3 d Printer Report , 3d , 3d printer, 3d report, printer report
2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red,...
Transcript of 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red,...
![Page 1: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/1.jpg)
Makeblock Constructor I 3D Printer Kit
1
2. 3D Printer Wiring Guide
![Page 2: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/2.jpg)
Makeblock Constructor I 3D Printer Kit
2
Content
2.1. Parts Required .................................................................................. 3
2.2 preparation ........................................................................................ 7
2.2.1 Add heat sinks on the top of stepper motor driver chip ............... 7
2.2.2 Plug the jumper cap into corresponding position ...................... 10
2.3 Wiring the main board part .............................................................. 11
2.3.1 Connect the stepper motor driver(A4988) to Ramp1.4. ............. 11
2.3.2 Reprap smart controller wiring .................................................. 12
2.3.3 Connect Ramps1.4 to the main board ........................................ 15
2.4 Wiring motors and limit switchs ....................................................... 17
2.4.1 Wiring four stepper motors ....................................................... 19
2.4.2 Wiring the extruder .................................................................... 23
2.4.3 Wring limit switches ................................................................... 27
2.5 Connect power supply cables ........................................................ 32
![Page 3: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/3.jpg)
Makeblock Constructor I 3D Printer Kit
3
2.1. Parts Required
Parts required:
reprap smart controller × 1
ramps1.4 × 1
MEGA2560 compatible board × 1
Stepper motor driver(A4988) × 4
Mega2560 compatible board
Based on the ATmega2560 and used as the microcontroller board of our 3D printer.
![Page 4: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/4.jpg)
Makeblock Constructor I 3D Printer Kit
4
Ramps1.4 Shield
Ramps is short for reprap Arduino mega pololu shield, it is open source and
designed as the shield of 3D printer. For more details about this open source
hardware design can be found on the Reprap Wiki
here:http://reprap.org/wiki/RAMPS_1.4.
![Page 5: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/5.jpg)
Makeblock Constructor I 3D Printer Kit
5
reprap smart controller
Used as LCD display of Constructor I 3D printer, you can easy connect it to your
Ramps using the "smart adapter". It is open source and you can know more details
from here http://reprap.org/wiki/RepRapDiscount_Smart_Controlle
![Page 6: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/6.jpg)
Makeblock Constructor I 3D Printer Kit
6
Smart adapter
Stepper Motor Driver Module (A4988) Pictures are for reference only, please in
kind prevail
![Page 7: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/7.jpg)
Makeblock Constructor I 3D Printer Kit
7
Heat sink for stepper motor driver chip
2.2 preparation
2.2.1 Add heat sinks on the top of stepper motor driver chip
Use scissors for cutting open the tape
![Page 8: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/8.jpg)
Makeblock Constructor I 3D Printer Kit
8
Cut the tape as the same size as heatsink
Stick the tape to the heat sink
![Page 9: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/9.jpg)
Makeblock Constructor I 3D Printer Kit
9
Stick the heatsink to Chip A4988 firmly
Repeat the above step to stick other 3 modules
![Page 10: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/10.jpg)
Makeblock Constructor I 3D Printer Kit
10
2.2.2 Plug the jumper cap into corresponding position
![Page 11: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/11.jpg)
Makeblock Constructor I 3D Printer Kit
11
2.3 Wiring the main board part
2.3.1 Connect the stepper motor driver(A4988) to Ramp1.4.
step1. Plug in the A4988 motor driver module onto Ramp1.4 as shown below.
(ATTENTION: IF ANTI-PLUG, IT WILL SHORT-CIRCUITS.)
![Page 12: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/12.jpg)
Makeblock Constructor I 3D Printer Kit
12
step2. Plug the following 4 motor driver modules onto the board, make sure the
pins insert the female header.
2.3.2 Reprap smart controller wiring
Required parts is shown below.
![Page 13: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/13.jpg)
Makeblock Constructor I 3D Printer Kit
13
Step 1. Wiring the smart adapter
Step 2. Wiring the other end to LCD module
![Page 14: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/14.jpg)
Makeblock Constructor I 3D Printer Kit
14
Step 3. Connect the LCD adapter to Ramp1.4
Step 4. Please double-check if all the modules plug into the female header.
![Page 15: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/15.jpg)
Makeblock Constructor I 3D Printer Kit
15
2.3.3 Connect Ramps1.4 to the main board
Step 1. Install the Ramps1.4 on the top of Mega2560 compatible board, ragged the
right side female header and plug in slowly.
Step2. Double check if all the connections are right.
![Page 16: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/16.jpg)
Makeblock Constructor I 3D Printer Kit
16
The main board part is complete! We need to wire the motor wire, end stop and
power cables.
![Page 17: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/17.jpg)
Makeblock Constructor I 3D Printer Kit
17
2.4 Wiring motors and limit switchs
Electronic wiring as show, this is RepRap original wiring figure and please follow the
actual image to wire. (Because Makeblock Constructor I 3D Printer Kit do not
contain Heated Bed, you don’t need to wire Heated Bed Power and Heated Bed
Thermistor.). Kindly advise you can pay more attention and carefully to avoid faulty
connection.
