632 South 3rd StreetP.O. Box 2816 � Paducah, KY 42002Phone: 270-444-0085Fax:270-443-6180Website: www.matweld.comEmail: customerservice@matweld.com

The Matweld Weld Shear is lightweightand highly efficient. Spring centered flowcontrol valve permits safe and preciseshearing of a Thermite weld. The shieldtotally protects fittings and hoses. Theadjustable hold downs are self lockingand will assure a safe clean cut.

05100A WELD SHEAR

A

C

B

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

FLOW

5 gpm(19 lpm)

PRESSURE

2000 psi(140 bar)

DIMENSIONS

A - 27"B -20"C - 13"

WEIGHT

98 lbs(44.54 kg)

2

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

3

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

GENERAL SAFETY PRECAUTIONS:TOOL OPERATORS AND MAINTENANCE PERSONNEL MUST ALWAYS COMPLY WITH THESAFETY PRECAUTIONS GIVEN IN THIS MANUAL, AND WITH ALL STICKERS AND TAGS AT-TACHED TO THE TOOL AND HOSE. ALL SAFETY PRECAUTIONS ARE GIVEN FOR YOUR SAFETY.READ TO UNDERSTAND AND FOLLOW ALL SAFETY, MAINTENANCE AND OPERATION IN-STRUCTIONS BEFORE YOU USE OR MAINTAIN THE TOOL. REVIEW THE MANUAL DAILY BE-FORE USING THE TOOL. IN ADDITION, FOLLOW ALL SAFETY GUIDELINES GIVEN YOU BYYOUR SUPERVISOR. DO NOT USE THE TOOL IF YOU HAVE ANY QUESTIONS ABOUT THEOPERATION, SAFETY OR MAINTENANCE OF THIS TOOL. FAILURE TO FOLLOW THESE IN-STRUCTIONS CAN RESULT IN PERSONAL INJURY OR EQUIPMENT DAMAGE.MATWELD HAS NO CONTROL OVER TOOL USE OR OPERATION ONCE IT LEAVES THEMATWELD PLANT. MATWELD HAS NO CONTROL OVER OPERATOR OR MAINTAINER SELEC-TION. THE CUSTOMER MUST ASSUME RESPONSIBILITY FOR THE TOOL�S SUITABILITY FORA PARTICULAR FUNCTION, FOR ANYONE USING THE TOOL OR MAINTAINING THE TOOL RE-GARDING THEIR FITNESS TO USE THE TOOL OR REPAIR THE TOOL, UNDERSTANDING OFTHE OPERATION AND SAFETY AND MAINTENANCE MANUAL, INTELLIGENCE TO USE GOODJUDGMENT NECESSARY TO WORK SAFELY AND EFFICIENTLY WITHOUT ENDANGERINGTHEMSELVES OR BYSTANDERS IN THE WORK AREA.� DO NOT OPERATE THE TOOL UNTIL YOU HAVE BEEN THOROUGHLY AND PROPERLY

TRAINED OR UNDER THE SUPERVISION OF AN INSTRUCTOR.� CHECK POWER SOURCE DAILY TO DETERMINE IF CORRECT FLOW AND PRESSURE ARE

AVAILABLE. NEVER EXCEED FLOWS OR PRESSURES FOR THE TOOL BEING USED. PER-SONAL INJURY OR DAMAGE TO THE TOOL CAN RESULT.

� OPERATORS MUST CLEAR THE WORK AREA OF NON-ESSENTIAL PERSONNEL. FLYINGDEBRIS CAN CAUSE SERIOUS INJURY.

� THE OPERATOR MUST BE FAMILIAR WITH ALL PROHIBITED WORK AREAS SUCH AS UN-SAFE GRADES, POOR FOOTING AREAS AND OVERHEAD HAZARDS.

� MAINTAIN BALANCE AND PROPER FOOTING AT ALL TIMES. NEVER OVERREACH TO THEEXTENT THAT A BROKEN PART OR SUDDEN MOVEMENT OF THE TOOL CAN CAUSE YOUTO LOSE YOUR BALANCE AND FALL, OR CAUSE INJURY TO YOUR SELF OR SOMEONEELSE.

