1730 MCS Technical Specifications
Transcript of 1730 MCS Technical Specifications
IOWA MOLD TOOLING CO., INC.
P.O. Box 189Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com
1730 MCS Technical
Specifications
Manual # 99906495
Revised 02-06-2020
Copyright © 2020 Iowa Mold Tooling Co., Inc.All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company
ii
1730 MCS - Manual # 99906495
Operating, servicing and maintaining this vehicle or equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle or equipment in a well-ventilated area and wear gloves or wash your hands frequently when servicing. For more information go to www.P65Warnings.ca.gov. 70490167
70490167PROP 65BKS 5-29-18
ORANGE , BLACK AND WHITE3.27” 2.70”
CN
iii
1730 MCS - Manual # 99906495
Table of Contents
Section - 1 1
1730 MCS - Specifications .............................................................................................................................21730 MCS - Specifications - Continued .........................................................................................................31730 MCS - Specifications - Metric ................................................................................................................51730 MCS - Metric Specifications - Continued ..............................................................................................61730 MCS- Metric Specifications - Continued ..............................................................................................7
Section - 2 9
1730 MCS - Lifting Capacity Chart, K1 ........................................................................................................101730 MCS - Lifting Capacity Chart, K2 ........................................................................................................ 111730 MCS - Lifting Capacity Chart, K3 ........................................................................................................121730 MCS - Lifting Capacity Chart, K4 ........................................................................................................131730 MCS - Lifting Capacity Chart, K5 ........................................................................................................141730 MCS - Lifting Capacity Chart, K6 ........................................................................................................151730 MCS - Lifting Capacity Chart, K8 ........................................................................................................161730 MCS - Lifting Capacity with Winch ......................................................................................................17
Section - 3 19
1730 MCS - Pressure setting diagram, fixed flow pump & Danfoss RC ......................................................201730 MCS - Hydraulic Diagram - Hydrocontrol, single-circuit fixed 6 fcts. RC med HDL (2 EXV: Grab & Rotator) ........................................................................................................................................................211730 MCS - Hydraulic Diagram - Stablilizer circuit – 2 fcts. ........................................................................221730 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. ........................................................................231730 MCS - Hydraulic Diagram, Stabilizer circuit, 4 fcts RC .......................................................................241730 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. ...........................................251730 MCS - Hydraulic Diagram, Stabilizer circuit, 4 fcts + 4 available fcts RC ...........................................261730 MCS - Hydraulic Diagram - Hydrocontrol, single-circuit fixed6 fcts. Std./HS, std./HS dir. valve contr. HDL (2 EXV: Grab + Rotator) .......................................................................................................................27
Section - 4 29
1730 MCS - Lubrication Instructions ............................................................................................................30
Section - 4 35
