04/09/2021 PROJECT MANUAL FOR: New Lowndes High School ...

04/09/2021

PROJECT MANUAL FOR:

New Lowndes High School Furniture, Furnishings and Equipment

OWNER:

Lowndes County School District 1592 Norman Drive

Valdosta, Georgia 31601

ARCHITECT:

McCall Architecture

PHYSICAL ADDRESS: 3308 Country Club Rd.

Valdosta, Georgia 31605

MAILING ADDRESS: P.O. Box 5146

Valdosta, Ga. 31603

P: 229.242.2551 F: 229.244.8358

www.mccallinc.com

New Lowndes High School Furniture, Furnishings and Equipment 04/09/2021

TABLE OF CONTENTS-1

TABLE OF CONTENTS COVER 1 TABLE OF CONTENTS 1 DIVISION 0 – PROCUREMENT AND CONTRACTING REQUIREMENTS Section A 1 - 2 INVITATION TO BID Section B 1 - 6 PROPOSAL FORM Section C 1 - 8 INSTRUCTIONS TO BIDDERS Section D 1 -18 AIA DOCUMENT A151 – STANDARD FORM OF AGREEMENT BETWEEN OWNER AND VENDOR 002600 1-3 EXISTING CONDITION INFORMATION DIVISION 1 - GENERAL REQUIREMENTS 013300 1-8 SUBMITTAL PROCEDURES

017419 1-2 CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL DIVISIONS 2 – 11 NOT USED DIVISION 12 - FURNISHINGS

120100 1-120 FURNITURE, FURNISHINGS AND EQUIPMENT DIVISIONS 13 – 33 NOT USED END

New Lowndes High School Furniture, Furnishings and Equipment 04-09-21

INVITIATION TO BID A-1

A - INVITATION TO BID Sealed Proposals will be received by the Lowndes County School District in the Board Room of the Lowndes County Board of Education offices, 1592 Norman Drive, Valdosta, Georgia 31601, on May 11, 2021 until 2:00 p.m., prevailing time, for the project entitled “New Lowndes High School Furniture, Furnishings and Equipment”. At the time and place noted above, the proposals for the above referenced project will be publicly opened and read. No extensions of the bidding period will be made. Proposals submitted by mail or courier should be addressed to the Lowndes County Board of Education, 1592 Norman Drive, Valdosta, Georgia 31601, and should be plainly marked as indicated in the Instructions to Bidders. Bid Documents and Addenda are available in electronic format and can be viewed and downloaded from the Georgia Procurement Registry at https://ssl.doas.state.ga.us/gpr. Bid Documents and Addenda can also be viewed and downloaded from the Lowndes County Schools website by accessing the “Purchasing” link at www.lowndes.k12.ga.us. Contact Jeff Hill, Facilities Coordinator, at [email protected], or 229-412-7316 if you experience technical difficulties with the Lowndes County Schools website. ALL bidders are responsible to check for any issued Addenda to the Bid Documents and to acknowledge all Addenda in the Proposal Form, Section B of the Project Manual. All questions shall be submitted to John M. ”Mac” McCall, Architect at [email protected]. ANY UNSOLICITED CONTACT OR COMMUNICATION REGARDING THIS PROJECT WITH ANY LOWNDES COUNTY SCHOOL DISTRICT OR LOWNDES COUNTY BOARD OF EDUCATION OFFICIALS, PERSONNEL OR BOARD MEMBERS BY ANYONE FROM WITHIN OR ON BEHALF OF A PROPOSING FIRM IS STRICTLY PROHIBITED AND WILL BE GROUNDS FOR DISQUALIFICATION. THIS APPLIES FROM THE DATE OF ISSUANCE OF THIS INVITATION TO BID UNTIL AFTER A CONTRACT HAS BEEN AWARDED TO THE SUCCESSFUL VENDOR/CONTRACTOR. Contract, if awarded, will be on a lump sum basis. No bid may be withdrawn for a period of days indicated in the Proposal Form, after time has been called on the date of opening of bids. Bids must be accompanied by a Bid Bond in an amount not less than 5% of the Base Bid. The successful bidder will be required to furnish both a Performance Bond and Payment Bond, each in an amount equal to 100% of the contract sum. Use current AIA Bond forms. All sureties must be authorized to transact business in the State of Georgia.

https://ssl.doas.state.ga.us/gpr/

http://www.lowndes.k12.ga.us/

mailto:[email protected]



INVITIATION TO BID A-2

The Owner reserves the right to reject any or all bids and to waive technicalities and informalities. BY: _________________________________

Jeff Hill, Facilities Coordinator Lowndes County Schools


SECTION B – PROPOSAL FORM B-1

SECTION B - PROPOSAL FORM Date_________________________ Lowndes County School District c/o Lowndes County Board of Education 1592 Norman Drive Valdosta, GA 31601 RE: New Lowndes High School

Furniture, Furnishings, and Equipment Gentlemen: 1. Having carefully examined the Bid Documents entitled “New Lowndes High School

Furniture, Furnishings and Equipment, dated April 9, 2021, and Addendum No.(s)____________________ as well as the premises and conditions affecting the Work, the undersigned proposes to furnish all services, labor, equipment, products and materials called for by them for the entire Work, in accordance with said documents, for the sum of _______________________________________________________

($___________________________________________________) DOLLARS which sum is hereinafter called the Base Bid.

2. Not used 3. For and in consideration of the sum of $10.00, the receipt of which is hereby

acknowledged, the undersigned assumes the obligation to save the Owner and the Architect harmless and to indemnify the Owner and Architect for every expense, liability or payment arising out of or through injury (including death) to any person or persons or damage to property of any persons of any place in which work is located arising out of or suffered through any act or omission of the Vendor, any of the Vendor’s subcontractors or suppliers, or anyone either:

(1) directly or indirectly employed, by or (2) under the supervision or any of them in the prosecution of the work included in this contract.

4. For and in consideration of the sum of $20.00, the receipt of which is hereby

acknowledged, the undersigned agrees that this proposal may not be revoked or withdrawn after the time set for the opening of bids, but shall remain open for acceptance for a period of thirty-five (35) days following such time.

5. In case he be notified in writing by mail, telegraph, or delivery of the acceptance of this

proposal within thirty-five (35) days after the time set for the opening of bids, the undersigned agrees to execute within ten (10) days a contract, AIA Document A151 –



2019 Agreement Between Owner and Vendor for Furniture, Furnishings and Equipment, as Modified, for the Work for the above stated compensation and at the same time to furnish and deliver to the Owner a separate Performance and Payment Bond, each in an amount equal to 100% of the contract sum.

6. The undersigned agrees to commence Work with an adequate force and equipment

upon written order of the Owner. Initial Work will include all activities required to acquire furniture, furnishings and equipment (FF&E) including, but not limited to submittals, acquiring approvals, ordering, storing if necessary, and any other activities required to have FF&E ready for installation/placement upon notification to commence with install/placement. In accordance with the current construction schedule, on, or around October 18, 2021, the construction of the new high school facility will be declared substantially complete and the successful Bidder will receive a second notification that installation and placement procedures for the FF&E package may commence. The entire FF&E package shall be installed/placed and the Project shall be complete and turned over to the Owner not later than 6 weeks after the Vendor is notified to proceed with installation/placement.

For each calendar day beyond the established completion date that the work remains incomplete (completeness will be determined by the Architect in accordance with the terms of the contract) the Vendor shall pay the Owner the sum of $250.00 per day as actual damages to the Owner for the Owner being unable to obtain possession and use of the premises at the site. The Vendor hereby acknowledges that time is of the essence and in this contract is a material consideration thereof.

7. Enclosed herewith is a Bid Bond in the amount of 5% of the Base Bid ____________________________________________DOLLARS ($___________). The undersigned agrees that the above stated amount is the proper measure of liquidated damages which the Owner will sustain by the failure of the undersigned to execute the contract and/or to furnish the Performance and Payment Bonds from the undersigned or any of his qualifying subcontractors. The obligation of the Bid Bond will remain in full force and effect and the money payable hereon shall be paid into the funds of the Owner as liquidated damages for such failure; otherwise, obligation of the bond will be null and void.

8. If this bid is accepted within thirty-five (35) days after the date set for the opening of bids

and the undersigned fails to execute the contract within ten (10) days after written notice of such acceptance or if he fails to furnish both Performance and Payment Bonds, the obligation of the Bid Bond will remain in full force and effect and the money payable thereon shall be paid into the funds of the Owner as liquidated damages for such failure; otherwise, obligation of the bond will be null and void.

9. The bidder submits the following statement of bidder's qualifications (Appendix A) for

consideration of the Owner.



10. By signing this Bid Form, the bidder acknowledges that the information which is requested under the statement of qualifications is for the Owner’s use for the purpose of evaluating the prior performance of the contractor in order to assist the Owner in making a decision for the award of the work represented in this bid package; and that the Owner is authorized by the bidder to gather information about the bidder and to use that information, at the Owner’s discretion, in evaluating the this proposal and making a decision as to the award of the work. Further, the bidder herewith acknowledges that the Owner reserves the right to reject any or all bids and to waive technicalities, and informalities. Further, the contractor acknowledges that the owner reserves the right to award the work at the owner’s discretion, as the owner determines may be in the owner’s best interest.

11. By submitting this Bid, the Bidder represents the following:

a. the Bidder has read and understands the Bidding Documents; b. the Bidder understands how the Bidding Documents relate to other

portions of the Project, if any, being bid concurrently or presently under construction;

c. the Bid complies with the Bidding Documents; d. the Bid is based upon the materials, equipment and systems required by

the Bidding Documents without exception, such that all furniture, furnishings and equipment included in this bid are either Basis-of-Design, as specified, or comparable substitute furniture, furnishings and equipment as approved and issued by addendum(a);

e. the Bidder has visited the site, become familiar with local conditions under which the Work is to be performed, and has correlated the Bidder’s observations with the requirements of the Proposed Contract Documents;

f. the Bidder has read and understands the provisions for liquidated damages set forth in the form of Agreement between the Owner and Vendor.

12. The bidder is advised that in the event of a tie bid in which two (2) or more bidders

offer, at identical prices, products that meet all specifications, terms, and conditions of the bidding documents, State of Georgia statutes provide three (3) preferences which shall be used to resolve tie bids whenever applicable: (1) preference for products manufactured or produced within the State of Georgia; (2) preference for products sold by local bidders/offerors within the State; (3) preference for products manufactured or sold by small business. If these statutes are insufficient to resolve the tie, the following will be considered in the order listed:

(1) Past performance of bidders (2) Earliest delivery date (3) Closest proximity to delivery site (4) Flip a coin


APPENDIX A SECTION B – PROPOSAL FORM B-4

APPENDIX A

STATEMENT OF BIDDER'S QUALIFICATIONS

To accompany bids submitted for ___________________________________________________

__________________________ at __________________________________________________

Name of Bidder _________________________________________________________________

Business Address ________________________________________________________________

When Organized ________________________________________________________________

Where Incorporated ______________________________________________________________

How many years have you been engaged in this field? __________________________________

Financial Statement Available? _____________________________________________________

Credit Available for this Contract $ __________________________________________________

Provide the following information on Surety Company that will provide Performance and Payment Bonds: _________________________________________________________________________

Name:_________________________________________________________________________

Address: _______________________________________________________________________

State of Georgia Bond Agent Name: ________________________________________________

Address: _______________________________________________________________________

** Provide the following as a part of the Bid Package: 1. A statement on Surety Company letterhead, signed by the State of Georgia Bond Agent of

the Surety Company listing State of Georgia license, A.M. Best "A-6" rating (or better), and US Treasury Circular 570 listing including underwriting limitation, and confirming surety company’s willingness and ability to issue the required performance and payment bonds for this project and contractor.

2. Georgia Security and Immigration Compliance Act Affidavit (E-Verify) – Provide completed and signed Contractor Affidavit.

3. Provide a complete schedule of ALL proposed furniture, furnishings, and equipment, listing manufacturer, series, model No., color and quantity.

4. List of all lawsuits, arbitration, and mediation in which the bidder has been involved in the last ten years:



Name of Project

Type of law suit/ arbitration/mediation

Project Owner's name and telephone number

5. List a minimum of three installations of comparable size, scope, and complexity, completed within the last five years along with references:

1) Name of Project: ___________________________________________________

Contact Person: ____________________________________________________

Telephone Number: _________________________________________________

E-mail Address:_____________________________________________________

Date of Completion: ________________________________________________

2) Name of Project: ___________________________________________________

Contact Person: ____________________________________________________


E-mail Address:_____________________________________________________


3) Name of Project: ___________________________________________________

Contact Person: ____________________________________________________


E-mail Address:_____________________________________________________




Have you ever refused to sign a contract at your original bid? ____________________________ Have you ever been declared in default on a contract? _________________________________ Remarks: _______________________________________________________________________

______________________________________________________________________________

Respectfully submitted,

Name:_____________________________________

Address: ___________________________________

__________________________________________

By: ________________________________________

Title: ______________________________________

The full names and addressed of persons and firms interested in the foregoing bids as principals are as follows: ______________________________________________________________________________

______________________________________________________________________________

______________________________________________________________________________

The legal name of the bidder is:

__________________________________________________________________

The above statements must be subscribed and sworn to before a Notary Public

Date: ______________________________________

Firm Name: ________________________________

By: ________________________________________

Title: ______________________________________

Corporate Seal

__________________________________________

(Notary Public)

New Lowndes High School Furniture, Furnishings & Equipment 04-09-2021

SECTION C – INSTRUCTIONS TO BIDDERS C-1

C INSTRUCTIONS TO BIDDERS C-01 BASIS OF CONTRACT

See Invitation to Bid and Proposal Form. C-02 BID SECURITY

See Invitation to Bid and Proposal Form. C-03 INTERPRETATIONS

No oral interpretation will be made to bidders as to the meaning of the bidding documents. Requests for clarification or interpretation of bidding documents must be made in writing to the Architect not later than ten (10) days prior to the date set for receipt of the bids, and failure on the part of the successful bidder to do so shall not relieve him as vendor/contractor of the obligation to execute such work in accordance with a later interpretation by the Architect. All interpretations made to bidders will be issued in the form of addenda to the Bidding Documents. These addenda will be available as stated in the Invitation to Bid.

C-04 PROPOSALS

a. Proposals will be opened and read as stated in the Invitation to Bid.

b. All bids must be submitted in duplicate, on the same form as the specimen shown in Section B and must be signed. All blanks on the proposal form must be filled in. Upon request, three loose copies will be furnished bidders for their use. Numbers shall be written in English words and in Arabic numerals, and the completed form shall be without interlineation, alteration or erasure. Failure to submit a proposal in the form requested or the inclusion of any condition, alternate limitation or provision not called for will render the bid irregular and shall be considered sufficient cause for rejection of a bid. Failure to complete entries in all blanks in the proposal form shall be considered sufficient cause for rejection of a proposal.

c. Proposals are to be addressed to the Owner at the address shown in the Advertisement for Bids and must be enclosed in an opaque, sealed envelope marked "Proposal for New Lowndes High School - Furniture, Furnishings and Equipment". Bids are to reach the address designated in the Advertisement for Bids not later than the hour and date named in the Invitation to Bid. After that time, no bids will be accepted.

d. Proposals together with the full bid security accompanying same may be withdrawn by bidders prior to the time set for official opening. After the time has been called, no bid may be withdrawn for a period of the number of days indicated in the Proposal Form, after the time and date of opening. Negligence or error on the part of any bidder in preparing his bid confers no right of withdrawal or modification of his bid after time has been called.

e. Bidder shall bear all costs associated with preparation of Bid.

C-05 EXISTING CONDITIONS

In undertaking the work under this contract, the Bidder is assumed to have visited the premises

and to have taken into consideration all conditions which might affect his work. No consideration will be given any claim based on lack of knowledge of existing conditions except where existing conditions are such as cannot be readily ascertained.



C-06 ADDENDA – CLARIFICATIONS AND/OR CHANGES The bidder acknowledges that the bidder has carefully studied the contract documents and has

requested and received by addendum(a) clarifications and/or changes in the contract documents in connection with ambiguities, inconsistencies, coordination, errors and omissions and has included the cost of ambiguities, inconsistencies, coordination, errors and omissions (except covered existing conditions) in the contractor's proposal for the work.

C-07 SAFETY AND SOUNDNESS

The bidder acknowledges that he possesses and maintains all the knowledge, skill and

experience necessary to perform the work of this project and will provide all of the labor, plant and material necessary to perform the work of this project and that the cost of all of the knowledge, skill, experience, labor, plant and material necessary to produce the work of this project is included in the bidder’s proposal, including, but not limited to, the specific requirements of the work.

C-08 MEANS, METHODS, TECHNIQUES, SEQUENCES, TIMING AND COORDINATION

The bidder acknowledges that he is responsible for and will provide all necessary means,

methods, techniques, sequences, timing, and coordination to diligently and orderly perform the work in accordance with the contract documents and that the cost of the bidder providing all necessary means, methods, techniques, sequences, timing and coordination to diligently and orderly perform the work in accordance with the contract documents is included in the bidder’s proposal.

C-09 DUE DILIGENCE, DISCOVERY

The bidder acknowledges that he has exercised due diligence in connection with the discovery

of ambiguities, inconsistencies, coordination, errors and omissions in connection with the contract documents of this work and has included the cost of ambiguities, inconsistencies, coordination, errors and omissions (except covered existing conditions) in the contractor’s proposal for the work. C-10 Whenever the terms “Contractor” and “Vendor” are used throughout the Project Manual, these terms are interchangeable and shall refer to the same entity. C-11 CONTRACT FORM AND BONDS

The bidder’s attention is directed to Section B, Proposal Form. C-12 AWARD

The Owner reserves the right to reject any or all bids and to waive technicalities and informalities.

In the event of a tie bid in which two (2) or more bidders offer, at identical prices, products that

meet all specifications, terms, and conditions of the bidding documents, State of Georgia statutes provide three (3) preferences which shall be used to resolve tie bids whenever applicable: (1) preference for products manufactured or produced within the State of Georgia; (2) preference for products sold by local bidders/offerors within the State; (3) preference for products manufactured or sold by small business. If these statutes are insufficient to resolve the tie, the following will be considered in the order listed: (1) Past performance of bidders



(2) Earliest delivery date (3) Closest proximity to delivery site (4) Flip a coin C-13 SURETY AND INSURANCE COMPANIES

The contract documents require that the surety and insurance companies be acceptable to the Owner. See Project Manual Section D, paragraph entitled "Contractor's Minimum Liability Insurance, Owner's Liability Insurance, Fire Insurance with Extended Coverage" for requirements for insurance company and paragraph entitled "Guaranty Bonds" for requirements for bonding company. To avoid inconvenience, any bidder or subcontractor should get in touch with the Owner to determine whether the surety or insurance companies expected to be used on the work are acceptable to the Owner. C-14 CONTRACTOR/VENDOR For the purposes of this Project and the Contract Documents, whenever the terms “Vendor” and “Contractor” are used, they are used interchangeably and refer to the entity with which the Owner will contract to perform this Project. C-15 OWNER

Wherever the term "Owner" is used in these specifications, it refers to Lowndes County School District. C-16 ARCHITECT

Wherever the term "Architect" is used in these specifications, it refers to McCall & Associates, Inc., 3308 Country Club Road, Valdosta, Georgia, 31605. C-17 MATERIALS

All materials used in the work shall be new unless specifically specified otherwise. C-18 MEASUREMENTS AND DIMENSIONS

Before ordering materials or doing work which is dependent for proper size of installation upon coordination with building conditions, the contractor shall verify all dimensions by taking measurements at the building site. Any discrepancies between contract documents and conditions existing at the site shall be referred to the Architect for adjustment before any work affected thereby is begun. C-19 COOPERATION

The contractor and all subcontractors shall cooperate with one another and with other contractors doing related work, and shall coordinate their work with the work of other trades and other contractors so as to facilitate the general progress of the work. Each trade shall afford all other trades and all other contractors every reasonable opportunity for the installation of their work and for the storage of their materials. C-20 CODES



All materials, construction and activities required of the Work of this Contract shall conform to the requirements of all building codes and sanitary laws in effect in the City and/or County in which the Work is performed. The Contractor shall obtain and pay for all necessary permits, inspections, tests and insurance required by law. C-21 SUBMISSION OF INSURANCE POLICIES, ETC.