4

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

� WHEN WORKING NEAR ELECTRICAL CONDUCTORS, ALWAYS ASSUME THAT THE CON-DUCTORS ARE ENERGIZED AND THAT HOSES AND CLOTHING CAN CONDUCT HARMFULELECTRICITY. USE HOSES LABELED AND CERTIFIED AS NON-CONDUCTIVE.

� DO NOT OPERATE THE TOOL AT EXCESSIVE FLUID TEMPERATURES OPERATOR DIS-COMFORT AND POTENTIAL BURNS CAN RESULT AT HIGH OIL TEMPERATURES.

� NEVER WEAR LOOSE CLOTHING THAT CAN GET ENTANGLED IN THE WORKING PARTSOF THE TOOLS OR BE CARELESS WITH HANDS, FEET OR OTHER BODY PARTS AROUNDTHE WORKING PARTS OF THE TOOLS. HYDRAULIC TOOLS EXERT HIGH TORQUE ANDFORCE AND CAN CAUSE SERIOUS INJURY OR DEATH IF IMPROPERLY USED.

� TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL REPAIR, MAINTENANCEOR SERVICE MUST ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY TRAINEDPERSONNEL.

� ALWAYS WEAR SAFETY EQUIPMENT SUCH AS OIL INJECTION RESISTANT WORK GLOVES,SAFETY GLASSES, SAFETY BOOTS, EAR PROTECTION AND OTHER SAFETY APPARELDICTATED BY YOUR SUPERVISOR APPLICABLE FOR THE JOB YOU ARE DOING AND THETOOL YOU ARE USING.

� DO NOT CLEAN INSPECT OR REPAIR THE TOOL WHILE CONNECTED TO THE POWERSOURCE. ACCIDENTAL ENGAGEMENT OF THE TOOL CAN CAUSE SERIOUS PERSONALINJURY.

� OIL INJECTION HAZARD EXISTS WITH THIS TOOL. OIL INJECTION IS A CONDITION WHEREHYDRAULIC OIL IS INJECTED UNDER THE SKIN FROM PRESSURE IN THE LINE. ALWAYSWEAR GLOVES AND REPAIR ANY LEAKS IMMEDIATELY. NEVER CARRY A TOOL BY THEHOSES.

� DO NOT USE DAMAGED EQUIPMENT. IMMEDIATELY REPLACE ANY DAMAGED HOSES,FITTINGS, OR OTHER COMPONENTS SHOWING WIRE BRAID, NICKS, CUTS, DAMAGE ORABRASIONS. FAILURE TO DO SO MAY RESULT IN EQUIPMENT DAMAGE AND / OR PER-SONAL INJURY OR DEATH.

� CLEAN UP ANY OIL OR FLUID SPILLS IMMEDIATELY.

5

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

HAVE SUPERVISOR ADD ADDITIONAL PRECAUTIONS RELATING TO THE SPECIFICWORK AREA AND LOCAL SAFETY REGULATIONS BELOW:

**********************

6

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

05100A WELD SHEARSAFETY PRECAUTIONS:1. ALWAYS WEAR SAFETY EQUIPMENT SUCH AS GLOVES, SAFETY GLASSES, EAR

PROTECTION, SAFETY SHOES, AND OTHER REQUIRED SAFETY EQUIPMENT.2. DO NOT WEAR CLOTHING WHICH MAY BECOME ENTANGLED IN THE TOOL.3. KEEP HANDS CLEAR OF WORK AREA AT ALL TIME.4. ALWAYS KEEP WORK AREA FREE OF TOOLS OR ANY OTHER OBJECTS WHICH MAY

IMPAIR SOUND FOOTING.5. CAUTION - OIL INJECTION HAZARD EXISTS WITH THIS TOOL. OIL INJECTION IS A

CONDITION WHERE THE HYDRAULIC OIL IS FORCED UNDER THE SKIN THROUGHPRESSURE IN THE LINE. ALWAYS WEAR GLOVES AND REPAIR LEAKS IMMEDIATELY.

