022/1 SoLeNoid VALVeS SpA FP-22-PD-*-02/03-*-* U Type Sez ......SoLeNoid VALVeS 2 Way, Double Lock,...
Transcript of 022/1 SoLeNoid VALVeS SpA FP-22-PD-*-02/03-*-* U Type Sez ......SoLeNoid VALVeS 2 Way, Double Lock,...
-
Page 56 www.thehydraulicwarehouse.com.au
Content is subject to change without notice. Please refer to our website for the most current product information.
SoLeNoid VALVeS
Materials Cartridge = steel zinc platedInternal parts = hardened steel
Flow Range 2-70 LPM
Max. Pressure 350 bar (Coil 20 W)250 bar (Coil 18 W)
Installation Torque 45-55 Nm
Cavity 21261, refer to cavity information on page 65
Cartridge Weight 0.230 kg
Coils Version C-13, refer to coil information on page 64Oil Temperature Range -20°C + 80°C
Recommended Filtration
Nominal max. 10μ, ISO 4406-19/17/14 (NAS8) or less
Ambient Temperature Range -30°C + 60°C
Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Technical Specifications Pressure drop Curves
Oil viscosity 24 mm2/sec. (3.5 oE) Temperature 50 oCValve open (energised coil)
2 Way, Double Lock, Normally Closed Poppet ValveFP-22-PD-G3/4-02
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, doppia tenuta, normalmente chiusa, filettatura gas2 way, pilot operated electric valve, double lock poppet, normally closed, bsp thread
FP-22-PD-*-02/03-*-* UUUUU 022/1
Rev.00-2013/05
2
1
02
2
1
03
NEW 2013
Flu id-P ress S .p .A . - Web: http : / /www.�uidpress . i t - E-mai l : in fo@�uidpress . i t
Tipo / Type Sez./ Section Pag./ PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10 µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended �ltration: nominal max. 10 µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage �uctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, doppia tenuta, normalmente chiusa, �lettatura gas2 way, pilot operated electric valve, double lock poppet, normally closed, bsp thread
FP-22-PD-*-02/03-*-* UUUUU 022/1
Rev.00-2013/05
2
1
02
2
1
03
NEW 2013
Flow (LPM)
Pre
ssur
e Δ
p (b
ar)
-
Page 57www.thehydraulicwarehouse.com.au
Content is subject to change without notice. Please refer to our website for the most current product information.
SoLeNoid VALVeS2 Way, Double Lock, Normally Closed Poppet ValveFP-22-PD-G1-02
Materials Cartridge = steel, zinc platedInternal parts = hardened steel
Flow Range 4-150 LPM
Max. Pressure 350 bar (Coil 20 W)250 bar (Coil 18 W)
Installation Torque 60-70 Nm
Cavity 21331, refer to cavity information on page 65
Cartridge Weight 0.340 kg
Coils Version C-13, refer to coil information on page 64Oil Temperature Range -20°C + 80°C
Recommended Filtration
Nominal max. 10μ, ISO 4406-9/17/14 (NAS8) or less
Ambient Temperature Range -30°C + 60°C
Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Technical Specifications Pressure drop Curves
Oil viscosity 24 mm2/sec. (3.5 oE) Temperature 50 oCValve open (energised coil)
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, doppia tenuta, normalmente chiusa, filettatura gas2 way, pilot operated electric valve, double lock poppet, normally closed, bsp thread
FP-22-PD-*-02/03-*-* UUUUU 022/1
Rev.00-2013/05
2
1
02
2
1
03
NEW 2013
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, doppia tenuta, normalmente chiusa, filettatura gas2 way, pilot operated electric valve, double lock poppet, normally closed, bsp thread
FP-22-PD-*-02/03-*-* UUUUU 022/1
Rev.00-2013/05
2
1
02
2
1
03
NEW 2013
Flu id-P ress S .p .A . - Web: http : / /www.�uidpress . i t - E-mai l : in fo@�uidpress . i t
Tipo / Type Sez./ Section Pag./ PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10 µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended �ltration: nominal max. 10 µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage �uctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente chiusa, �lettatura gas2 way, pilot operated electric valve, normally closed, bsp thread
FP-22-CP-*-05/06/07/08-*-* UUUUU 052/1
Rev.00-2012/07
2
1
05
2
1
06
2
1
07
2
1
08
NEW 2013
Flow (LPM)
Pre
ssur
e Δ
p (b
ar)
-
Page 58 www.thehydraulicwarehouse.com.au
Content is subject to change without notice. Please refer to our website for the most current product information.
