1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.
-
Upload
audra-bridges -
Category
Documents
-
view
218 -
download
0
description
Transcript of 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.
![Page 2: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/2.jpg)
2AGBell – EECT 111
2AGBell – EECT 111
CHAPTER 4
Series Circuits
![Page 3: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/3.jpg)
3AGBell – EECT 111AGBell – EECT 111
Series Circuits
• Definition: One path for current flow
• Key Characteristic: The current is the same at any point in the circuit.
![Page 4: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/4.jpg)
4AGBell – EECT 111AGBell – EECT 111
Series Circuits (cont.)
• Total resistance in a series circuit is the summation of the individual resistor values:
RT = R1 + R2 + R3 … + Rn
Where n = the number of resistors
![Page 5: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/5.jpg)
5AGBell – EECT 111AGBell – EECT 111
Series Circuits (cont.)
• Total resistance in a series circuit can also be found using Ohm’s law.
• Total resistance is equal to the circuit voltage divided by the current flowing in the circuit.
![Page 6: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/6.jpg)
6AGBell – EECT 111
6AGBell – EECT 111
Mathematical Expression
Remember, IT is the same at any point in the circuit.
T
TT I
VR
![Page 7: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/7.jpg)
7AGBell – EECT 111AGBell – EECT 111
Ohm’s Law
• The equation may also be arranged to solve for Total Voltage (VT) or Total Current (IT):
T
TTTTT R
VIRIV and
![Page 8: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/8.jpg)
8AGBell – EECT 111AGBell – EECT 111
Concept of Voltage Drop
• A voltage drop is typically thought of as a voltage produced by allowing a current to flow through a resistance.
![Page 9: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/9.jpg)
9AGBell – EECT 111AGBell – EECT 111
Voltage Drops in a Series Circuit
• The voltage drop across a resistor in a series circuit is produced from the current flow through the resistor.
![Page 10: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/10.jpg)
10AGBell – EECT 111AGBell – EECT 111
Calculating a Voltage Drop
• If there are two resistors in a series circuit, each voltage drop may be calculated by using the following equations:
VR1 = IT x R1
VR2 = IT x R2
![Page 11: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/11.jpg)
11AGBell – EECT 111AGBell – EECT 111
Voltage Divider Rule
• The voltage across any resistor in a series may be determined by using the following equation:
TT
XX V
RRV
![Page 12: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/12.jpg)
12AGBell – EECT 111AGBell – EECT 111
Term Definitions
• VX: Voltage across the desired resistor
• RX: Value of the desired resistor
• VT: The circuit applied voltage
![Page 13: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/13.jpg)
13AGBell – EECT 111AGBell – EECT 111
Kirchhoff’s Voltage Law
• An important concept used in simple to very complex circuits
• It allows one to solve problems and check answers
• Used with Ohm’s law to solve difficult problems
![Page 14: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/14.jpg)
14AGBell – EECT 111AGBell – EECT 111
Kirchhoff’s Voltage Law (cont.)
Kirchhoff’s Voltage Law (KVL) states:1. The arithmetic summation of all voltage
drops in a series circuit will always equal the applied voltage
and/or
2. The algebraic summation of the voltages around a loop will always equal zero volts
![Page 15: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/15.jpg)
15AGBell – EECT 111AGBell – EECT 111
Kirchhoff’s Voltage Law (cont.)
![Page 16: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/16.jpg)
16AGBell – EECT 111AGBell – EECT 111
Power in Series Circuits
• Remember the basic equations:
RVPRIPVIP2
2
![Page 17: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/17.jpg)
17AGBell – EECT 111AGBell – EECT 111
Power in Series Circuits (cont.)
• Because current is the same at every point in a series circuit, the resistance with the smallest value will also dissipate the smallest power value.
• The largest resistor in the circuit will dissipate the largest amount of power.
![Page 18: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/18.jpg)
18AGBell – EECT 111AGBell – EECT 111
Power in Series Circuits (cont.)