6. BECAUSE OF THE HIGH FIELD WELD TEMPERATURES, IT IS EXTREMELY IMPORTANTTO CHECK FOR WORN HOSES, NICKS, CUTS, AND/OR LEAKS BEFORE EACH SHEAROPERATION. HYDRAULIC OIL HAS A FLASH POINT OF APPROX. 400 DEGREE F. A LEAKDIRECTED INTO THE WELD AREA (1900° F) WILL CAUSE A FIRE AND POSSIBLE SERI-OUS INJURY OR DEATH.

7. DO NOT CLEAN OR INSPECT THE TOOL WHILE IT IS CONNECTED TO THE POWER SOURCE.ACCIDENTAL ENGAGEMENT OF THE TOOL CAN CAUSE SERIOUS INJURY.

8. ALWAYS CHECK WORK AREA FOR ANY TRASH WHICH MY IGNITE FROM SPARKS, WELDSPLATTER OR SLAG.

9. ALWAYS CHECK THE WORK AREA FOR SMOLDERING TIES OR TRASH BEFORE LEAV-ING SITE.

10. NEVER STRIKE HOLD DOWNS WITH ANY OBJECT TO LOOSEN SHEAR FROM THERAIL.

7

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

05100A WELD SHEAR

MODEL NO: 05100AFLOW: 5 GPM (19 LPM)PRESSURE: 2000 PSI (140 BAR)MAX BACK PRESSURE: 250 PSI (17 BAR)

OPERATION:� PLACE THE SHEAR ON THE RAIL PRIOR TO SETTING UP THE WELD TO ADJUST

THE HOLD DOWN LEGS. AFTER HOLD DOWN LEGS ARE ADJUSTED, REMOVESHEAR FROM RAIL TO PREPARE WELD.

1. WITH THE POWER SOURCE IN THE �OFF� POSITION, CONNECT THE HOSES. DONOT DRAG THE SERVICE HOSES BY PULLING WITH THE TOOL. LOOP THE SERVICEHOSE IN THE WORK AREA IN SUCH A WAY TO RELIEVE STRESS ON THE HOSE ANDQUICK DISCONNECT FITTINGS WHILE WORKING. BE AWARE OF HOSE LOCATIONAT ALL TIMES.

2. WHEN THE WELD IS READY TO BE CUT, POSITION TWO PEOPLE, ONE ON EACHSIDE OF THE SHEAR. THEY SHOULD CAREFULLY PLACE THE SHEAR OVER THEWELD AND LOCK IT INTO PLACE WITH THE HOLD DOWN LEGS.

3. TURN THE POWER SOURCE �ON� TO SUPPLY 5 GPM.4. MOVE THE HANDLE TO SIDE THAT IS LABELED SHEAR TO MAKE THE CUT.5. AFTER SHEAR IS COMPLETE, MOVE THE HANDLE THE OPPOSITE DIRECTION (LABELED

RETRACT) TO RETRACT THE SHEAR BLADES.6. TURN POWER SOURCE �OFF�.7. TO REMOVE SHEAR FROM THE RAIL, LOOSEN HOLD DOWNS, POSITION TWO

PEOPLE, ONE ON EACH SIDE OF THE SHEAR, AND CAREFULLY REMOVE FROMTHE RAIL.

8

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

05100A WELD SHEARMAINTENANCE:1. AS THE BLADES WEAR, THE GAP MAY BE CLOSED BY ADJUSTING THE CYLINDER ROD

NUTS ON THE CENTER PLATE OF THE SHEAR. A 1/32� GAP IS RECOMMENDED.2. INSPECT HOSES DAILY. AT THE FIRST SIGN OF ANY ABRASION OR CUT TO THE

COVER, THE HOSES MUST BE CHANGED.3. CHECK ALL FASTENERS DAILY.4. USE ONLY RECOMMENDED HYDRAULIC OILS. NEVER USE ATF OR MOTOR OIL.