SoLeNoid VALVeS
Pressure drop Curves
Materials Cartridge = steel, zinc platedInternal parts = hardened steel
Flow Range 1-50 LPM
Max. Pressure 350 bar (Coil 20 W)250 bar (Coil 18 W)
Installation Torque 35-45 Nm
Cavity 23081, refer to cavity information on page 65
Cartridge Weight 0.140 kg
Coils Version C-13, refer to coil information on page 64Oil Temperature Range -20°C + 80°C
Recommended Filtration
Nominal max. 10μ, ISO 4406-19/17/14 (NAS8) or less.
Ambient Temperature Range -30°C + 60°C
Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Technical Specifications
Flu
id-P
ress
S.p
.A.
- W
eb:
http
://w
ww
.flu
idpr
ess.
it -
E-m
ail:
inf
o@fl
uidp
ress
.it
Tipo
/Typ
eSe
z./Se
ctio
nPa
g./P
age
FLU
ID-P
RES
S Sp
A
Solu
tion
in M
otio
n
SPEC
IFIC
HE T
ECN
ICH
EMa
terial
i: ca
rtucc
ia in
accia
io zin
cato.
Com
pone
nti in
terni
inac
ciaio
tratta
to ter
mica
mente
.Ca
mpo d
i port
ata:
3/4: 2
-70 L/
min;
1”: 4-
150 L
/min
Pres
sione
max
.: 350
bar (
Bobin
a 20 W
), 250
bar (
Bobin
a 18 W
)Co
ppia
di se
rragg
io in
cavit
à: ve
dere
pag.2
Cavit
à: ve
dere
sezio
ne X
Peso
cartu
ccia:
vede
re pa
gina 2
Bobin
e: ve
rsion
e C-13
, ved
ere se
zione
YTe
mpera
tura o
lio: -2
0°C +
80°C
Temp
eratur
a amb
iente:
-30°
C + 60
°CFil
trazio
ne co
nsigl
iata:
nomi
nale
max.
10µ,
ISO
4406
-19/17
/14(N
AS8)
o mi
nore
La va
riazio
ne d
i volt
aggio
in in
gress
o no
n de
ve e
cced
ere il
±10%
del v
alore
nomi
nale.
TEC
HN
ICA
L SP
ECIF
ICAT
IONS
Mater
ials:
cartri
dge i
n stee
l zinc
plate
d, int
ernal
parts
in ha
rdene
dste
el.Flo
w ran
ge:
3/4: 2
-70 L/
min;
1”: 4-
150 L
/min
Max.
pres
sure:
350 b
ar (C
oil 20
W), 2
50 ba
r (Co
il 18 W
)Ins
tallat
ion to
rque
: see
page
2Ca
vity:
see s
ectio
n XCa
rtridg
e weig
ht: se
e pag
e 2Co
ils: v
ersion
C-13
, see
secti
on Y
Oil te
mpera
ture:
-20°C
+ 80
°CAm
bient
tempe
ratur
e ran
ge: -3
0°C +
60°C
Reco
mmen
ded f
iltrati
on: n
omina
l max
. 10µ
, ISO
4406
-19/17
/14(N
AS8)
or les
s.Inl
et vo
ltage
fluctu
ation
s mus
t not
exce
ed ±1
0% of
nomi
nal v
oltag
e.
Valv
ola
elet
trica
2 vi
e, p
ilota
ta, d
oppi
a te
nuta
, nor
mal
men
te ch
iusa
, file
ttatu
ra g
as2
way
, pilo
t ope
rate
d el
ectri
c va
lve, d
oubl
e lo
ck p
oppe
t, no
rmal
ly cl
osed
, bsp
thre
ad
FP-2
2-P
D-*
-02/0
3-*
-*UUUU U
022/
1
Rev
.00-
2013
/05
2 1
02
2 1
03
NE
W2013
Flu
id-P
ress
S.p
.A.
