10. Combustion Engines - | University of...
Transcript of 10. Combustion Engines - | University of...
![Page 1: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/1.jpg)
10. Combustion EnginesIntroduction
• This section will address the basic features andoperating principles of practical combustion sys-tems, mainly internal combustion engines, pre-dominantly used for propulsion.
• External combustion engines will be described,but will not be discussed.
• The distinction between internal and external com-bustion engines is dependent on the nature of theworking fluid.
10. Combustion Engines 1 AER 1304–ÖLG
![Page 2: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/2.jpg)
• Working fluid, as the name implies,- produces work by pushing on a piston or tur-bine blade that in turn rotates a shaft, or
- works as a high momentum fluid that is useddirectly for the propulsive force.
• In internal combustion engines, the energy sourceis a combustible mixture, and the combustionproducts is the working fluid.
• In external combustion engines, the combustionproducts is used to heat a second fluid that acts asthe working fluid.
10. Combustion Engines 2 AER 1304–ÖLG
![Page 3: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/3.jpg)
• With this definition, these are the most commoninternal combustion engines:- Gasoline engines (also known as spark-ignition, SI): homogeneous/stratified charge.
- Diesel engines (also known as compression-ignition, CI, engines).
- HCCI engines (homogeneous charge compres-sion ignition): currently under-development.
- Gas turbine engines: aircraft propulsion; sta-tionary power production.
- Chemical rockets.
10. Combustion Engines 3 AER 1304–ÖLG
![Page 4: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/4.jpg)
• Examples of external combustion engines:- Steam power plants.- Home heating furnaces fuelled by gas or oil.- Stirling engines.
• What kind of engines are the following?- Solar power plant.- Nuclear power plant.- Fuel cells.- Electrical rocket propulsion.
10. Combustion Engines 4 AER 1304–ÖLG
![Page 5: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/5.jpg)
Internal Combustion Engines
• Steady Flow internal combustion engines:- Gas Turbine- Ramjet / Scramjet- Chemical Rockets
• Non-steady Flow internal combustion engines:- Non-premixed charge- Premixed charge- Stratified charge
10. Combustion Engines 5 AER 1304–ÖLG
![Page 6: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/6.jpg)
10. Combustion Engines 6 AER 1304–ÖLG
![Page 7: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/7.jpg)
Gas Turbine Engines
• Aircraft Jet Engines:- Turbojet engines: all jet except for workneeded for the turbine that drives the com-pressor.
- Turbofan engines: part jet, part shaft work todrive a fan (in addition to the compressor).The fan privides about 5-6 times more airpassing around the engine core.
10. Combustion Engines 7 AER 1304–ÖLG
![Page 8: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/8.jpg)
- Turboprop engines: same as turbofan, but therate of airflow through the propeller may be25 to 30 times the airflow through the coreengine.
• Turboshaft Engines:- Industrial stationary engines used for powerproduction: electricity generation; to drive apump.
- To drive a rotor (helicopter), or to drive aship’s propeller.
10. Combustion Engines 8 AER 1304–ÖLG
![Page 9: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/9.jpg)
10. Combustion Engines 9 AER 1304–ÖLG
![Page 10: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/10.jpg)
10. Combustion Engines 10 AER 1304–ÖLG
![Page 11: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/11.jpg)
Turboshaft engine.
10. Combustion Engines 11 AER 1304–ÖLG
![Page 12: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/12.jpg)
10. Combustion Engines 12 AER 1304–ÖLG
![Page 13: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/13.jpg)
Turbofan engine.
10. Combustion Engines 13 AER 1304–ÖLG
![Page 14: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/14.jpg)
Turbojet internal total pressure.
10. Combustion Engines 14 AER 1304–ÖLG
![Page 15: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/15.jpg)
Historical trend of engine pressure ratio.
10. Combustion Engines 15 AER 1304–ÖLG
![Page 16: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/16.jpg)
Historical trend of turbine entry temperature.
10. Combustion Engines 16 AER 1304–ÖLG
![Page 17: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/17.jpg)
Three main combustor types.
10. Combustion Engines 17 AER 1304–ÖLG
![Page 18: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/18.jpg)
Multi-can combustor arrangement.
10. Combustion Engines 18 AER 1304–ÖLG
![Page 19: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/19.jpg)
Annular Combustor.