1730 MCS - Dimension Sketch ....................................................................................................................361730 MCS - Slewing Radius ........................................................................................................................371730 MCS - Dimension Sketch for Truck Mounted Loader ..........................................................................381730 MCS - Lifting Height at Column ..........................................................................................................391730 MCS - Fixed Stabilizer Legs ...............................................................................................................401730 MCS - Swing-Up Stabilizer Legs 20̊ - 60̊ (Manual) .............................................................................421730 MCS - Swing-Up Stabilizer Legs 20̊ - 60̊ (Manual) .............................................................................431730 MCS - Dimension Sketch, Swing-Up Stabilizer Legs 180 (Manual & Hydraulic) ................................441730 MCS - Dimension Sketch, TS, Top Seat (RC).....................................................................................461730 MCS - Dimension Sketch, TS, Top Seat (HC Linear)..........................................................................471730 MCS - Dimension Sketch, TS, Top Seat (Danfoss X) .........................................................................481730 MCS - Dimension Sketch, TS Top Seat, (HC X) .................................................................................491730 MCS - Dimension Sketch, Ladder for TS ............................................................................................501730 MCS - Technical Data .........................................................................................................................511730 MCS - Dimension Sketch, Winch ........................................................................................................521730 MCS - Dimension Sketch, Stand-Up Platform (Standard) ..................................................................531730 MCS - Dimension Sketch, Stand-Up Platform (Valve Control) ...........................................................541730 MCS - Dimension Sketch, Internal Hose Routing) ..............................................................................55
iv
1730 MCS - Manual # 99906495
1730 MCS - Stowed in Truck Body ..............................................................................................................561730 MCS - Dimension Sketch for Connecting Link ....................................................................................571730 MCS - Cneter of Gravity ......................................................................................................................58
This page left intentionally blank
v
1730 MCS - Manual # 99906495
This page left intentionally blank
vi
1730 MCS - Manual # 99906495
Section - 1 1 1730 MCS - Technical Specifications
1730 MCS - Manual # 99906495
Section - 11730 MCS - Technical Specifications
Section - 1 2 1730 MCS - Technical Specifications
1730 MCS - Manual # 99906495
1730 - Specifications
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3Load moment ft-lb 116213 112604 109717 106829 103942 101777Hydraulic reach ft 20.7’ 27.6’ 34.4’ 42’ 49.2’ 56.8’ Hydraulic telescopic movement in 76” 155” 237” 324” 409” 495”
Lifting capacity, hydraulic lb-ft 8267 - 14.1’ 7959 - 14.1’ 7606 - 14.4’ 7275 -14.8’ 6967 - 15.1’ 6702 - 15.1’
5710 - 20.3’ 5423 - 20.7’ 5115 - 20.7’ 4828 - 21.0’ 4564 - 21.3’ 4321 - 21.7’
4079 - 27.2’ 3792 - 27.2’ 3505 - 27.6’ 3263 - 27.9’ 3042 - 28.2’
2998 - 34.1’ 2712 - 34.4’ 2491 - 34.8’ 2271 - 35.1’
2227 - 41.7’ 1984 - 42.0’ 1786 - 42.3’
1676 - 48.9’ 1477 - 49.2’
1279 - 56.4’
Lifting capacity, manual extensions
lb-ft 3086 - 31.1’ 2315 - 41.7’ 1742 - 49.2’ 1345 - 56.4’ 992 - 64.3’
2403 - 41.3’ 1830 - 49.2’ 1367 - 57.1’ 992 -64.3’ 1874 - 49.2’ 1455 - 56.8’ 992 - 64.6’
Slewing torque, gross lb-ft 12981Slewing angle ° 400°Max. heel at max. load moment ° 5
Slewing speed °/s 24
Minimum Chassis SpecsFront Axle Rating (GAWR) 12000 lbs (5,443 kg)Rear Axle Rating (GAWR) 21,000 lbs (12,981 kg)Resistance to Bending Moment 1,755,000 in-lbs (20,220 kg-m)
1) Weights ± 5% because of tolerances for plate thickness.
Section - 1 3 1730 MCS - Technical Specifications
1730 MCS - Manual # 99906495
1730 - Specifications - Continued
