09 30 13 - CERAMIC TILE.pdf

MINISTRY OF HOUSING Western Sector Projects Sitework & Infrastructure OMRANIA and ASSOCIATES Project Specification

CERAMIC TILE SECTION 09 30 13 - 1

SECTION 09 30 13

CERAMIC TILES PART 1: GENERAL

1.01 SECTION INCLUDES

A. Ceramic, quarry and vitrified tiles, mortar beds and grouts including, but not limited to the following:

1. Glazed dry pressed ceramic and porcelain tiles for floors and stair treads and risers.

2. Glazed ceramic wall tiles.

3. Unglazed fully vitrified ceramic and porcelain tiles for floors.

4. Mortar beds and grouts.

5. Waterproofing.

1.02 RELATED SECTIONS

A. Section 03 30 00 Cast-in-Place Concrete.

B. Section 04 20 00 Unit Masonry.

C. Section 07 14 00 Fluid Applied Waterproofing.

D. Section 07 92 00 Joint Sealers.

E. Section 09 24 00 Portland Cement Plaster.

F. Section 10 28 13 Toilet and Bath Accessories.

1.03 REFERENCES

A. ANSI A 108.1 Installation of Ceramic Tile with Portland Cement Mortar.

B. ANSI A 108.3 Quarry Tile and Paver Tile Installed with Portland Cement Mortar.

C. ANSI A 108.4 Installation of Ceramic Tile with Organic Adhesives or Water Cleanable Tile Setting Epoxy Adhesive.

D. ANSI A 108.5 Installation of Ceramic Tile with Dry-Set Portland Cement Mortar of Latex Portland Cement Mortar or Latex Portland Cement Mortar.

E. ANSI A 108.6 Installation of Ceramic Tile with Chemical Resistant, Water Cleanable Tile Setting and Grouting Epoxy.

F. ANSI A 108.8 Installation of Ceramic Tile with Portland Chemical Resistant Furan Mortar and Grout.

G. ANSI A 108.9 Installation of Grout in Tilework.

H. ANSI A 108.10 Installation of Grout in Tilework.

I. ANSI A 118.1 Dry-Set Portland Cement Mortar.



J. ANSI A 118.3 Chemical Resistant, Water Cleanable Tile-Setting and Grouting Epoxy and Water Cleanable Tile Setting Epoxy Adhesive.

K. ANSI A 118.4 Latex-Portland Cement Mortar.

L. ANSI A 118.5 Chemical Resistant Furan Mortars and Grouts for Tile Installation.

M. ANSI A 118.6 Ceramic Tile Grouts.

N. ANSI A 118.8 Modified Epoxy Emulsion Mortar/Grout.

O. ANSI A 136.1 Organic Adhesive for Installation of Ceramic Tile.

P. ANSI A 137.1 Standard Specifications for Ceramic Tile.

Q. ANSI C 847 Metal Lath.

R. ASTM A 185 Specification for Steel Welded Wire Fabric, Plain for Concrete Reinforcement.

S. ASTM C 144 Standard Specification for Aggregate for Masonry Mortar.

T. ASTM C 150 Standard Specification for Portland Cement.

U. ASTM C 206 Standard Specification for Finishing Hydrated Line.

V. ASTM C 207 Standard Specification for Hydrated Lime for Masonry Purposes.

W. ASTM C 241 Standard Test Method for Abrasion Resistance of Stone Subjected to Foot Traffic.

X. ASTM C 503 Standard Specification for Marble Dimension Stone (Exterior).

Y. TCA Tile Council of America - Handbook for Ceramic Tile Installation.

1.04 SUBMITTALS

A. Comply with Section 01 33 00.

B. Product Data: Submit manufacturers technical information and installation instructions for materials required, except built materials.

C. Shop Drawings: Indicate tile layout, perimeter conditions, junctions with dissimilar materials, control and expansion joints, and setting details.