10. Combustion Engines 19 AER 1304–ÖLG
![Page 20: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/20.jpg)
Schematic of a turbojet with afterburner.
10. Combustion Engines 20 AER 1304–ÖLG
![Page 21: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/21.jpg)
Combustion in Gas Turbines:
• Spray combustion (liquid fuels)• Ignition• Flame stability - combustion noise• Flame propagation• Pollutant formation [CO, unburned HC, NOx,soot]
• Heat transfer• Cooling / dilution
10. Combustion Engines 21 AER 1304–ÖLG
![Page 22: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/22.jpg)
Current Combustion Problems in Gas Turbines:
• NOx control• Combustion noise (hooting)• Soot formation (carbon formation)• Fidelity of CFD of combustion codes
Current Combustion Developments in Gas Turbines:
• Lean-premixed combustion [NOx control, soot]• Hydrogen-enrichment [NOx, efficiency]• Higher pressure ratios [efficiency]
10. Combustion Engines 22 AER 1304–ÖLG
![Page 23: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/23.jpg)
Ramjets
• Simplest of air-breathing engines.• A diffuser, a combustion chamber, and an exhaustnozzle.
• Most suitable for supersonic speeds.• Compression by ram effect.• Fuel injection into compressed flow - flame hold-ers to stabilize flame.
• Combustion gases expand to high velocity in thenozzle.
10. Combustion Engines 23 AER 1304–ÖLG
![Page 24: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/24.jpg)
Schematic diagram of a ramjet engine.
10. Combustion Engines 24 AER 1304–ÖLG
![Page 25: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/25.jpg)
Chemical Rockets• Liquid Fuel Rockets: Fuel and oxidizer are storedin separate thin-walled tanks at low pressure. Be-fore combustion, they pass through turbine-drivenpumps and are injected to combustion chamber,where they burn at high pressure.
• Solid Fuel Rockets: Entrire block of propellant(consisting of premixed fuel and oxidizer) storedwithin the combustion chamber. Combustion pro-ceeds from the surface of the propellant grain at arate that depends on pressure and temperature andgeometry of the burning surface.
10. Combustion Engines 25 AER 1304–ÖLG
![Page 26: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/26.jpg)
Schematic diagram of a rocket engines.
10. Combustion Engines 26 AER 1304–ÖLG
![Page 27: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/27.jpg)
Nonequilibrium expansion:• Equilibrium composition depends on pressure andtemperature, for given fuel and Φ, and may in-clude large quantities of dissociated material.
• In the exhaust nozzle dissociated compounds tendto recombine because of temperature drop.
• This exothermic recombination reactions may actas a heat source in the flow.
• Following Fig. illustrates relative importance ofdissociation energies before and after an equilib-rium expansion of a stoichiometric H2-O2 mixture.
10. Combustion Engines 27 AER 1304–ÖLG
![Page 28: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/28.jpg)
10. Combustion Engines 28 AER 1304–ÖLG
![Page 29: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/29.jpg)
• For products to maintain their equilibrium com-position as they expand, recombination reactionsshould be fast enough to keep pace with rapid ex-pansion.
• Since expansion process is very rapid, this condi-tion is not always met.
• In the limit, i.e. τrecomb >> τexpan
we have frozen flow at constant composition.• Difference between equilibrium and frozen flowcan be appreciable for some propellants.
10. Combustion Engines 29 AER 1304–ÖLG
![Page 30: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/30.jpg)
Current Combustion Problems in Rockets:
• Combustion Instabilities: Both liquid- and solid-propellant rockets are subject to combustion insta-bilities in the form of large pressure oscillationswithin the chamber that may lead to engine fail-ure.
• Low-frequency oscillations (about 100 Hz) due tocoupling between combustion and feed system.
• High-frequency oscillations (several thousand Hz):thermo-acoustics, i.e., coupling between combus-tion and acoustics (and flow field).
10. Combustion Engines 30 AER 1304–ÖLG
![Page 31: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/31.jpg)
• In solid-propellant rockets, burning rate is verysensitive to pressure and velocity.
• Energy release and propellant velocity or pressurepattern that causes nonuniformity can interact toproduce sustained oscillations.
• Such oscillations lead to high rates of erosiveburning that may change the chamber geometryto stable burning or may lead to engine failure.
