13 Free Jewelry Patterns from Prima Bead.pdf
Transcript of 13 Free Jewelry Patterns from Prima Bead.pdf
-
13 FREE PATTERNS INSIDE RECEIVE A FREE GIFT WITH YOUR PURCHASE
Your coupon code is located on the back cover
$25only
CLICKABLE PATTERN BOOK VOLUME 1
800-366-2218 WWW.PRIMABEAD.COM FREE SHIPPING
shimmerClass In A Box 1,840 pcsBead Mat & 3-in-1 Tool IncludedMakes 2 Necklaces, 2 Bracelets & 2 Sets of Earrings
34706012
.COM
http://www.primabead.com/Jewelry-Class-in-a-Box-Shimmer-P8250.aspx?utm_source=PrimePub&utm_medium=Ebook&utm_content=ShimmerCIAB&utm_campaign=EbookAug14&Source=EbookAug14ShimmerCIAB
-
Shop now at www.primabead.com/bethany
CLICKHERE!
Free Shipping . 10-25% Volume Discounts . Free Patterns2
Tools Needed: Needle Nose Pliers #4454Crimping Pliers #4501 Wire Cutters #4457
Techniques to Know: Opening Jump Rings Crimp Tubes
Bethanynecklace
http://www.primabead.com/bethany?utm_source=PrimePub&utm_medium=Ebook&utm_content=Bethany&utm_campaign=EbookAug14&Source=EbookAug14Bethany
-
3
Instructions: 1. Cut the following lengths of beading
wire: a 7, a 9 and an 11 length.
2. Using crimp tubes, attach each wire to its own 4mm jump ring.
3. Thread the following pattern onto the 7 wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.
4. Thread the following pattern onto the 9 wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.
5. Thread the following pattern onto the 11 wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.
6. Using crimp tubes, attach each wire to its own 4mm jump ring. Trim the excess wire.
7. Cut (12) 8 lengths of chain.8. Attach (2) chains to each 4mm jump ring.9. Gather a set of chains from one end of each
beaded section using a 6mm jump ring. Attach a toggle clasp to the jump ring.
10. Repeat the steps for the other set of chains and clasp.
Materials:# 34713130
4mm Bronze Metallic Bicones
$4.00 (x1)
# 37450085 Purple/White Shell Bead Strand
$4.00 (x3)
# 34718104 Copper Small Chain
$4.00 (x2)
# 34719069 Copper Findings Pack
$4.00 (x1)
# 3202001 Gold 7-Strand Beading Wire
$2.00 (x1)
While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/bethany?utm_source=PrimePub&utm_medium=Ebook&utm_content=Bethany&utm_campaign=EbookAug14&Source=EbookAug14Bethany
-
Shop now at www.primabead.com/blueice
Free Shipping . 10-25% Volume Discounts . Free Patterns4
Blue Icecoin knot earrings
Materials:# 34745025
Silver Satin Cord
$3.99 (x1)
# 34745020 Blue Metallic Cord
$3.99 (x1)
# 34712124 Silver Cord Ends
$1.99 (x1)
# 34712100 Silver Earring Wires
$2.00 (x1)
Makes16 pairs
http://www.primabead.com/blueice?utm_source=PrimePub&utm_medium=Ebook&utm_content=blueice&utm_campaign=EbookAug14&source=EbookAug14BlueIce
-
CLICKHERE!
5
Instructions: 1. Cut (2) 16 lengths of metallic blue cord and
(1) 16 length of silver cord.