D. Samples for Initial Selection Purposes: Submit manufacturers charts consisting of actual tiles or sections of tile showing selected range of colors, including samples of grout and accessories involving color selection.

E. Samples for approval: Submit the following:

1. Samples for each type of tile and for each color and texture required, not less than 300 mm square or 6 tiles x 6 tiles, on plywood or hardboard backing and grouted.

2. Full size samples for each type of trim, accessory and for each color.

3. Samples of metal edge strip.

F. Certification: Furnish Master Grade Certificates for each shipment and type of tile, signed by manufacturer and installer.



1.05 MAINTENANCE DATA

A. Comply with Sections 01 77 00 and 01 78 23.

B. Maintenance Data: Include recommended cleaning methods, cleaning materials, stain removal methods and polishes and waxes.

1.06 QUALITY ASSURANCE

A. Product/Material Qualifications: ANSI A 137.1. Floor Tile Co-efficient of friction shall be not less than 0.050.

B. Perform work in accordance with latest industry standards.

C. Maintain one copy of each document on site.

D. Installer responsibility: Defective installation shall be replaced at no additional cost to Owner.

1.07 QUALIFICATIONS

A. Manufacturer: Company specializing in manufacturing the products specified in this Section with minimum 5 years experience.

B. Installer: Company specializing in performing the work of this Section minimum 5 years experience.

1.08 MOCKUP

A. Provide mockups of each type of tile system tile under provisions of Section 01 40 00.

B. Locate where directed, to include internal and external corners, bull nose tiles and junctions with floors, walls, skirtings, treads and risers.

C. Mockup shall consist of at least 1 m2

D. Mockups may not remain as part of the work.

of tile installed using specified setting method. Include grout and sealer.

1.09 DELIVERY, STORAGE, AND HANDLING


1.10 ENVIRONMENTAL REQUIREMENTS

A. Do not install adhesives in an unventilated environment.

B. Maintain minimum and maximum range of conditions recommended by manufacturer.

1.11 EXTRA MATERIALS


B. Extra Materials: Provide additional quantities, equal to 5% of the total area each type, size color and surface finish of tile installed & 15m length of each linear special (formed corners, nosings, caps etc.) Round off quantities to the next higher square meter or linear meter. Deliver extra materials to Owners on-site storage locations as coordinated with Owner.



PART 2: PRODUCTS 2.01 MATERIALS, GENERAL

A. Comply with ANSI A 137.1 for types and grades of tile indicated. Furnish tile complying with Standard Grade requirements unless otherwise indicated.

B. ANSI Standard for Tile Installation Materials: Comply with standard referenced with installation products and materials indicated.

C. Colors, Textures and Patterns: For tile and other products requiring selection of colors, surface textures or other appearance characteristics, provide products to match characteristics indicated or, if not otherwise indicated, as selected by Engineer from manufacturers standards. Provide tile and accessories which match color and finish of adjoining flat tile.

2.02 TILE PRODUCTS

A. Tiles to toilet, shower, WC & changing areas, as shown on the drawings and schedules. 1. Glazed ceramic wall tiles shall be plain colour satin finish glazed wall tiles range, or

equal approved. Tile sizes shall include 108 x 108 x 4mm or as shown to 152 x 152 x 8mm to patterns and shall include all rounded and bull nosed accessories. Unglazed exposed faces will not be allowed.

2. Unglazed Fully Vitrified Floor Tiles, as per requested range or equal approved. Tiles

sizes shall include 150 x 150 x 8mm and 300 x 300 x 8mm or as shown to patterns and shall include all coved and rounded internal and external corner skirting tiles and unfinished exposed surfaces will be allowed.

B. Glazed Ceramic Tiles: Tile sizes, patterns and finish shall be as selected by Engineer or as indicated on the Drawings, and shall include all rounded and bull nosed accessories. Unglazed exposed faces shall not be allowed. Color will be as selected by Engineer. C. Unglazed Fully Vitrified Floor Tiles: Tiles sizes and patterns shall be as selected by

Engineer or as shown on the Drawings and shall include all coved and rounded and external corner skirting tiles.