In addition to the execution of the contract and the Bond requirements as set forth in these specifications, the successful contractor shall also submit to the Architect the following according to the schedule shown below:

a. At the same time that he submits all Performance and Payment Bonds to the Architect, the contractor shall also submit to the Architect all insurance certificates and policies as called for by the general conditions covering all work of the contractor's forces.

b. Within ten (10) days after Notice to Proceed with his proposal, the contractor shall submit to the Architect for his approval a separate ORIGINAL COST BREAKDOWN for the work.

c. Within 10 days of the Notice to Proceed the Contractor shall submit to the Architect a progress schedule for the entire project. Prepare schedule shall clearly show when each phase of the work will occur. C-22 SPECIAL NOTE

a. All samples, insurance policies, bonds, payment requisitions, etc., shall be submitted to McCall & Associates, Inc., 3308 Country Club Road, P. O. Box 5146, Valdosta, Georgia 31603.

b. All inquiries to the Architect during bidding and construction shall be directed to John M. McCall at [email protected]. C-23 SAFETY AND HEALTH REQUIREMENTS

The Contractor, by signing the contract, acknowledges that he is aware of and familiar with the contents and requirements of the following acts and executive orders:

1. High Voltage Act - Georgia Law 1960. PP. 181-183. 2. Underground Gas Pipe Law - Georgia Law 1969, PP. 50-57. 3. Williams Steiger Occupation Safety and Health Act of 1970. 4. The non-discrimination clause contained in Section 202 Executive Order 11246 as amended by Executive Order 11375 relative to Equal Employment Opportunity for all persons without regard to race, color, religion, sex, or national origin and the implementing rules and regulations described by the Secretary of Labor are incorporated.

C-24 NOT USED C-25 AFFIDAVITS




Before acceptance of work, the contractor will be required to furnish Statutory Affidavit in

duplicate in exact form as shown hereinbelow. After award and before Notice to Proceed is issued, submit Georgia Security and Immigration

Compliance Affidavit and Background Check Affidavit in the exact form as shown herein.



STATUTORY AFFIDAVIT COUNTY OF ______________________________ STATE OF _____________________ FROM: ___________________________________

Contractor TO: _____________________________________ Owner Re: Contract entered into the _____ day of ______________, 20__, between the above-mentioned parties for the construction of _____________________________________________(Project) located at ______________________________________________________________ KNOW ALL MEN BY THESE PRESENTS: 1. The undersigned hereby certifies that all work required under the above contract has been performed in accordance with the terms thereof, that all materialmen, subcontractors, mechanics, and laborers have been paid and satisfied in full, and that there are no outstanding claims of any character [including disputed claims or any claims to which the Contractor has or will assert any defense] arising out of the performance of the contract which have not been paid and satisfied in full except as listed hereinbelow: [Instructions-ENTER THE WORD "NONE" OR LIST THE NAMES OF CLAIMANTS AND THE AMOUNT CLAIMED BY EACH] 2. The undersigned further certifies that to the best of his knowledge and belief there are no unsatisfied claims for damages resulting from injury or death to any employees, subcontractors, or the public at large arising out of the performance of the contract, or any suits or claims for any other damage of any kind, nature, or description which might constitute a lien upon the property of the Owner. 3. The undersigned makes this affidavit for the purpose of receiving final payment in full settlement of all claims against the Owner arising under or by virtue of the contract, and acceptance of such payment is acknowledged as a release of the Owner from any and all claims arising under or by virtue of the contract. IN WITNESS WHEREOF, The undersigned has signed and sealed this instrument this ______ day of ____________________________, 20_____. ___________________________________(Contractor) Signature ___________________________________________ Title ___________________________________________ Corporate Seal Firm COUNTY OF _______________________________ STATE OF ________________________________ Personally before me, the undersigned authority, appeared ____________________________________, who (NAME OF PERSON SIGNING AFFIDAVIT) is known to me to be an official of the firm of ________________________________ who, after being duly (NAME OF CONTRACTOR) sworn, stated on his oath that he had read the above statement and that the same is true and correct. _________________________________________Notary Public, My commission expires _________________ This __________ day of _______________________________, 20___



GEORGIA SECURITY AND IMMIGRATION COMPLIANCE ACT AFFIDAVIT

Project No. and Name: ______________________________________________

______________________________________________

Construction Professional: ______________________________________________

STATE OF GEORGIA; COUNTY OF _______________________________:

CONTRACTOR AFFIDAVIT

By executing this affidavit, the undersigned Contractor verifies its compliance with O.C.G.A. §13-10-91, stating affirmatively that the individual, firm, or corporation which is contracting with the ______________ (Owner) has registered with and is participating in a federal work authorization program*, in accordance with the applicability provisions and deadlines established in O.C.G.A. 13-10-91.

The undersigned further agrees that, should it employ or contract with any subcontractor(s) in connection with the physical performance of services pursuant to this contract with the ______________ (Owner), Contractor will secure from such subcontractor(s) similar verification of compliance with O.C.G.A. § 13-10-91 on the Subcontractor Affidavit provided in Rule 300-10-01-.08 or a substantially similar form. Contractor further agrees to maintain records of such compliance and provide a copy of each such verification to the ____________________ (Owner) at the time the subcontractor(s) is retained to perform such service. _______________________________________ EEV / E-VerifyTM User Identification Number _______________________________________ ___________________________ BY: Authorized Officer or Agent Date (Contractor Name) _______________________________________ Title of Authorized Officer or Agent of Contractor _______________________________________ Printed Name of Authorized Officer or Agent SUBSCRIBED AND SWORN BEFORE ME ON THIS THE _____ DAY OF ______________________, 200_ ________________________________________ [NOTARY SEAL] Notary Public My Commission Expires: *any of the electronic verification of work authorization programs operated by the United States Department of Homeland Security or any equivalent federal work authorization program operated by the United States Department of Homeland Security to verify information of newly hired employees, pursuant to the Immigration Reform and Control Act of 1986 (IRCA), P.L. 99-603



BACKGROUND CHECK AFFIDAVIT Project No. and Name: ______________________________________________

______________________________________________

Construction Professional: ______________________________________________

STATE OF GEORGIA; COUNTY OF _______________________________:

CONTRACTOR AFFIDAVIT

By executing this affidavit, the undersigned Contractor certifies: 1. ALL personnel entering or occupying the project job site have passed a background check

performed by the Sheriff’s Department in the County of the project job site. 2. A file containing that background check of each person permitted access to the project job

site will be maintained by the Contractor and available for inspection by the Owner. 3. Personnel with the following offenses shall be considered as having failed the background

check and are therefore not permitted access to the project job site: a. Documented sex offenders b. Any capital offense c. Conviction of violent acts involving a minor

The undersigned further agrees that, should it employ or contract with any subcontractor(s),

materialmen, suppliers, laborers, etc. in connection with the physical performance of services pursuant to this contract or who would otherwise require access to the project job site, Contractor will secure the required background check on each person and verify compliance with the requirements herein prior to such person being allowed access to the project job site. _______________________________________ ___________________________ BY: Authorized Officer or Agent Date (Contractor Name) _______________________________________ Title of Authorized Officer or Agent of Contractor _______________________________________ Printed Name of Authorized Officer or Agent SUBSCRIBED AND SWORN BEFORE ME ON THIS THE _____ DAY OF ______________________, 200_ ________________________________________ [NOTARY SEAL] Notary Public My Commission Expires:

Section D AIA Document A151-2019, Standard Form of Agreement between Owner and Vendor for Furniture, Furnishings, and Equipment (FF&E)

This document combines A151-2007 (Agreement) and A2510-2007 (General Conditions) For the purposes of this Project, this document serves as the General Conditions and the Agreement and is used in conjunction with the remainder of the Project Manual to identify the requirements of this Project

New Lowndes High School 04-09-21 Furniture Package

PROCUREMENT SUBSTITUTION PROCEDURES 002600 - 1

DOCUMENT 002600 - PROCUREMENT SUBSTITUTION PROCEDURES

1.1 DEFINITIONS

A. Procurement Substitution Requests: Requests for changes in products, materials, and equipment from those indicated in the Bid and Contract Documents, submitted prior to receipt of bids.

B. Requests for changes in products, materials and equipment received after award of Project will NOT be considered.

1.2 PROCUREMENT SUBSTITUTIONS

A. Procurement Substitutions, General: By submitting a bid, the Bidder represents that its bid is based on either Basis-of-Design FF&E described in the Bidding Documents, or approved comparable FF&E issued by Addendum.

B. The burden of proving acceptability of a proposed product for use in place of a Basis-of-Design product or products designated in the Bidding Documents rests solely on the party submitting request for approval.

C. There will be no fabric substitutions.

D. A proposed comparable product must meet or exceed all express requirements of the Basis-of-Design Product including elements such as style, durability, colors, fabric, textures, materials, dimensions, warranty requirements, weight restrictions/limits, etc. A product will be approved as “comparable” only if it is determined by the Architect to be equal or better than the Basis-of-Design Product. A product proposed as “equal” or “better” shall only be considered as such if extremely similar in design, detailing, and other key elements identified by these specifications.

1.3 SUBMITTALS

A. Procurement Substitution Request must be made in writing to the Architect and must be in compliance with the following requirements:

1. Requests for substitution of a proposed comparable product or products to those specified will be considered only if received no later than 10 days prior to date set for bid opening.

2. Proposed substitutions will only be considered from manufacturers listed on Basis of Design spec sheets for corresponding Basis-of-Design product.

3. Submittal Format: Submit three copies of each written Procurement Substitution Request following the format listed below.

a. Clearly identify the product to be replaced in each request. Include related Specifications Sections.



b. Provide complete product specifications and other pertinent documentation on both the product specified and the proposed substitute, including the following information for the Architect’s use in comparing products:

1) Complete product/technical data, specifications and pictures in support of the request for substitution.

2) Copies of current test data/reports of product characteristics from reputable independent third-party testing laboratories

3) Verified experience records demonstrating the reputation of the proposed product with previous users

4) Confirmation from manufacturer that they can meet the schedule indicated in the Bidding Documents.

5) Evidence of reputation of the manufacturer for efficiency in servicing its products. Evidence shall include verified experience records which demonstrate the reputation of the manufacturer to provide prompt and experienced service technicians.

6) Point-by-point, detailed comparison of the specified product and proposed comparable product listing the ways in which the proposed comparable product, material or equipment submitted for consideration compares to the product, material or equipment specified in the Bidding Documents. Point-by-point comparison should include at least the following features and should specifically point out the similarities and differences:

a) Style b) Durability c) Colors d) Textures e) Materials f) Dimensions g) Warranty requirements h) Weight restrictions/limits i) Other

7) Provide certification by manufacturer that the proposed substitute product is equal to or superior to the Basis-of Design product listed in the Bidding Documents, and that its in-place performance will be equal to or superior to the product or equipment specified for the application indicated.

8) Bidder, in submitting the Procurement Substitution Request, waives the right to additional payment or an extension of Contract Time because of the failure of the substitute product to perform as represented in the Procurement Substitution Request.

9) It is imperative that these instructions be followed. Submittal of products of inferior quality and/or different style, durability, colors, textures, materials, warranty requirements, weight restrictions/limits, etc., will not be considered. If the



instructions herein are not followed accurately and in detail, the request will not be considered.

B. Architect's Action:

1. Architect may request additional information or documentation necessary for evaluation of the Procurement Substitution Request.

2. Architect will notify all bidders of acceptance of proposed substitutions by means of an Addendum to the Bidding Documents.

C. If a Bidder submits a bid which includes an approved comparable product, that bidder’s bid package must also include all above-required submittal data for the approved comparable product.

D. Architect's approval of a substitute during bidding does not relieve Contractor of the responsibility to submit all required submittals and to comply with all other requirements of the Contract Documents.

E. If a Bidder submits a bid which includes a product that is neither a Basis-of-Design product as specified nor an approved comparable product, his bid will be considered non-responsive.

END OF DOCUMENT 002600


SUBMITTAL PROCEDURES 013300 - 1

SECTION 013300 - SUBMITTAL PROCEDURES

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Project Manual and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section Includes:

1. Submittal schedule requirements. 2. Administrative and procedural requirements for submittals.

1.3 DEFINITIONS

A. Action Submittals: Written and graphic information and physical samples that require Architect's responsive action. Action submittals are those submittals indicated in individual Specification Sections as "action submittals."

B. Informational Submittals: Written and graphic information and physical samples that do not require Architect's responsive action. Submittals may be rejected for not complying with requirements. Informational submittals are those submittals indicated in individual Specification Sections as "informational submittals."

1.4 SUBMITTAL FORMATS

A. Submittal Information: Include the following information in each submittal:

1. Project name. 2. Date. 3. Name of Architect. 4. Name of Contractor. 5. Name of firm or entity that prepared submittal. 6. Names of subcontractor, manufacturer, and supplier. 7. Unique submittal number, including revision identifier. Include Specification Section

number with sequential alphanumeric identifier; and alphanumeric suffix for resubmittals.

8. Category and type of submittal. 9. Submittal purpose and description.



10. Number and title of Specification Section, with paragraph number and generic name for each of multiple items.

11. Drawing number and detail references, as appropriate. 12. Indication of full or partial submittal. 13. Location(s) where product is to be installed, as appropriate. 14. Other necessary identification. 15. Remarks. 16. Signature of transmitter.

B. Options: Identify options requiring selection by Architect.

C. Deviations and Additional Information: On each submittal, clearly indicate deviations from requirements in the Contract Documents, including minor variations and limitations; include relevant additional information and revisions, other than those requested by Architect on previous submittals. Indicate by highlighting on each submittal or noting on attached separate sheet.

D. Paper Submittals:

1. Only product Samples are allowed as paper/physical submittals. Include a PDF copy of all paper submittals with the Digital Submittal. Color/texture samples will not be reviewed for approval unless a physical sample is provided.

E. Digital Submittals: 1. All submittals will be submitted digitally using the Architects Web Based Project

Software.

1.5 SUBMITTAL PROCEDURES

A. Prepare and submit submittals required by individual Specification Sections. Types of submittals are indicated in individual Specification Sections.

1. Web-Based Project Software: Prepare submittals in PDF form, and upload to web-based Project software website. Enter required data in web-based software site to fully identify submittal.

2. All submittals will be digital except samples. All samples shall be delivered to the Architect’s office.

B. Coordination: Coordinate preparation and processing of submittals with performance of construction activities.

1. Coordinate each submittal with fabrication, purchasing, testing, delivery, other submittals, and related activities that require sequential activity.

2. Submit all submittal items required for each Specification Section concurrently unless partial submittals for portions of the Work are indicated on approved submittal schedule.

3. Submit action submittals and informational submittals required by the same Specification Section as separate packages under separate transmittals.



4. Coordinate transmittal of submittals for related parts of the Work specified in different Sections so processing will not be delayed because of need to review submittals concurrently for coordination.

a. Architect reserves the right to withhold action on a submittal requiring coordination with other submittals until related submittals are received.

C. Processing Time: Allow time for submittal review, including time for resubmittals, as follows. Time for review shall commence on Architect's receipt of submittal. No extension of the Contract Time will be authorized because of failure to transmit submittals enough in advance of the Work to permit processing, including resubmittals.

1. Initial Review: Allow 15 days for initial review of each submittal. Allow additional time if coordination with subsequent submittals is required. Architect will advise Contractor when a submittal being processed must be delayed for coordination.

2. Intermediate Review: If intermediate submittal is necessary, process it in same manner as initial submittal.

3. Resubmittal Review: Allow 15 days for review of each resubmittal. 4. Sequential Review: Where sequential review of submittals by Architect's consultants,

Owner, or other parties is indicated, allow 21 days for initial review of each submittal.

D. Resubmittals: Make resubmittals in same form as initial submittal.

1. Note date and content of previous submittal. 2. Note date and content of revision in label or title block and clearly indicate extent of

revision. 3. Resubmit submittals until they are marked with approval notation from Architect's

action stamp.

E. Distribution: Furnish copies of final submittals to manufacturers, subcontractors, suppliers, fabricators, installers, authorities having jurisdiction, and others as necessary for performance of construction activities. Show distribution on transmittal forms.

F. Use for Construction: Retain complete copies of submittals on Project site. Use only final action submittals that are marked with approval notation from Architect's action stamp.

1.6 SUBMITTAL REQUIREMENTS

A. Product Data: Collect information into a single submittal for each element of construction and type of product or equipment.

1. If information must be specially prepared for submittal because standard published data are unsuitable for use, submit as Shop Drawings, not as Product Data.

2. Mark each copy of each submittal to show which products and options are applicable. 3. Include the following information, as applicable:

a. Manufacturer's catalog cuts. b. Manufacturer's product specifications.



c. Standard color swatches/samples for all finishes. **Color charts will not be accepted.**

d. Statement of compliance with specified referenced standards. e. Testing by recognized testing agency. f. Application of testing agency labels and seals. g. Notation of coordination requirements. h. Availability and delivery time information.

4. For equipment, include the following in addition to the above, as applicable:

a. Wiring diagrams that show factory-installed wiring. b. Printed performance curves. c. Operational range diagrams. d. Clearances required to other construction, if not indicated on accompanying

Shop Drawings.

5. Submit Product Data before Shop Drawings, and before or concurrent with Samples.

B. Shop Drawings: Prepare Project-specific information, drawn accurately to scale. Do not base Shop Drawings on reproductions of the Contract Documents or standard printed data unless submittal based on Architect's digital data drawing files is otherwise permitted.

1. Preparation: Fully illustrate requirements in the Contract Documents. Include the following information, as applicable:

a. Identification of products. b. Schedules. c. Compliance with specified standards. d. Notation of coordination requirements. e. Notation of dimensions established by field measurement. f. Relationship and attachment to adjoining construction clearly indicated. g. Seal and signature of professional engineer if specified.

2. Sheet Size: Except for templates, patterns, and similar full-size Drawings, submit Shop Drawings digitally formatted on sheets at least 8-1/2 by 11 inches, but no larger than 30 by 42 inches.

C. Samples: Submit Samples for review of kind, color, pattern, and texture for a check of these characteristics with other materials.

1. Transmit Samples that contain multiple, related components such as accessories together in one submittal package.

2. Identification: Permanently attach label on unexposed side of Samples that includes the following:

a. Project name and submittal number. b. Generic description of Sample. c. Product name and name of manufacturer. d. Sample source. e. Number and title of applicable Specification Section.



f. Specification paragraph number and generic name of each item. 3. Web-Based Project Software: Prepare submittals in PDF form, and upload to web-

based Project software website. Enter required data in web-based software site to fully identify submittal.

4. Paper Transmittal: Include paper transmittal including complete submittal information indicated.

5. Disposition: Maintain sets of approved Samples at Project site, available for quality-control comparisons throughout the course of construction activity. Sample sets may be used to determine final acceptance of construction associated with each set.

a. Samples that may be incorporated into the Work are indicated in individual Specification Sections. Such Samples must be in an undamaged condition at time of use.

b. Samples not incorporated into the Work, or otherwise designated as Owner's property, are the property of Contractor.

6. Samples for Initial Selection: Submit manufacturer's color charts consisting of units or sections of units showing the full range of colors, textures, and patterns available.

a. Number of Samples: Submit Three full set(s) of available choices where color, pattern, texture, or similar characteristics are required to be selected from manufacturer's product line. Architect will return submittal with options selected.

7. Samples for Verification: Submit full-size units or Samples of size indicated, prepared from same material to be used for the Work, cured and finished in manner specified, and physically identical with material or product proposed for use, and that show full range of color and texture variations expected. Samples include, but are not limited to, the following: partial sections of manufactured or fabricated components; small cuts or containers of materials; complete units of repetitively used materials; swatches showing color, texture, and pattern; color range sets; and components used for independent testing and inspection.

a. Number of Samples: Submit Three sets of Samples. Architect will retain One Sample sets; remainder will be returned. Mark up and retain one returned Sample set as a project record Sample.

1) Submit a single Sample where assembly details, workmanship, fabrication techniques, connections, operation, and other similar characteristics are to be demonstrated.

2) If variation in color, pattern, texture, or other characteristic is inherent in material or product represented by a Sample, submit at least three sets of paired units that show approximate limits of variations.

D. Product Schedule: As required in individual Specification Sections, prepare a written summary indicating types of products required for the Work and their intended location. Include the following information in tabular form:

1. Type of product. Include unique identifier for each product indicated in the Contract Documents or assigned by Contractor if none is indicated.



