Contents · Our UV systems have long been at home in the ... The Filaments and Arc in a ......

Contents

Section 1Intro Corporate Profile Ultra Violet Sterilization Technology UV Inactivation Chart

Section 2Ultra Violet Drinking Water Purification Systems Residential Systems Commercial Systems Integrated Systems Industrial Systems Wastewater Systems Customized Systems 50 - 250 GPM Skid and Rack Mounted Hazardous Area Solar Powered

Section 3Reverse Osmosis Tap Water RO Systems Brackish and Sea Water RO Systems

Section 4Electronics Electronic Ballasts and Monitors Replacement Lamps and Quartz Sleeves

Section 5Filtration Residential / Light Commercial Filtration Systems Pressure Drop Charts Spin-Down Separators Commercial / Industrial Filtration Systems

3 5 10

11 25 41 53 63 67 69 85 87

93 95

9799

103 104 105 107

Copyright Wyckomar Inc. 2012

Partial List of Customers

Wyckomar has configured UV water purification systems for a wide variety of customers including Kellogg Brown & Root (international procurement and engineering firm), The Sable Island Offshore Energy Project (offshore oil/gas drilling platforms in eastern Canada), The US Armed Forces in Bosnia (transportable military grade systems), Canadian Coast Guard (ship-board waste water treatment systems), Cargill Inc., Exxon Mobile, National Beef, Joriki Inc., Silani Sweet Cheese, Tembec, plus a wide variety of distributors, dealers and wholesalers in Canada, US, Australia, Philippines, The Netherlands, New Zealand, China, Singapore, UAE among others.

Corporate Profile

We are pleased to introduce Wyckomar Inc., a Canadian manufacturing company with more than 30 years of experience as a leader in the small systems sector of the global water purification industry. Our company currently exports from our main facility in Guelph, Ontario Canada to more than 40 countries worldwide.

This profile will introduce our company, our products, our markets, our experience and our strengths in the water purification and custom manufacturing sector.

Wyckomar Inc. was founded in 1978 in response to a need for non-chemical technologies to produce safe, clean and pathogen-free drinking water to consumers and businesses around the globe. Our company played a key role in the development of Ultra Violet (UV) drinking water systems for residential and commercial use. Many of Wyckomar's original UV system designs are still in use today.

In the early days, our market penetration was most pronounced in regions of Europe where UV has long enjoyed a well-deserved reputation as a safe and effective, non-chemical water disinfection technology. Our UV systems have long been at home in the shipping industry, on vessels plying European waterways. More recently, our company has opened new domestic and export markets as the popularity of UV technology increases around the world.

Today, Wyckomar manufactures and sells a standard line of UV water purification systems for residential, commercial, industrial, small municipal and specialty applications. We also produce compact "All-In-One" skid mounted and wall mounted water systems for a wide variety of flow rates and applications. "All-In-One" systems are very popular with our customers as they offer a wide variety of filtration, water conditioning and UV disinfection options.

3

The use of UV light to sterilize and disinfect drinking water has a long history of success and is in fact being used in most municipal water treatment plants built in the last 20 years. The invisible rays of UV light are able to produce this very useful effect by mimicking nature. In nature, rays of the sun carry (among others) UV light in the germicidal wavelength of 254 nm. This particular wavelength of light is very damaging to living cells – hence the warnings to reduce human exposure to long periods of high-intensity sunlight – and it's lethal on the microscopic level to living pathogens in drinking water.

Our UV systems are able to provide safe water in regions where the water supply is suspect or in cases where the water supply is contaminated and otherwise unsafe to consume.

The technology is very effective against pathogens including bacterial, viral and protozoa contamination and in many cases can be outfitted to provide safe water even in regions where there is little or no access to electrical service. The use of solar panels to power UV systems has become popular in many parts of the developing world.

The principals of Wyckomar have many decades of combined experience in the water purification industry. Our staff is skilled in all facets of design, fabrication, efficacy validation, sales, customer service and follow-up.

At Wyckomar, we pride ourselves on being a true low-cost, high-quality manufacturer in an industry that is one of the fastest growing in the world. Proper water treatment can make an enormous difference in the quality of life, the quality of commercial and industrial goods and processes, and the quality of business for the distribution agents that we partner with in many regions of the world.

Please contact us with any inquiries.

[email protected]

We Kill Harmful Bacteria and Other Pathogens Including

E. coli CryptosporidiumColiform Giardia

Legionella StaphylococcusCholera MoldAnthrax Poliovirus

Streptococcus HepatitisTuberculosis InfluenzaCoxsackie ShigellaTyphoid Rotavirus

Salmonella AdenovirusCampylobacter Toxoplasma

4

Ultraviolet Sterilization Technology

Ultraviolet disinfection systems are mysterious to many people – how can “light” kill bacteria? But the truth is it can. Ultraviolet (UV) technology has been around for more than 60 years, and its effectiveness has been well documented both scientifically and commercially. It is nature’s own disinfection/purification method. With consumers becoming more concerned about chlorine and other chemical contamination of drinking water, more dealers are prescribing the ultraviolet solution suitable for both small flow residential applications as well as large flow commercial projects.

Ultraviolet is a means of killing or rendering harmless microorganisms in a dedicated environment. These microorganisms can range from bacteria and viruses to algae and protozoa. UV disinfection is used in air and water purification, sewage treatment, protection of food and beverages, and many other disinfection and sterilization applications. A major advantage of UV treatment is that it is considered safer and more reliable for disinfection of water than chemical alternatives, while the level of disinfection is much higher. UV treatment systems are also extremely cost efficient and require less space than alternative disinfection systems.

What is UV and how does it work?

Ultraviolet light is one energy region of the electromagnetic spectrum, which lies between the x-ray region and the visible region. Wavelenghts of visible light range between 400 and 700 nanometers (nm). UV itself lies in the ranges of 200 nm to 390 nm. Optimal UV germicidal action occurs at 254 nm.

Since natural germicidal UV light from the sun is screened out by the earth’s atmosphere, we must look to alternative means of producing UV light. This is accomplished through the conversion of electrical energy in a low-pressure

The ElectromagneticSpectrum

5

mercury vapor “hard glass” quartz lamp. Electrons flow through the ionized mercury vapor between the electrodes of the lamp, which then creates UV light.

As UV light penetrates through the cell wall and cytoplasmic membrane of a microorganism that is in the water while it flows through the unit, it causes a molecular rearrangement of the microorganism’s DNA, which prevents it from reproducing. If the cell cannot reproduce, it is considered dead or “inactivated”.

Dosage

UV dosage is the most critical function of UV disinfection, because the extent of inactivation is proportional to the dose applied to the water. As individual UV lamps emit a set amount of ultraviolet energy, it is important that a system be sized correctly. Flow rates are the determining factor and must not be overstated. Contact time, which is the time the water is within the sterilization chamber, is directly proportional to dosage, which is the amount of energy per unit area (calculated by dividing the output in watts by the surface area of the lamp), and thus the overall effectiveness of microbial destruction in the system. This product of intensity and time is known as the Dose and is expressed in microwatt seconds per centimeter squared (µWsec/cm2). Divide by 1000 to express the dose in the preferred notation mJ/cm2 (milli joule per centimeter squared).

DOSE = time (sec) x output (watts)area (cm2)

For maximum UV transmission a “hard glass” quartz sleeve is recommended for two main reasons. It isolates the lamp from the water to offer more uniform operating temperatures and allows for higher UV output into the water.

Optional Features

A variety of optional features may be added on to the UV sterilizers. They include UV monitoring devices that measure the actual UV output in real time, solenoid shut-off devices that will stop the water flow in

The Filaments and Arc in a UV Lamp

Water flows through the chamber in an upward circular path

6

the event of a system failure, flow control devices to properly limit the water flow in the units, audible and visual alarms (both local and remote) to warn of lamp failures, high temperature sensors to monitor excessive temperatures in the reactor chamber or control panel, and hour meters to monitor the running time of the UV lamps.

Advantages of UV Sterilization

Following are the advantages of UV sterilization: Environmentally friendly, no dangerous or toxic chemicals to handle, no

problem of overdosing (it’s impossible), no need for specialized storage equipment, no WHMIS requirements.

Low initial capital cost as well as reduced operating expenses when compared with similar technologies such as ozone, chlorine, etc.

Immediate treatment process, no need for holding tanks, long retention times, etc.

Extremely economical, hundreds of gallons may be treated for each penny of operating cost.

No chemicals are added to the water supply – no chlorinated by-products are generated (i.e. chlorine + organics = trihalomethanes).

No change in taste, odor, pH or conductivity or the general chemistry of the water, essential minerals and trace elements remain in the water

Automatic operation without special attention or measurement, operator friendly.

Simplicity and ease of maintenance, periodic cleaning (if applicable) and annual lamp replacement, no moving parts to wear out.

Easy installation, only two water connections and a power connection. Compatible with all other water processes (i.e. RO, filtration, ion

exchange, etc.)

Factors Affecting UV

Because UV does not leave any measurable residual in the water, it is recommended that the UV sterilizer be installed as the final step of treatment and located as close as possible to the final distribution system. Once the quality of your water source has been determined, you will need to look at things that can inhibit the UV from functioning properly (e.g., iron, manganese, TDS, turbidity, and suspended solids).

Iron and Manganese will cause staining on the quartz sleeve and prevent the UV light from transmitting into the water at levels as low as 0.3 ppm of iron and 0.05 ppm of manganese. Proper pretreatment is required to eliminate this staining problem.

A solenoid valve shuts off the flow of water, if the intensity of the UV lamp goes down

7

Total Dissolved Solids (TDS) should not exceed 500 ppm. There are many factors that make up this equation such as the particular make-up of the dissolved solids and how fast they absorb on the sleeve, again impeding the UV energy from penetrating the water.

Turbidity is the inability of light to travel through water. Turbidity makes water cloudy and aesthetically unpleasant. In the case of UV, levels over 1 NTU can shield microorganisms from UV light, making the process ineffective.

Suspended Solids need to be reduced to a maximum of 5 microns in size. Larger solids have the potential of harboring or encompassing the micro-organisms and preventing the necessary UV exposure. Pre-filtration is a must on all UV applications to effectively destroy microorganisms to a 99.9% kill rate.

