10’ x 20’ Display Booth - Front Poster Side Poster Side Poster Counter Top Secure the...

download 10’ x 20’ Display Booth - Front Poster Side Poster Side Poster Counter Top Secure the Top Braces

If you can't read please download the document

  • date post

    28-Jun-2020
  • Category

    Documents

  • view

    0
  • download

    0

Embed Size (px)

Transcript of 10’ x 20’ Display Booth - Front Poster Side Poster Side Poster Counter Top Secure the...

  • 10’ x 20’ Display Booth

    Display Setup Instructions

  • Steps to Assemble the 20ft Fusion Display:

    Step 1: Install the Carpet Padding and Vinyl Flooring. Step 2: Assemble the Backwall and Header Signs. Step 3: Install the Fluorescent Lighting and Fabric Graphic on the Center Section. Step 4: Attach the Backwall Posters and Header Posters with Velcro. Step 5: Attach the TV Monitors to the Back Posts. Step 6: Attach the Stem Lights to the top of the frame. Step 7: Assemble the Pedestals and place them along the backwall. Step 8: Assemble the Counter and place it within the booth area.

    Page 1

    10’ x 20’ Display Booth

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • Page 2

    Install the Carpet Padding and Vinyl Flooring.

    A) Unroll the Carpet Padding within the Booth Area.

    B) Install the Vinyl Flooring on top of the Carpet Padding.

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • (red)PH1035

    (blue)VS76 (orange)TR45

    (green)

    (yellow)

    PX4032 Ceiling Panel Support

    Ceiling Panel Support

    Back Post

    (Front of Booth)

    Center Section

    Side Section

    Side Section

    (Back of Booth)

    Booth Detail: Identify the Aluminum Components for the framwork.

    LEGEND

    Page 3

    94” 94”

    94”

    4”

    16” 12” 4”

    94” 91½”

    94” 94”

    94”

    94”

    15¼”

    15¼”

    15¼”

    15¼”

    76½”

    76½”

    76½”

    76½”

    76½”

    76½”

    76½”

    Angled Support Leg

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • hex key

    hex key

    Lower Beam

    Tension Lock

    Tension Lock

    Corner Post

    View showing typical assembly of components

    A) Components attach together using the Tension Locks and a hex key.

    B) Assemble the Center Section along the backwall.

    Opening

    Assemble the Backwall and Header Signs.

    Page 4

    Assemble the Center Back Panels so that the openings for the power cords are in the bottom corner as shown. Also, make sure that the Velcro faces forward to attach the �uorescent lights.

    Center Back Panel

    94”

    15¼”

    76½”

    Slide the PVC Wall Panels into place along the inside tracks of the Posts and Beams.

    Velcro on front of the Center Back Panels to attach the fluorescent lights.

    Center Section

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • C) Slide the Ceiling Panel Supports into the inside tracks along the upper beams prior to assembly.

    E) Attach the Wire Management Sections to the inside tracks at the front of the Center Section.

    D) Place the Ceiling Panel on top of the Ceiling Panel Supports.

    Opening

    Page 5

    The Wire Management snaps into place with pressure. Make sure that the Velcro faces forward.

    Ceiling Panel Support

    Ceiling Panel

    Upper Beam Center

    Back Panel 91½”94”

    94”

    94”

    15¼”

    15¼”

    15¼”

    15¼”

    76½”

    76½”

    76½”

    12” 12”

    12”

    16”

    16”

    16”

    16”

    (Velcro on front of Back Panels)

    Velcro on front of Wire Management

    Center Section

    Center Section

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • hex key

    TOP VIEW

    PR2 friction lock

    Panel Gripper

    Panel Grippers lock into position using hex key, bolt, and PR2 friction lock.

    Attach the Back Post halfway along the bottom brace at 38¼” from the Center Section as shown.

    Strongbacks attach to the Panel Grippers with the nylon threaded screws.

    Panel Gripper

    (Front of Booth)

    Center Section

    Side Section

    4”

    4” 76½”

    38¼”

    Angled Support Leg

    Nylon Set Screw

    Page 6a

    Strongback

    Strongback

    Strongback

    94”

    F) Assemble the Side Sections to the Center Section. Begin by attaching the Back Posts.