SUGGESTED HYDRAULIC OILS:AMOCO RYKON MV CITGO A/W ALL TEMPSUN 2105 MOBIL D.T.E. 15CHEVRON EP-MV TEXACO �RANDO� HD-AZIF YOUR LOCAL DISTRIBUTOR DOES NOT CARRY ANY OF THE ABOVE SUGGESTEDHYDRAULIC OILS USE THE FOLLOWING GUIDELINES:VISCOSITY @ 100° F�����������������100-190SUSVISCOSITY INDEX������������������MIN.150EACH APPLICATION IS DIFFERENT, IF THERE ARE ANY QUESTIONS CONCERNING THERIGHT CHOICE FOR YOUR PARTICULAR APPLICATION CALL MATWELD FOR ASSISTANCE.

5. HAVE TOOL INSPECTED, AT LEAST ANNUALLY, BY A MATWELD OR MATWELD QUALIFIEDSERVICE REPRESENTATIVE TO DETERMINE IF TOOL IS IN NEED OF SAFETY CHANGESOR WORN PART REPLACEMENT.

9

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

05100A WELD SHEARGENERAL NOTES:

10

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

27

5

25 2922

28

21 24 25

30

31

7

28

2524

29

4

31

37

30

29924

28

22

11

3337

15

10

14

12

17

6

16

27

32

34

1

3833

3

13 35

20

37

32

26

35

2 34

19

36

8

24

37

18

4

17

36

14

15

05100AWELD SHEAR

REV.2 01/02

11

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

05100AWELD SHEARPARTS LIST

REV.2 01/02QTY. ITEM NO. PART NO. DESCRIPTION

12345678910111213141516171819202122242526272829303132333435363738

0014500146

00905A00908051010513105103051080511005130051120511305114

05115A05116AA2048

2501-04-06A6308A1001A2062A1021A1083A2000A1465A2190A2191A2194A2197A6105A6079

409-06-063/8X2-1/2-805406-08-06

2601-04-04-042501L-04-045406-06-045502-04-04

1112112211111222221124461444442222241

QUICK DISCONNECT COUPLERQUICK DISCONNECT NIPPLE

VALVE - SPRING CENTERSHEAR CYLINDER

WELD SHEAR FRAMEVALVE BRACKET

FRONT HOLD DOWNCENTER HOLD DOWN

SHEAR CENTER PLATEFITTING GUARDSAFETY SHIELD

SAFETY SHIELD � LOWERHOLD DOWN BRACKET � SHIELDHOSE � CYLINDER EXTENSIONHOSE � CYLINDER RETRACT

5/16-18 NYLOCK NUT3/8NPT X ¼ MJIC 90 EL

5/16-18 X 1 FLAT HEAD BOLT1/4-20 X ¾ GR. 5 ZP.1/4-20 NUT INSERT

5/16-18 X ¾ GR. 5 ZP.1/2-13 X 1-1/2 GR. 5 ZP.

3/4-16 HEX NUT ZP.3/4-16 JAM NUT

¼ SAE FLAT WASHER ZP5/16 SAE FLAT WASHER ZP1/2 SAE FLAT WASHER ZP3/4 SAE FLAT WASHER ZP

½ X 1 SPRING PIN3/16 X 1 SPRING PIN3/8 FP X 3/8 MP 90 EL

3/8 X 2-1/2 NIPPLE1/2X 3/8 HEX BUSHING

1/4 NPT X 1/4 MJIC T1/4NPT X 1/4 MJIC 90 EL

3/8 X 1/4 BUSHING1/4 STREET EL 90

12

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

REVIEW OF HYDRAULIC PRINCIPLES

A. TOOL CIRCUIT

1. HYDRAULIC FORMULAS:

CID X RPM GPM X PSI GPM = 231 HP = 1714 (.85)

1456.9Example: HP required to deliver 10 GPM at 1500 PSI.

10 GPM X 1500 PSI = 15000 = 10.3 HP1456.9 1456.9

(subtract back pressure for tool HP)Estimated HP delivered by pump or used by tool.

