Springer Customized Book List · Springer Customized Book List springer.com
1MRK505273-BEN C en Product Guide REB670 1.2 Customized
Transcript of 1MRK505273-BEN C en Product Guide REB670 1.2 Customized
Relion® 670 series
Busbar protection REB670CustomizedProduct Guide
Contents
1. Application.....................................................................3
2. Available functions..........................................................9
3. Differential protection....................................................13
4. Zone selection..............................................................15
5. Current protection........................................................17
6. Voltage protection........................................................19
7. Frequency protection....................................................19
8. Multipurpose protection................................................20
9. Secondary system supervision.....................................20
10. Control........................................................................21
11. Logic...........................................................................22
12. Monitoring...................................................................22
13. Metering......................................................................24
14. Basic IED functions.....................................................24
15. Human machine interface............................................25
16. Station communication ...............................................26
17. Remote communication..............................................27
18. Hardware description..................................................28
19. Connection diagrams..................................................30
20. Technical data.............................................................36
21. Ordering......................................................................75
Disclaimer
The information in this document is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no responsibility for any
errors that may appear in this document.
© Copyright 2012 ABB.
All rights reserved.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
2 ABB
1. ApplicationREB670 is designed for the selective, reliable andfast differential protection of busbars, T-connections and meshed corners. REB670 canbe used for protection of single and doublebusbar with or without transfer bus, double circuitbreaker or one-and-half circuit breaker stations.The IED is applicable for the protection of mediumvoltage (MV), high voltage (HV) and extra highvoltage (EHV) installations at a power systemfrequency of 50Hz or 60Hz. The IED can detectall types of internal phase-to-phase and phase-to-earth faults in solidly earthed or low impedanceearthed power systems, as well as all internalmulti-phase faults in isolated or high-impedanceearthed power systems.
Ordering of VT inputs inside of the busbarprotection IED will allow integration of voltagerelated functionality like under-voltage release,residual over-voltage, power functions, meteringand voltage recording during the faults. Howeverattention shall be given to the fact that inclusionof VT inputs will reduce number of available CTinputs (in total 24 analogue inputs are the productlimit). Consequently when VT inputs are orderedthe busbar protection IED will be applicable forbuses with a fewer number of bays. Practicallythe number of available CT inputs will limit thesize of the station which can be protected.
REB670 has very low requirements on the maincurrent transformers (that is, CTs) and nointerposing current transformers are necessary.For all applications, it is possible to include andmix main CTs with 1A and 5A rated secondarycurrent within the same protection zone.Typically, CTs with up to 10:1 ratio difference canbe used within the same differential protectionzone. Adjustment for different main CT ratios isachieved numerically by a parameter setting.
The numerical, low-impedance differentialprotection function is designed for fast andselective protection for faults within protectedzone. All connected CT inputs are provided with arestraint feature. The minimum pick-up value forthe differential current is set to give a suitablesensitivity for all internal faults. For busbarprotection applications typical setting value forthe minimum differential operating current is from50% to 150% of the biggest CT. This setting ismade directly in primary amperes. The operatingslope for the differential operating characteristic isfixed to 53% in the algorithm.
The fast tripping time of the low-impedancedifferential protection function is especiallyadvantageous for power system networks withhigh fault levels or where fast fault clearance isrequired for power system stability.
The advanced open CT detection algorithmdetects instantly the open CT secondary circuitsand prevents differential protection operationwithout any need for additional check zone.
Differential protection zones in REB670 include asensitive operational level. This sensitiveoperational level is designed to be able to detectinternal busbar earth faults in low impedanceearthed power systems (that is, power systemswhere the earth-fault current is limited to a certainlevel, typically between 300A and 2000A primaryby a neutral point reactor or resistor). Alternativelythis sensitive level can be used when highsensitivity is required from busbar differentialprotection (that is, energizing of the bus via longline).
Overall operating characteristic of the differentialfunction in REB670 is shown in figure 1.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2 Issued: December 2012
Revision: C
ABB 3
Differential protectionoperation characteristic
Operateregion
Diff Oper Level
I d [P
rimar
y Am
ps]
Iin [Primary Amps]
s=0.53
I d=I in
Sensitivedifferentialprotection
en06000142.vsd
Sensitive Oper Level Sens Iin Block
IEC06000142 V1 EN
Figure 1. REB670 operating characteristic
Integrated overall check zone feature,independent from any disconnector position, isavailable. It can be used in double busbar stationsto secure stability of the busbar differentialprotection in case of entirely wrong statusindication of busbar disconnector in any of thefeeder bays.
Flexible, software based dynamic Zone Selectionenables easy and fast adaptation to the mostcommon substation arrangements such as singlebusbar with or without transfer bus, doublebusbar with or without transfer bus, one-and-a-half breaker stations, double busbar-doublebreaker stations, ring busbars, and so on. Thesoftware based dynamic Zone Selections ensures:
• Dynamic linking of measured CT currents tothe appropriate differential protection zoneas required by substation topology
• Efficient merging of the two differential zoneswhen required by substation topology (that isload-transfer)
• Selective operation of busbar differentialprotection ensures tripping only of circuitbreakers connected to the faulty zone
• Correct marshaling of backup-tripcommands from internally integrated or
external circuit breaker failure protections toall surrounding circuit breakers
• Easy incorporation of bus-section and/or bus-coupler bays (that is, tie-breakers) with oneor two sets of CTs into the protection scheme
• Disconnector and/or circuit breaker statussupervision
Advanced Zone Selection logic accompanied byoptionally available end-fault and/or circuitbreaker failure protections ensure minimumpossible tripping time and selectivity for faultswithin the blind spot or the end zone between bayCT and bay circuit breaker. Therefore REB670offers best possible coverage for such faults infeeder and bus-section/bus-coupler bays.
Optionally available circuit breaker failureprotection, one for every CT input into REB670,offers secure local back-up protection for thecircuit breakers in the station.
Optionally available four-stage, non-directionalovercurrent protections, one for every CT inputinto REB670, provide remote backup functionalityfor connected feeders and remote-end stations.
Optionally available voltage and frequencyprotection functions open possibility to include
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
4 ABB
voltage release criterion for busbar protection orto integrate independent over-, under-voltageprotection for the bus in the busbar protectionIED.
Optionally available over-current, thermal overloadand capacitor bank protection functions openpossibilities to integrate protection of shuntreactors and shunt capacitor banks into thebusbar protection IED.
It is normal practice to have just one busbarprotection IED per busbar. Nevertheless someutilities do apply two independent busbarprotection IEDs per zone of protection. REB670IED fits both solutions.
A simplified bus differential protection for multi-phase faults and earth faults can be obtained byusing a single, one-phase REB670 IED withexternal auxiliary summation current transformers.
The wide application flexibility makes this productan excellent choice for both new installations andthe refurbishment of existing installations.
Optional apparatus control for up to 30 objectscan provide a facility to draw simplified single linediagram (SLD) of the station on the local HMI.Note that in such case medium-size, graphicdisplay shall be ordered.
Application examples of REB670Examples of typical station layouts, which can beprotected with REB670 are given below:
IEC11000237-1-en.vsdIEC11000237 V1 EN
Figure 2. Example of T-connection
BI1 BI1 BI1 BI1 BI1 BI1 BI1
QA1 QA1 QA1 QA1 QA1 QA1 QA1
QB1ZA ZB
IEC11000238-1-en.vsdIEC11000238 V1 EN
Figure 3. Example of single bus station
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 5
BI1
QA1
QB1 QB7
BI1
QB7QB1
QA1
BI1
QB7QB1
QA1
BI1
QB7QB1
QA1
BI1
QB7QB1
QA1
ZA
ZB
BI1
QB7QB1
QA1
xx06000013.vsdIEC06000013 V1 EN
Figure 4. Example of single bus station with transfer bus
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2BI1
QA1
BI1
QB1 QB2
QA1
ZA
ZB
IEC11000239-1-en.vsdIEC11000239 V1 EN
Figure 5. Example of double bus-single breaker station
BI1
QB1 QB2 QB7
BI1
QB1 QB2 QB7
BI1
QB1 QB2 QB7
BI1
QB1 QB2 QB7
BI1
QB20QB2 QB7QB1
QA1 QA1 QA1 QA1 QA1
ZAZB
xx06000015.vsdIEC06000015 V1 EN
Figure 6. Example of double bus-single breaker station with transfer bus
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
6 ABB
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2
BI1
QA1
QB1 QB2BI1
QA1
BI1 QA1
BI1 QA1
BI1
QB1 QB2
QA1
BI1
QA1
ZA1
ZB1
ZA2
ZB2
xx06000016.vsd
IEC06000016 V1 EN
Figure 7. Example of double bus-single breaker station with two bus-section and two bus-coupler breakers
BI3
BI1
QA1
BI2
QA2
QA3
BI3
BI1
QA1
BI2
QA2
QA3
BI3
BI1
QA1
BI2
QA2
QA3
BI3
BI1
QA1
BI2
QA2
QA3
BI3
BI1
QA1
BI2
QA2
QA3
ZA
ZB
IEC11000240-1-en.vsdIEC11000240 V1 EN
Figure 8. Example of one-and-a-half breaker station
QA1
BI1 BI2
QA2 QA1
BI1 BI2
QA2 QA1
BI1 BI2
QA2 QA1
BI1 BI2
QA2 QA1
BI1 BI2
QA2
ZA
ZB
xx06000018.vsdIEC06000018 V1 EN
Figure 9. Example of double bus-double breaker station
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 7
QB32
QB12BI1
QA3BI3
BI8
QA4
BI4
QA2
BI2
BI5
BI6BI7
QB5QB8
QB6QB7
QB31
QB11
QB42 QB22
QB21QB41
QA1ZA1 ZA2
ZB1 ZB2
xx06000019.vsdIEC06000019 V1 EN
Figure 10. Example of mesh or ring bus station
Note that customized REB670 is delivered without any configuration. Thus the complete IEDengineering shall be done by the customer or its system integrator. In order to secure properoperation of the busbar protection it is strictly recommended to always start engineering work fromthe PCM600 project for the pre-configured REB670 which is the closest to the actual application.Then, necessary modifications shall be applied in order to adopt the customized IED configurationto suite the actual station layout. The PCM600 project for the pre-configured REB670 IEDs isavailable in the Connectivity Package DVD.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
8 ABB
2. Available functions
Main protection functions
2 = number of basic instances0-3 = option quantities
IEC 61850 ANSI Function description Busbar
REB670
Differential protection
BUTPTRC,BCZTPDIF,BZNTPDIF,BZITGGIO
87B Busbar differential protection, 2 zones, three phase/up to 8 bays 0-1
BUSPTRC,BCZSPDIF,BZNSPDIF,BZISGGIO
87B Busbar differential protection, 2 zones, single phase/up to 24 bays 0-1
SWSGGIO Status of primary switching object for busbar protection zoneselection
96
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 9
Back-up protection functions
IEC 61850 ANSI Function description Busbar
REB670
Current protection
OC4PTOC 51_67 Four step phase overcurrent protection 0-8
PH4SPTOC 51 Four step single phase overcurrent protection 0-24
TRPTTR 49 Thermal overload protection, two time constant 0-2
CCRBRF 50BF Breaker failure protection 0-8
CCSRBRF 50BF Breaker failure protection, single phase version 0-24
GUPPDUP 37 Directional underpower protection 0-4
GOPPDOP 32 Directional overpower protection 0-4
CBPGAPC Capacitor bank protection 0-2
Voltage protection
UV2PTUV 27 Two step undervoltage protection 0-2
OV2PTOV 59 Two step overvoltage protection 0-2
ROV2PTOV 59N Two step residual overvoltage protection 0-2
VDCPTOV 60 Voltage differential protection 0-2
LOVPTUV 27 Loss of voltage check 0-2
Frequency protection
SAPTUF 81 Underfrequency protection 0-6
SAPTOF 81 Overfrequency protection 0-6
SAPFRC 81 Rate-of-change frequency protection 0-6
Multipurpose protection
CVGAPC General current and voltage protection 0-6
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
10 ABB
Control and monitoring functions
IEC 61850 ANSI Function description Busbar
REB670
Control
SMBRREC 79 Autorecloser 0-2
APC30 3 Apparatus control for up to 6 bays, max 30 apparatuses (6CBs)incl. interlocking
0-1
QCBAY Apparatus control 1
LocalRemote
Handling of LRswitch positions 1
LocRemControl
LHMI control of PSTO 1
SLGGIO Logic rotating switch for function selection and LHMI presentation 15
VSGGIO Selector mini switch 20
DPGGIO IEC61850 generic communication I/O functions 16
SPC8GGIO Single pole generic control 8 signals 5
AutomationBits AutomationBits, command function for DNP3.0 3
Single command, 16 signals 4
Secondary system supervision
SDDRFUF Fuse failure supervision 0-2
Logic
Configuration logic blocks 40-280
Fixed signal function blocks 1
B16I Boolean 16 to Integer conversion 16
B16IFCVI Boolean 16 to Integer conversion with Logic Node representation 16
IB16 Integer to Boolean 16 conversion 16
IB16FVCB Integer to Boolean 16 conversion with Logic Node representation 16
Monitoring
CVMMXN Measurements 6
CNTGGIO Event counter 5
Event Event function 20
DRPRDRE Disturbance report 1
SPGGIO IEC61850 generic communication I/O functions 64
SP16GGIO IEC61850 generic communication I/O functions 16 inputs 16
MVGGIO IEC61850 generic communication I/O functions 24
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 11
IEC 61850 ANSI Function description Busbar
REB670
BSStartReport
Logical signal status report 3
RANGE_XP Measured value expander block 28
Metering
PCGGIO Pulse-counter logic 16
ETPMMTR Function for energy calculation and demand handling 6
Designed to communicate
IEC 61850 ANSI Function description Busbar
REB670
Station communication
SPA communication protocol 1
LON communication protocol 1
IEC60870-5-103 communication protocol 20/1
Operation selection between SPA and IEC60870-5-103 for SLM 1
DNP3.0 for TCP/IP and EIA-485 communication protocol 1
DNP3.0 fault records for TCP/IP and EIA-485 communicationprotocol
1
Parameter setting function for IEC61850 1
IntlReceive Horizontal communication via GOOSE for interlocking 59
Goose binary receive 10
Multiple command and transmit 60/10
Ethernet configuration of links 1
IEC 62439-3 Edition 1 parallel redundancy protocol 0-1
IEC 62439-3 Edition 2 parallel redundancy protocol 0-1
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
12 ABB
Basic IED functions
IEC 61850 Function description
Basic functions included in all products
IntErrorSig Self supervision with internal event list 1
TIME Time and synchronization error 1
TimeSynch Time synchronization 1
ActiveGroup Parameter setting groups 1
Test Test mode functionality 1
ChangeLock Change lock function 1
TerminalID IED identifiers 1
Productinfo Product information 1
MiscBaseCommon Misc Base Common 1
IEDRuntimeComp IED Runtime Comp 1
RatedFreq Rated system frequency 1
SMBI Signal Matrix for binary inputs 40
SMBO Signal Matrix for binary outputs 40
SMMI Signal Matrix for mA inputs 4
SMAI Signal Matrix for analog inputs 36
Sum3Ph Summation block 3 phase 18
LocalHMI Parameter setting function for HMI in PCM600 1
LocalHMI Local HMI signals 1
AuthStatus Authority status 1
AuthorityCheck Authority check 1
AccessFTP FTP access with password 1
SPACommMap SPA communication mapping 1
DOSFRNT Denial of service, frame rate control for front port 1
DOSOEMAB Denial of service, frame rate control for OEM port AB 1
DOSOEMCD Denial of service, frame rate control for OEM port CD 1
3. Differential protectionThe function consists of differential protectionalgorithm, sensitive differential protectionalgorithm, check zone algorithm, open CTalgorithm and two supervision algorithms.