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis in 89”Width in 99”Width with extra valves (int. hose routing) in 100”Length, no extra valves in 32.5”Length, with extra valves (hose guides) in 37.4”Length, with extra valves (int. hose routing) in 32.5”
Stabilizer spread, S1 (standard) in 181”
Stabilizer spread, S2 in 220”
Stabilizer spread, D in 254”
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers lb 3020 3329 3638 3935 4200 4409Stabilizers, S1 fixed lb 441Stabilizers, S1 swing-up lb 452Stabilizers, S1 hydr. swing-up lb 474Stabilizers, S2 fixed lb 518Stabilizers, S2 swing-up lb 529Stabilizers, S2 hydr. swing-up lb 551Stabilizers, D fixed lb 661Stabilizers, D swing-up lb 694Mounting kit, 4 bolts lb 121Mounting kit, 8 bolts lb 132Tank, excl. oil (fitted on loader) lb 99Manual extensions
lb
187165143
16514399
1439988
9988
88
Oil in loader (stowing position) lb 66 77 88 99 110 110
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 4 1730 MCS - Technical Specifications
1730 MCS - Manual # 99906495
1730 - Specifications - Continued
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. lb 132Stand-up controls (HS), direct valve control lb 154Top seat (TS) lb 198Top seat, ladder bl 441 extra valve, hose routing lb 88 121 143 165 187 2091 extra valve, int. hose routing lb 165 165 165 176 176 1872 extra valves, hose guides lb 132 165 198 231 265 2982 extra valves, int. hose routing lb 287 287 087 309 320 353Winch (1.5 t), single snatch block lb 386 386 386 386 386 397
Winch (1.5 t), double snatch block lb 375 375 375 375 375 386
Winch (2.5 t), single snatch block lb 441 441 441 441 441 452
Winch (2.5 t), double snatch block lb 430 430 430 430 430 441
High-pressure filiter lb 15
Oil cooler lb 55
Max. Load on stabilizers (per stabilizer cylinder) Unit K1 K2 K3 K4 K5 K6
S1, fixed ft-lb 19108S1, swing-up ft-lb 19108S1, hydr. swing-up ft-lb 19108S2, fixed ft-lb 19108S2, swing-up ft-lb 19108S2, hydr. swing-up ft-lb 19108D, fixed ft-lb 15287D, swing-up ft-lb 15287D, hydr. swing-up ft-lb 15287
Power consumption (oil capacity) Unit K1 K2 K3 K4 K5 K6Working pressure psi 4786Tank capacity (fitted on loader) gal 24Max. pump performance, Hydrocontrol, 1-circuit g/min 13Max. pump performance, Hydrocontrol, 2-circuit g/min -
Section - 1 5 1730 MCS - Technical Specifications
1730 MCS - Manual # 99906495
1730 - Specifications - Metric
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3Load moment tm 16.1 15.6 15.2 14.8 14.4 14.1Hydraulic reach m 6.3 8.4 10.5 12.8 15. 17.3Hydraulic telescopic movement mm 1930 3940 6040 8203 10390 12580
Lifting capacity, hydraulic kg-m 3750 - 4.3 3610 - 4.3 3450 - 4.4 3300 - 4.5 3160 - 4.6 3040 - 4.6
2590 - 6.2 2460 - 6.3 2320 - 6.3 2190 - 6.4 2070 - 6.5 1960 - 6.6
1850 - 8.3 1720 - 8.3 1590 - 8.4 1480 - 8.5 1380 - 8.6
1360 - 10.4 1230 -10.5 1130 - 10.6 1030 - 10.7
1010 - 12.7 900 - 12.8 810 - 12.9
760 - 14.9 670 - 15
580 - 17.2
Lifting capacity, manual extensions
1400 - 10.4 1050 - 12.7 790 - 15 610 - 17.2 450 - 19.6
1090 - 12.6 830 -15.0 620 - 17.4 450 - 19.6850 - 15.0 660 - 17.3 450 - 19.7
Slewing torque, gross 17.6 17.6 17.6 17.6 17.6 17.6Slewing angle ° 400°Max. heel at max. load moment ° 5
Slewing speed °/s 24
Section - 1 6 1730 MCS - Technical Specifications
1730 MCS - Manual # 99906495
1730 MCS - Specifications - Continued
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis mm 2250Width mm 2500Width with extra valves (int. hose routing) mm 2535Length, no extra valves mm 825Length, with extra valves (hose guides) mm 950Length, with extra valves (int. hose routing) mm 825Stabilizer spread S1 (standard) mm 4615
Stabilizer spread, S2 mm 5590
Stabilizer, spread D mm 6470
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers kg 1370 1510 1650 1785 1905 2000Stabilizers S1 fixed kg 200Stabilizers S1 swing-up kg 205Stabilizers, hydr. swing-up kg 215Stabilizer S2 fixed kg 235Stabilizers S2 swing-up kg 240Stabilizers, S2 hydr. swing-up kg 250Stabilizers, D fixed kg 300Stabilizers, D swing-up kg 300Stabilizers, D hydr. swing-up kg 315Mounting kit, 4 bolts kg 55Mounting kit, 8 bolts kg 60Tank, excl. oil (fitted on loader) kg 45Manual extensions kg 85 75 65 45 40
kg 75 65 45 40kg 65 45 40
Oil in loader (stowing position) kg 30 35 40 45 50 50
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 7 1730 MCS - Technical Specifications
1730 MCS - Manual # 99906495
1730 - Metric Specifications - Continued
