10’ X 10’ CANOpy - Harbor Freight...

10’ X 10’ CANOpyModel 97173

Set up ANd OperAtiNg iNStruCtiONS

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

distributed exclusively by Harbor Freight tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

read this material before using this product. Failure to do so can result in serious injury. SAVe tHiS MANuAl.

Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 97173 For technical questions, please call 1-800-444-3353.

SAVe tHiS MANuAlKeep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

iMpOrtANt SAFety iNFOrMAtiONin this manual, on the labeling, and all other information provided with this product:

this is the safety alert symbol. it is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

dANger indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WArNiNg indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAutiON, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOtiCe is used to address practices not related to personal injury.

CAutiON, without the safety alert symbol, is used to address practices not related to personal injury.

dANgerdANger

WArNiNgWArNiNg

CAutiONCAutiON

NoticeNotice

CAutiONCAutiON


WArNiNg! read all instructions Failure to follow all instructions listed below may result in serious injury.

SAVE THESE INSTRUCTIONS

WOrk AreA SAFetykeep children and bystanders away while assembling. distractions can cause you to lose control.

Keep setup area clean and well lit. Cluttered or dark areas invite accidents.

perSONAl SAFetyWear ANSi-approved safety goggles and heavy-duty work gloves during Canopy setup. Hands and fingers can be pinched in moving parts.

Stay alert and use common sense during use. Do not use when tired or under the influence of drugs, alcohol or medication.

Do not overreach during setup. Keep proper footing and balance at all times.

For temporary use only. Do use Canopy as permanent shelter.

Do not setup or use in rain, severe winds or during thunderstorms.

Do not allow any debris to pile up on Canopy.

Do not setup on steep surfaces; use only on flat, level surface able to support weight of canopy and materials and/or people placed under it.

Do not setup or use near heat or flames, such as barbecues or campfires.

Do not modify Canopy or use it for a purpose for which it is not intended.

The Canopy is not a toy. Keep it out of reach of children.

prOduCt uSe ANd CAreTwo people are needed to properly setup the Canopy.

Do not fold and/or store Canopy when it is damp or wet. Let dry to avoid mildew.

When washing, use only mild soap and warm water. Do not machine wash

Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the Canopy’s operation. If damaged, have the Canopy repaired before use.

1.

2.

1.

2.

3.

4.

5.

6.

7.

�.

9.

10.

1.

2.

3.

4.


Use the Canopy and any accessories etc., in accordance with these instructions and in the manner intended for the particular type of product, taking into account the working conditions and the work to be performed. Use of the product for op-erations different from those intended could result in a hazardous situation.

SerViCeHave product serviced by a qualified repair person using only identical replace-ment parts. This will ensure that the safety of the product is maintained.

Maintain labels and nameplates on the product. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replace-ment. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAVe tHeSe iNStruCtiONS.

5.

1.

2.

SpeCiFiCAtiONS

Assembled Height 7’-6” 5’-6” (Frame Clearance)

Canopy Clearance 65” Canopy Material PolyesterWeight 26 lb.

uNpACkiNgWhen unpacking, check to make sure that the item is intact and undamaged. If

any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.


Set up iNStruCtiONSread the eNtire iMpOrtANt SAFety iNFOrMAtiON section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

Opening the CanopyPlace the Canopy (1) in center of the area where you will set it up. Make sure it is on a flat and level surface able to support the weight of the Canopy.

Remove the Canopy (1) from the Carrying Bag (2) and stand the folded Canopy on its feet.

With the help of another person, grasp opposite outer legs and gently pull the legs away from the center of the Canopy. The Canopy will slowly begin to unfold, as shown in Figure A, below.

Continue to gently pull the outer legs while stepping backwards until the Canopy is fully opened. Caution: Do not pull too hard on the Outer Legs or the Canopy’s side supports may bend. Also, supports may pinch fingers while unfolding; keep fingers clear.

To raise the height of the Canopy, press your foot down on one of the feet at the bottom of an outer leg. While holding down the bottom half of the leg with one hand, use your free hand to slide the top half of the leg up. Do this until the snap button locks into place. See Figure B, next page.

1.

2.

3.

4.

5.

Figure A

Outer LegOuter Leg


Repeat this step for the Canopy’s remaining three legs.

Wrap the velcro straps that are connected to the Canopy around the frame struts. This will help increase the Canopy’s stability. See Figure C, above.

To secure the Canopy to the ground, push the Stakes (3) through the holes in the outer leg’s feet and into the ground. See Figures d1 and d2, below.

Tie the Guy Rope Strands (4) to the anchor ring on each corner of the Canopy and to a separate stake. See Figures e1 and e2, below. please note: The eight metal Stakes (3) and four Guy Rope Strands (4) are packed in the velcro pocket on the Canopy’s Carrying Bag.

6.

7.

�.

9.

Figure B

Outer Leg

Snap Button

Figure C

Velcro Strap

Frame Strut

Figure d1 Figure d2

Figure e1 Figure e2

Stake (3)Foot hole

Stake (3)

Rope (4)Anchor Ring


MAiNteNANCe ANd SerViCiNgdamaged products can fail, causing personal injury. do not use a damaged product. if abnormal noise or vibration occurs, have the problem corrected before further use.

Cleaning, maintenance, and lubricationBeFOre eACH uSe, inspect the general condition of the Canopy. Check for misalignment or binding of moving parts, tears or broken parts and any other condition that may affect its safe operation.

AFter uSe, clean Canopy cover off with clean, moist cloth.

Place folded Canopy into carrying bag and store in secure area out of reach of children.

1.

2.

3.

CAutiONCAutiON

pleASe reAd tHe FOllOWiNg CAreFullyTHE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER ASSUMES ALL RISK AND LIABILITy ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Folding the CanopyRemove Stakes (3) from the feet and untie Guy Rope Strands (4). Then unfasten the Canopy’s velcro tabs from around the frame.

With another person’s help, lift up two adjacent legs slightly and depress the frame’s snap buttons. See Figure F, right. Begin pushing the outer legs to the middle of the Canopy.

Repeat this step for the remaining two legs. Slightly lift Canopy off the ground and push outer legs closer together until fully closed.

Press the outer leg’s snap buttons and slide the upper half of the legs over the lower half.

During folding, shake the Canopy a little bit and brush off any twigs or debris. Dry off Canopy if damp.

Slide the collapsed Canopy into the Carrying Bag and tuck Stakes and Rope Strands into velcro pocket.

1.

2.

3.

4.

5.

6.

Figure F

Snap Button

Page �SKU 97173 For technical questions, please call 1-800-444-3353.

pArtS liSt ANd pHOtOpart description Q’ty

1 Canopy 12 Carrying Bag 1

part description Q’ty3 Stakes �4 Rope (strands) 4

record product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not avail-able individually as replacement parts.

1

3 4

2

10’ X 10’ CANOpy - Harbor Freight...

Documents

Transcript of 10’ X 10’ CANOpy - Harbor Freight...