Busbar differential protectionThis protection function is intended for fast andselective tripping of faults within protected zone.For each current input, the CT ratio can be setfrom the front HMI or via the parameter-settingtool, PCM600. In this way adaptation to differentCT ratios is provided in the simplest way. The
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 13
minimum pick-up value for the differential currentis then set to give a suitable sensitivity for allinternal faults. This setting is made directly inprimary amperes. For busbar protectionapplications typical setting value for the minimumdifferential operating current is from 50% to 150%of the biggest CT. The settings can be changedfrom the front HMI or via the parameter-settingtool, PCM600.
All current inputs are indirectly provided with arestraint feature. The operation is based on thewell-proven RADSS percentage restraintstabilization principle, with an extra stabilizationfeature to stabilize for very heavy CT saturation.Stability for external faults is guaranteed if a CT isnot saturated for at least two milliseconds duringeach power system cycle. It is also possible toadd external tripping criteria by binary signal.
The trip command from the differential protectionincluding sensitive differential protection andcircuit breaker failure backup-trip commands canbe set either as self-resetting or latched. Insecond case the manual reset is needed in orderto reset the individual bay trip output contacts.
Sensitive differential level BZISGGIODifferential protection zones in REB670 include asensitive operational level. This sensitiveoperational level is designed to be able to detectinternal busbar earth faults in low impedanceearthed power systems (i.e. power systems wherethe earth-fault current is limited to a certain level,typically between 300A and 2000A primary by aneutral point reactor or resistor). For increasedsecurity, the sensitive differential protection mustbe externally enabled by a binary signal (e.g. fromopen delta VT overvoltage relay or powertransformer neutral point overcurrent relay). Finallyit is as well possible to set a time delay before thetrip signal from the sensitive differential protectionis given. This sensitive level can be alternativelyused in special applications when high sensitivityis required from busbar differential protection (i.e.energizing of dead bus via a long line).
Operation and operating characteristic of thesensitive differential protection can be setindependently from the operating characteristic ofthe main differential protection. However, thesensitive differential level is blocked as soon asthe total incoming current exceeds the pre-set
level or when differential current exceed the setminimum pickup current for the usual differentialprotection. Therefore, by appropriate settings itcan be ensured that this sensitive level is blockedfor all external multi-phase faults, which cancause CT saturation. Operating characteristic ofsensitive differential characteristics is shown infigure 1.
Check zoneFor busbar protection in double busbar stationswhen dynamic zone selection is needed, it issometimes required to include the overalldifferential zone (that is, check zone). Hence, thebuilt-in, overall check zone is available in the IED.Because the built-in check zone currentmeasurement is not dependent on thedisconnector status, this feature ensures stabilityof Busbar differential protection even forcompletely wrong status indication from thebusbar disconnectors. It is to be noted that theoverall check zone, only supervise the usualdifferential protection operation. The external tripcommands, breaker failure backup-tripcommands and sensitive differential protectionoperation are not supervised by the overall checkzone.
The overall check zone has simple currentoperating algorithm, which ensures check zoneoperation for all internal faults regardless the faultcurrent distribution. To achieve this, the outgoingcurrent from the overall check zone is used asrestraint quantity. If required, the check zoneoperation can be activated externally by a binarysignal.
Open CT detectionThe innovative measuring algorithm providesstability for open or short-circuited main CTsecondary circuits, which means that no separatecheck zone is actually necessary. Start currentlevel for open CT detection can usually be set todetect the open circuit condition for the smallestCT. This built-in feature allows the protectionterminal to be set very sensitive, even to a lowervalue than the maximum CT primary rating in thestation. At detection of problems in CT secondarycircuits, the differential protection can be instantlyblocked and an alarm is given. Alternatively, thedifferential protection can be automaticallydesensitized in order to ensure busbar differentialprotection stability during normal through-load
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
14 ABB
condition. When problems in CT secondarycircuits have been found and associated error hasbeen corrected a manual reset must be given tothe IED. This can be done locally from the localHMI, or remotely via binary input orcommunication link.
However, it is to be noted that this feature canonly be partly utilized when the summationprinciple is in use.
Differential protection supervisionDual monitoring of differential protection status isavailable. The first monitoring feature operatesafter settable time delay when differential currentis higher than the user settable level. This featurecan be, for example, used to design automaticreset logic for previously described open CTdetection feature. The second monitoring featureoperates immediately when the busbar through-going current is bigger than the user settablelevel. Both of these monitoring features are phasesegregated and they give out binary signals,which can be either used to trigger disturbancerecorder or for alarming purposes.
4. Zone selectionTypically CT secondary circuits from every bay inthe station are connected to the busbarprotection. The built-in software feature called“Zone Selection” gives a simple but efficientcontrol over the connected CTs to busbarprotection IED in order to provide fully operationaldifferential protection scheme for multi-zoneapplications on both small and large buses.
The function consists of dedicated disconnector/circuit breaker status monitoring algorithm, baydedicated CT-connection control algorithm andzone interconnection algorithm.
Switch status monitoringFor stations with complex primary layout (that is,double busbar single breaker station with orwithout transfer bus) the information about busbardisconnector position in every bay is crucialinformation for busbar protection. The positions ofthese disconnectors then actually determinewhich CT input (that is, bay) is connected towhich differential protection zone. For some moreadvanced features like end-fault or blind-spotprotection the actual status of the circuit breakerin some or even all bays can be vital information
for busbar protection as well. The switch functionblock is used to take the status of two auxiliarycontacts from the primary device, evaluate themand then to deliver the device primary contactposition to the rest of the zone selection logic.
For such applications typically two auxiliarycontacts (that is, normally open and normallyclosed auxiliary contacts) from each relevantprimary switching object shall be connected tothe IED. Then the status for every individualprimary switching object will be determined. Thededicated function block for each primaryswitching object is available in order to determinethe status of the object primary contacts. By aparameter setting one of the following two logicalschemes can be selected for each primary objectindividually by the end user:
• If not open then closed (that is, as in RADSSschemes)
• Open or closed only when clearly indicatedby aux contact status (that is, as in INXschemes)
Table 1 gives quick overview about both schemes.
Note that the first scheme only requires fastbreaking normally closed auxiliary contact (that is,b contact) for proper operation. The timing ofnormally open auxiliary contact is not criticalbecause it is only used for supervision of theprimary object status. The second scheme inaddition requires properly timed-adjusted, early-making normally open auxiliary contact (that is,early making a contact) for proper operation.
Regardless which scheme is used the time-delayed disconnector/circuit breaker statussupervision alarm is available (that is, 00 or 11auxiliary contact status). How two integrateddifferential protection zones behave whendisconnector alarm appears is freely configurableby the end user.
It is possible by a parameter setting to overridethe primary object status as either permanentlyopen or permanently closed. This feature can beuseful during testing, installation andcommissioning of the busbar protection scheme.At the same time, separate alarm is given toindicate that the actual object status isoverwritten by a setting parameter.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 15
It is to be noted that it is as well possible to useonly normally closed auxiliary contacts for Zone
Selection logic. In that case the Switch functionblocks are not used.
Table 1. Treatment of primary object auxiliary contact status
Primary equipment Status in busbar protection Alarm facility
Normally Openauxiliarycontact status(that is,“closed” or“a” contact)
NormallyClosedauxiliarycontact status(that is,“open” or “b”contact)
when“Scheme 1RADSS”is selected
when“Scheme 2INX”is selected
Alarm aftersettable timedelay
Information visible on localHMI
open open closed Last positionsaved
yes intermediate_00
open
closed open open no open
closed
open closed closed no closed
closed closed closed closed yes badState_11
BayEach CT input is allocated to one dedicated bayfunction block. This function block is used toprovide complete user interface for all signalsfrom and towards this bay. It is also used toinfluence bay measured current.
It is possible by a parameter settingCTConnection to connect or disconnect the CTinput to the bay function block. Once the CT inputis connected to the bay function block thisassociated current input can be included to orexcluded from the two internally availabledifferential functions in software. This can bedone by a parameter setting for simple stationlayouts (that is, one-and-a-half breaker stations)or alternatively via dedicated logical scheme (thatis, double busbar stations). For each bay the enduser have to select one of the following fivealternatives:
• Permanently connect this bay current tozone A (that is, ZA)
• Permanently connect this bay current tozone B (that is, ZB)
• Permanently connect this bay current tozone A and inverted bay current to ZB (thatis, ZA and ZB)
• Connect this bay current to ZA or ZBdepending on the logical status of the two
input binary signals available on this bayfunction block. These two input signals willinclude measured current to the respectivezone when their logical value is one (that is,CntrlIncludes). This option is used togetherwith above described Switch function blocksin order to provide complete Zone Selectionlogic
• Connect the bay current to ZA or ZBdepending on the logical status of the twoinput binary signals available on this bayfunction block. These two signals will includemeasured current to the respective zonewhen their logical value is zero (that is,CntrlExcludes). This option is typically usedwhen only normally closed auxiliary contactsfrom the busbar disconnector are availableto the Zone Selection logic
At the same time, an additional feature forinstantaneous or time delayed disconnection oreven inversion of the connected bay current viaseparate logical signals is also available. Thisfeature is provided in order to facilitate for bus-section or bus-coupler CT disconnection for tie-breakers with a CT only on one side of the circuitbreaker. This ensures correct and fast faultclearance of faults between the CT and the circuitbreaker within these bays. The same feature canbe individually used in any feeder bay to optimizeBusbar differential protection performance, when
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
16 ABB
feeder circuit breaker is open. Thus, the end-faultprotection for faults between circuit breaker andthe CT is available. However, to use this featurecircuit breaker auxiliary contacts and closingcommand to the circuit breaker shall be wired tothe binary inputs of the IED. Therefore, he IEDoffers best possible coverage for these specialfaults between CT and circuit breaker in feederand bus-section/bus-coupler bays.
Within the Bay function block it is decided by aparameter setting how this bay should behaveduring zone interconnection (that is, loadtransfer). For each bay individually one of thefollowing three options can be selected:
• Bay current is forced out from both zonesduring zone interconnection (used for bus-coupler bays)
• Bay current is unconditionally forced intoboth zones during zone interconnection(used in special applications)
• Bay current is connected to both zonesduring zone interconnection if the bay waspreviously connected to one of the twozones (typically used for feeder bays)
The third option ensures that the feeder, which isout of service, is not connected to any of the twozones during zone interconnection.
Within the Bay function block it is decided by aparameter setting whether this bay should beconnected to the check zone or not. In this waythe end user has simple control over the bays,which shall be connected to the overall checkzone.
By appropriate configuration logic it is possible totake any bay (that is, CT input) out of service. Thiscan be done from the local HMI or externally viabinary signal. In that case all internal currentmeasuring functions (that is, differentialprotection, sensitive differential protection, check
zone, breaker failure protection and overcurrentprotection) are disabled. At the same time, anytrip command to this bay circuit breaker can beinhibited.
Via two dedicated binary input signals it ispossible to:
• Trip only the bay circuit breaker (used forintegrated OC protection tripping)
• Trip the whole differential zone to which thisbay is presently connected (used for backup-trip command from either integrated orexternal bay circuit breaker failure protection)
Finally dedicated trip binary output from the Bayfunction block is available in order to providecommon trip signal to the bay circuit breaker frombusbar differential protection, breaker failureprotection, backup overcurrent protection and soon.
In this way the interface to the user is kept assimple as possible and IED engineering work isquite straight forward.
Zone interconnection (Load transfer)When this feature is activated the two integrateddifferential protection zones are merged into onecommon, overall differential zone. This feature isrequired in double busbar stations when in any ofthe feeder bays both busbar disconnectors areclosed at the same time (that is, load transfer). Asexplained in above section Bay each CT input willthen behave in the pre-set way in order to ensureproper current balancing during this specialcondition. This feature can be startedautomatically (when Zone Selection logicdetermines that both busbar disconnectors in onefeeder bay are closed at the same time) orexternally via dedicated binary signal. If thisfeature is active for longer time than the pre-setvale the alarm signal is given.
5. Current protection
Four step phase overcurrent protection OC4PTOCThe four step phase overcurrent protectionfunction OC4PTOC has an inverse or definite timedelay independent for step 1 and 4 separately.Step 2 and 3 are always definite time delayed.
All IEC and ANSI inverse time characteristics areavailable together with an optional user definedtime characteristic.
The directional function is voltage polarized withmemory. The function can be set to be directional
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 17
or non-directional independently for each of thesteps.
A 2nd harmonic blocking can be set individuallyfor each step.
This function can be used as a backup bayprotection (e.g. for transformers, reactors, shuntcapacitors and tie-breakers). A special applicationis to use this phase overcurrent protection todetect short-circuits between the feeder circuitbreaker and feeder CT in a feeder bay when thecircuit breaker is open. This functionality is calledend-fault protection. In such case unnecessarilyoperation of the busbar differential protection canbe prevented and only fast overcurrent trip signalcan be sent to the remote line end. In order toutilize this functionality the circuit breaker statusand CB closing command must be connected tothe REB670. One of the overcurrent steps can beset and configured to act as end-fault protectionin REB670.
Four step single phase overcurrent protectionPH4SPTOCFour step single phase overcurrent protection(PH4SPTOC)has an inverse or definite time delayindependent for each step separately.
All IEC and ANSI time delayed characteristics areavailable together with an optional user definedtime characteristic.
The function is normally used as end faultprotection to clear faults between currenttransformer and circuit breaker.
Thermal overload protection, two time constantTRPTTRIf a power transformer or generator reaches veryhigh temperatures the equipment might bedamaged. The insulation within the transformer/generator will have forced ageing. As aconsequence of this the risk of internal phase-to-phase or phase-to-earth faults will increase. Hightemperature will degrade the quality of thetransformer/generator insulation.
The thermal overload protection estimates theinternal heat content of the transformer/generator(temperature) continuously. This estimation ismade by using a thermal model of the transformer/generator with two time constants, which isbased on current measurement.
Two warning levels are available. This enablesactions in the power system to be done beforedangerous temperatures are reached. If thetemperature continues to increase to the tripvalue, the protection initiates a trip of theprotected transformer/generator.
Breaker failure protection CCRBRFBreaker failure protection (CCRBRF) ensures fastback-up tripping of surrounding breakers in casethe own breaker fails to open. CCRBRF can becurrent based, contact based, or an adaptivecombination of these two conditions.
Current check with extremely short reset time isused as check criterion to achieve high securityagainst unnecessary operation.
Contact check criteria can be used where thefault current through the breaker is small.
CCRBRF can be single- or three-phase initiatedto allow use with single phase trippingapplications. For the three-phase version ofCCRBRF the current criteria can be set to operateonly if two out of four for example, two phases orone phase plus the residual current start. Thisgives a higher security to the back-up tripcommand.
CCRBRF function can be programmed to give asingle- or three-phase re-trip of the own breakerto avoid unnecessary tripping of surroundingbreakers at an incorrect initiation due to mistakesduring testing.
Breaker failure protection, single phase versionCCSRBRFBreaker failure protection, single phase version(CCSRBRF) function ensures fast back-uptripping of surrounding breakers.
A current check with extremely short reset time isused as check criteria to achieve a high securityagainst unnecessary operation.
CCSRBRF can be programmed to give a re-trip ofthe own breaker to avoid unnecessary tripping ofsurrounding breakers at an incorrect starting dueto mistakes during testing.
Directional over/underpower protectionGOPPDOP/GUPPDUPThe directional over-/under-power protectionGOPPDOP/GUPPDUP can be used wherever a
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
18 ABB
high/low active, reactive or apparent powerprotection or alarming is required. The functionscan alternatively be used to check the direction ofactive or reactive power flow in the power system.There are a number of applications where suchfunctionality is needed. Some of them are:
• detection of reversed active power flow• detection of high reactive power flow
Each function has two steps with definite timedelay. Reset times for both steps can be set aswell.
