— Rev PS48/PS80 Advantage Series Salt Based … Power Source - For safety reasons the outlet must...

Owner’s ManualPS48/PS80 Advantage Series

Salt Based Water Softeners

PS48/PS80 Advantage Series Salt Based Water Softeners— Rev N

© Copyright 2015 Enviro Water Solutions LLC. All rights reserved.

All information contained herein is the property of Pelican Water Systems. Pelican Water Systems makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Pelican Water Systems shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. The information is provided “as is” without warranty of any kind and is subject to change without notice. This document contains proprietary information which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Pelican Water Systems. Pelican Water Systems is an Enviro Water Solutions LLC Company.

© 2015 Enviro Water Solutions LLC3060 Performance Circle, Suite 2. DeLand, FL 32724

www.pelicanwater.com(877) 842-1635




Table of ContentsTable of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Product Operation and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Complete Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Bypass Valve Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Install Electronic Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Final Setup and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Complete the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Programming the Electronic Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 1: Setting the Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Step 2: Setting the Hardness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Step 3: Performing Manual Regeneration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adding the Pelican Logo Sticker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Warranty Registration Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14


Product Operation and Specifications

Important Information Read these instructions carefully and determine the location of all system components before

beginning installation. Check all applicable plumbing, building, and electrical codes for installation compliance. Install the system on the main water supply. Turn Electricity to Water Heater off. Systems that contain electronic components cannot be installed outside in uncovered areas. The use of Teflon Tape and/or Pipe Thread Seal Paste will be needed on all threaded connections.

If this or any other system is installed in a metal (conductive) plumbing system, i.e. copper or galvanized metal, the plastic components of the system will interrupt the continuity of the plumbing system. As a result any errant electricity from improperly grounded appliances downstream or potential galvanic activity in the plumbing system can no longer ground through contiguous metal plumbing. Some homes may have been built in accordance with building codes, which actually encouraged the grounding of electrical appliances through the plumbing system. Consequently, the installation of a bypass consisting of the same material as the existing plumbing, or a grounded "jumper wire" bridging the equipment and re-establishing the contiguous conductive nature of the plumbing system must be installed prior to your system’s use.

CAUTION:When adding a filtration/softening system to homes/buildings supplied by well water, the system should be installed following the pressure tank. DO NOT USE this system for pneumatic or hydro pneumatic applications. If you are using a booster pump, then install this system following the booster pump. If you have questions, please call customer service.

Specification Description

Rated Service Flow 12-18 GPM (depending on model)

Minimum Working Pressure 25 PSI

Maximum Working Pressure 80 PSI

Maximum Vacuum 5 inch/127 mm Hg

Operating Temperatures 36°F - 100°F

pH Range 6.5 - 11

WARNING:




Complete Parts ListNote: Pelican Water Systems supplies the parts below to accommodate a variety of water supply lines.

Table 1: Parts List

Note: Drawings are not to scale.

Additional fittings will be needed to adapt to your plumbing.

Part Description Qty. Part Description Qty.

Bypass Valve for Electronic Head

1 2

PVC Tubing Drain Line (50 ft.)

1 Electronic Head 1

Brine Tank 1 Softener Tank 1

Non-Abrasive Auto Wax

4 oz. Bottle

1

WAX

1" PVC Tail Adaptor for Electronic Head Bypass

MENU

TSE

90 degree 1" PVC Tail Adaptors also included



CONNECTION SIZE: 1" MAX PRESSURE OPERATING: 80 PSI MAX TEMPERATURE: 100 °DO NOT SCALE DRAWING

THIS DRAWING IS ISSUED IN CONFIDENCE AND CANNOT BE REPRODUCED OR USED TO MANUFACTURE ANYTHING SHOWN OR REFERRED TO WITHOUT DIRECT WRITIEN PERMISSION FROM PELICAN WATER SYSTEMS. P

Pelican Water Systems

3060 PERFORMANCE CR SUITE 2 DELAND, FL 32724

1-877-842-1635wm1. pe l i canwater. com

OPTIONAL BYPASS

HOSE SPIGOTS

MENU

SET

SHUT OFF VALVES

**

** BACKWASH LINE TO BE PLUMBED TO A DRAIN

INSTALLATION DIAGRAM PS48/80


Page 6

Installation Overview

Softener Tank

ElectronicHead

BypassValve

OutgoingWater toHouse

Wall

IncomingWaterSupply

Brine Tank

Safety Valve

Drain Line Barb

MENU

SET

Front View

Top View



Bypass Valve Operation

Notice:

The Bypass Valve on the Electronic Head can be set to Bypass or Service by turning the knobs on the top of the valve. The valves can be difficult to turn by hand until the seals become saturated. Use the supplied Bypass Allen Wrench to turn the knobs if necessary.

