10416 Polyurethane 750ml AW - Woodcare Direct Tough Clear_Varnish2.pdf · provides long lasting...
-
Upload
truongdung -
Category
Documents
-
view
215 -
download
0
Transcript of 10416 Polyurethane 750ml AW - Woodcare Direct Tough Clear_Varnish2.pdf · provides long lasting...
10416_Polyurethane_750ml_AW 19/4/12 10:48 Page 1
Ronseal Ultra Tough VarnishFlammable. Repeated exposure may cause skin drynessor cracking. Keep out of the reach of children. Keepaway from sources of ignition – No smoking. Avoidcontact with skin and eyes. In case of contact witheyes, rinse immediately with plenty of water andseek medical advice. After contact with skin, washimmediately with plenty of water. Wear suitable gloves.If swallowed, seek medical advice immediately andshow this container or label. Use only in well-ventilatedareas. Dispose of this material and its container to ahazardous or special waste collection point. ContainsCobalt 2-Ethylhexanoate, ETHYL METHYL KETOXIME.May produce an allergic reaction.
ULTRA TOUGH
TOUGH POLYURETHANE GLOSS VARNISHFOR INTERIOR WOOD
HARDGLAZEHARDGLAZEEU limit value for this product (cat. A/e): 500g/l (2007) / 400g/l (2010).This product contains max 500g/l VOC
Ronseal Ultra Tough HardglazeRonseal Ultra Tough Hardglaze is a superiorpolyurethane gloss varnish which protects interiorwood whilst adding depth to the beauty of thewood grain. The polyurethane - alkyd formulationprovides long lasting protection against knocksand scratches and resists most householdchemical spillages including boiling water andalcohol. The high content of polyurethane in thevarnish ensures quicker hardness and abrasionbuild up than other solvent based varnishes. Theextended working time eliminates lap marks todeliver a rich, clear, mellow finish that enhancesthe beauty of the wood.
PreparationEnsure all surfaces are free from wax, greaseand oil by wiping with a cloth dampened withwhite spirit. Barewood: Sand smooth with finesandpaper. Remove dust with a cloth dampenedwith white spirit. Varnished wood: Removeunsound varnish. Sand well to a uniformappearance and clean with white spirit. Allowto dry thoroughly. Avoid inhaling dust whensanding by wearing a suitable face mask.
ApplicationStir well before and during use. Apply in a warm,well-ventilated room. Using a brush, apply 2 or 3coats. Brush out evenly and finish each coat inthe direction of the grain. Leave 4 hours betweencoats. Before final coat, lightly rub down usingfine sandpaper and wipe with white spirit.
Clean UpClean brushes with white spirit or paint brushcleaner. Remove as much varnish as possiblefrom the brush before cleaning. Some localauthorities have special facilities for disposingof waste coatings. Do not empty into drainsor watercourses.
ImportantDo not use on plastic type materials. Certaintropical woods may prolong drying timesor cause poor adhesion. Always teston a small area first. Polyurethanevarnishes may darken the colourof bare wood & dyed wood.Special precautions shouldbe taken during surfacepreparations of pre-1960s paintsurfaces over wood and metalas they contain harmful lead.Drying times may be extendedwhen using over Colron WoodDye. To avoid risk of spillage,always store and transport in asecure and upright position. For a waterclear finish use Ronseal Quick DryingClear Varnish. For use only as directed.
FOR FURTHER ADVICE, PLEASE CONTACT:RONSEAL TECHNICAL SERVICES, Tel: 0114 240 9469
Ronseal Ltd, Thorncliffe Park, Chapeltown, Sheffield, S35 2YP.Telephone: 0114 246 7171 Fax: 0114 246 5629
Email: [email protected] www.ronseal.co.uk750mlMade in Great Britain. Ronseal & Ronseal Does Exactly WhatIt Says On The Tin are registered trademarks of the Sherwin-Williams Company. © Ronseal 2007
501
0214
5669
38
Usage Areas Any bare or previously treated interior wood including doors, furniture, shelving, skirting boards, cork, hardboard or chipboard.
Compatability Suitable for use on bare wood or over existing solvent based finishes such as varnish or wood dye.
Finish Rich, gloss sheen.Number of coats 2 for treated wood, 3 for untreated wood.Coverage Up to 10 square metres per litre. 750ml will
be sufficient to treat 4 door sides with 2 coats(approx 7.5 sq m).