Capacitor bank protection (CBPGAPC)Shunt Capacitor Banks (SCB) are used in a powersystem to provide reactive power compensationand power factor correction. They are as wellused as integral parts of Static Var Compensators(SVC) or Harmonic Filters installations. Capacitorbank protection (CBPGAPC) function is speciallydesigned to provide protection and supervisionfeatures for SCBs.
6. Voltage protection
Two step undervoltage protection UV2PTUVUndervoltages can occur in the power systemduring faults or abnormal conditions. Two stepundervoltage protection (UV2PTUV) function canbe used to open circuit breakers to prepare forsystem restoration at power outages or as long-time delayed back-up to primary protection.
UV2PTUV has two voltage steps, each withinverse or definite time delay.
Two step overvoltage protection OV2PTOVOvervoltages may occur in the power systemduring abnormal conditions such as suddenpower loss, tap changer regulating failures, openline ends on long lines etc.
Two step overvoltage protection (OV2PTOV)function can be used to detect open line ends,normally then combined with a directional reactiveover-power function to supervise the systemvoltage. When triggered, the function will causean alarm, switch in reactors, or switch outcapacitor banks.
OV2PTOV has two voltage steps, each of themwith inverse or definite time delayed.
OV2PTOV has an extremely high reset ratio toallow settings close to system service voltage.
Two step residual overvoltage protectionROV2PTOVResidual voltages may occur in the power systemduring earth faults.
Two step residual overvoltage protectionROV2PTOV function calculates the residualvoltage from the three-phase voltage inputtransformers or measures it from a single voltageinput transformer fed from an open delta orneutral point voltage transformer.
ROV2PTOV has two voltage steps, each withinverse or definite time delay.
Reset delay ensures operation for intermittentearth faults.
Voltage differential protection VDCPTOVA voltage differential monitoring function isavailable. It compares the voltages from two threephase sets of voltage transformers and has onesensitive alarm step and one trip step.
Loss of voltage check LOVPTUVLoss of voltage check (LOVPTUV) is suitable foruse in networks with an automatic systemrestoration function. LOVPTUV issues a three-pole trip command to the circuit breaker, if allthree phase voltages fall below the set value for atime longer than the set time and the circuitbreaker remains closed.
7. Frequency protection
Underfrequency protection SAPTUFUnderfrequency occurs as a result of a lack ofgeneration in the network.
Underfrequency protection SAPTUF is used forload shedding systems, remedial action schemes,gas turbine startup and so on.
SAPTUF is also provided with undervoltageblocking.
The operation is based on positive sequencevoltage measurement and requires two phase-phase or three phase-neutral voltages to beconnected. For information about how to connect
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 19
analog inputs, refer to Application manual/IEDapplication/Analog inputs/Setting guidelines
Overfrequency protection SAPTOFOverfrequency protection function SAPTOF isapplicable in all situations, where reliabledetection of high fundamental power systemfrequency is needed.
Overfrequency occurs because of sudden loaddrops or shunt faults in the power network. Closeto the generating plant, generator governorproblems can also cause over frequency.
SAPTOF is used mainly for generation sheddingand remedial action schemes. It is also used as afrequency stage initiating load restoring.
SAPTOF is provided with an undervoltageblocking.
The operation is based on positive sequencevoltage measurement and requires two phase-phase or three phase-neutral voltages to beconnected. For information about how to connectanalog inputs, refer to Application manual/IEDapplication/Analog inputs/Setting guidelines
Rate-of-change frequency protection SAPFRCRate-of-change frequency protection function(SAPFRC) gives an early indication of a maindisturbance in the system. SAPFRC can be usedfor generation shedding, load shedding andremedial action schemes. SAPFRC candiscriminate between positive or negative changeof frequency.
SAPFRC is provided with an undervoltageblocking. The operation is based on positivesequence voltage measurement and requires twophase-phase or three phase-neutral voltages tobe connected. For information about how toconnect analog inputs, refer to Applicationmanual/IED application/Analog inputs/Settingguidelines.
8. Multipurpose protection
General current and voltage protection CVGAPCThe General current and voltage protection(CVGAPC) can be utilized as a negative or zerosequence current and/or voltage protection
detecting unsymmetrical conditions such as openphase or unsymmetrical faults.
9. Secondary system supervision
Fuse failure supervision SDDRFUFThe aim of the fuse failure supervision function(SDDRFUF) is to block voltage measuringfunctions at failures in the secondary circuitsbetween the voltage transformer and the IED inorder to avoid unwanted operations thatotherwise might occur.
The fuse failure supervision function basically hasthree different algorithms, negative sequence andzero sequence based algorithms and anadditional delta voltage and delta currentalgorithm.
The negative sequence detection algorithm isrecommended for IEDs used in isolated or high-impedance earthed networks. It is based on thenegative-sequence measuring quantities, a highvalue of voltage 3U2 without the presence of the
negative-sequence current 3I2.
The zero sequence detection algorithm isrecommended for IEDs used in directly or lowimpedance earthed networks. It is based on thezero sequence measuring quantities, a high valueof voltage 3U0 without the presence of the
residual current 3I0.
For better adaptation to system requirements, anoperation mode setting has been introducedwhich makes it possible to select the operatingconditions for negative sequence and zerosequence based function. The selection ofdifferent operation modes makes it possible tochoose different interaction possibilities betweenthe negative sequence and zero sequence basedalgorithm.
A criterion based on delta current and deltavoltage measurements can be added to the fusefailure supervision function in order to detect athree phase fuse failure, which in practice is moreassociated with voltage transformer switchingduring station operations.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
20 ABB
10. Control
Autorecloser SMBRRECThe autoreclosing function provides high-speedand/or delayed three pole autoreclosing. Theautoreclosing can be used for delayed busbarrestoration. One Autorecloser (SMBRREC) perzone can be made available.
Apparatus control APCThe apparatus control functions are used forcontrol and supervision of circuit breakers,disconnectors and earthing switches within a bay.Permission to operate is given after evaluation ofconditions from other functions such asinterlocking, synchrocheck, operator placeselection and external or internal blockings.
Apparatus control features:• Select-Execute principle to give high reliability• Selection function to prevent simultaneous
operation• Selection and supervision of operator place• Command supervision• Block/deblock of operation• Block/deblock of updating of position indications• Substitution of position indications• Overriding of interlocking functions• Overriding of synchrocheck• Operation counter• Suppression of Mid position
Two types of command models can be used:• Direct with normal security• SBO (Select-Before-Operate) with enhanced
security
In normal security, the command is processedand the resulting position is not supervised.However with enhanced security, the command isprocessed and the resulting position is supervised.
Normal security means that only the command isevaluated and the resulting position is notsupervised. Enhanced security means that thecommand is evaluated with an additionalsupervision of the status value of the controlobject. The command security with enhancedsecurity is always terminated by aCommandTermination service primitive.
Control operation can be performed from thelocal HMI under authority control if so defined.
Logic rotating switch for function selection andLHMI presentation SLGGIOThe logic rotating switch for function selectionand LHMI presentation (SLGGIO) (or the selectorswitch function block) is used to get a selectorswitch functionality similar to the one provided bya hardware selector switch. Hardware selectorswitches are used extensively by utilities, in orderto have different functions operating on pre-setvalues. Hardware switches are however sourcesfor maintenance issues, lower system reliabilityand an extended purchase portfolio. The logicselector switches eliminate all these problems.
Selector mini switch VSGGIOThe Selector mini switch VSGGIO function blockis a multipurpose function used for a variety ofapplications, as a general purpose switch.
VSGGIO can be controlled from the menu or froma symbol on the single line diagram (SLD) on thelocal HMI.
IEC 61850 generic communication I/O functionsDPGGIOThe IEC 61850 generic communication I/Ofunctions (DPGGIO) function block is used tosend double indications to other systems orequipment in the substation. It is especially usedin the interlocking and reservation station-widelogics.
Single point generic control 8 signals SPC8GGIOThe Single point generic control 8 signals(SPC8GGIO) function block is a collection of 8single point commands, designed to bring incommands from REMOTE (SCADA) to those partsof the logic configuration that do not needextensive command receiving functionality (forexample, SCSWI). In this way, simple commandscan be sent directly to the IED outputs, withoutconfirmation. Confirmation (status) of the result ofthe commands is supposed to be achieved byother means, such as binary inputs and SPGGIOfunction blocks. The commands can be pulsed orsteady.
AutomationBits, command function for DNP3.0AUTOBITSAutomationBits function for DNP3 (AUTOBITS) isused within PCM600 to get into the configurationof the commands coming through the DNP3protocol. The AUTOBITS function plays the same
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 21
role as functions GOOSEBINRCV (for IEC 61850)and MULTICMDRCV (for LON).
Single command, 16 signalsThe IEDs can receive commands either from asubstation automation system or from the localHMI. The command function block has outputsthat can be used, for example, to control highvoltage apparatuses or for other user definedfunctionality.
11. Logic
Configurable logic blocksA number of logic blocks and timers are availablefor the user to adapt the configuration to thespecific application needs.
• OR function block.
• INVERTER function blocks that inverts the inputsignal.
• PULSETIMER function block can be used, forexample, for pulse extensions or limiting ofoperation of outputs, settable pulse time.
• GATE function block is used for whether or nota signal should be able to pass from the inputto the output.
• XOR function block.
• LOOPDELAY function block used to delay theoutput signal one execution cycle.
• TIMERSET function has pick-up and drop-outdelayed outputs related to the input signal. Thetimer has a settable time delay.
• AND function block.
• SRMEMORY function block is a flip-flop thatcan set or reset an output from two inputsrespectively. Each block has two outputs whereone is inverted. The memory setting controls ifthe block's output should reset or return to thestate it was, after a power interruption. Setinput has priority.
• RSMEMORY function block is a flip-flop thatcan reset or set an output from two inputsrespectively. Each block has two outputs whereone is inverted. The memory setting controls ifthe block's output should reset or return to the
state it was, after a power interruption. RESETinput has priority.
Fixed signal function blockThe Fixed signals function (FXDSIGN) generates anumber of pre-set (fixed) signals that can be usedin the configuration of an IED, either for forcingthe unused inputs in other function blocks to acertain level/value, or for creating certain logic.
12. Monitoring
Measurements CVMMXN, CMMXU, VNMMXU,VMMXU, CMSQI, VMSQIThe measurement functions are used to get on-line information from the IED. These servicevalues make it possible to display on-lineinformation on the local HMI and on theSubstation automation system about:
• measured voltages, currents, frequency,active, reactive and apparent power andpower factor
• measured currents• primary and secondary phasors• positive, negative and zero sequence
currents and voltages• mA, input currents• pulse counters
Supervision of mA input signalsThe main purpose of the function is to measureand process signals from different measuringtransducers. Many devices used in processcontrol represent various parameters such asfrequency, temperature and DC battery voltage aslow current values, usually in the range 4-20 mAor 0-20 mA.
Alarm limits can be set and used as triggers, e.g.to generate trip or alarm signals.
The function requires that the IED is equippedwith the mA input module.
Event counter CNTGGIOEvent counter (CNTGGIO) has six counters whichare used for storing the number of times eachcounter input has been activated.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
22 ABB
Disturbance report DRPRDREComplete and reliable information aboutdisturbances in the primary and/or in thesecondary system together with continuous event-logging is accomplished by the disturbance reportfunctionality.
Disturbance report DRPRDRE, always included inthe IED, acquires sampled data of all selectedanalog input and binary signals connected to thefunction block with a, maximum of 40 analog and96 binary signals.
The Disturbance report functionality is a commonname for several functions:
• Event list• Indications• Event recorder• Trip value recorder• Disturbance recorder
The Disturbance report function is characterizedby great flexibility regarding configuration, startingconditions, recording times, and large storagecapacity.
A disturbance is defined as an activation of aninput to the AxRADR or BxRBDR function blocks,which are set to trigger the disturbance recorder.All signals from start of pre-fault time to the endof post-fault time will be included in the recording.
Every disturbance report recording is saved in theIED in the standard Comtrade format. The sameapplies to all events, which are continuouslysaved in a ring-buffer. The local HMI is used toget information about the recordings. Thedisturbance report files may be uploaded toPCM600 for further analysis using the disturbancehandling tool.
Event list DRPRDREContinuous event-logging is useful for monitoringthe system from an overview perspective and is acomplement to specific disturbance recorderfunctions.
The event list logs all binary input signalsconnected to the Disturbance report function. Thelist may contain up to 1000 time-tagged eventsstored in a ring-buffer.
Indications DRPRDRETo get fast, condensed and reliable informationabout disturbances in the primary and/or in thesecondary system it is important to know, forexample binary signals that have changed statusduring a disturbance. This information is used inthe short perspective to get information via thelocal HMI in a straightforward way.
There are three LEDs on the local HMI (green,yellow and red), which will display statusinformation about the IED and the Disturbancereport function (triggered).
The Indication list function shows all selectedbinary input signals connected to the Disturbancereport function that have changed status during adisturbance.
Event recorder DRPRDREQuick, complete and reliable information aboutdisturbances in the primary and/or in thesecondary system is vital, for example, time-tagged events logged during disturbances. Thisinformation is used for different purposes in theshort term (for example corrective actions) and inthe long term (for example functional analysis).
The event recorder logs all selected binary inputsignals connected to the Disturbance reportfunction. Each recording can contain up to 150time-tagged events.
The event recorder information is available for thedisturbances locally in the IED.
The event recording information is an integratedpart of the disturbance record (Comtrade file).
Trip value recorder DRPRDREInformation about the pre-fault and fault values forcurrents and voltages are vital for the disturbanceevaluation.
The Trip value recorder calculates the values of allselected analog input signals connected to theDisturbance report function. The result ismagnitude and phase angle before and during thefault for each analog input signal.
The trip value recorder information is available forthe disturbances locally in the IED.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 23
The trip value recorder information is anintegrated part of the disturbance record(Comtrade file).
Disturbance recorder DRPRDREThe Disturbance recorder function supplies fast,complete and reliable information aboutdisturbances in the power system. It facilitatesunderstanding system behavior and relatedprimary and secondary equipment during andafter a disturbance. Recorded information is usedfor different purposes in the short perspective (forexample corrective actions) and long perspective(for example functional analysis).
The Disturbance recorder acquires sampled datafrom selected analog- and binary signalsconnected to the Disturbance report function(maximum 40 analog and 96 binary signals). Thebinary signals available are the same as for theevent recorder function.
The function is characterized by great flexibilityand is not dependent on the operation ofprotection functions. It can record disturbancesnot detected by protection functions. Up to tenseconds of data before the trigger instant can besaved in the disturbance file.
The disturbance recorder information for up to100 disturbances are saved in the IED and thelocal HMI is used to view the list of recordings.
Event functionWhen using a Substation Automation system withLON or SPA communication, time-tagged eventscan be sent at change or cyclically from the IEDto the station level. These events are created fromany available signal in the IED that is connectedto the Event function (EVENT). The event functionblock is used for LON and SPA communication.
Analog and double indication values are alsotransferred through EVENT function.
IEC61850 generic communication I/O functionsMVGGIOIEC61850 generic communication I/O functions(MVGGIO) function is used to send theinstantaneous value of an analog signal to othersystems or equipment in the substation. It canalso be used inside the same IED, to attach aRANGE aspect to an analog value and to permitmeasurement supervision on that value.