- W
eb:
http
://w
ww
.flu
idpr
ess.
it -
E-m
ail:
inf
o@fl
uidp
ress
.it
Tipo
/Typ
eSe
z./Se
ctio
nPa
g./P
age
FLU
ID-P
RES
S Sp
A
Solu
tion
in M
otio
n
UUUU U02
2/2
Valv
ola
elet
trica
2 vi
e, p
ilota
ta, d
oppi
a te
nuta
, nor
mal
men
te ch
iusa
, file
ttatu
ra g
as2
way
, pilo
t ope
rate
d el
ectri
c va
lve, d
oubl
e lo
ck p
oppe
t, no
rmal
ly cl
osed
, bsp
thre
ad
FP-2
2-P
D-*
-02/0
3-*
-*
Rev
.00-
2013
/05
ESEM
PIO
DI O
RDIN
AZIO
NE -
ORDE
RING
COD
E EX
AMPL
E
F P
2
2
P D
3
/ 4
0
2
**
3/4 –
3/4“ B
SPP
Gu
arnizio
ni – Se
als:
1 – 1“
BSPP
V=Vit
on
Dimen
sione
- Dime
nsion
Omette
re se B
UNA-N
– Omit
if BUN
A-N*
*
02 – d
oppia t
enuta,
norma
lmente
chius
a – no
rmally
closed
, dual s
eal
Emerg
enza
– Man
ual ov
erride
03 – d
oppia t
enuta,
norma
lmente
chius
a, extra
molla
– norm
ally clo
sed, du
al seal
, extra
spring
S = vit
e - sc
rew
Sche
ma idr
aulico
– Hy
draulic
sche
me
Omette
re se n
on rich
iesta –
Omit if
not req
uired
* *
A B
C D
E F
H CA
VITA’
CAVIT
Y CO
PPIA D
I SERR
AGGIO
INS
TALLA
TION T
ORQU
E PE
SO
WEIGH
T TIP
O
TYPE
mm
BS
P mm
mm
mm
mm
mm
Nm
Kg
FP-22
-PD-
3/4”-0
2/03
23.5
3/4”
39.5
14.5
9.5
102
32
2126
1 45
– 55
0.2
30
FP-22
-PD-
3/4”-0
2/03-S
23
.5 3/4
” 39
.5 14
.5 9.5
10
2 32
21
261
45 –
55
0.240
FP
-22-P
D-1”-
02/03
30
1”
49.5
14
9.5
111.5
38
21
331
60 –
70
0.340
FP
-22-P
D-1”-
02/03
-S
30
1” 49
.5 14
9.5
11
1.5
38
2133
1 60
– 70
0.3
50
2 Way, Double Lock, Normally Closed Poppet ValveFP-22-PD-S08-02
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, doppia tenuta, normalmente chiusa, filettatura gas2 way, pilot operated electric valve, double lock poppet, normally closed, bsp thread
FP-22-PD-*-02/03-*-* UUUUU 022/1
Rev.00-2013/05
2
1
02
2
1
03
NEW 2013
2
1
27.7
18.5 94
.29.
524
Ø13
Oil viscosity 24 mm2/sec. (3.5 oE) Temperature 50 oCValve open (energised coil)
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:S08: 1-50 L/min; S10: 5-70 L/min; S12: 10-140 L/minPressione max.: 350 barCoppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:S08: 1-50 L/min; S10: 5-70 L/min; S12: 10-140 L/minMax. pressure: 350 barInstallation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, doppia tenuta, normalmente chiusa2 way, pilot operated electric valve, double lock poppet, normally closed
FP-22-PD-*-02/03-*-* UUUUU 020/1
Rev.01-2014/09
2
1
02
2
1
03
NEW 2013
Flow (LPM)
Pres
sure
Δp
(bar
)
3/4"-16uNF-2A12.7
-
Page 59www.thehydraulicwarehouse.com.au
Content is subject to change without notice. Please refer to our website for the most current product information.
