11.9 Dielectric Stress in a Single-Core cable
Transcript of 11.9 Dielectric Stress in a Single-Core cable
![Page 1: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/1.jpg)
11.9 Dielectric Stress in a Single-Core cable
Under operation conditions, the insulation of a cable
is subjected to electrostatic forces.
This is known as a dielectric stress, which is in fact the
potential gradient (or electric field intensity) at that
point
Consider a single-core cable as shown in Fig. 11.14
and as proved previously,
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 1
![Page 2: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/2.jpg)
Since the voltage V is given by:
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 2
![Page 3: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/3.jpg)
The variation of stress in the dialectic is shown in Fig. 11.14
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 3
![Page 4: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/4.jpg)
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 4
![Page 5: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/5.jpg)
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 5
![Page 6: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/6.jpg)
11.14 capacitance of 3-core Cables
The capacitance of a cable system is much more important than the at of overhead line because in cable:
(i). Conductors are nearer to each other and to earth sheath
(ii) They are separated by a dielectric of permittivity much greater than that of air
Fig. 11.18 shows a system of capacitance in a 3-core belted cable used for three-phase system
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 6
![Page 7: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/7.jpg)
Since potential difference exists between pairs of conductors and between each conductor and the sheath, electrostatic fields are set up in the cable as shown in Fig. 11.18 (i).
These electrostatic fields give rise to core-core capacitance CC and conductor-earth capacitance Ce as shown in Fig. 11.18 (ii).
The three CC are delta connected whereas the three Ce are star connected, the sheath forming the star point [As seen in Fig. 11.18 (iii)].
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 7
![Page 8: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/8.jpg)
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 8
![Page 9: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/9.jpg)
11.15 Measurements of Ce and Cc Although core-core capacitance Cc and core-earth capacitor Ce can be determine from the empirical formulas for belted cable, their values can also be determined by measurements.
For this purpose the following two measurements are required:
(i) The three cores are bunched together and the capacitance is measured between the bunched core and the sheath.
The bunching eliminates all the three capacitors Cc, leaving the three capacitors Ce in parallel.
Therefore, if C1 is the measured capacitance, this test yields:
C1 = 3 Ce
Or Ce = C1 / 3
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 9
![Page 10: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/10.jpg)
(ii) In the second measurement, two cores are bunched with the sheath and the capacitance is measured between them and the thirs cor.
This test yields to a value given by, C2, where C2 is given by:
C2 = 2Cc + Ce
As the value of Ce is known from the first test and C2 is found experimentally, therefore, value of Cc can be determined.
It may be noted that if value of CN (= Ce + 3 Cc) is desired, it can be found directly by another test.
In this test, the capacitor between two cores or lines is measured with the third core free or connected to the sheath.
This eliminates one of the capacitors Ce so that if C3 is the measured capacitance, then
C3 = Cc + Cc/2 + Ce/2
= ½ (Ce + 3 Cc)
= ½ CN
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 10
![Page 11: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/11.jpg)
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 11
![Page 12: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/12.jpg)
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 12
![Page 13: 11.9 Dielectric Stress in a Single-Core cable](https://reader033.fdocuments.in/reader033/viewer/2022042401/625d72e79e6851124869d5be/html5/thumbnails/13.jpg)
Assignment #:3
4/9/2017 Power System Technology / Dr. Ramzi A. Abdul-Halem 13