11 Semiconductor laser fundamentals

31
Semiconductor laser fundamentals Major disadvantages of LEDs: Too broad output beam 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.42 1.44 1.46 1.48 Energy, eV r/rmax Too broad spectrum P opt time Too slow pulse response

Transcript of 11 Semiconductor laser fundamentals

Page 1: 11 Semiconductor laser fundamentals

Semiconductor laser fundamentals

Major disadvantages of LEDs:

Too broad output beam

0

0.2

0.4

0.6

0.8

1

1.2

1.4 1.42 1.44 1.46 1.48

Energy, eV

r/rm

ax

Too broad spectrum

Popt

time

Too slow pulse response

Page 2: 11 Semiconductor laser fundamentals

Semiconductor laser fundamentals

Laser definition involves two fundamental processes:light amplification and light emission

In lasers, light amplification is achieved viastimulated emission.

Stimulated emission had been proposed by Albert Einstein in 1915but has been forgotten until 1950s

Page 3: 11 Semiconductor laser fundamentals

Absorption, Emission and Stimulated Emission

In atoms or in semiconductor crystals, absorption of a photon will occur only when the quantum energy of the photon precisely matches the energy gap between the initial and final states.

If there is no pair of energy states such that the photon energy can excite the electron from the lower to the upper state, then the matter will be transparent to that radiation.

Page 4: 11 Semiconductor laser fundamentals

Stimulated EmissionAs formulated by A. Einstein,

if an electron is already in an excited state (an upper energy level, in contrast to its lowest possible level or "ground state"), then an incoming photon can "stimulate" a

transition to that lower level, producing a second photon of the same energy.

Page 5: 11 Semiconductor laser fundamentals

Absorption – Stimulated emission competition

According to Einstein, WABS= WSE

The rate of absorption = Number of electrons in the state 1 × the probability to absorb the photon:AR = N1 WABS

The rate of Stimulated emission = Number of electrons in the state 2 × the probability to emit the photon:SER = N2 WSE

Normally, in solid states and in semiconductors, in equilibrium, N1 > N2because E1 < E2

It follows that in equilibrium or close to equilibrium,AR > SER; i.e. absorption dominates.

Page 6: 11 Semiconductor laser fundamentals

Population Inversion (PI): N2 > N1

is the key condition for the stimulated emission and the laser action

Electrons will normally reside in the lowest available energy state. They can be elevated to excited states by absorption, but no significant

collection of electrons can be accumulated by absorption alone since both spontaneous emission and stimulated emission will bring them back down.

E2, N2

E1, N1

ω ω ωω

ωRate b 12

Absorption Spontaneous Emission Stimulated Emission

Rate a 12

E2 - E 1 = ω

The total emission rate is always greater than the absorption rate.Hence, the population inversion can never be achieved by absorbing the photons(with the same energy that the one to be emitted).

Page 7: 11 Semiconductor laser fundamentals

Population Inversion (PI) in Semiconductors

Conduction band

Valence band

E

EC

EVMajority of electrons

Very few electrons

No electrons (forbidden band)

n(EC) << n(EV)

No PI

Page 8: 11 Semiconductor laser fundamentals

Electron energy distribution in semiconductors.

The probability to find an electron with the energy E:

⎟⎠⎞

⎜⎝⎛ −

+=

kTEE

EfFexp1

1)(

f(EF) = ½Example:

EC – EF = 1 eV; kT = 0.026 eV; f(EC) = 2×10-17

Under normal (quasi-equilibrium conditions) the free electron concentration must be increased by around 17 orders of magnitude to reach

the PI condition

f(E)

Ev EF Ec

1/2

Fermi Energy

Page 9: 11 Semiconductor laser fundamentals

Electron and hole concentrations requirements for population inversion in semiconductors

Ev EF Ec

1/2

The PI condition:n(EC) > n(EV)

NC fn(EC) > NV fn(EV)NC,, NV are the numbers of energy

positions available.Assume NC = NV.

Then the PI condition is:fn(EC) > fn(EV)

In the valence band, the absence of electron means the presence of the hole:fn(EV) + fp(EV) =1;fn(EV) =1 - fp(EV);

Then the PI condition is:

fn(EC) > 1 - fp(EV), or:fn(EC ) + fp(EV) > 1

fn(EC)fp(E)

fn(E)

fp(EC)

Page 10: 11 Semiconductor laser fundamentals

The Fermi energies for both electrons and holes must be positioned inside the conductance and valence bands correspondingly.

