1 Wally and Carey - muffinheadpatterns.com

COPYRIGHT ©2016 DT SEWVERSITY. ALL RIGHTS RESERVED. PATTERN SUPPORT: [email protected]

1

Wally and Carey

Sewing Project 13


2

DESCRIPTION- Wally is a wallet with a button closure and an optional zipper pouch.

RECOMMENDED FABRICS: COTTON, DENIM IF USING DENIM, THE INSIDE LAYER SHOULD BE LIGHTWEIGHT COTTON.

45” WIDE FABRIC REQUIREMENTS -YARDS: .50 yards Notions: .5 yards of lightweight interfacing

Terms Of Use: you may use this pattern to make items to sell in quantities less than 100 per year. This pattern is not to be shared, sold, duplicated or transferred to another in any way. If you are purchasing this pattern to teach a sewing class, each student MUST purchase their own copy.

DESCRIPTION- Carey is a card holder, perfect for cards and other small, flat items.

RECOMMENDED FABRICS: COTTON, DENIM IF USING DENIM, THE INSIDE LAYER SHOULD BE LIGHTWEIGHT COTTON.

45” WIDE FABRIC REQUIREMENTS -YARDS: .25 yards

Notions: .25 yards of lightweight interfacing, .75” diameter button One 7” regular zipper for optional zippered pouch.


3PRINTING INSTRUCTIONSBe sure to set your printer to not scale the pattern pieces by selecting either “Actual Size” or “Custom Scale: 100%” in your print dialog.

Wally

Carey


4Fabric Layout: 45” width, folded in half lengthwise. Extra fabric will be required for prints, directional fabric or fabric with a nap.

Selvages

Fold

Wally Carey

Selvages

Fold

Piece A: Cut 2 of Fabric, Cut 1 of Interfacing Piece B: Cut 2 of Fabric, Cut 1 of Interfacing Piece C: Cut 2 of Fabric, Cut 1 of Interfacing Piece D: Pocket: Cut 1 on Fold of Fabric for Each Pocket Desired Piece E: Zipper Pouch: Cut 2 of Fabric, Cut 2 of Lining (Optional)

Piece 1: Front and Back Cut 2 of Fabric, Cut 1 of Interfacing Piece 2: Pockets Cut 4 of Fabric, Cut 2 of Interfacing Piece 3: Tab Cut 2 of Fabric, Cut 1 of Interfacing

12

3

A

B

C

E

D

2


5

Right Side Wrong Side

Transfer all markings. read The inTrucTions before beginning To sew. All seam allowances are included and are 1/2” unless specifically stated otherwise.

1. Apply fusible interfacing to the wrong sides of your outer wallet sections A and B. Apply interfacing to both “C” pieces. The remaining sections will be referred to as the inner wallet.

3. For each pocket desired, align the raw edges of the folded pocket piece to the right side of one of the rectangular wallet sections. The fold will be the top of the pocket. Stitch the pocket along the sides and bottom using a 1/4” seam allowance.

Fold at Top of Pocket

4. Prepare the zipper pouch (Optional)- Place the zipper face down over the right side of one of the zipper pouch pieces.

5. Place another pouch section face down over the zipper. The zipper is between the two layers. The remaining two pieces will be the lining.

WALLY

ABC

noTe: You maY place pockeTs on pieces b or c. You maY choose To puT The pockeTs on The righT sides of The ouTer walleT, The inner walleT, or boTh.

2. Fold the pocket in half widthwise. Topstitch along the fold in a 1/4” seam allowance if desired.

D

B,C

E

E


66. Sew the layers together, sewing as close to the zipper teeth as possible. Unfold and press. Repeat steps 4 and 5 on the opposite side of the zipper.

7. Both pieces of lining should be to one side and both pieces of the outer should be to the other. The zipper teeth are pinned toward the lining.