PSI GPM 500 1,000 1,500 2,000 2,500 3,000 3 1.03 2.06 3.09 4.12 5.15 6.18 5 1.72 3.43 5.15 6.86 8.58 10.30 10 3.43 6.86 10.3 13.70 17.20 20.60 15 5.15 10.30 15.40 20.60 25.70 30.90

2. BACK PRESSUREBACK PRESSURE MEASURED AT THE TOOL RETURN PORT MUST NOT EXCEED THE MANU-FACTURERS BACK PRESSURE RATING. MOST MANUFACTURERS LIST THE MAXIMUM BACKPRESSURE FOR THEIR HYDRAULIC TOOLS AT 250 PSI. BACK PRESSURE MEASURED ONTHE RETURN SIDE OF THE TOOL IS THE FORCE REQUIRED TO GET THE OIL BACK TO THETANK. IN ALMOST ALL CASES THE LOWER THE BACK PRESSURE THE BETTER THE TOOLPERFORMANCE. FIRST, THE BACK PRESSURE IS SUBTRACTED FROM THE MAXIMUM TOOLPRESSURE TO ARRIVE AT A MAXIMUM TOOL OPERATING PRESSURE. FOR EXAMPLE, TOOLSWITH 2000 PSI OPERATING PRESSURE ARE INSTALLED ON A SYSTEM WITH 250 PSI BACKPRESSURE. THIS LEAVES1750 PSI AS A MAXIMUM TOOL PRESSURE. IMAGINE A SYSTEMWITH 500 PSI BACK PRESSURE. 2000 MINUS 500 PSI BACK PRESSURE LEAVES ONLY 1500PSI FOR THE TOOL. SECOND, TOOLS ARE DESIGNED FOR PRESSURE TO BUILD ON THEPRESSURE SIDE OF THE TOOL. IF TOO MUCH PRESSURE BUILDS ON THE RETURN SIDE,NOT ONLY IS PERFORMANCE EFFECTED, BUT SEALS MAY BLOW. THIS IS WHY IT IS VERYIMPORTANT TO DIRECT THE FLOW INTO THE TOOL CORRECTLY. REVERSING THE HOSESTO TEST MAY RESULT IN BLOWN SEALS, DAMAGE TO THE TOOL, AND PERSONAL INJURY.

13

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

05100A WELD SHEARDECAL LEGEND:

14

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

05100A WELD SHEARGENERAL NOTES:

15

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

LIMITED WARRANTYMATWELD, INC., PADUCAH, KY., WARRANTS TO THE ORIGINAL PURCHASE OF THIS PROD-UCT THAT THE PRODUCT WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIPFOR THE PERIOD OF ONE (1) YEAR AFTER THE DELIVERY OF SUCH PRODUCT TO THE CUS-TOMER. OTHER EQUIPMENT AND PARTS USED, BUT NOT MANUFACTURED BY MATWELDINC. ARE COVERED DIRECTLY BY THE WARRANTY OF THE MANUFACTURER OF THOSE PROD-UCTS. PROOF OF PURCHASE MUST BE DOCUMENTED INCLUDING REFERENCE TO A SE-RIAL NUMBER LOCATED ON EACH TOOL. THE PURCHASER�S ONLY REMEDIES UNDER THISLIMITED WARRANTY SHALL BE LIMITED AT MATWELD�S SOLE OPTION TO THE FOLLOWING:REPAIR, REPLACEMENT OR REFUND OF THE PURCHASE PRICE OF THE DEFECTIVE PROD-UCTS. EACH OF THESE REMEDIES REQUIRES TIMELY NOTIFICATION OF THE DEFECT INTHE PRODUCT AND SUBSTANTIATION THAT THE PRODUCT HAS BEEN PROPERLY STORED,MAINTAINED AND USED. MATWELD�S OBLIGATIONS HEREUNDER EXTEND ONLY TO THEPURCHASER OF THE PRODUCT AND NOT TO ANY THIRD PARTY.AS A CONDITION PRECEDENT TO MATWELD�S OBLIGATION HEREUNDER, THE DEFECTIVE PROD-UCT MUST NOT HAVE BEEN ALTERED OR MODIFIED WITHOUT THE EXPRESS WRITTEN AP-PROVAL OF MATWELD, INC. THE PRODUCT MUST NOT HAVE BEEN SUBJECTED TO DELIBER-ATE DAMAGE, SHIPPING DAMAGE, NEGLECT, TAMPERING BY UNAUTHORIZED PERSONNEL ORDAMAGE BY IMPROPER USE, STORAGE OR MAINTENANCE. SERIAL NUMBERS MUST NOT HAVEBEEN ALTERED, DEFACED OR REMOVED. SUCH ACTION VOIDS LIMITED WARRANTY.