In other words, both electron and hole concentrations must be very high simultaneously

Electron and hole concentrations requirements for population inversion in semiconductors

Ev Ec

fn=1/2EFn

fp=1/2EFp

fn(EC)fp(EV)

The PI condition can be reformulated asEFn – EFp > (EC-EV)

1

1n

Fnf E

E EkT

( )exp

=−⎛ ⎞

+ ⎜ ⎟⎝ ⎠

1

1p

Fpf E

E EkT

( )exp

=−⎛ ⎞

+ ⎜ ⎟⎜ ⎟⎝ ⎠

Page 11: 11 Semiconductor laser fundamentals

Forward biased p-n junction is one way to approach the PI condition

In the first semiconductor lasers, the PI has been achieved in a heavily doped forward biased p-n junctions. The pumping current was too high to operate at

room temperature in CW-mode

P-n junction in equilibrium,n×p = ni

2; fn(EC ) + fp(EV) <1

Forward biased p-n junction,n×p >> ni

2; fn(EC ) + fp(EV) <1

Forward biased heavily doped p-n junction,n×p >> ni

2; fn(EC ) + fp(EV) >1

EF

EF

p n

EFEFnEFp

EFn

EFp

Page 12: 11 Semiconductor laser fundamentals

Zero bias

Forward bias

Zero bias

Forward bias

Quantum well heterostructure laser allows to achieving the PI at much lower pumping currents

Page 13: 11 Semiconductor laser fundamentals

Quantum well heterostructure laser

Page 14: 11 Semiconductor laser fundamentals

Laser gain

0 xI x I( ) ( ) eγ=

If the PI condition is met, the intensity of stimulated emission I(x) increasesthe the optical beam propagates along the p-n junction plane:

x=0 is the coordinate corresponding to one of the sample facets and x is the positioninside the sample along the junction plane.

γ is the laser gain

Page 15: 11 Semiconductor laser fundamentals

Laser gain and loss

0 xI x I( ) ( ) e α−=

In practical lasers, the are regions with the gain (PI) and with absorption.We can say that the gain can be positive (the actual gain) or negative (the absorption)

The net laser gain is the difference between the gain in the PI region and the absorption in the rest of the laser

Regular semiconductor material α is the absorption coefficient

0 xI x I( ) ( ) eγ=Laser γ is the gain

I(x)

I(x)

Page 16: 11 Semiconductor laser fundamentals

Self-sustainable laser emission

The stimulated emission must be initiated by the incoming photon.After all the photons have passed through the semiconductor sample the emission is over.

outputFeedback

Amplifier

Laser

Lasing can be achieved by redirecting a portion of the out coming photons back to the input

Page 17: 11 Semiconductor laser fundamentals

Cleaved facets as a Fabri-Perot etalon in heterolasers

The power reflection coefficient for the mirror is RWave amplitude reflection coefficient is R1/2

Page 18: 11 Semiconductor laser fundamentals

Waveguide structure of hetero-lasers

Page 19: 11 Semiconductor laser fundamentals

Laser Fabri-Perot resonator

Page 20: 11 Semiconductor laser fundamentals

Laser Fabri-Perot resonator –amplitude balance

Light output

Light output

P1 RP1 RP1 P1

L

The mirror power reflection factor R nn

=−+

⎛⎝⎜

⎞⎠⎟

11

2 where n is the refraction index. In GaAs, n ≈ 3.5 and R ≈ 0.31.

Optical power change after a full roundtrip is R1R2 exp(2γL)(γ is the net gain of the entire laser structure).

The condition for continuous emission is: R1R2 exp(2γL)= 1, or:

1 2

1 12

L lnR R

γ⎛ ⎞

= ⎜ ⎟⎝ ⎠

lasing condition (Fabri-Perot laser equation)

(2): R1P1

R1 R2

(1): P1

(3:) (R1P1)eγL

(4): R2 R1P1eγL

(5):R2 R1P1e2γL

1 2

1 12m ln

L R Rα

⎛ ⎞= ⎜ ⎟

⎝ ⎠is called the “mirror loss”. Then, the lasing condition: mγ α=

Page 21: 11 Semiconductor laser fundamentals

Under the equilibrium lasing condition, the electromagnetic wave phase should remain unaltered after a round trip (the path is 2L). Otherwise the wave superposition will decrease the beam intensity.

2r

n Lnλ

= nr is the semiconductor refractive index;n is any integer

Laser Fabri-Perot resonator –phase balance

Page 22: 11 Semiconductor laser fundamentals

Find the value of the integer n for operation at1.4 µm, assuming nr =3.5, L=250 µm.