Additional Factors - UV levels fluctuate with temperature levels. The optimal operating temperature of a UV lamp must be below or near 40C (104F). Typically, a quartz sleeve is installed to buffer direct lamp-water contact, thereby reducing any temperature fluctuations. The UV dose applied to the water decreases significantly with temperatures over 40C.

UV Applications

One of the most common uses of ultraviolet sterilization is the disinfection of domestic water supplies due to contaminated wells or surface water sources. Coupled with appropriate pre-treatment equipment, UV provides an economical, efficient and user-friendly means of producing safe potable water.

The following list shows where ultraviolet technology is currently in use:

surface water laboratories bottled water plantsground water wineries pharmaceuticalscisterns dairies mortgage approvalsbreweries farms electronicshospitals hydroponics aquariarestaurants spas boats and RV’svending machines canneries printingcosmetics food products butter processingbakeries distilleries petro chemicalsschools fish hatcheries photographyboiler feed water water softeners swimming poolscooling towers sprinkler systems bottling plantsand much more…

Installation and Maintenance Guidelines

Once the application has been determined, you should find a location that offers easy access for service. You will need to have access to the pre-filters, to the

8

UV chamber for annual lamp changes and regular maintenance on the quartz sleeve. You will want to locate near an electrical outlet. *Note: Using a UV system and a pump on the same electrical line may cause problems and shorten the life of the UV lamp and ballast. A surge protector with a rating of at least 3600 Joules should be installed to protect the electronic ballast from damage due to power spikes or lightning strikes. UV units are installed on the cold water line before any branch lines and should be the last point of treatment. Clearance for lamp change has to be considered during installation. All points of the distribution system after the sterilizer must be chemically “shocked” to ensure that the system is free from any downstream microbial contamination. Lamp changes should be done at least once every year. Filter changes are done according to the condition of the feed water. If there is residue left, you may need to use a non-abrasive cleaner that does not scratch the surface and is formulated to remove iron and scale buildup. Do not leave fingerprints on the glass! It is imperative to follow the manufacturers guidelines on feed water quality and operational procedures.

Summary

The need for ultraviolet sterilization products can be found in virtually all areas in both residential and commercial applications alike. Its simplistic design, ease of maintenance and low capital and operating costs make UV disinfection the number one choice in contaminated water situations. Because of its advantages, UV irradiation is on the way to become the most popular choice for the disinfection of water supplies in the 21st century.

Next time, purify water “natures way”…use ultraviolet light.

Copyright 2012 Wyckomar Inc. UV Purification Systems Although we take great care in producing this catalogue, Wyckomar reserves the right to correct errors and make changes without notice and at anytime.

9

UV Inactivation Chart* (in mJ/cm2)

Typical Wyckomar UV systems produce UV doses of 38 – 60 mJ/cm2

*UV energy levels required at 254 nanometer wavelength for 99.9% (log 3) destruction of organisms

Organism Type Affiliated Disease, Contamination, Toxin Dose log 3 Reference

Adenoviridae Virus Upper respiratory infections (most UV-resisitant virus known) 90 Meng and Gerba, 1996Protist Amoebic keratitis and encephalitis 140 Maya et al, 2003

Aeromonas hydrophila Bacterium Tissue damage in humans (opportunistic pathogen) 3.9 Wilson et al, 1992Agrobacterium tumefaciens Bacterium Crown Gall disease in Dicotyledons (Grapes, Berries, Fruits, Nuts) 8.5

Fungus (Mold Spore) Aspergillosis of the lungs, corneal infections 99.0Fungus (Mold Spore) Allergenic 88.0Fungus (Mold Spore) Otomycosis, Black mold on fruits and vegetables 330.0

Bacillus anthracis Bacterium Anthrax 8.7Bacterium Anthrax 46.2 Pasteur Institute, ParisBacterium Infections, food poisoning 2.5Bacterium Infections, food poisoning 52.0

B. paratyphosus Bacterium non pathogenic 6.1Bacterium Ropiness in bread dough, food contamination 11.0Bacterium Ropiness in bread dough, food contamination 61.0 Chang et al, 1985, Sommer et al, 1998

Campylobacter jejuni Bacterium Food poisoning, gastroenteritis 4.0 Wilson et al, 1992Chlorella vulgaris Protist (algae) Plant pathogen 22.0Clostridium tetani Bacterium Tetanus 23.1 Pasteur Institute, ParisC. botulinum Bacterium Produces Botulin toxin 11.2C. perfringens Bacterium 75.0 Jacangelo et al, 2003Coliphage Virus 6.6Corynebacterium diphtheriae Bacterium Diphtheria 6.5Coxsackie A Virus Hand, foot & mouth disease, conjunctivitis, herpangina 6.9Coxsackie B Virus Pericarditis, myocarditis, gastrointestinal distress 20.6 Battigelli et al, 1993Cryptosporidium parvum Protist Cryptospiridiosis, gastrointestinal illness 25.0 Craik et al, 2001Cyanobacteria Bacterium (blue green algae) 700.0 Masschelein et al, 1989

Bacterium (sulfate-reduction bacteria) Contamination of oilfield process water 10.0 Hagan et al, 2011Eberthella typhosa Bacterium Typhoid fever 4.1Entamoeba histolytica Protist Amoebiasis 84.0Enterococcus spp. Bacterium Indicator species for (recreational) water quality 30.0 Beltran and Jimenez, 2008Escherichia coli Bacterium Food poisoning, gastroenteritis, meiningitis 8.6 Sommer et al, 1998; Wilson et al, 1992Fusarium oxysporum Fungus Plant pathogen (Fusarium wilt) 100.0Giardia lamblia (cysts) Protist Giardiasis (Beaver Fever, Traveller's Diarrhea) 10.0 Linden et al, 2002Hepatitis virus Virus Hepatitis, jaundice 15.0 US.EPA, 1999Influenza virus Virus Influenza, respiratory infections 6.6Klebsiella pneumoniae Bacterium 15.0Legionella bozemanii Bacterium Pneumonia 3.5L. dumoffii Bacterium Pneumonia 5.5L. gormanii Bacterium Pneumonia 4.9L. longbeachae Bacterium Legionnaire's disease, pontiac fever 2.9L. micdadei Bacterium Influenza, Pittsburgh pneumonia 3.1L. pneumophila Bacterium Legionnaire's disease 3.8Leptospira interrogans Bacterium Leptospirosis (Weil's disease, canicola fever, canefield fever, 7-day fever ) 6.0Listeria monocytogenes Bacterium Foodborne Listeriosis 40.0Micrococcus candidus Bacterium 12.3M. sphaeroides Bacterium 15.4Mycobacterium tuberculosis Bacterium Tuberculosis 10.0Mucor racemosus A Fungus (Mold Spore) Fungal plant pathogen, zygomycosis and fungal sinusitis in humans 35.2

Protist Warm water pathogen 105.0Neisseria (Moraxella) catarrhalis Bacterium Otitis media, sinusitis, laryngitis 8.5Nematode eggs (Roundworm) Parasite Ascariasis, Appendicitis, Loeffler’s Syndrome 92.0Oospora lactis Fungus (Mold Spore) Fruit rot (rapid decay of ripe fruits, potatoes), mold in dairy products

Protist 200.0Fungus (Mold Spore) Fungal spoilage in fruits and vegetables 88.0Fungus (Mold Spore) Postharvest decay of stored apples 22.0Fungus (Mold Spore) Producing harmful secondary metabolites (alkaloids and other mycotoxins) 26.4

Phytomonas tumefaciens Bacterium Crown Gall disease in Dicotyledons (Grapes, Berries, Fruits, Nuts) 8.5Polio virus Virus Poliomyelitis (Polio) 29.0 Snicer et al, 1998, Wilson et al, 1992Proteus vulgaris Bacterium Infections (esp. sinus and respiratory, urinary tract) 6.6

Bacterium Hospital acquired infections, ear infection and dermatitis in pools & tubs 3.9Bacterium Hospital acquired infections, ear infection and dermatitis in pools & tubs 10.5Fungus Plant pathogen (root rot) 100.0Fungus (Mold Spore) Infections, allergetic reactions (known as breadmold) 220.0

Rhodospirillum rubrum Bacterium 6.2Rotavirus Virus Infections, severe diahorrea, gastroenteritis 26.0 Battigelli et al., 1993; Wilson et al., 1992

Yeast 13.2Salmonella enteritidis Bacterium Egg-associated Salmonellosis (fever, abdominal cramps, diarrhea) 7.6 Tosa and Hirata, 1998S. paratyphi Bacterium Enteric fever 6.1S. typhi Bacterium Typhoid fever 30.0 Beltran and Jimenez, 2008Sarcina lutea Bacterium 26.4Serratia marcescens Bacterium Nosocomial (Hospital acquired) infections 6.2Shigella dysenteriae Bacterium Epidemic dysentery 4.2 Wilson et al., 1992S. flexneri Bacterium Shigellosis, dysentery 3.4S. sonnei Bacterium Shigellosis 7.0 Chang et al., 1985Staphylococcus aureus Bacterium Staph and nosocomical infections, toxic shock syndrome 7.0 Chang et al., 1986S. epidermidis Bacterium Infections in catheters and prostheses 5.8Streptococcus hemolyticus Bacterium Strep throat 5.5S. faecalis Bacterium Endocarditis, bladder and prostate infection 8.0 Harris et al., 1987S. lactis Bacterium 8.8S.pyogenes Bacterium Scarlet fever, toxic shock syndrome, flesh eating disease 8.8S. viridans Bacterium Mouth or gingivial infections, endocarditis 3.8Tobacco mosaic virus Virus Mottling and discoloration in plants 440.0Toxoplasma gondii Protist Toxoplasmosis 8.0 Linden and Sobsey, EPA 2005Vibrio cholerae Bacterium Cholera 2.2 Wilson et al., 1992Yersinia enterocolitica Bacterium Yersiniosis (fever, abdominal pain, diarrhea 3.7 Wilson et al., 1992

Acanthamoeba spp. (cysts)

Aspergillus flavus (yellow green)A. glaucus (blue green)A. niger (black)

B. anthracis (spores)B. megatherium (vegetable)B. megatherium (spores)

B. subtilis (vegetable)B. subtilis (spores)

Food posoning (ex C. welchii)Bacteriophage that infects E. coli

Desulfovibrio spp

Naegleria fowleri (cyst)

Paramecium spp.Penicillum digitatum (olive)P. expansum (olive)P. roqueforti (green)

Pseudomonas aeruginosa (lab)Pseudomonas aeruginosa (env.)Pythium sppRhizopus nigricans (black)

Saccharomyces spp

10

Residential Water Puri�cation Systems1, 4 & 8 GPM

Basic Models for POU / POEAvailable with or without Pre-Filtration

UV Disinfection for Bacteria / Virus Destruction

SYS2504 GPM / 15 LPMFiltration andUV Disinfection

SYS7008 GPM /30 LPMFiltration andUV Disinfection

SYS11 GPM / 4 LPMPoint-of-Use Filtration and UV Disinfection

UV-7008 GPM / 30 LPMUV Disinfection

11

Description

UV-1Ultra Violet Water Sterilizer

Applications

Benefits

► Potable Water ► RV’s ► Cottages ► RO Systems ► Laboratories► Dental Offices► Water Cooler

► ► ► ► ► ► ►►

The UV-1 is a robust, efficient and cost-effective ultra-violet sterilizer designed for the disinfection of drinking water in the average household at a flow rate of 1 GPM (4 LPM). Typically installed at the point of use (e.g. under the sink), it can treat mu-nicipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. Other applications for this sterilizer are for the purification of process water in laboratories and dental offices, or the prevention of biofouling in RO Systems.