Dry Times Touch dry in 2 hours. Recoat in 4 hours.Clean Up Clean brushes with white spirit or paint brush cleaner.
10416_Polyurethane_750ml_AW 19/4/12 10:48 Page 2
Ronseal Ultra Tough VarnishFlammable. Repeated exposure may cause skin drynessor cracking. Keep out of the reach of children. Keepaway from sources of ignition – No smoking. Avoidcontact with skin and eyes. In case of contact witheyes, rinse immediately with plenty of water andseek medical advice. After contact with skin, washimmediately with plenty of water. Wear suitable gloves.If swallowed, seek medical advice immediately andshow this container or label. Use only in well-ventilatedareas. Dispose of this material and its container to ahazardous or special waste collection point. ContainsCobalt 2-Ethylhexanoate, ETHYL METHYL KETOXIME.May produce an allergic reaction.
ULTRA TOUGH
TOUGH POLYURETHANE MATT VARNISHFOR INTERIOR WOOD
MATTCOATMATTCOATEU limit value for this product (cat. A/e): 500g/l (2007) / 400g/l (2010).This product contains max 500g/l VOC
Ronseal Ultra Tough MattcoatRonseal Ultra Tough Mattcoat is a superiorpolyurethane matt varnish which protects interiorwood whilst adding depth to the beauty of thewood grain. The polyurethane - alkyd formulationprovides long lasting protection against knocksand scratches and resists most householdchemical spillages including boiling water andalcohol. The high content of polyurethane in thevarnish ensures quicker hardness and abrasionbuild up than other solvent based varnishes. Theextended working time eliminates lap marks todeliver a rich, clear, mellow finish that enhancesthe beauty of the wood.
PreparationEnsure all surfaces are free from wax, greaseand oil by wiping with a cloth dampened withwhite spirit. Barewood: Sand smooth with finesandpaper. Remove dust with a cloth dampenedwith white spirit. Varnished wood: Removeunsound varnish. Sand well to a uniformappearance and clean with white spirit. Allowto dry thoroughly. Avoid inhaling dust whensanding by wearing a suitable face mask.
ApplicationStir well before and during use. Apply in a warm,well-ventilated room. Using a brush, apply 2 or 3coats. Brush out evenly and finish each coat inthe direction of the grain. Leave 4 hours betweencoats. Before final coat, lightly rub down usingfine sandpaper and wipe with white spirit.
Clean UpClean brushes with white spirit or paint brushcleaner. Remove as much varnish as possiblefrom the brush before cleaning. Some localauthorities have special facilities for disposingof waste coatings. Do not empty into drainsor watercourses.
ImportantDo not use on plastic type materials. Certaintropical woods may prolong drying timesor cause poor adhesion. Always teston a small area first. Polyurethanevarnishes may darken the colourof bare wood & dyed wood.Special precautions shouldbe taken during surfacepreparations of pre-1960s paintsurfaces over wood and metalas they contain harmful lead.Drying times may be extendedwhen using over Colron WoodDye. To avoid risk of spillage,always store and transport in asecure and upright position. For a waterclear finish use Ronseal Quick DryingClear Varnish. For use only as directed.
FOR FURTHER ADVICE, PLEASE CONTACT:RONSEAL TECHNICAL SERVICES, Tel: 0114 240 9469
Ronseal Ltd, Thorncliffe Park, Chapeltown, Sheffield, S35 2YP.Telephone: 0114 246 7171 Fax: 0114 246 5629
Email: [email protected] www.ronseal.co.uk750mlMade in Great Britain. Ronseal & Ronseal Does Exactly WhatIt Says On The Tin are registered trademarks of the Sherwin-Williams Company. © Ronseal 2007
501
0214
5669
52
Usage Areas Any bare or previously treated interior wood including doors, furniture, shelving, skirting boards, cork, hardboard or chipboard.
Compatability Suitable for use on bare wood or over existing solvent based finishes such as varnish or wood dye.
Finish Rich, matt sheen.Number of coats 2 for treated wood, 3 for untreated wood.Coverage Up to 10 square metres per litre. 750ml will
be sufficient to treat 4 door sides with 2 coats(approx 7.5 sq m).
