1.09 Item Wise Detailed Description.xls
-
Upload
rajesh-chowhan -
Category
Documents
-
view
62 -
download
9
description
Transcript of 1.09 Item Wise Detailed Description.xls
NOTE:
i)
ii)
iii)
iv) Basic rates wherever mentioned are exclusive of taxes.
v)
vi)
vii)
viii)
ix) The manufacturer test certificate has to be submitted for the following items
required etc.
List of Tests:- (No. of Samples as per IS Code)
b) Exterior Grade MDF Board
d) Gypsum Board / Calcium Silicate Board / Hunter Douglas Panels
e) Electrical Light Fitting and Wiring
x) Marine Plywood specified shall be confirm to BIS - 710 - 1976 & should bear ISI mark
xi) Commercial Plywood specified shall be confirm to BIS - 303 & should bear ISI mark
xii) Flush door shutter specified shall be confirm to IS-2202-1999
xiii)
xiv) For all Civil Items Premix materials of approved make shall be used. Viz.Plaster, Mortor etc.
Unit abbreviation: Please read the units in the following table as below
1 LS - Lump Sum
2 SM - Square Metre
3 EA - Each
4 KG - Kilogram
5 MR - Running Metre
Annexure - X
All "MDF" boards & frames shall be exterior grade unless clearly specified & confirming to IS 12406 : 2003.
Sizes of wooden sections specified in the items stated under are with permissible tolerance and Best quality Teak wood / BTC approved by
the architect.
All items mentioned in the BOQ are for providing , supplying and fixing unless otherwise clearly specified.
All brass / stainless steel fittings / fixtures shall be shall be approved before use in the works.
c) Vitrified & Ceramic Tiles
a) Plywood
All shutters with locking arrangements to be provided with brass shoe for key holes and Magnetic ball catches, and tower bolts.
The quantities mentioned in the BOQ are approximate and may vary or can be omitted without assigning any reasons..
If the relevant manufacturer test certificates are not arranged by the vendor, than the test has to be carried out by vendor as per the
direction by HPCL, as per the relevant IS code at Vendor's cost
All the materials required for execution of work & company brands which is used in site must be get approved from Architects / HPCL
before they are brought to site & also before actually put to use.
All drawers to be provided with drawer channels of approved make.
Page 76 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
CIVIL WORKS
1 Buyback-Misc.Various items LS 1
HPCL proposes to dispose-off the existing materials and interiors at 2nd Floor (as per annexure) on “As is
where is basis”, accordingly the successful vendor has to offer their rates. Scopes of job includes
dismantling and taking away / clear the debris before commencing the job.
2 Breaking brickwall SM 260
Demolition / dismantling existing brick walls complete as per site direction.The item include
transportation,loading and unloading of the material in a place and dumping at BMC approved dumping
ground / as directed by Engineer in-charge.Plan area of floor shall be measured for the payment.The
contractor will have to put up a proper and sufficient hoarding, screen and fence during the time as may be
necessary for the safety and convenience of the inmates of the existing buildings and maintain the same in
the good condition during demolition and where necessary cause such hoarding or fence to be well lighted
during the night to prevent accidents.Contractor will have to make good without any extra payment any
damage done during construction.
BRICK WORK and PLASTERING
3 Brick masonry-115 mm THK SM 20
Providing and constructing 115mm thk. brick wall with locally available best quality bricks, laid to perfect
line, level and plumb in Cement Mortar 1:4 in half brick thick wall.Openings to be left for doors and
windows including R.C.C stiffners 150 x 150 mm with mild steel longitudinal reinforcement of 2 Nos. 10 mm
Dia. longitudinal bars at top and bottom and 6 mm ties at 200 mm C/C in 1:2:4 @ every 1.2 mt.
level.Openings to be left for doors and windows.Cost to include lintels above doors etc. including
scaffoldings, racking cut joints and weathering complete.
4 Brick masonry-230 mm THK SM 5
Same as above ' item no. 3 ' but Providing and constructing 230 mm thk Brick Masonary with locally
available best quality bricks in cement mortar 1:4 in superstructures as backing in composite masonary
including scaffolding, racking out joints and weathering complete.
5 Internal Plaster - 12 mm THK SM 50
Providing and Applying 12mm thk single coat cement plaster to all masonary and concrete surfaces with
cement mortar (1:4) in proper line, level, plumb inclusive of curing and finishing the same with "Birla" white
putty as directed by the architect.Rate to include hacking, scaffolding, curing, complete in all position etc
wherever necessary.
STRUCTURAL REPAIRS
Whereever necessary and as directed by Architect
Erecting, sturding, scaffolding, dismantling the entire loose cover concrete,exposing the corroded
reinforcement steel,cleaning and removing the corrosion using rusticide cleaning chemical.The spoiled
concrete surface shall be thoroughly cleaned and repair area shall be demarcated and cut to a depth of
10mm using a machine cutter.If the corroded reinforcement has lost its diameter substantially,then new
steel reinforcement mesh has to fixed.The steel so fixed or cleaned shall be applied with Nito Zinc primer
of M/s fosroc / approved equivalant with in two hours,the entire area shall be primed with Nito band HAR
of M/s Forsorc / approved equivalant and Rendoroc-,polymer mortar shall be hand packed to suitale depth
so as to obtain a well compacted cover concrete. All he chmicals shall be used strictly as per manufacturers
specifications. The payment shall be made in kilograms of each chemical used in the repair as mentioned
below.
6 Structural rep. with-Rusticide KG 10
Structural repair with-Rusticide
7 Structural rep. with-NitoZinc KG 10
Structural repair with-NitoZinc
8 Strl rep with-Nitiband HAR KG 20
Structural repair with-Nitiband HAR
9 Strl rep with-Rendoro HB2 KG 20
Structural repair with-Rendoro HB2
ITEM DESCRIPTION FOR INTERIORS / RENOVATION FOR 2nd FLOOR R & C BUILDING, BYCULLA
Page 77 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
10 WATER PROOFING FOR WALL SM 200
Cement based water proofing: Applying cement based water proofing using PIDELITE/ROFF cement based
polymer water proofing compound and applying the same as per manufacturer specification and will be in
following steps (i) Chipping of the wall plaster till the exposure of brick, (ii) filling the gaps, crevices, etc
with cement mortar mixed with water proofing compound, (iii) Providing the 12 mm thick plaster mixed
with water proofing compound and (iv) painting the final wall surface.
11 WATER PROOFING -TOILETS/PANTRY SM 20
( Note : All rates in this sub-head are inclusive of all lead and Lofts for all floors, unless otherwise
specified ) ( All items in this trade to be executed by specilised and approved agency only )
The work shall be executed through the specialised approved agency with 2yrs guarantee, quoted rates
shall include the costs of all materials, labour, waterproof specialised chemical, T and P with contractor's
profits all specialised waterproofing chemical shall be used as per specification mentioned below :-
Providing and laying polymer based waterproofing treatments to the sunken portion of toilets, WC, bidets
etc. all as per specification mentioned below :-
Preparation of concrete surface by removing loose particle including chippings of the skin of RCC top slab if
required and cleaning the surface including cutting of 'V' grooves at corners and joints and fillings the 'V'
grooves with PMC mortar after cleaning and applying a coat of honey like cement slurry added with
waterproofing compound of approved makes on cleaned concrete, bricks or guinted surface as per
manufacures specification including preparation of above surface by applying waterproof cement mortar in
1:4 in 15mm thickness over the exposed rough concrete, bricks or guinted surface ( the 'V' grooves shall be
treated with polymers modified cementetious coating prior to applying PMC mortar ).
After laying of all soil pipes, floor traps is completed the floor of the Toilets & pantry portion shall be
covered with waterproofing base coat finished in neat cement slurry & over that Brickbat coba embedded
manually with 15-20 mm wide joints in 20 mm thk Waterproofing mortar 1:4 in layers upto the required Cill
level height, having top layers of 25mm thk waterproof mortar 1:4 & water proofing treatment on RCC roof
surface etc.
Providing and laying water proofing in toilet & pantry water proofing treatment on RCC roof surface etc, by
applying Polymer modified cementous slurry mixed with Armourcerete of M/s The Structural Water
Proofing Company Pvt. Ltd., or Tapecrere of M/s Cico Engineer Service or Hydro Proof of Fosroc consisting
of following layers : (i) first layer of slurry of cement @ 0.488 Kg./sqm mixed with Armourcrete or
Tapecrete @ 0.253 Kg/sqm. This layer will be allowed to air cure for 4 hours. (ii) Second layer of slurry of
cement @ 0.242 Kg./sqm mixed with Armourcrete or Tapecrete @ 0.126 Kg./Sam. This layer will be
allowed to air cure for 4 hours followed by water curing for 48 hours.The rates includes preparation of
surface treatment & sealing of all joints corners, junction with polymer mixed slurry. etc. complete in all
respect, as per the specifications, drawing & as directed by Architect / Engineer incharge.This treatment to
continue to the toilet walls upto 900mm height.Curing / testing by stagnating water for a period not less
than 72 hrs. etc. complete.
Measurement of waterproofing shall be taken only for floor area.
FLOORING AND DADO
FLOORING
NOTE for flooring and Dado Work :
All granite and marble flooring / dado sizes will be as per the site dimensions.
Actually executed quantity will be measured and no consideration shall be given for wastage and
difference of method of measurement between market / supplier's method and site method.
The rate shall include laying vitrified tiles / marble / granite / ceramic tiles / stone slabs to any pattern as
specified and shown on drawings and no extra cost shall be paid for wastage of materials.
The rate shall also include cost of cutting tiles for fixing electrical boxes and switches, water-taps, nahani
traps, plumbing accessories etc. for which no extra payment shall be made.
Page 78 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
12 Vitrified mirror finished tile SM 650
Providing and laying Vitrified mirror finished tiles of approved sizes, colour and makes on flooring as per
approved pattern indicated in the Architectural drawing.Tiles to be laid to proper line, level and joints
finished in cement slurry with required thickness of Premix cement mortor bedding and the tiles grooves
to be filled with white cement mix with tiles matching colour including curing etc.No extra is payable for
additional thickness of cement bedding to match adjoining floors wherever required as per drawing and
direction.The edges of the tiles should be straight and without bends & tiles shall be free of any variation in
colour or texture.Cost shall include curing,cleaning and acid washing etc complete. Basic Rate of mirror
polished vitrified tiles: Rs. 1300/- per SMT.
13 Finished granite slab 17-19 mm SM 10
Providing and fixing any types of finished granite slabs of 17 to 19 mm thk machine cut, machine polished
in nominal sizes, as per drawing and pattern.Slabs to be laid to proper line, level and joints of granite
finished in white cement slurry with required thickness of Premix cement mortor bedding and granite
grooves to be filled with white cement mix with granite matching colour etc.including curing complete as
per specification.Rate to include cost of design patterns in combination of two or three different colour as
per dwgs. Complete including Polishing of edges curing etc. no extra payable towards wastage.Rate to be
applicable for all levels and heights.Slabs shall be free of any variation in colour or texture.Cost to include
curing,cleaning and acid washing etc complete.No extra is payable for additional thickness of bedding to
match adjoining the floor as per direction.Basic cost of granite upto Rs. 1600/- per sq.mt.
14 Laminated wooden flrg 8-10mm SM 65
Providing and Fixing in position laminated wooden flooring of approved equivalent makes of 8-10mm thick
including sound block having a wear resistance level of AC-5 series as per EN 13329 with direct lamination
on top of special developed substrata with plank density of 850 kg/m3.Plank of approved sizes having
ProLoc triple locking system click joints and providing skirting board,beading to match the flooring in
specified areas as per approval etc. complete in all respects as per the drawing and directions.The item
shall also include door profiles wherever required.Basic rate Rs.3000/- Per Smt.
15 Italian marble Slab-flrg&dado SM 75
Providing and fixing Italian marble for flooring and dado of uniform colour with 15mm thick +2mm
tolerance as per drawing and pattern including required thickness of Premix cement mortor bedding close
jointed and floated with white cement slurry including grooves to be filled with white cement mix with
matching colour laid to level as required, curing complete including inlay in brass / glass / wooden patties
as per specification.Rate applicable for all levels and heights.Slabs shall be free of any variation in colour or
texture etc complete.Cost to include shall curing,cleaning and washing etc complete.No extra is payable for
additional thickness of bedding to match adjoining floors, as per directions of Engineer – in – charge.The
item includes complete finishing of the flooring with tin oxide Mirror polish.Basic Rate Rs. 3500/- Per SMT.
Page 79 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
16 Ceramic Mosaic tile flooring SM 40
Providing and fixing Ceramic Mosaics tiles of Nitco makes or Approved equivalent makes for border at
passage of 4mm thk and sizes 1" x 1" in walls, dado, pillars, flooring inlay etc., laid on a bed of Premix
cement mortor bedding and neat cement slurry, in perfect line, plain and plumb, joints finished with flush
pointing in the white cement mixed with pigment to match the shade of tile complete as per the
specifications and drawings and as directed by Architect / Engineer incharge.Basic cost of tiles Rs.3000/-
per Smt.
17 Crys Glass Mos/SS Mos./Bissaza SM 20
Providing and fixing Crystal Glass Mosaic / SS Mosaic / Bissaza tiles of ( Polladio / La Mosaico / Bisazza /
Little glass makes ) 4mm thk and sizes 1" x 1" in walls, dado, pillars, Columns, flooring inlay etc., laid on a
bed of Premix cement mortor bedding and neat cement slurry, in perfect line, plain and plumb, joints
finished with flush pointing in the white cement mixed with pigment to match the shade of tile complete
as per the specifications and drawings and as directed by Architect / Engineer incharge.Basic cost of tiles
Rs.3000/- per Smt.
18 Floor Guard protector sheet SM 900
Providing and laying floor guard protector sheet in roll form above newly laid flooring on polythene plastic
protective cover on flooring and removing when directed etc. complete as per details.