Measured value expander block RANGE_XPThe current and voltage measurements functions(CVMMXN, CMMXU, VMMXU and VNMMXU),current and voltage sequence measurementfunctions (CMSQI and VMSQI) and IEC 61850generic communication I/O functions (MVGGIO)are provided with measurement supervisionfunctionality. All measured values can besupervised with four settable limits: low-low limit,low limit, high limit and high-high limit. Themeasure value expander block (RANGE_XP) hasbeen introduced to enable translating the integeroutput signal from the measuring functions to 5binary signals: below low-low limit, below lowlimit, normal, above high-high limit or above highlimit. The output signals can be used asconditions in the configurable logic or for alarmingpurpose.
13. Metering
Pulse counter logic PCGGIOPulse counter (PCGGIO) function countsexternally generated binary pulses, for instancepulses coming from an external energy meter, forcalculation of energy consumption values. Thepulses are captured by the binary input moduleand then read by the function. A scaled servicevalue is available over the station bus. The specialBinary input module with enhanced pulsecounting capabilities must be ordered to achievethis functionality.
Function for energy calculation and demandhandling ETPMMTROutputs from the Measurements (CVMMXN)function can be used to calculate energyconsumption. Active as well as reactive values arecalculated in import and export direction. Valuescan be read or generated as pulses. Maximumdemand power values are also calculated by thefunction.
14. Basic IED functions
Time synchronizationThe time synchronization source selector is usedto select a common source of absolute time forthe IED when it is a part of a protection system.This makes it possible to compare event and
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
24 ABB
disturbance data between all IEDs in a stationautomation system.
15. Human machine interface
Human machine interfaceThe local HMI is equipped with a LCD that is usedamong other things to locally display the followingcrucial information:
• Connection of each bay, respecting the twodifferential protection zones and the checkzone. In the Parameter Setting Tool the usersets individual bay names to facilitate theidentification of each primary bay for stationpersonnel.
• Status of each individual primary switchgeardevice, for example, open, closed, 00 asintermediate state and 11 as bad state. InPCM600 the user sets the individual primaryswitchgear object names to facilitate theidentification of each switchgear device forthe station personnel.
The local HMI is divided into zones with differentfunctionality.
• Status indication LEDs.• Alarm indication LEDs, which consist of 15
LEDs (6 red and 9 yellow) with user printablelabel. All LEDs are configurable fromPCM600.
• Liquid crystal display (LCD).• Keypad with push buttons for control and
navigation purposes, switch for selectionbetween local and remote control and reset.
• Isolated RJ45 communication port.
IEC06000143 V1 EN
Figure 11. Example of medium graphic HMI
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 25
IEC06000191 V1 EN
Figure 12. Bay to zone connection example
1 User settable bay name
2 Internally used bay FB
3 Connections to internal zones
IEC06000192 V1 EN
Figure 13. Example of status of primary switchgearobjects
1 User settable switchgear names
2 Switchgear object status
16. Station communication
OverviewEach IED is provided with a communicationinterface, enabling it to connect to one or manysubstation level systems or equipment, either onthe Substation Automation (SA) bus or SubstationMonitoring (SM) bus.
Following communication protocols are available:
• IEC 61850-8-1 communication protocol• LON communication protocol• SPA or IEC 60870-5-103 communication
protocol• DNP3.0 communication protocol
Theoretically, several protocols can be combinedin the same IED.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
26 ABB
IEC 61850-8-1 communication protocolThe IED is equipped with single or double opticalEthernet rear ports (order dependent) for IEC61850-8-1 station bus communication. The IEC61850-8-1 communication is also possible fromthe optical Ethernet front port. IEC 61850-8-1protocol allows intelligent electrical devices (IEDs)from different vendors to exchange informationand simplifies system engineering. Peer-to-peercommunication according to GOOSE is part ofthe standard. Disturbance files uploading isprovided.
Serial communication, LONExisting stations with ABB station bus LON canbe extended with use of the optical LONinterface. This allows full SA functionality includingpeer-to-peer messaging and cooperationbetween existing ABB IED's and the new IED 670.
SPA communication protocolA single glass or plastic port is provided for theABB SPA protocol. This allows extensions ofsimple substation automation systems but themain use is for Substation Monitoring SystemsSMS.
IEC 60870-5-103 communication protocolA single glass or plastic port is provided for theIEC60870-5-103 standard. This allows design ofsimple substation automation systems includingequipment from different vendors. Disturbancefiles uploading is provided.
DNP3.0 communication protocolAn electrical RS485 and an optical Ethernet portis available for the DNP3.0 communication. DNP3.0 Level 2 communication with unsolicited events,time synchronizing and disturbance reporting isprovided for communication to RTUs, Gatewaysor HMI systems.
Multiple command and transmitWhen 670 IED's are used in SubstationAutomation systems with LON, SPA orIEC60870-5-103 communication protocols theEvent and Multiple Command function blocks areused as the communication interface for verticalcommunication to station HMI and gateway andas interface for horizontal peer-to-peercommunication (over LON only).
IEC 62439-3 Parallel Redundant ProtocolRedundant station bus communication accordingto IEC 62439-3 Edition 1 and IEC 62439-3 Edition2 are available as options in 670 series IEDs. IEC62439-3 parallel redundant protocol is an optionalquantity and the selection is made at ordering.Redundant station bus communication accordingto IEC 62439-3 uses both port AB and port CDon the OEM module.
Select IEC 62439-3 Edition 1protocol at the time of orderingwhen an existing redundantstation bus DuoDriverinstallation is extended.Select IEC 62439-3 Edition 2protocol at the time of orderingfor new installations withredundant station bus.IEC 62439-3 Edition 1 is NOTcompatible with IEC 62439-3Edition 2.
17. Remote communication
Analog and binary signal transfer to remote endThree analog and eight binary signals can beexchanged between two IEDs. This functionality ismainly used for the line differential protection.However it can be used in other products as well.An IED can communicate with up to 4 remoteIEDs.
Binary signal transfer to remote end, 192 signalsIf the communication channel is used for transferof binary signals only, up to 192 binary signalscan be exchanged between two IEDs. Forexample, this functionality can be used to sendinformation such as status of primary switchgearapparatus or intertripping signals to the remoteIED. An IED can communicate with up to 4remote IEDs.
For REB670 primary apparatus position indicationcan be exchanged between the single phase IEDs.
Line data communication module, short rangeLDCMThe line data communication module (LDCM) isused for communication between the IEDssituated at distances <110 km or from the IED to
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 27
optical to electrical converter with G.703 or G.703E1 interface located on a distances <3 kmaway. The LDCM module sends and receivesdata, to and from another LDCM module. TheIEEE/ANSI C37.94 standard format is used.
18. Hardware description
Hardware modulesPower supply module PSMThe power supply module is used to provide thecorrect internal voltages and full isolation betweenthe terminal and the battery system. An internalfail alarm output is available.
Binary input module BIMThe binary input module has 16 optically isolatedinputs and is available in two versions, onestandard and one with enhanced pulse countingcapabilities on the inputs to be used with thepulse counter function. The binary inputs arefreely programmable and can be used for theinput of logical signals to any of the functions.They can also be included in the disturbancerecording and event-recording functions. Thisenables extensive monitoring and evaluation ofoperation of the IED and for all associatedelectrical circuits.
Binary output module BOMThe binary output module has 24 independentoutput relays and is used for trip output or anysignaling purpose.
Static binary output module SOMThe static binary output module has six fast staticoutputs and six change over output relays for usein applications with high speed requirements.
Binary input/output module IOMThe binary input/output module is used when onlya few input and output channels are needed. Theten standard output channels are used for tripoutput or any signaling purpose. The two highspeed signal output channels are used forapplications where short operating time isessential. Eight optically isolated binary inputscater for required binary input information.
mA input module MIMThe milli-ampere input module is used to interfacetransducer signals in the –20 to +20 mA rangefrom for example OLTC position, temperature or
pressure transducers. The module has sixindependent, galvanically separated channels.
Optical ethernet module OEMThe optical fast-ethernet module is used toconnect an IED to the communication buses (likethe station bus) that use the IEC 61850-8-1protocol (port A, B). The module has one or twooptical ports with ST connectors.
Serial and LON communication module SLM,supports SPA/IEC 60870-5-103, LON and DNP 3.0The serial and LON communication module (SLM)is used for SPA, IEC 60870-5-103, DNP3 andLON communication. The module has two opticalcommunication ports for plastic/plastic, plastic/glass or glass/glass. One port is used for serialcommunication (SPA, IEC 60870-5-103 andDNP3 port or dedicated IEC 60870-5-103 portdepending on ordered SLM module) and one portis dedicated for LON communication.
Line data communication module LDCMEach module has one optical port, one for eachremote end to which the IED communicates.
Alternative cards for Short range (850 nm multimode) are available.
Galvanic RS485 serial communication moduleThe Galvanic RS485 communication module(RS485) is used for DNP3.0 communication. Themodule has one RS485 communication port. TheRS485 is a balanced serial communication thatcan be used either in 2-wire or 4-wireconnections. A 2-wire connection uses the samesignal for RX and TX and is a multidropcommunication with no dedicated Master orslave. This variant requires however a control ofthe output. The 4-wire connection has separatedsignals for RX and TX multidrop communicationwith a dedicated Master and the rest are slaves.No special control signal is needed in this case.
GPS time synchronization module GTMThis module includes a GPS receiver used fortime synchronization. The GPS has one SMAcontact for connection to an antenna. It alsoincludes an optical PPS ST-connector output.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
28 ABB
IRIG-B Time synchronizing moduleThe IRIG-B time synchronizing module is used foraccurate time synchronizing of the IED from astation clock.
Electrical (BNC) and optical connection (ST) for0XX and 12X IRIG-B support.
Transformer input module TRMThe transformer input module is used togalvanically separate and transform the secondary
currents and voltages generated by themeasuring transformers. The module has twelveinputs in different combinations of currents andvoltage inputs.
Alternative connectors of Ring lug orCompression type can be ordered.
Layout and dimensionsDimensions
xx05000059.vsd
EA
BC
F
D
IEC05000059 V1 EN
Figure 14. 1/1 x 19” case with rear cover
Case size A B C D E F
6U, 1/1 x 19” 265.9 448.1 201.1 242.1 252.9 430.3
(mm)
Mounting alternativesThe following mounting alternatives are available(IP40 protection from the front):
• 19” rack mounting kit• Flush mounting kit with cut-out dimensions:
– 1/2 case size (h) 254.3 mm (w) 210.1 mm– 1/1 case size (h) 254.3 mm (w) 434.7 mm
• Wall mounting kit
See ordering for details about available mountingalternatives.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 29
19. Connection diagrams
Table 2. Designations for 1/1 x 19” casing with 2 TRM slots
1MRK002801-AC-6-670-1.2-PG V1 EN
Module Rear Positions
PSM X11
BIM, BOM, SOM,IOM or MIM
X31 and X32 etc. to X131and X132
SLM X301:A, B, C, D
LDCM, IRIG-B orRS485
X302
LDCM or RS485 X303
OEM X311:A, B, C, D
LDCM, RS485 orGTM
X312, X313, X322, X323
TRM 1 X401
TRM 2 X411
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
30 ABB
1MRK002801-AC-10-670-1.2-PG V1 EN
Figure 15. Transformer input module (TRM)
■ Indicates high polarity
CT/VT-input designation according to figure 15
Cur
rent
/vol
tage
conf
igur
atio
n(5
0/60
Hz)
AI01 AI02 AI03 AI04 AI05 AI06 AI07 AI08 AI09 AI10 AI11 AI12
12I, 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A12I, 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A9I+3U,1A
1A 1A 1A 1A 1A 1A 1A 1A 1A 110-220V 110-220V 110-220V
9I+3U,5A
5A 5A 5A 5A 5A 5A 5A 5A 5A 110-220V 110-220V 110-220V
6I+6U,1A
1A 1A 1A 1A 1A 1A 110-220V 110-220V 110-220V 110-220V 110-220V 110-220V
6I+6U,5A
5A 5A 5A 5A 5A 5A 110-220V 110-220V 110-220V 110-220V 110-220V 110-220V
Note that internal polarity can be adjusted by setting of analog input CT neutral direction and/or on SMAI pre-processing function blocks.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 31
1MRK002801-AC-11-670-1.2-PG V1 EN
Figure 16. Binary input module (BIM). Input contactsnamed XA corresponds to rear positionX31, X41, and so on, and input contactsnamed XB to rear position X32, X42, andso on.
1MRK002801-AC-15-670-1.2-PG V1 EN
Figure 17. mA input module (MIM)
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
32 ABB
1MRK002801-AC-8-670-1.2-PG V1 EN
Figure 18. IED with basic functionality and communication interfaces
1MRK002801-AC-7-670-1.2-PG V1 EN
Figure 19. Power supply module (PSM)
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 33
1MRK002801-AC-12-670-1.2-PG V1 EN
Figure 20. Binary output module (BOM). Output contacts named XA corresponds to rear position X31, X41, andso on, and output contacts named XB to rear position X32, X42, and so on.
1MRK002801-AC-13-670-1.2-PG V1 EN
Figure 21. Static output module (SOM)
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
34 ABB
1MRK002801-AC-14-670-1.2-PG V1 EN
Figure 22. Binary in/out module (IOM). Input contacts named XA corresponds to rear position X31, X41, and soon, and output contacts named XB to rear position X32, X42, and so on.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 35
20. Technical data
General
Definitions
Reference value The specified value of an influencing factor to which are referred the characteristics of the equipment
Nominal range The range of values of an influencing quantity (factor) within which, under specified conditions,the equipment meets the specified requirements
Operative range The range of values of a given energizing quantity for which the equipment, under specifiedconditions, is able to perform its intended functions according to the specified requirements
Energizing quantities, rated values and limitsAnalog inputs
Table 3. TRM - Energizing quantities, rated values and limits for protection transformer modules
Quantity Rated value Nominal range
Current Ir = 1 or 5 A (0.2-40) × Ir
Operative range (0-100) x Ir
Permissive overload 4 × Ir cont.100 × Ir for 1 s *)
Burden < 150 mVA at Ir = 5 A< 20 mVA at Ir = 1 A
Ac voltage Ur = 110 V 0.5–288 V
Operative range (0–340) V
Permissive overload 420 V cont.450 V 10 s
Burden < 20 mVA at 110 V
Frequency fr = 50/60 Hz ± 5%
*) max. 350 A for 1 s when COMBITEST test switch is included.
