07.01.2015_16.14.23_369330.pdf
-
Upload
solange-ferrari -
Category
Documents
-
view
235 -
download
0
Transcript of 07.01.2015_16.14.23_369330.pdf
-
INSERT & TOOLS
-
2b ap
R
rs
Insert type R(mm)
ap (Max.)(mm)
b r(mm)
s(mm)
t(mm)
R1(mm)
WNMX 130520-M1 6.35 2.0 40 2.0 5.56 0.8 3.0
t
R1
Nose- R . Security of rigid edge in ramping, pocket machining
. Round edge line suitable for high feed
. Insert geometry extrinsic to R/L type machining
Minor cutting edge . Improvement of surface roughness
. Desgn for decreasing thrust force
Major cutting edge . High feed by application of high rake cutting edge
. Realization of low cutting resistace in high feed
Chip breaker . Reduction of cutting load due to high rake angle
INSERTWNMX 130520-M1
Insert type GRADEK (K20-K40) M (M20-M30) P (P15-P30)
Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev)
WNMX 130520-M1 GT30CN - - 120 0.8-1.3 180 1.0-2.0
Cutting Parameters
-
3AL
E
D
L
B
a
ap
Type Nr.ofinserts
D(mm)
L(mm)
AL(mm)
E(mm)
a(mm)
B(mm)
ap(mm)
WN13/050-04-AL22-L40-R 4 50 40 22 20 6.3 10.4 2
WN13/052-04-AL22-L40-R 4 52 40 22 20 6.3 10.4 2
WN13/063-05-AL22-L40-R 5 63 40 22 20 6.3 10.4 2
SHELL MILL
Accessories
Insert Type Screw Screw Size Wrench
WNMX 130520-M1 CS-WN13 M5.0 W-WN13
-
4 Type Nr.ofinserts
D(mm)
L(mm)
d(mm)
L1(mm)
M(mm)
MD(mm)
E(mm)
ap(mm)
WN13/042-03-M16-L40-R 3 42 40 17 23 16 29 22 2
L L1
MD M
E
d
ap
D
END MILL (SCREW-ON)
Accessories
Insert Type Screw Screw Size Wrench
WNMU 13 .. .. CS-WN13 M5.0 W-WN13
-
5 Type Nr.ofinserts
D(mm)
L(mm)
L1(mm)
d(mm)
ap(mm)
WN13/033-02-QCC32-L200-R 2 33 200 50 32 2
WN13/040-03-QCC32-L250-R 3 40 250 50 32 2
L1
L
d
ap
D
END MILL (CYLINDIRACAL SHANK)
Accessories
Insert Type Screw Screw Size Wrench
WNMU 13 .. .. CS-WN13 M5.0 W-WN13
-
6s h
L
r
d
Insert type s(mm)
h(mm)
d(mm)
r(mm)
L(mm)
GNMU 110605ZZR-M1 6.63 7.0 3.80 0.5 11.0
GNMU 161008ZZR-M1 9.96 11.5 5.40 0.8 15.5
90
Nose- R . Security of rigid edge in ramping, pocket machining
Chip breaker . Reduction of cutting load due to high rake angle
INSERT
GNMU 110605ZZR-M1
Insert type GRADEK (K20-K40) M (M20-M30) P (P15-P30)
Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev)
GNMU 110605ZZR-M1 GT30CN - - 140 0.05-0.25 210 0.05-0.25
GNMU 161008ZZR-M1 GT30CN - - 140 0.05-0.25 210 0.05-0.25
Cutting Parameters
Available 4 cutting edges to save the tool cost
-
7 Type Nr.ofinserts
D(mm)
L(mm)
AL(mm)
E(mm)
a(mm)
B(mm)
ap(mm)
GN11/040-05-AL16-L40-R 5 40 40 16 18 5.6 8.2 10
GN11/050-06-AL22-L40-R 6 50 40 22 20 6.3 10.4 10
