Step 1

Seat Removal: The seat bottom must be removed to install

the covers. Locate one of two clips under the seat bottom

towards the outside of the vehicle. Pull each clip forward to

release the front of the cushion. Push back on the seat while

rotating the front up to release the entire seat bottom.

Step 2

Seat Removal: The hand in the picture is pointing to one of

the two clips that hold the back of the seat down. You will

need to reconnect to these after the cover is installed.

Step 3

Seatbelt Removal: Release the center seatbelt at the

bottom. Push in on the white button and pull the seatbelt

out.

Step 4

Seatbelt Removal: Pull the shoulder belt out of the carrier

on top of the seat.

1741 Back Seat Installation Instructions

Step 5

Passenger Backrest: Pry the top cover off from behind to

expose the screws.

Step 6

Passenger Backrest: Remove the screws and the seatbelt

carrier.

Step 7

Headrest Covers: With the headrest still in the seat, pull

the cover on with the Velcro straps to the front. Massage

the cover from top to bottom and get the cover seams to

line up with the factory seams.

Step 8

Headrest Covers: Remove the headrest from the seatback

by depressing the button on the plastic bezel and lifting up.

Step 9

Headrest Covers: Route the straps under the headrest and

connect to the Velcro sewn inside the back of the cover.

Step 10

Passenger Backrest: Open the armrest, tilt the seat

forward and pull the cover on with the Velcro straps to the

front. Tuck the cover behind the armrest and route the side

Velcro straps around the side of the seat.

Step 11

Passenger Backrest: Tuck the cover behind the armrest.

Fold the armrest into the cavity and then tuck the Velcro

straps under the armrest.

Step 12

Passenger Backrest: Fold the armrest down and find the

straps. Connect to the Velcro sewn inside the cover.

Step 13

Passenger Backrest: Fold the seat forward. The rear cargo

flap needs to be unclipped from the floor and tucked up

inside the back of the seat cover.

Step 14

Passenger Backrest: Find the Velcro on the inside of the

seat and pull around to connect to the Velcro inside the

back of the cover.

Step 15

Passenger Backrest: Tuck the cover under all of the

plastic headrest bezels, pull tabs and child restraints. (Cut

SMALL relief slits in the corners of the holes if needed).

Reinstall the seatbelt carrier.

Step 16

Passenger Backrest: Massage the cover ceiling to floor

and tuck the Velcro straps under the backrest.

Photo Unavailable

Step 17

Passenger Backrest: Fold the seat down and locate the

Velcro straps. Pull tightly and connect to the Velcro sewn

inside the back of the cover. Massage cover from ceiling to

floor and refasten Velcro to eliminate wrinkles.

Step 18

Driver Backrest: Tilt the seat forward and pull the cover

on with the Velcro straps to the front. Follow Step 13- Step

17 to complete the installation.

Step 19

Armrest Cover: Open the armrest and pull the cover on

with the Velcro straps to the front.

Step 20

Armrest Cover: Massage the cover top to bottom and tuck

the straps under the armrest.

Step 21

Armrest Cover: Fold the armrest down and pull the straps

through. Connect to the Velcro sewn inside of the cover.

Step 22

Armrest Cover: Tuck the cover under the plastic cup

holder.

Step 23

Seat Bottom: Pull the straps apart and pull the cover onto

the seat with the Velcro straps to the front. Connect one far

left and one far right to help hold the cover in place.

Step 24

Seat Bottom: Flip the seat upside down and route all the

straps to the Velcro on the tail of the cover. Make sure to

keep the cover aligned with the seat.

Step 25

Seat Bottom: Flip the seat over and find the straps located

at the seatbelt slots. Gather them and stuff them through the

seatbelt slots

Step 26

Seat Bottom: Flip the seat over and find the 1" seatbelt

slot straps. Pull them tightly and connect to the 2" Velcro

straps. Flip the seat over and massage the cover and

refasten Velcro to eliminate wrinkles. The seat bottom

cushion is flexible so the cover will seem a little loose until

reinstalled into the car.

Step 27

Seat Bottom: Reinstall the seat bottom. Feed the seatbelts

into the slots. With the front of the seat up, push the seat

back into position. You will need to get both outside

corners to connect back onto the hooks.

Step 28

Seat Bottom: Once the seat bottom is hooked in the rear

corners, push down on the front outside portions to click it

into place.