1 NS1000 V3.0 - System Resource and Peripheral Incensement - Rev1.1 31 July, 2013.

1

NS1000 V3.0

- System Resource and Peripheral Incensement -

Rev1.1 31 July, 2013

2

Table of Contents

1. Overview2. What is enhancement 3. How to program

3

Chapter 1

Overview

4

1. Overview

Selectable System capacity (flexibility configuration) Solution

3 types of system capacity patterns

Features and Benefits >>

When you want to increase NT-phone capacity or H.323 capacity, you can change the system capacity on customer demand.

NS1000 supports TDA100D via Stacking card. TDA100D is added for Legacy Gateway of NS1000.

* Features New for V3

5

NS1000 adds new 2 types of system capacity patterns. System capacity can be selectable based on customer demand.

Type-1: Standard Type (same as version 1.x & 2.x) Same as current System resource. This type will be used for the user who satisfy current system configuration.

Type-2: IP Extension Type Increase number of IP terminal and decrease number of SIP terminal This type may be used for the user who want to increase NT phone.

Type-3: System Resource Type Increase Tenant and H323 expanding This type may be used for the user who want to increase more Tennant and/or Q-Sig node

Note: This selection must be set when proceeding Easy Setup Wizard

TDA100D Cabinet can be Legacy GW for NS1000.

Add supported optional cards for Legacy GW.

1. Overview

6

Chapter 2What is enhancement

7

When select Type2 mode, IP-PT extension capacity will be increased up to 640.In Type3 mode, SIP extension capacity will be changed.

2-1 Selectable System capacity

Type Stand alone One Look Type1 Extension Capacity 640 1000

　

IP-PT (KX-NT series) 256 1000SIP 640 1000

　 SIP Phone 640 1000KX-UT series 640 1000

Type 2Extension Capacity 640 1000

　



Type 3Extension Capacity 640 1000

　



Selectable Extension capacity

8

When select Type3 mode, IP-GW (H323) capacity will be increased up to 96

Selectable IP-GW Capacity

Type Stand alone One Look Type1 IP GW 256 256

　H323 48 96SIP 256 256

Type2 IP GW 256 256

　H323 48 96SIP 256 256

Type3IP GW 256 256

　H323 96 128SIP 160 256


9

When select Type3 mode Tenant Group capacity will be increased up to 128

Type Stand alone One Look Type1 - Tenant

　

Tenant Group 32 32

Time Table 32 32

System Speed Dial 1000/Tenant 1000/Tenant

Type2 - Tenant

　

Tenant Group 32 32

Time Table 32 32


Type3 - Tenant

　

Tenant Group 128 128

Time Table 128 128


Selectable Tenant Group capacity


10

COS 512, Carrier 128 per standalone unit

Increase COS and Carrier for each Unit

Other resources will be increased

Resource 　 Before (V1,V2) After (V3)

Type1

　　　　　

ARS Carrier 48 128

No. of COS Group 64 512

User Group 96 256

Type2

　　　　　

ARS Carrier 48 128


User Group 96 256

Type3

　　　　　

ARS Carrier 48 128


User Group 96 256


11

2-2 Add TDA100D as Legacy GW

Legacy Gateway by KX-TDA100D

Cabinet of KX-TDA100D can be used as Legacy Gateway to expand legacy trunks and phones. NS1000 can have stacking connection with TDA100D by changing MPR card to STACK-S card in TDA100D same as TDE series (KX-NS0132).

KX-TDA100D is allowed to be set with another KX-TDA100D on a NS1000 as Legacy Gateway. TDA100D add as additional GW category.

Insert STACK-S card

Remove MPR card

TDA100D

Stack-S card S/W Version should be 2.000 or later

- Category1: NCP500 /NCP1000 - Category2: TDE100/200, TDA100/200 - Category3: TDE600/620, TDA600/620 - Category4: TDA100D

1212

The maximum number of Legacy Trunk and Extension

Stand-alone Stacking system

One LookNetworking

Main Main

1NCP5001NCP1000

1TDE/TDA1001TDA100D

1TDE/TDA 2001TDE/TDA 600

2NCP5002NCP1000

2TDE/TDA 1002TDA100D

2TDE/TDA 2002TDE/TDA 600

Trunk(ch) 256 256 600

Legacy 30 0 64/64/120/120/128/160 128/128/240/240/256/256 600

LCOT 2 0 12/16/96/112/128/160 24/32/192/224/256/256 600

BRI 8 0 12/16/96/112/128/160 24/32/192/224/256/256 600

PRI23 23 0 46/46/92/92/92/115 92/92/184/184/184/230 600

PRI30 30 0 60/60/120/120/120/150 120/120/240/240/240/256 600

T1 0 0 48/48/96/96/96/120 96/96/192/192/192/240 600

E1 0 0 60/60/120/120/120/150 120/120/240/240/240/256 600

Extension(ch) 640 640 1000

Legacy*1 2 0 44/44/128/120/168/240 88/88/256/240/336/480 1000

SLT 2 0 36/36/96/120/128/240 72/72/192/240/336/480 1000

DPT 0 0 40/40/96/112/128/160 80/80/192/224/256/320 1000

*1 : The maximum number with DXDP

2-2 Add TDA100D as Legacy GW

Legacy Gateway by KX-TDA100D

1313

Following cards are supported for Legacy Gateways

2-3 Add Optional cards

Optional cards for Legacy Gateway

Model Symbol Description

KX-TDA1176 MCSLC16 16-Port Single Line Telephone Card with Message LampInterface

KX-TDA1178 MCSLC24 24-Port Single Line Telephone Card with Message LampInterface


KX-TDA6179 EMCSLC24 24-Port Single Line Telephone Card with CID & MessageLamp Interface


KX-TDA1180 CLCOT8 8-Port Analogue Trunk Card with CID

KX-TDA1186 CLCOT8E 8-Port Analogue Trunk with Caller ID daughter Card

For TDE100/200, TDA100D

For TDE600/620

For TDA100D

14

Chapter 3How to Program

15

3. Howe to Program

System Initialize > Easy Setup Wizard

It is necessary to select the type while proceeding Easy Setup Wizard, when you want to change System Capacity Type. System Capacity Type can’t be changed while system running unless initialize NS1000.

Note: You can not select System Capacity Type when you upgrade software from Version 2 to Version 3 without Off-Line Tool.

16

END

17

Appendix

18

Appendix

System capacity

When you select type 2 or type 3 system capacity, V-SIPEXT capacity is changed at each type. Default : <Type 1> 20 cards (640 ports)

System Capacity Type 2SIPEXT : 8 cards (256 ports)

System Capacity Type 3SIPEXT : 12 cards (384 ports)

19

Modification

20130730-01 5 NS1000 V3.0 System Resource and Perifperal_Rev1.0_30Jul2013.pptx - 1st release20130731-01 Modified page 5 ‘overview’ and page 13 ‘Description for card’ . - Revision 1.1

1 NS1000 V3.0 - System Resource and Peripheral Incensement - Rev1.1 31 July, 2013.

Documents

Transcript of 1 NS1000 V3.0 - System Resource and Peripheral Incensement - Rev1.1 31 July, 2013.