Table 4. MIM - mA input module
Quantity: Rated value: Nominal range:
Input resistance Rin = 194 Ohm -
Input range ± 5, ± 10, ± 20mA0-5, 0-10, 0-20, 4-20mA
-
Power consumptioneach mA-boardeach mA input
£ 2 W£ 0.1 W
-
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
36 ABB
Table 5. OEM - Optical ethernet module
Quantity Rated value
Number of channels 1 or 2
Standard IEEE 802.3u 100BASE-FX
Type of fiber 62.5/125 mm multimode fibre
Wave length 1300 nm
Optical connector Type ST
Communication speed Fast Ethernet 100 MB
Auxiliary DC voltage
Table 6. PSM - Power supply module
Quantity Rated value Nominal range
Auxiliary dc voltage, EL (input) EL = (24 - 60) VEL = (90 - 250) V
EL ± 20%EL ± 20%
Power consumption 50 W typically -
Auxiliary DC power in-rush < 5 A during 0.1 s -
Binary inputs and outputs
Table 7. BIM - Binary input module
Quantity Rated value Nominal range
Binary inputs 16 -
DC voltage, RL 24/30 V48/60 V110/125 V220/250 V
RL ± 20%RL ± 20%RL ± 20%RL ± 20%
Power consumption24/30 V48/60 V110/125 V220/250 V
max. 0.05 W/inputmax. 0.1 W/inputmax. 0.2 W/inputmax. 0.4 W/input
-
Counter input frequency 10 pulses/s max -
Oscillating signal discriminator Blocking settable 1–40 HzRelease settable 1–30 Hz
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 37
Table 8. BIM - Binary input module with enhanced pulse counting capabilities
Quantity Rated value Nominal range
Binary inputs 16 -
DC voltage, RL 24/30 V48/60 V110/125 V220/250 V
RL ± 20%RL ± 20%RL ± 20%RL ± 20%
Power consumption24/30 V48/60 V110/125 V220/250 V
max. 0.05 W/inputmax. 0.1 W/inputmax. 0.2 W/inputmax. 0.4 W/input
-
Counter input frequency 10 pulses/s max -
Balanced counter input frequency 40 pulses/s max -
Oscillating signal discriminator Blocking settable 1–40 HzRelease settable 1–30 Hz
Table 9. IOM - Binary input/output module
Quantity Rated value Nominal range
Binary inputs 8 -
DC voltage, RL 24/30 V48/60 V110/125 V220/250 V
RL ± 20%RL ± 20%RL ± 20%RL ± 20%
Power consumption24/30 V48/60 V110/125 V220/250 V
max. 0.05 W/inputmax. 0.1 W/inputmax. 0.2 W/inputmax. 0.4 W/input
-
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
38 ABB
Table 10. IOM - Binary input/output module contact data (reference standard: IEC 61810-2)
Function or quantity Trip and signal relays Fast signal relays (parallelreed relay)
Binary outputs 10 2
Max system voltage 250 V AC, DC 250 V DC
Test voltage across open contact, 1 min 1000 V rms 800 V DC
Current carrying capacityPer relay, continuousPer relay, 1 sPer process connector pin, continuous
8 A10 A12 A
8 A10 A12 A
Making capacity at inductive load with L/R>10 ms 0.2 s1.0 s
30 A10 A
0.4 A0.4 A
Making capacity at resistive load 0.2 s1.0 s
30 A10 A
220–250 V/0,4 A110–125 V/0,4 A48–60 V/0.2 A24–30 V/0.1 A
Breaking capacity for AC, cos φ > 0.4 250 V/8.0 A 250 V/8.0 A
Breaking capacity for DC with L/R < 40 ms 48 V/1 A110 V/0.4 A125 V/0.35 A220 V/0.2 A250 V/0.15 A
48 V/1 A110 V/0.4 A125 V/0.35 A220 V/0.2 A250 V/0.15 A
Maximum capacitive load - 10 nF
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 39
Table 11. IOM with MOV - contact data (reference standard: IEC 60255-23)
Function or quantity Trip and Signal relays Fast signal relays (parallel reed relay)
Binary outputs IOM: 10 IOM: 2
Max system voltage 250 V AC, DC 250 V DC
Test voltage across opencontact, 1 min
250 V rms 250 V rms
Current carrying capacityPer relay, continuousPer relay, 1 sPer process connector pin,continuous
8 A10 A12 A
8 A10 A12 A
Making capacity at inductiveloadwith L/R>10 ms0.2 s1.0 s
30 A10 A
0.4 A0.4 A
Making capacity at resistive load 0.2 s1.0 s
30 A10 A
220–250 V/0,4 A110–125 V/0,4 A48–60 V/0.2 A24–30 V/0.1 A
Breaking capacity for AC, cosj>0.4
250 V/8.0 A 250 V/8.0 A
Breaking capacity for DC with L/R < 40 ms
48 V/1 A110 V/0.4 A220 V/0.2 A250 V/0.15 A
48 V/1 A110 V/0.4 A220 V/0.2 A250 V/0.15 A
Maximum capacitive load - 10 nF
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
40 ABB
Table 12. SOM - Static Output Module (reference standard: IEC 61810-2): Static binary outputs
Function of quantity Static binary output trip
Rated voltage 48 - 60 VDC 110 - 250 VDC
Number of outputs 6 6
Impedance open state ~300 kΩ ~810 kΩ
Test voltage across open contact, 1 min No galvanic separation No galvanic separation
Current carrying capacity:
Continuous 5A 5A
1.0s 10A 10A
Making capacity at capacitive load withthe maximum capacitance of 0.2 μF :
0.2s 30A 30A
1.0s 10A 10A
Breaking capacity for DC with L/R ≤ 40ms 48V / 1A 110V / 0.4A
60V / 0,75A 125V / 0.35A
220V / 0.2A
250V / 0.15A
Operating time <1ms <1ms
Table 13. SOM - Static Output module data (reference standard: IEC 61810-2): Electromechanical relay outputs
Function of quantity Trip and signal relays
Max system voltage 250V AC/DC
Number of outputs 6
Test voltage across open contact, 1 min 1000V rms
Current carrying capacity:
Continuous 8A
1.0s 10A
Making capacity at capacitive load with the maximumcapacitance of 0.2 μF:
0.2s 30A
1.0s 10A
Breaking capacity for DC with L/R ≤ 40ms 48V / 1A
110V / 0.4A
125V / 0,35A
220V / 0,2A
250V / 0.15A
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 41
Table 14. BOM - Binary output module contact data (reference standard: IEC 61810-2)
Function or quantity Trip and Signal relays
Binary outputs 24
Max system voltage 250 V AC, DC
Test voltage across open contact, 1 min 1000 V rms
Current carrying capacityPer relay, continuousPer relay, 1 sPer process connector pin, continuous
8 A10 A12 A
Making capacity at inductive load with L/R>10 ms0.2 s1.0 s
30 A10 A
Breaking capacity for AC, cos j>0.4 250 V/8.0 A
Breaking capacity for DC with L/R < 40 ms 48 V/1 A110 V/0.4 A125 V/0.35 A220 V/0.2 A250 V/0.15 A
Influencing factors
Table 15. Temperature and humidity influence
Parameter Reference value Nominal range Influence
Ambient temperature,operate value
+20 °C -10 °C to +55 °C 0.02% /°C
Relative humidityOperative range
10%-90%0%-95%
10%-90% -
Storage temperature -40 °C to +70 °C - -
Table 16. Auxiliary DC supply voltage influence on functionality during operation
Dependence on Reference value Within nominalrange
Influence
Ripple, in DC auxiliary voltageOperative range
max. 2%Full wave rectified
15% of EL 0.01% /%
Auxiliary voltage dependence, operatevalue
± 20% of EL 0.01% /%
Interrupted auxiliary DC voltage
24-60 V DC ± 20% 90-250 V DC ± 20%
Interruption interval0–50 ms
No restart
0–∞ s Correct behaviour at powerdown
Restart time <300 s
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
42 ABB
Table 17. Frequency influence (reference standard: IEC 60255–1)
Dependence on Within nominal range Influence
Frequency dependence, operate value fr ± 2.5 Hz for 50 Hzfr ± 3.0 Hz for 60 Hz
± 1.0% / Hz
Frequency dependence for differentialprotection
fr ± 2.5 Hz for 50 Hzfr ± 3.0 Hz for 50 Hz
± 2.0% / Hz
Harmonic frequency dependence (20%content)
2nd, 3rd and 5th harmonic of fr ± 1.0%
Harmonic frequency dependence fordifferential protection (10% content)
2nd, 3rd and 5th harmonic of fr ± 6.0%
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 43
Type tests according to standards
Table 18. Electromagnetic compatibility
Test Type test values Reference standards
1 MHz burst disturbance 2.5 kV IEC 60255-22-1
100 kHz slow damped oscillatory waveimmunity test
2.5 kV IEC 61000-4-18, Class III
Ring wave immunity test, 100 kHz 2-4 kV IEC 61000-4-12, Class IV
Surge withstand capability test 2.5 kV, oscillatory4.0 kV, fast transient
IEEE/ANSI C37.90.1
Electrostatic dischargeDirect applicationIndirect application
15 kV air discharge8 kV contact discharge8 kV contact discharge
IEC 60255-22-2, Class IV IEC 61000-4-2, Class IV
Electrostatic dischargeDirect applicationIndirect application
15 kV air discharge8 kV contact discharge8 kV contact discharge
IEEE/ANSI C37.90.1
Fast transient disturbance 4 kV IEC 60255-22-4, Class A
Surge immunity test 1-2 kV, 1.2/50 mshigh energy
IEC 60255-22-5
Power frequency immunity test 150-300 V, 50 Hz IEC 60255-22-7, Class A
Conducted common mode immunity test 15 Hz-150 kHz IEC 61000-4-16, Class IV
Power frequency magnetic field test 1000 A/m, 3 s100 A/m, cont.
IEC 61000-4-8, Class V
Damped oscillatory magnetic field test 100 A/m IEC 61000-4-10, Class V
Radiated electromagnetic field disturbance 20 V/m, 80-1000 MHz 1.4-2.7 GHz
IEC 60255-22-3
Radiated electromagnetic field disturbance 35 V/m26-1000 MHz
IEEE/ANSI C37.90.2
Conducted electromagnetic field disturbance 10 V, 0.15-80 MHz IEC 60255-22-6
Radiated emission 30-1000 MHz IEC 60255-25
Conducted emission 0.15-30 MHz IEC 60255-25
Table 19. Insulation
Test Type test values Reference standard
Dielectric test 2.0 kV AC, 1 min. IEC 60255-5
Impulse voltage test 5 kV, 1.2/50 ms, 0.5 J
Insulation resistance >100 MW at 500 VDC
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
44 ABB
Table 20. Environmental tests
Test Type test value Reference standard
Cold test Test Ad for 16 h at -25°C IEC 60068-2-1
Storage test Test Ad for 16 h at -40°C IEC 60068-2-1
Dry heat test Test Bd for 16 h at +70°C IEC 60068-2-2
Damp heat test, steady state Test Ca for 4 days at +40 °C and humidity 93% IEC 60068-2-78
Damp heat test, cyclic Test Db for 6 cycles at +25 to +55 °C andhumidity 93 to 95% (1 cycle = 24 hours)
IEC 60068-2-30
Table 21. CE compliance
Test According to
Immunity EN 50263
Emissivity EN 50263
Low voltage directive EN 50178
Table 22. Mechanical tests
Test Type test values Reference standards
Vibration response test Class II IEC 60255-21-1
Vibration endurance test Class I IEC 60255-21-1
Shock response test Class II IEC 60255-21-2
Shock withstand test Class I IEC 60255-21-2
Bump test Class I IEC 60255-21-2
Seismic test Class II IEC 60255-21-3
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 45
Differential protection
Table 23. Busbar differential protection
Function Range or value Accuracy
Operating characteristic S=0.53 fixed ± 2.0% of Ir for I < Ir± 2.0% of I for I > Ir
Reset ratio > 95% -
Differential current operating level (1-100000) A ± 2.0% of Ir for I < Ir± 2.0% of I for I > Ir
Sensitive differential operationlevel
(1-100000) A ± 2.0% of Ir for I < Ir± 2.0% of I for I < Ir
Check zone operation level (0-100000) A ± 2.0% of Ir for I < Ir± 2.0% of I for I > Ir
Check zone slope (0.0-0.9) -
Timers (0.000-60.000) s ± 0.5% ± 10 ms
Timers (0.00-6000.00) s ± 0.5% ± 10 ms
Operate time 19 ms typically at 0 to 2 x Id12 ms typically at 0 to 10 x Id
-
Reset time 21 ms typically at 2 to 0 x Id29 ms typically at 10 to 0 x Id
-
Critical impulse time 8 ms typically at 0 to 2 x Id -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
46 ABB
Current protection
Table 24. Four step phase overcurrent protection OC4PTOC
Function Setting range Accuracy
Operate current (1-2500)% of lBase ± 1.0% of Ir at I ≤ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Min. operating current (1-100)% of lBase ± 1.0% of Ir at I ≤ Ir±1.0% of I at I > Ir
Maximum forward angle (40.0–70.0) degrees ± 2.0 degrees
Minimum forward angle (75.0–90.0) degrees ± 2.0 degrees
2nd harmonic blocking (5–100)% of fundamental ± 2.0% of Ir
Independent time delay (0.000-60.000) s ± 0.5% ±10 ms
Minimum operate time (0.000-60.000) s ± 0.5% ±10 ms
Inverse characteristics, seetable 79, table 80 and table 81
19 curve types See table 79, table 80 and table81
Operate time, start function 25 ms typically at 0 to 2 x Iset -
Reset time, start function 25 ms typically at 2 to 0 x Iset -
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Impulse margin time 15 ms typically -
Table 25. Four step single phase overcurrent protection PH4SPTOC
Function Setting range Accuracy
Operate current (1-2500)% of lbase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Second harmonic blocking (5–100)% of fundamental ± 2.0% of Ir
Independent time delay (0.000-60.000) s ± 0.5% ± 10 ms
Minimum operate time (0.000-60.000) s ± 0.5% ± 10 ms
Inverse characteristics, seetable 79 and table 80
19 curve types See table 79 and table 80
Operate time, start function 25 ms typically at 0 to 2 x Iset -
Reset time, start function 25 ms typically at 2 to 0 x Iset -
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Impulse margin time 15 ms typically -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 47
Table 26. Thermal overload protection, two time constants TRPTTR
Function Range or value Accuracy
Base current 1 and 2 (30–250)% of IBase ± 1.0% of Ir
Operate time:
2 2
2 2ln p
b
I It
I It
æ ö-ç ÷= ×ç ÷-è ø
EQUATION1356 V1 EN (Equation 1)
I = Imeasured
Ip = load current before overloadoccursTime constant τ = (1–500)minutes
IEC 60255–8, ±5% + 200 ms
Alarm level 1 and 2 (50–99)% of heat content tripvalue
± 2.0% of heat content trip
Operate current (50–250)% of IBase ± 1.0% of Ir
Reset level temperature (10–95)% of heat content trip ± 2.0% of heat content trip
Table 27. Breaker failure protection CCRBRF
Function Range or value Accuracy
Operate phase current (5-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio, phase current > 95% -
Operate residual current (2-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio, residual current > 95% -
Phase current level for blocking ofcontact function
(5-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Timers (0.000-60.000) s ± 0.5% ±10 ms
Operate time for current detection 10 ms typically -
Reset time for current detection 15 ms maximum -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
48 ABB
Table 28. Breaker failure protection, single phase version CCSRBRF
Function Range or value Accuracy
Operate phase current (5-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio, phase current > 95% -
Phase current level for blocking ofcontact function
(5-200)% of lBase ± 1.0% of Ir at I £ Ir± 1.0% of I at I > Ir
Reset ratio > 95% -
Timers (0.000-60.000) s ± 0.5% ± 10 ms
Operate time for current detection 10 ms typically -
Reset time for current detection 15 ms maximum -
Table 29. Directional underpower protection GUPPDUP
