the OMU Application in the Active Workarea

Assume that the OMU application installation package pp p g

install_bam.sh is saved in

/mbsc/upgrade/V900R011C00/install/setup.

On the PuTTY terminal, run the following commands

cd /mbsc/upgrade/V900R011C00/install/setup

chmod +x ./install_bam.sh

./install_bam.sh

Enter the run mode

Setting the office name

Setting the languageSetting the language

Setting the admin/FTP password

Setting the external virtual IP address


Setting the OMU system type


Setting the run mode of productSetting the run mode of product

Setting the office name Setting the office name

Setting the language Setting the language



Setting the admin/FTP password Setting the admin/FTP password

Setting the external virtual IP address



Setting the OMU system typeSetting the OMU system type

Confirming the installation

Enter Y to install the OMU applications Enter Y to install the OMU applications.

When the message"Install OMU succeed!" is displayed, you

i f h h li i f ll can infer that the OMU applications are successfully

installed.


Checking the Installation Directory of the OMU Applications

The version a and version bThe version_a and version_b

folders save active/standby OMU

workspace files.

Log in to the OMU by PuTTY

Run the cd /mbsc/bam

Check whether the OMU Check whether the OMU

installation directory


Checking the Status of omud ProcessChecking the Status of omud Process

Log in to the OMU by PuTTYLog in to the OMU by PuTTY

Run the /etc/rc.d/omud status

The returned information is running, it means the omud is

working normally

The returned information is unused, run the /etc/rc.d/omud

start command to start the omudstart command to start the omud

The returned information is neither running nor unused,

reinstall the OMU application in the active workspacereinstall the OMU application in the active workspace


ContentsContents3. BSC6900 Commissioning3. BSC6900 Commissioning

3.1 BSC6900 Commissioning Introduction

3 2 BSC6900 C i i i P d3.2 BSC6900 Commissioning Procedure


Introduction to BSC6900 CommissioningIntroduction to BSC6900 Commissioning

Definition of BSC6900 CommissioningDefinition of BSC6900 Commissioning

The commissioning of equipment, BSC6900 board

ft d d t fil l di i t f software and data file loading , interfaces

verification , and services verification after hardware

i t ll tiinstallation

To ensures that the BSC6900 works properly as

designed


Preparation For BSC6900 Commissioning

Preparation For BSC6900 Commissioningp g

Verify hardware status

BSC6900 hardware is installed and passed the hardwareBSC6900 hardware is installed and passed the hardware installation check and powering-on check

OMU is configured before deliveryOMU is configured before delivery

LMT PC meets the configuration requirements

Software preparationSoftware preparation

BAM and LMT application software are ready

License file is readyLicense file is ready

MML command script for initial configuration is ready


Preparation For BSC6900 Commissioning (Cont.)

Verify commissioning network status

At least one BTS are connected to the local BSC6900. The BTS

should have passed commissioning and can provide basic

functions

At least one set of Core Network (CN) equipment is connected to

the local BSC6900. The CN equipment should have passed the

i i i d id b i f ticommissioning and can provide basic functions

The MSs are ready for test and are registered in the HLR


ContentsContents3. BSC6900 Commissioning3. BSC6900 Commissioning

3.1 BSC6900 Commissioning Introduction

3 2 BSC6900 C i i i P d3.2 BSC6900 Commissioning Procedure


BSC6900 Commissioning ProcedureBSC6900 Commissioning Procedure

C i i i P itCommissioing Prerequsites

Check hardware operating Status

L d BSC6900 B d

Local operation

Remote operation

Verify OMU Verify OMU

Load BSC6900 Board Software and Data

files

Connect BSC6900 to M2000

Local operationRemote operation y

through USB Disky

Locally

Log in to BSC6900

based on local coopertation

Remote operation Log in to BSC6900 through LMT

Update OMU Database

Remote operation

Continued in the next page

Activate and Verify the License

Copyright © 2010 Huawei Technologies Co., Ltd. All rights reserved. Page35Page35

BSC6900 Commissioning Procedure (Cont.)

