1 High-Speed Digital Test & Measurement Chris Allen ([email protected]) Course website URL...
-
Upload
grant-walker -
Category
Documents
-
view
218 -
download
0
Transcript of 1 High-Speed Digital Test & Measurement Chris Allen ([email protected]) Course website URL...
1
High-Speed DigitalTest & Measurement
Chris Allen ([email protected])
Course website URL people.eecs.ku.edu/~callen/713/EECS713.htm
2
TopicsTest equipment
Oscilloscope characteristicsOscilloscope probes
• Passive probes• Active probes• Probe inductance from ground lead
Design for test
Test proceduresMeasuring noise marginMeasuring timing marginSensitivity to supply voltage variationsSensitivity to temperature variationsTest vectors
Future trends
3
Test equipmentOscilloscope characteristics
Vertical amplifier bandwidth (typically specified as 3-dB BW, BW3dB)
Limits the observed risetime of the measured signal
The risetime of the vertical amplifier adds in root-sum-square (RSS) fashion to the circuit’s actual Tr to yield a measured Tr
amplifierverticalTcircuitTmeasuredT 2r
2rr
Note: to relate BW3dB to T10-90 T10-90 = 0.338 / BW3dB
4
Test equipmentScope probe characteristics
The probe connecting the oscilloscope to the circuit under test also has a frequency response, characterized by Tr(probe), that affects the measurement.
Including the contribution of the scope probe yields
Consequently, the circuit’s actual risetime may be shorter than what measurements indicate.
Example: Using a 500-MHz oscilloscope with a 1-GHz probe an 820-ps risetime is measured. What is the circuit’s actual risetime?
500 MHz Tr(vert amp) = 676 ps, 1 GHz Tr(probe) = 338 ps
probeTamplifierverticalTcircuitTmeasuredT 2r
2r
2rr
ps318ps338ps676ps820circuitT 222r
5
Test equipmentScope probe characteristics
The model for the probe includes an input capacitance in parallel with a high-value resistance, R1 (9 MΩ) and an inductive ground lead.
The scope is modeled as a high-value resistor, R2, in parallel with an input capacitance, C2.
6
Test equipmentScope probe characteristics
At DC this arrangement produces a 10x attenuation by the voltage divider R2/(R1 + R2).
At DC the impedance of the probe/scope is|Zmeas| = 10 MΩ.
At 100 MHz the impedance is(ignoring XLGround Lead
)
C1 (12 pF) |XC1| = 133
C2 (20 pF) |XC2| = 80
C3 (55 pF) |XC3| = 29
|Zmeas| |XC1 + (XC2
// XC3)| = 154
At higher frequencies, the probe/scope impedance decreases further.
Simplified equivalent circuitSimplified equivalent circuit
7
Test equipmentOther measurement considerations
The relatively low probe/scope impedance at high frequencies can load the circuit under test causing:
• changes in circuit performance
• corrupt measurements
To avoid the loadingproblem we can useprobes with lesscapacitance.
Another option is touse active probesthat use FETamplifiers to isolatemeasurement capacitance from thecircuit under test.
8
Test equipmentActive probes
The FET in the active probe acts as a signal buffer.The probes’s input impedance is now the FET’s input impedance
• typical FET input capacitance < 1 pF
• high input resistance
Consequently, active probes
• reduce circuit loading
• have a wide operating bandwidth(Tektronix active probe 500 MHz to 4 GHz)
• requires a bias voltage to power the FET amplifier
Active probes can present a bias voltage to the probe tip
• useful for probing unterminated outputs
9
Test equipmentProbe inductance from ground lead
Oscilloscope measurements generally require a ground connection as a voltage reference.
Typical scope probes have a ground lead wire for signal reference.
This ground lead has significant inductance (100s of nH) and can act as an antenna (both radiating signals as well as coupling ambient RF signals into the measurement).
A long ground lead presents a number of measurement problems
• increased Tr(measured)
• crosstalk
• electromagnetic interference (EMI)
10
Test equipmentProbe inductance from ground lead
To avoid these problems we must reduce Lgnd
Special probe tip attachments provide a ground connection with reduced lead inductance (few nH)
These can improve the measurement-induced errors affecting Tr,
crosstalk, and EMI
However to effectively use these tip attachments allsignals to be probedmust have a nearby ground pad for the probe.