Function Range or value Accuracy
Power level (0.0–500.0)% of SBase At low setting:(0.5-2.0)% of SBase(2.0-10)% of SBase
± 1.0% of Sr at S < Sr
± 1.0% of S at S > Sr
< ± 50% of set value< ± 20% of set value
Characteristic angle (-180.0–180.0) degrees 2 degrees
Timers (0.00-6000.00) s ± 0.5% ± 10 ms
Table 30. Directional overpower protection GOPPDOP
Function Range or value Accuracy
Power level (0.0–500.0)% of Sbase
At low setting:(0.5-2.0)% of Sbase
(2.0-10)% of Sbase
± 1.0% of Sr at S < Sr
± 1.0% of S at S > Sr
< ± 50% of set value< ± 20% of set value
Characteristic angle (-180.0–180.0) degrees 2 degrees
Timers (0.00-6000.00) s ± 0.5% ± 10 ms
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 49
Table 31. Capacitor bank protection CBPGAPC
Function Range or value Accuracy
Operate value, overcurrent (0-900)% of lBase ± 1.0% of Ir at I < Ir± 1.0% of I at I > Ir
Reset ratio, overcurrent >95% -
Operate time, start 10 ms typically -
Reset time, start 30 ms typically -
Critical impulse time, overcurrent protectionstart
2 ms typically at 0.5 to.2xIset1 ms typically at 0.5 to 10xIset
-
Impulse margin time, overcurrent protectionstart
15 ms typically
Operate value, undercurrent (5-100)% of IBase ± 1.0% of Ir at I < Ir± 1.0% of I at I > Ir
Reset ratio, undercurrent <105% -
Operate value, reconnection inhibit function (4-1000)% of IBase ± 1.0% of Ir at I < Ir± 1.0% of I at I > Ir
Operate value, reactive power overloadfunction
(5-900)% ± 1.0% of Sr at S < Sr
± 1.0% of S at S > Sr
Operate value, voltage protection functionfor harmonic overload (Definite time)
(5-500)% ± 0.5% of Ur at U<Ur
± 0.5% of U at U>Ur
Operate value, voltage protection functionfor harmonic overload (Inverse time)
(80-200)% ± 0.5% of Ur at U<Ur
± 0.5% of U at U>Ur
Inverse time characteristic According to IEC60871-1 (2005) andIEEE/ANSI C37.99 (2000)
10% + 50 ms
Maximum trip delay, harmonic overloadIDMT
(0.05-6000.00) s ± 0.5% ± 10 ms
Minimum trip delay, harmonic overload IDMT (0.05-60.00) s ± 0.5% ± 10 ms
Timers (0.00-6000.00) s ± 0.5% ± 10 ms
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
50 ABB
Voltage protection
Table 32. Two step undervoltage protection UV2PTUV
Function Range or value Accuracy
Operate voltage, low and high step (1–100)% of UBase ± 0.5% of Ur
Absolute hysteresis (0–100)% of UBase ± 0.5% of Ur
Internal blocking level, step 1 andstep 2
(1–100)% of UBase ± 0.5% of Ur
Inverse time characteristics for step 1and step 2, see table 83
- See table 83
Definite time delay, step 1 (0.00 - 6000.00) s ± 0.5% ± 10 ms
Definite time delays (0.000-60.000) s ± 0.5% ±10 ms
Minimum operate time, inversecharacteristics
(0.000–60.000) s ± 0.5% ± 10 ms
Operate time, start function 25 ms typically at 2 x Uset to 0 -
Reset time, start function 25 ms typically at 0 to 2 x Uset -
Critical impulse time 10 ms typically at 2 x Uset to 0 -
Impulse margin time 15 ms typically -
Table 33. Two step overvoltage protection OV2PTOV
Function Range or value Accuracy
Operate voltage, step 1 and 2 (1-200)% of UBase ± 0.5% of Ur at U < Ur
± 0.5% of U at U > Ur
Absolute hysteresis (0–100)% of UBase ± 0.5% of Ur at U < Ur
± 0.5% of U at U > Ur
Inverse time characteristics for steps1 and 2, see table 82
- See table 82
Definite time delay, step 1 (0.00 - 6000.00) s ± 0.5% ± 10 ms
Definite time delays (0.000-60.000) s ± 0.5% ± 10 ms
Minimum operate time, Inversecharacteristics
(0.000-60.000) s ± 0.5% ± 10 ms
Operate time, start function 25 ms typically at 0 to 2 x Uset -
Reset time, start function 25 ms typically at 2 to 0 x Uset -
Critical impulse time 10 ms typically at 0 to 2 x Uset -
Impulse margin time 15 ms typically -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 51
Table 34. Two step residual overvoltage protection ROV2PTOV
Function Range or value Accuracy
Operate voltage, step 1 and step 2 (1-200)% of UBase ± 0.5% of Ur at U < Ur
± 1.0% of U at U > Ur
Absolute hysteresis (0–100)% of UBase ± 0.5% of Ur at U < Ur
± 1.0% of U at U > Ur
Inverse time characteristics for lowand high step, see table 84
- See table 84
Definite time setting, step 1 (0.00–6000.00) s ± 0.5% ± 10 ms
Definite time setting (0.000–60.000) s ± 0.5% ± 10 ms
Minimum operate time (0.000-60.000) s ± 0.5% ± 10 ms
Operate time, start function 25 ms typically at 0 to 2 x Uset -
Reset time, start function 25 ms typically at 2 to 0 x Uset -
Critical impulse time 10 ms typically at 0 to 2 x Uset -
Impulse margin time 15 ms typically -
Table 35. Voltage differential protection VDCPTOV
Function Range or value Accuracy
Voltage difference for alarm andtrip
(0.0–100.0) % of UBase ± 0.5 % of Ur
Under voltage level (0.0–100.0) % of UBase ± 0.5% of Ur
Timers (0.000–60.000)s ± 0.5% ± 10 ms
Table 36. Loss of voltage check LOVPTUV
Function Range or value Accuracy
Operate voltage (0–100)% of UBase ± 0.5% of Ur
Pulse timer (0.050–60.000) s ± 0.5% ± 10 ms
Timers (0.000–60.000) s ± 0.5% ± 10 ms
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
52 ABB
Frequency protection
Table 37. Underfrequency protection SAPTUF
Function Range or value Accuracy
Operate value, start function (35.00-75.00) Hz ± 2.0 mHz
Operate time, start function 100 ms typically -
Reset time, start function 100 ms typically -
Operate time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Reset time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Voltage dependent time delay
( )ExponentU UMin
t tMax tMin tMinUNom UMin
-= × - +
-é ùê úë û
EQUATION1182 V1 EN (Equation 2)
U=Umeasured
Settings:UNom=(50-150)% of Ubase
UMin=(50-150)% of Ubase
Exponent=0.0-5.0tMax=(0.000-60.000)stMin=(0.000-60.000)s
5% + 200 ms
Table 38. Overfrequency protection SAPTOF
Function Range or value Accuracy
Operate value, start function (35.00-75.00) Hz ± 2.0 mHz atsymmetrical three-phase voltage
Operate time, start function 100 ms typically at fset -0.5 Hz to fset +0.5 Hz -
Reset time, start function 100 ms typically -
Operate time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Reset time, definite time function (0.000-60.000)s ± 0.5% ± 10 ms
Table 39. Rate-of-change frequency protection SAPFRC
Function Range or value Accuracy
Operate value, start function (-10.00-10.00) Hz/s ± 10.0 mHz/s
Operate value, internal blocking level (0-100)% of UBase ± 0.5% of Ur
Operate time, start function 100 ms typically -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 53
Multipurpose protection
Table 40. General current and voltage protection CVGAPC
Function Range or value Accuracy
Measuring current input phase1, phase2, phase3, PosSeq,NegSeq, 3*ZeroSeq, MaxPh, MinPh,UnbalancePh, phase1-phase2, phase2-phase3, phase3-phase1, MaxPh-Ph,MinPh-Ph, UnbalancePh-Ph
-
Base current (1 - 99999) A -
Measuring voltage input phase1, phase2, phase3, PosSeq, -NegSeq, -3*ZeroSeq, MaxPh, MinPh,UnbalancePh, phase1-phase2, phase2-phase3, phase3-phase1, MaxPh-Ph,MinPh-Ph, UnbalancePh-Ph
-
Base voltage (0.05 - 2000.00) kV -
Start overcurrent, step 1 and 2 (2 - 5000)% of IBase ± 1.0% of Ir for I<Ir± 1.0% of I for I>Ir
Start undercurrent, step 1 and 2 (2 - 150)% of IBase ± 1.0% of Ir for I<Ir± 1.0% of I for I>Ir
Definite time delay (0.00 - 6000.00) s ± 0.5% ± 10 ms
Operate time start overcurrent 25 ms typically at 0 to 2 x Iset -
Reset time start overcurrent 25 ms typically at 2 to 0 x Iset -
Operate time start undercurrent 25 ms typically at 2 to 0 x Iset -
Reset time start undercurrent 25 ms typically at 0 to 2 x Iset -
See table 79 and table 80 Parameter ranges for customer definedcharacteristic no 17:k: 0.05 - 999.00A: 0.0000 - 999.0000B: 0.0000 - 99.0000C: 0.0000 - 1.0000P: 0.0001 - 10.0000PR: 0.005 - 3.000TR: 0.005 - 600.000CR: 0.1 - 10.0
See table 79 and table 80
Voltage level where voltage memorytakes over
(0.0 - 5.0)% of UBase ± 0.5% of Ur
Start overvoltage, step 1 and 2 (2.0 - 200.0)% of UBase ± 0.5% of Ur for U<Ur
± 0.5% of U for U>Ur
Start undervoltage, step 1 and 2 (2.0 - 150.0)% of UBase ± 0.5% of Ur for U<Ur
± 0.5% of U for U>Ur
Operate time, start overvoltage 25 ms typically at 0 to 2 x Uset -
Reset time, start overvoltage 25 ms typically at 2 to 0 x Uset -
Operate time start undervoltage 25 ms typically 2 to 0 x Uset -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
54 ABB
Table 40. General current and voltage protection CVGAPC , continued
Function Range or value Accuracy
Reset time start undervoltage 25 ms typically at 0 to 2 x Uset -
High and low voltage limit, voltagedependent operation
(1.0 - 200.0)% of UBase ± 1.0% of Ur for U<Ur
± 1.0% of U for U>Ur
Directional function Settable: NonDir, forward and reverse -
Relay characteristic angle (-180 to +180) degrees ± 2.0 degrees
Relay operate angle (1 to 90) degrees ± 2.0 degrees
Reset ratio, overcurrent > 95% -
Reset ratio, undercurrent < 105% -
Reset ratio, overvoltage > 95% -
Reset ratio, undervoltage < 105% -
Overcurrent:
Critical impulse time 10 ms typically at 0 to 2 x Iset -
Impulse margin time 15 ms typically -
Undercurrent:
Critical impulse time 10 ms typically at 2 to 0 x Iset -
Impulse margin time 15 ms typically -
Overvoltage:
Critical impulse time 10 ms typically at 0 to 2 x Uset -
Impulse margin time 15 ms typically -
Undervoltage:
Critical impulse time 10 ms typically at 2 to 0 x Uset -
Impulse margin time 15 ms typically -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 55
Secondary system supervision
Table 41. Fuse failure supervision SDDRFUF
Function Range or value Accuracy
Operate voltage, zero sequence (1-100)% of UBase ± 1.0% of Ur
Operate current, zero sequence (1–100)% of IBase ± 1.0% of Ir
Operate voltage, negative sequence (1–100)% of UBase ± 0.5% of Ur
Operate current, negative sequence (1–100)% of IBase ± 1.0% of Ir
Operate voltage change level (1–100)% of UBase ± 5.0% of Ur
Operate current change level (1–100)% of IBase ± 5.0% of Ir
Operate phase voltage (1-100)% of UBase ± 0.5% of Ur
Operate phase current (1-100)% of IBase ± 1.0% of Ir
Operate phase dead line voltage (1-100)% of UBase ± 0.5% of Ur
Operate phase dead line current (1-100)% of IBase ± 1.0% of Ir
Operate time, general start of function 25 ms typically at 1 to 0 of Ubase -
Reset time, general start of function 35 ms typically at 0 to 1 of Ubase -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
56 ABB
Control
Table 42. Autorecloser SMBRREC
Function Range or value Accuracy
Number of autoreclosing shots 1 - 5 -
Autoreclosing open time:shot 1 - t1 1Phshot 1 - t1 2Phshot 1 - t1 3PhHSshot 1 - t1 3PhDld
(0.000-60.000) s
± 0.5% ± 10 ms
shot 2 - t2shot 3 - t3shot 4 - t4shot 5 - t5
(0.00-6000.00) s
Extended autorecloser open time (0.000-60.000) s
Autorecloser maximum wait time for sync (0.00-6000.00) s
Maximum trip pulse duration (0.000-60.000) s
Inhibit reset time (0.000-60.000) s
Reclaim time (0.00-6000.00) s
Minimum time CB must be closed before AR becomes readyfor autoreclosing cycle
(0.00-6000.00) s
Circuit breaker closing pulse length (0.000-60.000) s
CB check time before unsuccessful (0.00-6000.00) s
Wait for master release (0.00-6000.00) s
Wait time after close command before proceeding to next shot (0.000-60.000) s
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 57
Logic
Table 43. Configurable logic blocks
Logic block Quantity with update rate Range or value Accuracy
fast medium normal
LogicAND 90 90 100 - -
LogicOR 90 90 100 - -
LogicXOR 15 15 10 - -
LogicInverter 45 45 50 - -
LogicSRMemory 15 15 10 - -
LogicRSMemory 15 15 10 - -
LogicGate 15 15 10 - -
LogicTimer 15 15 10 (0.000–90000.000) s ± 0.5% ± 10 ms
LogicPulseTimer 15 15 10 (0.000–90000.000) s ± 0.5% ± 10 ms
LogicTimerSet 15 15 10 (0.000–90000.000) s ± 0.5% ± 10 ms
LogicLoopDelay 15 15 10 (0.000–90000.000) s ± 0.5% ± 10 ms
Boolean 16 to Integer 4 4 8 - -
Boolean 16 to integerwith Logic Node
4 4 8 - -
Integer to Boolean 16 4 4 8 - -
Integer to Boolean 16with Logic Node
4 4 8 - -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
58 ABB
Monitoring
Table 44. Measurements CVMMXN
Function Range or value Accuracy
Frequency (0.95-1.05) × fr ± 2.0 mHz
Voltage (0.1-1.5) ×Ur ± 0.5% of Ur at U£Ur
± 0.5% of U at U > Ur
Connected current (0.2-4.0) × Ir ± 0.5% of Ir at I £ Ir± 0.5% of I at I > Ir
Active power, P 0.1 x Ur< U < 1.5 x Ur
0.2 x Ir < I < 4.0 x Ir± 1.0% of Sr at S ≤ Sr
± 1.0% of S at S > Sr
Conditions:0.8 x Ur < U < 1.2 Ur
0.2 x Ir < I < 1.2 Ir
Reactive power, Q 0.1 x Ur< U < 1.5 x Ur
0.2 x Ir < I < 4.0 x Ir
Apparent power, S 0.1 x Ur < U < 1.5 x Ur
0.2 x Ir< I < 4.0 x Ir
Power factor, cos (φ) 0.1 x Ur < U < 1.5 x Ur
0.2 x Ir< I < 4.0 x Ir± 0.02
Table 45. Phase current measurement CMMXU
Function Range or value Accuracy
Current (0.1-4.0) × Ir ± 0.2% of Ir at I ≤ 0.5 × Ir± 0.2% of I at I > 0.5 × Ir
Phase angle (0.1–4.0) x Ir ± 0.5° at 0.2 × Ir < I < 0.5 × Ir± 0.2° at 0.5 × Ir ≤ I < 4.0 × Ir
Table 46. Phase-phase voltage measurement VMMXU
Function Range or value Accuracy
Voltage (10 to 300) V ± 0.3% of U at U ≤ 50 V± 0.2% of U at U > 50 V
Phase angle (10 to 300) V ± 0.3° at U ≤ 50 V± 0.2° at U > 50 V
Table 47. Phase-neutral voltage measurement VNMMXU
Function Range or value Accuracy
Voltage (10 to 300) V ± 0.3% of U at U ≤ 50 V± 0.2% of U at U > 50 V
Phase angle (10 to 300) V ± 0.3° at U ≤ 50 V± 0.2° at U > 50 V
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 59
Table 48. Current sequence component measurement CMSQI
Function Range or value Accuracy
Current positive sequence, I1Three phase settings
(0.1–4.0) × Ir ± 0.2% of Ir at I ≤ 0.5 × Ir± 0.2% of I at I > 0.5 × Ir
Current zero sequence, 3I0Three phase settings
(0.1–1.0) × Ir ± 0.2% of Ir at I ≤ 0.5 × Ir± 0.2% of I at I > 0.5 × Ir
Current negative sequence, I2Three phase settings
(0.1–1.0) × Ir ± 0.2% of Ir at I ≤ 0.5 × Ir± 0.2% of I at I > 0.5 × Ir
Phase angle (0.1–4.0) × Ir ± 0.5° at 0.2 × Ir < I < 0.5 × Ir± 0.2° at 0.5 × Ir ≤ I < 4.0 × Ir
Table 49. Voltage sequence measurement VMSQI
Function Range or value Accuracy
Voltage positive sequence, U1 (10 to 300) V ± 0.3% of U at U ≤ 50 V± 0.2% of U at U > 50 V
