RoHS Compliant

Rev. A.7, 07/31/2013 1

Features RoHS compliant

Support multi protocol from 9.9Gb/s to 11.3Gb/s

Compliant with SFP+ MSA, SFF 8431 Rev. 4.1

Compliant with SFF 8432 Rev.4.3 mechanical

dimension

Compliant with Digital diagnostic SFF-8472

Rev.11.0

Transmission distance of 80km over single mode

fiber

C-band DWDM EML laser transmitter

LC duplex connector

Hot pluggable 20 pin connector

Single power supply voltage : +3.3V

Low power dissipation

Three optional operating temperature ranges :

Option ST : 0°C to 70°C

Option ET : -5°C to 85°C

Option IT : -40°C to 85°C

Applications

SONET OC-192 / STM-64 : P16L1-2A2

10GBASE-ZR/ZW Ethernet

80km 10G FC

G.709 OUT-2

Description

OE Solutions’ Small Form Factor Pluggable

(SFP+) transceivers are compatible with the

Small Form Factor Pluggable 20pin Multi-

Source Agreement (MSA). The high performance

cooled DWDM EML transmitter and high

sensitivity APD receiver provide superior

performance for SONET/SDH and Ethernet

applications up to 80km optical links.

Enhanced Digital Diagnostics functions are

available via the 2-wire serial bus specified in the

SFF-8472 Rev. 11.0. The transmitter and receiver

features ac-coupled differential data inputs and

outputs, and an LVTTL for Tx disable input and

Tx fault output. Software TX disable is also

implemented. The receiver features differential

ac-coupled data outputs and LVTTL for LOS

(Loss of Signal) output.

10Gb/s DWDM SFP+ 80km Transceiver

RDPX0SZR-xxx

Rev. A.7, 07/31/2013 2

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

1. Absolute Maximum Ratings

Parameter Symbol Min. Typ. Max. Unit Notes

Absolute Supply Voltage Vcc_max 0 - 3.6 V -

Operating Case Temperature Top -40 - 85 °C 1,3

Operating Relative Humidity RHop 5 - 90 % 2

Storage and Transportation Temperature Tst -40 - 85 °C 2

Storage and Transportation

Relative Humidity

5 - 95 % 2

Notes: 1. Measured on top side front center of SFP module 2. Non-condensing 3.There are three options of operating maximum temperature:

Option ST: standard temperature from 0oC to 70

oC,

Option ET: extended temperature from -5oC to 85

oC

Option IT: extended temperature from -40oC to 85

oC

2. General Operating Conditions

Parameter Symbol Min. Typ. Max. Unit Notes

Bit Rate B 9.9 10.3 11.3 Gb/s -

Maximum Transmission Distance Dmax 80 - - km -

Operating Voltage Vcc 3.14 - 3.46 V -

Power Supply Current ICC - - 650 mA ST

- - 750 mA ET, IT

Total Power Consumption - - 2.1 W -

ESD (High speed pins) - - 500 V 2

Notes : 1. Supplies TEC, Current draw depends on Temperature 2. Human body model per JEDEC JESD22-A114-B, compliant with INF-8077i Rev. 4.5 August 31, 2005