V if i t f

Remote operation

Verify interfacesthrough LMT

Set NE to be in maintenance mode Verify GSM Inteface

Remote operation based on localcoopertation

Verify interfaces through M2000

End the maintenance

Verify Interface

Verify GSM servicesEnd the maintenance

mode of NE

Create scheduled task

Handle alarms


Checking the Operating Status of the Hardware

Before verifying the equipment ensure that the cabinet is Before verifying the equipment, ensure that the cabinet is

powered on and operates normally

Checklist of the power supply to the cabinet components

Component Normal LED Status

Board The green RUN LED on the board panel flashes every other second.

The green STATUS LED on the panel of the fan box flashes every

Fan box

g p y

other second after the subrack and independent fan subrack are

powered on.

Power distribution

monitoring board

The green RUN LED on the board panel flashes every other second

and the ALM LED is also OFF.


Main Steps of CommissioningMain Steps of CommissioningVerifying the OMU 1. Logging in to the OMU

2. Check the running status

Activating and Verifying the License

L di h BSC6900 B d S f d D Fil

g of the OMU process

3. Query the current version of the OMU application.

Loading the BSC6900 Board Software and Data Files

Verifying the Interfaces

4. Change the external fixed/ virtual IP address

6. Change the name and set th k d f th OMU

Handling the Alarms

the work mode of the OMU

7. Check the operating status of the OMU

Verifying the Services

Connecting the BSC6900 to the M2000

Creating Scheduled Tasks



Logging In to the OMULogging In to the OMU

On the computer run the

SSH terminal, PuTTY

Enter the IP address of

the OMUthe OMU

Log in to the OMU as

user root


Check the running statusCheck the running status Run the /etc/rc d/omud status command to check the Run the /etc/rc.d/omud status command to check the

running status of the OMU process.


Query the current version of the OMU application

h d b d d i h hRun the cd /mbsc/upgrade command to switch to the

OMU installation directory, and then run the ls command

to query the current version of the OMU application.

If the version of the OMU application is different from that pp

required by the operator, Uninstalling the OMU application

firstly , and then install the OMU application in the active y

workspace


Querying the Network Configuration of the OMU Ethernet Adapters

Querying the external fixed IP address: ifconfig bond1Querying the external fixed IP address: ifconfig bond1

Querying the external virtual IP address: ifconfig bond1:0

Querying the internal fixed IP address: ifconfig vlan1

Querying the internal virtual IP address: ifconfig vlan1:0Querying the internal virtual IP address: ifconfig vlan1:0

Querying the debugging IP address: ifconfig bond2

Querying the IP address for the backup channel between

the active OMU and the standby OMU: ifconfig bond3y g


Change the external IP addressChange the external IP address Run the cd /mbsc/bam/version_a/bin/bam command to switch

to the directory where the omutool program locates.

Run the ./omutool command to start omutool.

Run the ./omutool extercard The external fixed IP address The subnet mask The gateway IP address command to change the

external fixed IP address and the subnet mask.

./omutool extercard 10.161.10.100 255.255.255.0 10.161.10.1

Run the ./omutool extervip The external virtual IP address The subnet mask command to change the external virtual IP

address and the subnet mask address and the subnet mask.

./omutool extervip 10.161.10.102 255.255.255.0


Change the name and set the work mode of the OMU

Run the ./omutool hostname OMU name command to change Run the ./omutool hostname OMU name command to change

the name of the OMU.

For example, you can run the following command and then press

Enter to change the OMU name to omu_123: ./omutool hostname

omu_123.

Set the work mode of the OMU according to the number of

OMUa boards that are configured.

If l OMU b d i fi d th / t l d l d If only one OMUa board is configured, run the ./omutool dualmode

single command to set the work mode to the single-server mode.