SKIRTING
19 Skirting from vitrified tile MR 35
Providing and fixing skirting 75 mm high from first quality vitrified, mirror polished matching to floor finish
factory cut readymade tiles of approved colour, thickness and make in the office area as indicated in the
Architectural drawings to perfect line and level in Premix cement mortor bedding. Care to be taken to
confirm joints in the walls to joints on floor.Rate inclusive of any chipping of wall-plaster as may be
required.Basic Rate of mirror polished vitrified tiles Rs. 1300/- Per Smt.The skirting to be flushed with wall
finish including providing 6mm x 6mm groove above the skirting top.
Page 80 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
20 Skirting by gran. slab17-19mm MR 15
Providing and fixing skirting 75 mm high with the details as item no. '19 ' granite slab of 17 to 19mm
thick.of approved quality.Basic Rate of Granite 1600/- Per Smt
PANTRY COUNTER
21 Pantry counter SM 2
Providing & fixing in position pantry counter as per the drawing machine cut, machine polished of
approved colour granite slab of 17 to 19mm thk Over built up with cudappah slabs at top & verticals of
38mm thick with a Premix cement morar bedding with M.S. Supporting brackets etc. laid in perfect line and
level / slope as desired including Curing, polishing and cleaning up with all joints filled and floated in
matching cement mortar.
All exposed surfaces whether external or internal including all edges shall be machine polished.Rate to
include all holes and openings required for plumbing fixtures and fittings.Facia & Skirting to be provided as
per drawing with all edges and face polished and fixed to cuddapah platform with brass dowels 12mm
diameter fixed to cement mortar.(Rate to include all materials given in the item above) Basic rate of granite
Rs 1600/- Per Smt. (Only plan area will be measured wastage due to dimensional difference, pattern etc.,
will be to the contractor's account)
SANITARY FITTING
22 S S sink-510X510 mm EA 1
Supplying and fixing in position of stainless steel sink big of sizes 510 x 510mm of approved design, shades,
colour etc. complete as per approved by Architect / EIC.
DRAINAGE WORK
G.I. Pipes - concealed
Providing, laying, fixing and testing in position 'C' Class tested Galvinized iron pipes of approved equivalent
makes with all fitting like tees, bends, elbows, reducers, unions, nipples etc including concealing the pipes
in walls or under floors,including making chases in the walls, wrapping the pipes with hessian cloth soaked
in bitumen, fixing in the wall with M.S clamps including 3 coats of bitumen paints / etc complete hydraulic
testing after laying the pipes as specified including making holes in walls or floors as required and making
good the same with brass fitting of seamless half hard temper, with cylindrical and smooth inner and outer
surface, and free from air holes cracks and other defects.All G.I Pipes and fittings should be properly
cleaned before joining. All the joints shall be perfectly air and water tight. If require all pipework shall be
supported with PVC / G.I clips. and complete as directed including covering with PVC adhesive tape.
23 'C' Class G.I. Pipe-15 mm dia. MR 10
24 'C' Class G.I. Pipe-20 mm dia. MR 5
25 'C' Class G.I. Pipe-25 mm dia. MR 5
26 'C' Class G.I. Pipe-32 mm dia. MR 5
C.I. Pipes
Providing, laying and jointing in position C.I heavy quality pipes of approved equivalent makes by Architect
including C.I. spigot and socket pipes for soil, waste and vent, conforming to IS 1729 - 1964 including all
fittings like offsets, bends cowls, single or centri pipes conforming to I.S. double junctions of different
degrees, with or without access doors etc. including caulking spun yarn soaked in tar and jointing with
cement mortar 1:2 / lead fixing them on floors or vertically against walls by specially made M.S. brackets or
clamps so as to keep the pipes away from the wall including all scaffolding, water testing after laying the
pipes as specified and painting etc complete.
27 C.I heavy qualy pipe-100mm dia MR 5
28 C.I heavy qualy pipe-75 mm dia MR 5
29 C.I heavy qualy pipe-50 mm dia MR 5
C.I. special fittings
Providing & fixing in position C.I. special fittings of approved equivalent makes such as bends, tees, wyes,
etc. with or without access as directed such as tees,bends,off-sets with lead caulked joints, complete in all
respects as per directions.
30 C.I.special fittings-100mm dia EA 2
31 C.I.special fittings-75 mm dia EA 2
32 C.I.special fittings-50 mm dia EA 2
Page 81 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Floor Traps
33 C.I. Floor-traps EA 2
Providing and fixing C.I. Floor-traps of approved equivalent makes of self-cleansing design with stainless
steel grating including cutting and making good the same for floors and walls wherever necessary,
complete in all respects as per directions.
Stop-Cock
34 C.P.Brass concealed stop-cock EA 2
Providing and fixing in position 15mm dia. Chrome Plated brass concealed stop-cock with adjustable wall
flange of approved equivalent makes.
Gate Valves
35 Gun metal gate valve-50mm NB EA 2
Providing and fixing heavy quality gun metal gate valves of approved equivalent makes tested upto 300 lbs /
sq. local 20 kg / sq.cm of approved quality.
(leader or GG make) I.S.778-1971 of size 50 mm NB.
36 Bottle trap - 32mm dia. EA 2
Providing and fixing in position in position bottle trap of approved equivalent makes of economy model
32mm dia. with 190mm and 125mm long wall connection pipes with wall flanges including with waste
coupling 32mm dia. size full threaded and necessary C.P. brass connection pipes and nuts with rubber
adopter for waste connection complete including filling gap between counter and wash basin with
approved type poly sulphide sealant, cutting and making good the walls wherever required etc.
37 CP Tap sink mixer EA 2
Providing and fixing in position heavy tested ISI marked screw down chrome plated clinical lever range pillar
tap sink mixer with regular extended spout wall mounted model of approved equivalent makes.
PARTITION
Note : All partitions are to be fixed with Screws to ceiling & floor. All joints of frame & panels to be fixed
with full threaded screws.
38 Ext grade MDF frame-35X50mm SM 1100
Providing and Fixing Exterior grade MDF frame out of 35 X 50mm mm thk. of approved makes for any
shapes of the partitions for full height, Low height, boxing, soffits @ average 400 mm c/c vertical member
and 400 mm c/c horizontal member including necessary support, bracing member both ways securely fixed
to ceiling / floor with proper lap / scarf joints complete with Screws and full threaded screws for joining
members and required hardware and as per details and instructions.
39 Ext grade MDF frame-25X50mm SM 220
Providing and Fixing Exterior grade MDF frame out of 25mm thk. X 50mm of approved makes for paneling
of walls / columns wide @ average 400 mm c/c. vertical member and 400 mm c/c horizontal member
including necessary support,bracing member both ways securely fixed to ceiling / floor with proper lap /
scarf joints complete with screws, full threaded screws with required hardware and as per details and
instructions.
40 PANEL:Ext grade MDF 12mm thk SM 2050
Providing and Fixing 12mm thk Exterior grade MDF board of approved equivalent makes, fixed to the frame
with full threaded screws and adhesive providing grooves / curved / any shapes and sizes etc fixing the
same for receiving finish the same as per design, details and instructions.Actual executed area will be
measured and no wastage will be paid for the same etc. complete.
PANEL: Marine ply IS 710
Providing and fixing marine ply IS 710 of approved equivalent makes, fixed to the frame with full threaded
screws and adhesive finishing the same as per design, details and instructions.Actual executed area will be
measured and no wastage will be paid for the same etc. complete.
41 PANELS: 19mm thk. SM 240
42 PANELS: 12mm thk. SM 110
43 PANELS : 6 mm thk. SM 110
44 PANELS:4mm thk ply-any shape SM 55
PANELS : 4mm thk ply for any type of curved / round / angular / any type shapes as per design, detail and
instruction.
Page 82 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
PANEL:Toughened clear glass
Providing and fixing in position toughened clear glass panel in partition as shown in detail drawing and as
per instructions including necessary wooden beadings etc finished in 3 coats of melamine polish of
approved shade and makes.Item to be completed in all respects as per drawings and
instructions.Additional supports required for the glazed portion shall be included in the item itself and no
extra will be paid for the same.All exposed edges of the glass shall be crystal machine polished.
45 PANELS : 10 mm thk. SM 65
46 PANELS : 6 mm thk. SM 35
47 PANELS:Toughened curved glass SM 35
PANELS : Same as item nos. 44 but 10 mm thk. Clear toughened Curved / bent glass as per design drawing,
detail and instruction.
48 PANEL: 3M-FORM of 6mm thk SM 30
Providing and fixing approved design panels of 6mm thk. Eco-resin of 3M-form of hunter douglas or
approved by Architect with necessary teakwood beading and moulding as per any shapes shown in the
drawing and direction.Basic rate of 3M-Form :- 10000/- Per Smt.
49 Glass in S.S. 'D' Bracket EA 150
Providing and Fixing of Glass Of any thickness in stainless steel "D" Brackets Approved make only.
50 Mirror panelling at wall -3mm SM 10
Providing and fixing in position 3mm thk. Mirror at wall or partition with 6mm thk back ply of approved size
& makes of ( Asahi / Saint Gobain / Modiguard ) fixed at wall or partition with stainless steel studs / screws
/ button complete as shown in architects drawing.
51 DESIGN ON GLASS WITH 3M FILM SM 80
DESIGN WITH 3M FILM: Providing & fixing Etching type design on glass with 3M film as per design &
etching paper upto 75% covering of the glass area.Basic Rate of Etching paper 1500 Rs. Per Smt.
52 ETCHING/FROSTING TYPE DESIGN SM 30
ETCHING TYPE DESIGN : Providing & fixing Etching / frosting / acid etching / granular blasting and all type of
processing in combination of the above or in isolation of any kind in the glass all complete as per
design.Single linear measurement ( L X B ) will be made for one piece of glass for the combination of the
treatment.Basic Rate 3000 Rs. Per Smt.
CLADDING ON PANELS
53 Decorative laminate 1.0 mm thk SM 1100
CLADDING ON PANELS : (CL1) Providing and fixing 1.0 mm thick decorative laminate of approved
makes.Actual executed area will be measured as two sides of same partition are likely to have different
finishes.Rate of this item shall include cost of any cross matching laminate in approved pattern skirting, etc.
as per details.The finishing material shall be fixed in required divisions / panels / pattern with proper
grooves etc. as per drawings and directions as per details and with necessary hardware, adhesive etc. Basic
Rate. 450/- Smt.
54 Wall covering / wallpaper SM 110
CLADDING ON PANELS : Providing and Fixing wall covering or wallpaper of any types of finishes of approved
makes in required texture, pattern and shade to the panels with necessary adhesive and beading etc. Basic
Rate : approx. Rs. 2500/- Per Smt.
55 Metal finished laminate 0.8mm SM 15
CLADDING ON PANELS : (CL1) Specification Same as above item no. 53 but Providing and Fixing 0.8 mm
Metal finished laminate of approved equivalent makes.Basic Rate of Metal Laminate 2500 /- Per Smt.
Page 83 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
56 Veneer 3-4 mm thk SM 1000
CLADDING ON PANELS : (CL2) Providing and Fixing 3 to 4mm thk. veneer of approved equivalent makes
fixed to panels in any pattern and design with cross matching veneer in required texture & grooves etc.
with teakwood moulding & necessary hardware & adhesive.Veneer should be finished in 3 coats of
melamine polish of approved shade.Basic Rate of veneer Rs.1100/- Per Smt.
57 VeneerReconstituted burl/dyed SM 375
CLADDING ON PANELS : (CL2) Specification Same as item no. 56 above but with re-constituted burl / dyed /
normal veneer of Approved makes or Approved equivalent Basic Rate Rs.2400/- per smt.
GLASS BRICK WALL / PARTITION :
Providing & Fixing Glass brick partition from "SOLARIS" make of Germany or approved equivalent of same
standard of size with approved design, joints in white cement mortar & plastic spacers if req. fixed in
wooden partition as per instructions, design and details.
58 GLASS BKWALL/PART:190X190X80mm SM 10
59 Coloured glass block SM 5
Specification Same as above item no. 58 but coloured glass block of poesia makes and design or Approved
equivalent.
MOULDING ON PANELS
MOULDING ON PANELS: (CL1) Providing & Fixing Teak Wood moulding as per required profile fixed to the
panel with joinery as per details with necessary hardware, adhesive & finished in 3 coats of melamine
polish of approved shade.This item will operate only for those mouldings which are to be fixed
independent of any other item as mentioned in the bill of Quantities and not measured under any other
item.
60 MOULDING ON PANELS:40 X 75mm MR 110
61 MOULDING ON PANELS:19 X 75 mm MR 385
62 MOULDING ON PANELS:25mm X 25mm MR 45
63 MOULDING ON PANELS: 12 X 12mm MR 90
64 MOULDING ON PANELS:38 X 150mm MR 55
65 CLADDING ON PANEL:Soft board SM 65
CLADDING ON PANELS: Providing and fixing 12mm thick soft board covered with fabric of approved make
and shade of premium quality and Basic cost of fabric upto Rs. 750/- per RM.The board shall have
teakwood / cedar / beech / matching wooden beading, lipping all-round.The board shall be fixed on
prepared surface with necessary hardware fittings etc. complete.Rate quoted shall be for the complete
finished work including all the materials and labour mentioned above.
66 White mattfinish writing board SM 25
Providing and fixing white board in matt finish of approved equivalent makes of writing board with
enameled sheet steel front, GI back over approved inner core, of specified size black or chocolate colour
anodized aluminum beading to form the screen including the necessary accessories such as magnetic
symbols, magnetic letters, magnetic strips, magnetic eraser, magnetic dry marker 4 Nos., spare felt for
eraser, board fixing clips etc. and the board shall be made out of enamelled sheet with backing of AC sheet
to suitable thickness etc. complete and all as per manufacturer's specification and as directed.Rate shall be
inclusive of making and fixing wooden ledge for full length of the board for keeping marker pen, eraser etc.
Rate quoted shall be for the complete finished work including ledge board to keep accessories, and all
materials and labour mentioned above.