Rev. A.7, 07/31/2013 3

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

3. Electrical Specifications

3.1 Transmitter Electrical Specifications (Over Operating Case Temperature and Power Supply Range)

Electrical Characteristics

Parameter Symbol Min. Typ. Max. Unit Notes

Differential Input Impedance Rin 80 100 120 Ω -

Differential Data Input Swing Vin,pp 180 - 800 mVp-p -

Data Input Rise/Fall Time tr/tf 15 - 40 ps

Tx Disable Voltage Vd 2.0 - Vcc+0.3 V 1

Tx Enable Voltage Ven 0 - 0.8 V -

Tx Fault Output Low Vtfl - - 0.4 V -

Tx Disable Assert Time T_off - - 100 s -

Tx Enable Assert Time T_on - - 2 ms -

Tx Fault Assert Time Tx_f_on - - 1 s -

Tx Fault Reset Time Tx_reset 10 - - s -

Initialization Time T_start_up_cooled - - 90 s -

Note : 1. Vcc is the voltage of host board

3.2. Receiver Electrical Specifications (Over Operating Case Temperature and Power Supply Range)

Electrical Characteristics

Parameter Symbol Min. Typ. Max. Unit Notes

Data Rate B 9.9 10.3 11.3 GBd -

Differential Output Impedance Rout 80 100 120 Ω -

Differential Data Output Swing Vout 300 - 800 mVp-p -

Data Output Rise/Fall Time tr/tf - - 45 ps -

LOS Output High Voltage Vlosh Vcc-0.5 - Vcc+0.3 V 1

LOS Output Low Voltage Vlosl 0 - 0.4 V -

LOS Assert/Deassert Time Delay T_los on/off - - 100/100 s/s -

Note : 1. Vcc is the voltage of host board

Rev. A.7, 07/31/2013 4

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

4. Optical Specifications

4.1 Transmitter Optical Specifications (Over Operating Case Temperature and Power Supply Range)

Optical Characteristics

Parameter Symbol Min. Typ. Max. Unit Notes

Laser Safety Class Class 1 according to IEC60825 -

Optical Wavelength λ 1529 - 1562 nm -

Average Optical Output Power Pout -1 - 4 dBm 1

Optical Power Overshoot Pov - - 1 dB 2

Optical power of OFF transmitter Pout-off - - -40 dBm -

Spectral Width -8 - 8 GHz 3

Optical Output Power Variation

(with respect to BOL Tc=25C,

and nominal power supply)

Pout -1 - +1 dB -

Side Mode Suppression Ratio SMSR 35 - - dB 4

Wavelength

Deviation

BOL T -50 - +50 pm 5

EOL a -100 - +100 pm

Optical Extinction Ratio(Filtered) ER 8.2 - - dB -

Optical Rise/Fall Time (20%-80%) Tr, Tf - - 35 ps -

Output Jitter - - - - 6

Notes: 1. Average power measured at output 2. Defined as Peak power – Steady-state power (in dBm) when Tx-dis is de-asserted or when the module is hot plugged with Tx_dis in low state (Tx enabled). 3. Full spectral width (RBW=0.1nm) measured 15dB down from the maximum of center wavelength peak under full modulation condition 4. Ratio of the average output power in the dominant longitudinal mode to the power in the most significant side mode peak under full modulation condition 5. Deviation related to the ITU standardized wavelength. The EOL value is met as soon as the output average power is above 10% of the steady-state power. 6. The jitter performance meets Telcodia GR-253-Core and ITU-T Recommendations G.783, G813, G825 and G82511 with ITU-T 0.172(04/2005) for the measurement methods and the measurement equipment.

Laser Safety: All transceivers in this datasheet are Class I Laser products per FDA/CDRH and IEC-60825 standards.

They must be operated under specified operating conditions.

Rev. A.7, 07/31/2013 5

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

4.2 ITU Channel and Wavelength Guide

ITU Channel Frequency

(THz)

Wavelength

(nm) ITU Channel

Frequency

(THz)

Wavelength

(nm)

