01-06 Frame Configuration

8/20/2019 01-06 Frame Configuration

1/11

UA5000

Operation Manual - PVU Volume Contents

Issue 02 (2007-03-20) Huawei Technologies Proprietary i

Contents

6 Frame Configuration .................................................................................................................6-1

6.1 Overview of Frames......................................................................................................................................6-2

6.2 Frame Configuration .......................................................... .................................................................... .......6-3

6.2.1 Adding a Frame....................................................................................................................................6-3

6.2.2 Querying the Information of a Frame .................................................................... ..............................6-4

6.2.3 Adding an Inter-frame Connection.......................................................................................................6-4

6.2.4 Querying the Information about an Inter-frame Connection................................................................6-4

6.2.5 Deleting an Inter-frame Connection.....................................................................................................6-5

6.2.6 Deleting a Frame..................................................................................................................................6-5

6.3 Configuration Example .................................................................... ............................................................. 6-5

6.3.1 Networking ........................................................ ................................................................. .................6-6

6.3.2 Adding the Frames ................................................................ ............................................................... 6-6


2/11

Figures

UA5000

Operation Manual - PVU Volume

ii Huawei Technologies Proprietary Issue 02 (2007-03-20)

Figures

Figure 6-1 Sample connection among the master, slave and extended frames...................................................6-6


3/11

UA5000

Operation Manual - PVU Volume Tables

Issue 02 (2007-03-20) Huawei Technologies Proprietary iii

Tables

Table 6-1 Frames and backplanes.......................................................................................................................6-2

Table 6-2 Commands for configuring a frame....................................................................................................6-2


4/11


5/11

UA5000

Operation Manual - PVU Volume 6 Frame Configuration

Issue 02 (2007-03-20) Huawei Technologies Proprietary 6-1

6 Frame ConfigurationAbout This Chapter

The following table lists the contents of this chapter.

Section… Describes…

6.1 Overview of Frames The types of the UA5000 frames and the commands for

configuring a frame

6.2 Frame Configuration How to configure a frame

6.3 Configuration Example Example of configuring a frame


6/11

6 Frame Configuration

UA5000


6-2 Huawei Technologies Proprietary Issue 02 (2007-03-20)

6.1 Overview of Frames

There are three types of the UA5000 frames. They are master frame, slave frame and extendedframe.

A master frame can be connected with a slave frame and an extended frame to expand thesystem capacity.

A slave frame can be connected with an extended frame to expand the system capacity.

The slave frame needs to be added using the frame add command. The slot of the slaveframe is numbered from 0.

An extended frame can be seen as a logical extension of the master frame or the slaveframe it connects. The slots are numbered sequentially with that of the mater frame or theslave frame.

These three types of frames use different backplanes. See Table 6-1.

Table 6-1 Frames and backplanes

Frame Type Backplane Type Frame Alias

Rear-access master frame HABA MAIN_HABM_30

Front-access master frame HABD MAIN_HAFM_30

Rear-access master frame HABC MAIN_HABM_12

Front-access slave frame HABE SLAVE_HAFS_32

Front-access extended frame HABF -

Table 6-2 lists the commands for configuring a frame.

Table 6-2 Commands for configuring a frame

To… Use… In…

Add a frame frame add Global config mode

Add an inter-frame connection frame connect Global config mode

Delete an inter-frame connection [undo] frame connect Global config mode

Query the setting of inter-frame

connectiondisplay frame connect Global config mode

Query the setting of frames display frame info Global config mode

Delete a frame frame delete Global config mode

Configure frame attributes frame set Global config mode


7/11

UA5000



6.2 Frame Configuration

6.2.1 Adding a Frame

To configure a frame, you need to add it to the system first. To add a frame, use the frame add command. The frame with PVU card is the master frame, and the frame number is fixed as 0.

For example, to add a master frame whose frame type is MAIN_HAFM_30 (H601HABD), andadd a slave frame whose frame type is SLAVE_HAFS_32 (H602HABE), do as follows:

huawei(config)#frame add

{ frameid }:0

FrameType:

0 : MAIN_HAFM_30(H601HABD) 1 : MAIN_HAFM_6(H601HABL)

2 : MAIN_HABM_30(H601HABA) 3 : MAIN_HAFM_30(H602HABD)

4 : MAIN_HABM_12(H601HABC) 5 : SLAVE_HAFS_32(H601HABE)

6 : SLAVE_HABS_32(H601HABB) 7 : SLAVE_HABS_30(H601HABA)

8 : SLAVE_HAFS_30(H601HABD) 9 : SLAVE_HAFS_30(H602HABD)

10 : SLAVE_HAFS_32(H602HABE) 11 : RSU_HAFS_30(H601HABD)

12 : RSU_HABS_30(H601HABA) 13 : RSU_HAFS_6(H601HABL)

14 : RSU_HAFS_30(H602HABD) 15 : RSP_19(HCB)

16 : RSP_15(HDB) 17 : RSP_14(HIB)

18 : RSP_12(HFB) 19 : RSP_10(HGB)

20 : RSP_6A(HMB) 21 : RSP_6B(HLB)

22 : UAM_R (HUBM) 23 : UAS_R (HUBS)

24 : UAFM_R(HUBE) 25 : UAFS_R(HUBF)

26 : UABM_R(HUBB) 27 : ONU60A_R(HUBO)

28 : UAFX_R(HUBL)

Please select frame type (0 ~ 28):0

Frame add successfullyhuawei(config)#frame add 10

FrameType:









16 : RSP_15(HDB) 17 : RSP_14(HIB)

18 : RSP_12(HFB) 19 : RSP_10(HGB)





28 : UAFX_R(HUBL)


Frame add successfully

! FAULT MAJOR 2006-12-25 22:04:14 ALARM NAME :Frame fault

PARAMETERS :FrameID: 1


8/11


UA5000



Select correct frame type when adding a frame. Otherwise, the cards in the frame may not function

normally.