PELMETS :
67 Pelmet:19mm thk marine plywood MR 10
Providing and fixing in position pelmet out of 19mm thk marine plywood finished with approved veneer
with melamine polish from the front portion and synthetic enamel paints from inside.Size of the the
pelmet -150 x 175 mm.Item to be completed in all respects as per drawings & instruction from E.I.C.Basic
rate of veneer 1100/- per Smt.
Page 84 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
68 PHENOTHERM INSUL.BAKELITEHYLEM SM 10
Providing & Fixing in position 50mm thk. Phenotherm insulation (KP/AL) in partitions wherever as shown
and as per the site directions. The rate shall include covering of aluminum foils as per manufacturers’
specifications.
Mode of measurement – The measurement shall be given as the elevational area of the partition.
FIBREGLASSWL INSULATION IN PARTITION
Supply & installation fiber glass wool insulation in partition with factory faced aluminium sheet (Density not
less 32kg/m³) on G.P. sheet deck as per specifications.Glass wool make: U.P Twiga / Kimco / Owens
Corning.
69 FIBREGLASSWOOL IN PART.-25MM SM 5
70 FIBREGLASSWOOL IN PART.-50MM SM 15
71 ACRY. SHEET PANELLING-6MM SM 10
Providing and fixing in position 6mm thk. approved coloured Acrylic sheet panelling at wall or ceiling boxing
with stainless steel studs complete as shown in architects drawing.
72 FROST.FILM LAM GLASS PART-12MM SM 20
Providing and fixing 12mm thk frosted film Laminated sandwitch glass partition of Adaro makes or
approved by Architect with necessary beading etc finished with 3 coats of melamine polished.Item to be
completed in all respects as per drawings & instructions.Additional supports required for the glazed
portion shall be included in the item itself and no extra will be paid for the same as per architectural design,
drawing & instruction etc complete.
73 ANTITERMITE TREATMT/PEST CTRL SM 1000
Providing and executing preconstruction with antitermite treatment or pest control treatment to the
entire office as per manufacture's specification of approved makes of PCI / PECOPP.
DOORS
74 DOOR FRAME:50X75mm in TeakWood MR 15
DOOR FRAMES: Providing and Fixing 50mm x 75mm in Teak Wood with rebate to receive shutter, fixed to
the partitions as per details and finished in 3 coats of melamine polish of approved shade and as per
instructions.Measurement of frame shall taken along the centre line of frame.
75 DOOR JAMBS:In granite 17-19mm MR 2
DOORS JAMBS : Providing and erecting door jambs in stepped detail, approved color granite of 17 to 19mm
thick.Granite jambs to be fixed in perfect line, level and plumb on cement bedding in CM 1:3 as indicated in
the Architectural drawings.Granite jambs to have 12mm projecting out from the wall on both the sides
having full round polished moulded nosing on the entire running length on both the granite pattis on both
sides. Approx. Basic cost of granite upto Rs. 1600/- per Sq.mt.
76 FLUSH DOOR:Factory mfg 35mm tk SM 65
FLUSH DOORS: Providing and fixing in position 35mm thk flush door shutters of approved make as per
details.Door to be finished as per detail and finishes which shall be paid seperately in respective items and
with necessary T.W beading & moulding to be finished with melamine polish.Including all hardware of
approved makes etc.
77 GLASS ENTRANCE DOOR-12MM THK SM 12
GLASS ENTRANCE DOOR: Providing and Fixing in position main glass door with 12mm thk. Tinted
toughened clear glass portion with an stainless steel patch fittings at top & bottom member with corner
glass door lock including handle with other side connector of approved equivalent makes as per drawing
with necessary glass fitting & floor spring of approved make rate to include decorative approved stainless
steel handled, decoratives approved lock complete in all respect as per direction.
78 Shutter:Pantryplatform37x 50mm SM 3
Providing & fixing of shutters for pantry platform out of 25mm x 50mm TW frame all around with 19mm
thick marine plywood shutters cladded exposed side with 1.0mm thick laminate of approved make and
colour.Shelves to be made out of 19mm thk marine ply with TW lipping on TW battens at the wall side. All
internal portion to be finished in 3 coats of synthetic enamel paint over 1 coat of primer. All internal &
external TW portion to be finished in 3 coats melamine polish. All complete including magnetic catches,
hinges, towerbolts, locks & handles in brass of approved make & quality.
79 TRAP DOOR SHUTTER-12MM MARINE SM 6
Providing and fixing in position openable trap door shutter for access in false ceiling in 12mm thk marine
ply finished with approved shade enamel paint on both sides, with brass concealed hinges on teakwood
framework of 50 x 50mm.All exposed edges shall be finished with 6mm thk teakwood lipping.The
framework shall be secured to the ceiling with proper vertical M.S section.All exposed & internal surface
shall be finished with enamel paint matching the ceiling colour.Brass hinges "L" end key trap door lock etc.
shall form part of standard fitting & fixtures as per drawing & direction.
FITTINGS and FIXTURES:
80 HINGE:100x75x3mm brassoxidised EA 10
HINGES: Providing and Fixing brass oxidised "Butt" hinges of heavy duty ball bearing hinges of approved
equivalent makes made with S.S centre pin, wt. 3.9 Kg./ doz. fixed to frame with brass screws with all
accessories complete.
81 DEAD LOCK WITH S.S KNOB EA 29
Page 85 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
DEAD LOCK : Providing and Fixing Dead lock with standard lock case for europrofile cylinder of approved
equivalent makes with chrome plated plate complete with all accessories.
82 FLOOR SPRING TO CABIN DOORS EA 27
Page 86 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
FLOOR SPRING TO CABIN DOORS : Providing and Fixing double action hydraulic floor spring with complete
accessories for wooden or glass door application of Dorma makes / Approved equivalent makes.Floor
spring should be with adjustable closing force and closing speed.Closing action effectives from approx. 175
degree, with hydraullic sequential control and back check.Including replaceable standard spindle and SS
cover plate with two way action complete inclusive of cutting floor tiles, making the same good and
aligning the door properly.
83 DOORCLOSER-CABIN DOORS-1000 mm EA 2
CONCEALED DOOR CLOSER TO CABIN DOORS : Providing and Fixing Dorma makes concealed door closers
of approved equivalent makes suitable for maximum width of 1000mm.The concealed door closer shall be
integrated in the frame or door leaf, with rapidly decreasing opening resistance.Closing speed and latching
action adjustable, mechanically cushioned limit stay.Adaptation to different rebate clearances
possible.Non-handles ( i.e suitable for right hand and left hand door. ) maximum opening angle 120 degree
complete with all accessories.
Page 87 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
84 STAINLESS STEEL HANDLE: EA 66
STAINLESS STEEL HANDLE: Providing and Fixing stainless steel handle with screws of approved makes etc
complete with all accessories of approved equivalent makes.
85 CP DOOR STOPPER/BUFFER EA 31
DOOR STOPPER / BUFFER : Providing and Fixing in position chrome plated door stopper / buffer with
screws of approved makes etc complete with all accessories of approved equivalent makes.
86 S S HANDLE FOR ENTRANCE DOOR EA 12
STAINLESS STEEL HANDLE FOR ENTRANCE DOOR : Providing and Fixing stainless steel handle for enrance
door with 1000 mm length with screws of approved makes etc complete with all accessories of approved
equivalent makes.
WINDOWS
87 WINDOW JAMB-Gran/Marble17-19mm MR 350
Providing and erecting window cills of 300mm wide in step pattern in Granite / INDIAN marble of 17 to
19mm thick of approved colour & sizes as per drawings for all windows.Granite / INDIAN marble cills to be
fixed in perfect line, level and plumb on required thickness of cement bedding in CM 1:3 as indicated in the
Architectural drawings.Granite / INDIAN marble cill to have 12mm projected from the wall with full round
polished moulded nosing on the entire running length only on internal side and the moulding shall be
machine polished.Basic Rates of Granite / INDIAN marble Rs 1600/- Per Smt.
88 ADJUSTABLE LOUVERS-ALUM COATED SM 2
Providing and installing Aluminum micron powder coated adjustable louvered windows for toilets with
5.0mm thk 100 wide frosted glass louvers with blunt edge and aluminum sections of 16 SWG. anodized to
15 microns in approved colour, all fixed to masonry with teak wood rough ground provided complete incl.
flyproof mesh shutter in frame from inside.The aluminum section thickness shall be of approved thickness
and frame shall be provided for the exhaust fan fixing including cost of all fittings required etc.complete
from all four sides to have 50 x 25mm aluminium powder coated box.
89 ALUM OPENABLE WINDOW/VENTIL. SM 110
ALUMINIUM OPENABLE WINDOWS / VENTILATOR:
Providing & Erecting aluminium openable Windows as per specification as under :
The window shall be consist of Jindal / Hindalco approved extruded aluminium sections of 16 SWG with
double glazing, sound proof arrangement & glazing shall consists of fixed glazing at top and openable
shutter at bottom as per the design and directions including heavy duty stainless steel fraction hinges
required for windows.
Providing and fixing double glazing with glass panels of 6.0 mm & 8.0 mm thick as per IS : 2835 (Saint
Gobin, Modigaurd &Asahi ) for aluminium window for heat insulation including airtightening & silicon
sealing etc complete as per the specifications and the drawings & as directed by Architect.
90 ALUM FIXED WINDOW/VENTIL. SM 15
Same as above but fixed ventilaters as per drawings
91 SUNCONTROL FILM ON GLASS SM 100
SUN CONTROL FILM ON GLASS : Providing and fixing premium grade Garware polyester film or equivalent
approved by architect, on windows / doors etc complete as per the specifications and the drawings & as
directed by Architects / EIC.
LOOSE FURNITURE
TABLES
(ALL TABLES TOP SHALL BE PROVIDED WITH 6mm thk. High durability coloured lacquered glass of Saint
gobain makes or approved equivalent makes.)
Providing & arranging in position table out of 19mm thk marine plywood of approved equivalent makes
including drawer unit, tea-tray, pull-out tray, foot-rest.All drawers to be in marine plywood with 19mm in
front, sides & 12mm thk in rear and bottom and 9mm thk at back.Internal surfaces to be polished in French
polish.Table tops, drawer unit fronts & sides, table sides to be finished as per drawings.Item to be finished
& completed as per drawings & directions.The front modesty panel of the table shall be finished with
Laminate of approved equivalent makes / veneer of Approved equivalent makes as per drgs of the
respective table all complete.
All table shall be provided with M.S powder coated computer key board tray of Approved equivalent
makes.All drawers to have telescopic sliding drawers fittings of approved equivalent makes with Aluminium
concealed profiles for drawer & shutter of Approved equivalent makes, lock with master key of Approved
equivalent makes, colour wire manager of approved equivalent makes & M.S powder coated CPU troley of
Approved equivalent makes.All beading, mouldings and exposed woodwork to be in teak wood.Footrest
shall be made out of 19mm plywood frame work with 6mm top and shall be finished with 1.0mm thk
laminate / 3-4 mm thk Veneer.Item to be completed in all respects as per drawings & instructions.This
Specification is applicable for all tables in item nos. 92 to 101 as mentioned below.
92 TABLE-CLERK/STENO 600X1200X750 EA 36
Page 88 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Providing & fixing clerk table of average size of 600 W x 1200 L X 750 mm H with one drawer box 450 W x
450 L x 750mm H including three drawer of variable height & one openable shutter storage with auto
hinges.Table top, front and sides and other exposed areas finished with 1.0mm thk laminate of approved
shade and make finished as per drgs and instructions from E.I.C.Basic Rate of laminate 450/- per smt.
Page 89 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
93 TABLE-A/B/C OFF.750X1500X750 EA 14
Providing and fixing A/B/C table of average size of 750 W x 1500 L X 750 mm H with one drawer box 450 W x
450 L x 750mm H including three drawer of variable height & one openable shutter storage with auto
hinges.Table top, front and sides and other exposed areas finished with 1.0mm thk laminate of approved
shade and make finished as per drgs and instructions from E.I.C.Basic Rate of laminate 450/- per smt.
94 TABLE-MANAGER: 750X1650X750 EA 8
Providing and fixing Manager table of average size of 750 W x 1650 L X 750 mm H with one drawer box 450
W x 450 L x 750mm H including three drawer of variable height & one openable shutter storage with auto
hinges.Table top, front and sides and other exposed areas finished with 1.0mm thk laminate of approved
shade and makes finished as per drgs and instructions from E.I.C.Basic Rate of laminate 450/- per smt.
95 TABLE-CH/SR MGR:750X1800X750 EA 13
Providing and fixing Chief / Senior manager table of average size of 750 W x 1800 L X 750 mm H with one
drawer box 450 W x 450 L x 750mm H including five nos. of drawer of variable heights.Table top, front and
sides and other exposed areas finished with 3/4 mm thk veneer of approved shade and make finished as
per drgs and instructions from E.I.C.The veneer shall be finished with melamine polish..Basic Rate of veneer
1100/- per smt.
96 TABLE-DGM: 900X1950X750 EA 3
Providing and fixing Director general manager table of average size of 900 W x 1950 L X 750 mm H with one
drawer box 450 W x 450 L x 750mm H including five nos. of drawer of variable heights.Table top, front and
sides and other exposed areas finished with 3/4 mm thk veneer of approved shade and make finished as
per drgs and instructions from E.I.C.The veneer shall be finished with melamine polish.Basic Rate of veneer
2400/- per smt.
97 TABLE-GM: 900X2100X750 EA 1
Providing & fixing General manager / Executive director table of avearge size of 900 W x 2100 L X 750 mm H
with one drawer box 450 W x 450 L x 750mm H including five nos. of drawer of variable heights.Table top,
front and sides and other exposed areas finished with 3/4 mm thk veneer of approved shade and make
finished as per drgs and instructions from E.I.C.The table top veneer shall be finished with polyurethene
polish and rest of the veneer finshed in melamine polish.Basic Rate of veneer 2400/- per smt.