39 193.9 1546.12

40 194.0 1545.32

17 191.7 1563.86 41 194.1 1544.53

18 191.8 1563.05 42 194.2 1543.73

19 191.9 1562.23 43 194.3 1542.94

20 192.0 1561.42 44 194.4 1542.14

21 192.1 1560.61 45 194.5 1541.35

22 192.2 1559.79 46 194.6 1540.56

23 192.3 1558.98 47 194.7 1539.77

24 192.4 1558.17 48 194.8 1538.98

25 192.5 1557.36 49 194.9 1538.19

26 192.6 1556.56 50 195.0 1537.40

27 192.7 1555.75 51 195.1 1536.61

28 192.8 1554.94 52 195.2 1535.82

29 192.9 1554.13 53 195.3 1535.04

30 193.0 1553.33 54 195.4 1534.25

31 193.1 1552.52 55 195.5 1533.47

32 193.2 1551.72 56 195.6 1532.68

33 193.3 1550.92 57 195.7 1531.90

34 193.4 1550.12 58 195.8 1531.12

35 193.5 1549.32 59 195.9 1530.33

36 193.6 1548.51 60 196.0 1529.55

37 193.7 1547.72

38 193.8 1546.92

Rev. A.7, 07/31/2013 6

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

4.3. Receiver Optical Specifications (Over Operating Case Temperature and Power Supply Range)

Optical Characteristics

Parameter Symbol Min. Typ. Max. Unit Notes

Optical Wavelength λ 1528 1563 nm -

Average Rx Sensitivity@10Gb/s RSENS - - -23 dBm 1, 2

Maximum Input Power Pol -6.0 - - dBm -

Receiver Reflectance - - - -27 dB -

LOS Assert LOS_A -35 - - dBm -

LOS De-assert LOS_D - - -23 dBm -

LOS Hysteresis - 0.5 - 5 dB -

Notes : 1. Measured with a PRBS of 231

-1 at 1x10-12

BER and 8.2 dB extinction ratio, 1450ps/nm

2. Guaranteed after 80km transmission over the entire operating temperature range.

Rev. A.7, 07/31/2013 7

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

5. Pin Descriptions

SFP Transceiver Electrical Pad Layout

Tx GND

TD-

TD+

Tx GND

VccT

VccR

Rx GND

RD+

RD-

Rx GND

Tx Fault

Tx Disable

SDA

RS0

Rx_LOS

RS1

Rx GND

SCL

Mod_ABS

20

19

18

17

16

15

14

13

12

11

1

2

3

4

5

6

7

8

9

10

Top of Board Bottom of Board

Tx GND

Rev. A.7, 07/31/2013 8

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

Pin Descriptions (continued)

Pin Logic Symbol Description Plug Seq. * Notes

1 - Tx GND Transmitter Ground 1 1

2 LVTTL-O Tx Fault Transmitter Fault Indication 3 2

3 LVTTL-I Tx Disable Transmitter Disable 3 3

4 LVTTL-I/O SDA 2 wire Serial Interface Data Line 3 4

5 LVTTL-I/O SCL 2 wire Serial Interface Clock 3 4

6 -

MOD_ABS Module Absent, connected to Tx GND or Rx GND in the module

3 5

7 LVTTL-I RS0 Rate Select 0, not used 3 6

8 LVTTL-O Rx LOS Receiver Loss of Signal Indication (In FC designated as Rx_LOS and in Ethernet designated as Signal Detect Bar

3 7

9 LVTTL-I RS1 Rate Select 1, not used 3 6

10 - Rx GND Receiver Ground 1 1

11 - Rx GND Receiver Ground 1 1

12 CML-O RD- Receiver Negative Data Out 3 -

13 CML-O RD+ Receiver Positive Data Out 3 -

14 - Rx GND Receiver Ground 1 1

15 - Vcc Rx Receiver Power, 3.3V±5% 2 -

16 - Vcc Tx Transmitter Power, 3.3V±5% 2 -

17 - Tx GND Transmitter Ground 1 1

18 CML-I TD+ Transmitter Positive Data In 3 -

19 CML-I TD- Transmitter Negative Data In 3 -

20 - Tx GND Transmitter Ground 1 1 *Plug Seq. : Pin engagement sequence during hot plugging Notes : 1. The module ground contacts, Tx GND abd Rx GND, shall be isolated frim the module case, that is, frame ground. 2. Tx Fault is an open collector/drain output that shall be pulled up with a 4.7k ~ 10k on the host board. Pull up voltage

between 2.0V and VccT + 0.5V. When high, output indicates a laser fault of some kind. When low, output indicates normal operation. The LD output is not turned off in case of Tx Fault

3. Tx Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the TRx with a 4.7k ~ 10k to VccT.

4. SDA and SCL should be pulled up with a 4.7k ~ 10k on the host board. The pull-up voltage shall be VccT. SCL is the clock line of 2-wire serial interface for serial ID. SDA is the data line of 2-wire serial interface for serial ID.

5. Mod_ABS is connected to Tx GND or Rx GND in the SFP+ module. The host may pull the contact up to Vcc on the host board with a resistor in the range 4.7 ~ 10k. Mod_ABS is asserted “high” when the SFP+ module is physically absent from a host slot. In the SFP MSA (INF-8074i) this contact has the same function but is called MOD_DEF0.

6. RS0 and RS1 are module input rate select contacts and are pulled low to Tx GND with a >30k resistor in the module. RS0 is an input hardware contact which optionally selects the optical receive data path rate coverage for an SFP+ module. RS1 is an input hardware contact which optionally selects the optical transmit path data rate coverage for the SFP+ module. These contacts can also be used for AS0 and AS1 if implementing SFF8079. RS1 is commonly connected to Tx GND or Rx GND in the classical SFP modules. The host needs to ensure that it will not be damaged if this contact is connected to Tx GND or Rx GND in the module. For logical definitions of RS0/RS1, see Section 2.5 of SFF-8431 Rev. 2.1.