This sterilizer contains a low-pressure, high output UV lamp in a 304L stainless steel reaction chamber (also available in 316L). It comes with an electronic ballast that features a lamp-out alarm if there is no power to the lamp.

Combined with a Wyckomar filter set, this sterilizer is the centre piece of a complete water treatment system for the elimination of bacteria and viruses and reduction of taste and odour at the point of use (see part # SYS1-QD4E-1/2).

Additional features for this sterilizer can be ordered, such as a thermo-sensitive purge valve at the out port to prevent overheating in no-flow conditions, or volt-free contacts on the ballast for remote signaling. A 12 V DC version for use on boats or RVs is also available.

The UV-1 kills most harmful pathogens such as viruses, bacteria and protozoa with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of 99.99% (log 4) or more (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legion-ella, Salmonella, Shigella, Streptococcus and many others)

Dimensions (inches)

Efficient Disinfection, Low Cost per LitreHigh UV Dose for Peace of MindEasy InstallationExtremely Simple to Use and MaintainEasy Lamp ReplacementHigh Quality Stainless Steel Reaction ChamberDomed Quartz Sleeve with Single SealMade in Canada

13

Manufactured in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph, Ontario Canada N1K 1A8Phone ++1-519-822-1886 Fax ++1-519-763-6580 [email protected] www.wyckomaruv.com

Additional Features(Optional):

SpecificationsRated Flow: 4 litres per minute (1 GPM) 240 litres/hour, 5.7 m3/day (60 gallons/hour, 1440 gallons/day)Initial UV Dose at Rated Flow: 63 mJ/cm2 (63,000 μWsec/cm2) @ 95% UVT 43 mJ/cm2 (43,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P1/QD4E-1) 220-240 Volt AC / 50-60 Hz (Part # P1/QD4E-2) 12 V DC (Part # P1/QD4E-12)Power Consumption: 18 VA @ 120 V, 23 VA @ 240 V, 0.7 VA @ 12 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Number of Lamps: 1 at 12 Watts, 425 mA (Part # RL-12/254T5)UV Monitor: NoHour Meter: Optional (Part # 4-HM-R100)Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/8” FNPT In/OutChamber Material: 304L Stainless Steel (316L SS optional)Shipping Size and Weight: 1 box 16x7x4 inches, 5 lbs / 2.3 kg

Electronic Deposit Control System with PVC or Stainless Reaction Chamber

Volt-Free Contacts on Ballast for Remote Signaling

Purge Valve at Out Port for Overheat Protection

Ballast with Hour Meter for Total Runtime Display

Dose Chart

FiltrationThis UV sterilizer assumes certain water quality parameters to be met for proper operation. If the source water does not meet the following criteria, pretreatment has to be considered:Turbidity (Suspended Solids): must be < 1 NTU at the time of disinfection. There must be a 5 micron or less sediment prefiltration system installed before the UV system.Total Hardness (Sum of Calcium and Magnesium): Must be < 10 gpg (grains per gallon)Iron: Must be < 0.3 ppm (parts per million)Manganese: Must be < 0.05 ppm

This UV unit is available as complete system with appropriate pre-filtration (Part # SYS1/QD4E-1/2)

Part # P1/QD4E-1/2

14

Description

Features

BenefitsChemical-Free Disinfection, Low Cost per LitreHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainFully Assembled for Easy InstallationIdeal for Use on Houseboats, RV’s and Condo’s

► ► ►►►

SYS1Water Treatment System

The SYS1 is an All-in-One Water Treatment System that is sized for the needs of the average household to provide purified drinking water at the point of use. Typically installed under the sink, it is used for treating municipal water in apartments and cottages, at laboratories or dental offices. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration in 2 stages down to 0.5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

This purifier comes equipped with an elec-tronic ballast that features an alarm system which sounds an audible alarm if the UV lamp is not functioning properly. The filter housings come with pressure relief valves. A 12 V DC ballast for the use on boats and RVs is also available.

An integrated faucet set is included for the provision of the purified drinking water. All installation hardware (mounting bracket, saddle valves and tubing) are supplied with the system.

This residential water purification system offers very efficient water treatment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.

► Robust Construction ► 304L SS Sterilizer ► Sediment + Carbon Filtration► Electronic Ballast► Lamp-Out Alarm► Self Contained► Energy Efficient

Typical Installation for drinking water under the sink

15



SpecificationsRated Flow: 4 litres per minute (1 GPM) 240 litres/hour, 5.7 m3/day (60 gallons/hour, 1440 gallons/day)Initial UV Dose at Rated Flow: 63 mJ/cm2 (63,000 μWsec/cm2) @ 95% UVT 43 mJ/cm2 (43,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS1/QD4E-1) 220-240 Volt Ac / 50-60 Hz (Part # SYS1/QD4E-2) 12 V DC (Part # SYS1/QD4E-12)Power Consumption: 18 VA @ 120 V, 23 VA @ 240 V, 0.7 VA @ 12 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-12/254T5Filtration: 10” SlimLine (L 9-3/4“, OD 2-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: C-MAX MAX-CYST Bituminous Carbon, 0.5 Micron Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/8” In/Out, comes w/ Saddle Valves & Tubing (PVC)Shipping Size and Weight: 1 box 19x15x7 inches, 15 lbs / 6.8 kg


Additional Filtration for Most Common Contaminants and Pollutants



Pressure Drop Charts

FiltrationThis UV System comes equipped with dual pre-filtration. The water first enters the sediment filter housing, where a sediment filter cartridge (made from melt-blown Polypropylene) removes dirt, rust and other sediments down to 5 micron (cartridge Part # 14-WFS10-5SP). This is followed by a second filter housing with a carbon block filter cartridge at 0.5 micron (made from Coconut Shell Carbon), which removes chlorine, taste and odour from the water (cartridge Part # 14-WFC10-05CB). Additional filtration stages can be installed, such as a self-cleaning Spin Down Separator that keeps the filter cartridges from clogging up if elevated sediment levels are present (Part # 14-WFS-15SC). The filter cartridges are NSF certified and have an excellent chemical resistance in all food and beverage purification applications.

Part # SYS1/QD4E-1/2

The filter cartridges in this system have a great surface area for long life and reduced filtration costs.

Carbon Block FilterSediment Filter

16

Description


Applications

Benefits

► Potable Water ► Whole House (up to 3 People) ► Cottages► Laboratories► Water Dispenser► RO Systems

► ► ► ► ► ► ►►

The UV-250 is a robust, efficient and cost-effective ultra-violet sterilizer designed for the disinfection of drinking water in the average household at a flow rate of 4 GPM (15 LPM). Typically installed at the point of entry, it can treat municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. Other applications for this sterilizer are for the purification of process water in laboratories and dental offices, or for the production of water dispensers.


Combined with a Wyckomar filter set, this sterilizer is the centre piece of a complete water treatment system for the elimination of bacteria and viruses and reduction of taste and odour at the point of entry (see part # SYS250-QD4E-1/2).

Additional features for this sterilizer can be ordered, such as a thermo-sensitive purge valve at the out port to prevent overheating in no-flow conditions, or volt-free contacts on the ballast for remote signaling.

The UV-250 kills most harmful pathogens such as viruses, bacteria and protozoa with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of 99.99% (log 4) or more (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

Dimensions (inches)


17


SpecificationsRated Flow: 15 litres per minute (4 GPM) 900 litres/hour, 21.6 m3/day (240 gallons/hour, 5760 gallons/day)Initial UV Dose at Rated Flow: 46 mJ/cm2 (46,000 μWsec/cm2) @ 95% UVT 32 mJ/cm2 (32,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P250/QD4E-1) 220-240 Volt AC / 50-60 Hz (Part # P250/QD4E-2)Power Consumption: 29 VA @ 120 V, 35 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Number of Lamps: 1 (Part # RL-23/436T5)Lamp Wattage and Current: 23 Watts, 425 mA UV Monitor: Special Order OnlyHour Meter: Optional (Part # 4-HM-R100)Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/4” MNPT In/OutChamber Material: 304L Stainless Steel (316L SS optional)Shipping Size and Weight: 1 box 26x7x6 inches, 8 lbs / 3.6 kg

Part # P250/QD4E-1/2






Available Solar Powered for Use in Off-Grid Applications

Dose Chart


This UV unit is available as complete system with appropriate pre-filtration (Part # SYS250/QD4E-1/2) or as a pre-assembled All-in-One system for ‘plug-and-play” installation (Part # SYS-POU250-1/2)

18

Description

Features

BenefitsEfficient Disinfection, Low Cost per LitreHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainPre-Assembled Filter Set for Easy InstallationIdeal for Use in Households up to 3 People

► ► ►►►


The SYS250 is an All-in-One Water Treat-ment System that is sized for the needs of the smaller household (up to 3 people) to provide complete purified drinking water for domestic use. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

This purifier comes equipped with an electronic ballast that features an alarm system which sounds an audible alarm if the UV lamp is not functioning properly.