2. Manufacturer and product name, and model number if applicable. 3. Number and name of room or space. 4. Location within room or space.

E. Qualification Data: Prepare written information that demonstrates capabilities and experience of firm or person. Include lists of completed projects with project names and addresses, contact information of architects and owners, and other information specified.

F. Design Data: Prepare and submit written and graphic information indicating compliance with indicated performance and design criteria in individual Specification Sections. Include list of assumptions and summary of loads. Include load diagrams if applicable. Provide name and version of software, if any, used for calculations. Number each page of submittal.

G. Certificates:

1. Certificates and Certifications Submittals: Submit a statement that includes signature of entity responsible for preparing certification. Certificates and certifications shall be signed by an officer or other individual authorized to sign documents on behalf of that entity. Provide a notarized signature where indicated.

2. Installer Certificates: Submit written statements on manufacturer's letterhead certifying that Installer complies with requirements in the Contract Documents and, where required, is authorized by manufacturer for this specific Project.

3. Manufacturer Certificates: Submit written statements on manufacturer's letterhead certifying that manufacturer complies with requirements in the Contract Documents. Include evidence of manufacturing experience where required.

4. Material Certificates: Submit written statements on manufacturer's letterhead certifying that material complies with requirements in the Contract Documents.

5. Product Certificates: Submit written statements on manufacturer's letterhead certifying that product complies with requirements in the Contract Documents.

6. Welding Certificates: Prepare written certification that welding procedures and personnel comply with requirements in the Contract Documents. Submit record of Welding Procedure Specification and Procedure Qualification Record on AWS forms. Include names of firms and personnel certified.

H. Test and Research Reports:

1. Compatibility Test Reports: Submit reports written by a qualified testing agency, on testing agency's standard form, indicating and interpreting results of compatibility tests performed before installation of product. Include written recommendations for primers and substrate preparation needed for adhesion.

2. Field Test Reports: Submit written reports indicating and interpreting results of field tests performed either during installation of product or after product is installed in its final location, for compliance with requirements in the Contract Documents.

3. Material Test Reports: Submit reports written by a qualified testing agency, on testing agency's standard form, indicating and interpreting test results of material for compliance with requirements in the Contract Documents.

4. Preconstruction Test Reports: Submit reports written by a qualified testing agency, on testing agency's standard form, indicating and interpreting results of tests performed



before installation of product, for compliance with performance requirements in the Contract Documents.

5. Product Test Reports: Submit written reports indicating that current product produced by manufacturer complies with requirements in the Contract Documents. Base reports on evaluation of tests performed by manufacturer and witnessed by a qualified testing agency, or on comprehensive tests performed by a qualified testing agency.

6. Research Reports: Submit written evidence, from a model code organization acceptable to authorities having jurisdiction, that product complies with building code in effect for Project. Include the following information:

a. Name of evaluation organization. b. Date of evaluation. c. Time period when report is in effect. d. Product and manufacturers' names. e. Description of product. f. Test procedures and results. g. Limitations of use.

1.7 DELEGATED-DESIGN SERVICES

A. Performance and Design Criteria: Where professional design services or certifications by a design professional are specifically required of Contractor by the Contract Documents, provide products and systems complying with specific performance and design criteria indicated.

1. If criteria indicated are insufficient to perform services or certification required, submit a written request for additional information to Architect.

B. Delegated-Design Services Certification: In addition to Shop Drawings, Product Data, and other required submittals, submit digitally signed PDF file paper copies of certificate, signed and sealed by the responsible design professional, for each product and system specifically assigned to Contractor to be designed or certified by a design professional.

1. Indicate that products and systems comply with performance and design criteria in the Contract Documents. Include list of codes, loads, and other factors used in performing these services.

1.8 CONTRACTOR'S REVIEW

A. Action Submittals and Informational Submittals: Review each submittal and check for coordination with other Work of the Contract and for compliance with the Contract Documents. Note corrections and field dimensions. Mark with approval stamp before submitting to Architect.

B. Contractor's Approval: Indicate Contractor's approval for each submittal with a uniform approval stamp or indication in web-based Project software. Include name of reviewer, date of Contractor's approval, and statement certifying that submittal has been reviewed, checked, and approved for compliance with the Contract Documents.



1. Architect will not review submittals received from Contractor that do not have Contractor's review and approval.

1.9 ARCHITECT'S REVIEW

A. Action Submittals: Architect will review each submittal, indicate corrections or revisions required, and return it.

1. PDF Submittals: Architect will indicate, via markup on each submittal, the appropriate action.

2. Physical Samples: Architect will log samples into Web-based Project Software and will indicate, on Project software website, the appropriate action.

3. Submittals by Web-Based Project Software: Architect will indicate, on Project software website, the appropriate action.

B. Informational Submittals: Architect will review each submittal and will not return it, or will return it if it does not comply with requirements. Architect will forward each submittal to appropriate party.

C. Partial submittals prepared for a portion of the Work will be reviewed when use of partial submittals has received prior approval from Architect.

D. Incomplete submittals are unacceptable, will be considered nonresponsive, and will be returned for resubmittal without review.

E. Architect will return without review submittals received from sources other than Contractor.

F. Submittals not required by the Contract Documents will be returned by Architect without action.

PART 2 - PRODUCTS (Not Used)

PART 3 - EXECUTION (Not Used)

END OF SECTION 013300


CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL 017419 - 1

SECTION 017419 - CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section includes administrative and procedural requirements for the following:

1. Salvaging nonhazardous demolition and construction waste. 2. Recycling nonhazardous demolition and construction waste. 3. Disposing of nonhazardous demolition and construction waste.

1.3 DEFINITIONS

A. Construction Waste: Solid waste resulting from construction, remodeling, renovation, or repair operations. Construction waste includes packaging.

B. Disposal: Removal of construction waste and subsequent salvage, sale, recycling, or deposit in landfill, incinerator acceptable to authorities having jurisdiction, or designated spoil areas on Owner’s property.

C. Recycle: Recovery of construction waste for subsequent processing in preparation for reuse.

D. Salvage: Recovery of construction waste and subsequent sale or reuse in another facility.

E. Salvage and Reuse: Recovery of construction waste and subsequent incorporation into the Work.

1.4 MATERIALS OWNERSHIP

A. Unless otherwise indicated, demolition and construction waste becomes property of Contractor.

1.5 DISPOSAL OF WASTE

A. General: Except for items or materials to be salvaged or recycled, remove waste materials from Project site and legally dispose of them in a landfill or incinerator acceptable to authorities having jurisdiction.


CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL 017419 - 2

1. Except as otherwise specified, do not allow waste materials that are to be disposed of accumulate on-site.

2. Remove and transport debris in a manner that will prevent spillage on adjacent surfaces and areas.

B. Burning: Do not burn waste materials.

END OF SECTION 017419

SECTION 120100 FURNITURE, FURNISHINGS & EQUIPMENT

PART 1 - GENERAL

1.1 SUMMARY

A. This section includes, but is not limited to:

1. Fabrication, finish, hardware, delivery to site and installation of standard furnishings, described in Specifications, and as listed below:

a. Stack Chairs b. Guest Chair c. Task Chair d. Executive Chair e. Conference Chair f. Lounge Chair g. Café Stools h. Task Stools i. Ottomans j. Sofas k. Modular Seating l. Multi-Purpose Tables m. Occasional Table n. Accent Tables o. Teacher Tables p. Benching Tables q. Work Tables r. Conference Tables s. Meeting Tables t. Work Bench u. Student Desk v. Teacher Desk w. Administration Desk x. Executive Desk y. Work Station z. Dance Mat aa. Storage Cabinets bb. Storage Cubbies cc. Cash Register Unit dd. 4-Sided Display Cabinet ee. Bookcases ff. Peg Boards gg. 3 Panel Mirror hh. Metal Shelves ii. Lockers jj. Choral Risers kk. Music Chairs

1.2 SYSTEM DESCRIPTION

New Lowndes High SchoolFurniture, Furnishings and Equipment 04-09-2021

Furniture, Furnishings and Equipment 120100-1

A. Furniture Plans and Specifications denote the location of each type of furniture.

B. Quantity of each type of furniture is shown in the specification. Notify the Architect of any discrepancies.

C. Contractor to verify number, size, location and placement of items before order entry, fabrication, and installation.

D. All furnishings that need to be secured to the wall or have bracing system, contractor is to submit for review and approval proposed system for securing.

1.3 SUBSTITUTIONS

A. No substitutions of fabrics allowed.

1. Color for finishes must be approved.

2. Provide required sample of each furniture finish.

1.4 SUBMITTALS: Required once the bid has been awarded

A. Product Data

1. Submit Product Data for each type of furniture indicated including construction and finishing processes as required with submittal.

B. Shop Drawings

1. Shop drawings are required only on non-standard manufacturer’s items or as required by the Specifications.

C. Samples

1. Submit two physical (2) samples (color swatches, etc.) of ALL finish colors and textures including metal finishes, wood finishes, laminate, polypropylene, fabric, etc. For fabric, clearly identify the direction of install.

2. The cost of shipment and return for the proposed submittal item shall be the responsibility of the Contractor.

3. All samples shall be submitted for Architect's approval before application or fabrication.

4. Samples for this section shall be submitted to:

McCall & Associates 3308 Country Club Road Valdosta, GA 31605 Attn: Rhonda Williams

D. Fabric

1. Maintenance Instructions:



a. Submit to Architect, for transmittal to the Owner, (2) copies of the manufacturer's maintenance instructions including information needed for the removal of common stains from each type of fabric and leather used.

1.5 QUALITY ASSURANCE

A. Installer Qualifications

1. Installation shall be performed by personnel that have minimum five years of experience installing furniture of comparable quality with ability to install work to meet specified standards.

2. Furniture Dealer shall provide an on-site supervisor to direct installation of all furniture items.

1.6 DELIVERY, STORAGE & HANDLING

A. Assemble and finish furniture at factory and deliver to site ready for installation.

B. Protect items during delivery, storage and after installation so that there will be no indication of abuse or damage at the time of substantial completion of the Project. Replace or repair damaged Work to showroom condition as directed by the Architect.

C. Materials damaged due to improper protection during storage (dampness included) shall be rejected and removed from the site.

1.7 WARRANTY

A. The items specified herein shall be fully and unconditionally guaranteed by the manufacturer against defects in materials, workmanship and installation for the manufacturer’s standard warranty period after acceptance of installation.

B. Each item has a designated warranty described under each individual furniture category.

PART 2 - PRODUCTS

2.1 GENERAL

A. Furniture Location

1. Refer to Furniture Specifications for furniture locations.

2.2 FINISHES

A. Selected manufacturers of finishes and fabrics are those listed within each item appearing in the Furniture Specification.



2.3 FURNITURE – Each piece of furniture shall have an affixed furniture tag which shall include at least the following information:

a. Purchase Order Number b. Purchase Order Line Item Number c. Model Number d. Color e. Fabric f. Manufacture Date g. Ship Date



2.3.1 CHAIRS

A1 Stack Chair A2 Stack Chair A3 Stack Chair Wall Saver A4 Stack Chair A5 Stack Chair With Upholstery A6 Guest Chair with Wood Legs Chair A7 Guest Chair with Upholstery A8 Guest Chair with Upholstery and Casters A9 Guest Chair with Upholstery A10 Guest Chair with Upholstery A11 Guest Chair A12 Task Chair A13 Task Chair A14 Task Chair A15 Executive Chair A16 Conference Chair A17 Lounge Chair A18 Lounge Chair A19 Lounge Chair A20 Lounge Chair A21 Music Chair



A1: Stack Chair

Basis-of-Design: Manufacturer: KISeries: Intellectual Wave ChairModel No: IWC18Description: Armless side chair. One-piece seat and back

contoured shell made of high impact polypropylene. Dual wall structure where seat and back meet.Complete color impregnation throughout the molded part. Engineeredinternal structural cavity. Wide, ergonomic handle molded into chair back.Frame consist of 3/4" x 1-1/2" O.D. 14 gauge elliptical tubing welded to a 14 gauge steel plate. Finished in a powder-coated paint after all weldingprocesses are complete.

Dimensions: Large: 20.3"W x 19.6"D x 32"HBase Style: Cantilever Base Color: (SX) Starlight SilverCut Out: Handle Shell Style: PolypropyleneShell Color: See list below.Glides: Felt / Nylon - See list belowWarranty: 15 Year

Glides Color Room# QtyFelt PCY Cayenne 1047(4), 1048(4), 1050(4),1064(32) 44Felt PSP Surf's Up 1091(12), 1093(12), 2010(32), 2017(32) 88Felt PGN Grass Green 1091(8), 1093 (8) 16Felt PSK Sky Blue 1091(6), 1093(6) 12NylonNylon PCY Cayenne 2nd Floor 34 Typical Classrooms (32 ea. Classroom) 1,088

3rd Floor 33 Typical Classrooms (32 ea. Classroom) 1,0561051(32), 1052(32),2009(32),2103(30),2104(30),2107(36) 1922108(32)3004(32),3009(32),3016(32),3087(32), 1603088(32), 3097(32), 3098(32),3104(32), 3105(24) 152

In compliance with the intent and requirements of these Bidding Documents, provide the Basis-of-Design Product described below.

Substitution of a comparable product by one of the approved manufacturers listed below may also be considered if Vendor submits a Substitution Request which strictly complies with requirements listed in Specification Section 002600 - Procurement Substitution Procedures.

1. VS America



A2: Stack Chair

Basis of Design:Manufacturer: KISeries: Strive Stack Chair (Armless)Description: Backrest is slotted, injected-molded polypropylene with integral steel cantilever springs.

The slotted polypropylene back and the spring steel provides a supportive flexing back. Springs are nominal 4.5mm diameter chrome silicon valve spring wire. Seat and shroud areinjected polypropylene . Legs are 7/8" O.D. by 13 gauge tubular steel. Cross members are 1" O.D. by 14 Gauge Tubular steel and 7/16" diameter solid steel. All joints are welded.400 lb. weight capacity. Frames are baked on electrostatically-applied 30-degree glossepoxy-coated paint. Upper and lower ends of leg tubes are capped with polypropylene end caps matching leg color

Dimensions: 21 3/4" D x 32 1/2" H20 5/8" W (rear leg width)18" W (front leg width)Seat 18" H

Frame Style: See Chart BelowFrame Color: (SX) Starlight SilverGlides: Swivel Felt, Swivel Poly/Nylon - See list belowWeight Capacity: 400 lbs.Shell Style: Molded polypropyleneShell Color: PCY-Cayenne, PRG-Blue Grey, PCP-Surf's UpWarranty: 15 Year

Model No. Glides Color Room# Base QtySLNAP Felt PCY Cayenne 1008 (6), 1021(5), 1022(5), 1043 (2) 4 Leg 18SLNAP Felt PRG Blue Grey 1008(6), 1064(10), 1024(3) 4 Leg 19SLNAP Felt PCP Surf's Up 1092(4) 4 Leg 4

SLNAP Nylon PRG Blue Grey 1067(54), 1084(48), 1085(34), 1086(24), 1087(16) 4 Leg 4622103 (10), 2104(10), 2106(16), 2107(16)3004(32), 3009(32), 3087(32), 3088(32) 3097(32), 3098(32), 3105(26), 3106(16),


Substitution of a comparable product by one of the approved manufacturers listed below may also be

Specification Section 002600 - Procurement Substitution Procedures.



Model No, Color Room# Base QtySPDNAP Sand 2012 5 Star 3



A3: Stack Chair:

Basis of Design:Manufacturer: KISeries: Strive Chair (Wall Saver)Model No: SLNAP(WS)

Description: Backrest is slotted, injected-molded polypropylene with integral steel cantilever springs. Springs are nominal 4.5mm diameter with chrome silicon valve spring wire. Seat and shroud are injected polypropylene . Legs are 7/8" O.D. by 13 gauge tubular steel. Crossmembers are 1" O.D. by 14 Gauge Tubular steel and 7/16" diameter solid steel. All joints are welded. 400 lb. weight capacity. Frames are baked on electrostatically-applied30-degree gloss epoxy-coated paint.


Frame Style: 4 Legs Wall SaverFrame Color: (SX) Starlight SilverGlides: NylonShell Style: Molded polypropyleneShell Color: See Chart BelowWarranty: 15 Year

Glides Color Room# QtyNylon PCY Cayenne 1049(4),1057(2),1059(2),1064A(2),2008(2) 3007(2), 22

3008(2),3010(2),3089(1),3092(1), 3093 (1), 3096(1)Nylon PGR Blue Grey 2011(1), 2016(1), 2080(2), 2090(2), 2091(2), 9

2092(1)Felt PCP Surf's Up 1109(3) 3

1. VS America





A4: Stack Chair

Basis of Design:Manufacturer: KISeries: Doni Chair Model No: DNI100Description: The backrest and seat are injection-molded polypropylene.

The seat and backrest are joined by a pair of hidden articulation mechanisms,each consisting of a 14-gauge steel housing, twin 7-gauge levers and steel coil springs. While maintaining a one-piece shell appearance, this mechanism allowsthe backrest to recline up to 17 degrees of motion.Tapered Steel Leg BaseA seat ring is made of 1/2” diameter steel wire and attached to the seat with 14-gauge steel brackets. Inner leg wires are made of 1/2” diameter steel wire and areplug welded to tapered tubular legs. All joints are welded and the frames arefinished in either baked-on electrostatically-applied epoxy powder-coat paint.

Dimensions: 19-3/8"W x 21"D x 33-3/4"HBase Style: Steel Legs Epoxy Powder Coated PaintBase Color: (SX) Starlight SilverWeight Capacity: 400 lbs.Shell Style: High Impact PolypropyleneShell Color: See list below.Glides: Swivel FeltWarranty: 15 Year

Color Model # Room# QtyOuter Shell: DNI 100 1008 12PCY CayenneInner Shell:PCG Cool GreyOuter Shell: DNI 100 1127 9PCO CottonwoodInner Shell:PCY Cayenne





A5: Stack Chair

Basis of Design:Manufacturer: KISeries:Model No: DNW200Description:

Dimensions:Base:Base Color:Shell Style:Shell Color:Glides:Warranty:Weight Capacity:

See Fabric Below

Note: Image is for reference only; see above specification for exact model information.

Fabric Seat:Manufacturer:Pattern/Color:Repeat: 1099 20Content:Width:Finish/Backing:Warranty:Flammability:Abrasions:



A6: Stack Chair:

1. Herman Miller2. Steelcase

Basis of Design:Manufacturer: KISeries: Doni Chair UpholsteredModel No: DNW200Description: Injected polypropylene Guest Chair with upholstered seat.

The backrest and seat are injection-molded polypropylene.The seat and backrest are joined by a pair of hidden articulation mechanisms,each consisting of a 14-gauge steel housing, twin 7-gauge levers and steel coil springs. While maintaining a one-piece shell appearance, this mechanism allowsthe backrest to recline up to 17 degrees of motion.Upholstered SeatUrethane foam is attached to an injection-molded polypropylene liner board,then upholstered using a draw-string process. Seat foam is molded nominal 1”thickness, and back foam is nominal 1/2” thickness. Wood Leg BaseThe seat plate is die-cast aluminum, finished with baked-on electrostatically-appliedepoxy powder-coat paint. Legs are turned from Beech, stained, and clear-coat finished.A steel insert with tapped end is inserted and pinned in each leg, then each legassembly is attached to the seat plate with one 1/4-20 screw. X-brace is made of twozinc plated steel cable assemblies that attach to the legs with #10-24 screws.

Dimensions: Dimensions: 19-3/8"W x 21"D x 33-3/4"HBase: Wood Legs with Steel Frame Base Color: NaturalShell Style: High Impact PolypropyleneShell Color: PWG Warm GreyGlides: Swivel /FeltWarranty: 15 YearWeight Capacity: 400 lbs.


Color Model # Room# QtyOuter Shell: DNI 100 2046(20), 2059,(20) 120PCY Cayenne 3044(20), 3057(20)Inner Shell: J-Wing (20) PWS Wet Sand E-Wing (20)





A7: Guest Chair


Basis of Design:Manufacturer: All SeatingSeries: Inertia Upholstered Chair with ArmsModel No: 79454-NA-BK-CA--G7-(6)-F-LNEUT-FA-ASDescription: Upholstered back and seat, tubular steel frame, unique shape nylon arms.