Dry Times Touch dry in 2 hours. Recoat in 4 hours.Clean Up Clean brushes with white spirit or paint brush cleaner.
10416_Polyurethane_750ml_AW 19/4/12 10:48 Page 3
ULTRA TOUGH
TOUGH POLYURETHANE SATIN VARNISHFOR INTERIOR WOOD
SATINCOATSATINCOATRonseal Ultra Tough VarnishFlammable. Repeated exposure may cause skin drynessor cracking. Keep out of the reach of children. Keepaway from sources of ignition – No smoking. Avoidcontact with skin and eyes. In case of contact witheyes, rinse immediately with plenty of water andseek medical advice. After contact with skin, washimmediately with plenty of water. Wear suitable gloves.If swallowed, seek medical advice immediately andshow this container or label. Use only in well-ventilatedareas. Dispose of this material and its container to ahazardous or special waste collection point. ContainsCobalt 2-Ethylhexanoate, ETHYL METHYL KETOXIME.May produce an allergic reaction.
EU limit value for this product (cat. A/e): 500g/l (2007) / 400g/l (2010).This product contains max 500g/l VOC
Ronseal Ultra Tough SatincoatRonseal Ultra Tough Satincoat is a superiorpolyurethane satin varnish which protects interiorwood whilst adding depth to the beauty of thewood grain. The polyurethane - alkyd formulationprovides long lasting protection against knocksand scratches and resists most householdchemical spillages including boiling water andalcohol. The high content of polyurethane in thevarnish ensures quicker hardness and abrasionbuild up than other solvent based varnishes. Theextended working time eliminates lap marks todeliver a rich, clear, mellow finish that enhancesthe beauty of the wood.
PreparationEnsure all surfaces are free from wax, greaseand oil by wiping with a cloth dampened withwhite spirit. Barewood: Sand smooth with finesandpaper. Remove dust with a cloth dampenedwith white spirit. Varnished wood: Removeunsound varnish. Sand well to a uniformappearance and clean with white spirit. Allowto dry thoroughly. Avoid inhaling dust whensanding by wearing a suitable face mask.
ApplicationStir well before and during use. Apply in a warm,well-ventilated room. Using a brush, apply 2 or 3coats. Brush out evenly and finish each coat inthe direction of the grain. Leave 4 hours betweencoats. Before final coat, lightly rub down usingfine sandpaper and wipe with white spirit.
Clean UpClean brushes with white spirit or paint brushcleaner. Remove as much varnish as possiblefrom the brush before cleaning. Some localauthorities have special facilities for disposingof waste coatings. Do not empty into drainsor watercourses.
ImportantDo not use on plastic type materials. Certaintropical woods may prolong drying timesor cause poor adhesion. Always teston a small area first. Polyurethanevarnishes may darken the colourof bare wood & dyed wood.Special precautions shouldbe taken during surfacepreparations of pre-1960s paintsurfaces over wood and metalas they contain harmful lead.Drying times may be extendedwhen using over Colron WoodDye. To avoid risk of spillage,always store and transport in asecure and upright position. For a waterclear finish use Ronseal Quick DryingClear Varnish. For use only as directed.
FOR FURTHER ADVICE, PLEASE CONTACT:RONSEAL TECHNICAL SERVICES, Tel: 0114 240 9469
Ronseal Ltd, Thorncliffe Park, Chapeltown, Sheffield, S35 2YP.Telephone: 0114 246 7171 Fax: 0114 246 5629
Email: [email protected] www.ronseal.co.uk750mlMade in Great Britain. Ronseal & Ronseal Does Exactly WhatIt Says On The Tin are registered trademarks of the Sherwin-Williams Company. © Ronseal 2007
501
0214
5669
45
Usage Areas Any bare or previously treated interior wood including doors, furniture, shelving, skirting boards, cork, hardboard or chipboard.
Compatability Suitable for use on bare wood or over existing solvent based finishes such as varnish or wood dye.
Finish Rich, satin sheen.Number of coats 2 for treated wood, 3 for untreated wood.Coverage Up to 10 square metres per litre. 750ml will
be sufficient to treat 4 door sides with 2 coats(approx 7.5 sq m).
Dry Times Touch dry in 2 hours. Recoat in 4 hours.Clean Up Clean brushes with white spirit or paint brush cleaner.