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. kg 60Stand-up controls (HS), direct valve control kg 70Top seat (TS) kg 90Top seat, ladder kg 201 extra valve, hose guides kg 40 55 65 75 85 951 extra valve, int. hose routing kg 75 75 75 80 80 852 extra valves, hose guides kg 60 75 90 105 120 1352 extra valves, int. hose routing kg 130 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 175 175 175 175 180Winch (1.5 t), double snatch block kg 170 170 170 170 170 175Winch (2.5 t), single snatch block kg 200 200 200 200 200 205Winch (2.5 t), double snatch block kg 195 195 195 195 195 200High-pressure filiter kg 7Oil cooler kg 25
Max. Load on stabilizers (per stabilizer cylinder) Unit K1 K2 K3 K4 K5 K6
S1, fixed kN 85 85 85 85 85 85S1, swing-up kN 85 85 85 85 85 85S1, hydr. swing-up kN 85 85 85 85 85 85S2, fixed kN 85 85 85 85 85 85S2, swing-up kN 85 85 85 85 85 85S2, hydr. swing-up kN 85 85 85 85 85 85D, fixed kN 68 68 68 68 68 68D, swing-up kN 68 68 68 68 68 68D, hydr. swing-up kN 68 68 68 68 68 68
Power consumption(oil capacity) Unit K1 K2 K3 K4 K5 K6Working pressure Bar 330Tank capacity (fitted on loader) L 90Max. pump performance, Hydrocontrol, 1-circuit L/min 50Max. pump performance, Hydrocontrol, 2-circuit L/min -
This page left intentionally blank
8
1730 MCS - Manual # 99906495
Section - 2 9 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
Section - 21730 MCS - K1-K6 Load Capacity Charts
Section - 2 10 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
1730 MCS - Lifting Capacity Chart, K1
Model 1730 MCS K1 K1
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL6-28-2019 DECAL- CP 1730 MCS - K1
BKS
70490261
70490261
4210
1910
3’ 3” 6’ 6” 9’ 8” 13’ 1” 16’ 4” 19’ 7” 23’ 0”0
0
(1m)
3’ 3”(1m)
(2m)
6’ 6”(2m)
(3m)
9’ 8”(3m)
(4m)
13’ 1”(4m)
(5m)
16’ 4”(5m)
(6m)
19’ 7”(6m)
(7m)
23’ 0”(7m)
26’ 3”(8m)
29’ 5”(9m)
lb
kg
12787
5800
8267
3750
5710
2590
Section - 2 11 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
1730 MCS - Lifting Capacity Chart, K2
Model 1730 MCS K2
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL6/28/2019 DECAL- CP1730 MCS K2
BKS
70490262
70490262
lb
kg
3’ 3” 6’ 6” 9’ 8” 13’ 1” 16’ 4” 19’ 7” 23’ 0” 26’ 2”0
0
(1m)
3’ 3”(1m)
(2m)
6’ 6”(2m)
(3m)
9’ 8”(3m)
(4m)
13’ 1”(4m)
(5m)
16’ 4”(5m)
(6m)
19’ 7”(6m)
(7m)
23’ 0”(7m)
(8m)29’5”(9m)
26’ 3”(8m)
29’ 5”(9m)
32’ 8”(10m)
36’ 1”(11m)
12566
5700
7959
3610
5423
2460
4079
1850
Section - 2 12 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
1730 MCS - Lifting Capacity Chart, K3
Model 1730 MCS K3
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL11/17/2017 DECAL- CP1730 MCS K3
BKS
70490263
70490263
(1m) (2m) (3m) (4m) (5m) (6m) (7m) (8m) (9m) (10m) (11m)0
0
3’ 3 6’ 6” 9’ 8” 13’ 1” 16’ 4” 19’ 7” 23’ 0” 26’ 2” 29’ 5” 32’ 8” 36’ 0”
(1m)3’ 3”
(2m)6’ 6”
(3m)9’ 8”
(4m)13’ 1”
(5m)16’ 4”
(6m)19’ 7”
(7m)23’ 0”
(8m)26’ 2”
(9m)29’ 5”
(10m)32’ 8”
(12m)39’ 4”
(13m)42’ 7”
(11m)36’ 1”
12125
5500
7606
3450
5115
2320
3792
1720
2998
1360
lb
kg
Section - 2 13 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
Model MCS 1730 K4
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL7/1/2019 DECAL- CP1730 MCS K4
BKS
70490264
70490264
(1m)(2m)
(3m)(4m)
(5m)(6m)
(7m)(8m)
(9m)(10m)
(11m)(12m)
0
0
3’ 2”6’ 5”
9’ 8”13’ 8”
16’ 4”19’ 6”
22’ 9”26’ 2”
29’ 5”32’ 8”
36’ 0”39’ 3” (13m)
42’ 6”
(1m)3’ 2”
(2m)6’ 5”
(3m)9’ 8”
(4m)13’ 8”
(5m)16’ 4”
(6m)19’ 6”
(7m)22’ 9”
(8m)26’ 2”
(9m)29’ 5”
(10m)32’ 8”
(14m)45’ 9”
(16m)52’ 4”
(15m)49’ 2”
(13m)42’ 6”
(12m)39’ 3”
(11m)36’ 0”
KG
11464
5200
9149
4150
7275
3300
4828
2190
3505
1590
2712
1230
2227
1010
LB
1730 MCS - Lifting Capacity Chart, K4
Section - 2 14 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
1730 MCS - Lifting Capacity Chart, K5
Model 1730 MCS K5
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL7/1/2019 DECAL- CP1730 MCS K5
BKS
70490265
70490265
(1m)(2m)
(3m)(4m)
(5m)(6m)
(7m)(8m)
(9m)(10m)
(11m)(12m)
0
0
3’ 2”6’ 5”
9’ 8”13’ 8”
16’ 4”19’ 6”
22’ 9”26’ 2”
29’ 5”32’ 8”
36’ 0”39’ 3” (13m)
42’ 6”
(14m)42’ 6” (15m)
42’ 6”
(16m)42’ 6”
(1m)3’ 2”
(2m)6’ 5”
(3m)9’ 8”
(4m)13’ 8”
(5m)16’ 4”(6m)19’ 6”(7m)22’ 9”(8m)26’ 2”(9m)29’ 5”
(10m)32’ 8”
(14m)45’ 9”
(16m)52’ 4”
(18m)59’ 1”
(17m)55’ 8”
(15m)49’ 2”
(13m)42’ 6”
(12m)39’ 3”
(11m)36’ 0”
LB
KG
11244
5100
6967
3160
4564
2070
3263
1480
2491
1130
1984
900
1676
760
Section - 2 15 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
1730 MCS - Lifting Capacity Chart, K6
Model 1730 MCS K6