Fully upholstered side chair with 1.5" seat foam and nylon arms.350 Lbs. weight limit.

Base: 4 Legs Base Color: Black NylonArms: Black NylonWarranty: 12 Year Comprehensive Parts and Labor

Fabric Back:Manufacturer: MomentumName: PointColor: SlateContent: 58% Post Consumer Recycled Polyester, 42% Post Industrial Recycled PolyesterRepeat: 12-3/8" V, 7-1/8" HWidth: 54"Finish/Backing: Greensheild/AcrylicWarranty: 3 YearsFlammability: NFPA - 260 TB 117Durability: 60,000 Double Rubs

Fabric Seat :Manufacturer: PallasName: Haven/Storm 27.291.132Content: 100% SiliconeRepeat: NoneWidth: 54"Finish/Backing: NoneWarranty: 5 YearFlammability: NFPA-260 TB 117-2023Durability: 100,000 Double Rubs


Dimensions Room# Qty32"H x 18"W x 24"D 1116(4), 1119 (4), 1122 (4) 20

1123(4), 1126(4)





Fabric Back:Manufacturer: MomentumName: PointColor: PewterContent: 58% Post Consumer Recycled Polyester, 42% Post Industrial Recycled PolyesterRepeat: 12-3/8" V, 7-1/8" HWidth: 54"Finish/Backing: Greensheild/AcrylicWarranty: 3 YearsFlammability: NFPA - 260 TB 117Durability: 60,000 Double Rubs

Fabric Seat :Manufacturer: PallasName: Nappa/Concrete 27.240.122Content: 100% SiliconeRepeat: NoneWidth: 54"Finish/Backing: NoneWarranty: 5 YearFlammability: NFPA-260 TB 117-2023Durability: 100,000 Double Rubs


Dimensions Location Qty32"H x 18"W x 24"D 1114(2), 1115(2),1117(4), 20

1120(4),1124(4),1125(4)



A8: Guest Chair:

Basis of Design:Manufacturer: All SeatingSeries: Inertia Upholstered Chair with ArmsModel No: 79454-NA-BK

Description: Upholstered back and seat, tubular steel frame, unique shape nylon arms.Fully upholstered side chair with 1.5" seat foam and nylon arms.350 Lbs. weight limit.

Base: 4 Legs with castersBase Color: Black NylonArms: Black NylonWarranty: 12 Year Comprehensive Parts and Labor

Fabric Seat & Back:Manufacturer: MomentumName: HobnobColor: CannonContent: 51% Recycled Polyester,49% PolyesterRepeat: NoneWidth: 56"Finish/Backing: CryptonWarranty: 3 YearFlammability: NFPA-260 TB 117-2023, CA Bulletin 117 2013Durability: 87,000 Double Rubs


Dimensions Room# Qty32"H x 18"W x 24"D 1118 6





A9: Guest Chair:


Basis of Design:Manufacturer: KISeries: AffinaModel No: 1901/FC

Description: Frames are hardwood and joints are mortised or doweled and gluedLegs and wood arm caps are beech hardwoodSeat suspension is sprung with stretch strap webbing staples into positionField-replaceable backs and arm caps

Dimensions: 23.5" x 23.5"D x 31.5"HBase Color: CinnamonWarranty: 15 Year

Fabric Seat:Manufacturer: PallasPattern/Color: Trellis/ObsidianRepeat: 24-3/4"V, 14-1/2"HContent: 100% PolyesterWidth: 54"Finish/Backing: Nanotex/AcrylicWarranty: 3 YearsFlammability: 260 TB 117Abrasions: 70,000 Double Rubs

Fabric Seat:Manufacturer: PallasPattern/Color: Aphrodite/Storm Cloud 27.258.112Repeat: NoneContent: 100% Poly Vinyl ChlorideWidth: 54"Finish/Backing: Greensheild/AcrylicWarranty: 3 YearsFlammability: 260TB 117-2013Abrasions: 250,000 Double Rubs


Glides Room# QtyFelt 1121 6





A10: Guest Seating

1. Herman Miller

Basis of Design:Manufacturer: Indiana FurnitureSeries: GleemModel No: 395

Description: High grade CAL 117-2013 polyurethane foam 5-1/2" thick in the seat and 4-3/4 " thick in the back. Internal wood components are manufactured using plywood while chair frames are manufactured using Maple; all chair joints are mortised and tenoned, screwed and glued for maximum Strength and durability. Legs are 10" tall; non-marring nylonincluded in each leg at floor level.

Dimensions: 23-3/4"W x 24"D x 31-3/4"HWood Base: Artisan Walnut (AW)Arms: ArchWarranty: 12 Year

Fabric Seat & Back:Manufacturer: PallasPattern: Louver/Ship 27.287.022Content: 40% Cotton, 35% Rayon, 25% NylonWidth: 54"Finish/Backing: Teflon/AcrylicFlammability: NFPA 260, TB 117-2013Abrasions: 85,000 Double RubsRepeat: REPEAT 6-7/16" V, 7" HWarranty: 3 Year


Model # Room# Qty395 1137 6





A11: Guest Chair

1. Herman Miller

2. Steelcase

Basis of Design:Manufacturer: KISeries: KateraModel No: KT1311Description: Upholstered Seat & Back Seat

Foam is molded to a nominal 15 mm thickness, attached to an injection-moldedpolypropylene liner board, then upholstered using a draw string process. Backfoam is a nominal 5 mm thickness and is attached to an injection-moldedpolypropylene liner. The liner and foam are then inserted into an upholsteredcover and secured with heat activated glue. The upholstered backs are finished onthe lower edge with a black zipper.4-Leg Frames Legs frames are made from 1.9 mm thick tubular D-shaped(3 /4” x 1”) steel. Steel wire and U-channels form the crossmembers. All joints arewelded. Aluminum support brackets are inserted in the rear legs and allow thebackrest of the chair to be secured. The support bracket hardware is concealed bya polypropylene cap, color matched to the frame paint. When chrome is selected,the caps will be chromed metal. Café Stool Frames Café Stool models are availablein 4-leg frames, and in 24” and 30” seat heights. Frames are equipped with areinforcing footring made of 17 mm diameter tube, which is welded to the tubularframe and open in the back. Stool models do not stack. Frame Finishes Frames arefinished in either powder-coat paint, or bright nickel-chrome plating. The aluminumback supports are painted to match the frame color and will be polished when chromeplating is chosen. Arms Optional armrests are available. The armrests are injection-molded glass-reinforced polypropylene matching the frame finish (when frame finishis Chrome, arm color will need to be specified). The front of the arms include a steelinsert for greater strength and method of attachment. The front part of the arms areinserted into the front legs of the chair and secured with screws. The rear part of thearms are inserted into the aluminum backrest support and secured with screws.Glides The leg tubes are capped with D-shaped (7 /8” x 11 /8”) polypropylene end capglides where legs meet the floor. The four caps are different, depending on the leg inwhich they are inserted, due to the different shape of each leg. Each cap is numberedand includes notches to differentiate their placement. Cap color is always black.

Dimensions: 23"W x 21-3/4" x 31-1/4"Base Style: SteelBase Color: CG Cool GreyWeight Capacity: 350Glides: NylonWarranty: 15 Years





Fabric Seat:Manufacturer: PallasPattern/Color: Haven/Greyhound 27.291.122Repeat: NoneContent: 100% SiliconeWidth: 54"Finish/Backing: NoneWarranty: 5 yearFlammability: NFPA 260, TB 117-2013,ASTME-84Abrasions: 100,000 Double Rubs

Fabric Back:Manufacturer: PallasPattern/Color: Utopia/Fog 27.278.052Repeat: NoneContent: 39% Recycled Solution-Dyed Nylon, 36% Rayon, 25% PolyesterWidth: 54"Finish/Backing: Nanotex/AcrylicWarranty: 3 yearFlammability: NFPA 260, TB 117-2013Abrasions: 100,000 Double Rubs

Model # Room# QtyKT1311 2027(2),2064(2) 24

2079(2), 2086(4)3024(2), 3062(2)3078(2), 3079(2)3083(4), 1075(2)



A12: Task Chairs


Basis of Design:Manufacturer: KISeries: Oath Task Chair with ArmsModel No: OH84QBDescription: A weight-activated mechanism adjusts backrest tilt tension based on occupant

weight. The mechanism is made of stamped steel with a black plastic trim cover.Seats are plywood seat board with molded urethane foam is upholstered usinga drawstring method and finished with a black plastic under-shroud. BackrestReinforced black nylon frame with mesh insert. Casters are 50mm O.D., double-wheel high-impact thermoplastic. Optional height-adjustable arms are molded in black reinforced plastic with molded black polyurethane arm caps. Armrests mountdirectly to the seat board. Foot Ring Task stools are equipped with an adjustable-height foot ring with black, die-cast aluminum hub and spokes, with an 18" diameterchrome-plated tubular steel ring.

Dimensions: 26" W x 27" D39 1/2" - 44" adjustable overall H16 1/2" - 21" adjustable seat H

Base: Black Star Base with CastersCasters: See Chart BelowSeat: Plywood board with molded urethane foam upholsteredSeat Colors: See Chart below.Backrest: Black MeshWarranty: 15 Years

Fabric Seat:Manufacturer: PallasName: See Charts BelowContent: 58% Polyester, 31% Post Consumer

Recycled Polyester, 11% NylonRepeat: 14-3/4" V, 14-1/2"HWidth: 54"Finish/Backing: Pinnacle/AcrylicWarranty: 3 YearFlammability: NFPA 260, TB 117-2013Durability: 105,000 Double Rubs






Casters Color Room# QtyHard MOD/Chili 27.304.148 2nd Floor Typical Classroom 34Hard MOD/Chili 27.304.148 2103, 2104, 2107, 2108 4

Hard MOD/Chili 27.304.148 3rd Floor Typical Classroom 33Hard MOD/Chili 27.304.148 3004, 3009, 3016, 3087, 4Hard MOD/Chili 27.304.148 3088, 3097, 3098, 3104, 3105 5

Soft MOD/Fog 27.304.042 2010,2017 2

Fabric Seat:Manufacturer: PallasPattern/Color: See Chart BelowRepeat: NoneContent: 100% SiliconeWidth: 54"Finish/Backing: NoneWarranty: 5 yearFlammability: NFPA 260, TB 117-2013,ASTME-84Abrasions: 100,000 Double Rubs


Casters Color Room# QtyHard Haven/Storm 27.291.132 1075,1085(2), 2027, 2064, 2079, 12

2086, 3024, 3062, 3078, 3079, 3083

Soft Haven/Crimson 27.291.258 1127 6

Fabric Seat:Manufacturer: KIName: LineateColor: PewterContent: 100% Vinyl with Nylon BackingRepeat: NoneWidth: 54"Finish/Backing: Permablock 3Warranty: 3 YearFlammability: CFFA 1, ASTM D-4157-02Durability: 100,000 Double Rubs


Casters Color Room# QtyHard Lineate/Pewter 1051 (1, )1052(1) 2Soft Lineate/Pewter 1050 (1) 1



Fabric Seat:Manufacturer: PallasName: Bounce/True Blue 27.160.114Content: 100% PolyurethaneRepeat: NoneWidth: 54"Finish/Backing: Sta-KleenWarranty: 3 YearFlammability: NFPA 260TB 117-2013Durability: 500,000 Double Rubs


Casters Color Room# QtySoft Bounce/True Blue 1091(1),1093(1) 2



A13: Task Chairs


Basis of DesignManufacturer: KISeries: Diem ChairModel No: See Chart BelowDescription: A weight-activated mechanism passively adjusts backrest tilt tension based on occupant weight.

The mechanism is made of stamped steel with a black plastic trim cover. One lever operates theheight-adjust cylinder and a second lever allows the backrest tilt mechanism to move freely, or locks it in one of four positions. Plywood seat board with 3-1/2" thick molded urethane foam is upholstered using a drawstring method. Reinforced nylon frame with mesh insert. Chairs andstools have an injection-molded, glass-reinforced black nylon 5-blade base. Caster are 55mm are 55 mm O.D., double-wheel high-impact thermoplastic, and are designed for use on bothcommercial carpet and hard floors. Stools are equipped with an adjustable-height foot ring withwith black, die-cast aluminum hub and spokes, with an 18” diameter chrome-plated tubularsteel ring. Optional height-adjustable arms are molded in black reinforced plastic with molded black polyurethane arm caps. Armrests mount directly to the seat board. Task stools areequipped with an adjustable-height foot ring with black, die-cast aluminum hub and spokeswith an 18” diameter chrome-plated tubular steel ring.

Base:Casters: ThermoplasticBack: Black MeshArms: 1DWarranty: 15 Years

Fabric Seat:Manufacturer: KIName: LineateColor: PewterContent: 100% Vinyl with Nylon BackingRepeat: NoneWidth: 54"Finish/Backing: Permablock 3Flammability: CFFA 1, ASTM D-4157-02Durability: 100,000 Double RubsWarranty: 3 Year


Model # Casters Dimensions Room# QtyTask Chair KIDE82C Hard 27W X 27"D x 38-43"H 1049(2), 1057, 1059, 1064A 27

1079(2),2008, 2011, 2016, 2080,2090, 2091, 2092, 3007(2),3008(2), 3010, 3017(4),3089,3092, 3093, 3096

Task Stool KIDE92C Soft 27W X 27"D x 43-51"H 1014(2), 3017 (4) 6





A14: Task Chair

Basis of Design:Manufacturer:Series:Model No:Description:

Dimensions:Controls:Base:Casters:Back:Warranty:

Fabric:Manufacturer: PallasPattern/Color: Haven/Greyhound 27.291.122Repeat: NoneContent: 100% SiliconeWidth: 54"Finish/Backing: NoneWarranty: 5 yearFlammability: NFPA 260, TB 117-2013,ASTME-84Abrasions: 100,000 Double Rubs


Room# Qty23



A15: Executive Chairs


Basis of Design:Description: Ergonomic curved back provides lumbar support and promotes circulation.

Stand with swivel tilt control wit adjustable tension. Pneumatic Heightadjustment. Fiberglass reinforced nylon base. Black height adjustableT-arms and black dual wheel carpet casters.

Manufacturer: IndianaSeries: ClutchModel No: 584-ABT2-SW-BLKBase: 5 Star BaseDimensions: 26"W x 26"D x 43-48"HBase: Black Nylon BaseCasters: Black Dual Wheel Carpet CastersWarranty: 12 Year


Fabric Manufacturer Fabric Pattern/Color Room# QtyPallas Nappa/Gotham 27.240.132 1136 1

Pallas Nappa/Portobello 27.240.051 1137 1





A16: Conference Chair

Basis of Design:Manufacturer:Series:Model No:

Description:

Dimensions:Base:Casters:Arms:Warranty:


141141 14



A17: Lounge Chair

1. VS America2. Steelcase

Basis of Design:Manufacturer: KISeries: Sway ChairModel No: SYCNC

Description: Lounge Chair Seat and Base Frame Construction The seat and 4-leg base framesare made of rotationally molded Linear Low Density Polyethylene. The rotatingcontact surface that attaches to the underside of the seat frame consists o a spun12-gauge steel . The base has 12 gliding posts made of Ultra High Molecular Weight Polyethylene which resist wear to over 100,000 cycles in testing. The gliding postsare field replaceable should they show wear over their lifetime. The Seat and Backrest Upholstery shells are made of post-consumer recycled thermoplastic. The fully upholstered shells are fastened to the seat using 3/8"diameter nylon ribbed friction lock rivets. The table's 4-leg base is LLDPE rotationallymolded, with a supporting structure made of spun 12-gauge steel.The Side Table top is 3/4" thick, 45 lb. density built-up particle board with a totalthickness of 3". Overwrapping the sides and top of the wood construction is .030"thick high pressure laminate. The seat foam pad is a molded single piece, with anaverage of 3.5 lb. density and 45 IFD value at 3” thick. The back foam is slab cut, withan average 1.9 lb. density and 34 IFD value at 1” thick.

Dimensions: 33" W x 32.5"D x 41.75"HShell: PCG Cool GreyBase: NylonWarranty: 15 Year

Fabric Back:Manufacturer: PallasPattern/Color: Aphrodite/Storm CloudContent: 100% Poly Vinyl ChlorideWidth: 54"Finish/Backing: ResilienceWarranty: 3 YearFlammability: NFPA- 260 TB 117-2013 Abrasions: 500,000 Double RubsRepeat: None

*Furniture image is not a representation of fabrics. See specifications

Model # Room# QtySYCNC 1085 4





A18: Lounge Chair


Basis of Design:Manufacturer: KISeries: My WayModel No: See Chart Below

Description: Frame Construction—Frames and ArmsFrames and Arms are constructed of 6/4 lumber kiln dried to a moisturecontent of six to eight percent and laminated hardwood plywood ¾” inthickness. All mainframe joints are doweled or interlocked and glued. Stress points are further reinforced with the use of glued and screwedcorner blocks.Suspension—Seat and BackThe seat and back are sprung with stretch webbing stapled into positionand covered with a layer of FLW (reinforced non-woven fiber sheet)Foam SpecificationsSeats and BacksTight seats and backs are filled with a layer of 4” polyurethane foam witha density of 2.5 and a compression of 35 pounds. This foam is covered witha layer of ¼” super soft foam. Arm tops are 1-1/2” thick polyurethane foamwith a density of 4.6 and compression of 150 lbs. ¼” polyurethane foam isaround the entire arm and has a 1.5 density and 45 pound compression.

Base ConstructionSled bases are 1” O.D. x 16 gauge round steel tubing welded to a 14 gaugesteel mounting plate. Bases are secured to the lounge frame with #10 x 1.5”steel pan head wood screws. Powder coat paint is standard.is standard.

Dimensions: 36"W x 34.5"D x 29.5" Base: SledBase Color: SX Starlight SilverWarranty: 15 Year

Note: Image is for reference only; see specification for exact model information.





Fabric Back & Seat:Manufacturer: Arc-Com AC 61549Pattern: ItajimeColor: Fog #10Content: 100% Post Industrial Recycled Solution Dyed NylonRepeat: 13-3/4H x 10VWidth: 54"Finish/Backing: Stain Resistant/Acrylic BackingWarranty: 3 YearFlammability: ASTM E-84, NFPA 255, UL #723Abrasions: 100,000 Double Rubs

Fabric Arms:Manufacturer: PallasPattern/Color: Aphrodite/Storm Cloud 27.258.112Repeat: NoneContent: 100% Poly Vinyl ChlorideWidth: 54"Finish/Backing: ResilienceWarranty: 3 YearsFlammability: 260TB 117-2013Abrasions: 250,000 Double Rubs

Model # Description Room# Qty

MYHN/FC Left Facing High Arm 1006 4Right Facing No Arm

MYNH/FC Left Facing No Arm 1006 4Right Facing High Arm

MYLL/FC Left Facing Low Arm 1009 4Right Facing Low Arm



Fabric Back & Seat:Manufacturer: Arc-Com AC 16542Pattern: ItajimeColor: Ruby #3Content: 100% Post Industrial Recycled Solution Dyed NylonRepeat: 13-1/4H x 1)VWidth: 54"Finish/Backing: 100% PolyesterFlammability: ASTM E-84, NFPA 255, UL #723Abrasions: 100,000 Double RubsWarranty: 3 Year

Fabric Seat:Manufacturer: PallasPattern/Color: Haven/Flame Repeat: NoneContent: 100% SiliconeWidth: 54"Finish/Backing: 18oz. / Linear yardWarranty: 5 yearFlammability: NFPA 260, TB 117-2013,ASTME-84Abrasions: 100,000 Double RubsWarranty: 3 Year

Model # Description Room# Qty

MYHN/FC Left Facing High Arm, 1006 2Right Facing No ArmLeft Facing No Arm, 1006 2Right Facing High Arm



A19: Lounge Seating


Basis of Design:Manufacturer: KISeries: HUBModel No: H43/FC:NPSADescription: All legs are constructed of 1” O.D. x 16-gauge round steel tubing welded to

14-gauge steel mounting plate and secured to the frame with 16 #10 x 11 /2”steel pan head wood screws. Optional glides are clear Polycarbonate press-fitto the underside of the metal tubing.Backrest supports are 1-1 /8” O.D. 16-gauge for lounges with laminated transom,or 12-gauge steel tubing inserted over 7 /8” O.D., 16-gauge steel tubing, for allfully upholstered models. Backrest supports are fastened to the wooden loungeframes using 1 /4-20 steel bolts into steel threaded inserts,The seat is constructed with stretch strap webbing, inner woven and stapled intoposition. Both seats and backs are covered with a layer of FLW (reinforced non-woven fiber) on top.The back foam has a density of 1.5 and compression of 26 lb. foam that is3” thick and contour cut for consistency. The seat foam is 6” thick with adensity of 2.5 and compression of 45 lb. A .5” super soft wrap covers thefront and top of the seat.