All installation hardware (mounting bracket, filter wrench and flexible S-pipe for the connection between filtration and UV) are supplied with the system. Shutoffs are not supplied and are optional, depending on the plumbing set-up.


► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 10” SlimLine Sediment + Carbon Filtration► Filter Housings with Pressure Relief Valves► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm

The system ships complete with all necessary compo-nents and in-stallation hardware

19



SpecificationsRated Flow: 15 litres per minute (4 GPM) 900 litres/hour, 21.6 m3/day (240 gallons/hour, 5,760 gallons/day)Initial UV Dose at Rated Flow: 46 mJ/cm2 (46,000 μWsec/cm2) @ 95% UVT 32 mJ/cm2 (32,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS250/QD4E-1) 220-240 Volt Ac / 50-60 Hz (Part # SYS250/QD4E-2)Power Consumption: 29 VA @ 120 V, 35 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-23/436T5Filtration: 10” SlimLine (L 9-7/8“, OD 2-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Coconut Shell Carbon (Extruded Carbon Block) Connection betw. UV and Filter (S-Pipe): SS Flexible Hose (Part # 10-FF18) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/4” MNPT In/OutShipping Size and Weight: 1 box 26x17x7 inches, 16 lbs / 7.3 kg


Additional Sediment Filtration with Spin Down Separator for Lake Water Applications




FiltrationThis UV System comes equipped with dual pre-filtration. The water first enters the sediment filter housing, where a sediment filter cartridge (made from melt-blown Polypropylene) removes dirt, rust and other sediments down to 5 micron (cartridge Part # 14-WFS10-5SP). This is followed by a second filter housing with a carbon block filter cartridge at 10 micron (made from Coconut Shell Carbon), which removes chlorine, taste and odour from the water (cartridge Part # 14-WFC10-5CB). Additional filtration stages can be installed, such as a self-cleaning Spin Down Separator that keeps the filter cartridges from clogging up if elevated sediment levels are present (Part # 14-WFS-15SC). The filter cartridges are NSF certified and have an excellent chemical resistance in all food and beverage purification applications and a low pressure drop.




20

Description


Applications

Benefits

► Potable Water ► Whole House Water Treatment (up to 6 People) ► Small Commercial Applications, such as Coffee Shops, Doctor’s Offices, Hair Salons► Light Industrial Applications► Food and Beverage Manufacturing

► ► ► ► ► ► ►►

The UV-700 is our best-selling ultra-violet sterilizer designed for the disinfection of drinking water in the average household at a flow rate of 8 GPM (30 LPM). Typically installed at the point of entry, it can treat mu-nicipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. Other applications for this sterilizer are for the purification of all incoming water in various small commercial applications, such as coffee shops, doctor’s offices or hair salons.




The UV-700 kills most harmful pathogens such as viruses, bacteria and protozoa with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of 99.99% (log 4) or more (Giardia, E. coli, Cryptosporidium, Vibria cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).


Dimensions (inches)

21


SpecificationsRated Flow: 30 litres per minute (8 GPM) 1800 litres/hour, 43.2 m3/day (480 gallons/hour, 11520 gallons/day)Initial UV Dose at Rated Flow: 62 mJ/cm2 (62,000 μWsec/cm2) @ 95% UVT 43 mJ/cm2 (43,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P700/QD4E-1) 220-240 Volt AC / 50-60 Hz (Part # P700/QD4E-2)Power Consumption: 53 VA @ 120 V, 66 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Number of Lamps: 1 (Part # RL-40/867T5)Lamp Wattage and Current: 40 Watts, 425 mA UV Monitor: Optional (Part # 4-UV/MS-1/2 V3)Solenoid Valve: Optional (Part # 4-SV-750-1)Hour Meter: Optional (Part # 4-HM-R100)Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/4” MNPT In/OutChamber Material: 304L Stainless Steel (316L SS optional)Shipping Size and Weight: 1 box 45x7x7 inches, 12 lbs / 5.5 kg







Available in Explosion-Proof Configuration

Dose Chart


This UV unit is available as complete system with appropriate pre-filtration (Part # SYS700/QD4E-1/2) or as a pre-assembled All-in-One system for ‘plug-and-play” installation (Part # SYS-MD1003-1/2)

22

Description

Features

BenefitsEfficient Disinfection, Low Cost per LitreHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainPre Assembled Filter Set for Easy InstallationIdeal for Use in Households up to 6 People

► ► ►►►


The SYS700 is an All-in-One Water Treat-ment System that is sized for the needs of the average household (up to 6 people) to provide complete purified drinking water for domestic use. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others)


All installation hardware (mounting bracket, filter wrench and flexible S-pipe for the connection between filtration and UV) are supplied with the system. Shutoffs are not supplied and are optional, depending on the plumbing set-up.


► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 20” SlimLine Sediment + Carbon Filtration► Filter Housings w/ Pressure Relief Valves► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm

The system ships complete with all necessary components and installation hardware

23



SpecificationsRated Flow: 30 litres per minute (8 GPM) 1,800 litres/hour, 43.2 m3/day (480 gallons/hour, 11,520 gallons/day)Initial UV Dose at Rated Flow: 62 mJ/cm2 (62,000 μWsec/cm2) @ 95% UVT 43 mJ/cm2 (43,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS700/QD4E-1) 220-240 Volt Ac / 50-60 Hz (Part # SYS700/QD4E-2)Power Consumption: 53 VA @ 120 V, 66 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-40/867T5Filtration: 20” SlimLine (L 20“, OD 2-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) Connection betw. UV and Filter (S-Pipe): SS Flexible Hose (Part # 10-FF36) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/4” MNPT In/OutShipping Size and Weight: 1 box 45x7x7 inches, 12 lbs / 5.5 kg 1 box 26x17x7 inches, 16 lbs / 7.3 kg






FiltrationThis UV System comes equipped with dual pre-filtration. The water first enters the sediment filter housing, where a sediment filter cartridge (made from melt-blown Polypropylene) removes dirt, rust and other sediments down to 5 micron (cartridge Part # 14-WFS20-5SP). This is followed by a second filter housing with a carbon block filter cartridge at 10 micron (made from Coconut Shell Carbon), which removes chlorine, taste and odour from the water (cartridge Part # 14-WFC20-5CB). Additional filtration stages can be installed, such as a self-cleaning Spin Down Separator that keeps the filter cartridges from clogging up if elevated sediment levels are present (Part # 14-WFS-15SC). The filter cartridges are NSF certified and have an excellent chemical resistance in all food and beverage purification applications and a low pressure drop.




24

UV-3000

UV-5000

UV-120012 GPM / 45 LPM

UV Disinfection30 GPM / 113 LPM

UV Disinfection

UV-1500UV-Monitor

Real Time Monitoringof UV Lamp Power

High VolumeFilter Set 15 GPM / 57 LPM

UV Disinfection

50 GPM / 189 LPM UV Disinfection

Residential/CommercialWater Puri�cation Systems

12, 15, 30 & 50 GPMBasic Models for POE

Available with or without Pre-FiltrationUV Disinfection for Bacteria / Virus Destruction

25

Description


Applications

Benefits

► Potable Water ► Whole House Water Treatment ► Small Commercial Applications► Coffee Shops, Hair Salons ► Doctor’s Offices► Pharmaceutical Manufacturing

► ► ► ► ► ► ►►

The UV-1200 is a robust, high quality ultra-violet sterilizer designed for the disinfection of drinking water in the larger house where there is a 1” line, at a flow rate of 12 GPM (45 LPM). Typically installed at the point of entry, it can treat municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. Other applications for this sterilizer are for the purification of drinking and process water in small commercial applications.




The UV-1200 kills most harmful pathogens such as viruses, bacteria and protozoa with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of 99.99% (log 4) or more (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others). Efficient Disinfection, Low Cost per Litre

High UV Dose for Peace of MindEasy InstallationExtremely Simple to Use and MaintainEasy Lamp ReplacementHigh Quality Stainless Steel Reaction ChamberDomed Quartz Sleeve with Single SealMade in Canada

Dimensions (inches)

27


SpecificationsRated Flow: 45 litres per minute (12 GPM) 2700 litres/hour, 64.8 m3/day (720 gallons/hour, 17,280 gallons/day)Initial UV Dose at Rated Flow: 54 mJ/cm2 (54,000 μWsec/cm2) @ 95% UVT 38 mJ/cm2 (38,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P1200/QD4E-1) 220-240 Volt AC / 50-60 Hz (Part # P1200/QD4E-2)Power Consumption: 70 VA @ 120 V, 84 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL-1/2) w/ Lamp Out Alarm, Power LED Number of Lamps: 1 (Part # RL-84/893T5)Lamp Wattage and Current: 84 Watts, 800 mA UV Monitor: Optional (Part # 4-UV/MS-1/2 V3)Solenoid Valve: Optional (Part # 4-SV-1000-1)Hour Meter: Optional (Part # 4-HM-R100)Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1” MNPT In/OutChamber Material: 304L Stainless Steel (316L SS optional)Shipping Size and Weight: 1 box 45x7x7 inches, 12 lbs / 5.5 kg

Part # P1200/QD4E-1/2






Pre-Assembled and Panel Mounted for Easy Installation

Dose Chart


This UV unit is available as complete system with appropriate pre-filtration (Part # SYS1200/QD4E-1/2) or as a pre-assembled All-in-One system for ‘plug-and-play’ installation (Part # SYS-MD1004-1/2)

28

Description

Features

BenefitsEfficient Disinfection, Low Cost per LitreHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainPre-Assembled Filter Set for Easy InstallationIdeal for Use in Households up to 10 People

► ► ►►►


The SYS1200 is an All-in-One Water Treat-ment System that is sized for the needs of the bigger household (up to 10 people) to provide complete purified drinking water for domestic use. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others)


All installation hardware (mounting brackets, filter wrench and S-pipe for the connection between filtration and UV) are supplied with the system.

This residential/commercial water purifica-tion system offers very efficient water treat-ment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.

► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 20” BigBlue Sediment + Carbon Filtration► Filter Housings with Pressure Relief Valves► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm


29



SpecificationsRated Flow: 45 litres per minute (12 GPM) 2,700 litres/hour, 64.8 m3/day (720 gallons/hour, 17,280 gallons/day)Initial UV Dose at Rated Flow: 54 mJ/cm2 (54,000 μWsec/cm2) @ 95% UVT 38 mJ/cm2 (38,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS1200/QD4E-1) 220-240 Volt AC / 50-60 Hz (Part # SYS1200/QD4E-2)Power Consumption: 70 VA @ 120 V, 84 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL-1/2) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-84/893T5Filtration: 20” BigBlue (L 20“, OD 4-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) Connection betw. UV and Filter (S-Pipe): PVC S-Pipe (Part # 6-1250) (SS Optional) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1” MNPT In/OutShipping Size and Weight: 1 box 45x7x7 inches, 12 lbs / 5.5 kg 1 box 26x17x7 inches, 16 lbs / 7.3 kg






FiltrationThis UV System comes equipped with dual pre-filtration. The water first enters the sediment filter housing, where a sediment filter cartridge (made from melt-blown Polypropylene) removes dirt, rust and other sediments down to 5 micron (cartridge Part # 14-WFS20BB-5SP). This is followed by a second filter housing with a carbon block filter cartridge at 10 micron (made from Coconut Shell Carbon), which removes chlorine, taste and odour from the water (cartridge Part # 14-WFC20BB-5CB). The filter cartridges are NSF certified and have an excellent chemical resistance in all food and beverage purification applications and a low pressure drop.Additional filtration stages can be installed, such as a self-cleaning Spin Down Separator that keeps the filter cartridges from clogging up if elevated sediment levels are present (Part # 13-SDF-2).




30

Description


Applications

Benefits

► Potable Water, Process Water► Commercial and Light Industrial Applications► Pharmaceutical Manufacturing ► Butcher Shops ► Hotels and Restaurants► Pools and Spa’s► Food and Beverage Processing

► ► ► ► ► ►

The UV-1500 is a robust, high quality ultra-violet sterilizer that offers very efficient treatment at a low cost per unit volume. Typically installed at the point of entry, it can treat municipal water as well as ground water from drilled or dug wells, or surface water from lakes, ponds or rivers (pre-filtration necessary). This sterilizer is perfectly sized to provide drinking water or purified process water for large houses and mansions, as well as for commercial and light industrial applications.

The UV-1500 contains a low-pressure, high output UV lamp in a 304L stainless steel reaction chamber (316L available). It comes with an electronic ballast that features a lamp-out alarm if there is no power to the lamp.

Combined with appropriate pre-filtration, this sterilizer is the centre piece of a complete water treatment system for the elimination of bacteria and viruses and reduction of taste and odour at the point of entry.

Additional features for this sterilizer can be ordered, such as a UV-monitoring system for fail-safe operation, a thermo-sensitive purge valve at the out port to prevent over-heating in no-flow conditions, or volt-free contacts on the ballasts for remote signal-ing.


Exceptional High UV DoseExtremely Simple to Use and MaintainHigh Quality Stainless Steel Reaction ChamberEasily Upgradeable with Optional FeaturesMade in Canada

Dimensions (inches)

31


SpecificationsRated Flow: 57 litres per minute (15 GPM) 3420 litres (3.4 m3)/hour, 82 m3/day (900 gallons/hour, 21,600 gallons/day)Initial UV Dose at Rated Flow: 42 mJ/cm2 (42,000 μWsec/cm2) @ 95% UVT 27 mJ/cm2 (27,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P1500/QS4E-1) 220-240 Volt AC / 50-60 Hz (Part # P1500/QS4E-2)Power Consumption: 102 VA @ 120 V, 107 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL-1/2) w/ Lamp Out Alarm, Power LED Number of Lamps: 1 (Part # RL-110/1197T5)Lamp Wattage and Current: 110 Watts, 800 mA UV Monitor: Optional (Part # 4-UV/MS-1/2 V3)Solenoid Valve: Optional (Part # 4-SV-1000-1)Hour Meter: Optional (Part # 4-HM-R100) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1” MNPT In/OutChamber Material: 304L Stainless Steel (316L optional)Shipping Size and Weight: 1 box 52x9x9 inches, 17 lbs / 7.8 kg

Part # P1500/QS4E-1/2






Rack- or Skid-Mounted for Easy Installation

Dose Chart


This UV unit is available as complete system with appropriate pre-filtration (Part # SYS1500/QS4E-1/2) and can be customized for many applications with pre-filtration into All-in-One rack mounted systems.

32

Description

Features

BenefitsEfficient Disinfection, Low Cost per LitreHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainPre-Assembled Filter Set for Easy InstallationIdeal for Use in Light Commercial Applications

► ► ►►►


The SYS1500 is an All-in-One Water Treat-ment System that is sized for the needs of the bigger household to provide complete purified drinking water for domestic use. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others)


All installation hardware (mounting brack-ets, filter wrench and S-pipe for the connec-tion between filtration and UV) are supplied with the system.

This residential/commercial water purifica-tion system offers very efficient water treat-ment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.

► Chemical-Free Water Treatment► Robust Construction ► 20” BigBlue Sediment + Carbon Filtration► Filter Housings with Pressure Relief Valves ► 304L SS Ultra-Violet Sterilizer (316L optional)► Electronic Ballast with Lamp-Out Alarm


33



SpecificationsRated Flow: 57 litres per minute (15 GPM) 3,420 litres/hour, 82 m3/day (900 gallons/hour, 21,600 gallons/day)Initial UV Dose at Rated Flow: 42 mJ/cm2 (42,000 μWsec/cm2) @ 95% UVT 27 mJ/cm2 (27,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS1500/QD4E-1) 220-240 Volt Ac / 50-60 Hz (Part # SYS1500/QD4E-2)Power Consumption: 102 VA @ 120 V, 107 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL-1/2) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-110/1197T5Filtration: 20” BigBlue (L 20“, OD 4-1/2”) w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) Connection betw. UV and Filter (S-Pipe): PVC S-Pipe (Part # 6-1500) (SS Optional) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1” MNPT In/OutShipping Size and Weight: 1 box 52x9x9 inches, 17 lbs / 7.7 kg 1 box 26x17x7 inches, 16 lbs / 7.3 kg






FiltrationThis UV System comes equipped with dual pre-filtration. The water first enters the sediment filter housing, where a sediment filter cartridge (made from melt-blown Polypropylene) removes dirt, rust and other sediments down to 5 micron (cartridge Part # 14-WFS20BB-5SP). This is followed by a second filter housing with a carbon block filter cartridge at 10 micron (made from Coconut Shell Carbon), which removes chlorine, taste and odour from the water (cartridge Part # 14-WFC20BB-5CB). The filter cartridges are NSF certified and have an excellent chemical resistance in all food and beverage purification applications and a low pressure drop.Additional filtration stages can be installed, such as a self-cleaning Spin Down Separator that keeps the filter cartridges from clogging up if elevated sediment levels are present (Part # 13-SDF-2).

Part # SYS1500/QS4E-1/2



34

Description


Applications

Benefits

► Potable Water, Process Water► Many Different Commercial Applications ► Health Clinics and Hospital Areas ► Herbal Medicine Production ► Hotels and Restaurants► Fish Farming► Pools and Spa’s► Food and Beverage Processing ► Campgrounds, Trailer Parks

► ► ► ► ► ►

The UV-3000 is a robust, high quality ultra-violet sterilizer that offers very efficient treatment at a low cost per unit volume. Typically installed at the point of entry, it can treat municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers (pre-filtration necessary). This sterilizer is perfectly sized to provide drinking water or purified process water for large houses and mansions, as well as for commercial and light industrial applications.

The UV-3000 contains a low-pressure, high output UV lamp in a 304L stainless steel reaction chamber (316L available). It comes with an electronic ballast that features a lamp-out alarm if there is no power to the lamp.

Combined with appropriate pre-filtration, this sterilizer is the centre piece of a complete water treatment system for the elimination of bacteria and viruses and reduction of taste and odour at the point of entry (see part # SYS3000-QS4E-1/2).



Exceptional High UV DoseExtremely Simple to Use and MaintainHigh Quality Stainless Steel Reaction ChamberEasily Upgradeable with Optional FeaturesMade in Canada

Dimensions (inches)

35


SpecificationsRated Flow: 113 litres per minute (30 GPM) 6780 litres (6.8 m3)/hour, 162 m3/day (1,800 gallons/hour, 43,200 gallons/day)Initial UV Dose at Rated Flow: 49 mJ/cm2 (49,000 μWsec/cm2) @ 95% UVT 34 mJ/cm2 (34,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P3000/QS4E-1) 220-240 Volt AC / 50-60 Hz (Part # P3000/QS4E-2)Power Consumption: 85 VA @ 120 V, 89 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL30-1/2) w/ Lamp Out Alarm, Power LED Number of Lamps: 1 (Part # RL-100/1197T6)Lamp Wattage and Current: 100 Watts, 800 mA UV Monitor: Optional (Part # 4-UV/MS-1/2 V3 )Solenoid Valve: Optional (part # 4-SV-1500-1)Hour Meter: Optional (Part # 4-HM-R100) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1.5” MNPT In/OutChamber Material: 304L Stainless Steel (316L optional) (PVC available)Shipping Size and Weight: 1 box 52x9x9 inches, 24 lbs / 11 kg

Part # P3000/QS4E-1/2






Panel- or Rack-Mounted for Easy Installation

Dose Chart


This UV unit can be manifolded in parallel for higher flow rates and can be customized for many appli-cations with pre-filtration into All-in-One panel-mounted systems (Part # SYS-MD1006-1/2)

36

Description

Features

BenefitsEfficient Disinfection, Low Cost per LitreHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainPre-Assembled Filter Set for Easy InstallationIdeal for Use in Many Commercial Applications

► ► ►►►


The SYS3000 is an All-in-One Water Treat-ment System that is sized for the needs of commercial and light industrial applications to provide complete purified drinking or pro-cess water. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others)


All installation hardware (mounting brack-ets, filter wrench and S-pipe for the connec-tion between filtration and UV) are supplied with the system.

This commercial/industrial water purifica-tion system offers very efficient water treat-ment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.