7. LOS is an open collector output. Shall be pulled up with a 4.7k ~ 10k on host board. Pull up voltage between 2.0 and VccR+0.3. Logic 0 indicates normal operation.

Rev. A.7, 07/31/2013 9

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

5. Outline Drawings

Dimensions are in millimeters

Rev. A.7, 07/31/2013 10

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

6. PCB layout and Bezel recommendation

Dimensions are in inches (millimeters)

Notes : 1. Datum and basic dimensions established by customer.

2. Pads and vias are chassis ground, 11 locations

3. Thru holes, plating optional.

Rev. A.7, 07/31/2013 11

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

7. PCB layout and Bezel recommendation (continued)

Notes : Thru holes, plating optional.

Recommended Panel Opening

Rev. A.7, 07/31/2013 12

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

8. SFP+ Block Diagram, Power Supply Information and Host Board Interface

8.1 SFP+ Block Diagram

TOSA

TOSA

Laser

driver

Post amp.

Vcc Tx

Tx_GND

LOS

RD-

RD+

TD+

TD-

Tx Disable

Tx Fault

SCL

SDA EEPROM

10k

100

Management processor

Vcc Rx

Rx_GND

Zin diff.=

100

Zout = 50

each arm

Pin 16

Pin 3

Pin 18

Pin 19

Pin 2

Pin 1, 17, 20

Pin 5

Pin 4

Pin 15

Pin 12

Pin 13Pin 8

Pin 10, 11, 14

RS0

RS1

Pin 7

Pin 9

Mod ABS Pin 6

Rev. A.7, 07/31/2013 13

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

8.2 Recommended Host Board Supply Filtering Network

8.3 SFP+ Host Board Interface

Note 1: Host board output device circuit in the transmitter side and host board input device circuit in the receiver should be

carefully designed to meet 100ohm differential impedance matching. Also necessary is the dc bias circuit of each

input and output by taking into account of ac coupling of data input ant output of SFP+ module. For the interface of

host board devices, it is recommended to refer to the device vendor’s data sheet.

1H

1H

0.1F

0.1F

10F 10F 0.1F

Vcc +3.3V

SFP+ Module

Vcc Tx

Vcc Rx

HOST BOARD

Tx GND

Rx GND

Host Board GND

1 Tx GND

2 Tx Fault

3 Tx Disable

4 SDA

5 SCL

6 Mod ABS

7 RS0

8 Rx LOS

9 RS1

10 Rx GND

Tx GND 20

TD- 19

TD+ 18

Tx GND 17

Vcc Tx 16

Vcc Rx 15

RX GND 14

RD+ 13

RD- 12

Rx GND 11

10k

Vcc

10k

Vcc

10k

Vcc

10k

Vcc

10k

Vcc

Host board

Device

Host board

Device

Differential 100(note 1)

Differential 100(note 1)

Refer to Section 8.2

SFP+ Module

Rev. A.7, 07/31/2013 14

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

9. Digital Diagnostic Monitoring and Serial ID Operation

The information is accessed through the pin 4 (SDA), and pin 5(SCL) of the module. The device

address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is

1010001X(A2h). The EEPROM Write Protect pin is internally tied to ground with no external access,

allowing write access to the customer-writable field (bytes 128-247 of address 1010001X). Address

bytes 0-127 are not write protected and may cause diagnostic malfunctions if overwritten.

The information stored in the EEPROM, including the organization and the digital diagnostic

information, is defined in the Small Form-Factor document SFF-8472 Rev. 11.0, dated September,

2010.