Dimensions: 26"D x 78"W x 30-1/4""HBase: Sled BaseWarranty: 15 Year





Fabric Back:Manufacturer: PallasPattern/Color: Fuse/ Huskie 27.303.112Content: 52% Polyester, 36% Post Consumer Recycled Polyester, 12% NylonRepeat: 7-3/8" V, 7-1/8" HWidth: 54"Finish/Backing: Ease/AcrylicWarranty: 3 YearFlammability: NFPA 260, Class 1, TB 117-2013Abrasions: 102,000 Double Rubs

Fabric Seat:Manufacturer: PallasPattern/Color: Burnish /Surf 27.314.124Repeat: NoneContent: 95% Polyurethane, 5% SiliconeWidth: 54"Finish/Backing: Writer's Block/100% PolyesterWarranty: 3 yearFlammability: NFPA 260, TB 117-2013Abrasions: 250,000 Double Rubs


Model # Room# QtyS20278976 1085 6

e

or exact model information.



A20: Lounge Seating


Basis of Design:Manufacturer: Indiana FurnitureSeries: Portia Lounge ChairModel No: 576 Club Chair

Description: High grade CAL 117-2013 polyurethane foam 51/2" thick in the seat and 43/4" thick in the back Internal wood components are manufactured using plywood, while chair frames are manufactured using Maple; all chair joints are mortised and tenoned, screwed and glued for maximum strength and durability; legs are 10" tall; non-marring nylon glides included in each leg at floor level.

Dimensions: 31"W x 30" D x 34"H Wood Base: Artisan Walnut (AW)Warranty: 12 Year

Fabric Seat, Back& Arms:Manufacturer: Arc-Com AC62332Pattern: LegendColor: Fog #3Content: 64% Polyester, 36% Acrylic

Width: 54"Finish/Backing: Alta Performance TechnologyFlammability: ASTM E-84 (adhered), NFPA 255, UL #723, UBC #8-1 Rated. 2) Meets the

requirements of the San Francisco Bureau of Building Inspection. 3) State of California Bulletin #117-2013. 4) UFAC Class 1/NFPA 260. 5

Abrasions: 100,000 Double RubsRepeat: NoneWarranty: 3 Year


Model # Room# Qty576 1137 2





A21: Music Chair

1. KI2. Steelcase

Basis of Design:Manufacturer: WengerSeries: NotaModel No: Standard Nota Chair

Description: Narrow convex back provides lumbar support while still allowingfor freedom and range of movement. Rounded waterfall front

polypropylene seat and back promote even weight distribution, greater comfort

Chrome also available. Durable, specially designed floor glides provide stabilitywhen seated and ease of movement when arranging chairs Specially designedstacking bumpers provide maximum stability and protection when chairs are

Dimensions: 19"Chair Color: BlackBase Color: BlackWarranty: 5 Year

Room# Qty.Chairs 1019 50Dolly 1019 3Chairs 1029 70Dolly 1029 4

Substitution of a comparable product by one of the approved manufacturers listed below may also be considered if Vendor submits a Substitution Request which strictly complies with requirements



2.3.2 STOOLS

B1 Café Stool B2 Polypropylene Stool B3 Task Stool



B1: Café Chair


Basis of Design:Manufacturer: KISeries: Apply Café StoolModel No: ALHSP

Description: One-piece contoured wood shell is constructed of formed plywood, .460”-.480” thick,7-ply maple and poplar construction. Top/bottom and front/back surfaces are vertical grade post forming high-pressure laminate.Legs are formed from 3/4” O.D. by 13-gauge tubular steel. The seat plate is formedfrom 12-gauge steel and reinforced with 7/16" diameter wire cross member. All jointsare welded.

Dimensions: 18-3/4"W x 23-3/4"D x 44-3/4"HSeat Height: 29-3/4"Base Color: SX Starlight SilverShell Style: High BackGlides: Felt Warranty: 15 Year


Glides Room# QtyNylon 1085 12Felt 1085A 13





B2: Polypropylene Stool

1 VS America2. Steelcase

Basis of Design:Manufacturer: KISeries: StriveModel No: SLSNAU

Description: Backrest is slotted, injected-molded polypropylene with integral steel cantilever springs. The slotted polypropylene back and the spring steel provides a supportive flexing back. Springs are nominal 4.5mm diameter chrome silicon valve spring wire. Seat and shroud areinjected polypropylene . Legs are 7/8" O.D. by 13 gauge tubular steel. Cross members are 1" O.D. by 14 Gauge Tubular steel and 7/16" diameter solid steel. All joints are welded.400 lb. weight capacity. Frames are baked on electrostatically-applied 30-degree glossepoxy-coated paint. Upper and lower ends of leg tubes are capped with polypropylene end caps matching leg colorStool-height units are equipped with a reinforcing foot ring made of a 1/2”diameter wire ring, which is open in the back to allow stacking of armless and cantilever arm stools.


Weight Capacity: 400 lbs.Frame Color: (SX) Starlight Silver gloss epoxy powder-coatGlides: Swivel Felt, Swivel Poly/Nylon - See list belowShell Color: See list below.Warranty: 15 Year

Glides Color Room# QtyFelt PCY-Cayenne 1015(1),1023(2),1024(4), 1055(32), 1063(32), 3013(2), 77

3014(2), 3015(2)Felt PCG-Blue Grey 1064 8





B3: Task Chairs


Manufacturer: KISeries: Oath Task Stool with ArmsModel No: OH94QB

Description: A weight-activated mechanism adjusts backrest tilt tension based on occupant weight. The mechanism is made of stamped steel with a black plastic trim cover.Seats are plywood seat board with molded urethane foam is upholstered usinga drawstring method and finished with a black plastic under-shroud. BackrestReinforced black nylon frame with mesh insert. Casters are 50mm O.D., double-wheel high-impact thermoplastic. Optional height-adjustable arms are molded in black reinforced plastic with molded black polyurethane arm caps. Armrests mountdirectly to the seat board. Foot Ring Task stools are equipped with an adjustable-height foot ring with black, die-cast aluminum hub and spokes, with an 18" diameterchrome-plated tubular steel ring.

Basis of Design:Dimensions: 26"W x 27"D x 23"HBase: Black Star Base with CastersCasters: See Chart BelowSeat Colors: See Chart below.Backrest: Black MeshWarranty: 15 Year

Fabric:Manufacturer: PallasPattern/Color: Haven/Flame 27.291.268Repeat: NoneContent: 100% SiliconeWidth: 54"Finish/Backing: NoneWarranty: 5 yearFlammability: NFPA 260, TB 117-2013,ASTME-84Abrasions: 100,000 Double Rubs


Casters Fabric Pattern/Color Room # QtyHard Haven/Flame 27.291.268 2009 1Soft Haven/Flame 27.291.268 1055, 1063 2

Fabric Mfg. Fabric Pattern/ColorPallas Soft Mosaic/Slate 27.220.132 1064 1





2.3.3 OTTOMANS

C1 Rectangular Ottoman C2 Curved Ottoman



C1: Lounge Seating

1. FomCore2. VS America

Basis of Design:Manufacturer: KISeries: My PlaceModel No: See Chart Below

Description: All seat and backrest frames are constructed of 3/4” laminated hardwoodplywood, CNC cut. All main frame joints are nailed and glued, in addition to interlocking joinery across all stress points. Seats are removable without tools for cleaning and electrical inspection.The seat base contains multiple pass-through cutouts to allow liquid and debris to route to the floor. Seats feature a curved clean-out space toroute liquid and debris towards floor.All My Place High-Back models use seat foam that is 2.5” thick, 2.5 density-45 lb. compression, topped with 1/2” thick, 2.6 density - 80 lb. compressionfoam. The backrest foam is 1-1/2” total thickness consisting of 1” thick, 2.5density - 45 lb. compression foam, and topped with a 1/2” thick, 2.6 density -80 lb. compression foam. All My Place Lounge units are double-needle stitchedat all primary seams for lasting durability. Concealed glides are height-adjustable steel, 1/4-20 threaded with a natural color nylon bottomallowing for 3/4” of leveling.

Base: Concealed GlidesWarranty: 15 Year



Model # Description Dimensions Room# QtyMPRCT/CLG/NC Rectangle 26"D x 48"W x 32"H 1009(3), 1021(1), 5

26"D x 48"W x 32"H 1022(1)





Fabric:Manufacturer: PallasPattern/Color: MOD/ChiliContent: 58% Polyester, 31% Post Consumer

Recycled Polyester, 11% NylonRepeat: 14-3/4" V, 14-1/2"HWidth: 54"Finish/Backing: Pinnacle/AcrylicWarranty: 3 YearFlammability: NFPA 260, TB 117-2013Abrasions: 105,000 Double RubsBase: Concealed Glides


Model # Description Dimensions Room# QtyMPRCT/CLG/NC Rectangle 26"D x 48"W x 32"H 1001(3), 6

1066A(3)

Fabric Back:Manufacturer: PallasPattern/Color: Aphrodite/Storm Cloud 27.258.112Content: NoneRepeat: 100% Poly Vinyl ChlorideWidth: 54"Finish/Backing: ResilienceWarranty: 3 YearsFlammability: 260TB 117-2013Abrasions: 250,000 Double RubsBase: Concealed Glides


Model # Description Dimensions Room# QtyMPRCT/CLG/NC Rectangle 26"D x 48"W x 32"H 1011(1),1016(1) 2



Fabric:Manufacturer: PallasPattern/Color: Holy Cow/Red Devil 27.144.208PRepeat: NoneContent: 100% PolyurethaneWidth: 54"Finish/Backing: Sta-KleenWarranty: 3 YearFlammability: NFPA 260,TB 117-2013Abrasions: 100,000 Double RubsBase: Concealed Glides


Model # Description Dimensions Room# QtyMPRCT/CLG/NC 26"D x 48"W x 32"H 2022(3), 2094(1) 16

2095(1),2111(2)2042(3),3020(3)3040(3)



2.3.4 SOFA

D1 Sofa



D1: Lounge Seating


Basis of Design:Manufacturer: KISeries: SolticeModel No: SLS/FC

Description: Frame Construction: Constructed of 5/4 lumber kiln dried to a moisture contentof six to eight percent and laminated hardwood plywood ¾” in thickness.All mainframe joints are double doweled and glued. Stress points are furtherreinforced with the use of glued and screwed corner blocks. . Suspension Seat:The seat platform is constructed with universal 7 ½ gauge sinuous wiresprings, firmly attached to front and back rails. Springs are installed on3 ½” c/c. A unitized spring surface is attained by attaching two (2) 16gauge insulated steel tie wires to each spring with Hartco clips running theentire length of the seat. A Flex-o-lator unit is then laid over the springs. Thesurface is then covered with a layer of FLS (reinforced non-woven fiber). Back:The back is sprung with stretch webbing stapled into position and covered witha layer of FLW. Arms: Arms are constructed of laminated hardwood plywood ½”and ¾” in thickness. Feet: The feet that attach to the arm are made of 8/4-beechhardwood, sanded then stained to client’s specification. Glide: A nylon glide isnailed into the bottom of each foot. Field Replaceable Backs, Arms, Seats Backsand arms are field replaceable and replacement parts come with newupholstery covers. The backs are attached to the arm frame with a metal-to-metal hinge connection that allows for easy replacement. Simply remove thetwo screws at the bottom of the back and lift the back up off the frame. Seatsare field replaceable and replacement parts come with new upholsterycovers. Foam Seats & Backs: Tight seats and backs are filled with a layer of 2”polyurethane foam with a density of 1.5 and a compression of 35 pounds. Thisfoam is covered with a layer of ¾” super-soft foam. Closed Arms: ¼”polyurethane foam is around the entire arm and has a 1.5 density and 45 pound compression Finish Exposed wood components are stained to customer specifications and are finished with catalyzed varnish.





Dimensions: 70.5"W x 30"D x 33"HWood Base: Natural on BeechWarranty: 15 Year

Fabric Back:Manufacturer: MomentumPattern: GlideColor: GraniteContent: 44% Polyester, 32% Pot Industrial Recycled Polyester, 24% Post Consumer

Recycled PolyesterWidth: 54"Finish/Backing: NoneWarranty: 3 yearFlammability: CA Bulletin 17 2013Abrasions: 102,000Repeat: 20-1/8"L, 19-3/8"W

Fabric Seat & Arms:Manufacturer: PallasPattern/Color: Bounce/Steel Gray 27.160.160Repeat: NoneContent: 100% PolyurethaneWidth: 54"Finish/Backing: Sta-KleenWarranty: 3 YearsFlammability: 260TB 117-2013Abrasions: 500,000 Double Rubs


Model # Room# QtySA843/FC 1099 2


Furniture, Furnishings and Equipment 120100-45D1-2

2.3.5 MODULAR FURNITURE

E1 Modular Lounge with Back E2 Modular Lounge Rectangular and Corner E3 Modular Curve with Back



E1: Modular Seating

1. FomCore2. VS America


Description: All seat and backrest frames are constructed of 3/4” laminated hardwoodplywood, CNC cut. All main frame joints are nailed and glued, in addition to interlocking joinery across all stress points. Seats are removable without tools for cleaning and electrical inspection.The seat base contains multiple pass-through cutouts to allow liquid and debris to route to the floor. Seats feature a curved clean-out space toroute liquid and debris towards floor.All My Place High-Back models use seat foam that is 2.5” thick, 2.5 density45 lb. compression, topped with 1/2” thick, 2.6 density - 80 lb. compressionfoam. The backrest foam is 1-1/2” total thickness consisting of 1” thick, 2.5density - 45 lb. compression foam, and topped with a 1/2” thick, 2.6 density -80 lb. compression foam. All My Place Lounge units are double-needle stitchedat all primary seams for lasting durability. Concealed glides are height-adjustable steel, 1/4-20 threaded with a natural color nylon bottomallowing for 3/4” of leveling.

Dimensions: 26"D x 48"W x 32"HBase: Concealed GlidesWarranty: 15 Year

Fabric Back:Manufacturer: KIPattern/Color: Point/Cobalt 27.203.094Content: 58% Post Consumer Recycled Polyester. 42% Post Industrial Recycled PolyesterWidth: 54"Finish/Backing: Greensheild AcrylicWarranty: 3 yearFlammability: NFPA-260 TB 117Abrasions: 60,000 Double RubsRepeat: 12-3/8"V. 7-1/8" H

Fabric Seat:Manufacturer: PallasPattern/Color: Bounce/True Blue 27.160.114Repeat: NoneContent: 100% PolyurethaneWidth: 54"Finish/Backing: Sta-KleenWarranty: 3 YearsFlammability: 260TB 117-2013Abrasions: 500,000 Double Rubs






Model # Room# QtyMPRB/CGL/FC 1091(4), 1093(4) 8Gangers Sets 2

Fabric Back:Manufacturer: KIPattern/Color: Nomad/Ground Breaker 27.307.098Content: 79% Post Consumer Recycled Polyester. 21% NylonWidth: 54"Finish/Backing: Alta/AcrylicWarranty: 3 yearFlammability: NFPA-260 TB 117Abrasions: 95,000 Double RubsRepeat: 10-1/4"V. 9" H

Fabric Seat:Manufacturer: PallasPattern/Color: Utopia/Cranberry 27.278.128Repeat: 13-1/2"V. 14" HContent: 39% Solution Dyed Nylon. 36% Rayon.25% PolyesterWidth: 54"Finish/Backing: Nanotex/AcrylicWarranty: 3 YearsFlammability: NFPA 260. TB 117-2013Abrasions: 100,000 Double Rubs


Model # Room# QtyMPRB/CGL/FC 2046(3), 2059(3), 3044(3), 3057(3) 18

E-Wing (3), J-Wing (3)MPCRN/CGL/FC 2046 (1), 2059(1), 3044(1), 3057(1) 6

E-Wing (1), J-Wing (1)Ganger Kits 10



E2: Modular Seating

Basis of Design:Manufacturer: KISeries:Model No:

Description:

Base:Warranty:




Fabric Back:Manufacturer:Pattern/Color:Content:Width:Finish/Backing:Warranty:Flammability:Abrasions:Repeat:

Fabric Seat:Manufacturer:Pattern/Color:Repeat:Content:Width:Finish/Backing:Warranty:Flammability:Abrasions:

2

12

Fabric Back:Manufacturer:Pattern/Color:Content:Repeat:Width:Finish/Backing:Warranty:Flammability:Abrasions:


222



Fabric Back:Manufacturer:Pattern/Color:Content:Repeat:Width:Finish/Backing:Warranty:Flammability:Abrasions:


1



E3: Lounge Seating

1. VS America2. Herman Miller

Basis of Design:Manufacturer: KISeries: My Place Model No: MPOCB/CGL/FC

Description: All seat and backrest frames are constructed of 3/4” laminated hardwoodplywood, CNC cut. All main frame joints are nailed and glued, in addition to interlocking joinery across all stress points. Seats are removable without tools for cleaning and electrical inspection.The seat base contains multiple pass-through cutouts to allow liquid and debris to route to the floor. Seats feature a curved clean-out space toroute liquid and debris towards floor.All My Place High-Back models use seat foam that is 2.5” thick, 2.5 density45 lb. compression, topped with 1/2” thick, 2.6 density - 80 lb. compressionfoam. The backrest foam is 1-1/2” total thickness consisting of 1” thick, 2.5density - 45 lb. compression foam, and topped with a 1/2” thick, 2.6 density -80 lb. compression foam. All My Place Lounge units are double-needle stitchedat all primary seams for lasting durability. Concealed glides are height-adjustable steel, 1/4-20 threaded with a natural color nylon bottomallowing for 3/4” of leveling.

Dimensions: 33-1/2D x 76-1/2"W x 32"HGlides: ConcealedWarranty: 15 Years






Fabric Back:Manufacturer: Arc-ComPattern/Color: Geostitch AC-62198Color: Smoke #9Content: 100% Post Industrial Recycled Solution Dyed NylonWidth: 54"Finish/Backing: Stain Resistant Finish/Acrylic BackingWarranty: 3 yearsFlammability:

Abrasions: 100,000 Double RubsRepeat: Approx. 7” H. x 5 3 4” V.

Fabric Seat:Manufacturer: PallasPattern/Color: Aphrodite/Storm Cloud 27.258.112Repeat: NoneContent: 100% Poly Vinyl ChlorideWidth: 54"Finish/Backing: ResilienceWarranty: 3 YearsFlammability: 260TB 117-2013Abrasions: 250,000 Double Rubs

Model # Description Room# QtyMPOCB/CGL/FC 90 Curve with back 1009 7MP Gang Kit 1009 10

1) ASTM E-84, NFPA 255, UL #723, UBC #8-1 Rated. UFAC Class 1/NFPA 260



2.3.6 TABLES

F1 Table F2 Multi-Purpose F3 Café Table F4 Teacher Table F5 Occasional Table F6 Accent Table F7 End Table F8 Side Table F9 Lounge Table F10 Benching Tables F11 Work Table F12 Large Rectangular Table F13 Executive Conference Table F14 Large Conference F15 Small Conference F16 Meeting Table F17 Meeting Table F18 Meeting Table F19 Conference Table F20 Work Bench F21 Work Bench



F1: Table


Basis of Design:Manufacturer: KISeries: C-TableModel No: CTABLE

Description: Tabletop Tabletops are 18” diameter and consist of 3 /4” thick high-density45 lb particleboard core with a .03” thick high-pressure laminate top and a .028” thick phenolic backer (bottom). The table edge is 2 mm polypropylene. Base Frame The table base frame is constructed of welded steel. The spider plate is 14-gauge, base is 3 /8” thick and the vertical post is 1-1 /2” diameterby .083” thick wall. The base frame is finished in electrostatically applied hybrid powder coating. The coating is then fused and cured in a baking oven to form a smooth, continuous finish that is chemical-resistant, hard, tough and mar-resistant. Powder-coated paint is available in all standard KI paintcolors except for chrome. Glides Six 1” diameter self-adhesive white polyurethane glides are recessed into machined pockets within the steelbase. Table Assembly Tabletops are attached to the base frame using seven#12 x 3 /4” Phillips truss head screws.