Example

n ≈ 1250

Find ∆λ for the above example.

Laser mode separation:

∆λ ~ 1 nm.

Page 23: 11 Semiconductor laser fundamentals

Carrier and light intensity distribution in the transverse direction

Loss LossGain

0.5 1 1.5 20

2

1

0.5 1 1.5 20

0.5 1 1.5 20

3

2

1

6

-6

Distance (µm)

0.5 1 1.5 20

0.3

0.2

0.1

Light confinement

n-type p-type

ActiveGaAs region

Al 0.3 Ga0.7 As Al 0.3 Ga0.7 As

0.5 1 1.5 20

2

1

0.5 1 1.5 20

0.5 1 1.5 20

3

2

1

6

-6

Distance (µm)

0.5 1 1.5 20

0.3

0.2

0.1

Light confinement

n-type p-type

ActiveGaAs region

Al 0.3 Ga0.7 As Al 0.3 Ga0.7 As

Page 24: 11 Semiconductor laser fundamentals

Electrical and optical confinement in heterostructure lasers

GaAs/AlGaAs QWsGaAs/AlGaAs QWs

Page 25: 11 Semiconductor laser fundamentals

Optical gain as a function of injected carrier concentration

Loss

• The Gain must be greater or equal to the total loss in the cavity for the lasing.• The loss comes from the cavity loss outside the QW and from the leak through

the mirrors

Pumping current

Gain < Loss; no lasing

Gain > Loss; lasing

Page 26: 11 Semiconductor laser fundamentals

Laser threshold current

Loss

• d - the active layer thickness,

• L and W - the resonator length and width

• nth - the threshold electron-hole density

corresponding to Gain = Loss

• τe - the electron-hole recombination time.

th th ej q×d×n /τ=

th th eI q×L×W×d×n /τ=

Threshold current density:

Threshold current:

Page 27: 11 Semiconductor laser fundamentals

Steady-state Photon Number

The net photon population is controlled by three processes : (a) the generation by stimulated emission, (b) the absorption through various other processes, e.g., free-carrier absorption, interface scattering, inter-valence band absorption and (d) the spontaneous emission.

The laser rate equation shows the photon balance

The steady-state number of photons PhspR

NG α

=−

PhPh Ph sp

NG N N R

∂= − +

∂where Nph is the total number of photons in the cavity.

• GNph is the rate of photon generation through stimulated emission• αNph is the rate of photon decay through absorption and end-surface loss, • Rsp is the rate of spontaneous emission.

In the absence of spontaneous recombination (Rsp = 0), the lasing will not initiate: for NPh(0)=0 YdN/dt = 0

Page 28: 11 Semiconductor laser fundamentals

Output Optical Power

where αr is the loss in the resonator and αm is the mirror loss; for R1 = R2:

thint i ph

I IP E

−= ⋅ ⋅

1 1m ln

L Rα ⎛ ⎞= ⎜ ⎟

⎝ ⎠

When the laser current exceeds the threshold, all the additionally supplied e-h pairs convert their energy into stimulated emission.

Therefore, the “internal” optical power (no light is leaking through the mirrors) is:

where ηi is the internal quantum efficiency and Eph is the photon energy

A fraction of the power is coupled out through the mirrors (cleaved facets). The OUTPUT power for identical mirrors:

th mout i ph

r m

I IP E

ηα α

−= ⋅ ⋅ ⋅

+

Page 29: 11 Semiconductor laser fundamentals

The photon lifetime in lasers τp, is the time the photon spends in the resonator before being emitted or absorbed.

Typically, τp ≅ 4…10 single-path travel times (2..5 roundtrip times).Photon life time estimate:ttr1 = L / v0; L = 100 µm = 1E-4 m; v0 = 3E8/nr m/s; nr≅ 2.5Single path travel time: ttr1 = 0.75 E-12 s = 0.75 ps;tph = 4 … 10 ttr1 = 3 … 7.5 ps => very fast modulation is possible

Photon life time and laser modulation speed

Page 30: 11 Semiconductor laser fundamentals

Laser emission spectrum

Just below the threshold

Above the threshold (@ 5mW)

Page 31: 11 Semiconductor laser fundamentals

Laser –LED spectrum comparison

Above the threshold (@ 5mW)

0

0.2

0.4

0.6

0.8

1

1.2

1.4 1.42 1.44 1.46 1.48 1.5 1.52 1.54

Wavelength, um

Pow

er d

ensi

ty

1.52 um LED