9.1 Data Field Descriptions, and Serial ID Data and Map

9.2 Serial ID and Map: page A0h

Address HEX Name of Fields Description

0 03 Identifier SFP+

1 04 Ext. Identifier GBIC/SFF function is defined by serial ID only

2 07 Connector LC

3 00 Infiniband Compliance Unallocated

4 10 Reach Specifier SONET IR-1/LR-1 compliant

5 00 SONET

6 00 Gigabit Ethernet

7 00 Fiber Channel link length Unallocated

8 00 Transmitter technology Unallocated

9 01 Transmission media Single Mode (SM)

10 00 Fiber Channel Speed

Address(1010000X) (A0h) Address(1010001X) (A2h)

Serial ID Information:

Defined by SFP MSA

OE Solution Specific

Information

Reserved for SFP MSA

Alarm and Warning Limits

Reserved for External

Calibration Constants

Real Time Diagnostic

Information

OE Solutions Specific

Information

OE Solutions Specific Information

Non-volatile, customer-

writeable, field-writeable

area

0

95

127

255 255

247

119

127

95

0

55

Rev. A.7, 07/31/2013 15

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

11 06 Encoding 64B/66B

12 67 Nominal Bit Rate 10.30 Gbps

13 00

14 50 Length(9u)[km] 80 Km

15 FF

16 00 Length(50u,OM2)[m] Not support

17 00 Length(62.5u,OM1)[m] Not support

18 00 Length(copper) Not support

19 00 Length(50u,OM3)[m] Not support

20 4F

Vendor Name

O

21 45 E

22 20

23 53 S

24 4F O

25 4C L

26 55 U

27 54 T

28 49 I

29 4F O

30 4E N

31 53 S

32-35 20

36 00 Reserved

37 00

Vendor OUI

00

38 19 19

39 3A 3A

40 52

Vendor PN

R

41 44 D

42 50 P

43 58 X

44 30 0

45 53 S

46 5A Z

47 52 R

48 2D -

49 xx xx = (5Ah for ST, 45h for ET, 49h for IT)

50 xx xx=(31h:1, 32h:2,33h:3,34h:4,35h:5,36h:6)

51 xx xx=(30h:0, 31h:1, 32h:2,33h:3,34h:4,35h:5,36h:6,37h:7, 38h:8, 39h:9)

52-55 20

56 30

Vendor Rev.

0

57 31 1

58 2E .

59 Varies Varies

60

Note 1 Wavelength[nm]

61

62 Wavelength(@10pm)

63 Varies CC_BASE Checksum over 0 to 62

64 04

Option Values

Cooled Transceiver[2]

Power Level[1]

Linear Receiver Output[0]

Cooled Laser implementation

Rev. A.7, 07/31/2013 16

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

65 3A

Option Values

Rate Select[5]

Tx Disable[4]

TX Fault[3]

SD[2]

LOS[1]

Rate Select[5]

Tx Disable[4]

TX Fault[3]

LOS[1]

66 00 Bit Rate, max[%] Not Specified

67 00 Bit Rate, min[%] Not Specified

68-83 Varies Vendor S/N Varies

84-91 Varies Date Code Varies

92 68

Diagnostic Monitoring Type

Digital diagnostic[6]

Internally Cailbrated[5]

Externally Calibrated[4]

Average Power[3]

Address change req[2]

Digital diagnostic[6]

Internally Calibrated[5]

Average Power[3]

93 F0

Enhanced Options

Alarm/Warm Impl.[7]

Soft TX Dis Control[6]

Soft TX Fault monitor[5]

Soft Rx LOS monitor[4]

Soft RATE_SEL Control[3]

App Select Control[2]

Rate Select Control[1]

Alarm/Warm Impl.[7]

Soft TX Dis Control[6]

Soft TX Fault monitor[5]

Soft Rx LOS monitor[4]

94 05 SFF-8472 Compliance Rev 11.0 of SFF-8472

95 Varies CC_EXT Check Sum Byte for Bytes 64 to 94

96-127 00 Vendor Specific

128-163 Varies OES'DATA OES'DATA

164-247 00 Reserved Reserved

248-255 Varies OES'DATA OES'DATA

Note 1. 16-bit integer value in nm with byte 60 as high byte, byte 61 as low byte. The fractional part of the wavelength in

units of 0.01nm written in byte 62. Varies

9.3 Diagnostics

The enhanced digital diagnostics feature monitors five key transceiver parameters which are internally

calibrated and should be read as absolute values.

A2h address Parameter Calibration Accuracy Range

96-97 Temperature Internal +/- 3oC Note 1

98-99 Vcc Internal +/- 3% 3.13 to 3.47

100-101 Tx bias Internal +/- 10% Note 2

102-103 Tx power Internal +/- 2dB -1 to +4Bm

104-105 Rx Power Internal +/- 2dB -23 to -6dBm

Note: 1) Junction temperature of temperature sensing device. Monitoring range is from -40oC to 125

oC.