A slave frame is in fault state after it is added. You need to configure the inter-frame connection for the

frame to make it work normally.

6.2.2 Querying the Information of a Frame

To query the information of one or all frames, use the display frame info command.

For example, to query the information of all frames, do as follows:

huawei(config)#display frame info

{ desc|ts-information }:

{ info|link|connect }:info

{ |frameid }:

Command:

display frame info

----------------------------------------------------------------------------

FrameID FrameType FrameState

----------------------------------------------------------------------------

0 MAIN_HAFM_30(H601HABD) Normal

1 RSU_HAFS_30(H602HABD) Failed

----------------------------------------------------------------------------

Total: 2

6.2.3 Adding an Inter-frame Connection

The PVU card provides five 16 Mbit/s HWs to connect slave and extended frames. These HWs

are numbered 16 to 20. HW 16 is for the extended frame of this master frame. HWs 17 and 18are for the slave frames and their extended frames.

To add an inter-frame connection, use the frame connect command. In the UA5000 PVU, themaster frame is numbered 0 and the slave frames are numbered 1–8.

For example, to add an inter-frame connection between frame 0 and frame 1, do as follows:

huawei(config)#frame connect

{ upframeid }:0

{ downframeid }:1

Add the frame connection successfully

huawei(config)#

! RECOVERY MAJOR 2006-12-25 22:04:14 ALARM NAME :Frame recovery alarmPARAMETERS :FrameID: 1

6.2.4 Querying the Information about an Inter-frame Connection

To query the information about the inter-frame connection of one or all frames, use the display

frame connect command.

For example, to query the information about the inter-frame connections of all frames, do asfollows:

huawei(config)#display frame connect

{ |frameid }:


9/11

UA5000



Command:

display frame connect

---------------------------------------------

Record Upper-frame Lower-frame

---------------------------------------------

6.2.5 Deleting an Inter-frame Connection

To delete an inter-frame connection, use the undo frame connect command.

For example, to delete the link between frame 0 and frame 1, do as follows:

huawei(config)#undo frame connect

{ upframeid }:0

{ downframeid }:1

Changing the connection between frames will interrupt services,are you sure to

continue(y/n)[n]: y

Delete the frame connection successfully



6.2.6 Deleting a Frame

To delete a frame, use the frame delete command.

Before deleting a frame, you need to delete all configurations associated with the frame,

including services, line card, environment monitor unit, and inter-frame connections.

For example, to delete frame 1, do as follows:

huawei(config)#frame delete

{ frameid }:1 Are you sure to delete this frame? (y/n)[n]: y

Frame 1 delete successfully

6.3 Configuration Example

The configuration procedure is as follows:

Step 1 Add a frame.

Step 2 Add an inter-frame connection.

Step 3 Add line cards.

Step 4 Confirm the line cards.

----End


10/11


UA5000



6.3.1 Networking

Figure 6-1 shows the connection between the master frame (HABD), the slave frame (HABE)and the extended frames (HABF).

Figure 6-1 Sample connection among the master, slave and extended frames

E1/V5

Slave frame

Master frame

Extended frame of the slave frame

Extended frame of the master frame

HWOUT0

HWIN

HWINHWIN

HWOUT1

HWOUT2

A

S

L

A

S

L

D

S

L

D

S

L

H

WT

D

S

L

PSTN

P

V

U

A

S

L

A

S

L

D

S

L

P

V

U

D

S

L

H

WC

A

S

L

A

S

L

D

S

L

D

S

L

H

W

T

D

S

L

A

S

L

A

S

L

D

S

L

D

S

L

H

W

T

D

S

L

6.3.2 Adding the Frames

Step 1 Add a master frame, with the frame number of 0, and frame type of MAIN_HAFM_30(HABD).


{ frameid }:0

FrameType:









16 : RSP_15(HDB) 17 : RSP_14(HIB)

18 : RSP_12(HFB) 19 : RSP_10(HGB)





28 : UAFX_R(HUBL)

Please select frame type (0 ~ 28): 0


11/11

UA5000




You can use the display board 0 command to query the state of the card in the new frame.

Step 2 Add a slave frame, with the frame type of SLAVE_HAFS_32 (H602HABE).


FrameType:









16 : RSP_15(HDB) 17 : RSP_14(HIB)

18 : RSP_12(HFB) 19 : RSP_10(HGB)

20 : RSP_6A(HMB) 21 : RSP_6B(HLB)22 : UAM_R (HUBM) 23 : UAS_R (HUBS)



28 : UAFX_R(HUBL)





Step 3 Add an inter-frame connection.

huawei(config)#frame connect 0 1

Add the frame connection successfully

Step 4 Add line cards.

Add line cards for the master, slave and extended frames according to the data planning. The

command used is board add. Following is an example.

huawei(config)#board add 0/14 asl


……



Step 5 Confirm the line cards.

huawei(config)#board confirm 0

huawei(config)#board confirm 1

----End

01-06 Frame Configuration

Documents

Transcript of 01-06 Frame Configuration