• Burning rate of solid propellants• Atomization/mixing in liquid-propellant rockets.
10. Combustion Engines 31 AER 1304–ÖLG
![Page 32: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/32.jpg)
Assignment
• Visit www.howstuffworks.com and read:- How car engines work?- How gas turbine engines work?- How rockets work?
• From links, visit sites related to gas turbines androcket propulsion.
10. Combustion Engines 32 AER 1304–ÖLG
![Page 33: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/33.jpg)
Spark-Ignition & Compression-Ignition Engines
• In our formal definition of internal combustionengines, we included the gas turbines and rocketsunder this classification. Conventionally, however,the term internal combustion engines is used forspark-ignition and compression-ignition engines.
• Spark-ignition engines (Otto cycle engines, orgasoline engines, or petrol engines, though otherfuels can be used).
• Compression-ignition engines (diesel engines andHCCI engines).
10. Combustion Engines 33 AER 1304–ÖLG
![Page 34: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/34.jpg)
10. Combustion Engines 34 AER 1304–ÖLG
![Page 35: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/35.jpg)
Flame front Fuel spray flame
Premixed charge (gasoline)
Non-premixed charge (Diesel)
Spark plug Fuel injector
Fuel + air mixture Air only
Schematics of SI and CI engines.
10. Combustion Engines 35 AER 1304–ÖLG
![Page 36: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/36.jpg)
Schematic diagram of a gasoline engine.
10. Combustion Engines 36 AER 1304–ÖLG
![Page 37: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/37.jpg)
Four-stroke SI engine operating cycle.
10. Combustion Engines 37 AER 1304–ÖLG
![Page 38: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/38.jpg)
Four-stroke cycle SI engine:
• Majority of reciprocating engines operate as thefour-stroke cycle.
• Each cylinder requires four strokes of its piston- two revolutions of the crankshaft - to completesequence of events which produces one powerstroke.
• Both SI and CI engines use this cycle.• The four strokes are: Intake, compression, power,and exhaust.
10. Combustion Engines 38 AER 1304–ÖLG
![Page 39: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/39.jpg)
• Intake stroke: starts with piston at TC and endswith piston BC, which draw fresh mixture intocylinder. To increase mass inducted, inlet valveopens shortly before stroke starts and closes afterit ends.
• Compression stroke: both valves are closed andthe mixture inside the cylinder is compressed toa small fraction of its initial volume. Toward theend of the compression stroke, combustion is initi-ated and the cylinder pressure rises more rapidly.
10. Combustion Engines 39 AER 1304–ÖLG
![Page 40: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/40.jpg)
• Power stroke: or expansion stroke:- starts with the piston at TC and ends at BCas the high-temp., high-pressure, gases pushthe piston down and force the crank to rotate.
- About five times as much work is done onthe piston during the power stroke as the pis-ton had to do during compression.
- As the piston approaches BC the exhaustvalve opens to initiate the exhaust processand drop the cylinder pressure to close to theexhaust pressure.
10. Combustion Engines 40 AER 1304–ÖLG
![Page 41: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/41.jpg)
• Exhaust stroke: where the remaining burned gasesexit the cylinder:- first, because the cylinder pressure may besubstantially higher than the exhaust pressure;
- then as they are swept out by the piston as itmoves toward TC.
- As the piston approaches TC the inlet valveopens. Just after TC the exhaust valve closesand the cycle starts again.
10. Combustion Engines 41 AER 1304–ÖLG
![Page 42: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/42.jpg)
Two-stroke cycle SI engine:• The four-stroke cycle requires, for each enginecylinder, two crankshaft revolutions for eachpower stroke.
• To obtain a higher output from a given enginesize, and a simpler valve design, the two-strokecycle was developed.
• The two-stroke cycle (as four-stroke cycle) is ap-plicable to both SI and CI engines.
• The two strokes are: compression, and power orexpansion.
10. Combustion Engines 42 AER 1304–ÖLG
![Page 43: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/43.jpg)
Two-stroke engine operating cycle.
10. Combustion Engines 43 AER 1304–ÖLG
![Page 44: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/44.jpg)
• Compression stroke: starts by closing the inlet andexhaust ports, and then compress the cylinder con-tents and draws fresh charge into crankcase. Asthe piston approaches TC, combustion is initiated.