SoLeNoid VALVeS
Materials Cartr parts = hardened steel
Flow Range 2-70 LPM
Max. Pressure 350 bar (Coil 20 W) 250 bar (Coil 18 W)
Installation Torque 45-55 Nm
Cavity 21261, refer to cavity information on page 65
Cartridge Weight 0.230 kg
Coils Version C-13, refer to coil information on page 64Oil Temperature Range -20°C + 80°C
Recommended Filtration
Nominal max. 10μ, ISO 4406-19/17/14 (NAS8) or less
Ambient Temperature Range -30°C + 60°C
Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Technical Specifications Pressure drop Curves
Oil viscosity 24 mm2/sec. (3.5 oE)Valve open (energised coil) Temperature 50 oC
2 Way, Normally Closed Poppet ValveFP-22-CP-G3/4-06
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente chiusa2 way, pilot operated electric valve, normally closed
FP-22-CP-*-05/06/07/08-*-* UUUUU 050/1
Rev.00-2012/06
2
1
05
2
1
06
2
1
07
2
1
08
NEW 2013
Flu id-Press S .p .A . - Web: http : / /www.�uidpr e ss . i t - E-mai l : in f o@�uidpr e ss . i t
Tipo / Type Sez./ Section Pag./ PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10 µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended �ltration: nominal max. 10 µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage �uctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente chiusa, �lettatura gas2 way, pilot operated electric valve, normally closed, bsp thread
FP-22-CP-*-05/06/07/08-*-* UUUUU 052/1
Rev.00-2012/07
2
1
05
2
1
06
2
1
07
2
1
08
NEW 2013
Flow (LPM)
Pres
sure
Δp
(bar
)
-
Page 60 www.thehydraulicwarehouse.com.au
Content is subject to change without notice. Please refer to our website for the most current product information.
SOLENOID VALVES
Materials Cartridge = steel, zinc plated Internal parts = hardened steel
Flow Range 4-150 LPM
Max. Pressure 350 bar (Coil 20 W) 250 bar (Coil 18 W)
Installation Torque 60-70 Nm
Cavity 21331, refer to cavity information on page 65
Cartridge Weight 0.340 kg
Coils Version C-13, refer to coil information on page 64Oil Temperature Range -20°C + 80°C
Recommended Filtration
Nominal max. 10μ, ISO 4406-19/17/14 (NAS8) or less
Ambient Temperature Range -30°C + 60°C
Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Technical Specifications Pressure drop Curves
Oil viscosity 24 mm2/sec. (3.5 oE) Temperature 50 oCValve open (energised coil)
2 Way, Normally Closed Poppet Valve FP-22-CP-G1-06
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente chiusa, filettatura gas2 way, pilot operated electric valve, normally closed, bsp thread
FP-22-CP-*-05/06/07/08-*-* UUUUU 052/1
Rev.00-2012/07
2
1
05
2
1
06
2
1
07
2
1
08
NEW 2013
38
111.5
49
30G1
Flu id- P ress S .p .A . - Web: h t tp : / / www. �u i dpres s . i t - E-m ai l : i n f o@�u i dpres s . i t
Tipo / Type Sez./ Section Pag./ PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:3/4: 2-70 L/min; 1”: 4-150 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10 µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:3/4: 2-70 L/min; 1”: 4-150 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended �ltration: nominal max. 10 µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage �uctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente chiusa, �lettatura gas2 way, pilot operated electric valve, normally closed, bsp thread
FP-22-CP-*-05/06/07/08-*-* UUUUU 052/1
Rev.00-2012/07
2
1
05
2
1
06
2
1
07
2
1
08
NEW 2013
Flow (LPM)
Pres
sure
Δp
(bar
)
-
Page 62 www.thehydraulicwarehouse.com.au
Content is subject to change without notice. Please refer to our website for the most current product information.
SoLeNoid VALVeS
Pressure drop Curves
Materials Cartridge = steel, zinc platedInternal parts = hardened steel
Flow Range 0.5-50 LPM
Max. Pressure 350 bar (Coil 20 W), 250 bar (Coil 18 W)
Installation Torque 35-45 Nm
Cavity 23081, refer to cavity information on page 65
Cartridge Weight 0.135 kg
Coils Version C-13, refer to coil information on page 64Oil Temperature Range -20°C + 80°C
Recommended Filtration
Nominal max. 10µ, ISO 4406-19/17/14 (NAS8) or less
Ambient Temperature Range -30°C + 60°C
Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Technical Specifications
Oil viscosity 24 mm2/sec. (3.5 oE) Temperature 50 oC
2 Way, Normally Open Poppet ValveFP-22-CP-S08-16
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente aperta2 way, pilot operated electric valve, normally open
FP-22-CP-*-15/16-*-* UUUUU 150/1
Rev.00-2012/06
2
1
15
2
1
16
NEW 2013
3/4″ -16 UNF- 2A
12.7
92
16.5
27.5
24
Flu id-Press S .p .A . - Web: http : / /www.�uidpress . i t - E-mai l : in fo@�uidpress . i t
Tipo / Type Sez./ Section Pag./ PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10 µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended �ltration: nominal max. 10 µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage �uctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente aperta2 way, pilot operated electric valve, normally open
FP-22-CP-*-15/16-*-* UUUUU 150/1
Rev.00-2012/06
2
1
15
2
1
16
NEW 2013
Q (LPM)
Δp (b
ar)
-
Page 63www.thehydraulicwarehouse.com.au
Content is subject to change without notice. Please refer to our website for the most current product information.