If two OMUa boards (active and standby OMUa boards) are If two OMUa boards (active and standby OMUa boards) are

configured, run the ./omutool dualmode dual command to set the

work mode to the dual-server mode.


Check the operating status of the OMUCheck the operating status of the OMU

Run the /etc/rc d/omud startRun the /etc/rc.d/omud start

command to start the OMU

application. pp

Run the ps -afx command to

check the operating status of p g

the OMU.

You can infer that the OMU is

in normal state if all OMU

processes exist in the OMU

active workspace active workspace

directory/mbsc/bam/version_a/

bin/bam/monitor.


BSC6900 Commissioning Procedure

Verifying the OMU Locally


L di h BSC6900 B d S f d D FilLoading the BSC6900 Board Software and Data Files


Handling the Alarms







Activating and Verifying the LicenseActivating and Verifying the License

Downloading license to OMU active workspace directory

/ft /li (DLD LICENSE) /ftp/license (DLD LICENSE)

Querying the detail information of the license file (LST

LICENSE)

Activating the license file (ACT LICENSE)

Checking the license consistency between host and OMU

(CMP LICENSE)( )



Loading the BSC6900 Board Software and Data FilesLoading the BSC6900 Board Software and Data Files

Generating the Data File

Cl th d t i th BAM d t b (RST DATA)Clear the data in the BAM database (RST DATA)

Generate the data file in ineffective state

– SET CFGDATAINEFFECTIVESET CFGDATAINEFFECTIVE

– Batch Commands

– FMT DATA

Setting the Loading Mode (SET LODCTRL)

Loading the MPS/EPS/TCS (RST SUBRACK)g

Checking the consistency of the data and the version (ACT CRC &

CMP BRDVER)





L di h BSC6900 B d S f d D Fil

1. Verifying the Abis Interface



Interface

2. Verifying the A Interface

3 V if i th Gb

Handling the Alarms

3. Verifying the Gb Interface

4. Verifying the Ater I t f (O ti l)

Verifying the ServicesInterface (Optional)

5. Verifying the Pb Interface (Optional)





Verifying the Abis InterfaceVerifying the Abis InterfaceVerifying the Abis interface (Abis over TDM)Verifying the Abis interface (Abis over TDM)

Verifying Physical Links at the BSC (DSP E1T1 & DSP OPT)

Verifying the Control Plane on the Abis Interface (DSP

LAPDLNK )

Verifying he timeslot status of the Abis interface (DSP

ABISTS)

To query the Subrack No., Slot No., and Port No. of the timeslots

to be verified, run the MML command (LST BTSCONNECT)

Verifying the Status of Cells and Channels (DSP BTSSTAT)


Verifying the Abis InterfaceVerifying the Abis InterfaceVerifying the Abis interface (Abis over IP)Verifying the Abis interface (Abis over IP)

Verifying Physical Links at the BSC (DSP ETHPORT )

Verifying the Control Plane on the Abis Interface (DSP

LAPDLNK )

Verifying the User Plane on the Abis Interface (DSP

ADJNODE & DSP IPPATH)

Verifying the Status of the Cells and Channels (DSP BTSSTAT)


Verifying the A InterfaceVerifying the A Interface Verifying the A interface (A over TDM) Verifying the A interface (A over TDM)

Verifying Physical Links at the BSC (DSP E1T1 & DSP OPT)

V if i th C t l Pl th A I t fVerifying the Control Plane on the A Interface

DSP N7DPC

DSP MTP3LNK

DSP MTP2LNK

Verifying the User Plane on the A Interface (DSP ACIC)

To query the OPC Index and DPC Group Index of the E1/T1 to be verified on the A interface, run the MML command LST AE1T1.