• Power or expansion stroke: similar to that in four-stroke cycle until the piston approaches BC, whenfirst the exhaust ports and then the intake portsare uncovered. Most of burned gases exit cylin-der in an exhaust blowdown process. When inletports are uncovered, fresh charge which has beencompressed in crankcase flows into cylinder.
10. Combustion Engines 44 AER 1304–ÖLG
![Page 45: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/45.jpg)
Four-stroke CI engine operating cycle.
10. Combustion Engines 45 AER 1304–ÖLG
![Page 46: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/46.jpg)
Wankel engine operating cycle.
10. Combustion Engines 46 AER 1304–ÖLG
![Page 47: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/47.jpg)
Wankel engine operation:
• Wankel rotary engine operates with the four-strokecycle.
• As the rotor makes one complete rotation, the ec-centric shaft rotates through three revolutions.
• As the rotor makes one rotation, each chamberproduces one power stroke.
• Three power pulses occur for each rotor revolu-tion; thus for each eccentric shaft revolution thereis one power pulse.
10. Combustion Engines 47 AER 1304–ÖLG
![Page 48: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/48.jpg)
Combustion in SI Engines:• Mixture preparation:
- Carburation (no longer used in North Ameri-can markets).
- Port injection - fuel is sprayed into the airstream just before the inlet valve.
- Direct injection - fuel is injected into thecylinder (DISI).
• Ignition: spark plug.• Flame kernel development and flame propagation.
10. Combustion Engines 48 AER 1304–ÖLG
![Page 49: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/49.jpg)
• Engine knock:- Fuel octane number- Engine compression ratio
• Pollutant formation:- Nitric oxides, NOx- Carbon dioxide, CO- Unburned hydrocarbons, HC
• Exhaust treatment:- Catalytic converters
10. Combustion Engines 49 AER 1304–ÖLG
![Page 50: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/50.jpg)
Burned
Unburned
Cross-section of a gasoline engine combustionchamber.
10. Combustion Engines 50 AER 1304–ÖLG
![Page 51: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/51.jpg)
Combustion in a CI engine:
• Direct in-cylinder injection (large engines).• Prechamber injection (passenger car engines).• Spray combustion:
- Compression ignition - ignition delay- Diesel fuel cetane number
• Pollutant formation:- NOx, CO, HC, Soot (particulates)
• Particulate trap and catalytic converter.
10. Combustion Engines 51 AER 1304–ÖLG
![Page 52: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/52.jpg)
10. Combustion Engines 52 AER 1304–ÖLG
![Page 53: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/53.jpg)
10. Combustion Engines 53 AER 1304–ÖLG
![Page 54: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/54.jpg)
Heat release in diesel engine combustion.
10. Combustion Engines 54 AER 1304–ÖLG
![Page 55: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/55.jpg)
EXHAUSTEMISSIONS
INJECTION AND SPRAYCHARACTERISTICS
FUEL-AIRMIXING
PROCESSIGNITION
Air InletInlet Port DesignChamber Design
Turbocharge
AIR MOTION / TURBULENCEIN THE
COMBUSTION CHAMBER
Fuel Properties
MOSTLYNON-PREMIXEDCOMBUSTION
PARTIALLY"PREMIXED"
COMBUSTION
Injection TimingInjection System Design
Injection DurationInjection Rate
EGR
HEAT RELEASERADIATION EXCHANGE BETWEENHOT AND COLD POCKETSNOX & SOOT FORMATIONSOOT OXIDATION
Processes in the diesel engine combustion.
10. Combustion Engines 55 AER 1304–ÖLG
![Page 56: 10. Combustion Engines - | University of Torontoarrow.utias.utoronto.ca/~ogulder/ClassNotes10.pdf · 10. Combustion Engines Introduction • This section will address the basic features](https://reader034.fdocuments.in/reader034/viewer/2022042707/5a70289a7f8b9ab1538bb4b6/html5/thumbnails/56.jpg)
August 5-9, 2001 DEER Workshop Caterpillar Engine ResearchDiesel & Emissions Technology
What is HCCI?
hot flame region:nitric oxideshot flame region:
nitric oxides + smoke
Diesel Engine(compression ignition)
Gasoline Engine(spark ignited)
HCCI Engine(Homogeneous Charge Compression Ignition)
Low temperature combustionultra low emissions
spark plugfuel injector