98 TABLE-SECRETARY:1500X750X750 EA 1
Providing and fixing Secretary table of average size of 1500 L x 750 W x 750mm H with one drawer box 450
W x 450 L x 750mm H including five nos. of drawer of variable heights.Table top, front and sides and other
exposed areas finished with 3/4 mm thk veneer of approved shade and make finished as per drgs and
instructions from E.I.C.The table top veneer shall be finished with polyurethene polish and rest of the
veneer shall be finished with melamine polish.Basic Rate of veneer 2400/- per smt.
99 RECEPTION TABLE EA 1
Providing & fixing reception table of average size of 1800 L x 750 W x 900 mmH with one drawer box of 450
W x 450 D x 750mm H including three nos. of drawer of variable height & one openable shutter with auto
hinges.Table top, front and sides and other exposed areas finished with veneer in melamine polish.The top
to be finished with 12mm thk frosted glass with bevelled edges glass supported on 50 mm dia. S.S pipes
with vacuum caps.The apron of the table to be finish with in combination of veneer in melamine polish &
s.s brushed steel laminate of approved make and shade 12mm thk bevelled edges glass to be fixed to this
table with the help of vertical s.s studs as shown in the drawings.Basic rate of Veneer Rs 2400/- Per Smt.
and Basic Rate of Metal Laminate Rs. 2150/- Per Smt.
100 TABLE-DOCTOR :750X1650X750 EA 1
Providing and fixing Doctor's table of average size of 750 W x 1650 L X 750 mm H with one drawer box 450
W x 450 L x 750mm H including three drawer of variable height & one openable shutter storage with auto
hinges.Table top, front and sides and other exposed areas finished with 1.0mm thk laminate of approved
shade and makes finished as per drgs and instructions from E.I.C.Basic Rate of laminate 450/- per smt.
101 TABLE-PHARMACIST:750X1500X750 EA 1
Providing and fixing table for Pharmasict of average size of 750 W x 1500 L X 750 mm H with one drawer
box 450 W x 450 L x 750mm H including three drawer of variable height & one openable shutter storage
with auto hinges.Table top, front and sides and other exposed areas finished with 1.0mm thk laminate of
approved shade and make finished as per drgs and instructions from E.I.C.Basic Rate of laminate 450/- per
smt.
102 PREP.COUNTER-PHARMACY:600X1000 SM 4
Average size of Wide 600mm x Ht. 1000mm
a) STRUCTURE : 19mm thick marine ply board for top sides and modesty panels in joinery & 19mm thk
marineply shelves including glass shutter with teak wood member & sliding channel with aluminium
concealed profiles as instructed with required hardware.
b) CLADDING: 1.0mm thk. Laminate of approved make, shade, texture and design on side, top, drawers,
modesty panel, drawer top etc.Basic Rate of Laminate 450/- Per Smt.
c) FINISHES: Int. surfaces with 3 coats of french polish.
d) FITTINGS & FIXTURES: Sliding channel with guide, aluminium concealed profiles of approved equivalent
& lock with master key & side lock at drawer.
e) VERTICLE GLASS SCREEN : 12 mm thk vertical glass fixed with stainless steel decorative glass holding
brackets as per instruction in all edges of glass to be machine cut polished.
Page 90 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
f) COUNTER TOP : Providing & Fixing 19mm thick granite slab mirror poilshed on one side with moulding on
two sides.Granite top shall have necessary cut to receive 12mm the glass in level Edges of granite to
polished & glass at top surfaces.Basic rate of granite Rs. 1600/- Smt.
103 DOCTOR'SEXAM.BED:1950X600X1200 EA 1
Examination bed with storage below as per drawings & instructions Size :- 1950 L x 600 W x 1200 H mm
a)STRUCTURE to be out of 19 mm thk. Marine plyboards for sides, tops, shutters, etc. supported on 35mm
x 35mm legs out of Marine plyboards. Cladding to be with 1.0mm thk. Laminate for all sides & top, bottom
& all internal surfaces to be finished with french polish.
b)MATRESS : 100 mm thk. rubber foam for bed mattress& 25 mm in arms covered in white cloth .
c) COVERS : cladded in tapestry of approved quality,texture and shade up to Rs.750/- per meter incl. 25
mm/ 40 mm thk. "U" foam for quilting as per design.
104 REST ROOM BED:1800x900 EA 2Providing & fixing rest bed of size 1800L x 900W out of 19mm thk marineply at top & sides, 12mm thk
marineply at bottom with 75 x 75 x 120mm thk teak wood frame from all the sides incluidng
headboard.The top & sides to be finished with laminate.Headboard to be finished with laminate & powder
coated grill.Bed supported with 25mm Dia. stainless steel rod with micron powder coating as per approved
makes, design & drawing with necessary hardware etc. complete as per instruction.Basic rate of Laminate
Rs 450/- Per Smt.
LOOSE FURNITURE :
(ALL TABLES TOP SHALL BE PROVIDED WITH 6mm thk. High durability coloured lacquered glass of Saint
gobain makes or approved equivalent makes.)
Providing & fixing side units of average sizes of 450mm wide x 750mm ht shell out of 19mm thick Marine
Ply on sides, bottom & top fabricated as per detail. Shutters out of 19mm thk Marine Ply for openable
shutter with teak wood lipping patti on shutter edges shutter fixed with self closing hinge full overlays &
19mm thk for sliding shutter with Aluminium concealed profiles ofr shutter & drawer box of Approved
equivalent makes, all sliding channel should have bottom dor guide, stopper of Approved equivalent makes
etc. fixed to the shell and top finished with 1.0mm thk. decorative laminate / 3-4 thk. veneer in melamine
polish.
All Shutters to be provided with required hardware e.g brass towerbolt and brass body lock with master
key Approved equivalent makes, as per instruction.The Back to be out of 9mm thick Marine Ply fixed to the
shell with proper hardware, adhesive & as per details, designs & instructions.Shelves made out of 19mm
thk marine plywood shall be provided on wooden supports whereever directed by EIC or as per drgs.The
exposed surface shall be finished with 1.0mm thick decorative laminate / 3-4mm thk. veneer in melamine
polish of approved make texture, pattern & shade fixed to top, side of shell & shutter with grooves etc. as
per detail including laminated lipping on edges with approved hardware & adhesive etc. Back, shelves &
inside area to be finished with french polish.This Specification is applicable for all tables in item nos. 105 to
109 as mentioned below.
ONLY FRONT PROJECTED AREA SHALL BE MEASURED FOR PAYMENT.
105 SIDE TABLES LAMINATE FINISH SM 45
SIDE TABLES WITH SLIDING / OPENABLE SHUTTERS ( Laminate finish) :Providing and fixing side tables with
combination of sliding shutter or openable shutter with telescopic channel &or auto hinges of approved
makes. Shutter to be finished with laminate as per drawing and instruction.Basic rate of laminate 450/- per
smt.
Page 91 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
106 SIDETABLE VENEER FINISH:Rs1100 SM 10
SIDE TABLES WITH SLIDING / OPENABLE SHUTTERS (Veneer finish) :Providing and fixing side tables with
combination of sliding shutter or openable shutter with telescopic channel or auto hinges of approved
makes .Shutter to be finished with veneer in melamine polish as per drawing and instruction.Basic rate of
veneer 1100/- per smt.
107 SIDETABLE VENEER FINISH:Rs2400 SM 6
SIDE TABLE WITH SLIDING /OPENABLE SHUTTER (Veneer Finish) :Providing and fixing side tables with
combination of sliding shutter or openable shutter with telescopic channel or auto hinges of approved
makes. Shutter to be finished with veneer in polyurethene polish as per drawing and instruction.Basic rate
of veneer 2400/- per smt.
108 REARCREDENZA VINEER FIN:Rs1100 SM 30
REAR CREDENZA WITH SLIDING / OPENABLE SHUTTER (Veneer Finish) :Providing and fixing rear credenza
with combination of sliding shutter, openable shutter and drawer box of 450 W x 450 L x 750mm H
including five nos of drawer of variable height with telescopic channel & auto hinges of approved
makes.Shutter and drawer box finished with veneer in melamine polish as per drawing and instruction
.Basic rate of veneer 1100/- per smt.
109 REARCREDENZA VINEER FIN:Rs2400 SM 10
REAR CREDENZA WITH SLIDING / OPENABLE SHUTTER (Veneer finish) : Providing and fixing rear credenza
with combination of sliding shutter, openable shutter and drawer box of 450 W x 450 L 750mm H with five
nos of drawer of variable height with telescopic channel & auto hinges of approved makes.Shutter and
drawer box finished with veneer in polyurethene polish as per drawing and instruction.Basic rate of veneer
2400/- per smt.
110 LOWLEVEL STOR.CABINET-LAMINATE SM 95
SHELL :-Shell out of 19mm thk marine Ply & Back out of 9mm thk. marine ply with 19mm thk. block board
openable / sliding shutters with adjustable shelves out of 19mm marine Ply finished with necessary teak
wood beading with brass oxidised piano hinges / Auto hinges / Self closing hinges in approved angle, locks
with master keys, handles, tower bolts, magnetic catches, all sliding in the powder coated aluminium
channel having smooth bearing movement Approved equivalent makes, master lock of approved makes.
Back, shelves & inside area to be finished with french polish.6mm thick teak wood lipping to be provided
inside & on all exposed surfaces.Top out of 19mm thk. marine ply finished in 1.0mm thk. laminate.
CLADDING : 1.0mm thk laminate of approved make / veins fixed to shell & shutter with grooves in any
pattern & design etc. as per detail inclusive Teak Wood lipping on edge with necessary hardware, adhesive
and finished with approved shade.Back, inside polished with 3 coats of french polish. Basic Rate of
Laminate 450/- Per Smt.This Specification is applicable for all tables in item nos. 111 to 114 as mentioned
below.
ONLY FRONT PROJECTED AREA SHALL BE MEASURED FOR PAYMENT.
Providing & fixing Low storage with Laminate finish SIZE: Average 450mm D x Height & Length as per drgs.
111 LOWLEVEL STOR.CABINET:Rs 1100 SM 17
LOW LEVEL STORAGE CABINET OPENABLE / SLIDING SHUTTER (Veneer Finish) : (450mm D.) : Same as Item
No. 110 above but Providing and fixing Low storage finished with Veneer 3 to 4mm thick in melamine
polish.Basic rate of veneer Rs. 1100/- per smt.
112 LOWLEVEL STOR.CABINET:Rs 2400 SM 10
LOW LEVEL STORAGE CABINET OPENABLE / SLIDING SHUTTER (Veneer Finish) : (450mm D.) : Same as Item
No. 110 above but Providing and fixing Low storage finished with Veneer 3 to 4mm thick in melamine polish
and table top to be finish in polyurethene polish.Basic rate of veneer Rs. 2400/- per smt.
113 FULL HGT. STORCABINET LAMINATE SM 80
FULL HEIGHT STORAGE CABINET (Laminate finish): (500mm D.) : Specification Same as Item No. 110 above
but Providing and fixing full height storage finished with 1.0mm thk Laminate of approved make and
shade.Basic rate of Laminate Rs. 450/- per smt.
ONLY FRONT PROJECTED AREA SHALL BE MEASURED FOR PAYMENT.
114 FULL HGT. STORCABINET VENEER SM 30
Page 92 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
FULL HEIGHT STORAGE CABINET (Veneer finish): (500mm D.) : Specification Same as Item No. 110 above
but Providing and fixing full height storage finished with veneer 3 to 4 mm thk in melamine polish of
approved make and shade.Basic rate of veneer Rs. 1100/- per smt.
ONLY FRONT PROJECTED AREA SHALL BE MEASURED FOR PAYMENT.
SOFA SIDE TABLE :
a) STRUCTURE :Providing & arranging in position side table out of 19 mm thk. Marine Ply box type structure
for side, top, shelves & back with 6mm thk marine ply at support of neccesary teak wood frame with
proper joinery & hardware structure of any shapes as per drgs and directed by E.I.C.
b) CLADDING: All exposed plywood surface to be finished with 3-4 mm thk. veneer in melamine polish.The
Top to be finished with 12 mm thk. tinted Float / coloured glass edges ot be machine polished.Basic Rate of
Veneer approx. Rs.2100/- per smt.
115 SIDE TABLE 450 WX450LX500mm H EA 1
Providing Side Table size: 450 mm wide and 450 mm long x 500 mm H .As per dwg.
116 SIDE TABLE 600 WX600LX500mm H EA 5
Providing Side Table size: 600 mm wide and 600 mm long x 500 mm H.
CENTRE TABLE:
117 CENTRETABLE 500 WX900LX500mm H EA 1
a) STRUCTURE: Cicular / Rectangular / Oval type structure of any shapes centre table Out of 6mm thk
marine ply finished with 3/4mm thk veneer supported by 40 mm x 75 mm best quality Teak Wood frame
with proper joinery & hardware.
b) TOP: 19mm thk Marine ply at supports of teak wood frame & veneer to be cladded finish with melamine
polish with 12 mm thk. Tinted coloured / clear glass at top & edges finished with machinery polish.
c) FINISH: wooden frame & veneer to be polished in melamine finish of approved shade. The item shall
include providing and applying two coats of wood preservative paint each on all the surfaces of the ply and
wood.Basic rate of veneer 2400/- SMT.
ii) size: 500 mm wide & 900 mm long x 500 mm H.
118 CENTRETABLE 600 WX600LX500mm H EA 3
Same as item no.117 above but size 600 mm wide & 600 mm long x 500 mm H .As per dwg.
MEETING / CONFERENCE ROOM TABLE:
Providing & arranging in position syndicate meeting room tables with top out of 19mm thick Marine Ply &
support out of necessary country wood frame work with necessary beading, mouldings at edges of ply.The
table top edges will be fixed with 40 x 75 group matching veneer teakwood moulding.Top support shall
include a second layer of 19mm thk. Marine plyboard of width at least 200mm all periphery of the
table.Top to be finished with 12mm thk corian.The side to be with two layers of 6mm thk. Marine plyboard
finished with veneer of approved shade ply to be supported by Country wood frame work.Marineply
finished with veneer in melamine polish of approved shade including necessary additional supports, best
quality Teak Wood beadings, mouldings, foot-rests, etc. as per drawing and design.