Dimensions: Top - 18" dia.Base - 15 1/2" dia.27" H

Top: LaminateTop Color: LFW Frosted WhiteTop Edge Color: EFW Frosted White

Base: C-Shaped BaseBase Color: SX Starlight Silver

Glides: 1" Dia. Polyurethane

Warranty: 15 Year

Room# Qty.1085(6), 2046(2), 2059(2), 3044(2), 3057(2) 18E-Wing(2), J-Wing(2)





F2: Mutli- Purpose Tables


Basis of Design:Manufacturer: KISeries: PirouetteDescription: Tabletops

Standard tabletops are nominal 1-1/4” overall thickness with .030” thick high-pressure laminate top surface and .028” phenolic backer (bottom surface). The density of the core in standard tops is 45 lb./cu ft. particle-board, M3 grade. Pirouette table is available with the 2 mm (74P) edge.Three T-Base leg depths are available. One depth fits 18” deep tables; one fits 24”and 30” deep tables; the other fits 36” deep tables. Leg height is fixed to provide 29"high tabletop height. An ADA table height of 32” is accomplished using 3" leg extensions threaded into the bottom of the leg. Café height of 36” and standing height of 42" are available. Leg construction consists of 2.2" diameter, .10" thickwall steel tubing with a 5 mm thick steel plate welded to it.The feet consist of two 4 mm thick blades welded to the leg tube. The bladecovers are aluminum die cast, attached with self taping metal screws. The leg assemblies are attached to the tabletops using #12 x 1" screws.

Base Color: SX Starlight SilverEdge: 74P*See Charts below for details






Pirouette Training TablePart # Glides Description Top/Edge Base Rm # Qty

PIFCRD60 Felt Rd, Fixed,60 D, 29"H LFW/EFW C-Base 1008(2) 2

1084(8), 2107 (6), 18 3105(4)

PIFCRD60 Nylon Rd, Fixed,60 Dia. 29"H LFW/EFW C-Base 1067(9) 9PIF3060T Felt Fixed 30"D x 60"W LFW/EFW T-Base 1024(3), 3

Table Ganger Set 1PIFXRD36 Felt 36" Round LFW/EFW X-Base 1127 1

PIF3060T Felt Fixed 30"D x 60"W LDG/ECG T-Base 1043 1

Room 2107 Chorus LabPart # Glides Description Top/Edge Grommet Wire Mgt. Qty

PAFR3060T Nylon Fixed,Training 30"Dx60" LDG/ECG L/R Trough 813.3115 Table Ganger (Set of 2) 2

Room 3105 Work-Based Learning LabPAFR3060T Nylon Fixed,Training 30"Dx60" LDG/ECG L/R Trough 13

13.3115 Table Ganger (Set of 2) 2

1047 Advanced RoboticsPart # Glides Description Top/Edge Grommet Wire Management Qty

PAFR3060T Felt Modified Fixed,30"x60" LDG/ECG Right Trough 4AC8JP.53 Active 8 Jumper 53"Long 2AC8IF.108.PI Active e 8 Infeed 2

1048 Robotics WorkshopPart # Glides Description Top/Edge Grommet Wire Management Qty


1050 Shared Work LabPart # Glides Description Top/Edge Grommet Wire Management Qty


w/ ganger kits

1051 Engineering Classroom 2Part # Glides Description Top/Edge Grommet Wire Management Qty

PAFR3060T Nylon Modified Fixed,30"x60" LDG/ECG Right Trough 16PAFR3060T Nylon Modified Fixed,30"x60" LDG/ECG Left Trough 16AC8JP.53 Active 8 Jumper 53"Long 16AC8IF.108.PI Active e 8 Infeed 16

w/ ganger kits

C-BaseLDG/ECGRd, Fixed,60 Dia. 29"HNylonPIFCRD60



1052 Engineering Classroom 1Glides Description Top/Edge Grommet Wire Management Qty

PAFR3060T Nylon Modified Fixed,30"x60" LDG/ECG Right Trough 16PAFR3060T Nylon Modified Fixed,30"x60" LDG/ECG Left Trough 16AC8JP.53 Active 8 Jumper 53"Long 16AC8IF.108.PI Active e 8 Infeed 16

w/ ganger kits

1064 FACS Interior DesignPart # Glides Description Top/Edge Grommet Wire Mgt. Qty

PIFR2460T Felt 24"x 60"Fixed Training LDG/ECG 5PI.Trough 44"Trough 5

13.3115 Table Ganger (Set 0f 2) 4PIFR3072T Felt Fixed Training 30" x 72" LDG/ECG 16

1085 Media CenterPart # Glides Description Top/Edge Grommet Wire Mgt. Qty

PIFR2430T Nylon Fixed Training 24" x 30" LDG/ECG 2PIFR2496C Nylon Fixed Training 24" x 96" LDG/ECG 4

3 Leg

1086 Maker SpacePart # Glides Description Top/Edge Grommet Wire Mgt. Qty

13.3115 Table Ganger (Set 0f 2) 2PIFR2496C Nylon Fixed Training 24" x 96" LDG/ECG 6

3 Leg

1087 Maker SpacePart # Glides Description Top/Edge Grommet Wire Mgt. Qty

13.3115 Table Ganger (Set 0f 2) 1PIFR2496C Nylon Fixed Training 24" x 96" LDG/ECG 4

3 Leg

1091 Special Education 2Part # Glides Description Top/Edge Grommet Wire Mgt. Qty

PAFR2448T Felt Fixed,Training 24"Dx48" LFW/EFW 213.3115 Table Ganger (Set of 2) 1

1093 Special Education 1Part # Glides Description Top/Edge Grommet Wire Mgt. Qty

PAFR2448T Felt Fixed,Training 24"Dx48" LFW/EFW 213.3115 Table Ganger (Set of 2) 1

2103 ROTCPart # Glides Description Top/Edge Grommet Wire Mgt. Qty

PAFR3060T Felt Fixed,Training 30"Dx60" LDG/ECG L/R Trough 513.3115 Table Ganger (Set of 2) 2

PAFR3072T Felt Fixed,Training 24"Dx72" LDG/ECG 1513.3115 Table Ganger (Set of 2) 5



2104 ROTCPart # Glides Description Top/Edge Grommet Wire Mgt. Qty

PAFR3060T Felt Fixed,Training 30"Dx60" LDG/ECG L/R Trough 513.3115 Table Ganger (Set of 2) 2

PAFR3072T Felt Fixed,Training 24"Dx72" LDG/ECG 1513.3115 Table Ganger (Set of 2) 5

3016 AV LabPart # Glides Description Top/Edge Grommet Wire Mgt. Qty

PAFR3072T Felt Fixed,Training 30"x72" LDG/ECG L/R Trough 16AC8JP.53 Jumper 53" Long 10AC8IF.108.PI Active e 8 Infeed 6

w/ ganger kits



F3: Tables


Basis of Design:Manufacturer: KISeries: Athens TableModel No: AH3R3642P-74PDescription: Fixed-Height Table Bases Tapered Base with 3" Diameter Column (ATH3) Tapered

round pedestal base is .07" thick steel. Tapered base is 22” diameter. 3" diametercolumn is constructed of 14-gauge steel. Table mounting plate is 7-gauge steel,and attaches to the underside of the work surface using eight #12 Phillips pan headscrews. Adjustable glides are 1" diameter, nickel plated with 5 /16" stems. No toolsare required for glide adjustment. Table mounting plate is 7-gauge steel, andattaches to the underside of the work surface using eight #12 Phillips pan head screws Base Finishes Standard base finishes include electroplated chrome and powdercoated oven-cured paint. Laminate Table Surfaces Laminate tops feature a 1-1 /8" thick high-density particleboard core with high-pressure laminate top and phenolic backing sheet. Total thickness of table top is 1-1 /4".

Dimensions:36" Dia. X 42"H

Top Color: (LFW) Frosty WhiteTop Edge Color: (EFW) Frosty WhiteBase Color: (SX) Starlight SilverGlides: NylonWarranty: 15 Years

Room # Qty1085 3






F4: Teacher Table


Basis of Design:Manufacturer: FleetwoodSeries: Unitized Frame - Plane Table

Description:

Glides: LevelersLaminate: Wilsonart-Florence Walnut 7993-38Edge Band: GraphiteBase: GraphiteWarranty: Limited Lifetime


Dimensions Room# Qty22"Dx48"w X30"H All Typical Classrooms 67(1 Each Room) 1050,1051,1052 18

2010,2017,2103,2104,2107,2108,3004,3009,3016,3087,3088,3097,3098,3104, 3105

Unitized Frame Table with Round Legs, 3/4" thick HPL Plane shape work surface, Adjustable height, Levelers





F5: Tables


Basis of Design:Manufacturer: KISeries: CalidaModel No: CAUVA2020Description: Table Top

Tables are offered in 3/4” thick high-density particleboard core withhigh pressure laminate top and phenolic backing sheet.Total thickness of top is 7/8”. Tops are available with a 2 mm (73P) edge.Table FramePlywood frame legs are made of 13/16” Birch plywood and are clear-coated or stained black. A steel plate connects to the table underside and is welded to curved metal wire, which is then inserted, glued andfastened to the plywood legs

Dimensions: 22"W x 13-1/2"HLaminate Top: LFW Frosty WhiteEdge Band Color: EFW Frosty White 73PBase: Wood Base Color: NaturalWarranty: 15 Year

Model # Room# QtyCAUVA2020 2046, 2059, 3044, 3057 12

E-Wing(2), J-Wing(2)





F6: Occassional Table


Basis of Design:Manufacturer: KISeries: Phoenix Model No: 21-1824ETDescription: High Pressure Laminate (HPL) tops are 3-ply balanced construction

and 1 5/32” thick with solid hardwood rims. Exposed surfaces areselect grade walnut and cherry veneers; Select grain patterns are used tomaintain consistency and proper balance between units. Veneers feature amulti-step catalyzed finish, allowing for grain clarity, resistance to normal wear and easy maintenance. Work surfaces are bonded to the core with a PVC adhesivein a cold press to prevent separation of the laminate orveneer from the core. Work surfaces are securely fastened togetherusing high quality European style fastening systems and heavy duty 16-gauge joining brackets and wooden dowels to assure maximum strength.

Dimensions: 18"W x 24"D x 30"HGlides: FeltLaminate Color: Artisen Walnut (AW)Glides: FeltWarranty: 12 Years

Room # Qty1137 1






F7: Occassional Table


Basis of Design:Manufacturer: KISeries: AffinaModel No: 9705

Description: All square and rectangular shaped bases have legs and aprons constructed of solidhardwood, kiln-dried to a moisture content of 6-8%. All bases are constructed usingdouble doweled and glued joints with glued and screw mounted corner blocks. TableTops Table tops are plastic laminate top surface, glued over solid wood. The edgeband is solid wood with a finish machined radius edge profile cut after thelaminate is applied.

Dimensions: 20"W x 24"D x 22"HGlides: FeltLaminate Color: CinnamonGlides: FeltWarranty: 15 Years

Room # Qty1121 1






F8: Lounge Seating


Basis of Design:Manufacturer: KISeries: Sway TableModel No: SYTB

Description: The Side Table top is 3 /4" thick, 45 lb. density built-up particalboard with a total thickness of 3". Overwrapping the sides andtop of the wood construction is .030" thick high pressure laminate.Table’s leg base is LLDPE rotationally molded, with a supportingstructure made of spun 12-gauge steel (finished thickness isapproximately .094 thick), powder-coat painted 90 gloss. TableTop Construction The Side Table top is 3 /4" thick, 45 lb. densitybuilt-up particle board with a total thickness of 3". Overwrappingthe sides and top of the wood construction is .030" thick highpressure laminate, available in all standard KI laminate colors.

Laminate: LRY River CherryEdge Band: ERY River CherryDimensions: 33" W x 32.5"D x 41.75"HShell: PCG Cool GreyBase: NylonWarranty: 15 Year

Dimensions Room # Qty27"Dia. x 32"H 1085 2





F9: Lounge Tables



Description: All seat frames are constructed of 3/4” laminated hardwoodplywood, CNC cut. All main frame joints are nailed and glued, in addition to interlocking joinery across all stress points. Frame bases are coated with a black stain and sealer to seal and protect wooden frames from liquidspills. All My Place Lounge units are double-needle stitched at allat all primary seams for lasting durability. Concealed glides are height-adjustable steel, 1/4-20 threaded with a natural color nylon bottomallowing for 3/4” of leveling.

Base: Concealed Glides

Warranty: 15 Year



Model # Dim. Laminate Top Edge Band Room# QtyMPT26R/CGL/NC 26" Dia. LSS Stainless ECG Cool Grey 1009 1





Fabric:Manufacturer: PallasPattern/Color: Nappa/Gotham 27.240.132Repeat: NoneContent: 100% PolyurethaneWidth: 54"Finish/Backing: Sta-KleenWarranty: 3 YearsFlammability: NFPA-260TB 117-2013Abrasions: 500,000 Double Rubs


Model # Dim. Laminate Top Edge Band Room# QtyMP18R/CGL/NC 18" Dia. SS Stainless Steel ECG Cool Grey 1009 2

Fabric Seat:Manufacturer: PallasPattern/Color: Burnish/Mirage 27.314.062Repeat: Mirage 27.314.062Content: 95% Polyurethane, 5% SiliconeWidth: 54"Finish/Backing: Writer's Block/100% PolyesterWarranty: 3 yearFlammability: NFPA 260, TB 117-2013Abrasions: 250,000 Double Rubs


Model # Dim. Laminate Top Edge Band Room# QtyMPTSQR/CGL/NC 26" Sq. LAZ Sterling Ash EAZ Sterling Ash 1085 6

MPTSQR/CGL/NC 26" Sq. LFC Florence EFC Florence 1006 6Walnut Walnut



Fabric:Manufacturer: PallasPattern/Color: Reflection/Flagstone 27.298.042Repeat: 20-3/4"V, 10-1/2" HContent: 100% PolyurethaneWidth: 54"Finish/Backing: Writer's BlockWarranty: 3 yearFlammability: NFPA 260, TB 117-2013Abrasions: 100,000 Double Rubs


Model # Dim. Laminate Top Edge Band Room# QtyMPTSQR/CGL/NC 26" Sq. LNA North Sea EGR Blue Grey 1099 2

Fabric:Manufacturer: PallasPattern/Color: Haven/Storm 27.291.132Repeat: NoneContent: 100% SiliconeWidth: 54"Finish/Backing: NoneWarranty: 5 yearFlammability: NFPA 260, TB 117-2013,ASTME-84Abrasions: 100,000 Double Rubs


Model # Dim. Laminate Top Edge Band Room# QtyMPT26R/CGL/NC 26" Dia. LDG Dove Grey ECG Cool Grey 1085 3



Fabric:Manufacturer: PallasPattern/Color: Nappa/Avocado 27.240.225Repeat: NoneContent: 100% PolyurethaneWidth: 54"Finish/Backing: Sta-KleenWarranty: 3 YearsFlammability: NFPA-260TB 117-2013Abrasions: 500,000 Double Rubs


Model # Dim. Laminate Top Edge Band Room# QtyMPTSQR/CGL/NC 26" Sq. LRY River Cherry LRY River Cherry 1091(2) 4

1093(2)

Fabric:Manufacturer: PallasPattern/Color: Haven/ Flame 27.291.268Repeat: NoneContent: 100% PolyurethaneWidth: 54"Finish/Backing: Sta-KleenWarranty: 3 YearsFlammability: NFPA-260TB 117-2013Abrasions: 500,000


Model # Dim. Room# QtyMP18R/CGL/NC 18" Dia. 1009 2



Fabric Seat:Manufacturer: PallasPattern/Color: Haven/Crimson 27.291.258Repeat: NoneContent: 100% SiliconeWidth: 54"Finish/Backing: NoneWarranty: 5 yearFlammability: NFPA 260, TB 117-2013,ASTME-84Abrasions: 100,000 Double Rubs


Model # Dim. Lam. Top Edge Band Room# QtyMPTSQR/CGL/NC 26" Square LDG Dove Grey ECG Cool Grey 1127 2



F10: Tables In compliance with the intent and requirements of these Bidding Documents, provide the Basis-of-Design Product described below.



Basis of Design:Manufacturer: KISeries: Connection Zone

* See ChartsWWork surfaces: Work surfaces are constructed of 11 /8” thick, 45-pound density particleboard core. Adheredon the top is a .030” face sheet of high-pressure laminate and on the bottom with a .030”phenolic backer. Total work surface thickness is 11 /4” thick. Edges are evenly adhered tothe work surface. All work surfaces are pre-drilled for support brackets and support legs.Work surfaces are offered in rectangular and extended corner shapes to support multipleconfigurations. Work surface overhang will vary by configuration and screen use. 74P anKnife edge styles are available and optional rectilinear shaped grommets may be specifiedfor most work surfaces. SSteel Leg Frames: Frames are constructed of steel with a modular understructure consisting of end legs connectedby a transverse telescoping center support beam. Longer runs can be achieved by adding intermediate legs and additional support beams as needed. Frame leg is a fixed height “goalpost”style with a cross section of 19 /16” x 23 /8”. Glides offer 7 /8” of height adjustment. Frames areoffered in a variety of colors with a powder-coat finish. 229” Steel Leg - Standard Table Height: Dual-sided frames are offered in 48” or 60” depths and support either fixed or sliding work surfacesin 24” and 30” depths.

FFrameless Privacy Screens: Frameless privacy screens, which are designed to span the frame spacing. Material insert options include translucent or colored acrylic, and clear or satin etched temper safety glass. Frameless privacy screens are available from 36” through 96” widths in 6” increments by 13”or 19” heights. EElectrical – 810: The US standard electrical system available on Connection Zone Benching is an 810 electrical system (20 amps per circuit). Rigid wire way harnesses are mounted to the underside of work surfaces on steel leg single-sided applications. On steel and wood leg dual-sided applications, the wire way is located between work surfaces and supported by a formed 14-gauge steel channel supported on each end by the frame supports. Power is supplied through a 6-2-2 configuration with six hot wires, two shared oversized neutral wires and two ground wires(one isolated ground and one building ground). Rigid wire ways pass power to 15-ampreceptacles. The 810 electrical system is UL Listed per the UL 183 standard. AActiv8® Electrical: The Activ8 electrical system is a UL 962 recognized component that allows up to eight duplex power modules to be connected to one standard 15-amp power cord. Activ8 electrical system does not require modules to be connected in a certain order. The number of power modules connected is automatically limited to the maximum allowed under UL standard 962. If too many modules are connected, the Activ8 control box disconnects all power to the systemand illuminates a red LED. Power is resumed automatically to the system once the extra power module or modules are disconnected, which is indicated by a green LED. The fuse on the powercontrol box can be reset as it is used to limit the number of devices on the chain. If the systemreceives a voltage spike, it would likely destroy the box and would need to be replaced. BBase Infeed: The UL 183 electrical system permits power infeed in either of two locations. Power may be



brought in at any intermediate leg location, or it may enter at the end of any run, directly into the end of the cable trough. Optional metal panels are available to shroud the infeed in the intermediate leg location (dual-sided applications only). AActiv8® Power Infeed: Series includes a standard NEMA 5-15P 15-amp plug on one end of the 108” cord and a non-sequentially keyed connector at the opposite end of the cord. Control box is located 12" from the table connection. Built-in diagnostics LED shows system status: EElectrical - Center Work Rail: The center rail-supported electrical is necessary for dual-sided applications when supportingprivacy screens or frameless privacy screens are specified. The rigid wire ways (which are identical to the 810/6-2-2 components) are attached to the bottom aluminum rail on site. Infeeds, jumpersand receptacles are specified the same as with the standard electrical. TTable-to-Table Jumpers: 18” jumpers feature flexible metal conduit. AActiv8® Jumpers: Each jumper is equipped with a connector on each of two ends that plug into any connector on a given power module. Jumpers are non-sequential and are interchangeable to the extent that the jumper length is sufficient to reach the next module. Jumpers are available in four standard lengths of 29”, 53”, 77” and 101”

RReceptacles: 15-amp receptacles for the modular electrical system feature injection molded Components which snap fit into the rigid wire ways.