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL7/1/2019 DECAL- CP1730 MCS K6
BKS
70490266
70490266
(1m)
(2m)
(3m)
(4m)
(5m)
(6m)
(7m)
(8m)
(9m)
(10m)
(11m)
(12m)
0
0
3’ 2”
6’ 5”
9’ 8”
13’ 8”
16’ 4”
19’ 6”
22’ 9”
26’ 2”
29’ 5”
32’ 8”
36’ 0”
39’ 3”(13m)42’ 6”
(14m)45’ 6”
(15m)49’ 2Z”
(17m)55’ 8”
(16m) (18m)42’ 6” 59’ 1”
(1m)3’ 2”
(2m)6’ 5”
(3m)9’ 8”
(4m)13’ 8”
(5m)16’ 4”
(6m)19’ 6”
(7m)22’ 9”
(8m)26’ 2”
(9m)29’ 5”
(10m)32’ 8”
(14m)45’ 9”
(16m)52’ 4”
(18m)59’ 1”
(19m)59’ 1”
(20m)59’ 1”
(17m)55’ 8”
(15m)49’ 2”
(13m)42’ 6”
(12m)39’ 3”
(11m)36’ 0”
LB
KG
11244
5100
6702
3040
4321
1960
3042
1380
2271
1030
1786
810
1477
670
1279
580
7231
3280
Section - 2 16 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
1730 MCS - Lifting Capacity Chart, K8
1360
K1
K2
K3
K4
K5
K6
M 4,3 6,2
10901400
1050
850
2320 830
M 4,3 6,3 8,3 10,4 12,6 15,0
19,61380 4505801960 076 8103040 0301
M 4,6 6,5 8,5 10,6 12,8 14,9 17,2 19,61480 054 2070 610067 3160 9000311
M 4,5 6,4 8,4 10,5 12,7 15,0 17,4 19,71590 450026 2190 7900101 3300 1230
M 4,4 6,3 8,3 10,4 12,7 15,0 17,31720 660
KG
KG
KG
KG 3450
KG 3610 2460 1850
KG 3750 2590
Lifting capacity with man. extensions
capacity without man. extensionsLifting
FT LB 8267 5710
14.1’ 20.3’
24033086 1874 14.1’
20.7’
27.2’
34.1’
41.3’
49.2’
LB 7959 5423 4079FT
23152998 1455 14.4’
20.7’
27.2’
34.1’
41.7’
56.8’
1830 49.2’
LB 7606 5115 3792FT
22272712 1367 14.8’
21.0’
27.6’
34.4’
41.7’
56.1’
64.6’
1742 49.2’
LB 7275 4828 3505FT
992
19842491 1345 15.1’
21.3’
27.9’
34.8’
42’ 56.4’
64.3’
1676 48.9’
LB 4564 3263FT
9926967
17862271 1279 15.1’
21.7’
28.2’
35.1’
42.3’
56.4’
64.3’
1477 49.2’
LB 4321 3042FT
9926702
4.6 6.6 8.6 10.7 12.9 15.0 17.2M
Section - 2 17 1730 MCS - K1-K6 Load Capacity Charts
1730 MCS - Manual # 99906495
1730 MCS - Lifting Capacity with WinchHydraulic hoist type
90°
0°
65°
Not recommended working angle.
MAXW MAXWD
Dinamic S 25Brevini 2500
Dinamic P9E Dinamic P15E
3307 lb
5512 lb
7055 lb
6614 lb
11023 lb
14110 lb
This page left intentionally blank
18
1730 MCS - Manual # 99906495
Section - 3 19 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
Section - 31730 MCS - Hydraulics
Section - 3 20 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Pressure setting diagram, fixed flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction Port 1730 MCS K1-K6(PSI)
1730 MCS K1-K6 (METRIC)(BAR)
Main-relief valve 4786 330
Slewing systemRight A P PLeft B P P
Boom cylinderUp A 1450 100Down B 4931 340
Jib cylinderUp A 4931 340Down B 2901 200
Extension cylindersExtend A P PRetract B P P
Grab / Flyjib lift*Up A 2901 200Down B 2901 200
Rotator / Fly-jib ext. cylinders*Extend A 2901 200Retract B 2901 200
Separate stabilizer valve All 2176 150
Working Pressure on Load-holding Valves
Function Direction Port Opening pressure [PSI]
Opening pressure [BAR]
Slewing system 2683 185Boom cylinder 5076 350Jib cylinder 5076 350
Extension cylindersRetract A 3046 210Extend B 6237 430
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 4641 320HDL 4206 290
Max. pump performancePump performance, 1-circuit 725 50Pump performance, 2-circuit - -
Section - 3 21 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Hydraulic Diagram - Hydrocontrol, single-circuit fixed 6 fcts. RC med HDL (2 EXV: Grab & Rotator)
Option
A-PORT
A-PORT
A-PORT
A-PORT
C2 C1
V2 V1
5904
4
Q-MODULT
P
5526
1 / 5
5262
A1 B1
A B
A-PORT
A-PORT
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
PstHPCO
M
A5
B5
A2
B2
A3
B3
A4
B4
A1
B1
A6
B6
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
NEM
-MO
DU
L
TP
55265 / 55266 / 55267
Tst
B1M3B
A
M2
M1
A1
55227
Max 3 bar
Section - 3 22 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Hydraulic Diagram - Stablilizer circuit – 2 fcts.
PstTst
A-PORT
A2 B2
A-PORT
A1 B1
5522
5
PT
5849
6
5849
6
Section - 3 23 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts.
PstTst
D
C
5522
8
5849
6
5849
6
D
C
5522
8
A14 B14 A13 B13 A12 B12 A11 B11
5522
6 / 5
5281
PT
A-PORT A-PORT A-PORTA-PORT
Section - 3 24 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Hydraulic Diagram, Stabilizer circuit, 4 fcts RC
D
C
5522
8
5849
6
5849
6
D
C55
228
PstTst
A13 B13 A12 B12
5527
6
T
B-PORT
A-PORT
A11 B11
PA-PORT
B-PORT
NEM-MODULPT
T
ø1 mmø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
49187
49187
Only when HR stabilizer
Section - 3 25 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts.