IMPORTANT! Do not remove the red clips from the Bypass Valve after connecting to main water supply.


Page 7


Figure 2

If the Red Clips are in the slots (female opening of Electronic Head) remove them. Push the male O-Ring side of the Bypass Valve into the female opening of the Electronic Head. Push the Red Clips back into the slots to tighten.

Softener Tank

ElectronicHead

BypassValve

RedClip

Front View

Pre-InstallationBypass Valve Installation

SERVICE BYPASS

Bypass Allen Wrench


Page 8

InstallationInstall Electronic Head

Figure 3

1. Level the Pelican Softener Tank.

Notice:If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical. The bottom of the tank is round and the boot allows the tank to stand upright.

2. Determine the size and material of your incoming water supply line and choose the appropriatefittings required to connect it to the Bypass Valve.

CAUTION:Do not over-tighten any of the fittings during installation.

3. Remove the grey cap from the top of the Softener tank.4. Screw the Electronic Head onto the tank hand-tight.5. Install the appropriate fittings onto the inlet and outlet, following the labels on the Head.6. Connect the incoming water supply to the fitting on the inlet side of the Bypass Valve.7. Connect the outgoing water supply to the outlet side of the Bypass Valve.8. Firmly press one end of the PVC Tubing Drain Line onto the drain line barb, and secure the other

end of the line to a drain.

IMPORTANT!

• Ensure the PVC Tubing Backwash DrainLine is not submerged and is free of kinks.

• Maximum vertical rise of the backwash lineis 6 feet.

• If incorporating two or more backwashingsystems make sure to keep the drain linesseparate.

MENU

SET Electronic Head

Bypass Valve

Tail Adaptors

Red ClipsDistributor Tube




Page 9

Final Setup and Installation

Figure 4

9. Attach the black Brine Tank hose to the connection on the top of the Electronic Head by removing theblack compression nut. Slide the compression nut over the end of the black tube, fully inserting the BrineLine into the port and tighten the compression nut.

10.Add approximately 160 lbs. of salt pellets to the brine tank. (Example: four 40-pound bags)

11.Add 5 gallons of water to the brine tank.

Softener Tank

ElectronicHead

BypassValve

OutgoingWater toHouse

Wall

IncomingWaterSupply

Brine Tank

Safety Valve

1. Set the Bypass Valve into bypass mode.2. Slowly turn on the main water supply until all pipes are pressurized.3. Slowly open the bypass valves.4. Let the Softener Tank fill completely and then open the bypass valves the rest of the way.5. Check for leaks.6. Plug in the Electronic Head.7. Wax stainless steel tank jacket with wax provided or any other non-abrasive auto wax a minimum

of 1-2 times per year or as needed based on the installed environment.

Complete the Installation

Drain Line Barb

Note: Power Source - For safety reasons the outlet must be protected by a Ground Fault Circuit Interrupter (GFCI).



PS48/PS80 Advantage Series Salt Based Water Softeners— Rev NPage 10

Programming the Electronic HeadNote: Remove protective film from electronic head screen.

Step 1: Setting the Date & Time

MENU

SET

1. Press and hold the MENU button until you hear the beep to unlock.2. Press MENU button.3. Press SET once Date & Time Setting is highlighted.4. Using the UP and DOWN buttons input the correct Date and Time Time pressing SET after each input.5. Once set press the MENU button to return to the main menu.

Step 2: Setting the Hardness

1. Using the DOWN button select Hardness and press SET.2. Using the UP or DOWN buttons input the correct hardness number in grains per gallon (GPG).3. Press SET to confirm.4. Once set press the MENU button to return to the main menu.

Note: If your hardness test results read Parts per Million (PPM) or Milligrams per Liter (Mg/l) you would divide that numberby 17.1 to get Grains Per Gallon (GPG).




Step 3: Performing Manual Regeneration

IMPORTANT!You will need to manually regenerate (Regen Now) your system prior to use. To do so follow the programming below. You will not be able to use water for approximately 2 hours during this process.

Adding the Pelican Logo Sticker1. Peel back plastic to remove it from the tank.

2. Place sticker in the desired location on the tank.

1. Using the DOWN button select Manual Regen and press SET.2. Using the UP or DOWN button select either Regen Now or Regen Tonight.

-Regen Now will start a regeneration process immediately.-Regen Tonight will regenerate the system at the default regeneration time of 2:00 am.