D. Non-Vitrified Body Wall Tile:

1. With smooth glazed finish:

a. Edge design: Cushion.

b. Thickness: 8 mm.

c. Size and Color: As approved by the Engineer or as shown on the Drawings.

d. Grout Color: As approved by the Engineer.

2. With smooth matt finish.

a. Edge design: Cushion.

b. Thickness: 6 mm.

c. Size and Color: As approved by the Engineer or as shown on the Drawings.



d. Grout Color: As approved by the Engineer.

E. Porcelain Paver: Matt glazed porcelain with absorption of not more than 0.5 %:

1. Edge design: Square.

2. Size: As shown on the Drawings, as approved by the Engineer.

3. Color: As shown on the Drawings, as approved by the Engineer.

4. Grout Color: As approved by the Engineer.

F. Thresholds (Saddles, Transition Strips): For mortar set installation. Size and shape to adjust between thickness of adjacent floor finish materials:

1. Material: Marble complying with ASTM C 503 requirements for exterior use and for abrasion resistance where exposed to foot traffic. Hardness not less than 10 per ASTM C 241.

2. Edge type: Beveled unless otherwise indicated.

3. Size: 22 mm thick x 50 mm wide, unless otherwise shown on the Drawings or approved by the Engineer. 13 mm maximum projection above tile floor surface.

4. Color: Match adjacent ceramic floor tile color as close as possible.

5. Exposed surfaces finish: Sand rubbed or wet sand.

G. Thresholds (Saddles, Transition Strips): For thin set installation. Size and shape to adjust between thickness of adjacent floor finish materials:

1. Material: Cast acrylic polymer.

2. Size: As shown on the Drawings or approved by the Engineer.

3. Color as shown on the Drawings or approved by the Engineer.

H. Dividing Strips: Provide as shown on the Drawings.

I. Waterproofing Membrane: Comply with Section 07 14 00.

2.03 SETTING SEALING AND GROUTING MATERIALS

A. Thin-set Portland Cement Mortar: Where thin-set Portland cement mortar applications are indicated, use the following unless otherwise required:

1. Latex-Portland cement mortar: ANSI A 118.4

2. Epoxy adhesive ANSI A 118.3

3. Organic adhesive: ANSI A 136.1

B. Mortar Materials:

1. Portland cement: ASTM C 150 Type 1.

2. Sand: ASTM C 144.

3. Lime: ASTM C 206 Type S or ASTM C 207 Type S.



4. Water: Potable.

C. Mortar Bed Installation Materials for Floors: Mortar bed: Portland cement and sand in a ratio from 1.4 to 1.5. Bond coat shall be as specified under setting method specification.

D. Mortar Bed Installation Materials for Walls: As specified in TCA Handbook for Ceramic Tile Installation for TCA setting method involved.

E. Standard Latex-Portland Cement Mortar or Bond Coat: ANSI A 118.4. Add water emulsion acrylic latex additive at project site to prepackaged dry mortar mix as per the recommendation by latex manufacturer.

F. Flexible Latex-Portland Cement Mortar or Bond Coat: Flexible latex additive added at project site to prepackaged dry mortar mix recommended by latex manufacturer.

G. Other Materials: Refer to TCA setting method specification in TCA Handbook for Ceramic Tile Installation.

H. Floor Grout: Latex-Portland cement sanded floor grout consisting of a blended mixture of Portland cement, color-fast pigments, and high strength aggregates complying with ANSI A 118.4, complete with manufacturers recommended latex additive. Grout colors shall be as indicated.

I. Wall Grout: Unsanded wall grout consisting of a blended mixture of Portland cement, color-fast pigments, and high strength aggregates complying with ANSI A 118.6.Grout colors shall be as indicated.