D
C55
228
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
A15 B15 A14 B14 A13 B13 A12 B12
5527
7
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
PA-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Section - 3 26 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Hydraulic Diagram, Stabilizer circuit, 4 fcts + 4 available fcts RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
P
P
A15 B15 A14 B14 A13 B13 A12 B12
5527
5
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
A-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
NEM-MODULT
T
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Only when HR stabilizer
49187
49187
Section - 3 27 1730 MCS - Hydraulics
1730 MCS - Manual # 99906495
1730 MCS - Hydraulic Diagram - Hydrocontrol, single-circuit fixed6 fcts. Std./HS, std./HS dir. valve contr. HDL (2 EXV: Grab + Rotator)
A-PORT
A-PORT
A-PORT
A-PORT
C2 C1
V2 V159
044
Q-MODULT
P
A-PORT
A-PORT
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
PstHPCO
M
A5
B5
A2
B2
A3
B3
A4
B4
A1
B1
A6
B6
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
Option
Tst
55255 / 55256 / 55257 / 55258 / 55259 / 55260 / 55272 / 55273 /
55274
V
P
T
MM1
5901
8
B1M3B
A
M2
M1
A1
55227
5526
1 / 5
5262
A1 B1
A B
5051
7
5051
7
Option
This page left intentionally blank
28
1730 MCS - Manual # 99906495
Section - 4 29 1730 MCS - Service Information
1730 MCS - Manual # 99906495
Section - 41730 MCS - Service Information
Section - 4 30 1730 MCS - Service Information
1730 MCS - Manual # 99906495
1730 MCS - Lubrication Instructions
Please read and follow the instructions for recommended oil and greasing in this sectionThe 1730 MCS K1-K6 are mainly equiped with maintenance-free composite bearings; however, for a limited number of bearings, regular greasing is required. The crane has to be greased in the following areas:
1. Central greasing on the base2. The push rods at the boom and jib cylinders.3. Sliding surfaces in the boom system.
Central Lubrication on the Base:
The base is equipped with a central greasing point where all lubrication of moving parts in theslewing system is carried out.The central greasing point is placed on the cross beam of the base and is indicated in the figurebelow.
Greasing has to be carried out at the greasing points indicated above, while the crane is swungfrom stop to stop. Repeat the lubrication of the cogging twice. The crane has to be lubricatedagain after 50 hours of operation or as a minimum every month. Furthermore the crane has to belubricated right before a longer period of standstill.
Figure 1 - Central greasing point on the base
Top bearing
Guide for rack
Top bearing
CoggingBottombearing
Section - 4 31 1730 MCS - Service Information
1730 MCS - Manual # 99906495
Below is indicated where the central greasing points are connected on the central part of thebase.
Push Rods at the Boom and Jib Cylinders:
Lubricate the crane’s push rods at the boom cylinder at the points indicated below. They have tobe greased after 250 hours of operation or every third month as a minimum.
Below is indicated where the central greasing points are connected on the central part of the base.
Figure 2 – Connection points on the central part of the base.
Cogging
Top bearing (2 places)
Guide for rack
Bottombearing
Figure 3 - Greasing points on inner push rods at the boom cylinder
Greasing points on the push rod
Section - 4 32 1730 MCS - Service Information
1730 MCS - Manual # 99906495
NOTE:The 1310K, 1430K, 1530K, 1510K, 1730K, 1830K, 1810K, 2030K, 2130, 2210K, 2430K, 2630KSeries only have a push rod at the jib cylinder.
Lubricate the crane’s outer push rod at the jib cylinder at the points indicated below. They have tobe greased after 250 hours of operation or every third month as a minimum.
Pins on the Main Boom:
Lubricate the pins of the crane on the main boom at the points indicated below. They have to begreased after 250 hours of operation or every third month as a minimum.
Figure 4 – Greasing points on outer push rod at the jib cylinder
Greasing points on the outer push rod
Greasing points on the push rod
Section - 4 33 1730 MCS - Service Information
1730 MCS - Manual # 99906495
Pins on the Main Boom:
Grease the boom system on all surfaces where the bearing slide blocks are running. I.e. greasethe extensions externally on the underside and internally on the upper side.
Figure 5 - Boom system with indication of greasing points
Grease the external underside
Grease the internal upper side.
This page left intentionally blank
34
1730 MCS - Manual # 99906495
Section - 5 35 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
Section - 51730 MCS - Dimension Drawings
Section - 5 36 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch
All dimension sketches are in millimeters & inches unless stated differently.
74
28,5
2062
2526
1824
2135
1175
2350
238 CL CHASSIS
80 (TYP.)
2368
4160
341
868
747
A
TOP CHASSIS
A
A-ATOP CHASSIS
TOP CHASSIS
92.5”
46.3”
9.4”
34.2”
29.4”
13.4”
163.8”
2.9”
81.2
”
81.2
”
93.2
”
95.5
” 3.1”
84”
Section - 5 37 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Slewing Radius
R545
R428
R397
R341
10°
1683
2037
2075
2251
TOP CHASSIS
21.4”
16.8”
15.6”
66.2
”
80.2
”
81.6
”
88.6
”
13.4”
Section - 5 38 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 - Dimension Sketch for Truck Mounted Loader
Max.32 Max.32
Max.160
26
80
185
40
717
357
Min.580
Max.1060
Min.900/Max.1040
717
357
38 38
Min
.200
/Max
.560
140
1)
1)1)
See note 2)
Mounting kit 8 x M24x2 bolts
Mounting kit 4 x M30x2 bolts
Notes:
1) Values dictated by strength considerations.