► Chemical-Free Water Treatment► Robust Construction► 20” BigBlue Sediment + Carbon Filtration► Filter Housings with Pressure Relief Valves► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm


37



SpecificationsRated Flow: 113 litres per minute (30 GPM) 6,780 litres/hour, 162 m3/day (1,800 gallons/hour, 43,200 gallons/day)Initial UV Dose at Rated Flow: 49 mJ/cm2 (49,000 μWsec/cm2) @ 95% UVT 34 mJ/cm2 (34,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS3000/QD4E-1) 220-240 Volt AC / 50-60 Hz (Part # SYS3000/QD4E-2)Power Consumption: 85 VA @ 120 V, 89 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL30-1/2) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-100/1197T6Filtration: 20” BigBlue (L 20“, OD 4-1/2”), w/Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Pleated Carbon NCP Series, 10 Micron Connection betw. UV and Filter (S-Pipe): PVC S-Pipe (Part # 6-3000) (SS Optional) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1.5” MNPT In/OutShipping Size and Weight: 1 box 52x9x9 inches, 24 lbs / 10.9 kg 1 box 26x17x7 inches, 16 lbs / 7.3 kg


Additional Sediment Filtration with Spin Down Separator for High Turbidity Applications



Pressure Gauges


FiltrationThis UV System comes equipped with dual pre-filtration. The water first enters the sediment filter housing, where a sediment filter cartridge (made from melt-blown Polypropylene) removes dirt, rust and other sediments down to 5 micron (cartridge Part # 14-WFS20BB-5SP). This is followed by a second filter housing with a pleated carbon filter cartridge at 10 micron (made from Carbon-impregnated Polyester), which removes chlorine, taste and odour from the water (cartridge Part # 14-WFC20BB-10PLC). The filter cartridges are NSF certified and have an excellent chemical resis-tance in all food and beverage purification applications and a low pressure drop.Additional filtration stages can be installed, such as a self-cleaning Spin Down Separator that keeps the filter cartridges from clogging up if elevated sediment levels are present (Part # 13-SDF-2).

Part # SYS3000/QS4E-1/2


Pleated CarbonSediment Filter

38

Description


Applications

Benefits

► Potable Water, Process Water► Water Bottling Plants ► Food Processing and Packaging Centres ► Hospitals and Health Clinics► Vegetable Processors Irrigation Systems► Pools and Spa’s► Beverage Production

► ► ► ► ► ►

The UV-5000 is a robust, high quality ultra-violet sterilizer that offers very efficient treatment at a low cost per unit volume. Typically installed at the point of entry, it can treat municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers (pre-filtration necessary). This sterilizer is perfectly sized to provide drinking water or purified process water for commercial and light industrial applications, including food and beverage processing, pharmaceutical manufacturing, or cooling towers. It is also a very popular system for the disinfection of pools and spa’s.

The UV-5000 contains two low-pressure, high output UV lamps in a manifolded 316L stainless steel reaction chamber. It comes with two electronic ballasts that feature a lamp-out alarm if there is no power to the lamp.

Combined with appropriate pre-filtration, this sterilizer is the centre piece of a complete water treatment system for the elimination of bacteria and viruses and reduction of taste and odour at the point of entry.


The UV-5000 kills most harmful pathogens such as viruses, bacteria and protozoa with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of 99.99% (log 4) or more (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

Efficient Disinfection, Low Cost per LitreExceptional High UV DoseExtremely Simple to Use and MaintainHigh Quality Stainless Steel Reaction ChamberEasily Upgradeable with Optional FeaturesMade in Canada

Dimensions (inches)

39


SpecificationsRated Flow: 189 litres per minute (50 GPM) 11,340 litres (11.3 m3)/hour, 272 m3/day (3,000 gallons/hour, 72,000 gallons/day)Initial UV Dose at Rated Flow: 47 mJ/cm2 (47,000 μWsec/cm2) @ 95% UVT 34 mJ/cm2 (34,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P5000/QS4E-1) 220-240 Volt AC / 50-60 Hz (Part # P5000/QS4E-2)Power Consumption Overall: 204 VA @ 120 V, 214 VA @ 240 VBallast: 2 x Electronic Ballast (Part # 4-BE-800WL-1/2) w/ Lamp Out Alarm, Power LED Number of Lamps: 2 (Part # RL-110/1197T5)Lamp Wattage and Current: 110 Watts, 800 mA UV Monitor: Optional (Part # 4-UV/MS50-1/2 V3)Solenoid Valve: Optional (Part # 4-SV-2000-1)Hour Meter: Optional (Part # 4-HM-R100) (one each per lamp)Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 2” MNPT In/OutChamber Material: 316L Stainless SteelShipping Size and Weight: 1 box 52x16x9 inches, 46 lbs / 21 kg

Part # P5000/QS4E-1/2



Volt-Free Contacts on Ballasts for Remote Signaling


Ballasts with Hour Meter for Total Runtime Display

Rack-Mounted or Skid-Mountedfor Easy Installation

Dose Chart


This UV unit can be manifolded in parallel for higher flow rates (see Part # SYS5100F, SYS5100F3) and can be customized for many applications with pre-filtration into All-in-One rack-mounted systems

40

Integrated Water Puri�cation Systems4 GPM to 30 GPM

All-in-One Treatment with Multiple Filtration LevelsUV Disinfection for Bacteria / Virus Destruction

Optional Monitor, Solenoid Valve, Electronic Fluid ConditioningPre-Assembled Systems, Easy to Install and Maintain

SYS-POU-7008 GPM / 30 LPM

SYS-MD100412 GPM / 45 LPM

SYS-POU2504 GPM / 15 LPM

SYS-MD1006 30 GPM / 113 LPM

41

Integrated Water Purification Systems

Pre-Assembled Units for Plug-and-Play

The Wyckomar Integrated Water Treatment Systems are ideal for residential, commercial and industrial applications where an all-in-one solution to a complex treatment problem is needed. Pre-assembly and pressure testing at the factory ensure that the systems are optimized for the treatment of the particular feed water and will work right out of the box.

These systems can be customized to remove almost any contamination that is in the water, from heavy metals (iron, manganese, arsenic among others) to VOC’s, pesticides and, of course, all types of microorganisms. The rugged design of the systems will ensure many years of faithful service.

The picture shows some of the standard and optional features that can be installed with an integrated system: Standard components: 2 – Sediment Filter, usually down to 5 Micron. 3 – Carbon Block Filter for taste and odour. 8 – UV Sterilizer. 12 – Electronic Ballast. 14 – Viewport. 15 – Power Cord. 16 – Panel (SS) Optional components: 1 and 13 – Shutoff Valves (PVC or Stainless Steel). 4 – Electronic Deposit Control, Reaction Chamber. 5 – Solenoid Valve. 6 – Union. 7 – Drain. 9 – Surge Protector Power Pack. 10 – UV Monitor. 11 – Electronic Deposit Control, Control Panel.

42

Description

Features

BenefitsSafe Drinking Water at Low CostHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainFully Assembled for Easy InstallationIdeal for Use in CottagesMade in Canada

► ► ►►► ►

SYS-POU250All-in-One Water Treatment System

The SYS-POU250 is an All-in-One Water Treatment System that is sized for the needs of the average household (up to 3 people) or cottage to provide complete purified drinking water for domestic use. Typically installed at the point of use, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).


All components of this system are pressure-tested and pre-assembled on a stainless steel panel. It is easy to install and maintain and can be upgraded with optional components for many different water treatment applications.

This residential water purification system offers very efficient water treatment at a low cost per unit volume.

► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 304L SS Ultra-Violet Sterilizer ► Electronic Ballast with Lamp-Out Alarm► 10” SlimLine Filtration in 2 Stages► Filter Housings with Pressure Relief Valves► Many Optional Components► Mounted on Stainless Steel Panel

43


Optional Features

SpecificationsRated Flow: 15 litres per minute (4 GPM) 900 litres/hour, 21.6 m3/day (240 gallons/hour, 5,760 gallons/day)Initial UV Dose at Rated Flow: 46 mJ/cm2 (46,000 μWsec/cm2) @ 95% UVT 32 mJ/cm2 (32,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS-POU250-1) 220-240 Volt Ac / 50-60 Hz (Part # SYS-POU250-2)Power Consumption (Standard Config.): 29 VA @ 120 V, 35 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-23/436T5Filtration: 10” SlimLine (L 9-3/4“, OD 2-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) for High Chlorine ReductionMax. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/4” MNPT In/OutShipping Size and Weight: 1 box. 24x20x9 inches, 25 lbs / 11.4 kg

This system comes by default with filtration and ultra-violet disinfection for the treatment of drinking water from many sources. Additional features can easily be added to make it into a customized water purification system for any kind of application and for the removal/reduction of almost any kind of contaminant.

Hardness - This system works well in coopera-tion with a commercial style softener, but for those applications where salt is not wanted, an electronic scale deposit controller can be added to the panel. The device will condition the calcium and magne-sium molecules, preventing lime build-up in plumbing and appliances.

Monitoring System - For those applications that require fail-safe operation, a monitoring system can be added. This consists of a sensor that measures the intensity of the UV light in real-time, and displays it on a meter face on the moni-tor. In case the intensity goes below the recom-mended dosage for drinking water, the monitor can trigger a solenoid valve to shut off the flow of water until the problem has been rectified.

Special Filtration - If other contaminants are present, such as Arsenic, Fluoride, Nitrate or other pollutants, or if the pH needs to be adjusted, addi-tional filtration levels can easily be added to this system.

Plug & PlayThis Integrated UV System is pre-assembled and pressure tested at the factory and will work right out of the box. The sturdy stainless-steel construction and the attractive panel-mounted design allows for easy installation and ensures many years of faithful service. All components are placed so they can be easily maintained and cleaned.

Part # SYS-POU250-1/2

UV Monitor(Part # 4-UV/MS-1/2 V3)

44

Description

Features

BenefitsSafe Drinking Water at Low CostHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainFully Assembled for Easy InstallationIdeal for Use in Homes and CottagesMade in Canada

► ► ►►► ►

SYS-POU700All-in-One Water Treatment System

The model SYS-POU700 is an All-in-One Water Treatment System that is sized for the needs of the average household (up to 6 people) or cottage to provide complete purified drinking water for domestic use. This system is also popular for small com-mercial use as well, installed at the point of use.