    G) Attach the Strongbacks to the back posts.

    H) The Strongbacks attach to the back posts using the Panel Grippers and Nylon Set Screws.

    Back Post Back Post

    Back Post

    Back Post

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • Side Section

    76½”

    Page 6b

    Top Brace

    I) Attach the top brace to the top of the Back Post and Center Section.

    J) Slide the Side Back Panels into place along the inside tracks.

    Side Back Panel Side

    Back Panel

    Opening for Monitor Mount

    Velcro on front of PVC Panels for Laminated Posters. (The posters may be preattached).

    Seam

    Pull back the Side Back Panels together in the middle to properly align and attach them to the Strongbacks with Velcro along the seam.

    View showing Side Back Panels attached to the Strongbacks in the back of the booth.

    Strongback

    Strongback

    Side Back Panel Side

    Back Panel Side Back Panel

    K) Attach the Side Back Panels to the Strongbacks along the seam with Velcro.

    Opening for Monitor Mount

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • Page 7

    Install the Lower Header Beam at 14½” from the top of the Post

    Lower Header Beam Header Panel

    Post

    94” 94”

    15¼”

    15¼”

    14½”

    76½”

    76½”

    M) Assemble the Header Sections.

    L) Attach the End Sections.

    N) Slide the Header Panels down into position from the top.

    (Velcro on front of Header Panel)

    Side Section Side Section

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • A) Attach the Fluorescent Lights along the center backwall panels with Velcro and attach them in series.

    B) Unfold the Fabric Graphic and attach to the frame with Velcro.

    Install the Fluorescent Lighting and Fabric Graphic along the Center Section.

    Page 8

    Fabric Graphic

    Fluorescent Light

    Fluorescent Light

    Link CableLink Cable

    Link Cable

    Power Cable Power Cable

    Velcro

    Attach the Fabric Graphic starting at the top left corner and roll downward keeping the top edge aligned with the top of the frame.

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • Page 9

    Header Poster

    A) Attach the backwall posters to the back PVC panels so that they abut together at the inside seams (if they are not already attached to the PVC panels).

    B) Attach the Header Posters to the Header Panels with Velcro.

    Attach the Laminated Backwall Posters and Laminated Header Posters with Velcro.

    Backwall Poster

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • Page 10

    Use two (2) people or more when attaching the LED Monitor to the Back Post.

    Monitor Mount attached to LED Monitor

    A) Attach the Monitor Mounts to the back of the LED Monitors with bolts.

    B) Attach the Monitor Mounts to the Back Posts with Tension Locks and hex key.

    Attach the TV Monitors to the Back Posts.

    hex key

    bolts

    Back Post

    Back Post

    Monitor Mount

    Monitor Mount

    Monitor MountLED Monitor LED Monitor

    LED Monitor

    TOP VIEW TOP VIEW

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • Attach the Stem Lights to the top of the frame.

    Secure Lights to top of frame with thumbscrews.

    View shows typical connection of lights to power source in the back of the booth.

    A) Place Lights at desired locations and secure with thumbscrews.

    B) Connect Lights to power source.

    Page 11

    Stem Light

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • LEGEND

    Back Panel Assembly

    Back Panel Assembly

    Front Panel Assembly

    Front Panel Assembly

    Counter

    Pedestal

    Counter Components

    Pedestal Components

    Side Panel

    Side Panel

    Side Panel

    Counter Top

    Side Panel

    Middle Shelf

    Middle Shelf

    Page 12

    Assemble the Counter and Pedestals.

    A) Counter Components are marked with a blue dot ( ) and the Pedestal Compontents are marked with a pink dot ( ).

    Pedestal Top

    (There are two (2) Pedestals included with this Display Booth)

    F-20-6-1_Ovation

    20ft Fusion Trade Show Display BoothAssembly Instructions:

  • Step 1: Attach the Bottom Braces to the Front and Back Panel Assemblies with the Tension Locks and hex key.

    Step 2: Slide one of the Side Panels into the frame.

    Back Panel Assembly

    Back Panel Assembly

    Front Panel Assembly

    Front Panel A