Side & leg to be finished with group matching veneer of approved shade / veins finished with melamine
polish of approved shade in any pattern , shapes & design.
Item to be completed in all respects as per the drawings & directions.( Basic rate of veneer shall be approx.
Rs.2400/- per smt. & Basic rate of corian Rs. 7000/- per smt. )
119 MEET/CON TABLE1050WX1050LX750H EA 1
Size: 1050 L x 1050 W x 750mm H.
120 CASH COUNTER750WX1500LX1200H EA 1
a) STRUCTURE : 19mm thick marine ply board for top sides and modesty panels in joinery as instructed
with required hardware including on M.S. frame with 25 micron powder coating made from 12mm x12mm
sqaure bars which shall be fixed to the ply board shell.
b) CLADDING: Half part of 1.0mm thk. Laminate & Veneer of approved make, shade, texture and design on
side, top, drawers, modesty panel, drawer top etc.Basic rate of Veneer 1100/- Per Smt. & Basic Rate of
Laminate 450/- Per Smt.
c) FINISHES: Int. surfaces with 3 coats of french polish, external veneer in melamine polish.
d) FITTINGS & FIXTURES: brass oxidised butt hinges, handled, master lock & side lock at drawer of
approved makes.
e) VERTICLE GLASS SCREEN : 12 mm thk glass ones counter with etching 50% glass area fixed with stainless
steel decorative glass holding brackets as per instruction company in all edges of glass to be machine cut
polished.
f) COUNTER TOP : Providing & Fixing 19mm thick granite slab mirror poilshed on one side with moulding on
two sides. Granite top shall have necessary cut to receive 12mm the glass in level Edges of granite to
polished & glass at top surfaces.
121 MAIL DISPATCH TABLE 750 MM WIDE MR 3
Providing & fixing counter table with 750 mm wide top with 19mm thk. marine plywood with 25 mm thk
teak wood beading including 6mm thk clear glass at top finish with laminate of approved colour and side
back made out of 19 mm thk marine plywood.Every four feet of length of the counter shall be provided
with a drawer box of size 450 x 450 x 750 mm ht of five nos. of drawer of variable height.Each table space
shall be provided with computer key board tray, cpu unit, wire manager of approved make.All exposed
surface includings counter sides, drawer box shall be finished with 1.0mm thk laminate of approved shade
and all internal surface to be finished with french polish.Basic Rate of Laminate 450/- Per Smt.
Page 93 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
122 PIGEONHOLE FOR MAIL-19MM MAR MR 15
Page 94 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Providing & fixing pigeon hole for mail made out of 19 mm thk. marine plywood for the outer frame and 19
mm marine plywood for internal divisions with cubicle size 200mm x 200mm with 375 mm deep. There will
be a stack of 3 cubicles in one column, the total height of column will be 900 mm. The measurment will be
done along the row of such columns. All exposed surfaces to be finished with 1.0mm thk. laminate and all
internal surfaces including the pegion holes shall be finished with 1.0mm thk laminate of approved shade.
complete in all respects as per the drawing and the directions of the EIC.Basic Rate of Laminate 450/- Per
Smt.
123 SOFA: 1800 mm x 750 mm with arms EA 6
a) STRUCTURE: Providing & arranging in position sofas with internal frame out of size 75 x 38 mm Teak
Wood frame for seat, back & arms with 9mm thk. Marine ply cladding for facade, side & back or as
mentioned in the drawing with reqd.hardware.The item shall include providing and applying two coats of
fire retardant panit and wood preservative paint each on all the surfaces of the ply and wood.
b)CUSHION: 75 mm thk. Rubber / Polyurethene foam in seat / back & 25 mm in arms / lattest rubber foam
of appropriate thickness as shown in the drawing with melamine polish on all exposed wooden surfaces
covered in white cloth over never strip and GI flat spring fixed to the frame with reqd. hardware etc
complete.
c)COVERS: Sofas to be cladded in fabric tapestry / upholstery / leather of approved quality, texture and
shade up to Rs.950/- per meter including 25 mm / 40 mm thk. "U" foam for qualitiy as per design.
124 SOFA : 1500 X 750 mm with arms EA 2
a)STRUCTURE: same as 123.a
b)CUSHION: same as 123.b
c)COVERS: same as 123.c but with Tapestry of approx.Rs. 950/- per meter.
125 SOFA : 750 X 750 mm with arms EA 3
a)STRUCTURE: same as 123.a
b)CUSHION: same as 123.b
c)COVERS: same as 123.c but with Tapestry of approx. Rs.950/- per meter.
126 XER/PRT/FAX COUNTER-750mm D SM 5
XEROX / PRINTER / FAX COUNTER (Laminate Finish) : (750mm D.)
SHELL :-Shell out of 19mm thk marine Ply and Back out of 9mm thk. marine ply with 19mm thk block board
openable / sliding shutters and adjustable shelves out of 19mm marine Ply finished with necessary teak
wood beading with brass oxidised piano hinges / Auto hinges in approved angle, locks with master keys,
handles, tower bolts, magnetic catches, all sliding in the powder coated aluminium channel having smooth
bearing movement, master lock of approved makes.Back, shelves and inside area to be finished with french
polish.6mm thick teak wood lipping to be provided inside and on all exposed surfaces.Table Top out of
19mm thk marine ply finished laminate with approved colour & makes.
CLADDING : 1.0mm thk laminate of approved make/ veins fixed to shell and shutter with grooves in any
pattern and design etc. as per detail inclusive Teak Wood lipping on edge with necessary hardware,
adhesive and finished with approved shade.Back, inside polished with 3 coats of french polish. Basic Rate of
Laminate 450/- Per Smt.
ONLY FRONT PROJECTED AREA SHALL BE MEASURED FOR PAYMENT.
Providing & fixing Low storage with Laminate finish SIZE: 750mm D x Height & Length as per drgs.
FALSE FLOORING / CEILING
FALSE CEILING
127 FALSECEILING-600X600mm AL POW SM 50
FALSE CEILING: Providing and Fixing of approved colour & makes as per consultant Lay-in Tile Perforated
False Ceiling on 15mm ‘T’ Framework of module 600mm x 600mm. Panels aluminium powder coated
perforated tiles shall be manufactured of size 584 mm x 584 mm made out of 0.7mm thick Aluminium Alloy
3105. The perforation in tile shall be 1.5mm dia in a 3mm diagonal square pattern giving 22%-perforated
area. The Tile will be manufactured on equipment, which includes several levelling. The tile end shall be
raised upward by 8mm and bend outward to lay the tile in framework.
The Tile shall be Polyester based, powder coated in white colour.Grid system for fixing ceiling tiles shall
comprise of Tees.The 15 mm main tee runners shall be suspended at an interval of 1200mm centre to
centre. The 15 mm cross tee runner shall be suspended at 600mm centre to centre and further supported
with 15 mm cross tee at 600mm centre to centre with interlocking arrangements to form grid of 600mm x
600mm. The main tee shall be supported by means of 4mm G.I. rod from slab/roof. The suspension shall be
provided at 1200 to 1500mm centre to centre.
The item shall include providing Non-woven felt made of glass-reinforced fibre glued over the perforation
for sound absorption.The item shall be completed as per manufactures specication.Basic rates with all item
required for false ceiling Rs.1900/- Per Smt.
NOTE : RATE TO INCLUDE PROVIDING OPENING FOR A.C.SUPPLY / RETURN AIR GRILLS, LIGHT FITTINGS and
FIXTURES.
128 FALSECLG Multip'C' ALUM Micro SM 480
FALSE CEILING : Multiple "C" Aluminium, Micro-perforated tiles with non woven textile acoustic felt.
Page 95 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Providing and fixing of approved colour & makes as per consultant Multiple "C" 225 / 300C Micro
Perforated Aluminium panel perforation of 1.5mm diameter and 3mm centre to centre manufactured
consisting of panel 225mm wide x 15.5 mm deep x 0.6mm thick with bevel edge, panel length up to 6 mtr,
Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance
aluminium alloy AA 3005 (Al. Mg) for higher strength and good roll forming characteristics.
The Panels shall be each other with a narrow V grove.Panel shall be clipped to a baked enamelled
aluminium Panel carrier of 32mm wide x 39mm deep x 0.95mm thick in standard length of 5 mtr made of
doubled baked enamelled aluminium alloy AA 5050 (Al. Mg) black with cut outs to hold the panels in a
module of 75 / 150 / 225mm closed at a distance 1.00 mtr. Panel carrier shall be suspended by means of
G.I. suspension rod 4mm diameter and a Galvanised suspension spring clip at a distance of 1.7 mtr c/c
Paint Finish: Aluminium panels shall be chromatised for maximum bond between metal and paint,
enamelled twice under high temperature, one side with a full primer and finish coat the other side (inner
side) with a primer coating and Skin Coat on a Continuous Paint Line.
Acoustic Felt: Non-woven felt made of glass-reinforced fibre glued over the perforation for sound
absorption.
Page 96 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Mode of Measurements: Measurements shall be wall to wall without any deductions for lights, diffusers,
columns etc.Basic rates with all item required for false ceiling Rs.2900/- Per Smt.
NOTE : RATE TO INCLUDE PROVIDING OPENING FOR A.C.SUPPLY / RETURN AIR GRILLS, LIGHT FITTINGS and
FIXTURES.
129 GYP BOARD FALSECEILING-12.5MM SM 100
GYPSUM BOARD FALSE CEILING :
Providing and fixing in position Gypsum Board False ceiling as per manufacturer's specification and
instruction with 12.5 thick 'Gypboard' Screw fixed to the underside of suspended G.I grid should be
constructed and suspended from the main ceiling as per manufacturer's instruction and specification.G.I
grid should consist of ceiling section ( India Gypsum Code Nos. MF5 ) at maximum centre to centre
distance 1200mm.The ceiling section should be fixed to intermediate channels with connectings clips (
India Gypsum CodeNos. ME9 ) G.I grid should be fixed to R.C.C slab above with the help of 25 x 0.5mm
strap hanger ( India Gypsum code Nos. MF8 ) and soffit cleat ( India Gypsum Code Nos. P534 ).
The joints between soffits cleat and strap hamger and G.I grid and strap hanger should be with 6.4 x
12.7mm nut and bolts ( India Gypsum Code Nos. P526 ).Soffits cleats should be fixed to R.C.C ceiling with
W.E type 12mm Dia. 17/16" long steel Rawl plug maximum centre to centre distance ( both ways ) of strap
hangers should be 1200mm.The 'Gypboard' to be used should be 12.5mmthk. tapered edge boards.
The boards shoule be taped and filled from underside to ceiling.Item to be completed as per
manufacturer's specification and instruction.The rate should be include necessary additional ceiling
sections and intermediate channels should be provided at openings for light fixtures,A.C ducts,vertical
drops,offsets etc.Additional intermediate channels should be fixed to strap hangers for additional support
to prevent starp hangers from bucklings / swaying at every 1200mm.Item to be completed in all respect
including necessary sleeves for ducts finishing of joints cuts outs supports for A.C.
Note :- No extra will be paid for ceiling drops and it will be considered as flat ceiling and if there is projected
drop ceiling curved as per design in different level it will also be paid as addition to that but only average
bottom surface area will be considered.No extra will be paid for light cutings ,cutting of glass or satin glass
.No extra channels will be paid if its is required for addtiotional supports.Gypboard shall be fitted and
finished with one coat of primer and 3 coats of plastic / acrylic emulsion paint.
NOTE: RATE TO INCLUDE PROVIDING OPENING FOR A.C.SUPPLY / RETURN AIR GRILLS, LIGHT FITTINGS and
FIXTURES & ANY SHAPE / DROPS.
130 CAL SILICATE FALSECEILING- 8MM SM 400
CALCIUM SILICATE BOARD FALSE CEILING (HILUX ):
Providing and fixing Calcium silicate board of 8mm thick of approved equivalent makes as epr consultant
regular frame of suspended ceiling comprisis of galvanized steel `perimeter channel of having .55 mm
thickess and unequal flanges fixed to walls/partiion using nylon sleeves and screws at 450 mm centers.The
intermedite channel (.91 mm thick ) having two equal flanges of 15 mm each and web of 45 m is
suspended from th ofit at 1220 mm wit ceiling angle of width 25 mm x 10 mm x .5 mm fixed with cleat and
steel expansion fasternes.
The calcium silcate board to be fixed along /acroos the ceiling sections with 25 mm long self driling and
tappings screws at 200 m c/c .The joints to be finished with 48 mm wide fibre tape to provide seamless
finish.Additional perimeter channel and suporting materials are to be provided to mke any opening for light
fittings,diffusers etc. The frame work to be supported properly to maitain the integrity o ceiling and shall
be at no extra cost.Rate shall include joining tape and compound.The item shall be paid ony on the finshed
surface only and any watsge will be in contractors scope.
Page 97 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Note :- No extra will be paid for ceiling drops and it will be considered as flat ceiling and if there is projected
drop ceiling curved as per design in different level it will also be paid as addition to that but only average
bottom surface area will be considered.No extra will be paid for light cutings ,cutting of glass or satin glass
.No extra channels will be paid if its is required for addtiotional supports.board shall be fitted and finished
with one coat of primer and 3 coats of plastic / acrylic emulsion paint.
NOTE: RATE TO INCLUDE PROVIDING OPENING FOR A.C.SUPPLY / RETURN AIR GRILLS, LIGHT FITTINGS and
FIXTURES and ANY SHAPE / DROPS.
131 CELL-CEILING-AL POWDER CT75X75 SM 5
FALSE CEILING : Aluminium Powder Coated CELL CEILING 75 x 75.
