1 CSWA 20resources/default.htm.
-
Upload
posy-flynn -
Category
Documents
-
view
265 -
download
0
Transcript of 1 CSWA 20resources/default.htm.
![Page 1: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/1.jpg)
1
CSWA
http://www.eng.uwo.ca/designcentre/CAD%20resources/default.htm
![Page 2: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/2.jpg)
2
DIMENSIONING AND TOLERANCING
![Page 3: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/3.jpg)
3
prismatic.sldasm
![Page 4: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/4.jpg)
4
DIFFERENT TYPES OF FIT
Clearance fit
Limits of size defined such that a clearance always results when mating parts are assembled
Interference fit
Limits of size are so prescribed that interference always results when mating parts are assembled.
Transition fit
Limits of size are so prescribed that either clearance or an interference may results when mating parts are assembled
Line fit
Limits of size are so prescribed that surface contact or clearance may result when mating parts are assembled
![Page 5: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/5.jpg)
5
BASIC HOLE SYSTEM
In the basic hole system the minimum (lower limit) hole size is taken as the basic size.
Stock hole is made “first” and then shaft is made to particular type of fit (to suit the hole).
![Page 6: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/6.jpg)
6
BASIC SHAFT SYSTEM
In the basic shaft system the maximum (upper limit) shaft size is taken as the basic size.
Stock shaft is created “first” and hole is made to particular type of fit (to suit the shaft).
![Page 7: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/7.jpg)
7
In the basic hole system the minimum (lower limit) hole size is taken as the basic size.
Stock hole is made “first” and then shaft is made to particular type of fit (to suit the hole).
In the basic shaft system the maximum (upper limit) shaft size is taken as the basic size.
Stock shaft is created “first” and hole is made to particular type of fit (to suit the shaft).
BASIC SHAFT OR BASIC HOLE?
![Page 8: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/8.jpg)
8
“Shaft”
“Hole”
-- =
=
What type of fit is this?
IDENTIFY FIT SYSTEM
![Page 9: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/9.jpg)
9
IDENTIFY FIT SYSTEM
![Page 10: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/10.jpg)
10
IDENTIFY FIT SYSTEM
Basic hole
More commonly used
Basic shaft
Less commonly used
![Page 11: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/11.jpg)
11
Shown are limit tolerances
IDENTIFY FIT SYSTEM
![Page 12: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/12.jpg)
12
Surface roughness for different manufacturing methods
http://mdmetric.com/pdf/surfruff.pdf
![Page 13: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/13.jpg)
13
![Page 14: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/14.jpg)
14
Φ
Basic hole fits
![Page 15: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/15.jpg)
15
Φ
Basic shaft fits
![Page 16: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/16.jpg)
16
Description of preferred fits
![Page 17: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/17.jpg)
17
ANSI PREFERRED HOLE BASIS METRIC CLEARANCE FITS
Pages 312, 313, 314, 315
ANSI PREFERRED SHAFT BASIS METRIC CLEARANCE FITS
Pages 316, 317, 318, 319
Engineering Design GraphicsJames LeakeJacob Borgerson
![Page 18: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/18.jpg)
18
cylindrical_metric.sldasm
Nominal diameter 25mm
Btw. what is wrong with this assembly?
![Page 19: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/19.jpg)
19
Loose running fit for nominal diameter 25mm preferred hole basic
![Page 20: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/20.jpg)
20
Free running fit for nominal diameter 25mm preferred hole basic
![Page 21: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/21.jpg)
21
Close running fit for nominal diameter 25mm preferred hole basic
![Page 22: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/22.jpg)
22
Sliding fit for nominal diameter 25mm preferred hole basic
![Page 23: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/23.jpg)
23
Locational clearance (line fit) for nominal diameter 25mm preferred hole basic
![Page 24: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/24.jpg)
24
Locational transition fit for nominal diameter 25mm preferred hole basic
![Page 25: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/25.jpg)
25
Locational transition fit for nominal diameter 25mm preferred hole basic
![Page 26: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/26.jpg)
26
Locational interference fit for nominal diameter 25mm preferred hole basic
![Page 27: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/27.jpg)
27
Medium drive fit for nominal diameter 25mm preferred hole basic
![Page 28: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/28.jpg)
28
Force fit for nominal diameter 25mm preferred hole basic
![Page 29: 1 CSWA 20resources/default.htm.](https://reader033.fdocuments.in/reader033/viewer/2022061600/56649d0a5503460f949dcb8c/html5/thumbnails/29.jpg)
29
Hole is always the same: H7
We obtained the desired fit by changing shaft tolerance