J. Reinforcing Mesh: Welded wire fabric, 50 x 50 mm, 1.5/1.5 mm wire, complying with ASTM A 185.

K. Metal Lath: Galvanized expanded metal lath, 18.5 kg/m2

L. Sealant in Conjunction with Tile: Provide mildew resistant silicone sealant under this Section in compliance with requirements specified under Section 07 92 00. Color shall match color of adjacent tile grout.

.

M. Trowel-Applied Waterproof Membrane for Thin-Set Installations: One-part elastomeric waterproofing membrane.

N. Crack Isolation Sheet: Composite membrane consisting of chlorinated polyethylene sheet laminated between 2 layers of non-woven polyester 0.7 mm thickness.

2.04 MISCELLANEOUS MATERIALS

A. Two-Compound Sealants: ASTM C 920, Type M, Grade P, Class 25, use T (for use in joints subject to pedestrian traffic).

B. Metal Edge Strips: Stainless steel or brass where shown, 3 mm wide at top edge with integral provision for anchorage to mortar bed or substrate, unless otherwise indicated.

C. Tile Cleaner: Product specifically acceptable to manufacturer or tile and grout manufacturer for application indicated.

PART 3: EXECUTION 3.01 EXAMINATION



A. Examine surfaces to receive tile work and conditions under which tile will be installed. Do not proceed with tile work until surfaces and conditions comply with requirements indicated in referenced tile installation standard.

3.02 PREPARATION

A. Protect surrounding work from damage or disfiguration.

B. Vacuum clean surfaces and damp clean.

3.03 INSTALLATION, GENERAL

A. Tile Installation Standards: Comply with applicable parts of ANSI 108 series of tile installation standards included under American National Standard Specifications for the Installation of Ceramic Tile.

B. Installation Guidelines: TCA Handbook for Ceramic Tile Installation; comply with TCA installation methods indicated or, if not otherwise indicated, as applicable to installation conditions shown in British Ceramic Tile Council recommendations.

C. Lay out tile so sizes less than 1/2 size are reduced to a minimum. Staggered joints are not permitted unless otherwise indicated.

D. Comply with TCA Standard Installation Specifications A108.1 through A108.10 and the TCA Handbook for Ceramic Tile Installation, except as modified herein.

E. Set individual tiles larger than 200 mm x 200 mm into setting material, taking care to maintain accurate joint alignment and spacing. Set tile to obtain 100 % contact between back of tile and setting material. Scribe and cut tile as necessary around obstructions to produce closely fitted, neat joints of uniform width throughout the installation.

F. Apply sand/cement screeds to falls to all areas to take tiled flooring to the level required for bedding. Screeds shall be poured on waterproofing membrane which shall be carried up walls and fittings and flashed up penetrations to top of skirting level.

G. Setting bed mortars, adhesives and grouts shall be of the types specified herein for the various uses. Set tile flush with adjoining units, level, true and plumb and to falls to floor drains. Grout shall be struck or tooled to the depth of the cushion. Grout in tile floors shall be flush with the surface. Remove excess grout before it has set. Install plant-mixed grout in strict accordance with the printed directions of approved manufacturer.

H. Use approved spacing gauges or other devices to obtain joints of a uniform width for wall and floor tile.

I. Replace broken, cracked, marred or otherwise defective tile or base before the setting material has set. Furnish and install corners, coves, angles or other trim shapes. Tile shall fit neatly around openings. Cutting, as far as practicable, shall be done by power saws. Cut edges shall be smooth, straight and free from chips. File hand-cut tiles or grind smooth on the cut edge.

J. Grouting of joints shall be done on the same day that tile is set.

K. Grounds, door bucks, saddles, plugs, supports and connections for mechanical or electrical work and fittings shall be in place and pipe chases and other openings shall have been properly closed before the application of tile mortar or adhesives.