GN11/063-07-AL22-L40-R 7 63 40 22 20 6.3 10.4 10
GN11/080-08-AL27-L50-R 8 80 50 27 22 7 12.4 10
GN11/100-09-AL32-L50-R 9 100 50 32 29 8 14.4 10
GN16/050-04-AL22-L40-R 4 50 40 22 20 6.3 10.4 14
GN16/063-06-AL22-L40-R 6 63 40 22 20 6.3 10.4 14
GN16/080-07-AL27-L50-R 7 80 50 27 22 7 12.4 14
GN16/100-08-AL32-L50-R 8 100 50 32 29 8 14.4 14
SHELL MILL
AL
E
L
B
a
ap
D
Accessories
Insert Type Screw Screw Size Wrench
GNMU 110605ZZR-M1 CS-GN11 M3.0 W-GN11
GNMU 161008ZZR-M1 CS-GN16 M5.0 W-GN16
-
8 Type Nr.ofinserts
D(mm)
L(mm)
d(mm)
L1(mm)
M(mm)
MD(mm)
E(mm)
ap(mm)
GN11/020-02-M10-L30-R 2 20 35 10.5 22 10 18 15 10
GN11/025-03-M12-L30-R 3 25 35 12.5 22 12 21 18 10
GN11/032-04-M16-L40-R 4 32 40 17 23 16 29 22 10
GN11/042-05-M16-L40-R 5 42 40 17 23 16 29 22 10
L L1
E
M MD
d
ap
D
END MILL (SCREW-ON)
Accessories
Insert Type Screw Screw Size Wrench
GNMU 11.. .. CS-GN11 M3.0 W-GN11
-
9L1
L
D
ap
d
Type Nr.ofinserts
D(mm)
L(mm)
L1(mm)
d(mm)
ap(mm)
GN11/020-02-QCC20-L140-R 2 20 140 40 20 10
GN11/025-03-QCC25-L140-R 3 25 140 45 25 10
GN11/032-04-QCC32-L140-R 4 32 140 50 32 10
GN16/032-02-QCC25-L140-R 2 25 140 45 25 14
GN16/040-03-QCC32-L140-R 3 32 140 50 32 14
END MILL (CYLINDIRACAL SHANK)
Accessories
Insert Type Screw Screw Size Wrench
GNMU 110605ZZR-M1 CS-GN11 M3.0 W-GN11
GNMU 161008ZZR-M1 CS-GN16 M5.0 W-GN16
-
10
s
d
h
L
r
Insert type s (mm)
ap (Max.)(mm)
b r(mm)
h(mm)
L(mm)
d(mm)
ONMU 060508-M1 5.60 4.0 45 0.8 16 16 5.4
b
90
ap
Nose- R . Security of rigid edge in ramping, pocket machining
. Round edge line suitable for high feed
. Insert geometry extrinsic to R/L type machining
Chip breaker . Reduction of cutting load due to high rake angle
INSERT
ONMU 060508-M1
Insert type GRADEK (K20-K40) M (M20-M30) P (P15-P30)
Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev)
ONMU 060508-M1 GT30CN - - 150 0.10-0.35 180 0.10-0.35
Cutting Parameters
Available 16 cutting edges to save the tool cost
-
11
AL
E
B
D
L
a
ap
Type Nr.ofinserts
D(mm)
L(mm)
AL(mm)
E(mm)
a(mm)
B(mm)
ap(mm)
ON06/063-05-AL22-L40-R 5 63 40 22 20 6.3 10.4 4
ON06/080-06-AL27-L50-R 6 80 50 27 22 7 12.4 4
ON06/100-07-AL32-L50-R 7 100 50 32 25 8 14.4 4
ON06/125-08-AL40-L63-R 8 125 63 40 30 9 16.4 4
ON06/160-10-AL40-L63-R 10 160 63 40 32 9 16.4 4
ON06/160-10-AL40-L63-L 10 160 63 40 32 9 16.4 4
ON06/200-12-AL60-L63-R 12 200 63 60 32 14 25.7 4
ON06/200-12-AL60-L63-L 12 200 63 60 32 14 25.7 4
SHELL MILL
Accessories
Insert Type Screw Screw Size Wrench
ONMU 060508-M1 CS-ON06 M5.0 W-ON06
-
12
s
d L
h
r
Insert type s(mm)
ap (Max.)(mm)