• Since the current is the same at any point in a series circuit, the equation
P = I2 x R is perhaps the best equation to use when I and R are known.
• Thus, PR1 = I2 x R1 and PR2 = I2 x R2, etc.
![Page 19: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/19.jpg)
19AGBell – EECT 111AGBell – EECT 111
Power in Series Circuits (cont.)
• The total power dissipated in a series circuit is also the amount of power the power source must deliver. This may also be expressed as:
PT = PR1 + PR2 … + PRn
![Page 20: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/20.jpg)
20AGBell – EECT 111AGBell – EECT 111
Power in Series Circuits (cont.)
• The total power may also be calculated using Watt’s law:
PT = I2 x RT
![Page 21: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/21.jpg)
21AGBell – EECT 111AGBell – EECT 111
Opens in a Series Circuit
• An open circuit occurs anytime a break in the current path occurs.
• If an open occurs at any point, current will decrease to 0 A.
• All voltage drops will decrease to 0 V.
![Page 22: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/22.jpg)
22AGBell – EECT 111AGBell – EECT 111
Opens in a Series Circuit (cont.)
• An interesting aspect of an open is that the applied voltage will appear across the open point in the circuit.
![Page 23: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/23.jpg)
23AGBell – EECT 111AGBell – EECT 111
Shorts in a Series Circuit
• A short is an undesired, very low resistance path in or around a given circuit.
• If a short occurs, current will increase because resistance decreases.
• As current increases, the voltage across the remaining resistors will increase.
![Page 24: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/24.jpg)
24AGBell – EECT 111AGBell – EECT 111
Shorts in a Series Circuit (cont.)
• If a total short occurs, RT = 0 .• Current will attempt to increase to
unacceptable levels.
![Page 25: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/25.jpg)
25AGBell – EECT 111AGBell – EECT 111
Shorts
![Page 26: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/26.jpg)
26AGBell – EECT 111AGBell – EECT 111
Multiple Voltage Sources in Series
• Series Aiding: – Negative terminal of one source is
connected to the positive terminal of the other
• Individual voltage sources add directly together:
VT = V1 + V2
![Page 27: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/27.jpg)
27AGBell – EECT 111AGBell – EECT 111
Multiple Voltage Sources in Series (cont.)
• Series Opposing: – Negative terminal of one source is connected
directly to the negative terminal of the second
• Voltage sources subtract and result is polarized in direction of the greater source:
VT = V1 – V2
![Page 28: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/28.jpg)
28AGBell – EECT 111AGBell – EECT 111
Voltage Divider
• Resistive circuits used to obtain some percentage of the applied voltage source
![Page 29: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/29.jpg)
29AGBell – EECT 111AGBell – EECT 111
Voltage Reference Points
• The concept of voltage has both magnitude and polarity.
• Specific points in a circuit to measure voltage
e.g., Vab or Vb
![Page 30: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/30.jpg)
30AGBell – EECT 111AGBell – EECT 111
Voltage Reference Points (cont.)
• The voltage measured at the first subscript notation is with respect to the second subscript.
e.g., Vab = -Vba
![Page 31: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/31.jpg)
31AGBell – EECT 111AGBell – EECT 111
Voltage Reference Points (cont.)
![Page 32: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/32.jpg)
32AGBell – EECT 111AGBell – EECT 111
Simpler Troubleshooting• Symptoms: Gather, verify and analyze• Identify: Possible areas of trouble• Make: Decisions—what, where• Perform: Tests or measurements• Locate: Narrow problem area• Examine: New location • Repeat: Procedure until problem found
![Page 33: 1 AGBell – EECT 111 1 by Andrew G. Bell (260) 481-2288 Lecture 4.](https://reader035.fdocuments.in/reader035/viewer/2022062600/5a4d1b277f8b9ab059997dcd/html5/thumbnails/33.jpg)
33AGBell – EECT 111AGBell – EECT 111
Troubleshooting Levels
• Block or module • Component• System