Wrong Side Fabric

Wrong Side Lining

8. Sew the sides closed. Push the zipper pull to the middle. Sew along the outside edges of the metal parts of the zipper. Leave the bottom of the bag open. Clip the corners and trim the seams. Trim off the excess zipper tape.

9. Turn the bag right side out. Baste the bottom edge together using a 1/4” Seam allowance.

10. Sew the three outer wallet sections right sides together. Be sure that the top of the pockets face the top of the wallet if placed in the middle section.

TopI

A

B

C


7

11. Right sides together, place your zipper pouch between two of the rectangular inner wallet sections. Sew the two sections together.

12. Sew the top to the inner wallet, right sides together. The zipper pouch will be on the right side.

13. Place the inner wallet over the outer wallet, right sides together. Sew as shown leaving a 3” opening at the bottom for turning. Clip the corners, and notch the curve. Trim the seams except for the bottom edge. Turn that edge 1/2” toward the wrong side and press.

14. Turn the wallet right side out. Slipstitch the opening closed. Topstitch 1/8” around the wallet if desired.

16. Sew the button as marked.

I

I

Wrong Side

Right Side

15. Make the buttonhole.

A

B

C

B

C

Zipper Pouch


8Carey

Right Side Wrong Side

Transfer all markings. read The inTrucTions before beginning To sew.

All seam allowances are included and are 1/2” unless specifically stated otherwise.

1. Apply interfacing to the wrong sides of the tab, the front and the pockets.

2. Right sides together, sew an interfaced pocket to one without interfacing across a long edge. Trim the seam. Turn right side out. Topstitch 1/4” from the top if desired. The top stitched edge will be the top of the pocket. Repeat with the remaining pocket.

3. Place one of the pockets face up on the right side of the back piece. Sew along the short edges and the bottom using a 1/4” seam allowance. Repeat on the other side with the remaining pocket.

4. Sew the pockets to the back along the stitching lines. (If you want to customize your pocket, arrange your items in the pocket as you like. Re-draw the stitching lines to hold the items securely. Stitch through your new stitching lines).

5. Right sides facing, sew the tab pieces together. Leave the bottom open.Trim the seam and turn right side out.

Back right Side


96. Align the raw edges of the tab to the raw edge of the back as marked. The tab placement for the quater fold is on the left. For the half fold, it is in the center. Baste the tab in place using a 1/4” seam allowance.

7. Right sides facing, sew the back to the front leaving the bottom open between the markings.

8. Clip the bottom seam up to the reinforcement stitching at the opening. Press the seam up 1/2” on both sides.

9. Clip all four corners. Trim the remaining seams and finish the edges.

10. Turn the wallet right side out, press. Slipstitch the opening closed or topstitch 1/4” all the way around the wallet if desired.

11. Fold the wallet in quarters or in half if preferred. Sew the socket part of the snap to the front as marked. Sew the ball part of the snap to the tab.

Finished quarter Fold

Finished Half Fold

CCut 2 of FabricCut 2 of Interfacing

BCut 2 of FabricCut 1 of interfacing

2” x 2” test square

11WallyWally

2DPocketCut 1 on fold for each pocket desired.

FoldPocket Top

Pocket Bottom

BCut 2 of FabricCut 1 of interfacing

Piece A Cut 2 of FabricCut 1 of interfacing

Wally

Wally

3 E.Zipper Pouch (Optional)

Cut 4 of fabric

Wally

1

1. CareyFront and BackCut 2 of FabricCut 1 of Interfcing

Tab placement If folding in Quarters

Snap Placement

Tab placement If folding in Half


2Tab placement If folding in Half

3


2. CareyPockets Cut 4 of FabricCut 2 of Interfacing

3. C

arey

Tab

Cut 2

of f

abric

Cut 1

of I

nter

faci

ng


4

1 Wally and Carey - muffinheadpatterns.com

Documents

Transcript of 1 Wally and Carey - muffinheadpatterns.com