d(mm)
r(mm)
h(mm)
L(mm)
t(mm)
SNMU 12 .. .. 6.3 6.0 5.0 0.4 12 12 2.17
45
t
b
ap
Minor cutting edge . Improvement of surface roughness
. Desgn for decreasing thrust force
Major cutting edge . High feed by application of high rake cutting edge
. Realization of low cutting resistace in high feed
Chip breaker . Reduction of cutting load due to high rake angle
INSERT
Insert type GRADEK (K20-K40) M (M20-M30) P (P15-P30)
Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev)
SNMU 1206ANTN-M1 GT30CN - - 150 0.10-0.35 220 0.10-0.25
Cutting Parameters
SNMU 1206ANTN-M1
Available 8 cutting edges to save the tool cost
-
13
Type Nr.ofinserts
D(mm)
L(mm)
AL(mm)
E(mm)
a(mm)
B(mm)
ap(mm)
SN12/050-05-AL22-L40-R 5 50 40 22 20 6.3 10.4 6
SN12/063-06-AL22-L40-R 6 63 40 22 20 6.3 10.4 6
SN12/080-07-AL27-L50-R 7 80 50 27 22 7 12.4 6
SN12/100-08-AL32-L50-R 8 100 50 32 25 8 14.4 6
SN12/125-10-AL40-L63-R 10 125 63 40 30 9 16.4 6
SN12/160-12-AL40-L63-R 12 160 63 40 32 9 16.4 6
SN12/160-12-AL40-L63-L 12 160 63 40 32 9 16.4 6
SN12/200-14-AL60-L63-R 14 200 63 60 32 14 25.7 6
SN12/200-14-AL60-L63-L 14 200 63 60 32 14 25.7 6
SN12/250-16-AL60-L63-R 16 250 63 60 32 14 25.7 6
SN12/250-16-AL60-L63-L 16 250 63 60 32 14 25.7 6
SHELL MILL
Accessories
Insert Type Screw Screw Size Wrench
SNMU 1206ANTN-M1 CS-SN12 M5.0 W-SN12
-
14
s h
Ld
r
Insert type L(mm)
ap (Max.)(mm)
h(mm)
r(mm)
s(mm)
d(mm)
SNKU 08 03 08 8.70 7.0 8.70 0.8 3.72 5.0
90
ap
Chip breaker . Reduction of cutting load due to high rake angle
INSERT
Insert type GRADEK (K20-K40) M (M20-M30) P (P15-P30)
Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev)
SNKU 08 03 08 GT30CN - - 150 0.10-0.35 220 0.10-0.25
Cutting Parameters
SNKU 08 03 08
Available 8 cutting edges to save the tool cost
-
15
D
L
L1
d
Type Nr.ofinserts
D(mm)
L(mm)
L1(mm)
d(mm)
ap(mm)
SNX08/025-03-QC25-L140-R 3 25 140 60 25 5.0
SNX08/032-04-QC32-L140-R 4 32 140 60 32 5.0
SNX08/040-05-QC32-L140-R 5 40 140 80 32 5.0
END MILL (CYLINDIRACAL SHANK)
AL
a
B
E
L
D
Type Nr.ofinserts
D(mm)
L(mm)
AL(mm)
E(mm)
a(mm)
B(mm)
ap(mm)
SNX08/040-05-AL16-L40-R 5 40 40 16 18 5.6 8.2 5.0
SNX08/050-06-AL22-L40-R 6 50 40 22 20 6.3 10.4 5.0
SNX08/063-08-AL22-L40-R 8 63 40 22 20 6.3 10.4 5.0
Accessories
Insert Type Screw Screw Size Wrench
SNKU 08 03 08 ST3083-60 M3.0 / T9 FT-T09
SHELL MILL
-
16
s R
b
Insert type R(mm)
b s(mm)
ap(mm)
RDMW 1003MO 10.0 15 3.18 10
RDMW 12T3MO 12.0 15 3.97 12
RDMW 1604MO 16.0 15 4.76 16
INSERT
Insert type GRADEK (K20-K40) M (M20-M30) P (P15-P30)
Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev)
RDMW 1003MO GT30CN 180 0.30-0.60 130 0.20-0.35 170 0.30-0.60
RDMW 12T3MO GT30CN 180 0.30-0.60 130 0.20-0.35 170 0.30-0.60
RDMW 1604MO GT30CN 180 0.30-0.60 130 0.20-0.35 170 0.30-0.60
Cutting Parameters
RDMW 10-12-16
-
17
Type Nr.ofinserts
D(mm)
L(mm)
AL(mm)
E(mm)
a(mm)
B(mm)
ap(mm)
RD10/040-05-ALC16-L40-R 5 40 40 16 18 5.6 8.2 5
RD10/050-06-ALC22-L40-R 6 50 40 22 20 6.3 10.4 5
RD10/063-07-ALC22-L40-R 7 63 40 22 20 6.3 10.4 5
RD12/040-04-ALC16-L40-R 4 40 40 16 18 5.6 8.2 6
RD12/050-04-ALC22-L40-R 4 50 40 22 20 6.3 10.4 6
RD12/050-05-ALC22-L40-R 5 50 40 22 20 6.3 10.4 6
RD12/052-04-ALC22-L40-R 4 52 40 22 20 6.3 10.4 6
RD12/052-05-ALC22-L40-R 5 52 40 22 20 6.3 10.4 6
RD12/063-06-ALC22-L40-R 6 63 40 22 20 6.3 10.4 6
RD12/066-06-ALC27-L50-R 6 66 50 27 22 7 12.4 6
RD16/052-04-ALC22-L50-R 4 52 50 22 20 6.3 10.4 8
RD16/063-05-ALC27-L50-R 5 63 50 27 22 7 12.4 8
RD16/066-05-ALC27-L50-R 5 66 50 27 22 7 12.4 8
RD16/080-06-ALC27-L50-R 6 80 50 27 22 7 12.4 8
RD16/100-07-ALC32-L50-R 7 100 50 32 32 8 14.4 8
SHELL MILL
Accessories
Insert Type Screw Screw Size Wrench
RDMW 1003MO CS-1046226 M3.5 / 15 IP TP-925858
RDMW 12T3MO CS-1046226 M3.5 / 15 IP TP-925858
RDMW 1604MO CS-731949 M5.0 / 20 IP TP-925859
-
18
Type Nr.ofinserts
D(mm)
d(mm)
L(mm)
L1(mm)
M(mm)
MD(mm)
E(mm)
ap(mm)
RD10/020-02-M10-L25-R 2 20 10.5 25 20 M10 18 12 5
RD10/025-03-M12-L30-R 3 25 12.5 30 22 M12 23 20 5
RD10/032-03-M16-L40-R 3 32 17 40 23 M16 29 25 5
RD10/042-05-M16-L40-R 5 42 17 40 23 M16 29 25 5
RD12/025-02-M12-L30-R 2 25 12.5 30 22 M12 23 20 6
RD12/032-03-M16-L40-R 3 32 17 40 23 M16 29 25 6
RD12/042-04-M16-L40-R 4 42 17 40 23 M16 29 25 6
END MILL (SCREW-ON)
Accessories
Insert Type Screw Screw Size Wrench
RDMW 1003MO CS-1046226 M3.5 / 15 IP TP-925858
RDMW 12T3MO CS-1046226 M3.5 / 15 IP TP-925858
RDMW 1604MO CS-731949 M5.0 / 20 IP TP-925859
-
19
Type Nr.ofinserts
D(mm)
L(mm)
L1(mm)
d(mm)
ap(mm)
RD10/020-02-QCC20-L200-R 2 16 200 40 20 5
RD10/020-02-QCC25-L250-R 2 16 250 40 25 5
RD10/025-03-QCC32-L250-R 3 20 250 80 32 5
RD10/032-04-QCC32-L250-R 4 20 250 60 32 5
RD12/025-02-QCC25-L250-R 2 21 250 60 25 6
RD12/032-03-QCC32-L250-R 3 21 250 60 32 6
RD16/032-02-QCC32-L250-R 4 32 250 60 32 8
END MILL (CYLINDIRACAL SHANK)
Accessories
Insert Type Screw Screw Size Wrench
RDMW 1003MO CS-1046226 M3.5 / 15 IP TP-925858
RDMW 12T3MO CS-1046226 M3.5 / 15 IP TP-925858
RDMW 1604MO CS-731949 M5.0 / 20 IP TP-925859
-
20
Insert type GRADEK (K20-K40) M (M20-M30) P (P15-P30)
Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev) Vc(mm/min) fz (mm/Rev)
XTNJ-20 GT30C - - - - 110-200 0.05-0.12
XTRJ-20-6D GT30C - - - - 110-200 0.05-0.12
XTLJ-20-6D GT30C - - - - 110-200 0.05-0.12
XTNJ-20 GT35P - - 60-150 0.05-0.12 - -
XTRJ-20-6D GT35P - - 60-150 0.05-0.12 - -
XTLJ-20-6D GT35P - - 60-150 0.05-0.12 - -
XTNJ-30 GT30C - - - - 110-200 0.05-0.12
XTRJ-30-6D GT30C - - - - 110-200 0.05-0.12
XTLJ-30-6D GT30C - - - - 110-200 0.05-0.12
XTNJ-30 GT35P - - 60-150 0.05-0.12 - -
XTRJ-30-6D GT35P - - 60-150 0.05-0.12 - -
XTLJ-30-6D GT35P - - 60-150 0.05-0.12 - -
XTNJ-40 GT30C - - - - 110-200 0.05-0.12
Cutting Parameters
INSERT
s
L
r
Insert type L(mm)
r(mm)
s(mm)
XTNJ-20 20 0.2 2.0
XTRJ-20-6D 20 0.2 2.0
XTLJ-20-6D 20 0.2 2.0
XTNJ-30 20 0.2 2.0
XTRJ-30-6D 20 0.2 3.0
XTLJ-30-6D 20 0.2 3.0
XTNJ-40 20 0.2 4.0
XTNJ - XTRJ- XTLJ
-
21
KIT01 R/L External
bf
L2
L1
P
h
S
h1
f
l2
ar
l1
Toolholder Type h(mm)
b(mm)
P(mm)
L1(mm)
L2(mm)
S(mm)
GT-KIT01R/L 1212K S20 P10 12 12 10 125 26 2,0
GT-KIT01R/L 1212K S20 P14 12 12 14 125 30 2,0
GT-KIT01R/L 1212K S20 P17 12 12 17 125 34 2,0
GT-KIT01R/L 1616K S20 P14 16 16 14 125 32 2,0
GT-KIT01R/L 1616K S20 P17 16 16 17 125 34 2,0
GT-KIT01R/L 2020K S20 P10 20 20 10 125 26 2,0
GT-KIT01R/L 2020K S20 P14 20 20 14 125 32 2,0
GT-KIT01R/L 2020K S20 P17 20 20 17 125 34 2,0
GT-KIT01R/L 2525M S20 P10 25 25 10 150 26 2,0
GT-KIT01R/L 2525M S20 P14 25 25 14 150 32 2,0
GT-KIT01R/L 2525M S20 P17 25 25 17 150 34 2,0
GT-KIT01R/L 1212K S30 P10 12 12 10 125 26 3,0
GT-KIT01R/L 1212K S30 P14 12 12 14 125 30 3,0
GT-KIT01R/L 1212K S30 P17 12 12 17 125 34 3,0
GT-KIT01R/L 1616K S30 P14 16 16 14 125 32 3,0
GT-KIT01R/L 1616K S30 P17 16 16 17 125 34 3,0
GT-KIT01R/L 2020K S30 P10 20 20 10 125 26 3,0
GT-KIT01R/L 2020K S30 P14 20 20 14 125 32 3,0
GT-KIT01R/L 2020K S30 P17 20 20 17 125 34 3,0
GT-KIT01R/L 2525M S30 P10 25 25 10 150 26 3,0
GT-KIT01R/L 2525M S30 P14 25 25 14 150 32 3,0
GT-KIT01R/L 2525M S30 P17 25 25 17 150 34 3,0
GT-KIT01R/L 1212K S40 P10 12 12 10 125 26 4,0
GT-KIT01R/L 1212K S40 P14 12 12 14 125 30 4,0
GT-KIT01R/L 1212K S40 P17 12 12 17 125 34 4,0
GT-KIT01R/L 1616K S40 P14 16 16 14 125 32 4,0
GT-KIT01R/L 1616K S40 P17 16 16 17 125 34 4,0
GT-KIT01R/L 2020K S40 P10 20 20 10 125 26 4,0
GT-KIT01R/L 2020K S40 P14 20 20 14 125 32 4,0
GT-KIT01R/L 2020K S40 P17 20 20 17 125 34 4,0
GT-KIT01R/L 2525M S40 P10 25 25 10 150 26 4,0
GT-KIT01R/L 2525M S40 P14 25 25 14 150 32 4,0
GT-KIT01R/L 2525M S40 P17 25 25 17 150 34 4,0
Toolholder type Size Clamp Screw Key for Clamp Screw