2. Weave the cords as a set, with silver cord on the inside. Follow the pattern as shown on our website.
3. Shift the cords to make the knot tighter and more even.
4. Bring the ends together and trim the excess.
5. Use a metal cord end to secure the cords together. Attach the earring wire to the hole of the cord end.
6. Repeat steps 1-5 for the matching earring.
Tools Needed: Needle Nose Pliers #4454Wire Cutters #4457
Techniques to Know: Opening Jump RingsCord Ends
While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/blueice?utm_source=PrimePub&utm_medium=Ebook&utm_content=blueice&utm_campaign=EbookAug14&source=EbookAug14BlueIce
-
Shop now at www.primabead.com/gemstone
Free Shipping . 10-25% Volume Discounts . Free Patterns6
Tools Needed: Round Nose Pliers #6858Wire Cutters #4457
Techniquesto Know: Wire Wrapping
Gemstone cuffbracelet
Materials:# 34698109
Gold Cuff Bracelet
$2.00 (x1)
# 34714124 Green Agate Slice
$2.00 (x1)
# 3201801 Gold 24 Gauge Wire
$2.69 (x1)
# 22279001 E6000 Glue
$3.40 (x1)
Instructions: 1. Use E6000 to adhere the accent to
the top center of the cuff. Allow the adhesive to dry thoroughly (according to manufacturers instructions) before adding the wire to prevent the agate from sliding on the cuff.
2. Cut a 36 length of gold wire.
3. Tuck one end of the wire between the gemstone and the cuff. Wrap the wire multiple times around the base of the gemstone.
4. Bring the wire up over the stone and down to one side and under the cuff, keeping the wire snug against the cuff. Continue wrapping the wire over the stone and under the cuff.
5. Tuck the end of the wire under the lip of the gemstone but not on the inside of the cuff. Apply additional adhesive to keep the wire in place.
6. Using round nose pliers, gently twist the wire along the top of the gemstone. The slight twisting tightens the wire on the gemstone.
http://www.primabead.com/gemstone?utm_source=PrimePub&utm_medium=Ebook&utm_content=gemstone&utm_campaign=EbookAug14&source=EbookAug14Gemstone
-
CLICKHERE!
7While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/gemstone?utm_source=PrimePub&utm_medium=Ebook&utm_content=gemstone&utm_campaign=EbookAug14&source=EbookAug14Gemstone
-
Shop now at www.primabead.com/blueiris
Free Shipping . 10-25% Volume Discounts . Free Patterns8
Instructions: 1. Cut (4) 50 lengths of blue metallic cord.
2. Bring the cord ends together and fold in half. Bring the fold down through the center of the round disc.
3. Cut a scrap piece of cord (4+ inches) and tie it onto the center fold from step 2.
4. Align the cords as explained in the Beaded Kumihimo instruction booklet that came with the round disc.
Materials:# 34745020
Metallic Blue Cord
$3.99 (x1)
# 34745036 Kumihimo Bobbins
$6.99 (x1)
# 34745001 Metallic Blue Rondelles
$11.99 (x1)
# 34745033 Kumihimo Round Disc
$2.99 (x1)
# 34750022 Silver Kumihimo Findings Pack
$3.99 (x1)
# 34745035 Kumihimo Beading Needle
$2.99 (x1)
# 22279001 E6000 Glue
$3.40 (x1)
5. Using the big eye beading needle, thread (30) metallic beads onto each strand. This makes an 8 bracelet with cord ends. Use less or more beads on each of the eight cords to decrease or increase the overall length.
6. Wind each of the eight cords (with beads) onto a bobbin and close.
7. Follow the beaded instructions that came with the disc. Braid the cord before adding the beads. This section will be inserted into the clasp.
8. Braid a tail after all of the beads have been braided in. Remove the cords from the bobbins and from the disc and tie them into a tight single knot. Remove the scrap cord from the other end.
9. Trim the excess cord. Next apply glue to the ends of the cords and slide the cord ends on. Allow the glue to dry according to manufacturer instructions (2+ hours).
Tools Needed: Round Nose Pliers #6858Needle Nose Pliers #4454Wire Cutters #4457
Techniques to Know: Kumihimo Round Braiding w/ Beads
http://www.primabead.com/blueiris?utm_source=PrimePub&utm_medium=Ebook&utm_content=BlueIris&utm_campaign=EbookAug14&source=EbookAug14BlueIris
-
9
Blue Iriskumihimo bracelet
While supplies last.
CLICKHERE!