Therefore generous use of ground metal on the boardsurface facilitates probing.
11
Test equipmentSpecial probing fixtures
The author discusses a low-cost, shop-built 21:1 probebuilt from a length of coaxial cableand a leaded 1-kΩ resistor.
Benefits of this approach include
• high DC resistance of 1050 Ω (vs. 50 Ω of cable alone)
• low circuit loading, fast rise time (Tr)minimal capacitance (~ 0.5 pF)1-kΩ series resistance
• low cost
Assumptionsscope is terminated with 50 Ω (to reduce reflections)
ground pad is available near the signal to be probed (short lead length)
21:1048.0ratioDivision
100050
50ratioDivision
12
Test equipmentSpecial probing fixtures
Low-cost, shop-built 21:1 probe (photo essay)from http://paulorenato.com/joomla/index.php?option=com_content&view=article&id=93&Itemid=4
circuit under test: 125-MHz oscillatorcircuit under test: 125-MHz oscillator
testing with passive probestesting with passive probes
testing with shop-built, wide bandwidth probetesting with shop-built, wide bandwidth probe
13
Design for testSpecial probing fixtures
Special test points can also be incorporated into the board design to ease the probing of high-speed signals.
14
Test proceduresOnce a digital circuit is functioning, it is useful to determine
its operating margin
Consider the variety of factors that contribute to this margin
• noise margin
• reflections
• timing margin
• temperature effects
• supply voltage effect
Several tests are recommended to ensure reliable operation
15
Test proceduresNoise margin / reflection testing
By introducing additional noise at various nodes in the system, signals with noise sensitivity can be identified.
Useful in locating the source of intermittent errors.
The Noise Source is composed of resistor, R, that develops thermal noise (broadband, random) which is then amplified to the desired level.
Other noise generations approaches are available (e.g., communication noise sources).
16
Test proceduresTiming testing
By varying the relative timing of the clock and data signals, the timing margin can be estimated.
Use of a coaxial delay lineselect a clock orremove a portion insert a short
data line to of the line and segment ofbe tested expose the copper coaxial line
The opened trace can be readily repaired after testing
Another method for making this measurement is to use an independent clock source, synchronized with variable phase control.
Demonstrates usefulness of ground area on surface
17
Test proceduresTesting tolerance to varying supply voltages, VEE, VTT
Test to find out how sensitive your design is to voltage variations,to establish the supply voltage tolerances.
This test demonstrates another advantage of separate VEE and VTT supplies, as opposed to
These voltage variations can change threshold voltage and signal DC bias levels resulting in small timing changes.
18
Test proceduresTesting tolerance to varying temperature
Variations in ambient temperature can change the device temperature which may result in significant propagation delay changes.
The effect may be localized by selective temperature adjustment by applying local heat/cooling at the chip level to isolate the effect.
Heat gun
19
Test proceduresTest vectors
At the device level, board level, or system level comprehensive testing requires exercising all circuit functions at speed, simultaneously.
Testing functions independently is useful but not conclusive.
Such testing requires that all inputs and expected outputs be specified.These are known as test vectors
The inputs are used to stimulate the circuit and the responses are observed.
The test vectors bring the circuit or system to a known state (e.g., reset, or all 0s) and then steps through all states of interest.
20
Test proceduresTest vectors
Such testing brings together all factors affecting performance including timing, crosstalk, EMI, noise on the power and ground.
Such testing is often expensive and limited.
It typically involves an extensive variety of test equipment, programming, and planning.
21
Future trendsApplication-driven advances
Evolutionary and revolutionary advances require ever-increasing data rates and computational throughput in smaller packages while consuming less power.
Leading applications include:• computing (gaming consoles, super computers)• sensors (fine resolution video, radar, RFID)• wireless communication
Emerging technologies• energy harvesting (power derived from local environment)• optical interconnects die-to-die (optical transmitters/receivers integrated into die)
– may involve holographic reflectors or optically transparent substrates