EXCLUSIONS TO LIMITED WARRANTYTHIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRIT-TEN OR ORAL, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIEDWARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.LIMITED WARRANTY DOES NOT COVER NORMAL WEAR AND TEAR ITEMS SUCH AS FIL-TERS, HOSES, COUPLERS, BITS, SOCKETS, AUGERS, AND BATTERIES.

LIMITATION OF LIABILITYEXCEPT AS PROVIDED ABOVE, MATWELD SHALL IN NO EVENT BE LIABLE OR RESPONSIBLEFOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR CONSEQUENTIAL, ARISINGOUT OF THE USE OR MISUSE OR INABILITY TO USE THE PRODUCT, HOWEVER CAUSED ANDON ANY THEORY OF LIABILITY INCLUDING, WITHOUT LIMITATIONS, BREACH OF CONTRACT,TORT, (INCLUDING NEGLIGENCE OR STREET LIABILITY) AND NOT WITHSTANDING ANY FAIL-URE OF ANY REMEDY HEREIN OF ITS ESSENTIAL PURPOSE, EVEN IF MATWELD WAS AWAREOF THIS POSSIBILITY OF SUCH DAMAGE. MATWELD�S LIMITED WARRANTY AS SET FORTHABOVE SHALL NOT BE ENLARGED, DIMINISHED OR AFFECTED BY, AND NO OBLIGATION ORLIABILITY SHALL ARISE OR GO OUT OF THE RENDERING OF TECHNICAL ADVICE OR SER-VICE BY MATWELD OR ITS AGENTS. THE FOREGOING MAY NOT BE CHANGED EXCEPT BYWRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICER OF MATWELD, THE REMEDIESSET FORTH HEREIN ARE EXCLUSIVE.

16

MATWELD, INC. PHONE:(270) 444-0085 FAX:(270) 443-6180Matweld reserves the right to change parts, features, or specifications without notice.

02/01

CUSTOMER INFORMATION:Name _____________________________________________________Company___________________________________________________Serial # of your Matweld tool___________________________________( Upon receiving your Matweld tool, make sure to list serial number above so that a good record is kept fororder information.) MATWELD HYDRAULIC TOOL LIST

All Matweld Hydraulic Tools operate at5 or 10 GPM @ 2000 PSIPOWER UNITS:

07000 � HYDRA POWERED MODULAR SYSTEM02900 � DIESEL 1-10 GPM OR 2-5 GPM

(OPTIONAL CATALYTIC EXHAUST AND/OR MSHA CERTIFIED)00100 � GASOLINE 1-10 GPM OR 2-5 GPM02050 � GASOLINE 1-5 GPM05500 � TWIN POWER DUAL CIRCUIT UNIT 1-10 GPM OR 2-5 GPM & 5000 WATT GENERATOR

TRACK TOOLS:01600A � 1� IMPACT WRENCH04500D � ½� IMPACT DRILL00800A � 16� RAIL SAW03900A � REVERSING RAIL SAW01100 � SPIKE PULLER01300A � TIE TAMPER01400 � SPIKE DRIVER01500 � RAIL DRILL01000 � CHAIN SAW03500 � SELF FEED RAIL DRILL

GRINDERS:04600 & 04650� STRAIGHT STONE CW & TRIGGER VERSION04700 & 04750 � STRAIGHT STONE CCW & TRIGGER VERSION04800 & 04850 � CUPSTONE & TRIGGER VERSION00700 � RAIL SURFACING GUIDE02400 � 10� OR 14� FROG AND SWITCH GRINDER05900 � FROG/PROFILE GRINDER - ON/OFF FLOW CONTROL05950 � FROG/PROFILE GRINDER - SAFETY TRIGGER06000 � PROFILE GRINDER05400 � ANGLE GRINDER

OTHER PRODUCTS:HYDRAULIC MANIFOLDSHYDRAULIC TEST GAUGESHOSE REELSHYDRAULIC HOSESACCESSORIES