3. Once selected press the SET button to confirm. Gears will make noise and water will start to flow.Allow the system to regenerate for approximately 2 hours.

4. Once complete press the MENU button to return to the main menu.




Troubleshooting

Problem Solution

Water leaking at the top of the tank around the head. You may need to turn the head to tighten it. The tank head is installed hand-tight, do not overtighten the head (just turn it snug).

The tank leans to one side or is not level. If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical. The bottom of the tank is round and the boot allows the tank to stand upright.

The Brine Tank has too much water or is not filling properly.

Check and tighten all fittings on Brine Tank and Electronic Head to ensure air is not getting into the Brine Tank Hose.

The system is backwashing but it is not using up any salt.

If the salt has bridged (too much salt has been added to the tank and it has formed a solid block of salt), shake the Brine tank until the block of salt breaks apart.

UnlevelTank

Boot

UnlevelTank

Boot

LevelTank

UnlevelBoot

!IMPORTANT!Do not use where water is microbiologically unsafe or with water of unknown quality without properdisinfection before or after the filter/softener system.




WarrantyPelican Limited Lifetime Warranty

Pelican Water ("Pelican") warrants to the end user ("customer") that its tanks (13" & smaller), in/out heads, bypass's, fittings, Natursoft media and housings ("Covered Items") will be free from defects in material and workmanship under normal use and service for the life of the system. No warranty is made with respect to defects or damaged due to neglect, misuse, alterations, accident, misapplication, physical damage, installation on water quality outside guidelines for system or damaged caused by fire, acts of God, or freezing.**

Pelican 7 Year Limited Warranty

Pelican Water ("Pelican") warrants to the end user ("customer") that its solid-state electronic heads ("Covered Items") will be free from defects in material and workmanship under normal use and service for a period of 7 years.

Limitations and Responsibilities

Pelican’s obligation to the customer under these warranties shall be limited, at its option, to replacement or repair of Covered Items by these warranties, labor is not covered. Prior to return or repair of Covered Items, the customer must obtain a return goods authorization number from Pelican and at Pelicans option, return the Covered Items freight prepaid. Any Covered Item repaired or replaced under these warranties will be returned prepaid standard freight to the original point of shipment. Expedited freight options are available at customer expense.

No warranty is made with respect to defects or damaged due to neglect, misuse, alterations, accident, misapplication, physical damage, or damaged caused by fire, acts of God, or freezing. These warranties apply only to the original registered owner so long as the owner owns the home in which the unit was originally installed. Customer must register their system with Pelican within 90 days of purchase* in order to obtain a warranty. Warranty will discontinue after the unit is removed from the location where it was originally installed. Warranty begins on the date of delivery of product to the customer. Improper maintenance of system (i.e. not replacing filters or media) on time will be considered "neglect". Installation of any system on water conditions outside of or beyond the recommended specs of any system voids any warranty.

Pelican gives this warranty to the customer in lieu of all other warranties, express or implied, including without limitation any implied warranties of merchantability or fitness for a particular purpose or treatment of certain water and hereby expressly disclaims all other such warranties. Pelican’s liability hereunder shall not exceed the cost of the product. Under no circumstances will Pelican be liable for any incidental or consequential damages or for any other loss, damage or expense of any kind, including loss of use, arising in connection with the installation or use or inability to use the Covered Items or any water treatment system the Covered Items are incorporated into. These warranties are governed by the laws of the state of Florida and may change at any time without notice.

*Failure by California and Quebec residents to complete the product registration form does not diminishtheir warranty rights.

**For all orders placed on or after June 3rd, 2011.




Warranty Registration Form

Send in this Warranty Registration Form to validate your warranty or visitwww.PelicanWater.com to complete warranty registration form online.

Pelican Warranty Registration Form

Send To:

Pelican Water Systems3060 Performance Circle, Suite 2DeLand, FL 32724Phone: (877) 842-1635

Date Item(s) were Received: Order ID#: Model:

Dealer Purchased From:

Name:

Address:

City: State: Zip:

Model/Serial Number:

Plumber’s Information (optional)

We like to recommend good plumbers throughout the USA and if you were happy with your installer please give us their information so we can pass it on as a courtesy. Thank you for your time.

Name of Plumbing Company used to install system: _____________________________________

Phone #: (_____)-__________________ of the Plumbing installer



http://www.PelicanWater.com

— Rev PS48/PS80 Advantage Series Salt Based … Power Source - For safety reasons the outlet must...

Documents

Transcript of — Rev PS48/PS80 Advantage Series Salt Based … Power Source - For safety reasons the outlet must...