Voltage zero sequence, 3U0 (10 to 300) V ± 0.3% of U at U ≤ 50 V± 0.2% of U at U > 50 V
Voltage negative sequence, U2 (10 to 300) V ± 0.3% of U at U ≤ 50 V± 0.2% of U at U > 50 V
Phase angle (10 to 300) V ± 0.3° at U ≤ 50 V± 0.2° at U > 50 V
Table 50. Supervision of mA input signals
Function Range or value Accuracy
mA measuring function ± 5, ± 10, ± 20 mA0-5, 0-10, 0-20, 4-20 mA
± 0.1 % of set value ± 0.005 mA
Max current of transducer toinput
(-20.00 to +20.00) mA
Min current of transducer toinput
(-20.00 to +20.00) mA
Alarm level for input (-20.00 to +20.00) mA
Warning level for input (-20.00 to +20.00) mA
Alarm hysteresis for input (0.0-20.0) mA
Table 51. Event counter CNTGGIO
Function Range or value Accuracy
Counter value 0-10000 -
Max. count up speed 10 pulses/s -
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
60 ABB
Table 52. Disturbance report DRPRDRE
Function Range or value Accuracy
Pre-fault time (0.05–9.90) s -
Post-fault time (0.1–10.0) s -
Limit time (0.5–10.0) s -
Maximum number of recordings 100, first in - first out -
Time tagging resolution 1 ms See table 75
Maximum number of analog inputs 30 + 10 (external + internallyderived)
-
Maximum number of binary inputs 96 -
Maximum number of phasors in the Trip Valuerecorder per recording
30 -
Maximum number of indications in a disturbance report 96 -
Maximum number of events in the Event recording perrecording
150 -
Maximum number of events in the Event list 1000, first in - first out -
Maximum total recording time (3.4 s recording timeand maximum number of channels, typical value)
340 seconds (100 recordings) at50 Hz, 280 seconds (80recordings) at 60 Hz
-
Sampling rate 1 kHz at 50 Hz1.2 kHz at 60 Hz
-
Recording bandwidth (5-300) Hz -
Table 53. Event list
Function Value
Buffer capacity Maximum number of events in the list 1000
Resolution 1 ms
Accuracy Depending on time synchronizing
Table 54. Indications
Function Value
Buffer capacity Maximum number of indications presented for singledisturbance
96
Maximum number of recorded disturbances 100
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 61
Table 55. Event recorder
Function Value
Buffer capacity Maximum number of events in disturbance report 150
Maximum number of disturbance reports 100
Resolution 1 ms
Accuracy Depending on timesynchronizing
Table 56. Trip value recorder
Function Value
Buffer capacity
Maximum number of analog inputs 30
Maximum number of disturbance reports 100
Table 57. Disturbance recorder
Function Value
Buffer capacity Maximum number of analog inputs 40
Maximum number of binary inputs 96
Maximum number of disturbance reports 100
Maximum total recording time (3.4 s recording time and maximum numberof channels, typical value)
340 seconds (100 recordings) at 50 Hz280 seconds (80 recordings) at 60 Hz
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
62 ABB
Metering
Table 58. Pulse counter PCGGIO
Function Setting range Accuracy
Input frequency See Binary Input Module (BIM) -
Cycle time for report of countervalue
(1–3600) s -
Table 59. Energy metering ETPMMTR
Function Range or value Accuracy
Energy metering kWh Export/Import, kvarh Export/Import
Input from MMXU. No extra error at steady load
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 63
Station communication
Table 60. IEC 61850-8-1 communication protocol
Function Value
Protocol IEC 61850-8-1
Communication speed for the IEDs 100BASE-FX
Protocol IEC 608–5–103
Communication speed for the IEDs 9600 or 19200 Bd
Protocol DNP3.0
Communication speed for the IEDs 300–19200 Bd
Protocol TCP/IP, Ethernet
Communication speed for the IEDs 100 Mbit/s
Table 61. LON communication protocol
Function Value
Protocol LON
Communication speed 1.25 Mbit/s
Table 62. SPA communication protocol
Function Value
Protocol SPA
Communication speed 300, 1200, 2400, 4800, 9600, 19200 or 38400 Bd
Slave number 1 to 899
Table 63. IEC60870-5-103 communication protocol
Function Value
Protocol IEC 60870-5-103
Communication speed 9600, 19200 Bd
Table 64. SLM – LON port
Quantity Range or value
Optical connector Glass fibre: type STPlastic fibre: type HFBR snap-in
Fibre, optical budget Glass fibre: 11 dB (1000 m typically *)Plastic fibre: 7 dB (10 m typically *)
Fibre diameter Glass fibre: 62.5/125 mmPlastic fibre: 1 mm
*) depending on optical budget calculation
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
64 ABB
Table 65. SLM – SPA/IEC 60870-5-103/DNP3 port
Quantity Range or value
Optical connector Glass fibre: type STPlastic fibre: type HFBR snap-in
Fibre, optical budget Glass fibre: 11 dB (3000ft/1000 m typically *)Plastic fibre: 7 dB (80ft/25 m typically *)
Fibre diameter Glass fibre: 62.5/125 mmPlastic fibre: 1 mm
*) depending on optical budget calculation
Table 66. Galvanic RS485 communication module
Quantity Range or value
Communication speed 2400–19200 bauds
External connectors RS-485 6-pole connectorSoft ground 2-pole connector
Table 67. IEC 62439-3 Edition 1 and Edition 2 parallel redundancy protocol
Function Value
Protocol IEC 61850-8-1
Communication speed 100 Base-FX
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 65
Remote communication
Table 68. Line data communication module
Characteristic Range or value
Type of LDCM Short range (SR) Medium range (MR) Long range (LR)
Type of fibre Graded-indexmultimode62.5/125 µm or50/125 µm
Singlemode 9/125 µm Singlemode 9/125 µm
Wave length 850 nm 1310 nm 1550 nm
Optical budgetGraded-index multimode 62.5/125mm, Graded-index multimode 50/125 mm
13 dB (typicaldistance about 3km *)9 dB (typicaldistance about 2km *)
22 dB (typicaldistance 80 km *)
26 dB (typical distance 110 km *)
Optical connector Type ST Type FC/PC Type FC/PC
Protocol C37.94 C37.94implementation **)
C37.94 implementation **)
Data transmission Synchronous Synchronous Synchronous
Transmission rate / Data rate 2 Mb/s / 64 kbit/s 2 Mb/s / 64 kbit/s 2 Mb/s / 64 kbit/s
Clock source Internal or derivedfrom receivedsignal
Internal or derivedfrom received signal
Internal or derived from receivedsignal
*) depending on optical budget calculation**) C37.94 originally defined just for multimode; using same header, configuration and data format as C37.94
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
66 ABB
HardwareIED
Table 69. Case
Material Steel sheet
Front plate Steel sheet profile with cut-out for HMI
Surface treatment Aluzink preplated steel
Finish Light grey (RAL 7035)
Table 70. Water and dust protection level according to IEC 60529
Front IP40 (IP54 with sealing strip)
Rear, sides, top andbottom
IP20
Table 71. Weight
Case size Weight
6U, 1/1 x 19” £ 18 kg
Connection system
Table 72. CT and VT circuit connectors
Connector type Rated voltage and current Maximum conductor area
Screw compression type 250 V AC, 20 A 4 mm2 (AWG12)2 x 2.5 mm2 (2 x AWG14)
Terminal blocks suitable for ring lug terminals 250 V AC, 20 A 4 mm2 (AWG12)
Table 73. Binary I/O connection system
Connector type Rated voltage Maximum conductor area
Screw compression type 250 V AC 2.5 mm2 (AWG14)2 × 1 mm2 (2 x AWG18)
Terminal blocks suitable for ring lug terminals 300 V AC 3 mm2 (AWG14)
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 67
Basic IED functions
Table 74. Self supervision with internal event list
Data Value
Recording manner Continuous, event controlled
List size 1000 events, first in-first out
Table 75. Time synchronization, time tagging
Function Value
Time tagging resolution, events and sampled measurement values 1 ms
Time tagging error with synchronization once/min (minute pulse synchronization),events and sampled measurement values
± 1.0 ms typically
Time tagging error with SNTP synchronization, sampled measurement values ± 1.0 ms typically
Table 76. GPS time synchronization module (GTM)
Function Range or value Accuracy
Receiver – ±1µs relative UTC
Time to reliable time reference with antenna in newposition or after power loss longer than 1 month
<30 minutes –
Time to reliable time reference after a power losslonger than 48 hours
<15 minutes –
Time to reliable time reference after a power lossshorter than 48 hours
<5 minutes –
Table 77. GPS – Antenna and cable
Function Value
Max antenna cable attenuation 26 db @ 1.6 GHz
Antenna cable impedance 50 ohm
Lightning protection Must be provided externally
Antenna cable connector SMA in receiver endTNC in antenna end
Accuracy +/-2μs
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
68 ABB
Table 78. IRIG-B
Quantity Rated value
Number of channels IRIG-B 1
Number of channels PPS 1
Electrical connector:
Electrical connector IRIG-B BNC
Pulse-width modulated 5 Vpp
Amplitude modulated– low level– high level
1-3 Vpp3 x low level, max 9 Vpp
Supported formats IRIG-B 00x, IRIG-B 12x
Accuracy +/-10μs for IRIG-B 00x and +/-100μs for IRIG-B 12x
Input impedance 100 k ohm
Optical connector:
Optical connector PPS and IRIG-B Type ST
Type of fibre 62.5/125 μm multimode fibre
Supported formats IRIG-B 00x, PPS
Accuracy +/- 2μs
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 69
Inverse characteristic
Table 79. ANSI Inverse time characteristics
Function Range or value Accuracy
Operating characteristic:
( )1= + ×
-
æ öç ÷ç ÷è ø
P
At B k
I
EQUATION1249-SMALL V1 EN
Reset characteristic:
( )2 1= ×
-
trt kI
EQUATION1250-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01 -
ANSI Extremely Inverse A=28.2, B=0.1217, P=2.0 , tr=29.1 ANSI/IEEE C37.112, 5%+ 40 ms
ANSI Very inverse A=19.61, B=0.491, P=2.0 , tr=21.6
ANSI Normal Inverse A=0.0086, B=0.0185, P=0.02, tr=0.46
ANSI Moderately Inverse A=0.0515, B=0.1140, P=0.02, tr=4.85
ANSI Long Time Extremely Inverse A=64.07, B=0.250, P=2.0, tr=30
ANSI Long Time Very Inverse A=28.55, B=0.712, P=2.0, tr=13.46
ANSI Long Time Inverse A=0.086, B=0.185, P=0.02, tr=4.6
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
70 ABB
Table 80. IEC Inverse time characteristics
Function Range or value Accuracy
Operating characteristic:
( )1= ×
-
æ öç ÷ç ÷è ø
P
At k
I
EQUATION1251-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01 -
Time delay to reset, IEC inverse time (0.000-60.000) s ± 0.5% of set time ± 10 ms
IEC Normal Inverse A=0.14, P=0.02 IEC 60255-151, 5% + 40ms
IEC Very inverse A=13.5, P=1.0
IEC Inverse A=0.14, P=0.02
IEC Extremely inverse A=80.0, P=2.0
IEC Short time inverse A=0.05, P=0.04
IEC Long time inverse A=120, P=1.0
Programmable characteristicOperate characteristic:
( )= + ×
-
æ öç ÷ç ÷è ø
P
At B k
I C
EQUATION1370-SMALL V1 EN
Reset characteristic:
( )= ×
-PR
TRt k
I CR
EQUATION1253-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01A=(0.005-200.000) in steps of 0.001B=(0.00-20.00) in steps of 0.01C=(0.1-10.0) in steps of 0.1P=(0.005-3.000) in steps of 0.001TR=(0.005-100.000) in steps of 0.001CR=(0.1-10.0) in steps of 0.1PR=(0.005-3.000) in steps of 0.001
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 71
Table 81. RI and RD type inverse time characteristics
Function Range or value Accuracy
RI type inverse characteristic
1
0.2360.339
= ×
-
t k
IEQUATION1137-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01 IEC 60255-151, 5% + 40ms
RD type logarithmic inverse characteristic
5.8 1.35= - ×æ öç ÷è ø
tI
Ink
EQUATION1138-SMALL V1 EN
I = Imeasured/Iset
k = (0.05-999) in steps of 0.01
Table 82. Inverse time characteristics for overvoltage protection
Function Range or value Accuracy
Type A curve:
=- >
>
æ öç ÷è ø
tk
U U
U
EQUATION1436-SMALL V1 EN
U> = Uset
U = Umeasured
k = (0.05-1.10) in steps of 0.01 5% +40 ms
Type B curve:
2.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1437-SMALL V1 EN
k = (0.05-1.10) in steps of 0.01
Type C curve:
3.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1438-SMALL V1 EN
k = (0.05-1.10) in steps of 0.01
Programmable curve:
×= +
- >× -
>
æ öç ÷è ø
P
k At D
U UB C
U
EQUATION1439-SMALL V1 EN
k = (0.05-1.10) in steps of 0.01A = (0.005-200.000) in steps of 0.001B = (0.50-100.00) in steps of 0.01C = (0.0-1.0) in steps of 0.1D = (0.000-60.000) in steps of 0.001P = (0.000-3.000) in steps of 0.001
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
72 ABB
Table 83. Inverse time characteristics for undervoltage protection
Function Range or value Accuracy
Type A curve:
=< -
<
æ öç ÷è ø
kt
U U
UEQUATION1431-SMALL V1 EN
U< = Uset
U = UVmeasured
k = (0.05-1.10) in steps of 0.01 5% +40 ms
Type B curve:
2.0
4800.055
32 0.5
×= +
< -× -
<
æ öç ÷è ø
kt
U U
U
EQUATION1432-SMALL V1 EN
U< = Uset
U = Umeasured
k = (0.05-1.10) in steps of 0.01
Programmable curve:
×= +
< -× -
<
é ùê úê úê úæ öê úç ÷ë è ø û
P
k At D
U UB C
U
EQUATION1433-SMALL V1 EN
U< = Uset
U = Umeasured
k = (0.05-1.10) in steps of 0.01A = (0.005-200.000) in steps of 0.001B = (0.50-100.00) in steps of 0.01C = (0.0-1.0) in steps of 0.1D = (0.000-60.000) in steps of 0.001P = (0.000-3.000) in steps of 0.001
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 73
Table 84. Inverse time characteristics for residual overvoltage protection
Function Range or value Accuracy
Type A curve:
=- >
>
æ öç ÷è ø
tk
U U
U
EQUATION1436-SMALL V1 EN
U> = Uset
U = Umeasured
k = (0.05-1.10) in steps of0.01
5% +40 ms
Type B curve:
2.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1437-SMALL V1 EN
k = (0.05-1.10) in steps of0.01
Type C curve:
3.0
480
32 0.5 0.035
=×
- >× - -
>
æ öç ÷è ø
tk
U U
U
EQUATION1438-SMALL V1 EN
k = (0.05-1.10) in steps of0.01
Programmable curve:
×= +
- >× -
>
æ öç ÷è ø
P
k At D
U UB C
U
EQUATION1439-SMALL V1 EN
k = (0.05-1.10) in steps of0.01A = (0.005-200.000) insteps of 0.001B = (0.50-100.00) in stepsof 0.01C = (0.0-1.0) in steps of 0.1D = (0.000-60.000) insteps of 0.001P = (0.000-3.000) in stepsof 0.001
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
74 ABB
21. Ordering
Guidelines
Carefully read and follow the set of rules to ensure problem-free order management. Be aware that certain functionscan only be ordered in combination with other functions and that some functions require specific hardware selections.
