03C- Extended Surfaces
-
Upload
yuneo-nurcahya -
Category
Documents
-
view
66 -
download
0
Transcript of 03C- Extended Surfaces
![Page 1: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/1.jpg)
Chapter 3
Extended Surfaces / Fins
![Page 2: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/2.jpg)
Chapter 3
Extended Surfaces (Fins)
An extended surface (also known as a combined conduction-convection system or a fin) is a solid within which heat transfer by conduction is assumed to be one dimensional, while heat is also transferred by convection (and/or radiation) from the surface in a direction transverse to that of conduction
36
![Page 3: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/3.jpg)
Chapter 3
Heat Transfer from Extended Surfaces
• Extended surfaces may exist in many situations but are commonly used as fins to enhance heat transfer by increasing the surface area available for convection (and/or radiation).
37
![Page 4: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/4.jpg)
Chapter 3
Typical Fin Configurations
38
![Page 5: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/5.jpg)
Chapter 3
Fins of Uniform Cross-Sectional AreaAssuming one-dimensional, steady-state conduction in an extended surface of constant conductivity and uniform cross-sectional area with negligible generation and radiation, the fin equation is of the form:
02
2
)( TTkA
hP
dx
Td
c
where p is the fin perimeter
39
TTbb
TxT )(
Define:
(3.6.1)
![Page 6: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/6.jpg)
Chapter 3
Boundary Conditions
• At the base T = Tb or (0)=b
• At the tip:Case A: Convection heat transfer
Case B: Adiabatic tip
Case C: Prescribed temperature, (L)=L
Case D: Infinite fin, T(L)=T or (L)=
Case A
40
![Page 7: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/7.jpg)
Chapter 3
Solutions of Differential Equation
)( TThPkAq bcf
41
(3.6.2)
![Page 8: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/8.jpg)
Chapter 3
True or False?
• Heat is transferred from hot water flowing through a tube to air flowing over the tube. To enhance the heat transfer rate the fins should be installed on the tube interior surface (the hot water side)
• Fins are particularly beneficial when h is small (typical for a gas or when only natural convection exists).
• Ideally the fin material should have a large thermal conductivity to minimize temperature variations from its base to its tip.
![Page 9: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/9.jpg)
Chapter 3
Selection of fin material (Example 3.9)
kCu>kAl>kSS
(1)
(2)
(3)
SS
Al
Cu
![Page 10: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/10.jpg)
Chapter 3
Example: Problem 3.116
Assessment of cooling scheme for gas turbine blade. (a) Determine whether the blade temperature is less than the maximum
allowable value (1050 °C) for the prescribed operating conditions (b) Evaluate blade cooling rate.
Assume that convective heat losses from the surface are negligible, i.e. adiabatic tip condition.
42
![Page 11: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/11.jpg)
Chapter 3
Fin Performance
• Fin effectiveness: Ratio of the fin heat transfer rate qf to the heat transfer rate that would exist without the fin
bbc
ff hA
q
,
f should be as large as possible (at least >2)
• For a very long (infinite) fin (Case D boundary condition):
21 /
cf hA
kP
where b=Tb-T, and Ac,b is the fin cross-sectional area at the base
43
(3.6.3)
(3.6.4)
![Page 12: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/12.jpg)
Chapter 3
Fin Performance
ft
b
ft
bf RR
TTq
,,
• Fin heat transfer rate:
where Rt,f is the fin resistance
Can express fin effectiveness as a ratio of thermal resistances:
ft
btf R
R
,
, where Rt,b is the resistance due to convection of the exposed base (=1/hAc,b)
44
![Page 13: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/13.jpg)
Chapter 3
Fin Performance• Fin efficiency: The ratio of the actual heat transfer rate from the fin to the
maximum rate at which a fin could dissipate energy
bf
fff hA
q
q
q
max
See Table 3.5 and Figures 3.18 and 3.19 for the efficiencies of common fin shapes
ffft hA
R
1,
We can use the efficiency to calculate the fin resistance
45
(3.6.5)
(3.6.6)
![Page 14: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/14.jpg)
Chapter 3
Fin Arrays• Define the overall efficiency, o as
)( ft
fo A
NA 11
where N is the number of fins in the array, Af the surface area of each fin and At the total surface area.
• We can then calculate the heat rate for the fin array
btot hAq
• Thermal resistance of the fin array
toot hA
R
1,
)( ft
fo A
NA 11
46
bt
tto hA
q
q
q
max
(3.6.7)
(3.6.8)
(3.6.9)
![Page 15: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/15.jpg)
Chapter 3
Fin Manufacturing
Care must be exercised to ensure that the thermal contact resistance does not adversely influence the overall fin performance
47
![Page 16: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/16.jpg)
Chapter 3
ExampleAs more components are placed on a single integrated circuit (chip), the amount of heat dissipated increases. The maximum allowable chip operating temperature, is approximately 75°C. Suggest ways to maximize heat dissipation.
Top view Side view
Air, T=20°C
48
![Page 17: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/17.jpg)
Chapter 3
Fins in Heat Exchangers
• Widely used to achieve large heat rates per unit volume, particularly when one or both fluids is a gas.
• Characterized by large heat transfer surface areas per unit volume (>700 m2/m3), small flow passages, and laminar flow.
![Page 18: 03C- Extended Surfaces](https://reader035.fdocuments.in/reader035/viewer/2022081715/545d775db1af9f410a8b4bcb/html5/thumbnails/18.jpg)
Chapter 3
Fin (extended surface) effects
• Fins reduce the resistance to convection heat transfer, by increasing surface area.
• The expression for the overall heat transfer coefficient includes overall surface efficiency, or temperature efficiency, o, of the finned surface, which depends on the type of fin (see also Ch. 3.6.5)
hoho
hfconduction
co
cf
co hAA
RR
A
R
hAUA )()()()(
",
",
111
(11.5)
where c is for cold and h for hot fluids respectively