10 x 12 Led & Al Roof Top With Netting -...
Transcript of 10 x 12 Led & Al Roof Top With Netting -...
1
Date of purchase: _____/ _____/ _____
Product Code: D71 M03457
UPC Code: 749241314148
10 x 12 Led & Al Roof Top With Netting
2
SAFETY INFORMATIONPlease read and understand this entire manual before attempting to assemble, operate orinstall the product. If any parts is missing or damaged, do not attempt to assemble the product.
Two to four people are needed for assembly.Load of the hook on the roof: 50 lbs. (max)In order to avoid damage to the shelter and its components, use appropriate tools. Check all screws on a regular basis to maintain the solidity of the structure.Keep instructions and parts list for further use.Estimated Assembly Time: Approx. 2 - 4 hoursTools required for Assembly (not included): Ladder, 5 ft. (at least 5 ft. during assembly).Snow load capacity - can hold up to 700LBS (max).
WARNINGKEEP ALL FLAME AND HEAT SOURCES AWAY FROM TENT FABRIC.This tent meets the flammability requirements of CPAI-84. The fabric may burn if left incontinuous contact with any flame source. The application of any foreign substance to thetent fabric may render the flame-resistant properties ineffective.
CAUTIONDo not leave outside during high winds, heavy rains or snow. The mosquito nets must be removed for winter storage.
WARRANTY1 year limited warranty.Limited warranty applicable on parts only. Warranty extends solely to the original purchaser, whomust offer the original sales receipt for record.
EXCLUDEDDamages due to vandalism, abuse and wrong use of the product is not covered by the warranty.Damages due to extreme weather conditions such as thunderstorm and windstorm.
MAINTENANCEDO NOT RETURN THE PRODUCT TO SEARS.If this gazebo needs repairs or replacement please contact Bond Vast directly at 1-800-961-9838,9AM ~ 5PM, Pacific Time Zone, Monday - Friday or email us: [email protected] email us: [email protected].
3
4
Item Description IllustrationQty
1
1
111
326622
4644
Post 1Post 2Post 3
Base flangeBase cap
Long crossbar 1
Long crossbar 2
Short crossbar 1
Short crossbar 2
Short crossbar 3
Short crossbar 4
Center connector
Tip connectorLong supporter
Short supporter
ABCDEFGHIJKLMNO
5
Item Description IllustrationQty2
123416444122412
PQRSTUVWXYZ
ABACADAE
Connector tube
Plastic cap
Connect wire 1
Connect wire 2
Roof connector 1
Roof connector 2
Roof cap
Short roof tube
Corner connector
Long roof tube
Air vent tube
Air vent panel 1
Air vent panel 2
Air vent corner connector
Roof tube 1
6
DescriptionItem Qty Illustration44
44
4444444
4
2
2
2
Roof tube 2Roof tube 3Roof tube 4Roof tube 5Roof tube 6Roof tube 7Roof tube 8Roof tube 9Roof panel 1Roof panel 2Roof panel 3Roof panel 4Roof panel 5Eave tube 1Eave tube 2
AFAGAHAIAJAKALAMANAOAPAQARASAT
DescriptionItem Qty Illustration4
411
6Eave tube 3Center protector
Corner protector
Mosquito netAC adapter
AUAVAWAXAY
1082020241
Qty IllustrationDescriptionItem
Screw 3
Screw 1Screw 2
StakeAllen wrench
AABBCCDDEE
7
8
A
B
C
x 1
x 3
x 2
x 6
x 6
D
E
B
E
D
E
B
AAAA
D
1
1
1. Insert base cap (E) into post (B), then using screw (AA) secure base flange (D) on the bottom of post (B).Repeat the step for all rest posts (A, B, C).
9
F
G
Mx 2
x 2
x 4
FM M G
F
M
F
AA
G
AA
AA
12
1. Insert long crossbar 1 (F) into long crossbar 2 (G) and secure with screw 1 (AA). Then secure tip connector (M) onto the long crossbar 1 (F) and long crossbar 2 (G) by using screw 1 (AA) as figure shown.Repeat this step for remaining long crossbar 1 (F) and long crossbar 2 (G).
2
2
21
H
I
M
L
x 1
x 1
x 1
x 1
H
L
M
I
H
L
M
I
AA AA
AA
1
1
1. Insert short crossbar 1 (H) into short crossbar 2 (I), then secure center connector (L) and tip connector (M) on short crossbar set (H, I) by using screw 1 (AA) as the figure shown.
10
J
K
M
L
x 1
x 1
x 1
x 1
J
M
LK
1
AA AA
AA
J
LK
M
1
1. Insert short crossbar 3 (J) into short crossbar 4 (K), then secure center connector (L) and tip connector (M) on the short crossbar set (J, K) by using screw 1 (AA) as the figure shown.Notes: Please check above fig. carefully and make sure all the parts in right position.