Note: Please connect the motor wiring as following order: red, blue, green and
black.
![Page 18: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/18.jpg)
Makeblock Constructor I 3D Printer Kit
18
Figure out and remember the position of X/Y/Z motor and every end stop, BE
CAREFUL not to mix up the end stop.
![Page 19: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/19.jpg)
Makeblock Constructor I 3D Printer Kit
19
2.4.1 Wiring four stepper motors
Step1. Connect the X Motor to the connector labeled X. Ensure the Red cable is
closest to the green screw terminals on the RAMPS board (Wire orders from left to
right: red, blue, green and black).
Note: If you don't wiring by color order, the motor motion will be incorrect.
Step 2. Connect the Y Motor to the connector labeled Y. Ensure the Red cable is
closest to the green screw terminals on the RAMPS board. (Wire orders from left to
![Page 20: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/20.jpg)
Makeblock Constructor I 3D Printer Kit
20
right: red, blue, green and black)
Note: If you don't wiring by color order, the motor motion will be incorrect.
Step 3. Check the double-row header area around Z motor driver on the Ramp1.4
board. It can connect 2 Z motors of 3D printer.
![Page 21: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/21.jpg)
Makeblock Constructor I 3D Printer Kit
21
Step 4. Connect the two Z Motors to connectors labeled Z. Ensure the Red cable is
closest to the green screw terminals on the RAMPS board. (Wire orders from left to
right: red, blue, green and black).
![Page 22: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/22.jpg)
Makeblock Constructor I 3D Printer Kit
22
![Page 23: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/23.jpg)
Makeblock Constructor I 3D Printer Kit
23
2.4.2 Wiring the extruder
Check the all components of extruder.
![Page 24: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/24.jpg)
Makeblock Constructor I 3D Printer Kit
24
Step 1. Connect the Extruder Motor to the connector labeled E0. Ensure the Red
cable is closest to the green screw terminals on the RAMPS board(Wire orders from
left to right: red, blue, green and black).
![Page 25: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/25.jpg)
Makeblock Constructor I 3D Printer Kit
25
Step 2. The two red wires from extruder heating pipe have no positive and negative
difference.
Connect the wire to D10, make sure the screw clamp the wire, or else the heater will
not heat up.
![Page 26: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/26.jpg)
Makeblock Constructor I 3D Printer Kit
26
Step 3. The thermocouples lead wires of extruder has no positive and negative
difference as well. You need to connect the lead wires to T0 for detecting
temperature of extruder heater.
![Page 27: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/27.jpg)
Makeblock Constructor I 3D Printer Kit
27
2.4.3 Wring limit switches
Note: Please connect limit switchs to the male header (Area“S” and “–“).
![Page 28: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/28.jpg)
Makeblock Constructor I 3D Printer Kit
28
Step 1. Connect the X Endstop Micro switch to the connector labeled x+. (Area "S"
and "-" on the board, you can connect“S” or “-“ in any order.
)
![Page 29: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/29.jpg)
Makeblock Constructor I 3D Printer Kit
29
Step 2. Connect the Y Endstop Microswitch to the connector labeled y-
![Page 30: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/30.jpg)
Makeblock Constructor I 3D Printer Kit
30
Step 3. Connect the Z Endstop Microswitch to the connector labeled z-
![Page 31: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/31.jpg)
Makeblock Constructor I 3D Printer Kit
31
Step 4. Please check the stop end X/Y/Z connect X+/Y-/Z- connection order
carefully. IF THE CONNECTIONS ARE INCORRECT, THE MACHINE WON’T STOP
MOVEMENT WHILE RETURN TO ZERO. If the machine won’t stop moving, please
check if the end stop connection is correct.
![Page 32: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/32.jpg)
Makeblock Constructor I 3D Printer Kit
32
2.5 Connect power supply cables
Notice the positive and negative difference.
Step1. Connect the two wires of 12 V power supply to the corresponding position.
(The red wire is positive and the black wire is negative)
![Page 33: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/33.jpg)
Makeblock Constructor I 3D Printer Kit
33
![Page 34: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/34.jpg)
Makeblock Constructor I 3D Printer Kit
34
Step2. Another group of 12 V power supply required to be connected as shown in
below figure. According to positive and negative pole, or the board will burn out.
Step3. Connect the extruder fun to the corresponding position as shown in below
figure. (The red wire of fan is positive, the black wire is negative.)
![Page 35: 2. 3D Printer Wiring Guide - robotshop.com · Makeblock Constructor I 3D Printer Kit 20 right: red, blue, green and black) Note: If you don't wiring by color order, the motor motion](https://reader030.fdocuments.in/reader030/viewer/2022041303/5e138bd3dd84da753002dfd2/html5/thumbnails/35.jpg)
Makeblock Constructor I 3D Printer Kit
35
Step4. Please double check if you connect all the leads.
Please confirm as below:
If the stepper motor driver connection is correct?
If the wire connection of stepper motor order is red, blue, green and black?
If the end stop X/Y/Z connection is in correct position?
If the extruder temperature resistor is connect to T0?
If the extruder heating wire is connect to D10?
If the extruder fan connection is correct?
If the power is connection like red to positive and black to negative?