1381078531 JCI Cyclonics Datasheet Vertical Recycling Cyclonic Separators
2
VERTICAL RECYCLING CYCLONIC SEPARATOR The JCI Vertical Recycling Cyclonic Separator uses two stages of separatio remove liquid and solid contaminants and achieve a high separation efficienc tangential inlet on the separator creates centrifugal force that causes the he liquid and solid particles to migrate toward the vessel wall, thus forcing the lig particles such as gas, into the center of the vessel. This gas enters the cyclone while the liquid and solid contaminant continues toward the bottom of the ve The gas stream is still spinning as it enters the cyclone tube, where liquid droplet entrained in the gas are forced to the outer wall of the tube. This liquid, along w small percentage of the gas, exit the cyclone tube and are forced through a recy system where it is reintroduced to the inlet of the cyclone tube. This recy system gives the smaller entrained droplets a second chance at separation, w increases the efficiency approximately 10% over a conventional cyclone separato The liquid chamber in the bottom of the vessel contains vortex breakers to diss energy and prevent re-entrainment. The liquid section can be sized as large small as necessary to accommodate proper retention times, and may be constru for gravity separation of immiscible liquids such as oil and water to mee customer's specific requirements. The JCI recycling cyclonic separator is able t remove the particles that are not separated with the bulk contaminants through a recyclin system. The overall separation efficiency i significantly higher than conventional cycloni separators, with minimal pressure loss. Thi improvement in performance means that the JC recycling separator can be used for bul separation and polishing in a single vessel, savin time, space, and equipment capital costs. Conventional cyclonic separators (shown left) perform adequately for bulk separation, however particles that are not separated with the bulk contaminants enter the cyclone and leave with the residual gas yielding poor separation efficiency. The residue gas typically requires additional processing downstream of a conventional cyclonic separator. JCI Cyclonics Ltd. is a Canadian manufacturer of cyclonic separation products for the Oil and Gas Industry. JCI offers engineered Flange- TM To-Flange solutions for all your cyclonic separation needs using proven technology. P R O D U C T D A T A S H E E T Tel 403.568.2031 | Fax 403.280.7926 | [email protected] | www.jcicyclonics.co Flange-To-Flange Solutions JCI Cyclonics Ltd.
Transcript of 1381078531 JCI Cyclonics Datasheet Vertical Recycling Cyclonic Separators
-
VERTICAL RECYCLINGCYCLONIC SEPARATOR
The JCI Vertical Recycling Cyclonic Separator uses two stages of separation to remove liquid and solid contaminants and achieve a high separation efficiency. A tangential inlet on the separator creates centrifugal force that causes the heavier liquid and solid particles to migrate toward the vessel wall, thus forcing the lighter particles such as gas, into the center of the vessel. This gas enters the cyclone tube, while the liquid and solid contaminant continues toward the bottom of the vessel. The gas stream is still spinning as it enters the cyclone tube, where liquid droplets still entrained in the gas are forced to the outer wall of the tube. This liquid, along with a small percentage of the gas, exit the cyclone tube and are forced through a recycling system where it is reintroduced to the inlet of the cyclone tube. This recycling system gives the smaller entrained droplets a second chance at separation, which increases the efficiency approximately 10% over a conventional cyclone separator.
The liquid chamber in the bottom of the vessel contains vortex breakers to dissipate energy and prevent re-entrainment. The liquid section can be sized as large or as small as necessary to accommodate proper retention times, and may be constructed for gravity separation of immiscible liquids such as oil and water to meet the customer's specific requirements.
The JCI recycling cyclonic separator is able to remove the particles that are not separated with the bulk contaminants through a recycling system. The overall separation efficiency is significantly higher than conventional cyclonic separators, with minimal pressure loss. This improvement in performance means that the JCI recycling separator can be used for bulk separation and polishing in a single vessel, saving time, space, and equipment capital costs.
Conventional cyclonic separators (shown left) perform adequately for bulk separation, however particles that are not separated with the bulk contaminants enter the cyclone and leave with the residual gas yielding poor separation efficiency. The residue gas typically requires additional processing downstream of a conventional cyclonic separator.
JCI Cyclonics Ltd. is a Canadian manufacturer of cyclonic separation products for the Oil and Gas Industry. JCI offers engineered Flange-
TMTo-Flange solutions for all your cyclonic separation needs using proven technology.
PROD
UCT D
ATAS
HEET
Tel 403.568.2031 | Fax 403.280.7926 | [email protected] | www.jcicyclonics.com
TMFlange-To-Flange SolutionsJCI Cyclonics Ltd.
Page 1