L. Waterproofing, Flashing and Cove Treatment: Where vertical surfaces, including pipes, drains, walls, etc. join concrete slabs, integral flashings shall be made by coating both the



vertical and horizontal surfaces not less than 100 mm up and out from the junction. Allow to set and recoat with membrane. Treat metal flashing rings, collars, drains, etc. in the same manner. Where an isolation joint exists, follow procedures as above, and carry through as an expansion joint. Recoat as above.

M. In shower rooms, apply membrane to walls to a height of 2.1 m from finished floor level.

N. Joints and Cracks: Fill and treat joints as required by waterproofing manufacturer.

O. Priming: Prime as required by waterproofing manufacturer. Priming shall be applied over rough or porous broom finished concrete, etc., and on unpainted or unprimed metal.

P. Metal Surfaces: Apply primer appropriate for use on metal surfaces.

Q. Extend tile work into recesses and under or behind equipment and fixtures, to form a complete covering without interruptions, except as otherwise shown. Terminate work neatly at obstructions, edges and corners without disrupting pattern or joint alignments.

R. Accurately form intersections and returns. Perform cutting and drilling of tile without marring visible surfaces. Carefully grind cut edges of tile abutting trim, finish or build-in items for straight aligned joints. Fit tile closely to electrical outlets, piping, fixtures and other penetrations so that plates, collars or covers overlap tile.

S. Jointing Pattern: Unless otherwise shown, lay tile in grid pattern. Align joints when adjoining tiles on floor, base, walls and trim are same size. Layout tile work and center tile fields in both directions in each space or on each wall area. Adjust to minimize tile cutting. Provide uniform joint width, unless otherwise shown.

T. Expansion Joints: Locate expansion joints and other sealant filled joints, including control, contraction and isolation joints, where indicated, or if not indicated, at spacings and locations recommended in TCA "Handbook for Ceramic Tile Installation" and approved by the Engineer. Prepare joints and apply sealants to comply with requirements of referenced standards and sealant manufacturer.

U. Grout tile to comply with referenced installation standards, using grout materials indicated. Mix and install proprietary components to comply with grout manufacturer's directions.

V. Finished Appearance: Ensure that entire surfaces appear consistent in colour, tone, pattern and jointing upon completed installation. Replace any tiles that do not match the surrounding area.

W. Repair/redo defective tiling work as directed by the Engineer.

3.04 INSTALLATION METHODS

A. Specific revisions and limited altering of TCA recommendations:

1. Dry-set mortar is not acceptable where included as an option under the following TCA setting methods.

2. Flexible Latex-Portland Cement Mortar/Bond Coat is required instead of Standard Latex-Portland Cement Mortar or Bond Coat for installation of quarry and porcelain tile under the following TCA setting methods requiring latex-Portland cement mortar or latex-Portland cement bond coats.

B. TCA F111 Floor Setting Method: 31 mm cement mortar setting bed with reinforcing mesh over cleavage membrane. Setting Method Location: Where tile occurs at depressed areas of concrete floors above grade, unless indicated otherwise.



C. TCA F112 Floor Setting Method: 19 mm to 31 mm mortar set application over concrete substrate. Use latex Portland cement mortar bed with latex Portland cement bond coat. Setting Method Location: Where tile occurs at depressed areas of concrete slabs on grade, unless indicated otherwise.

D. TCA F113 Floor Setting Method (Modified): Thin-set application using latex Portland cement mortar feather as necessary to provide smooth transition at adjoining finished floor elevation. Setting Method Location: Where tile occurs on concrete floors where no depressions occur and where tapered transitions are required to meet adjacent floor finishes.

E. TCA F121 Floor Setting Method: 31 mm cement mortar setting bed bonded to concrete substrate. Setting Method Location: Where tile occurs at depressed areas of concrete floors and a waterproof membrane is indicated.