2) Specified by nominal value

Rev. A.7, 07/31/2013 17

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

9.4 Alarm Boundary Conditions

1) Transmitter Output Power and Receiver input power

Model Name Tx Low

Warning

Tx Alarm Tx High

Warning

Rx Low

Warning

Rx Alarm Rx High

Warning Low High Low High

RDPX0SZR-xxx -2.5 dBm -3 dBm 6 dBm 5.5 dBm -25 dBm -28 dBm -5 dBm -6 dBm

2) Power Supply and Transmitter Bias Current

Model Name Vcc Low

Warning

Vcc Alarm Vcc High

Warning

Bias Low

Warning

Bias Alarm Bias High

Warning Low High Low High

RDPX0SZR-xxx 3.14V 2.97 3.63V 3.47V 50mA 40mA 130mA 120mA

3) Temperature

Model Name Temp. Low Warning Temperature Alarm

Temp. High Warning Low High

RDPX0SZR-Sxx -5oC -8

oC +73

oC +70

oC

RDPX0SZR-Exx -5oC -8

oC +88

oC +85

oC

RDPX0SZR-Ixx -40oC -43

oC +88

oC +85

oC

10. Regulatory Compliance

RDPX0SZR comply with international Electromagnetic Compatibility (EMC) and international safety

requirements and standards. EMC performance is dependent on the overall system design. The RDPX0SZR is

lead-free and RoHS-compliant per Directive 2011/65/EU of the European Parliament and of the Council of 8

June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment..

11. Label

1. P/N : RDPX0SZR-xxx / 2. Bit rate , Reach , Wavelength : 10G 80km 1xxx.xxnm / 3. S/N

Rev. A.7, 07/31/2013 18

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

12. Ordering Information

Model Name OES P/C Operating Case

Temperature Nominal

Wavelength Latch Color

Application Distance

RDPX0SZR-Sxx Gxx02 0oC to 70oC

C-band

DWDM

(See Section 4.2)

White SONET/SDH

& 10G GbE 80km

RDPX0SZR-Exx Gxx10 -5oC to 85oC

C-band

DWDM

(See Section 4.2)

White SONET/SDH

& 10G GbE 80km

RDPX0SZR-Ixx Gxx08 -40oC to 85oC

C-band

DWDM

(See Section 4.2)

White SONET/SDH

& 10G GbE 80km

Notice: This data sheet is subject to change at any time without notice.

Revision History

Date Rev. # Description Author(s)

12/13/2010 A.0 Initial Release JSYU/KSP

08/30/2011 A.1 Latch Color: White

Detailed specs for Rx Sensitivity, Path penalty, ONSR w.r.t BER

JSYU

05/09/2012 A.2 Power consumption revised: 2.1W (Standard Temp) JSYU

09/15/2012 A.3 Total current changed(Max. 650mA → 545mA) JSYU

11/23/2012 A.4 Typo

(Optical Extinction Ratio (Unfiltered) → Optical Extinction

Ratio(filtered))

Datasheet correction

(SONET OC-192 LR-2 / SDH L-64.2a → SONET OC-192 / STM-64 :

P16L1-2A2)

ET, IT added

JSYU

06/26/2013 A.5 Bias High Alarm/Warning changed(120mA/110mA→130mA/120mA) JSYU

07/19/2013 Rev.A.6 Total Current changed

(ST : Max. 550mA → 650mA / ET,IT : 700mA → 750mA)

Path Penalty changed : 2dB → 2.5dB

JSYU

07/31/2013 Rev.A.7 Sensitivity and LOS De-assert changed (Max. -24dBm → Max. -23dBm)

Path Penalty deleted

Transmitter Output Power and Receiver input power changed

JSYU

Rev. A.7, 07/31/2013 19

RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications

Contact Information:

OE Solutions Co. Ltd. (Korea) Techno Park, 958-3, Daechon-Dong, Buk-Gu, Gwangju, Korea, 500-470. Tel: +82-62-602-7813, Fax: +82-62-602-7639, www.oesolution.com.

OE Solutions America, Inc. 560 Sylvan Avenue, 1

st Floor, Englewood Cliffs, NJ 07632

Tel: 201-568-1188 Fax:201-568-1177Tel: +1-201-224-2377, Fax: 1-949-272-3200