The system treats municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful micro-organisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

The purifier comes equipped with an electronic ballast that features an alarm system which sounds an audible alarm if the UV lamp is not functioning properly.


This water purification system offers very efficient water treatment at a low cost per unit volume.

► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm► 20” SlimLine Filtration in 2 Stages► Filter Housings with Pressure Relief Valves► Many Optional Components► Mounted on Stainless Steel Panel

45


Optional Features

SpecificationsRated Flow: 30 litres per minute (8 GPM) 1,800 litres/hour, 43.2 m3/day (480 gallons/hour, 11,520 gallons/day)Initial UV Dose at Rated Flow: 62 mJ/cm2 (62,000 μWsec/cm2) @ 95% UVT 43 mJ/cm2 (43,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS-POU700-1) 220-240 Volt AC / 50-60 Hz (Part # SYS-POU700-2)Power Consumption (Standard Config.): 53 VA @ 120 V, 66 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-40/867T5Filtration: 20” SlimLine (L 20“, OD 2-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) for High Chlorine ReductionMax. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/4” MNPT In/OutShipping Size and Weight: 1 box. 40x20x7 inches, 38 lbs / 17.2 kg





Plug & PlayThis Integrated UV System is pre-assembled and pressure tested at the factory and will work right out of the box. The sturdy stainless-steel construction and the attractive panel-mounted design allows for easy installation and ensures many years of faithful service. All components are placed so they can be easily maintained and cleaned.

Part # SYS-POU700-1/2


46

Description

Features

BenefitsSafe Drinking Water at Low CostHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainFully Assembled for Easy InstallationIdeal for Use in Households up to 6 People

► ► ►►►

SYS-MD1003All-in-One Water Treatment System

The SYS-MD1003 is an All-in-One Water Treatment System that is sized for the needs of the average household (up to 6 people) or small commercial application to provide complete purified drinking water for domestic use. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).



This residential/commercial water purifica-tion system offers very efficient water treatment at a low cost per unit volume.

► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm► 20” SlimLine Filtration in 3 Stages► Pressure Gauges (not shown)

► Manual Shutoffs ► Many Optional Components► Mounted on Stainless Steel Panel► Self Contained, Energy Efficient

Pictured System with Electronic Descaler. Configurations may vary.

47


Optional Features

SpecificationsRated Flow: 30 litres per minute (8 GPM) 1,800 litres/hour, 43.2 m3/day (480 gallons/hour, 11,520 gallons/day)Initial UV Dose at Rated Flow: 62 mJ/cm2 (62,000 μWsec/cm2) @ 95% UVT 43 mJ/cm2 (43,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS-MD1003-1) 220-240 Volt Ac / 50-60 Hz (Part # SYS-MD1003-2)Power Consumption (Standard Config.): 53 VA @ 120 V, 66 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-425W-U) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-40/867T5Filtration: 20” SlimLine (L 20“, OD 2-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Granular Activated Carbon (”GAC”), Coconut Shell Stage 3, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3/4” MNPT In/OutShipping Size and Weight: 1 Skid approx. 45x38x32 inches, 95 lbs / 43.2 kg





Plug & PlayThis Integrated UV System is pre-assembled and pressure tested at the factory and will work right out of the box. The sturdy stainless-steel construction and the attractive, panel-mounted design allows for easy installation and ensures many years of faithful service. All components are placed so they can be easily maintained and cleaned. Manual shutoff valves on the In and Out port allow for simple plumbing and make it easy to install a bypass.

Part # SYS-MD1003-1/2


48

Description

Features

BenefitsSafe Drinking Water at Low CostHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainFully Assembled for Easy InstallationIdeal for Use in Households up to 10 People

► ► ►►►


The SYS-MD1004 is an All-in-One Water Treatment System that is sized for the needs of the bigger household (up to 10 people) or small to medium commercial application to provide complete purified drinking water for domestic use. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).


All components of this system are pressure-tested and pre-assembled on a stainless steel panel. It is easy to install and maintain and can be upgraded with various optional components for many different water treatment applications.


► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm► 20” BigBlue Filtration in 3 Stages► Pressure Gauges► Manual Shutoffs ► Many Optional Components► Mounted on Stainless Steel Panel► Self Contained, Energy Efficient

Pictured System with Electronic Descaler, Monitor and Solenoid Valve

49


Optional Features

SpecificationsRated Flow: 45 litres per minute (12 GPM) 2,700 litres/hour, 64.8 m3/day (720 gallons/hour, 17,280 gallons/day)Initial UV Dose at Rated Flow: 54 mJ/cm2 (54,000 μWsec/cm2) @ 95% UVT 38 mJ/cm2 (38,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS-MD1004-1) 220-240 Volt Ac / 50-60 Hz (Part # SYS-MD1004-2)Power Consumption (Standard Config.): 70 VA @ 120 V, 84 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL-1/2) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-84/893T5Filtration: 20” BigBlue (L 20“, OD 4-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Granular Activated Carbon (”GAC”), Coconut Shell Stage 3, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1” MNPT In/OutShipping Size and Weight: 1 Skid approx. 45x38x32 inches, 95 lbs / 43.2 kg




Special Filtration - If other contaminants are present, such as Arsenic, Fluoride, Nitrate or other pollutants, or if the pH needs to be adjustedd, addi-tional filtration levels can easily be added to this system.

Plug & PlayThis Integrated UV System is pre-assembled and pressure tested at the factory and will work right out of the box. The attractive, panel-mounted design allows for easy installation and ensures many years of faithful service. All components are placed so they can be easily maintained and cleaned. Manual shutoff valves on the In and Out port allow for proper plumbing and make it easy to install a bypass.



50

Description

Features

BenefitsSafe Drinking Water at Low CostHigh UV Dose for Peace of MindExtremely Simple to Use and MaintainFully Assembled for Easy InstallationMade in Canada

► ► ►►►


The SYS-MD1006 is an All-in-One Water Treatment System that is sized for the needs of many commercial and light industrial applications to provide complete purified drinking or process water. Typically installed at the point of entry, it is used for treating municipal water as well as ground water from drilled or dug wells, and surface water from lakes, ponds or rivers. It will purify the water from most contaminants such as sediments, rust and pesticides with filtration down to 5 micron. Carbon filtration reduces taste and odour, including sulphur smell and chlorine residuals, as well as cysts. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of > 99.99% (log4) (Giardia, E. coli, Cryp-tosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).


All components of this system are pressure-tested and pre-assembled on a stainless steel panel. It is easy to install and maintain and can be upgraded with many optional components for many different water treatment applications.


► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► 304L SS Ultra-Violet Sterilizer (316L optional) ► Electronic Ballast with Lamp-Out Alarm► 20” BigBlue Filtration in 2 Stages► Filter Housings with Pressure Relief Valves► Pressure Gauges► Manual Shutoffs ► Many Optional Components► Mounted on Stainless Steel Panel► Self Contained, Energy Efficient

Pictured System with Electronic Descaler, Monitor and Solenoid Valve

51


Optional Features

SpecificationsRated Flow: 113 litres per minute (30 GPM) 6,780 litres/hour, 162 m3/day (1,800 gallons/hour, 43,200 gallons/day)Initial UV Dose at Rated Flow: 49 mJ/cm2 (49,000 μWsec/cm2) @ 95% UVT 34 mJ/cm2 (34,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # SYS-MD1006-1) 220-240 Volt A / 50-60 Hz (Part # SYS-MD1006-2)Power Consumption (Standard Config.): 85 VA @ 120 V, 89 VA @ 240 VBallast: Electronic Ballast (Part # 4-BE-800WL30-1/2) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-100/1197T6Filtration: 20” BigBlue (L 20“, OD 4-1/2”), w/Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Pleated Carbon NCP series, 10 Micron Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 1.5” MNPT In/OutShipping Size and Weight: 1 Skid approx. 52x45x32 inches, 120 lbs / 54.5 kg




Special Filtration - If other contaminants are present, such as Arsenic, Fluoride, Nitrate or other pollutants, or if the pH needs to be adjustedd, addi-tional filtration levels can easily be added to this system.

Plug & PlayThis Integrated UV System is pre-assembled and pressure tested at the factory and will work right out of the box. The attractive, panel-mounted design allows for easy installation and ensures many years of faithful service. All components are placed so they can be easily maintained and cleaned. Manual shutoff valves on the In and Out port allow for proper plumbing and make it easy to install a bypass.


UV Monitor (Part # 4-UV/MS-1/2 V3)

52

Industrial Water Puri�cation Systems100 & 220 GPM

up to 1000 GPM in ManifoldPowerful UV Disinfection for High Volume Applications

UV Disinfection for Bacteria / Virus Destruction

UV-5007 220 GPM / 833 LPM

OptionalSkid Mount

UV-100 100 GPM / 379 LPM SYS5100F100 GPM / 379 LPMEconomical UV

High UV Dose, Small Footprint

Manifold for Higher Flowrates

53

Description

SYS-5100FUltra Violet Water Sterilizer

Applications

Benefits

► Potable Water, Process Water► Water Bottling Plants ► Food Processing and Packaging Centres ► Hospitals and Health Clinics► Vegetable Processors and Irrigation Systems► Rainwater Harvesting► Beverage Production

► ► ► ► ► ►

The SYS-5100F is a robust, high quality and economical ultra-violet sterilizer that offers very efficient treatment at a very low cost per unit volume. Typically installed as a component in a larger water treatment system, it can be used in all applications where safe drinking water is required. In process water applications such as rainwater harvesting, fish farming or irrigation water disinfection, this sterilizer is perfect for the reduction of harmful organisms such as viruses, fungi and protists due to its exceptinal high UV efficacy, as well as in other commercial and industrial applications, including food and beverage processing, pharmaceutical manufacturing, or cooling towers.

The system contains four low-pressure, high output UV lamps in manifolded 316L stainless steel reaction chambers. It comes with electronic ballasts that feature a lamp- out alarm if there is no power to the lamp.