11
L x 1
G
L F
1
12
A C
B
AA
L
F
BB
C
BB
G
G
12
1. Secure long crossbar set (G, F) on the post 1 (A) and post 2 (B) by using screw 2 (BB), then secure the long crossbar set (G, F) on post 3 (C) by using screw 2 (BB) as figure shown. 2. Then secure center connector (L) on the long crossbar set (G, F) by using screw 1 (AA) as shown.Notes: Please check above fig. carefully and make sure all the parts in right position.
12
A
L x 1
B C
B
G
L F
B
G
G
BB
B
BB
L
F
AA
1
12
12
1. Secure long crossbar set (G, F) on the post 2 (B) by using screw 2 (BB), then secure the long crossbar set (G, F) on post 3 (C) by using screw 2 (BB) as figure shown. 2. Then secure center connector (L) on the long crossbar set (G, F) by using screw 1 (AA) as shown.Notes: Please check above fig. carefully and make sure all the parts in right position.
You need 3 persons for this step.
13
BB
H
1
B
BC
B
A
CB
J
K1
1
11
IH
You need 3 persons for this step.
1. Secure the short crossbar set (H, I) on the post 2 (B) by using screw 2 (BB) as shown.2. Secure the short crossbar set (J, K) on the post 1 (A) and post 2 (B) by using screw 2 (BB) as shown.Notes: Please check above fig. carefully and make sure all the parts in right position.
14
15
N Qx 4 x 8
GCC N
B
Q
N CC
GF
B
B
C
N
A
CB
N
FGN
N
12
1
2
1. Secure long supporter (N) under long crossbar (F) by using screw 3 (CC) as figure shown. Then secure both end section of long supporter (N) between corner post (B) and center post (C) by using screw 3 (CC), and cover it with plastic cap (Q) as figure shown.Repeat this step for remaining 3 long supporters (N).
O
PQ
x 4
x 2x 4
J
B
O
OP
CC Q
CC
I J
K
B
A
CB
C
B
O
OP
H
12
12
1. Insert short supporter (O) into connector tube (P), then insert screw 3 (CC) through connector tube (P) and short supporter (O) into the short crossbar 2 (I), then secure the end section of short supporter (O) onto post 2 (B) by using screw 3 (CC) and cover the plastic cap (Q).Repeat the step for remaining short supporter (O) and connector tube (P).
16
17
R x 3
HI
G J
KF
B R
FG J
K
H
B
AC
AR
GF
I
CB
B
1. Insert connector wire 1 (R) between long crossbar 2 (G) and post 1 (A), then insert connector wire 1 (R) between long crossbar 1 (F) between post 2 (B) as figure shown.2. Insert connector wire 1 (R) between short crossbar 1 (H) and short crossbar 2 (I) as shown.
3
1 2
1
3
2
18
S x 4
G
S
B
F G
S
FG J
K
I
C
H
B A
H
C
FG
BBC
12
12
2
1
1. Insert connect wire 2 (S) between long crossbar 1 (F), long crossbar 2 (G) and post 3 (C) as shown.2. Insert connect wire 2 (S) between long crossbar 2 (G), short crossbar 1 (H) and post 2 (B) as shown.Repeat for remaining 2 connect wire 2 (S).
19
T
U
x 1
x 6
1
1
2
2
2
2
2
U
AAU
T
U
U
M
AA
1. Insert screw 1 (AA) through roof connector 1 (T) underneath, secure with short roof tube (U) as figure 1 shown. Then insert screw 1 (AA) through tip connector (M), secure with the end section of roof tube (U) as figure 2 shown. Repeat for the remaining 5 roof tubes (U).
20
V
W
x 4
x 4
W
V
1
1
W
V AA
1. Secure corner connector (V) onto long roof tube (W) by using screw 1 (AA).Repeat for all remaining corner connector (V) and long roof tube (W).
21
T
AA
W
1
1
W W
AAAA
T
T
V2
2
2
2
1. Insert screw 1 (AA) through roof connector 1 (T) underneath, secure with long roof tube (W). Then insert screw 1 (AA) through corner connector (V), attached with both corssbar set as figure 2 shown.Repeat for remaining 3 long roof tubes (W).
22
X
Y
x 4
x 1
AAAA
X
Y
W
X Y
Y
X
AA
W W
W
1
1
22
1. Insert screw 1 (AA) through roof connector 2 (Y), and secure with air vent tube (X) as figure 1 shown. Then secure the end section of air vent tube (X) onto long roof tube (W) by using screw 1 (AA).Repeat for remaining air vent tube (X).