Click to see this pattern on Primabead.com
http://www.primabead.com/blueiris?utm_source=PrimePub&utm_medium=Ebook&utm_content=BlueIris&utm_campaign=EbookAug14&source=EbookAug14BlueIris
-
Shop now at www.primabead.com/francesca
Free Shipping . 10-25% Volume Discounts . Free Patterns10
Francescabracelet
DRESS LIKE IT.~Lilly Pulitzer
Lifes a party,
CLICKHERE!
http://www.primabead.com/francesca?utm_source=PrimePub&utm_medium=Ebook&utm_content=Francesca&utm_campaign=EbookAug14&source=EbookAug14Fransesca
-
11
Instructions: 1. Cut (or separate using two pairs of pliers) the
large double link chain into a 6 section.
2. Attach (2) 6mm jump rings to each end of the chain.
3. Using 6mm jump rings, attach a lobster claw clasp to one set of jump rings and attach an extender chain to the other set of jump rings.
4. Make a wrapped loop bicone drop and attach the drop to the end of the extender chain.
5. Cut (2) 10 lengths of beading wire.
6. Using crimp tubes, attach each wire to a 6mm jump ring at one end of the double link chain.
7. Thread (44) bicones onto each wire.
8. Weave the bicone strands through the chain links.
9. Using crimp tubes, attach the beading wire strands to the 6mm jump rings at the end of the chain. If its too difficult to weave the loose strands of beads, try crimping the wire, leaving a small loop for the jump ring to fit though. Then weave the strands through the double link chain.
Materials:# 34721066
4mm Bicone Mix
$4.00 (x2)
# 34718096 Silver Large Double Link Chain
$4.00 (x1)
# 34719059 Silver Findings Starter Pack
$4.00 (x1)
# 3202002 Silver 7-Strand Beading Wire
$2.00 (x1)
Tools Needed: Round Nose Pliers #6858Needle Nose Pliers #4454Crimping Pliers #4501Wire Cutters #4457
Techniques to Know: Opening Jump RingsForm a Wrapped Loop
Crimp Tubes
While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/francesca?utm_source=PrimePub&utm_medium=Ebook&utm_content=Francesca&utm_campaign=EbookAug14&source=EbookAug14Fransesca
-
Shop now at www.primabead.com/caprise
Free Shipping . 10-25% Volume Discounts . Free Patterns12
CREATIVITYis an act of defiance.~Twyla Tharp
CLICKHERE!
http://www.primabead.com/caprise?utm_source=PrimePub&utm_medium=Ebook&utm_content=Caprise&utm_campaign=EbookAug14&source=EbookAug14Caprise
-
13
Instructions: 1. Using pliers, separate the chain into (28) 10-link lengths, each approximately 1 long.2. Cut (4) 14 lengths of stretch cord. Lay the (4) cords flat in a row, approximately
from each other.
3. Thread each cord through a single chain and thread a turquoise round onto cords 1 and 3.4. Thread each cord through a single chain and thread a turquoise round onto cords 2 and 4.5. Repeat steps 3-4 14 more times. Increase the overall length by repeating steps 3-4 again.6. Tie each cord together into a double knot. Trim the excess cords. The tension of the
stretch cord will move the chain so it surrounds the beads and forms a woven pattern.
Materials:# 34718010
Gold Small Curb Chain
$4.00 (x2)
# 34713033 8mm Turquoise Round Beads
$4.00 (x1)
# 3202302 .8mm Stretch Cord
$2.00 (x1)
Caprisebracelet
Tools Needed: Needle Nose Pliers #4454Wire Cutters #4457
Techniques to Know: Tying a KnotOpening Jump Rings
While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/caprise?utm_source=PrimePub&utm_medium=Ebook&utm_content=Caprise&utm_campaign=EbookAug14&source=EbookAug14Caprise
-
Shop now at www.primabead.com/crackle
Free Shipping . 10-25% Volume Discounts . Free Patterns14
Triple Cabochon Bracelet Instructions:1. Apply dabs of Quick Hold glue to a set
of round bezels and attach them to the back of an oval cabochon. Do not let the glue seep through the opening for the flat memory wire, otherwise, once the glue dries it wont allow the wire to fit. Repeat this step for the remaining two cabochons.
2. Allow the glue to dry completely before continuing the bracelet.
3. Cut (2) single coils of bracelet memory wire.
4. Slide each cabochon onto the set of wires and position them at the center.
5. Cut a 48 length of gauge wire.
6. Coil the wire onto the memory wire to the inner side of the end cabochon bezel. Coil the wire approximately (5) loops and press the coil snug. Bring the wire over the back side of the bezel and continue to coil it onto the memory wire.