RRPT Module for Activ8® with RPT Bracket: Includes two AC outlets per module. A connector with three ports is located at the opposite end of the 12” cord. CCable Management: Dual-sided applications: The cable tray is secured with a variable support bracket onto the understructure of the beam rails. The cable tray is evenly shared between the work surfaces and is accessible from the top when specified with sliding work surfaces. The cable tray is accessible from the underside of the structure when specified with fixed work surfaces. CCompliance: Connection Zone Benching is a UL Listed Office Furnishing per standard UL 1286 and PoweredFurniture per standard UL 962.



F11: Work Tables


Basis of Design:Manufacturer: KISeries: PorticoModel No: See Chart Below

Description: Portico®® Pedestal Base Table This system employs 14-gauge, 1 3/4" O.D. tubular 1010 steel columns in fixedmodels. Foot tube is 16-gauge, 1 3/4" x 7/8" elliptical steel. Portico includes T, TT, LX and cantilevered ‘T’ base combinations. LX series is furnished with 3"O.D. seamless tubular steel column. Plastic end caps are secured via a "force fit". The column cap is secured via a screw. Column-to-foot tube joints will be silverBrazed with 505 alloy (50% silver and 50% other, including 2% nickel added fora strong joint). Adjustable glides are secured to the legs via steel inserts in foottube (riv-nuts) which provide a 5/16" threaded hole for the glide. Fixed table column welded to an 8" x 8" square, 12-gauge sheet steel plate withFormed ribs for added strength and 4 mounting screws (5/16" hole for a #14 screw). LX base will be welded to an 8" x 8", 1/4" sheet steel plate.

Tops consist of a 11/8" thick high-density particleboard core with a .020"

high-pressure laminate top and .020" phenolic backing sheet. Tops are pre-drilled. Vinyl "T" molding will be press fit into particle board core. KI tables canhold a maximum of 1.5 lbs for each inch of perimeter evenly distributed over the top.

Leg: FixedEdge: 2mm PVC (54B)Base Color: SX Starlight SilverWarranty: 15 Year

Note: Image is for reference only; see above specification for exact model information.Model # Dimensions Laminate Top Edge Band Base Room# QtyPFIX 30"x66"x29" LFW Frosty White EFW Frosty White Fixed T 1092 1PFIX 36"x84 x 29" LFW Frosty White EFW Frosty White Fixed T 1091(2), 4

1093(2)PR35FX 42" Round LFW Frosty White ESP Surf's Up Fixed X 1091,1093 2PR35FX 42" Round LFW Frosty White EGN Grass Green Fixed X 1091,1093 2PR35FX 42" Round LFW Frosty White ESK Sky Blue Fixed X 1091,1093 2PR35FX 42" Round LDG Dove Grey ECG Cool Grey Fixed X 1099 5





F12: Table


Basis of Design:Manufacturer: KISeries: PillarModel No: PLRT3696

Description: Standard Tabletops: Standard tabletops are nominal 1-1 /4” overall thickness with.030” thick high-pressure laminate top surface and .028” phenolic backer (bottomsurface). The density of the core in standard tops is 45 lb/cu ft particleboard, M3grade. The Pillar Table is available with the 2 mm (74P) edge.The leg construction consist of a 2-1 /4” O.D., 14-gauge steel tubing welded to a 1 /4”thick 8” x 8” steel plate. A 1/4” thick steel insert is welded in the bottom of each legtube with a 1/2-13 UNC threaded hole where the casters or glides attach. The legs areattached to the tabletop using #12 x 1” screws. Casters and glides are shipped inseparate cartons and must to be installed upon assembly of the table. Glides are black nylon, overmolded on a steel insert for strength. Glides and castersare not interchangeable without changing the table height. Caster wheels are a minimum of 27 /16” (63 mm) diameter. Glides have a smooth bottom surface forGlides have a height adjustment range of 1" to allow for uneven surfaces.

Dimensions: 36"D x 96"W x 29"HTop Color: LRY River CherryTop Edge Color: ERY River CherryBase Color: SX Starlight SilverGlides: NylonWarranty: 15 Year

Dimensions Top Edge Room# Qty36" x 96" 29" LDG Dove Grey ECG Cool Grey 2106 230"x 72" x 36" LDG Dove Grey ECG Cool Grey 1064 236"D x 108"Wx 37.31H LDG Dove Grey ECG Cool Grey 1064 136"D x 142"W x 37.31"H LDG Dove Grey ECG Cool Grey 1023 148"D x192"W x 37.31"H LDG Dove Grey ECG Cool Grey 1024 1





F13: Executive Conference Table

1. Steelcase2. Herman Miller

Basis of Design:Manufacturer: IndianaSeries: PhoenixModel No: See Chart Below

Description: Veneer tops are 1 5/32” thick with a 5-ply balanced construction and feature a solid hardwood rim. High Pressure Laminate (HPL) tops are 3-ply balanced construction and 1 5/32” thick with solid hardwood rims. Exposed surfaces are select grade walnut and cherry veneers; Select grain patterns are used tomaintain consistency and proper balance between units. Veneers feature amulti-step catalyzed finish, allowing for grain clarity, resistance to normal wear and easy maintenance. Work surfaces are bonded to the core with PVC adhesive in a cold press to prevent separation of the laminate orveneer from the core. Work surfaces are securely fastened together usinghigh quality European style fastening systems and heavy duty 16-gauge joining brackets and wooden dowels to assure maximum strength.

Wood: Artisan Walnut (AW)Edge: G-DuoWarranty: 12 Year


Model # Description Dimension Room# Qty92-48168RT Veneer Conference Table 168"W x 48"D x 29"H 1141 101-1222CS Canoe Base 22" x 12" X 28-1/2" 1141 3





F14: Conference Table


Basis of Design:Manufacturer: IndianaSeries: CanvasModel No: See Chart Below

Description: Work surface ConstructionLaminate tops are 1-3/16” thick and feature 3-ply balanced construction and PVCrims. Conference tops are shaped on all four sides for complete design appeal. Exposed surfaces are produced from wood grained and solid color laminatesfused to a particle-board core. Table Tops are bonded to the core with a PVA adhesive in a cold press to prevent separation of the laminate from the core. Basesare constructed with a Grade M2 particleboard core with Veneer on exposed facesand a black sheet backer on all unexposed faces. Bases offered with and withoutdoors/removable panels.

Dimensions: See Chart BelowLaminate: Columbian Walnut (CO)Warranty: 12 Year


Model # Description Dimension Edge Room# Qty94-48168RT HPL Conference Table 168"W x 48"D x 29"H G-Duo 1098 101-1222TS 01-1222TS Bow Tie Base 22" x 12" X 28-1/2" 1098 3





F15: Small Conference Table


Basis of Design:Manufacturer: IndianaSeries: Canvas

Model No: See Chart Below

Description: Work surface ConstructionLaminate tops are 1 3/16” thick and feature 3-ply balanced construction and PVC.rims, Conference Tops are shaped on all four sides for complete design appeal. Exposed surfaces are produced from wood grained and solid color laminatesfused to a particle-board core. Table Tops are bonded to the core with a PVA adhesive in a cold press to prevent separation of the laminate from the core. Bases are constructed with a Grade M2 particleboard core with Veneer on exposed faces and a black sheet backer on all unexposed faces. Bases offered with and withoutdoors/removable panels. Cylinder bases are weighted for stability.

Dimensions: See Chart BelowTop: Shaker Cherry-SKCPEdge: Square EdgeWarranty: 12 Year


Model # Description Dimension Edge Room Qty94-4296RT Conference Tble 96"W x 36"D x 29"H Y-Square 1140 101-2020CB Cylinder Base 20"D x 28-1/2"H 1140 3







Basis of Design:Manufacturer: Indiana

Series: CanvasModel No: See Chart Below

Description: Work surface ConstructionLaminate tops are 1 3/16” thick and feature 3-ply balanced construction and PVC.rims, Conference Tops are shaped on all four sides for complete design appeal. Data and wire management is available. options. Exposed surfaces are produced from wood grained and solid color laminatesfused to a particle-board core. Table Tops are bonded to the core with a PVA adhesivein a cold press to prevent separation of the laminate from the core. Bases areconstructed with a Grade M2 particleboard core with Veneer on exposed faces anda black sheet backer on all unexposed faces. Bases offered with and withoutdoors/removable panels.Cylinder Bases are weighted for stability.

Top: Shaker Cherry-SKCPEdge: Square EdgeWarranty: 12 Year


Model # Description Dimension Edge Room Qty86-3672MT TFL Meeting Table 72"W x 36"D x 29"H Y-Square 1118 108-2828YGL2 Y-Base 08-2828YLG2 1118 2





F17: Round Meeting Table


Basis of Design:Manufacturer: IndianaSeries: PhoenixModel No: See Chart Below

Description: Veneer tops are 1 5/32” thick with a 5-ply balanced construction and feature a solid hardwood rim. High Pressure Laminate (HPL) tops are 3-ply balanced construction and 1 5/32” thick with solid hardwood rims. Exposed surfaces are select grade walnut and cherry veneers; Select grain patterns are used tomaintain consistency and proper balance between units. Veneers feature amulti-step catalyzed finish, allowing for grain clarity, resistance to normal wear and easy maintenance. Work surfaces are bonded to the core with PVC adhesive in a cold press to prevent separation of the laminate orveneer from the core. Work surfaces are securely fastened together usinghigh quality European style fastening systems and heavy duty 16-gauge joining brackets and wooden dowels to assure maximum strength.

Wood: Artisan Walnut (AW)Edge: G-DuoWarranty: 12 Year


Model # Description Dimension Room QtySP21-6060CT Veneer Conference Table 168"W x 48"D x 29"H 1137 1SP21-6060CT Cylinder Base 1137 1





F18: Round Meeting Meeting Table



Description: Work surface ConstructionLaminate tops are 1 3/16” thick and feature 3-ply balanced construction and PVC.rims, Conference Tops are shaped on all four sides for complete design appeal. Data and wire management is available. options. Exposed surfaces are produced from wood grained and solid color laminatesfused to a particle-board core. Table Tops are bonded to the core with a PVA adhesivein a cold press to prevent separation of the laminate from the core. Bases areconstructed with a Grade M2 particleboard core with Veneer on exposed faces anda black sheet backer on all unexposed faces. Bases offered with and withoutdoors/removable panels.Cylinder Bases are weighted for stability.

Top: Shaker Cherry-SKCPEdge: Square EdgeWarranty: 12 Year


Model # Description Dimension Room Qty66-3636CT TFL Meeting Table 48" Diameter 1136(1), 2086(1),3083(1) 308-2030SXB 30" X-Base 1136(1), 2086(1),3083(1) 3







Basis of Design:Manufacturer: KISeries: Connection Zone ConferenceModel No: CZBTCR3696-74P

Description: Rectangular Conference Table Table Worksurfaces are constructed of 1-1 /8” thick, 45-pound density particleboard core. Adhered on the top is a .030” face sheet of high-pressure laminate and on the bottomwith a .030” phenolic backer. Total worksurface thickness is 11 /4” thick. Edges are evenly adhered to the worksurface. All worksurfaces are pre-drilled for supportbrackets and support legs. Worksurfaces are offered in rectangular and extended corner shapes to support multiple configurations. Worksurface overhang will vary byconfiguration and screen use. 74P and Knife edge styles are available and optional rectilinear shaped grommets may be specified for most worksurfaces. Knife edge useis restricted to the edge facing the occupant.Wood Leg Frames Two hardwood end legs bolt to a steel apron which connects to amodular understructure, consisting of a modular transverse telescoping centersupport beam that connects to the next end wood leg frame apron. Longer dual-sidedruns can be achieved by adding intermediate legs and additional support beams asneeded. Frame leg is a fixed height 13 /16” thick solid tapered hardwood upright.Glides offer 7 /8” of height adjustment. Frames are offered in a variety of powder-coatfinishes for the understructure, and various stains for the wood component.

Dimensions: 36" x 96" Laminate Top: LFW Frosty WhiteEdge Band Color: EFW Frosty White 74PMetal Frame: Powder Coat (SX) Starlight SilverBase: Wood Base Color: NaturalWarranty: 15 Year

Room# Qty2046(2),2059(2), 3044(2), 123057(2),E-Wing(2), J-Wing(2)





F20: Work Bench

1. Hann2. Uline

Basis of Design:Manufacturer: Diversified WoodcraftModel:

Description: Four-Station WorkbenchThe top is 2-1/4" butcher block solid maple with 4-leg steel base.Frame material is solid maple with maple veneers and a UV finish.

Dimensions: 36"W x 72"L x 32"HTable Top: 2-1/4" Maple Top SolidFrame: SteelCapacity: 600lbsWarranty: Lifetime Limited


Dimensions Qty36"W x 72"L x 32"H 16



1052(2)1047(3), 1048(3), 1051(2)1041(2), 1042(2), 1043(2)

Room#



F21: Work Bench

1. Hann2. Uline

Basis of Design:Manufacturer: Diversified WoodcraftModel:

Description: Four-Station WorkbenchThe top is 2-1/4" butcher block solid maple with storage below.Frame material is solid maple with maple veneers and a UV finish.

Dimensions: 64"W x 54"L x 32"HTable Top: 2-1/4" Maple Top SolidFrame: SteelCapacity: 600lbsWarranty: Lifetime Limited


Room# Qty1042(6), 1050(6) 12



64"W x 54"L x 32"HDimensions



2.3.7 LECTERN

G1 Lectern



G1: Lectern

Basis-of-Design: Manufacturer: KISeries: Ruckus Mobile LecternModel No: RUX20

Description: Single post cantilever pneumatic cylinder base with locking feature. High-density 45 lb. particleboard core contoured top. Modesty paneland cup holder.Lower base 14 ga., 2" x 1- 1/4" steel tubing, Upper column 3" dia. aluminum extrusion.

Dimensions: 30" W x 20" D Adjustable height 28 3/4" - 42 3/4"

Top: 13/16" thick, .03 thick laminate surface, 73P polypropylene edgeTop Color: LIT Italian Silver AshEdge Band: EIT Italian Silver AshModesty Panel: 20" x 20" x 1/4" Acrylite SatinicePanel Color: ACSCup Holder Color SX Starlight SilverBase Color: SX Starlight Silver

Warranty: 15 Year

Room# Casters Qty1st Floor1064,1091,1093, Soft 31051,1052 Hard 2

2nd Floor Typical Classroom Hard 342009, 2103, 2104,2106, 2107, 2108 Hard 62010,2017 Soft 2

3rd Floor Typical Classroom Hard 333009,3016, 3087, 3088,3097,3098,3104 Hard 7



1. Herman Miller



2.3.8 DESK

H1 Student Desk H2 Teacher Desk H3 Administration Desk H4 Executive Desk H5 Work Station



H1 Student Desk

Basis of DesignManufacturer: KISeries:Model No:Description:

Dimensions:Molded Top:Base:

Glides:Warranty:



H2 Teacher Desk


Basis of Design:Manufacturer: FleetwoodSeries: Tables & Desks - Conventional DeskDescription:

surfaces and edges are finished and sealed with glue bonds to create

16-gauge steel tube with levelers welded to metal frame.

Laminate: Wilsonart-Florence Walnut 7993-38Edge Band: GraphiteBase: GraphiteWarranty: Limited LifetimeGlides 1-7/8" Black


Model No. Dimensions Description Room# Qty1019002-297710 26"D x 66"W x 30"H Double Pedestal All Typical Classrooms 67

1050, 1051, 1052, 2010 182017, 2103, 2104, 2107,2108, 3004, 3009, 3016,3087, 3088, 3097, 3098,3104,3105

1018004-29771 26"D x 66"W x 30"H Single Pedestal 1049(2), 1057, 1059, 1064A, 231079(2), 2008, 2011, 2016,2080, 2090, 2091, 2092,3007(2), 3008(2), 3010,3089, 3092, 3093, 3096



adhesive and trimmed flush on top and bottom to create a pry proof edge.Rounded corners have 2” radius on corners. 24" deep top has 11-7/8"radius. 30” deep top has 14-7/8” radius. Legs feature 2.75” tall 1-1/4” diameter

Particleboard work surfaces have steel understructures. All particleboard

moisture barrier. Permanently attached 3mm color-matched or coordinatingPVC edge band with ergonomic 1/8” radius top edge bonded with hot-melt



H3: Administration Desk



Description: Work surfaces are 1" thick thermally-fused laminate (TFL) or high pressure laminate (HPL) using 3mmmatching PVC rims on profiled edges and 1 mm matching PVC rims on self edges. Work surfaces and tops oncase goods less than 65”H are constructed with a Grade M2 particleboard core 45 lb. medium density fiber-board core with thermally-fused laminate (TFL) or high pressure laminate (HPL) on exposed face and a blackbacker sheet on all unexposed faces. Tops on case goods greater that 65"H are constructed with Grade M2particleboard core 45lb. medium density fiberboard core with thermally fused laminate on both faces.Work surfaces are bonded to the core with a PVA adhesive in a cold press to prevent separation of thelaminate form the core. Work surfaces are securely fastened together using high quality Europeanstyle fastening systems and heavy-duty 16-gauge joining brackets and wooden dowels to assure maximum strength. Primary work surfaces are profiled on approach and user sides; Secondarywork surfaces are profiled on user side only. Work surfaces must fit flush with adjoining work surfaces. TFL chassis and storage components are securely fastened together using high quality Europeanstyle fastening systems and heavy-duty 16-gauge joining brackets and wooden dowels to assure maximum strength. Case good components are constructed with a Grade M2 particleboard core withthermally fused laminate on both faces. All units feature leveling glides with 1-1/4" of adjustment.Exposed edges have matching PVC edge band. Back panels on all units are inset into the sides so noraw edges are visible. All desks, non-lateral credenzas, and returns have wire management access frompedestal to knee space. Modesty panels are available on returns. L-support panels offer support for work surfaces without modesty panels. Hinges on all doors are soft close, concealed and open 100 degrees.The height from the work surface to the bottom of a surface mounted hutch is 23-3/4".Lateral File cabinets are equipped with an anti-tilt system which only allows one drawer to open at atime. Lateral file and hybrid storage cabinets are standard with central locking. Only one lock isrequired to lock all drawers. Door will have a separate lock that will match the drawers. Drawer andDoor fronts have vertically matched grain and utilize the same drawer construction as the pedestals. All desks, credenzas, returns, and files feature standard removable lock cores for re-keyingin the field.