23
AD x 1
AD
AA
AA
Y
AD YX
1. Insert screw 1 (AA) through roof connector 2 (Y) and secure with roof cap (AD).
24
Z
AB AC
x 2
x 2 x 4
X
AC
ZX
AB
AAADX
ACZ2
2
11
AB
Z
1. Insert air vent panel 1 (Z) into air vent tube (X), then insert air vent panel 2 into other side of air vent tube (X) as figure 1 shown. Then secure air vent corner connector (AC) onto air vent tube (X) as figure 2 shown.Repeat for remaining air vent panel 1 (Z), air vent panel 2 (AB) and 2-tier corner connector (AC).
AB
25
AE
AF
AG
AH
AI
AJ
x 2
x 4x 4
x 2
x 4x 4
W U W
AJ
AIAJ
AHAI
AG
AF
AGAE AF
12
AE
AF
U
U
AA
AEU
AG
AA
1 2
1. Insert screw 1 (AA) through roof tube 3 (AG) and roof tube 1 (AE), and secure with short roof tube (U) as figure 1 shown. Then secure the end section of roof tube 1 (AE) and roof tube 2 (AF) with short roof tube (U) as figure 2 shown.Repeat for remaining roof tube (AE, AF, AG, AH, AI, AJ).
26
AN
AQ
AL
AO
AR
AP
AK
AM
x 4
x 4
x 4
x 4
x 4
x 4
x 4
x 2
AQ
AL
AR
AR
ALAQ
AN AK
AOAM
AP
AN
AQ
AL
AR
U
W
1. Insert roof panel 4 (AQ) into short roof tube (U) and long roof tube (W), and insert roof tube 8 (AL), then insert roof panel 5 (AR) into short roof tube (U) and long roof tube (W) as figure shown.Repeat the step for remaining roof panels (AN, AQ, AO, AR, AP).Caution: Follow the directions of the panel as shown in the diagrams to ensure proper piping. Please do not let the panels slide off.
27
AS
AT
AU
AV
AW
x 2
x 4
x 4
x 6
x 4
AT
AU
AU
AW
AA
AW
ASAV
AA
AT
AU
AUAV AS AT
1
2
12
1
2212
1. Insert screw 1 (AA) through corner protector (AW) and eave tube 2 (AT) and eave tube 3 (AU) into long roof tube (W).2. Insert screw 1 (AA) through center protector (AV) and eave tube 1 (AS) and eave tube 3 (AU) into short roof tube (U).Repeat for remaining eave tube (AS, AT, AU) and corner protector (AW), center protector (AV).
W U
28
AX
AY
x 1
x 1
B
B
B
A
C
A
FF
E
D
AY
AX
OUTLETON/OFF SWITCH
1. Hang the mosquito net (AX) by hooks properly.2. Raise base cap (E) and secure stakes (FF) through base flange (D) into the ground.3. Please ensure all the wires are connected properly then connect AC adapter (AY) on the
bottom of post (A) in clockwise. 4. Remove all gazebo assembly stickers.
29
USER MAINTENANCE INSTRUCTIONS
In preparation for winter storage, remove leaves and dirt, dray and wrap inpolybag to prevent rusting.Store in dry place.Treat aluminum frame periodically with liquid wax for maximum protectionagainst UV rays and moisture.Poly nettings clean with a soft brush and lukewarm water, rinse thoroughly.Dray completely.Do not wash with soap as it may remove the protective coating added by thefactory.
See our extensive assortment of outdoor living productson-line at www.sears.com and www.kmart.com
Made in / Hecho en CHINADistributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179
sears.com
For questions or comments about product:Email: [email protected] or Call toll-free: 1-800-961-9838
Please refer to part numbers when reordering
Bond Vast Industrial LimitedBao Tang Industrial Jing LianChiao Tou Town Dong Guang CityGuang Dong ProvinceChina 523538
Special Care Sheet:
Do NOT use the AC adapter during precipitation or inclement weather.Do NOT leave the AC adapter outside, place and store in dry place.Keep the AC adapter away from babies and children.In order to protect the LED lights, do NOT break the Acryl panel of the post.All lighting equipment is designed to prevent humidity and moisture, please do notdisassemble.When NOT using period of time, please turn off the power switch and unplug theAC adapter.Please connect all cables securely before plugging in power cable into power outlet.All the parts are special design for this product only, changes or modifications notapproved by the party responsible for compliance could void the user’s authorityto operate the equipment. The manufacture will not be held liable for any direct,indirect, incidental or consequential damages. Some states do not allow limitationson how long an implied warranty lasts, or the exclusion or limitation of incidental orconsequential damages, so the above limitations may not apply to you.