SoLeNoid VALVeS
3/4″ -16 UNF- 2A
12.7
94
16.5
27.5
24
Pressure drop Curves
Materials Cartridge = steel, zinc platedInternal parts = hardened steel
Flow Range 0.5-50 LPM
Max. Pressure 350 bar (Coil 20 W)250 bar (Coil 18 W)
Installation Torque 35-45 Nm
Cavity 23081, refer to cavity information on page 65
Cartridge Weight 0.142 kg
Coils Version C-13, refer to coil information on page 64Oil Temperature Range -20°C + 80°C
Recommended Filtration
Nominal max. 10µ, ISO 4406-19/17/14 (NAS8) or less
Ambient Temperature Range -30°C + 60°C
Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Technical Specifications
Oil viscosity 24 mm2/sec. (3.5 oE) Temperature 50 oC
2 Way, Normally Open Poppet ValveFP-22-CP-S08-16-P
Flu id-Press S.p.A. - Web: ht tp: / /www.f lu idpress. i t - E-mai l : in fo@flu idpress. i t
Tipo /Type Sez./Section Pag./PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended filtration: nominal max. 10µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage fluctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente aperta2 way, pilot operated electric valve, normally open
FP-22-CP-*-15/16-*-* UUUUU 150/1
Rev.00-2012/06
2
1
15
2
1
16
NEW 2013
Fl u id- Pre ss S . p . A . - We b : h ttp : / /www. � uidp ress . i t - E- mai l : in fo@�u idpres s . i t
Tipo / Type Sez./ Section Pag./ PageFLUID-PRESS SpA
Solution in Motion
SPECIFICHE TECNICHEMateriali: cartuccia in acciaio zincato. Componenti interni inacciaio trattato termicamente.Campo di portata:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minPressione max.: 350 bar (Bobina 20 W), 250 bar (Bobina 18 W)Coppia di serraggio in cavità: vedere pag.2Cavità: vedere sezione XPeso cartuccia: vedere pagina 2Bobine: versione C-13, vedere sezione YTemperatura olio: -20°C + 80°CTemperatura ambiente: -30°C + 60°CFiltrazione consigliata: nominale max. 10 µ, ISO 4406-19/17/14(NAS8) o minoreLa variazione di voltaggio in ingresso non deve eccedere il ±10%del valore nominale.
TECHNICAL SPECIFICATIONSMaterials: cartridge in steel zinc plated, internal parts in hardenedsteel.Flow range:S08: 0.5-50 L/min; S10: 2-70 L/min; S12: 4-140 L/minMax. pressure: 350 bar (Coil 20 W), 250 bar (Coil 18 W)Installation torque: see page 2Cavity: see section XCartridge weight: see page 2Coils: version C-13, see section YOil temperature: -20°C + 80°CAmbient temperature range: -30°C + 60°CRecommended �ltration: nominal max. 10 µ, ISO 4406-19/17/14(NAS8) or less.Inlet voltage �uctuations must not exceed ±10% of nominal voltage.
Valvola elettrica 2 vie, pilotata, normalmente aperta2 way, pilot operated electric valve, normally open
FP-22-CP-*-15/16-*-* UUUUU 150/1
Rev.00-2012/06
2
1
15
2
1
16
NEW 2013
Flow (LPM)
Pre
ssur
e Δ
p (b
ar)
PH3570-Cartridge Valve PL_D9_web_Part58PH3570-Cartridge Valve PL_D9_web_Part59PH3570-Cartridge Valve PL_D9_web_Part60PH3570-Cartridge Valve PL_D9_web_Part61PH3570-Cartridge Valve PL_D9_web_Part62PH3570-Cartridge Valve PL_D9_web_Part64PH3570-Cartridge Valve PL_D9_web_Part65