Providing and fixing Aluminium cell ceiling of approved colour makes or approved makes as per consultant
consisting of main runner, cross runner, upper sections, lower sections all of u-sahped profiles 10mm wide
x 50mm deep x 0.5mm thick with inwardly returned edges of 2.5mm.Coil coated on a continuous paint line,
double baked and roll formed from enameled corrosion resistance aluminium alloy (Al.Mg) for higher
strength and good roll forming characteristics.The main runner shall be fixed at a distance of 1.2mtrs. c/c
and shall be suspended by means of G.i suspension rod 4mm diameter and a Galvinized suspension spring
clip at a distance of 1.2mtrs c/c.The cross runner shall be fixed to the main runner at a distance 0.6mtrs c/c,
with a self-locking deviceThe upper section and lower shall be fixed to the main runner and cross with a
self-locking device.
Providing and fixing 75 x 75mm module grid cell ceilings of Hunter Douglas / approved equivalent in
approved shade and colour.The ceilings shall be supported by GI wires fixed to the RCC slab and with
adjustable clips. Complete as per manufacturers instruction and direction of Architects.Basic rates with all
item required for false ceiling Rs.3600/- Per Smt.
132 FALSE CEILING RAFTER SM 50
Providing and fixing false ceiling of 6mm thk. Acrylic sheet box fixed on Stainless steel studs with Stainless
steel wire ropes with necessary fitting required for this items.
133 SILHOUETTE BLIND-CH 81WX61D SM 35
Providing and fixing of approved equivalent makes as per consultant Silhouette Shades Blinds of approved
shade as per the following specification:
The blind shall be one part blind, one part drapery and shall be made of soft sheer fabric front and back
facings, bonded to translucent fabric vanes.Silhouette shade shall be operated using a continuous cord
loop and with the shade lowered, the vanes could be tilted to any position from fully open to closed. With
the vanes open , the sheer fabric facings shall soften the outside view and filter the incoming sunlight. With
the shading raised, the fabric shall be concealed into the headrail.All components are to be colour co-
ordinate and the specification is as follows.
Headrail : Channel shall measure 81mm wide and 61mm deep with a normal wall thickness of 1.0 – 1.2mm
& extruded from 6063 aluminum alloy with powder coated finish.Cord Tendioner/Cartridge Assembly.The
assembly consists of the following components : Cord Tensioner : Cord Tensioner Body, Cord Tensioner
Cover, Cord Tensioner Spring, Cord Tensioner Cradle, Cord Tensioner Spool, Loop Cord.Cartridge Assembly :
Cartridge, Cord Wheel Shaft, Cord Wheel, Cord Wheel Cover.
-Clutch /Limit Assembly Set
Clutch/Limit Assy : Made from high engineering grade plastics and consist of the cord pulley and the limit
adjustment and levelling screw.
Any assembly consist of the following :
Clutch Side : Right or left Specific Headrail End Cap Cord Pulley, Screw, Torsion, Spring, Spring Release.
Limit Side : Right or Left Specific Headrail End Cap, Right or Left Specific Back Plastic Screw, Right or Left
Specific Limit Nut, Limit Adjustment Screw, Spring, Screw Limit Bracker, Rotator, Right or Left Specific
Fabric Sensor, Leveling Screw.Basic Rate of Blinds 10000/- Per Smt.
134 WINDOW BLINDS-100 MM WIDE SM 80
Providing and fixing window blinds of 100 mm wide vertical blinds / chiks / bamboo / fabric / roman / roller
of approved shade & makes with scoth gaurd fabric protector.The blinds to be fixed and commissioned as
per manufactures specification.The work to be completed as per satisfaction & approval of the EIC.Basic
rate of blinds - Rs 2000/- Per Smt.
PAINTING:
135 Acrylic emulsion paint SM 1200
Providing and Applying Painting the entire premises in 3 coats of acrylic emulsion paint of approved quality,
shade over one coat of primer and leveling course. Rate to include scrapping wall surfaces, applying putty
for proper finish, applying necessary. coat of primer to get firm surface to receive paint.Providing &
Applying Painting the entire premises in 3 coats of acrylic emulsion paint of approved quality, shade over
one coat of primer and leveling course. Rate to include scrapping wall surfaces, applying putty for proper
finish, applying necessary. coat of primer to get firm surface to receive paint.
136 LUSTRE PAINT-SUP QUALITY SM 100
Providing and applying 3 coats of superior quality of lustre paint of approved make and shade, lustre finish
and to give an even shade including preparation of surface, applying cement- primer of approved make
etc., complete as per directions & manufacturer's specifications. Rate to include additional coat od paitns
in any requried to get smooth and uniform finish.
137 LACQUER PAINT SM 50
Page 98 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Painting specified areas in 3 coats of lacquer paint of "DUCO" or approved make quality, shade over metalic
surfaces / wooden surfaces after preparing the surfaces with water proof putty to get proper
surfaces,applying necessary coats of primer and finishing with matt / textured finish laquer paints.
138 SPECIAL EFFECT PAINT SM 50
Providing & Applying Special effect paint of Asian Royal make / approved equivalent makes.Painting the
specified area in 3 coats of special effect paint by making the necessary surface of wall to receive the
special effect paint as per direction of manufactures.
139 POP PUNNING-WALLS, COLM, etc. SM 450
Providing and applying plaster of paris punning in average of 12mm thickness on walls, ceiling, beams and
columns to bring the surface in plumb line and level, including making the surface smooth, providing
required grooves on top of skirting etc. complete as per directions. (Note :- Rate to include cost of
scrapping any finished on the existing plastered surface and hacking the surface.)
140 POP MOULDING-125-150MM HIGH MR 25
Providing & Casting 125 to 150 mm high decorative POP molding with Jute reinforcement as per detail &
fixing the same to the walls / ceiling with brass screws incl. finishing with 3 coats of acrylic emulsion paint.
MISCELLANEOUS
141 FRPplanter255X255X205 to 255mm EA 20
Supplying FRP planters of 255W x 255L x 205H mm to 255 mm of approved, colour and shape with proper
draining arrangement at the bottom.
142 Lacquered brass planter EA 10
Same as above but lacquered brass planters of approved shape and size.
143 WOODEN PLANTER 305X305X400 mm EA 10
Providing & Arranging planter 305W x 305L x 400H mm out of 19mm thk. Marine Ply cladded with veneer of
approved veins & best quality Teak Wood lipping & moulding, polished in melamine finish external &
french polish internal.
144 ARTIFICIAL PLANT upto 1100mm H EA 20
Providing and arranging artificial plants like creepers, leaves etc. In Plastic pots with marble / stone
pebbles, moss etc. as per approval and selection.
145 ARTIFICIAL PLANT upto 1500mm H EA 20
Same as item no. 144 above but Big Plants upto 1500mm HT
146 Bush&Creepers upto 300mm H EA 20
Same as item no. 144 above but Medium bushes and Creepers upto 300 mm Height
147 MURALS / PICTURES EA 5
Providing and arranging artificial murals or pictures made up of pvc plastic with good design as per
architect approval.Basic Rate of Murals Rs. 35,000/- Per Nos.
Page 99 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
148 SS PERFORATED DUSTBIN-200mm EA 80
Providing and arranging Dustbin of 200 / 225 mm dia Stainless steel 304G perforated dust bins of approved
quality as per directions of EIC/Architect.
149 IN OUT TRAYS 225mmX350mmX400mm EA 5
Providing & arranging in position in-out trays made out of 12mm thk marine plywood of size 225mm W x
350mm L x 400mm H ( one for in & one for out ) and finished with veneer in melamine polish including
necessary TW members finished with melamine polish etc; complete in all respects as per instruction from
E.I.C.Basic Rate of Veneer Rs. 2400/- Smt.
150 IN OUT TRAYS 225mmX350mmX400mm EA 13
IN OUT TRAYS: Providing & arranging in position in-out trays made out of 12mm thk marine plywood of
size 225mm W x 350mm L x 400mm H ( one for in & one for out ) and finished with veneer in melamine
polish including necessary TW members finished with melamine polish etc; complete in all respects as per
instruction from E.I.C.Basic Rate of Veneer Rs. 1100/- Smt.
151 IN OUT TRAYS 225mmX350mmX400mm EA 61
Providing & arranging in position in-out trays made out of 12mm thk marine plywood of size 225mm W x
350mm L x 400mm H ( one for in & one for out ) and finished with veneer in melamine polish including
necessary TW members finished with melamine polish etc; complete in all respects as per instruction from
E.I.C. Basic Rate of Laminate Rs. 450/- Smt.
152 MAIN SIGNAGE EA 3
Providing and fixing main corporate signage with approved letter made out of brushed steel / S.S finished
letter of logo of approved size & fixed in position with 6 nos. S.S studs of approved quality as per directions
of EIC / Architect.
153 INTERNAL DOOR SIGNAGE EA 35
Providing and fixing internal door signage made out of brushed steel / S.S finished letter of logo of
approved size & fixed in position with 2 nos. S.S studs of approved quality as per directions of EIC /
Architect.
154 AIG POSTER SM 18
Providing and fixing in position posters printed on vinyl & stuck betwwen 2 nos. 4mm thk clear acrylic
sheets with 4 nos. studs of approved quality as per directions of EIC / Architect.
155 GrillRolling Shutter-5mm th MS SM 10
Providing and fixing grilled rolling MS shutters out of 5mm thk. MS flats & 12mm dia. MS bars as per design
for entrance door of the office complete including rolling gears, springs & box at top & with mechanical
rolling arrangement with box and handle.The shutter shall have locking arrangement at the bottom sides
with dead lock as approved by the architect etc. complete including enamel paint of approved shades as
per directions of EIC / Architect.
156 CURTAIN RODS-POWDER COATED: RMT 30
Providing and fixing in position approved equivalent brand powder coated string sliding curtain rods with
decorative side knob fixed on Metal brackets complete including line, level etc. as per instructions.
157 CURTAINS: Rs 500 SMT 10
Providing and fixing in position curtains of American pleats for windows from the approved fabric including
necessary lining tapes etc. complete.
NOTE : Basic rate of fabric having standard width, approx. Rs. 500/- per RMT.
ELECTRICAL WORK
Notes:
a) Rates quoted should be inclusive of Supply, Installation, Testing and Commissioning of items
Specified in a Bill of Quantity.
b) Running meter charges will be paid at actual measurements.
POINT WIRING AND CONDUITING WORK
Supplying, Installation, Testing and Commissioning of point wiring for light / call bell / exhaust fan points
with 2 x 1.5 sq.mm. 1100V grade PVC insulated colour coded stranded copper conductor FRLS wires made
to IS:694 and continuous 1.5 sq.mm. copper conductor green coloured PVC insulated earth wire to run
inside heavy gauge 25mm PVC conduit pipes of low halogen smoke of suitable size, from switch Board to
point via controlling SP switch, including PVC conduits and accessories like couplers, Elbows, junction boxes
etc. above false ceiling and in concealed manner on wall / partition using 6A modular type switch mounted
on concealed metal box including required numbers of BLANK SWITCH for closing the extra module as
below:
158 1 Pt ctrl by 1 No. 6 A switch EA 30
One point controlled by one No. 6 Amp switch
159 2 Pt ctrl by 1 No. 6 A switch EA 60
Two points controlled by one No. 6 Amp switch
160 3 Pt ctrl by 1 No. 6 A switch EA 25
Three points controlled by one No. 6 Amp switch
161 4 Pt ctrl by 1 No. 6 A switch EA 34
Four points controlled by one No. 6 Amp switch
162 10 Pt ctrl by 1 No. 6 A switch EA 4
Ten points controlled by one No. 6 Amp switch
163 EXHAUST/WALL FAN POINT EA 80
Exhaust Fan point controlled by one No. 6 Amp switch and 6A 5pin socket near exhaust fan.
CIRCUIT WIRING
Page 100 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Supply and Laying of PVC insulated Copper wire drawn in heavy gauge 25mm PVC conduits pipes of Zero
halogen Fire retardant (FRZH) from distribution board to lighting switch boards / power sockets including
conduits and all required accessories.
164 1 circuit 2X2.5+1.5sqmm wire MR 1000
Page 101 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Circuit wiring with One no. circuit of 2 x 2.5 + 1.5 sq.mm wire in 25mm conduits.
165 2 circuits 2X2.5+1.5sqmm wire MR 10
Circuit wiring with Two nos. circuit of 2 x 2.5 + 1.5 sq.mm wire in 25mm conduits.
166 1circuit 2X4.0+2.5 sqmm wire MR 500
Circuit wiring with one no. circuit of 2 x 4.0 + 2.5 sq.mm wire in 25mm conduits.
167 3CX2.5 sqmm Cu flexible cable MR 3000
3C x 2.5 sqmm Cu flexible cable through raceways / 25mm conduits for power points.
Supply and Installation of wiring from monument box/ Switch socket outlets to distribution board with
3core x 2.5 sq.mm copper wire drawn in under floor raceways / conduits.
168 6A SWITCH SOCKET EA 90
Supply and Installation of 6 Amp single switch socket along with plate outlet with G.I. box recessed on
partition/wall.
Page 102 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
169 6 / 16A SWITCH SOCKET EA 30
Supply and Installation of 6/16 Amp switch socket outlet along with palte with G.I. box recessed on
partition/wall.
170 WORK STATION POINT EA 90
Supply and Installation of group of plug points for computer with modular type, 5pin 6Amp universal
Socket x 3 Nos. + 6/16A universal socket x 1no. to be installed on provided monument box / below table in
partition with 2nos. 16Amp switches (with indicator) to be installed recessed on partition wall above table
above side units with metal box .
171 20A Reroll Plug-Sockets EA 6
20A Reroll Plug-Sockets with Top Housed in metal board with 16A SP MCB. For ACs/ Kitchen load
172 32A Reroll Plug-Sockets EA 2
32A Reroll Plug-Sockets with Top Housed in metal board with 32A SP MCB. For Kitchen load
173 16A Indust type,Plug-Socket EA 4
16A Industrial type, PVC molded Plug-Sockets with 3 Pin Top Housed in metal board with 16A SP MCB. For
Racks
LIGHT FIXTURES
Supply and Installation of the following fixtures completely wired with chokes, roller lock type holder,
Lamps / fluorescent tubes and chain supports from ceiling wherever necessary.