Top: Bow FrontPulls: 5" Arc Aluminum (AAC)Edge: Duo (G)Drawer Grain: VerticalWarranty: 12 Year






Mod

el #

Des

crip

tion

Dim

ensi

onLa

min

ate

Room

#Q

ty68

-367

2BLS

PSt

eppe

d Fr

ont B

ow T

op36

"D x

72"

W x

29"

HSh

aker

Che

rry-

SKC

P10

75,2

027,

206

4, 2

079,

9

Sing

le L

eft P

edes

tal D

esk,

B/B

/F20

86,3

024,

306

2, 3

078,

3083

66-2

472R

MF

Righ

t Mul

ti Fi

le C

rede

nza

24"D

x72

"W x

29"

HSh

aker

Che

rry-

SKC

P10

75, 2

027,

206

4, 2

079,

7

3024

,306

2, 3

078,

68

-367

2BRP

SSt

eppe

d Fr

ont B

ow T

op-S

ingl

e36

"D x

72"

W x

29"

HSh

aker

Che

rry-

SKC

P11

36, 3

079

2Ri

ght P

edes

tal D

esk,

B/B

/F68

-247

2LM

FLe

ft M

ulti

File

Cre

denz

a24

"D x

72"W

x 2

9"H

Shak

er C

herr

y-SK

CP

1136

, 307

92

66-2

448U

FHEx

. Brid

ge-H

alf M

odes

ty P

anel

24"D

x48

"W

Shak

er C

herr

y-SK

CP

1075

, 113

2,11

35, 1

136,

2027

, 13

2064

, 207

9, 2

086,

3024

,306

2, 3

078,

307

9,30

83,

66-1

572H

USu

rface

Mou

nt D

oor

Hut

ch72

"W x

40-

7/8"

HSh

aker

Che

rry-

SKC

P10

75, 2

027,

206

4,20

798

3024

, 306

2, 3

078,

3079

TB-6

672

Surfa

ce M

t Hut

ch T

ack

boar

d72

"10

75,2

027,

206

4,10

2079

,208

6,30

24,

3062

,307

8, 3

079,

3083

,66

-246

6RM

FRi

ght M

ulti-

File

Cre

denz

a24

"D x

66"

WSh

aker

Che

rry-

SKC

P11

32,1

135,

2

66-2

436L

2Tw

o D

raw

er L

ater

al F

ile24

"D x

36"

WSh

aker

Che

rry-

SKC

P11

352

66-2

436M

FM

ulti-

File

24

"D x

36"

W11

14, 1

115,

266

-153

6TU

Top

Uni

t Boo

kcas

e36

"W x

42"

HSh

aker

Che

rry-

SKC

P11

14, 1

115,

113

54

68-3

066L

PLe

ft Pe

d D

esk

30"D

x 6

6"W

Shak

er C

herr

y-SK

CP

1114

,111

7,11

19,1

120,

911

22,1

124,

1126

,113

2,11

3568

-246

6SC

Stor

age

Cre

denz

a24

"D x

66"

WSh

aker

Che

rry-

SKC

P11

16,1

117,

1119

,112

0,11

22,

911

23,1

124,

1125

,112

668

-247

2SC

Stor

age

Cre

denz

a24

" D x

72"

WSh

aker

Che

rry-

SKC

P20

86, 3

083

266

-156

6OH

Surfa

ce M

ount

Hut

ch15

"D x

66"

WSh

aker

Che

rry-

SKC

P11

16,1

117,

1119

,112

0,11

22,

911

23,1

124,

1125

,112

6

08-2

030S

XBSm

all X

Bas

e 30

" Circ

leAl

umin

um11

16,1

117,

1119

,112

0,11

22,

911

23,1

124,

1125

,112

666

-363

6CT

Circ

ular

Top

36"

Dia

.Sh

aker

Che

rry-

SKC

P11

16,1

117,

1119

, 112

0,11

229

1123

,112

4,11

25,1

126

68-2

448L

F2Le

ft Pe

d. R

etur

n F/

F24

"D x

48"

WSh

aker

Che

rry-

SKC

P11

15,1

116,

1123

,112

54

68-3

066R

PRi

ght P

ed. D

esk

30"D

x 6

6"W

Shak

er C

herr

y-SK

CP

1115

,111

6,11

23,1

125

468

-244

8RF2

Righ

t Ped

. Ret

urn

F/F

24"D

x 4

8"W

Shak

er C

herr

y-SK

CP

1114

,111

7,11

19,1

120,

911

22,1

124,

1126

, 208

6,30

8366

-157

2OH

Surfa

ce M

ount

Hut

ch15

" x 7

2"Sh

aker

Che

rry-

SKC

P20

86,3

083

2



Mod

el #

Des

crip

tion

Dim

ensi

onLa

min

ate

Room

#Q

ty01

-000

60SB

Stiff

ener

Bar

for O

pen

1110

2Kn

ee s

pace

60"

or

Larg

er66

-101

0SPW

T

Supp

ort w

ith W

ire M

gt

1110

266

-233

0EP

Mod

ular

End

Pan

el,

23-1

/4"W

x1"D

x28-

1/4"

H

Shak

er C

herr

y-SK

CP

1110

166

-152

8BP

Mod

ular

Bac

k Pa

nel,

15W

x 2

8-1/

4H x

3/4

DSh

aker

Che

rry-

SKC

P11

101

66-2

415P

D1

Mod

ular

Ped

esta

l, B/

B/F

15-3

/4W

x23-

1/4D

x28-

1/4H

Sh

aker

Che

rry-

SKC

P11

102

66-2

484T

PM

odul

ar L

am. C

abin

et T

op24

" D x

84"

WSh

aker

Che

rry-

SKC

P11

101

66-2

496T

PM

odul

ar L

am. C

abin

et T

op24

"D x

96"

WSh

aker

Che

rry-

SKC

P11

101



Room

#11

10Ro

om #

1114

Room

#11

15

Room

#11

16Ro

oms

#11

17, 1

119,

112

0,

Room

# 1

122,



Room

s #

1123

, 112

5,

Room

s #

1124

, 112

6,

Room

#11

32Ro

om #

1135

Room

#11

36



Room

s #

2086

& #

3083

Room

#30

79Ro

oms

#10

75, 2

027,

206

4, 2

079,

3024

, 306

2, 3

078



H4: Executive Desk & Storage


Basis of Design:Manufacturer: IndianaSeries: PhoenixModel No: See Chart BelowDescription: Custom desk and storage unit.

Veneer tops are 1 5/32” thick with a 5-ply balanced construction and feature a solid hardwood rim. High Pressure Laminate (HPL) tops are 3-ply balanced construction and 1 5/32” thick with solid hardwood rims. Exposed surfaces are select grade walnut and cherry veneers; Select grain patterns are used tomaintain consistency and proper balance between units. Veneers feature amulti-step catalyzed finish, allowing for grain clarity, resistance to normal wearand easy maintenance. Desk work surfaces are shaped on all four sides. Worksurfaces are bonded to the core with a PVC adhesive in a cold pressto prevent separation of the laminate or veneer from the core. Work surfaces are securely fastened together using high quality European style fastening systems and heavy duty 16-gauge joining brackets and wooden dowels to assure maximum strength. Drawer fronts are standard with matched veneerfaces. Drawer sides, back and fronts are 1/2" woodgrain vinyl-wrapped.Box and file drawers have 1/8" thick hardboard bottoms. Lateral file drawers1/4” thick bottoms. Box and file drawers are tested for 100lb capacity; Lateral files are tested for 200lb capacity. All drawers have full extension,progressive action slides with precision steel ball bearings. All suspension have a lifetime warranty. File drawers have full height sides and metal file rails.

Dimensions: See ChartWood Veneer: Artisen WalnutPulls: Quadra Aluminium - 4"Glides: Felt / Nylon - See list belowWarranty: 12 Year

Tack Board Fabric: Grade 3 Color: To be selected by designer.





H4S

Execu

tive

Sp

rea

dsh

eet

Pri

nci

pa

l's O

ffic

eM

odel

#D

escr

iptio

n D

imen

sion

Room

#Q

ty01

-000

60SB

Stiff

ener

Bar

1137

2TL

-084

8Ta

sk L

ight

48"

1137

1SP

21-6

626B

PC

usto

m D

esk

Back

Pan

el62

-"W

x3/

4"D

x 2

6-1/

4H11

371

with

L-B

rack

ets

SP57

-243

0EP2

FBN

Mod

ular

End

Pan

el23

- 3/

16" x

1" x

28-

1/4"

1137

1S0

1-30

30C

B30

" Dia

. Cyl

inde

r Ba

se fo

r 60

" Top

1137

1SP

21-3

017P

D1

Cus

tom

Mod

ular

BBF

ped

for

use

with

1137

1lo

ckin

g m

odul

ar to

p an

d ba

ck p

anel

SP21

-243

6DB-

FRD

oubl

e D

oor

Cab

inet

& w

ood

top

24D

x 3

6D11

371

TB-2

170W

Hut

ch T

ack

Boar

d70

"11

371

SP21

-368

4TPL

Cus

tom

Ret

urn

Top,

Rig

ht R

ever

se p

rofil

e36

"D x

84"

W11

37SP

21-6

060C

T60

" Dia

. Tab

le T

op-P

hoen

ix E

dge,

Woo

d60

" D11

371

21-1

636T

UTo

p U

nit B

ookc

ase/

FR16

"D X

36"

W11

371

21-1

636T

UTo

p U

nit B

ookc

ase/

FL16

"D X

36"

W11

371

32-1

670W

DW

all M

ount

Hut

ch16

"D x

70"

W11

371

S21-

2410

6RM

FM

ulti-

File

Cre

denz

a24

" x10

5-3/

4" R

ight

/MF

1137

1



2.3.9 STORAGE

I1 Storage Cabinet with Cubbies I2 Storage Cabinet with Doors I3 Bookcase I4 Executive Bookcase I5 Storage Cubbies I6 Cash Register Unit with Storage I7 4-Sided Display I8 Metal Shelves I9 Metal Lockers



I1: Storage with Cubbies

Basis of Design:Manufacturer: KISeries:Model No:Description:



Double SidedUnits:Overhang:Table Height:Glides:Warranty:

Paint Color:Edge Color:Shelf Color:

2

2




Front View

Back View



I2: Storage w/ Doors

Basis-of-Design: Manufacturer: KISeries: Ruckus Storage with DoorsModel No: Custom StorageDescription: Shell

Steel Base Shell Components consist of top, bottom, sides, back uprights,bottom and top reinforcements, spot welded and metal insert gas (MIG)welded together. The top of the cabinet is 19-gauge cold-rolled steel (C.R.S.)with 11/8” flanges, on four sides. The front face has an additional flangeformed inward to provide additional strength. The back of the cabinet is20-gauge C.R.S. and is formed on four sides to provide strength. The bottomis 20-gauge C.R.S. with a flush upper surface and flanged downward to providea welding surface with the sides and back. The front face is formed down 11/8”and inward to provide additional strength. Each shell has double wall sides from20-gauge C.R.S.; the inner panels of tote units are pierced on approximately3 3 /4” centers to allow molded plastic slide rails to be attached for totes. Thecubby units are punched to accept fixed shelves dividing the section in half. Thefront flange of the outer side panels are formed to fit inside the channel formationof the side panel; the rear edge is offset formed for maximum strength and a flushalignment with the back return. Each shell has 18-gauge front and back uprightmembers spot welded to the sides providing vertical strength. Top reinforcementsare spot welded to the top and MIG welded to the vertical upright members toprovide resistance against racking. Center partitions are two piece 20-gauge steelfabricated panels spot welded together with apposing flanges to be screw mountedto the top and bottom panels of the shell, punches with a matching pattern to theside of the units. The bottom is fitted with two 18-gauge MIG welded in placestructurally formed reinforcements which are located along the front and back ofthe cabinet. The reinforcements have two U-channel inner reinforcements withextruded holes to accept the tri-lobe screws that affix the casters. Double-facedunits are created using two single-faced units placed back-to-back, joined by aEach unit has four industrial grade casters with 75 mm grey non-markingthermoplastic rubber wheels with a 25 mm tread. Casters are plate mountedwith double ball bearing swivel head and a housing made of bright zinc platedpressed steel. The two front casters are total locking preventing swivel as wellas rolling, the two rear casters are swivel and free rolling. The overall height ofthe casters are 100 mm.The doors are single wall construction with a structural hinge channel runningthe length of the door. Self-closing European style hinges with 110-degree swing,provide 3-way adjustment of door to ensure consistent gapping and operation.Each steel door is standard with a key lock. All doors are inset. Beveled door pull is made from cast zinc. It mounts using two machine screws toa steel door.

1. VS America





Totes:(8)-6" Toes with rail included

Glides: AdjustableWarranty: 15 YearShell Color: CG Cool GreyTop Color: CG Cool GreyShelf Color: CG Cool GreyDoors: CY Cayenne

Description Dimensions Room# Qty2 Column Unit 30" x 18" x 40-3/4" 1064 2



I3: Teacher Bookcase

Basis-of-Design: Manufacturer: FleetwoodSeries: Illusion

Description: Teacher Bookcase¾” thick 45lb. multi-density particleboard substrate with a balancedconstruction of color-matched, thermally fused laminate (TFL) on both sides of all horizontal and vertical outer and internal panels onshelving units and shelves.Permanently attached 3mm color-matched or coordinating PVC edgeband with ergonomic 1/8” radius top edge bonded with hot-melt adhesiveand trimmed flush on top, bottom and sides of Zinc metal L-bracket andscrew butt-joint construction with screws contained to inside of unit. #10sized screws utilized. ¾” thick particleboard shelving secured with metal screws so shelving cannot be accidently dislodged. Shelf placement holeson 32mm increments to allow for shelf repositioning in field.

Laminate: Wilsonart-Florence Walnut 7993-38Edge Band: GraphiteWarranty: Limited Lifetime

Model No. Deminsions Shelves Room# Qty1600945-238 48"W x 34"H x 14"D 2 total, All Typical Classrooms 134

1 adjustable 1050(2), 1051(2), 1052(2), 1057, 481059, 1091(2), 1093(2),2008(2),2010(2), 2011, 2016, 2017(2), 2080(2), 2090(2), 2091(2), 2107(2), 2108(2), 3004(2), 3009(2), 3016(2), 3089(2), 3092(2), 3093(2), 3096(2), 3104(2), 3105 (2)



1. Herman Miller



I4: Bookcase

Basis-of-Design: Description: The top is 19-gauge cold-rolled steel (C.R.S.) with 11 /8" flanges, on three

sides. The front face has an additional flange formed inward to provide additional strength. The back edge is offset formed to accept the top flange of the back. The back is 20-gauge C.R.S. and is formed on four sides to provide a flush seamless back surface. The flanges are located inthe offset of the top and sides to provide a flush surface. The bottom isalso 19-gauge C.R.S. with a flush upper surface and flanged downward toprovide a welding surface with the sides and back. The front face is formeddown 11 /8" and inward to provide additional strength.

Manufacturer: KISeries: 700 SeriesWarranty: 15 Year

Model No. Dimensions Shelves Room# QtyS7B/3625515 36"W x 28"H x 15"D 1 1064 2



1. Herman Miller



I5: Executive Bookcase

Basis-of-Design: Description: Thermally-Fused Laminate (TFL) and High Pressure Laminate (HPL) are made

of solid colors and woodgrain laminates fused to particleboard core. Eachlaminate offers lasting beauty, superior resistance to normal wear, and easymaintenance. Tops: 1" thick TFL or HPL with 3mm matching PVC rimscontoured to selected profile and 1mm PVC rims on self edges. Graindirection runs left-to-right, unless otherwise noted. Chassis: Chassis arefastened by using high quality European fastening systems to assure maximumstrength. All units ship with heavy- duty, adjustable glides to ensure properleveling and compensation for uneven floors.

Manufacturer: IndianaSeries: CanvasModel No: 66-3672BCDimensions: 36" x 72"Warranty: 12 Year


Laminate Room# QtyShaker Cherry-SKCP 1136, 2086, 3083 3

1. Herman Miller





I6 Storage Cubbies

1. Brodart2. Steelcase

Basis of Design:Manufacturer: Media TechnologiesSeries: Custom UnitDescription: Wall attached Storage Cubbies

72 Individual cubbies on this unit and includes 1" thick fixed shelves with each cubie measuring 9"W x 14"D x 12"H.Laminate over plywood core.

Dimensions: 108"W x 24"D x 42"HLaminate: WilsonartColor: Pewter Mesh 4878-38Warranty:


Dimensions Room# Qty108"W x 79"H x 14"D 1023 1





I7 Cash Register Unit with Storage

1. Brodart2. Steelcase

Basis of Design:Manufacturer: Media TechnologiesSeries: Custom Unit

Description: Wall attached Storage Cubbies72 Individual cubbies on this unit and includes 1" thick fixed shelves with each cubby measuring 9"W x 14"D x 12"H.Laminate over plywood core.

Dimensions: 108"W x 24"D x 42"HLaminate: WilsonartColor: Pewter Mesh 4878-38Warranty: 10 Year


Dimensions Room# Qty108"W x 79"H x 14"D 1023 1





I8 4-Sided Display

Basis of Design:Manufacturer:Series:Warranty:Laminate:Description:

1077 1



I9: Metal Shelving

1. Uline2. Global

Basis of Design:Manufacturer: PencoSeries: ClipperWarranty: 1 Year

Description: OOFFSET ANGLE:

GGENERAL:

PPOSTS:

BBOX POST:

SSWAY BRACES:



I10: Industrial Metal Shelving

1. Uline2. Global

Basis of Design:Manufacturer: GladiatorSeries: Heavy Duty Mega RackModel No: GARA904XIG

Description: Heavy duty free standing shelving unit.8000lbs total distributed weight capacity and up to 2000lbs per shelf.Four adjustable shelves.

Dimensions: 90"W x 24"D x 90"HColor: Steel GreyWarranty: Lifetime Limited Warranty

Dimension Room# Qty90"W x 24"D x 90"H 1041(7), 1047(2), 1048(2), 1050(6) 17





I11: Metal Lockers

1. Debourgh2. Lyon

Basis of Design:Manufacturer: PencoModel No: Gen2Warranty: 1 Year

Description: Fully Welded Lockers with bases and 14-guage doors. Built-in combo Locks.The lockers are the Welded Gen2 locker. w/4” integral channel bases and continuous sloping hoods.They have a recessed handle with a multi-point lift latch. h of each locker opening.The lockers are equipped with continuous hinges running the full length of eachlocker.

Dimensions Description Frame Qty. Room# Locker Qty.15" x 15" x 72" 2-Tier 20 1026 4015" x 15" x 72" 3-Tier 12 1055 3615" x 15" x 72" 2-Tier 16 1062 3215" x 15" x 72" 6-Tier 11 2096 66





2.3.10 EQUIPMENT

J1 Dance Mat J2 Peg Board J3 Three Panel Mirror J4 Choral Risers



J1 Portable Dance Floor

Basis-of-Design: Manufacturer: Marley Floor by AlvasSeries: Matlay Vinyl Dance FloorModel No: BAL-MDF-6X20GYBK

Description: Lightweight Vinyl dance floor with a non-skid matte finish. Made of PVC dance vinyl. Phthalate free. Class 1 fire rated.

Weight: .33lbs /sf.Thickness: 1mmWarranty: 5 Year

Dimension Room# Qty6' x 20' 1019 10

1. Rosco





J2: Peg Board

Basis-of-Design: Manufacturer: Leornard Peterson Co.Model No: #B-12

Description: Epoxy Resin Pegboards with Stainlessdrip through.

Dimensions: 32" x 30"Warranty: 1 YearDimensions: 32" x 30"

Furniture Code Dimension Room# QtyPB 1019 10

1. DurconSubstitution Procedures.



J3: Three Panel Mirror

Basis-of-Design: Manufacturer: Hitchcock ButterfieldModel No: Empyrean MirrorDescription: 3 Panel wall mount mirror with frame on all sides.

Dimensions: 72"H x 62"W x *"D Color: SilverWarranty: 1Year

Dimension Room# Qty72"H x 62"W x *"D 1024 1


1. Granger




J4: Choral Risers

Basis-of-Design: Manufacturer: SicoSeries: Harmony Choral RiserModel No: #2610-324

Description: Rear security guardrail that are permanently attached. Non reflective frame finish. Mobile 4 wheel design. Deck to deck overhang. Non-marking glides. Carpet wrapped deck. Deck frames are welded aluminum. Simply design forfolding. Unit to unit cam-connector. Quick reverse steps.

Dimensions: 72.5”W x 55.5”DWarranty: 15 Year

Room# Qty.1029 5

1. Wenger





PART 3 - EXECUTION

3.1 PREPARATION

A. Site Verification of conditions.

1. Verify site is ready for installation of furniture items.

2. Coordinate shipping and receiving times with designated Owner’s representative.

3.2 INSTALLATION

A. General: Installation shall be performed by the Contractor.

1. Contractor shall install furniture in locations shown on plans. Contractor shall reposition or reorient furniture as requested by Owner. Final furniture install plans will be provided once the bid has been awarded.

2. Contractor is responsible for the clean-up and removal of all cartons and packaging associated with this furniture.

3. Contractor is responsible for any damage to the facility during installation. The Contractor will be responsible to repair any damages to the Owner’s satisfaction.

3.3 FIELD QUALITY CONTROL

A. Special Inspector

1. Owner shall appoint an inspector to verify that installed products match the quality standard established by the sample mock-up (if required) and/or meet the specification criteria as set forth in the document and/or by reference in the quality standards.

3.4 ADJUSTMENT & CLEANING

A. Remove and replace or repair damaged surfaces or defects in finished products to match similar undamaged products.

B. Remove and replace, or repair damaged wood, finishes or hardware components.

C. Upon completion of installation, contractor to check for complete function of parts and finish.

D. Perform final walk-through with inspector, documenting acceptance of furniture, installation and clean up.



04/09/2021 PROJECT MANUAL FOR: New Lowndes High School ...

Documents

Transcript of 04/09/2021 PROJECT MANUAL FOR: New Lowndes High School ...