Verifying the A InterfaceVerifying the A InterfaceVerifying the A interface (A over IP) Verifying the A interface (A over IP)

Verifying Physical Links at the BSC (DSP ETHPORT )

Verifying the Control Plane on the A Interface

DSP N7DPC

DSP M3LKS

DSP SCTPLNK

Verifying the User Plane on the A Interface (DSP ADJNODE

& DSP IPPATH )& DSP IPPATH )


Verifying the Gb InterfaceVerifying the Gb InterfaceVerifying the Gb interface (Gb over FR) Verifying the Gb interface (Gb over FR)

Verifying the status of the Bearer Channel (DSP BC)

Verifying the status of the Network Service Virtual

Connection (DSP NSVC)

Verifying the SIG BSSGP Virtual Connection (SIGBVC) status

of the Network Service Entity (DSP SIGBVC & DSP PTPBVC)

To query the configuration of the NSE to be verified, run the MML

command LST NSE


Verifying the Gb InterfaceVerifying the Gb InterfaceVerifying the Gb interface (Gb over IP) Verifying the Gb interface (Gb over IP)

Verifying the status of the Network Service Virtual Link (DSP

NSVL) NSVL)

To query the configuration of the local or remote NSVL to be verified, run the MML command LST NSVLLOCAL or LST NSVLREMOTE.run the MML command LST NSVLLOCAL or LST NSVLREMOTE.

Verifying the status of the IP Route (DSP GBIPROUTE)

Verifying the SIG BSSGP Virtual Connection (SIGBVC) status Verifying the SIG BSSGP Virtual Connection (SIGBVC) status

of the Network Service Entity (DSP SIGBVC & DSP PTPBVC)

To query the configuration of the NSE to be verified run the MMLTo query the configuration of the NSE to be verified, run the MML command LST NSE


Verifying the Ater and Pb Interface (Optional)

Verifying Physical Links at the BSC (DSP E1T1 & DSP OPT)Verifying Physical Links at the BSC (DSP E1T1 & DSP OPT)

Verifying the Ater Interface

Verifying the Status of Timeslots on the Ater interface. (DSP

ATERTS)

If the TCS is configured remotely, run the MML command DSP

ATERSL to query whether the Ater signaling link is normal.

Verifying the Pb Interface

Verifying the LAPD link on the Pb interface (DSP LAPDLNK)

Verifying the status of the circuit on the Pb interface (DSP PBCIC)







Handling the Alarms

Verifying the Services Verifying the GSM Services





Handling the Alarms Generated During the Commissioning

Handling Alarms During Commissioning Handling Alarms During Commissioning

Checking alarm on the LMT

Handling the Alarms by LMT online help


Verifying the GSM ServicesVerifying the GSM ServicesTo be sure BSC can provide services defined in license fileTo be sure BSC can provide services defined in license file

Basic services

The basic services consist of speech service and data service.

Feature services

The feature services consist of the inter-RAT handover, location

service, and AMR service.

If the result of service verification cannot meet the

expected results, start message tracing on the LMT over expected results, start message tracing on the LMT over

the Um, Abis, A, Gb, Pb, and Ater interfaces.







Handling the Alarms






Connecting the BSC6900 to the M2000Connecting the BSC6900 to the M2000

Connect the BSC6900 to the OM networkConnect the BSC6900 to the OM network

Configure the IP route from the BSC6900 to the M2000

ADD OMUIPRT

ADD EMSIP

Create the BSC6900 on the M2000

iManagerTM M2000

DCN


Creating Scheduled TasksCreating Scheduled Tasks

Scheduled tasks for backing up system dataScheduled tasks for backing up system data

ADD SCHTSK

ADD SUBTSK

Scheduled tasks for backing up logs g p g

ADD SCHTSK

ADD SUBTSK


Thank youwww huawei comwww.huawei.com

2 OMC231120 BSC6900 GSM V900R011 Installation & Commissioning ISSUE 1

Documents

Transcript of 2 OMC231120 BSC6900 GSM V900R011 Installation & Commissioning ISSUE 1