174 SPOTLIGHT 2X18 WATTS 180mm Dia EA 100
Recessed type spot light concealed fitting with 2 x 18 Watts CFL lamps with electronic ballast & centre
frosted glass of Philips / Tulips / Thorns/Wipro make or Approved equivalent.
175 SPOT LIGHT 2 x 18W - DIMMABLE EA 6
Recessed type spot light concealed fittings with 2 x 18 Watts CFL, Tulips make / Approved equivalent HF
with electronic dimmable ballast of Philips / Tulips / Thorns/Wipro make or Approved equivalent.
176 DIR/INDIR 2X24W T5 600X600mm EA 100
DIRECT/INDIRECT 2 x 24W T5 ( 600 x 600mm ): Recess mounted indirect /direct luminar,2x24w T5 lapms,
having high efficiency diffuser giving more than 81% efficiency with duly wired electronic ballast having <
10% THD with strike time >= 0.4 Sec of Philips / Tulips / Thorns/Wipro make or Approved equivalent.
177 DARKLIGHTER 2X28W T5 FTL EA 40
DARK LIGHTER 2 x 28W T5 FTL Recessed twin dark lighter mirror optics concealed fittings with 2 x 28 Watts
T5 FTL, Tulips makes or Approved equivalent.HF with electronic ballast of Philips / Tulips / Thorns/Wipro
make or Approved equivalent.
178 LED SPOT LIGHT EA 10
Recessed LED down lighter 3 Watt, wich gives Halogen light effect Philips / Tuliip / Thorns / Wipro make or
approved equivalent.
179 MIRROR LIGHT 1X11 W TFW EA 4
Wall mounted mirror light with 1 x 11 Watt TFW of Tulips approved makes or Approved equivalent with
electronic ballast of Philips / Tulips / Thorns/Wipro make or Approved equivalent.
180 SINGLEPATTI FIXT-1X28 W TUBE EA 20
Single Patti fixture with 1 x 28 Watt tube, Tulips Makes Approved equivalent with electronic ballast of
Philips / Tulips / Thorns/Wipro make or Approved equivalent.
181 PICTURE CANDLE LIGHT-20 W EA 10
Wall mounted picture candle light fixture with 12V / 20Watts of Tulips makes or Approved equivalent with
electronic ballast of Philips / Tulips / Thorns/Wipro make or Approved equivalent.
182 EXHAUST FANS - 9 INCH DIA EA 8
Providing and fixing of heavy duty Exhaust fans of window mounted type with bird screen and louvered
shutters – 9 inch dia of approved make and colour or Approved equivalent.
183 CHANDELIER TYPE LGT FIX EA 1
Providing and fixing chandelier type light fixture of approved design and make or Approved equivalent with
including lamp. (Basic rate Rs 20000)
Page 103 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
184 WALL MOUNTED PICTURE LIGHT EA 20
Providing and fixing picture light of approved design and make with lamps or Approved equivalent.Basic
price Rs 3000/- Per Nos.
185 FLOOR MOUNTED LED LIGHT EA 10
Providing and fixing floor mounted LED light of 1/ 3Watts with electronic ballast / driver of approved design
and makes with lamps or Approved equivalent.Basic price Rs 3500/- Per Nos.
186 DIRECT/ INDIRECT LIGHT2X36WFTL EA 10
DARK LIGHTER 2 x 36W (300 x 300mm ): Recessed Two Tube dark lighter concealed fitting with 2 x 36
Watts, Tulips make or Approved equivalent.HF with electronic ballast of Philips / Tulips / Thorns make or
Approved equivalent.
187 SPOT LIGHT 5 / 8WATTS-75mm Dia EA 5
SPOT LIGHT 5 / 8 Watts: Recessed type spot light concealed fitting with 5 / 8Watts CFL, Tulip make /
Approved equivalent.HF with elctronic ballast of Philips / Tulips / Thorns makes or approved equivalent.
188 WALL/TABLE FAN EA 80
Providing and fixing of high speed tower fans of approved make and colour or Approved equivalent.
189 LED STRIPS / TUBES MR 40
Providing and fixing of LED strips / tubes, min. 4.2 Watt / met with drivers and 1nos. of driver to be
required for 10 meter with necessary fitting required for this items of approved makes and colour or
Approved equivalent.
LAN and TELEPHONE NETWORK
Supply, laying, connection (both end of cable RJ 45, socket or jack to crimping),testing and commissioning
of LAN system as given below. Cable to be laid through under floor trunking / 25mm PVC conduits pipe of
HMS / metal cable tray as directed by Architect or Engg in charge and payment will be made in the
respective items.
190 Cat6-E cable for Data/LAN MR 7000
Cat6-E cable for Data/LAN from information outlet upto hub / Rack.
191 Information outlet DUAL TYPE EA 100
Information outlets DUAL TYPE including termination with cat6-E cable (IOS) socket.
192 Information outlet SINGLE TYPE EA 6
Information outlets SINGLE TYPE including termination with cat. 6 wires.
193 Dual/Quad face plates EA 100
Supply, laying, connection and testing Dual / Quad face plate
194 Single face plate EA 10
Supply, laying, connection and testing single face plate
195 Blank inserts for faceplate EA 100
Supply, laying, connection and testing blank inserts for faceplates as required
196 Fibreoptic cable 4C indoor 50m MR 100
Supply, laying, connection and testing 4 core indoor,multimode 50 micron fibre optic cable of approved
make
Supply and Installation of following, for TELEPHONE NETWORK.
Rate quoted for the following items shall be including supply, laying, connecting, testing and
commissioning of telephone points with ferrule/ tag marking of telephone points to lay from DB (krone
connector) to receiver with appropriate size of unarmoured cable as per line diagram and specification with
all necessary fittings to be laid through under floor trunking/25mm PVC conduits pipe as directed by
Architect or Engg in charge, all complete and will be paid in the respective items.
197 Cat5-E telephone cable MR 3500
Cat5-E telephone cable from telephone outlet to telephone junction box.
198 20 pair,tele. cable-0.5sqmm MR 20
20 pair, telephone cable of 0.5 sqmm of approved make.
199 50 pair,tele. cable-0.5sqmm MR 20
50 pair, telephone cable of 0.5 sqmm of approved make.
200 100 pair,tele. cable-0.5sqmm MR 80
100 pair, telephone cable of 0.5 sqmm of approved make.
201 Dual I/O socket EA 100
Dual I/O socket to be mounted on provided monument box along with facepalte.
202 Single I/O socket EA 10
Single I/O socket to be mounted on partition/wall with concealed metal box along with faceplate.
Supply and installation of telephone junction box with GI enclosure of thickness of minimum 16 SWG:
203 Tele.JB 100 pair crone connect EA 1
Telephone Junction box with 100 pair crone connector
204 Tele.JB 50 pair crone connect EA 1
Telephone Junction box with 50 pair crone connector
Heavy gauge PVC conduits
Supply and laying of heavy gauge PVC conduits of HMS low halogen with required accessories for LAN /
telephone / computer / TV system in partition / above false ceiling as per site requirement.
205 20mm PVC conduit. MR 40
Page 104 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
206 25mm PVC conduit. MR 500
207 32mm PVC conduit. MR 50
PANEL BOARDS and CABLING WORK
Page 105 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
Supply, Installation, Testing and Commissioning of main Panel
Design, fabrication, assembling, wiring, supply, installation, testing & commissioning of Main distribution
boards/ sub distribution boards fabricated out of 14 gauge CRCA sheet steel in cubicle formation with
reinforcement of suitable size angle iron, channels, T irons, flats wherever necessary for large distribution
boards/panels, where as 16 gauge CRCA sheet steel for final distribution boards. The distribution board
have to moisture, dust & vermin proof and IP 42 degree of protection. Cable gland plates shall be provided
at "top & bottom" both.
The boards shall be treated with all anticorrosive process before painting as per standards with 2 coats of
red oxide primer & final approved shade of powder coating. 2 nos. earthing terminals shall be provided for
3 phase distribution boards. The boards shall be suitable for 415 V, 3 phase, 4 wire, 50 Hz supply system.
Lifting hooks shall be provided in case of large boards. Boards shall be fabricated in easily transportable
sections & length, height, depth etc to match with site conditions. An approval shall be taken for each
panel before final manufacture.
Galvanised hardwares with zinc passivation shall be used in fabrication of boards. Follow the detailed
specifications at the time of fabrication.
208 MAINPANEL-300/200/63A TPN MCCB EA 1
Incomer
500A TPn MCCB 35KA, with shunt trip-1SET
Bus : 500A TPN CU Tint Bus
Metering : Load Manager (3parameter display screen)- 1nos , LED Indicating lamps, CTS for APFC & other
requirement
Outgoings
300A TPn MCCB with ON indication, 25KA - 2 set
200A TPn MCCB with ON indication, 16KA - 1set
63A TPn MCCB with DIGITAL KWH METER & ON indication, 16KA - 3set
50/40/32A TPn MCB - 10set
32/25/20 A SP MCB - 6set
Surge suppressor- Clamping voltage - 400 Volt, minimum 600 Joules, response time-1micro second or
better, should have indicating light
209 100KVAR APFC PANEL EA 1
Incommer
200A TPMCCB 25KA - 1set
Metering :
12 Stage APFC intellegent Ralay & Indication LED lamps, should have display of power factor for each of the
3 phases
Outgoings
20KVAr Capacitor Bank , APP type with Current limiting Reactor, MCB , Capacitor duty Contactor - 1set
10KVAr Capacitor Bank , APP type with Current limiting Reactor, MCB , Capacitor duty Contactor - 5set
5KVAr Capacitor Bank , APP type with Current limiting Reactor, MCB , Capacitor duty Contactor - 6set
210 INVERT.INPUT32A DP MCB-MS ENC EA 1
INVERTER Inpur in MS Enclosure- 32A DP MCB, 10KA - 1set
211 INVERTER OUTPUT DB EA 1
Incomer -
40A DP MCB, 10KA - 1set
Bus : 100A 2P Cu Bus
OUTGOING :
25A DP MCB - 3 nos
212 80/63A FP MCCB-HVAC VRV UNIT EA 3
80/63A FP MCCB with 300 mA ELCB in Weather proof Box for HVAC VRV Out door units
213 10/16A,100mA,DP ELCB WITH ENCL EA 3
10/16A,100mA,DP ELCB WITH ENCLOSURE
DISTRIBUTION BOARDS
Supplying and fixing of following types of factory fabricated prewired SPN and TPN double door sheet steel
MCB distribution boards, moisture, dust and vermin proof having IP 42 degree of protection, 240/415 volts,
on surface/recess, complete with tinned copper busbar, neutral busbar equal to Phase busbar, earth bar,
din bar, interconnections, finished with powder coating including , earthing etc. as required :
214 LIGHTING DB (LDB)-12 W TPN DB EA 2
12 WAY TPN DB with the following:
Incomer
1 No.40A, FP MCB and 3 nos.40A/100 mA DP ELCBs each per phase with separate neutral & earth links per
phase, Neutral bus should be equal to Phase bus
Outgoings
24Nos.6A/10A SP MCB's
215 RAWPOWER DB 12 W TPN DB EA 2
12 WAY TPN DB with the following:
Incomer
Page 106 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
1 No.40A, FP MCB and 3 nos.40A/100 mA DP ELCBs each per phase with separate neutral & earth links per
phase, Neutral bus should be equal to Phase bus
Outgoings
24 Nos.6A/10A SP MCBs
Page 107 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
216 ACDB (IDU VRV) 8W TPN DB EA 2
8 WAY TPN DB with the following:
Incomer
1 No.32A, FP MCB and 3 nos.32A/100 mA DP ELCBs each per phase with separate neutral & earth links per
phase, Neutral bus should be equal to Phase bus
Outgoings
18Nos. 10A A SP MCB's
217 COMPUTER DB-Office Area (CPDB) EA 2
12 WAY TPN DB with the following:
Incomer
1 No.40A, FP MCB and 3 nos.40A/300 mA DP HPi each per phase with separate neutral & earth links per
phase, Neutral bus should be equal to Phase bus.
Outgoings
24Nos.6A/10A A SP MCB's
218 SPN DB (RPDB & ELDB) EA 2
SPN DB
Incomer 16A DPELCB - 1 No.
Outgoing 20/16/10A SP MCBs -4 Nos.
CABLING
Supply ,Laying, connection, testing and commissioning of PVC Armoured Copper / Aluminium conductor
cables 650 / 1100V with PVC insulated PVC sheathed steel armoured cable complete of FRLS industrial
cableup to 1100V in 25mm PVC conduits pipeof low halogen of following sizes including supports, clamps,
termination of cables with lugs and glands etc. Bare earth wire to be binded with cables and taken to the
same saddles / clamps of cable fixing all complete from main power supply to various panels along with
wall / ceiling as per the following specification for :-
219 4CX6sqmm Cu YFY+2 X 10SWG Cu MR 60
4 Core x 6 sq.mm Copper YFY + 2x10SWG Cu bare wire earthing.
220 4CX10sqmm Cu YFY +2X 10SWG Cu MR 50
4 Core x 10 sq.mm Copper YFY + 2x10SWG Cu bare wire earthing.
221 4CX16sqmm Cu YFY +2X 10SWG Cu MR 250
4 Core x 16 sq.mm Copper YFY + 2x10SWG Cu bare wire earthing.
222 4CX10sqmm AYFY+2X 10SWG Cu MR 60
4 Core x 10 sq.mm AYFY + 2x10SWG Cu bare wire earthing.
223 4CX16sqmm AYFY+2X 10SWG Cu MR 60
4 Core x 16 sq.mm AYFY + 2x10SWG Cu bare wire earthing.
224 3.5CX50 sqmm A2YFY cable MR 30
3.5 c x 50 sqmm A2YFY cable
225 3.5CX240 sqmm AL cable (A2YFY) MR 30
3.5 C X 240 sqmm aluminum cable (A2YFY) for the main source of power
226 3.5CX300 sqmm AL cable (A2YFY) MR 30
3.5 C X 300 sqmm aluminum cable (A2YFY) from 2nd floor to Main panel
227 4CX25sqmm Cu+2 No 4 sqmm green MR 10
4 Core x 25 sq.mm Copper + 2 No 4 sqmm green insulated wire for earthing.
228 2CX6qmm Cu+2 No 4 sqmm green MR 40
2 Core x 6 sq.mm Copper + 2 No 4 sqmm green insulated wire for earthing.
Cable Terminwith Cu Lug&Gland
Supply and Providing Cable Terminations with Copper Lugs and Glands :
229 Cable Term2/4CX6/10/16/25sqmm EA 24
Termination of 2/4 Core x 6/10/16 /25 sq.mm Cable
230 Cable Termination 3.5CX70 sqmm EA 2
Termination of 3.5 C x 70 sq.mm cable
231 Cable Termination 3.5CX240sqmm EA 4
Termination of 3.5 C X 240 sqmm cable
232 Cable Termination 3.5CX300sqmm EA 4
Termination of 3.5 C X 300 sqmm cable
233 Cu PVC earthwire 1CX6 sqmm MR 100
Supply and Laying of 1 core x 6 sq.mm Cu. PVC earth wire including all accesories and 25mm PVC condiuts
pipes.