Please refer to the available functions table for included application functions.
Product specification
Default:
Option:
Customer specific configuration On request
Connection type for Power supply modules and I/O modules
Rule: Same connection type for Power supply modules and I/O modules must be ordered
Compression terminals 1MRK 002 960-AA
Ring lug terminals 1MRK 002 960-BA
Power supply module
Rule: One Power supply module must be specified
Power supply module (PSM) 24-60 VDC 1MRK 002 239-AB
90-250 VDC 1MRK 002 239-BB
Differential protection
Rule: Only one, Busbar differential protection must be ordered
Busbar differential protection, 2 zones, three phase/up to 8 bays (BUTPTRC,BCZTPDIF, BZNTPDIF, BZITGGIO)
1MRK 002 901-LB
Busbar differential protection, 2 zones, single phase/up to 24 bays (BUSPTRC,BCZSPDIF, BZNSPDIF, BZISGGIO)
1MRK 002 901-NB
Optional functions
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 75
Current protection
Rule: Only one of OC4PTOC and PH4SPTOC can beordered
Four step phase overcurrent protection (OC4PTOC)
Qty:
1 2 3 4
5 6 7 8
1MRK 002 906-BD
Four step single phase overcurrent protection(PH4SPTOC)
Qty:
1 2 3 4 5 6
7 8 9 10 11 12
13
22 23 24
14 15 16 17 18
19 20 21
1MRK 002 907-BB
Thermal overload protection, two time constants(TRPTTR)
Qty:
1 2 1MRK 002 906-NC
Rule: Only one type of Breaker failure protection can beordered
Breaker failure protection (CCRBRF)
Qty
1 2 3 4
5 6 7 8
1MRK 002 906-RC
Breaker failure protection, single phase version(CCSRBRF)
Qty
1 2 3 4 5 6
7 8 9 10 11 12
13
22 23 24
14 15 16 17 18
19 20 21
1MRK 002 907-CB
Directional underpower protection (GUPPDUP)
Qty:
1 2 3 4 1MRK 002 902-FB
Directional overpower protection (GOPPDUP)
Qty:
1 2 3 4 1MRK 002 902-GB
Capacitor bank protection (CBPGAPC)
Qty:
1 2 1MRK 002 902-MA
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
76 ABB
Voltage protection
Two step undervoltage protection (UV2PTUV)
Qty:
1 2 1MRK 002 908-AC
Two step overvoltage protection (OV2PTOV)
Qty:
1 2 1MRK 002 908-DC
Two step residual overvoltage protection (ROV2PTOV)
Qty:
1 2 1MRK 002 908-GC
Voltage differential protection (VDCPTOV)
Qty:
1 2 1MRK 002 924-TB
Loss of voltage check (LOVPTUV)
Qty:
1 2 1MRK 002 902-EB
Frequency protection
Underfrequency protection (SAPTUF)
Qty:
1 2 3 4 5 6 1MRK 002 908-NC
Overfrequency protection (SAPTOF)
Qty:
1 2 3 4 5 6 1MRK 002 908-RC
Rate-of-change frequency protection (SAPFRC)
Qty:
1 2 3 4 5 6 1MRK 002 908-SB
Multipurpose protection
General current and voltage protection (CVGAPC)
Qty:
1 2 3 4 5 6 1MRK 002 902-AB
Secondary system supervision
Fuse failure supervision (SDDRFUF)
Qty:
1 2 1MRK 002 914-GC
Control
Autorecloser (SMBRREC)
Qty:
1 2 1MRK 002 916-TB
Apparatus control for up to 6 bays, max 30 apparatuses(6CBs) incl. interlocking
1MRK 002 916-RD
Station communication
Note: Require 2-channel OEM
IEC 62439-3 Edition 1 parallel redundancy protocol 1MRK 002 924-YR
IEC 62439-3 Edition 2 parallel redundancy protocol 1MRK 002 924-YS
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 77
First local HMI user dialogue language
Rule: One must be ordered
HMI language, English IEC 1MRK 002 930-AA
HMI language, English US 1MRK 002 930-BA
Additional local HMI user dialogue language
Rule: Maximum one alternative
HMI language, German 1MRK 002 920-AB
HMI language, Russian 1MRK 002 920-BB
HMI language, French 1MRK 002 920-DB
HMI language, Spanish 1MRK 002 920-DB
HMI language, Polish 1MRK 002 920-GB
HMI language, Hungarian 1MRK 002 920-FB
HMI language, Czech 1MRK 002 920-HB
HMI language, Swedish 1MRK 002 920-KB
Optional hardwareHuman machine hardware interface
Rule: One must be ordered.
Display type Keypad symbol Case size
Small, alpha numeric IEC 1/1 19" 1MRK 000 008-KB
Medium, graphic display IEC 1/1 19" 1MRK 000 008-MB
Medium, graphic display ANSI 1/1 19" 1MRK 000 008-MC
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
78 ABB
Analog system
Note: The same type of connection terminals has to be ordered for both TRMs
Transformer input module, compression terminals 12I, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CG
Transformer input module, compression terminals 12I, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CH
Transformer input module, compression terminals 9I+3U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-BG
Transformer input module, compression terminals 9I+3U, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-BH
Transformer input module, compression terminals 6I+6U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AG
Transformer input module, compression terminals 6I+6U, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AH
Transformer input module, ring lug terminals 12I, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CC
Transformer input module, ring lug terminals 12I, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-CD
Transformer input module, ring lug terminals 9I+3U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-BC
Transformer input module, ring lug terminals 9I+3U, 5A, 50/60 Hz Qty:
1 2 1MRK 002 247-BD
Transformer input module, ring lug terminals 6I+6U, 1A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AC
Transformer input module, ring lug terminals 6I+6U, 5A, 50/60 Hz
Qty:
1 2 1MRK 002 247-AD
Note: One Analog digital conversion module, with time synchronization is always delivered with each Transformerinput module.
Case size
When ordering I/O modules, observe the maximum quantities according to tables below.
Note: Standard order of location for I/O modules is BIM-BOM-SOM-IOM-MIM from left to right as seen from the rearside of the IED, but can also be freely placed.
Note: Maximum quantity of I/O modules depends on the type of connection terminals.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 79
Maximum quantity of I/O modules
Case sizes BIM IOM BOM/SOM
MIM Maximum in case
1/1 x 19”, two (2) TRM 11 6 4 4 11 (max 4 BOM+SOM+MIM)
1MRK 000 151-ND
Maximum quantity of I/O modules, with ring lug terminals, module limits see above
Case sizes Maximum in case Possible locations for I/O moduleswith ringlugs
1/1 x 19”, two (2) TRM 5 P3, P5, P7, P9, P11 1MRK 000 151-ND
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
80 ABB
Binary input/output modules
Make BIM with 50 mA inrush current the primary choice. BIM with 50 mA inrush current fulfilladditional standards. As a consequence the EMC withstand capability is further increased.BIM with 30 mA inrush current is still available.For pulse counting, for example kWh metering, the BIM with enhanced pulse countingcapabilities must be used.
Binary input module (BIM) 16 inputs
RL 24-30 VDC, 30 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-DB
RL 48-60 VDC, 30 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-AB
RL 110-125 VDC, 30 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-BB
RL 220-250 VDC, 30 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-CB
RL 24-30 VDC, 50 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-DD
RL 48-60 VDC, 50 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-AD
RL 110-125 VDC, 50 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-BD
RL 220-250 VDC, 50 mA Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-CD
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 81
Binary input module (BIM) with enhanced pulsecounting capabilities, 16 inputs
RL 24-30 VDC Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-HA
RL 48-60 VDC Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-EA
RL 110-125 VDC Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-FA
RL 220-250 VDC Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 508-GA
Binary output module 24 output relays (BOM) Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 000 614-AB
Static binary output module (SOM)
RL 48-60 VDC Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 002 614-BA
RL 110-250 VDC Qty: 1 2 3 4 5 6
7 8 9 10 11
1MRK 002 614-CA
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
82 ABB
Make IOM with 50 mA inrush current the primary choice. IOM with 50 mA inrush current fulfilladditional standards. As a consequence the EMC withstand capability is further increased.IOM with 30 mA inrush current is still available.
Binary input/output module (IOM) 8 inputs, 10 outputs, 2 high-speed outputs
RL 24-30 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-GB
RL 48-60 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-AC
RL 110-125 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-BC
RL 220-250 VDC, 30 mA Qty: 1 2 3 4 5 6 1MRK 000 173-CC
RL 24-30 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-GD
RL 48-60 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-AE
RL 110-125 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-BE
RL 220-250 VDC, 50 mA Qty: 1 2 3 4 5 6 1MRK 000 173-CE
Binary input/output module (IOM with MOV), 8 inputs, 10 outputs, 2 high-speed outputs
RL 24-30 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-GC
RL 48-60 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-AD
RL 110-125 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-BD
RL 220-250 VDC Qty: 1 2 3 4 5 6 1MRK 000 173-CD
mA input module 6 channels (MIM) Qty: 1 2 3 4 1MRK 000 284-AB
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 83
Station communication ports
Note: Optical ethernet module, 2 glass interfaces is not allowed together with SLM.
Optical ethernet module, 1 channel glass 1MRK 002 266-AA
Optical ethernet module, 2 channel glass 1MRK 002 266-BA
Serial and LON communication module, supports SPA/IEC 60870-5-103, LON and DNP3.0
Serial/LON plastic interface 1MRK 001 608-AA
Serial plastic/LON glass interface 1MRK 001 608-BA
Serial/LON glass interface 1MRK 001 608-CA
Serial IEC 60870-5-103 plastic interface 1MRK 001 608-DA
Serial IEC 60870-5-103 plastic/glass interface 1MRK 001 608--EA
Serial IEC 60870-5-103 glass interface 1MRK 001 608-FA
Galvanic RS485 communication module for DNP 3.0 1MRK 002 309-AA
Remote end serial communication for C37.94
Optical short range line data communication module(Multi mode 850 nm) (SR LDCM)
Qty:
1 2 1MRK 002 122-AB
Time synchronization
Rule: Only one Time synchronization can be ordered.
GPS Time module (GTM) 1MRK 002 282-AB
IRIG-B Time synchronization module 1MRK 002 305-AA
Engineering facilities
19” rack mounting kit for 1/1 x 19” case Quantity: 1MRK 002 420-CA
Note: Wall mounting not recommended with communication moduleswith fibre connection (SLM, OEM, LDCM)Wall mounting kit for terminal
Quantity: 1MRK 002 420-DA
Flush mounting kit for terminal Quantity: 1MRK 000 020-Y
Flush mounting kit + IP54 sealing (factory mounted). Cannot be orderedseparately thus must be specified when ordering a terminal.
Quantity: 1MRK 002 420-EA
Accessories
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
84 ABB
External current transformer unit
3 pcs SLCE 8–1 summation transformers on apparatus plate (2Uhigh), 1/1 A
Quantity: 1MRK 000 643-EA
3 pcs SLCE 8–1 summation transformers on apparatus plate (2Uhigh), 5/1 A
Quantity: 1MRK 000 643-FA
3 pcs SLCE 8–1 summation transformers on apparatus plate (2Uhigh), 2/1 A
Quantity: 1MRK 000 643-GA
GPS antenna and mounting details
GPS antenna, including mounting kits Quantity: 1MRK 001 640-AA
Cable for antenna, 20 m Quantity: 1MRK 001 665-AA
Cable for antenna, 40 m Quantity: 1MRK 001 665-BA
Interface converter (for remote end data communication)
External interface converter from C37.94 to G703 Quantity: 1 2 1MRK 002 245-AA
External interface converter from C37.94 to G703.E1 Quantity: 1 2 1MRK 002 245-BA
Test switchThe test system COMBITEST intended for usewith the IED 670 products is described in 1MRK512 001-BEN and 1MRK 001024-CA. Pleaserefer to the website:www.abb.com/substationautomation for detailedinformation.
Test switches type RTXP 24 is orderedseparately. Please refer to Section "Related
documents" for reference to correspondingdocuments.
RHGS 6 Case or RHGS 12 Case with mountedRTXP 24 and the on/off switch for dc-supply areordered separately. Please refer to Section"Related documents" for reference tocorresponding documents.
Protection cover
Protective cover for rear side of RHGS6, 6U, 1/4 x 19” Quantity: 1MRK 002 420-AE
Protective cover for rear side of terminal, 6U, 1/1 x 19” Quantity: 1MRK 002 420-AA
Combiflex
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 85
Key switch for settings
Key switch for lock-out of settings via LCD-HMI Quantity: 1MRK 000 611-A
Note: To connect the key switch, leads with 10 A Combiflex socket on one end must be used.
Side-by-side mounting kit Quantity: 1MRK 002 420-Z
Configuration and monitoring tools
Front connection cable between LCD-HMI and PC Quantity: 1MRK 001 665-CA
LED Label special paper A4, 1 pc Quantity: 1MRK 002 038-CA
LED Label special paper Letter, 1 pc Quantity: 1MRK 002 038-DA
Manuals
Note: One (1) IED Connect CD containing user documentation (Operator’s manual, Technical referencemanual, Installation and commissioning manual, Application manual and Getting started guide),Connectivity packages and LED label template is always included for each IED.
Rule: Specify additional quantity of IED Connect CD requested. Quantity: 1MRK 002 290-AB
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
86 ABB
User documentation
Rule: Specify the number of printed manuals requested
Operator’s manual IEC Quantity: 1MRK 505 209-UEN
ANSI Quantity: 1MRK 505 209-UUS
Technical reference manual IEC Quantity: 1MRK 505 208-UEN
ANSI Quantity: 1MRK 505 208-UUS
Installation and commissioning manual IEC Quantity: 1MRK 505 210-UEN
ANSI Quantity: 1MRK 505 210-UUS
Application manual IEC Quantity: 1MRK 505 211-UEN
ANSI Quantity: 1MRK 505 211-UUS
Engineering manual, 670 series Quantity: 1MRK 511 240-UEN
Reference information
For our reference and statistics we would be pleased to be provided with the following application data:
Country: End user:
Station name: Voltage level: kV
Related documentsRelated documents
Documents related to REB670 Identity number
Operator’s manual 1MRK 505 209-UEN
Installation and commissioning manual 1MRK 505 210-UEN
Technical reference manual 1MRK 505 208-UEN
Application manual 1MRK 505 211-UEN
Product guide pre-configured 1MRK 505 212-BEN
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
ABB 87
Connection and Installation components 1MRK 513 003-BEN
Test system, COMBITEST 1MRK 512 001-BEN
Accessories for 670 series IEDs 1MRK 514 012-BEN
670 series SPA and signal list 1MRK 500 092-WEN
IEC 61850 Data objects list for 670 series 1MRK 500 091-WEN
Engineering manual 670 series 1MRK 511 240-UEN
Communication set-up for Relion 670 series 1MRK 505 260-UEN
More information can be found on www.abb.com/substationautomation.
Busbar protection REB670 1MRK 505 273-BEN CCustomized Product version: 1.2
88 ABB
89
Contact us
ABB ABSubstation Automation ProductsSE-721 59 Västerås, SwedenPhone +46 (0) 21 32 50 00Fax +46 (0) 21 14 69 18
www.abb.com/substationautomation
1MR
K 5
05 2
73-B
EN
C©
Cop
yrig
ht 2
012
AB
B. A
ll rig
hts
rese
rved
.