2) Drill hole when assembling
3) As regards installation - please see HMF Installation Manual
4) Mounting kits or spare parts - please see the Spare Parts Catalogue of the individual loader
CL CHASSIS5.5”
28.2
”14
.1”
22.8”
41.7”
7.3”
Max 6.3”
1.6”
Max 1.3” Max 1.3”
Min 35.4” / Max 40.9”
1.5” 1.5”
Section - 5 39 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Lifting Height at Column
H1K1 2,94m
K2 2,84m
K3 2,74m
K4 2,64m
K5 2,54m
2,2m
R=1m
H1
TOP CHASSIS
H1K1
K2
K3
K4
K5
9.6’
9.3’
9.0’
8.7’
8.3’
7.2’
Feet Meters
Section - 5 40 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Fixed Stabilizer Legs
A 777 877 977
520
A A52
0
290 CL CHASSIS
1625 2340 1625
5590
290 CL CHASSIS
1137 11372340
4614
A52
0
A52
0
2065 2340 2065
6470
520
520
AA 290 CL CHASSIS
TOP CHASSIS
TOP CHASSIS
TOP CHASSIS
A 30.6” 34.5” 38.5”
254”
92”
92”
92”
220”
64” 64”
3.7”3.7”
15’1
20.5
”
20.5
”
11.4”
11”
11”
20”
20”
20”
20”
81” 81”
InchesMetricmm
Section - 5 41 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Fixed Stabilizer Legs (continued)
677
440
4610 / 5590 / 6470
195
290
360
357
TOP CHASSIS
Stabilizer cylinder, C80-440
17.3
”26
.7”
181” / 220” / 254”
14”
14.1
”11
.4”
7.6”
Section - 5 42 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Swing-Up Stabilizer Legs 20̊ - 60̊ (Manual)
290 CL CHASSIS
1625 2322 16255572
A52
0
A52
0
290 CL CHASSIS
A52
0
A52
0
23211137 11374595
2065
520
2322 2065
520
6452
AA
290 CL CHASSIS
Type R-20° (Obsolete)
Type R-60°
A
971
963
871
863
771
763
TOP CHASSIS
TOP CHASSIS
TOP CHASSIS
AType R-20° (Obsolete)
Type R-60°
A
A 30.4”
30.0”34.3”34.0”
38.2”37.9”
20”
20”
20”
20”
20”
20”
11”
11”
11”
44” 44”91”180”
64” 64”
219”
91”
91”
254”
81” 81”
Inches mm
Section - 5 43 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Swing-Up Stabilizer Legs 20̊ - 60̊ (Manual)
BC C
B30°60°
20°
D
95
95
195290
360357Type R-60°
Type R-20° (Obsolete)
C
B
918
565
831
515
744
465
412378344D
C
B
D
Inches Metric mm
18.3”
29.3”
13.5”
20.3”
32.7”
14.9”
22.9”
36.1”
16.2”
3.7”
3.7”
14” 14.1”11”
7.6”
Section - 5 44 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, Swing-Up Stabilizer Legs 180 (Manual & Hydraulic)
290 CL CHASSIS
A41
8
A41
8
1625 2320 16255570
290 CL CHASSISA52
0
A52
0
23191137 1137
4593
2065
6450
2320 2065
418
A A41
8
290 CL CHASSIS
TOP CHASSIS
TOP CHASSIS
A 881 981 1081A 34.7” 38.6” 42.6”
InchesMetricmm
254”
81”
81” 81”
81”91”
91”
16”
16”
16”
16”
11”
11”
11”
219”
91”181”
45” 45”
20”
20”
Section - 5 45 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
Continued
B
6553 63
150
95
195
290
357
360
TOP CHASSIS
B 775 875 975B 30.5” 34.4” 38.4”
6”
2.5”
4”
2.1”
2.4”
InchesMetricmm
14”
14”
14.1
”
8”
Section - 5 46 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, TS, Top Seat (RC)
785
870
475
1530
490
2330
R10
20
R10
80
1200
34”
31”
19”
60”
19”
92”
47”
Section - 5 47 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, TS, Top Seat (HC Linear)
785
870
475
1530
490
2330
R10
20
R10
80
1200
34”
31”
60”
19”
18.7”
92”
47”
Section - 5 48 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, TS, Top Seat (Danfoss X)
800
890
615
1410
500
2220
20
1480
R11
90
R11
40
35”
31.5” 24.2”
19.7
”55
.5”
58.3
”
0.8”
87.4
”
Section - 5 49 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, TS Top Seat, (HC X)
735
825
585
1410
400
R11
35
R119
5
1325
32.5”
28.9” 23”
15.7
”55
.5”
52.2
”
Section - 5 50 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, Ladder for TS
NOTE:1. LADDER CANNOT BE USED FOR TS RC.2. THERE IS NO ACCESS TO THE TOP SEAT WHEN THE LOADER IS IN STOWING POSITION.