12 x 12 / 16 x 16 CS-GT1216 K-GT1216
20 x 20 / 25 x 25 CS-GT2025 K-GT2025
Accessories
-
22
KIT01 R/L Internal
f
h
h/2
Dmin d
L1
p
L
S
2
Toolholder Type Dmin(mm)
p(mm)
f(mm)
L1(mm)
L2(mm)
h(mm)
d(mm)
S(mm)
GT-S20R KIT01R/L S20 P7 25 7 13 40 200 18 20 2,0
GT- S20R KIT01R/L S30 P7 25 7 13 40 200 18 20 3,0
GT-S25R KIT01R/L S20 P10 32 10 17 50 200 23 25 2,0
GT-S25R KIT01R/L S30 P10 32 10 17 50 200 23 25 3,0
GT-S25R KIT01R/L S40 P10 32 10 17 50 200 23 25 4,0
GT-S32S KIT01R/L S20 P12 40 12 22 64 250 30 32 2,0
GT-S32S KIT01R/L S30 P12 40 12 22 64 250 30 32 3,0
GT-S32S KIT01R/L S40 P12 40 12 22 64 250 30 32 4,0
GT-S32S KIT01R/L S50 P16 44 16 26 64 250 30 32 5,0
GT-S40T KIT01R/L S40 P16 52 16 30 80 300 38 40 4,0
GT-S40T KIT01R/L S50 P16 52 16 30 80 300 38 40 5,0
GT-S40T KIT01R/L S60 P16 52 16 30 80 300 38 40 6,0
Toolholder type Size Clamp Screw Key for Clamp Screw
d - 20 CS-GTS20 K-GTS20
d - 20 - 32 CS-GTS2532 K-GTS2532
d - 40 CS-GTS40 K-GTS40
Accessories
-
23
KIT01 R/L External
Toolholder Type h b L1 L2 Dmax S
GT-KIT01R/L 1616K S30 D42 16 16 125 34 42 3
GT-KIT01R/L 2020K S30 D42 20 20 125 35 42 3
GT-KIT01R/L 2525M S30 D42 25 25 150 35 42 3
GT-KIT01R/L 2020K S30 D56 20 20 125 45 56 3
GT-KIT01R/L 2525M S30 D56 25 25 150 45 56 3
hh
Dmax
b
LL2
1
Toolholder type Size Clamp Screw Key for Clamp Screw
16 x 16 / 20 x20 / 25 x 25 CS-GT2025 K-GT2025
Accessories
-
24
NOTE
-
25
NOTE
-
Man Office :Imes San Sit E Blk 504 SkNo:1 Umraniye 34776Istanbul-Turkey Tel:+90 216 314 18 96Fax:+90 216 314 20 [email protected]
Factory :Organize San. Blgesi 4. Cadde No:4 Umraniye 34776Istanbul-Turkey Tel:+90 216 420 87 89Fax:+90 216 420 87 88
Rami Branch :Topcular Ksla Cd.Apek Uretmen No:89/A135 RamiIstanbul-Turkey Tel:+90 212 544 97 29Fax:+90 212 613 17 [email protected]
Bursa Branch :Parkop Parcaclar San Sit48 Sk No 56Bursa-TurkeyTel:+90 224 441 75 19Fax:+90 224 441 76 [email protected]
Ankara Branch :Ahievran Cd Gelisim Is Merkezi N:18-53 OstimAnkara-Turkey Tel:+90 312 386 30 12Fax:+90 312 386 30 [email protected]
Konya Branch :Fevzi Cakmak Mh10642. Sk No:21 42052 KaratayKonya-Turkey Tel:+90 332 345 29 85Fax:+90 312 386 30 [email protected]
Germany Branch:G-Tech Europe Mrikestr.175387 Neubulach- Germany Tel:+49 7053 96 84 16Tel:+49 7053 96 84 [email protected]
Authorized dealer:Sur Teknik Hrdavat Ltd. ti.Rami Kla Cad. Eminta Aktoker San. Sit.No:89 Topular - stanbul /Turkey Tel +90 212 564 21 57 Fax:+90 212 418 10 80e mail:[email protected]
www.g-tech.com.tr
-
www.g-tech.com.tr