Additional Patterns Available Online @ www.primabead.com/crackle
Tools Needed: Round Nose Pliers #6858Parrot Beak Pliers #4477Wire Cutters #4457
Techniques to Know: Wire Wrapping
Materials:# 74100073
Gold Flat Bracelet Memory Wire
$3.99 (x1)
# 74100061 Gold Flat Memory Wire Ends
$2.99 (x1)
# 74100068 Gold Flat Memory Wire Round Bezels
$2.99 (x1)
# 3201801 Gold 24 Gauge Wire
$2.69 (x1)
# 22279004 Quick Hold & E6000 Mini Tubes
$4.00 (x1)
# 9161 Gemocite Cabochon Mix
$8.00 (x1)
7. Coil the wire up to the bezel of the center cabochon. The sample has 1/2 of coil between each bezel. Bring the wire over the back side of the bezel and continue the coil. Repeat this step until the wire is coiled into (5) loops after the last cabochon.
8. Repeat steps 5-7 to secure the second memory wire section.
9. Size the bracelet and trim 1/2 off the total size needed for each memory wire length.
10. Using E6000, adhere the wire ends to the memory wire and allow the adhesive to dry thoroughly.
http://www.primabead.com/crackle?utm_source=PrimePub&utm_medium=Ebook&utm_content=Crackle&utm_campaign=EbookAug14&source=EbookAug14Crackle
-
15
Crackle Cabochon
jewelry
While supplies last.
CLICKHERE!
Click to see this pattern on Primabead.com
http://www.primabead.com/crackle?utm_source=PrimePub&utm_medium=Ebook&utm_content=Crackle&utm_campaign=EbookAug14&source=EbookAug14Crackle
-
Shop now at www.primabead.com/goldenflower
Free Shipping . 10-25% Volume Discounts . Free Patterns16
The constant happiness is
CURIOSITY.~Alice Munro
Makes2 bracelets
CLICKHERE!
http://www.primabead.com/goldenflower?utm_source=PrimePub&utm_medium=Ebook&utm_content=GoldenFlower&utm_campaign=EbookAug14&source=EbookAug14GoldenFlower
-
17
Large Flower Bracelet Instructions:1. Remove the chains, jump rings and
charms from the large flower. *These pieces will be used in the adjustable bracelet.
2. Cut a single coil of bracelet memory wire.
3. Form a loop to one side of the wire. Attach the smaller of the flower loops to the wire.
4. Form a partial loop at the other end of the wire, this should fit into the large loop of the flower. If the bracelet is too large, trim off a small section and form another loop.
Adjustable Flower Bracelet Instructions:1. Cut a 1 1/2 coil of bracelet memory wire,
approximately 12 in length.
2. Form a loop at each end of the wire.
3. Bend each loop inwards and overlap the loops over the opposite ends of the wire, making the bracelets adjustable.
4. Using the jump rings from the accent, attach the three charms to the bracelet.
Tools Needed: Round Nose Pliers #6858P arrot Beak Pliers #4477
*Used for Memory Wire
Techniquesto Know: Form a Loop
Materials:# 74100073
Gold Flat Memory Wire
$3.99 (x1)
# 72099305 Gold Flower Cluster Pendant
$5.99 (x1)
Golden FlowerCharmbracelets
While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/goldenflower?utm_source=PrimePub&utm_medium=Ebook&utm_content=GoldenFlower&utm_campaign=EbookAug14&source=EbookAug14GoldenFlower
-
Shop now at www.primabead.com/molly
Free Shipping . 10-25% Volume Discounts . Free Patterns18
Tools Needed: Needle Nose Pliers # 4454Wire Cutters # 4457Crimping Pliers # 4501
Techniquesto Know: Opening Jump RingsCrimp Tubes
Instructions:1. Cut (3) 10 lengths of beading wire.
2. Use a crimp tube to gather the (3) wires together and attach them to an 8mm jump ring. Connect a toggle clasp end to the same jump ring.