234 Cu earthstrip25X3mmPVC insulat MR 60
Supply and Laying of 25x3mm PVC insulated Copper earth strip with all required acesssories and 25mm PVC
condiuts pipes.
UNDER FLOOR RACEWAYS and ACCESSORIES
Supply and installation, of under floor raceways and accessories including floor cutting, chiseling and
necessary Civil work as per approval of Architect/Consultant.
235 Al.raceway 100WX38mmDeep 16SWG MR 500
100mm wide, 38mm deep single Compartment, 16 SWG, Aluminium extruded section for under floor
raceways (rectangular shape).
Page 108 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
236 GI junc box 200X200X42mm14 SWG EA 50
200mm x 200mm x 42mm, 14 SWG G.I. Junction Box with S.S cover.
237 GI junc box 300X300X42mm14 SWG EA 30
300mm x 300mm x 42mm, 14 SWG G.I. Junction Box without S.S cover.
CABLE TRAY
Supply & installations of heavy gauge perforated Cable Tray made of GI sheet steel., min 1.6mm thick, with
sides not less than 50 mm deep, fittings are to be same material as tray, each coupling should have GI
earthing connector.Support shall be spaces not more than 1000mm apart & at all bends & couplings. the
rate shall be inclusive of all other required accessories, supports rods & plates etc.
238 150x50mm Perforated Cable tray MR 50
150x50mm Perforated type Cable tray
239 300x50mm Perf.Cable tray MR 50
300x50mm Perforated type Cable tray
240 450x50mm Perf.Cable tray MR 5
300x50mm Perforated type Cable tray
241 300x50mm Perf.Cable tray+cover MR 30
300x50mm Perforated type Cable tray with cover
242 MS FABRICATION KG 100
Ms Fabrication as required
PUBLIC ADDRESS and MUSIC SYSTEM
Supply, installation of the following acessories for Public Address & Music system complete by the
manufacturer along with installation guarantee for one year.Additional guarantee of various products shall
be passed on to HPCL for the BOSE as directed by HPCL.
243 Integration with existing sys LS 1
Integration of the public address system with the existing public address system installed at 1st & 4th
Floor, including supplying & installation of all the required equipments for the required integration.
244 Bose Freespace Model8 loud-6W EA 40
Bose Free Space Model 8 loudspeaker, 6w of bose makes or approved equivalent.
245 Bose 200 W Amplifier EA 1
Bose 200w Booster cum mixing Amplifier of bose make or approved equivalent.
246 Speaker cable-2 core 24/0.2 MR 450
Two core 24 / 0.2 speaker wires including suitable size PVC conduit concealed on wall/ceiling/wooden
partitioning, fixed with spacers, G.I. saddles etc. with bends, sockets, couplings, junction boxes etc. to
make piping rigid with chasing in wall as required all complete ready to be connected to the various
system/units as mentioned in this section of approved equivalent as per Architect / EIC.
247 Bose FreeSpace Syst.Controller EA 1
Bose Free Space System Controller of bose makes or approved equivalent.
248 AT 10 Volume Control EA 40
AT 10 Volume Control of approved equivalent as per Architect / EIC.
249 AT 35 Volume Control EA 4
AT 35 Volume Control of approved equivalent as per Architect / EIC.
250 AT 100 Volume Control EA 6
AT 100 Volume Control of approved equivalent as per Architect / EIC.
251 Shure-SL 550 Microphone EA 1
Shure make SL 550 Microphone with stands of approved equivalent as per Architect / EIC.
252 Denon DCM-280 MultiCD Changer EA 1
Denon DCM make 280 Multi CD Changer of approved equivalent as per Architect / EIC
253 19” Equipment Rack EA 1
19” Equipment Rack as per approved design to accommodate all the above Equipment of approved
equivalent as per Architect / EIC.
254 INST&COMM.-PUBLIC ADD SYSTEM EA 1
Installation and commissioning Charges for for the entire system by the manufacturer along with
installation guarantee for one year.Additional gurantee of various products shall be passed on to HPCL of
approved equivalent as per Architect / EIC.
EARTHING & MISCELLANEOUS ITEMS
255 Pipe type earth pit EA 2
Supply Installation Testing &commissioning of Pipe type earth pits with 80 mm dia, two meters length pipe
with specially developed on Pipe in pipe/Strip concept filled with highly conductive & anticorrosive
crystalline conductive mixture. The back fill is to be done by special compound which retains moisture &
enhance conductivity. The rate should be inclusive of making bore & finish & terminated in chamber,
masonry chamber with concrete base, manhole, lockable cover with frame (500 x 500 mm) For dedicated
Earth, make Ashlok or equivalent
Earthing cond./tape/flat strip
Supply/Installation/Testing/Commissioning of Earthing conductors/tape/flat strips
Page 109 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
256 GI Tape/Flat strip 50x6 mm MR 100
257 GI Tape/Flat strip 32x6 mm MR 50
258 GI Tape/Flat strip 25x3 mm MR 50
259 10 SWG Cu earth wire MR 200
Flex PVCinsulated Cu conductor
Supply & laying of single core flexible PVC insulated Copper conductor , from Earth Pit to UPS/Comm
equipment etc. The portion of the strip under-ground shall be laid to a depth of at least 60cms. The rates
shall include cost of all GI/HMS PVC pipe as per requirement & accessories. for outdoor GI & for indoor PVC
pipes to be used.
260 1 core 25sqmm Cu conductor MR 160
261 1 core 10sqmm Cu conductor MR 50
262 1 core 4 sqmm Cu conductor MR 200
1 core 4 sqmm. For equipotentail bonding in Server/HUB room & dedicated earth for CPDB
263 Cu earthbus 50x6X300 mm(WxBxL) EA 2
Supply,installation,testing & commissioning of copper Earth bus of various size mounted on insulators ,in
suitable size painted MS box. Bus should have 10 nos of holes with brass nut bolts of suitable size
264 Dismant& rem old Installation EA 1
Dismentalling & Removing of old installation carefully & handed over to HPCL
265 Temporary light/pow. arrangemt EA 1
Supply & making of temporary arrangement of sufficent lighting & power outlets during execution , exiting
items can be used for this arrangement
266 3KVA 1 ph. SW Online Inverter EA 1
Supply,installation,testing & commissioning of 3KVA single phase sine wave online inveter with 1 hour
backup battery bank, maintenace free lead acid battery of exide makes & interconnection leads of
Luminous / Megatech approved makes.
267 Rubber mat,1st aidchart,Box et LS 1
Supply & fixing of ISI marked 1.1KV Rubber mat Conforming to IS 15652:2006, fisrt aid chart, Fisrt aid Box,
safety Dos & Donts, Asbult laminated copy(after verification) of SLD & lighting, metal signages on each
breakers/ cable tags
ACCESS CONTROL SYSTEM
Supply, installation, testing & commsioning charges of the following complete acessories for Access control
system of apprved makes of GODREJ / SIEMENS / MORLEY / HID / SOLUS.
268 Proximity CardReader-range4cm EA 7
Proximity card Reader with read range of 4 cms of HID makes or approved equivalent as per Architect / EIC.
269 Door Controller EA 2
4 door (4 Reader) Controller TCP/IP networked with cabinet and battery backup, of Siemens / Solus makes
or approved equivalent as per Architect / EIC.
270 Electromagnetic Door Lock EA 6
Electromagnetic Door Lock of Dafikas makes or approved equivalent as per Architect / EIC.
271 Egress Emergency Exit switch EA 3
Egress Emergency Exit switch of approved equivalent as per Architect / EIC.
272 Time Management Software EA 1
Time Management Software of Siemens makes or approved equivalent as per Architect / EIC.
273 Time&attendance software EA 1
Time and attendance software (Optional) of Siemens makes or approved equivalent as per Architect / EIC.
274 Wiegand Converter EA 3
Wiegand Converter of approved make or equivalent as per Architect / EIC.
275 PC interface card EA 1
PC interface card of Siemens makes or approved equivalent as per Architect / EIC.
276 Proximity card plain EA 100
Proximity card plain of HID makes or approved equivalent as per Architect / EIC.
277 Battery EA 1
Battery of approved equivalent as per Architect / EIC.
278 8CX1.0 sqmm Copper Flex Cable MR 200
8 core 1.0 sq.mm Shielded, PVC Sheathed Copper Flexible Cable of RR / Sigma / Komet or approved
equivalent as per Architect / EIC.
Page 110 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
279 2CX1.0 sqmm Copper Cable MR 200
2 core 1.0 sq.mm Copper PVC Sheathed Cable in PVC Conduits with all accessories of RR / Sigma / Komet or
approved equivalent as per Architect / EIC.
280 Cat-5-E cable MR 100
Supply & Installaion of Cat-5 cable with PVC Conduit / truncking of approved make or equivalent as per
Architect / EIC.
281 Doorrelease manual pushbutton EA 1
Door release manual push button at Reception of HID makes or approved equivalent as per Architect / EIC.
CLOSED CIRCUIT TELEVISION SYST
Supply, installation, testing & commsioning charges of the following complete acessories for Closed circuit
television system of approved make.
282 IP D/N,Domecamera,1/3"SuperHAD EA 8
Supply, Installation, Testing & Commsissioning of IP, box / dome camera, for indoor Day / Night, 1/3" Super
HAD, Picture element 1600 (H) X 1200 (V) Pixel, 3-9 mm varifocal F 1.2 - 2 Megapixel, 0 Lux & F1.2 (IR Cut
filter removed, with external IR illumination).
283 CISCO 12 port PoE switch EA 1
Supply and installations CISCO catalyst 3560 compact 12 10/100 PoE switches model no. WS-C3560-12PC-S.
Warranty: Comprehensive on-site warranty for a period of 36 months from the date of final
configuration/installation of switches
Page 111 Seal Signature of Tenderer
S N DESCRIPTION UNIT QTY
284 UTP,4 pair CAT-6-E LAN cable MR 750
Supply and Installation of UTP, 4 pair CAT - 6-E LAN cable with PVC trunking / PVC Conduit as instructed by
Architect / EIC
FIRE ALARM SYSTEM
Supply, installation, testing & commsioning of the following complete acessories for Fire alarm system of
approved make
285 Analg.Main fire alarm panel EA 1
Supply & Installation Testing ,commissioning of , Standalone Analogue Addressable Main Fire Alarm ,
Power supply & battery backup complete as per following features:
1 loop or suitable for below devices
(1 Loop - 100 + 100 ( Detectors + Devices))
Large LCD display minimum 2 x 80 Character
Shall integrate Control,Monitor,Relay modules,Dust, Smoke, Heat ,Beam ,Flame detectors.
Battery of 48 hrs backup in normal condition,+ 1 hr backup with 25% Loop under fire condition.
CE/LPCB APPROVED
Supply of signal initiating devices complete with galvanised steel, back box, detector, base detector etc.
complete as specified and as required.
286 OPTICAL smoke detector EA 65
Addressable type Optical Smoke detector with sensitivity of 0.5% to 2.35% per foot with base & MS powder
coated junction box of Siemens makes or approved equivalent as per Architect / EIC.
287 Addressable Heat detector EA 5
Addressable Intelligent Heat detector with base ( RHSE ) of siemens makes or approved equivalent as per
Architect / EIC.
288 Manual Callpoint EA 2
Addressable Manual call point with break glass unit ( MCP-GB ) of Siemens makes or approved equivalent
makes as per Architect / EIC.
289 Fault Isolator Module EA 2
Addressable Fault isolator module in suitable ABS plastic glossy box of Siemens makes or approved
equivalent as per Architect / EIC.
290 Loop Powered Sounder EA 2
Addressable Loop powered sounder ( LASR ) of Siemens makes or approved equivalent as per Architect /
EIC.
291 Control/Relay Module EA 3
Addressable Control / Relay output module ( CM ) in suitable ABS plastic glossy box of Siemens makes or
approved equivalent as per Architect / EIC.
292 Remote response indicator EA 12
Remote response indicator having twin LED flush mounted on false ceiling / wall as per approved
equivalent makes.
293 Monitor Module EA 3
Addressable monitor output module ( CM ) in suitable ABS plastic glossy box of Siemens makes or
approved equivalent as per Architect / EIC.
294 2CX1.5 Sqmm armoured Cu cable MR 1000
Supply & laying of 2core x 1.5 mm2, PVC insulated copper conductor Shielded Armoured Cable of Sigma /
RR / Komet or approved equivalent as per Architect / EIC.
Makes: Morely, System sensor, Siemens
295 Analog Energy meter EA 1
Supplying, installation, Testing and Commissioning of analog energy meter
296 Analog Volt meter EA 1
Supplying, installation, Testing and Commissioning of analog voltmeter; rating 0-500 Volts
297 Analog Ammeter EA 1
Supplying, installation, Testing and Commissioning of analog energy meter; rating 0-500 Amp
Page 112 Seal Signature of Tenderer