F. TCA F122 Floor Setting Method: Thin-set with latex-Portland cement mortar bond coat over waterproof membrane. Setting Method Location: Where tile occurs on concrete floors where no depressions occur, and a waterproof membrane is indicated.

G. TCA F131 Floor Setting Method: Thin-set with epoxy mortar bond coat over concrete substrate. Setting Method Location: Where quarry tile occurs on concrete floors in kitchen areas where no depressions occur, unless indicated otherwise.

H. TCA F132 Floor Setting Method: 31 mm Portland cement mortar bed with epoxy bond coats. Setting Method Location: Where quarry tile occurs on concrete floors where depressions occur, unless indicated otherwise.

I. TCA W202 Wall Setting Method: Thin-set with latex Portland cement mortar bond coat over concrete or masonry backup. Setting Method Location: Where tile occurs on smooth masonry or concrete walls unless indicated otherwise.

J. TCA W211 Wall Setting Method Directly over Concrete or Concrete Block: Leveling coat over masonry or concrete backup with latex Portland cement bond coat. Setting Method Location: Where tile occurs on rough masonry or concrete walls unless indicated otherwise.

K. TCA W241 Wall Setting Method: 19 mm to 25 mm mortar set over metal studs. Setting Method Location: Where tile occurs on walls over metal studs or furring in showers.

L. A W243 Wall Setting Method: Thin-set with latex Portland cement mortar bond coat over gypsum wallboard and wood or metal studs. Setting Method Location: Where tile occurs on walls over gypsum board in dry areas unless indicated otherwise.

M. TCA W244 Wall Setting Method at Portland Cement Board: Thin-set with latex Portland cement mortar bond coat over Portland cement board and wood or metal studs. Setting Method Location: Where tile occurs on walls over Portland cement backer board (TBB) in wet areas unless indicated otherwise.

N. TCA B411 Wall Setting Method at Bath Tubs: 19 mm to 31 mm mortar setting bed reinforced with galvanized metal lath applied over waterproof membrane. Setting Method Location: Where tile occurs on walls surrounding bath tubs unless indicated otherwise.

O. TCA B415 Shower Area Combination Floor and Wall Setting Method:

1. Walls: Thin set with latex modified Portland cement bond coat applied over Portland cement backer board and studs.



2. Floor/shower basin: 25 mm to 38 mm mortar setting bed with 50 mm x 50 mm reinforcing mesh installed over waterproof membrane or pan. Waterproof membrane as specified in Section 07 14 00.

3. Setting method location: Where tile occurs in showers unless indicated otherwise.

3.05 CLEANING AND PROTECTION


B. Cleaning: Upon completion of placement of grouting, clean all ceramic tile surfaces so they are free from foreign matter.

1. Unglazed tile may be cleaned with acid solutions only when permitted by tile and grout manufacturer's printed instructions, but no sooner than 14 days after installation. Protect metal surfaces, cast iron and vitreous plumbing fixtures from effects of acid cleaning. Flush surface with clean water before and after cleaning.

2. Apply quarry tile filler to clean, dry quarry tiles in compliance with filler manufacturer's directions. Repeat application as necessary to obtain uniform color in appearance of both tile and grout.

C. Finish Tile Work: Leave finished installation clean and free of cracked, chipped, broken, unbonded or otherwise defective tile work.

D. Protection: When recommended by tile manufacturer, apply a protective coat of neutral protective cleaner to completed tile walls and floors. Protect installed tile work with draft paper or other heavy covering during construction period to prevent staining, damage and wear.

E. Prohibit foot and wheel traffic from using tiled floor at least 7 days after grouting is completed.

F. Before final inspection, remove protective coverings and rinse neutral cleaning from tile surface.

END OF SECTION

SECTION 09 30 13CERAMIC TILESPART 1: GENERALPART 2: PRODUCTSPART 3: EXECUTIONEND OF SECTION

09 30 13 - CERAMIC TILE.pdf

Documents

Transcript of 09 30 13 - CERAMIC TILE.pdf