3. Thread each beading wire strand through the holes of a 3-strand rondelle.
4. Thread (3) blue bicones onto one of the end strands. Thread (2) blue bicones onto the middle strand. Thread (1) blue bicone onto the other end strand.
5. Thread (1) 3-strand spacer onto the beading wire strands.
6. Thread (1) mirror bead onto the strand containing (3) bicones. Thread (2) blue bicones onto the middle strand. Thread (3) mirror beads onto the strand containing (1) bicone.
7. Thread (1) 3-strand spacer onto the beading wire strands.
8. Thread (3) blue pearls onto the strand with the single mirror bead and (3) crystals. Thread (2) blue pearls onto the strand with the (2) mirror beads and (2) crystals. Thread (1) blue pearl onto the strand with the (3) mirror beads and (1) crystal.
9. Thread (1) 3-strand spacer onto the beading wire strands.
10. Continue the pattern of beads until the bracelet is at the desired length.
11. Use a crimp tube to gather the (3) wires together and attach them to an 8mm jump ring. Connect the other toggle clasp end to the same jump ring.
Materials:# 34722034
6mm Blue Pearl/Crystal Mix
$4.00 (x1)
# 34741058 6mm Dark Blue Mirror Beads
$4.00 (x1)
# 34719059 Silver Findings Starter Pack
$4.00 (x1)
# 34708262 Silver & Crystal Rondelle Spacer
$4.00 (x3)
# 34719057 Silver 8mm Jump Rings
$4.00 (x1)
# 3202002 Silver 7-Strand Beading Wire
$2.00 (x1)
http://www.primabead.com/molly?utm_source=PrimePub&utm_medium=Ebook&utm_content=Molly&utm_campaign=EbookAug14&source=EbookAug14Molly
-
While supplies last. 19
Mollybracelet
Color Schemes & Supply Variations Available Online at www.primabead.com/molly
CLICKHERE!
Click to see this pattern on Primabead.com
http://www.primabead.com/molly?utm_source=PrimePub&utm_medium=Ebook&utm_content=Molly&utm_campaign=EbookAug14&source=EbookAug14Molly
-
Free Shipping . 10-25% Volume Discounts . Free Patterns20
SharedHearts
Tools Needed: Needle Nose Pliers #4454Round Nose Pliers #6858Crimping Pliers #4501
Techniques to Know: Forming a LoopOpening Jump RingsCutting Chains
bracelet & earrings
Shop now at www.primabead.com/sharedhearts
CLICKHERE!
http://www.primabead.com/sharedhearts?utm_source=PrimePub&utm_medium=Ebook&utm_content=SharedHearts&utm_campaign=EbookAug14&source=EbookAug14SharedHearts
-
21
Materials:# 34719059
145pc Starter Pack Silver
$4.00 (x1)
# 34708289 5pc Silver Deco Heart
$4.00 (x1)
# 34718092 100 in/254cm Silver Small Curb Chain
$4.00 (x1)
# 34722035 101 pc 6mm Pearl/Crystal Mix Red
$4.00 (x1)
# 3202002 40 .3mm 7-Strand Bead Wire- Silver
$2.00 (x1)Instructions for Bracelet:1. Cut (10) 2 1/8 lengths of silver
chain. Approx. 27 links each
2. Take (5) lengths of the chain and connect each group of ends with a 2mm jump ring, then repeat with the other (5) lengths of chain.
3. Connect a 4mm jump ring to one side of each grouping of chains (this will be where you connect the toggle clasps).
4. Using the 4mm jump rings you just attached to the chain groups, connect the two ends of your toggle clasps.
5. Moving onto the center of the bracelet. Begin by cutting a 4 strand of beading wire.
6. Crimp a small loop into one end of the wire, leaving about 1 on one side and 3 inches on the other.
7. Thread the beads in this order onto the wire: bicone, heart, pearl, heart, bicone.
8. Close the other end of the wire into a loop using a crimp bead. (If you leave enough extra wire to feed back through the heart it will be easier to pull the wire and form a tighter loop).