1230
520
TOP CHASSIS
48.4
”
Section - 5 51 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Technical DataPerformance (at 2176 psi) 50Unit30 1.5T Winch 2.5T WinchMax. wire pull – 1st layer 30lb40 3307 5512Max. wire pull – 2nd layer lb 3020 5071Max. wire pull – 3rd layer lb 1260 4630Max. wire pull – 4th layer lb 1170 4300Wire Speed (at 10.6 gpm) Unit 1.5T Winch 2.5T WinchMax. wire speed – 1st layer gpm 72 79Max. wire speed – 2nd layer gpm 79 85Max. wire speed – 3rd layer gpm 85 92Max. wire speed – 4th layer gpm 92 98Weights Unit 1.5T Winch 2.5T WinchTare weight, winch (CE) lb 143 198Fixed parts (valve section, brackets, hoses etc.) lb 110 110Wire Ø.39 in x 164 ft lb 66 66Spare parts, single snatch block lb 66 66Spare parts, double snatch block lb 88 88
METRICPerformance (at 150 bar): Unit 1,5T Winch 2,5T WinchMax. wire pull – 1st layer kg 1500 2500Max. wire pull – 2nd layer kg 1370 2300Max. wire pull – 3rd layer kg 1260 2100Max. wire pull – 4th layer kg 1170 1950Wire Speed (at 40 L/min) Unit 1,5T Winch 2,5T WinchMax. wire speed – 1st layer m/min 22 24Max. wire speed – 2nd layer m/min 24 26Max. wire speed – 3rd layer m/min 26 28Max. wire speed – 4th layer m/min 28 30Weights Unit 1,5T Winch 2,5T WinchTare weight, winch (CE) kg 65 90Fixed parts (valve section, brackets, hoses etc.) kg 50 50Wire Ø10 x 50 m kg 30 30Spare parts, single snatch block kg 30 30Spare parts, double snatch block kg 40 40
Section - 5 52 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, Winch
2,5T: , 925mm1,5T: , 945mm
1010
37.2”36.4”
Ø.39Ø.39
Section - 5 53 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, Stand-Up Platform (Standard)
1821
850
555
TOP CHASSIS
33.5”
71.7
”
21.9
”
Section - 5 54 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, Stand-Up Platform (Valve Control)
151
5
875 2
75
TOP CHASSIS
34.4”
59.6
”
10.8
”
Section - 5 55 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch, Internal Hose Routing)
B
252
2
A
D
øD A B
K1, K2, K3 480 210mm 86mm
K4 520 230mm 66mm
K5 570 255mm 41mm
K6 620 280mm 16mm
øD A B
K1, K2, K3
K4
K5
K6
18.9”
20.4”
22.4”
24.4”
8.3”
9.1”
10”
11”
3.4”
2.6”
1.6”
0.6”
Metric
Inches99.2
”
Section - 5 56 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Stowed in Truck Body
15°
1333
2449
2334
2091
TOP CHASSIS
TOP CHASSIS
91.9”
52.5”
82.3” 96.4”
Section - 5 57 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Dimension Sketch for Connecting Link
Manufacturing of connecting links for crane equipment:
The following design considerations are recommended to ensure that the connecting link can swing sufficiently when using the equipment connected and when stowing in truck body and/or folding.
In general, we recommend that the connecting link can move freely in an angle of minimum 35° in both directions in relation to the longitudinal direction of the jib extension. This is to minimize the risk of damage to the hook suspension when placing crane equipment in the truck body.
Max. 26,5
Min
. 52
Max. R35
Max. 70
35°
Section
1 (1)
Technical Information 1510-K, 1730-K, 1830-K
Dimension sketch for connecting link
27-06-2017
31 087 66Date Page
Catalogue no.
Max. 1.04”
Min
. 2.0
5”
Max. R1.38”Max. 2.76”
Recommended dimensions for connecting link.(mm and inches)
Section - 5 58 1730 MCS - Dimension Drawings
1730 MCS - Manual # 99906495
1730 MCS - Cneter of Gravity
H2
V2
H1
f
H4
V2
H3
V3
V1
Z3
G2
G2
G1
G3
CL CHASSIS
]gk[]mm[V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G3
K1 165 1940 730 215 1680 355 1420 5 290 650 895 1545K2 165 2000 755 215 2390 350 1665 30 290 650 1040 1690K3 165 2045 780 215 3145 335 1850 45 290 650 1180 1830K4 165 2080 805 215 3940 320 2000 60 290 650 1310 1960K5 165 2100 825 215 4695 305 2115 75 290 650 1420 2070K6 165 2120 840 215 5340 290 2200 85 290 650 1525 2175
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G3K1 6.5”K2 6.5”K3 6.5”K4 6.5”K5 6.5”K6 6.5”
Inches lb
76.4” 66.1” 14.0” 11.4”11.4”11.4”11.4”11.4”11.4”
55.9”65.5”72.8”78.7”83.3”86.6”
13.9”13.2”12.6”12.0”11.4”
94.1”123.8”155.1”184.8”210.2”
28.7”29.7”30.7”31.7”32.5”33.1”
78.7”80.5”81.9”82.7”83.5”
8.5” 0.2”8.5” 1.2”
1.8”2.4”2.9”3.3”
8.5”8.5”8.5”8.5”
143314331433143314331433
197322932601288831313362
340637264034432145644795
IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.
IMT and IMT LOGO are registered trademarks of Iowa Mold Tooling Co., Inc., Garner, IA, USA.© 2020 Iowa Mold Tooling Co., Inc. All Right Reserved.
IOWA MOLD TOOLING CO., INC.
P.O. Box 189 Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com