9. Finally, connect either end of your hearts to the 2mm jump rings on the ends of your pieces from steps 1-4.
Instructions for Earrings:1. Cut (10) 1 lengths of chain. Approx. 19 links
each
2. Thread (5) lengths of chain onto a 2mm jump ring
3. Now connect the 2mm jump ring to the loop on an eye pin.
4. Thread a pearl and then a bicone onto the eye pin and create a loop on the end.
5. To make sure that your earrings hang correctly, youll need to connect a 2mm jump ring on the end of your eye pin before you connect the earring wires.
6. Now repeat steps 1-5 to make the matching earring.
While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/sharedhearts?utm_source=PrimePub&utm_medium=Ebook&utm_content=SharedHearts&utm_campaign=EbookAug14&source=EbookAug14SharedHearts
-
Shop now at www.primabead.com/turquoise
Free Shipping . 10-25% Volume Discounts . Free Patterns22
Successis liking yourself, liking what you
do, and liking how you do it.~Maya Angelou
CLICKHERE!
http://www.primabead.com/turquoise?utm_source=PrimePub&utm_medium=Ebook&utm_content=Turqouise&utm_campaign=EbookAug14&source=EbookAug14Turquoise
-
23
Tools Needed: Crimping Pliers #4501Wire Cutters #4457
Techniquesto Know: Crimp Tubes
Instructions:1. Cut (5) 12 lengths of stretch cord.
2. Using crimp tubes, attach each length of stretch cord to one end of the toggle. Use separate crimp tubes for each length of cord.
3. Thread (35) beads onto each length of stretch cord. Use less or more depending on the overall length needed.
4. Use crimp tubes to attach each length of cord to the other end of the toggle. Use separate crimp tubes for each length of cord.
5. Trim the excess cords.
TurquoiseDream
braceletMaterials:# 34719178
Cabochon Toggle
$3.00 (x1)
# 34741016 Turquoise Bicone Mirror Beads
$4.00 (x3)
# 3202302 .8mm Stretch Cord
$2.00 (x1)
# 34712131 Silver Crimp Tubes
$1.99 (x1)
While supplies last.Click to see this pattern on Primabead.com
http://www.primabead.com/turquoise?utm_source=PrimePub&utm_medium=Ebook&utm_content=Turqouise&utm_campaign=EbookAug14&source=EbookAug14Turquoise
-
Enter code above at checkout for a FREE GIFT with purchase!
COUPON CODE: ABA231
*Coupon can only be redeemed once per customer.
CLASS IN A BOXClassic#34706-009 155+ pieces!
Makes 2 Necklaces, 2 Bracelets & 2 sets of EarringsBead Mat & 3-in-1 Tool Included
$25
Casual#34706-010 230+ pieces!
Makes 2 Necklaces, 2 Bracelets & 2 sets of EarringsBead Mat & 3-in-1 Tool Included
$25
Natural#34706-011 255+ pieces!
Makes 2 Necklaces, 2 Bracelets & 2 sets of EarringsBead Mat & 3-in-1 Tool Included
$25
Let us help youCREATE BEAUTIFUL JEWELRY
ORDER ONLINEOur quick and easy checkout process
makes ordering a breeze. Place an order at www.primabead.com 24 hours a day,
7 days a week.
OVER THE PHONEOur friendly customer service team is here to assist you with placing your order. You can
reach us at 800-366-2218 between 9:00am4:30pm EST, MondayFriday.
12333 ENTERPRISE BLVD.LARGO, FL 33773
http://www.primabead.com/Jewelry-Class-in-a-Box-Classic-P8247.aspx?utm_source=PrimePub&utm_medium=Ebook&utm_content=CiabClassic&utm_campaign=EbookAug14&source=EbookAug14CiabClassichttp://www.primabead.com/Jewelry-Class-in-a-Box-Casual-P8248.aspx?utm_source=PrimePub&utm_medium=Ebook&utm_content=Ciab Casual &utm_campaign=EbookAug14&source=EbookAug14CiabCasualhttp://www.primabead.com/Jewelry-Class-in-a-Box-Natural-P8249.aspx?utm_source=PrimePub&utm_medium=Ebook&utm_content=Ciab Natural &utm_campaign=EbookAug14&source=EbookAug14CiabNatural