The SYS-5100F kills most harmful pathogens such as viruses, bacteria and protozoa with a powerful UV disinfection dose that will inactivate the organisms at a kill rate of 99.99% (log 4) or more (Giardia, E. coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

Efficient Disinfection, Low Cost per LitreExceptional High UV DoseExtremely Simple to Use and MaintainHigh Quality Stainless Steel Reaction ChamberEasily Upgradeable with Optional FeaturesMade in Canada

Dimensions (inches)

Similar to imageConfigurations may vary

55


SpecificationsRated Flow: 379 litres per minute (100 GPM) 22,740 litres (22.7 m3)/hour, 546 m3/day (6,000 gallons/hour, 144,000 gallons/day)Initial UV Dose at Rated Flow: 47 mJ/cm2 (47,000 μWsec/cm2) @ 95% UVT 34 mJ/cm2 (34,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz, or 220-240 Volt AC / 50-60 Hz Power Consumption Overall: 408 VA @ 120 V, 428 VA @ 240 VBallast: 4 x Electronic Ballast (Part # 4-BE-800WL-1/2) w/ Lamp Out Alarm, Power LED Number of Lamps: 4 (Part # RL-110/1197T5)Lamp Wattage and Current: 110 Watts, 800 mA UV Monitor: Optional (2 x Part # 4-UV/MS50-1/2 V3)Solenoid Valve: Optional (Part # 4-SV-2000-1)Hour Meter: Optional (Part # 4-HM-R100) (one each per lamp)Max. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3” MNPT In/Out (Flanges Optional)Chamber Material: 316L Stainless SteelShipping Size and Weight: 1 skid 24x33x56 inches, 210 lbs

Part # SYS-5100F


UV Monitoring System and Solenoid Valve for Failsafe Operation

Volt-Free Contacts on Ballasts for Remote Signaling


Ballasts with Hour Meter for Total Runtime Display

Sanitary Tubing and Fittings

Dose Chart


This UV unit can be manifolded in parallel for higher flow rates (see Part #SYS5100F3) and can be customized for many applications with pre-filtration into All-in-One skid-mounted systems

56

Description

UV-100 SystemUltra Violet Water Sterilizer

The UV-100 System is a small footprint, robust, efficient and cost-effective sterilizer designed for the disinfection of drinking and/or process water in commercial and industrial applications at flow rates up to 100 GPM (380 LPM).

The UV-100 System contains an array of 6 low-pressure, high output UV lamps in a 316L stainless steel reaction chamber. It is equipped with a control panel that has an integrated UV Monitor to monitor the UV light intensity in real time. The UV monitor will alarm if the UV power delivered to the water is inadequate. A powered contact on the monitor can be used to drive a solenoid-type valve to shut off the flow of water.


This system may be connected in series or in parallel for high-dose or high-volume applications, and complete systems including high-volume pre-filtration can be configured.


Features

Benefits

► 6 UV Lamp Array► Single UV Monitor► 316L Stainless Steel► Compact Footprint► Rugged Construction► NEMA Control Panel► Individual Lamp Indicators

High Volume DisinfectionLow Cost per LitreExtreme UV Dose Available for Many ApplicationsLarger Flow Rates Possible with ManifoldingMay be Configured for Redundant OperationsSystems May be Skid Mounted for Ease of Transport and InstallationExtremely Simple to Use and MaintainMade in Canada

► ► ► ► ► ► ►►

Dimensions (inches)

Dual UV-100 in Manifold

57

Flow

Rat

e (L

PM)

UV Dose in mJ/cm2

Flow

Rat

e (G

PM)

UV-100 UV Dose Response Curve



SpecificationsRated Flow: 379 litres per minute (100 GPM) 22,740 litres/hour (22.7 m3/h), 546 m3/day (6,000 gallons/hour, 144,000 gallons/day)Initial UV Dose at Rated Flow: 49 mJ/cm2 (49,000 μWsec/cm2) @ 95% UVT 37 mJ/cm2 (37,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P100/QD4E-1) 220-240 Volt AC / 50-60 Hz (Part # P100/QD4E-2)Power Consumption: 450 VA @ 120 V, 520 VA @ 230 VBallast: Electronic Ballast (6) (Part # 4-13B-PN) w/ Lamp Out Alarm (1), Power LED (6)Lamps, Wattage, Current: 6 Lamps (at 84 Watts each, 800 mA) (Part # RL-84/893T5)UV Monitor: IntegratedSize and Weight (Chamber): 46x8x10.5 inches, 90 lbs / 41 kgMax. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 2” MNPT In/OutChamber Material: 316L Stainless SteelControl Panel: NEMA IV Box, 24x20x10 inches, Non-Metallic Includes Lamp LEDs, Power Switch, UV Monitor Meter Face

2” Solenoid Valve for Fail-Safe Operation, Triggered by UV Monitor


Volt-Free Contacts on Control Panel for Remote Signaling of Operations

Integrated Surge Protector

Integrated Hour Meter

Dose Chart

FiltrationThis UV System assumes certain water quality parameters to be met for proper operation. If the source water does not meet the following criteria, pretreatment has to be considered:Turbidity (Suspended Solids): must be < 1 NTU at the time of disinfection. There must be a 5 micron or less sediment prefiltration system installed before the UV system.Total Hardness (Sum of Calcium and Magnesium): Must be < 10 gpg (grains per gallon)Iron: Must be < 0.3 ppm (parts per million)Manganese: Must be < 0.05 ppm

Pre-Filtration for this UV system is available. Please inquire.


150 GPM Rack MountedWater Purification System

Economical Chemical free UV Disinfectionat High Volume

Available with MNPT In/Out Ports or with Flanges

59


SPECIFICATIONS

WYCKOMAR SYS5100F-3 Rack MountRated Flow: 567 litres per minute (150 gpm) 34,065 litres/hour, 817,560 litres/day (9,000 gallons/hour, 216,000 gallons/ day)Initial UV Dose at Rated Flow: 47 mJ/cm2 (47,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Approx. Power Usage: 680 WMaximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 3” MNPT In/Out (Flanges Optional)Chamber Material: 316L Stainless Steel Additional Features (Optional): Sanitary Tubing and Fittings UV-Monitor, Solenoid Valve Electronic De-Scaling System Surge Protector, NEMA Control Panel

This All-in-One Water Treatment System, installed at the point of entry, is ideal for industrial and agricultural operations, such as dairy farms or bottling plants, where high flow rates are needed. Harmful microorganisms such as viruses, bacteria and proto-zoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmo-nella, Shigella, Streptococcus and many others).

Dose Chart

Various Pre-Filtration OptionsThis powerful, high volume sterilizer can be combined with different pre-filtration solutions, such as multi-cartridge filtration in stainless stell filter housings, or high-volume filtration in Polypropylene Jumbo housings.

This rack mounted system offers very efficient water treatment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.

Specifications may be subject to change

SYS5100F

60

Description

UV-5007 SystemUltra Violet Water Sterilizer

The UV-5007 System is a robust, efficient and cost-effective sterilizer designed for the disinfection of drinking and/or process water in commercial and industrial applica-tions at flow rates up to 220 GPM (833 LPM).

The UV-5007 System contains an array of 7 low-pressure, high output UV lamps in a 316L stainless steel reaction chamber. It is equipped with a control panel that has an integrated UV Monitor to monitor the UV light intensity in real time. The UV monitor will alarm if the UV power delivered to the water is inadequate. A powered contact on the monitor can be used to drive a solenoid-type valve to shut off the flow of water.


This system may be connected in series or in parallel for high-dose or high-volume applications, and complete systems including high-volume pre-filtration can be configured.


Features

Benefits

► 7 UV Lamp Array► Single UV Monitor► 316L Stainless Steel► Compact Footprint► Rugged Construction► NEMA Control Panel► Individual Lamp Indicators

High Volume Disinfection, Low Cost per LitreExtreme UV Dose Available for Many ApplicationsLarger Flow Rates Possible with ManifoldingMay be Configured for Redundant OperationsSystems May be Skid Mounted for Ease of Transport and InstallationExtremely Simple to Use and Maintain

► ►

► ► ►

►

Also availablein 90° construction

61



SpecificationsRated Flow: 833 litres per minute (220 GPM) 50,000 litres/hour (50 m3/h), 1,200 m3/day (13,200 gallons/hour, 316,800 gallons/day)Initial UV Dose at Rated Flow: 40 mJ/cm2 (40,000 μWsec/cm2) @ 95% UVT 28 mJ/cm2 (28,000 μWsec/cm2) @ 70% UVTElectrical: 110-130 Volt AC / 50-60 Hz (Part # P5007/QS4E-1) 220-240 Volt AC / 50-60 Hz (Part # P5007/QS4E-2)Power Consumption: 660 VA @ 120 V, 685 VA @ 230 VBallast: Electronic Ballast (7) (Part # 4-13B-PN) w/ Lamp Out Alarm (1), Power LED (7)Lamps, Wattage, Current: 7 (at 110 Watts each, 800 mA) (Part # RL-110/1197T5)UV Monitor: IntegratedSize and Weight (Chamber): 56x20x12.5 inches, 130 lbs / 59 kgMax. Operating Temperature: 37 °C (98.6 °F)Max. Operating Pressure: 125 psi - 8.6 bar (tested to 500 psi)Plumbing: 3” Flanges In/OutChamber Material: 316L Stainless SteelControl Panel: NEMA IV Compl., 24x20x10 inches, Non-Metallic Includes Lamp LEDs, Power Switch, UV Monitor Meter Face

3” Actuated Butterfly Valve (PVC or SS) for Fail-Safe Operation, Triggered by UV Monitor


Volt-Free Contacts on Control Panel for Remote Signaling of Operations

Integrated Surge Protector

Dose Chart

FiltrationThis UV System assumes certain water quality parameters to be met for proper operation. If the source water does not meet the following criteria, pretreatment has to be considered:Turbidity (Suspended Solids): must be < 1 NTU at the time of disinfection. There must be a 5 micron or less sediment prefiltration system installed before the UV system.Total Hardness (Sum of Calcium and Magnesium): Must be < 10 gpg (grains per gallon)Iron: Must be < 0.3 ppm (parts per million)Manganese: Must be < 0.05 ppm

Pre-Filtration for this UV system is available. Please inquire.

Part # P5007/QS4E-1/2

62

Wastewater Purification Systems Powerful UV Disinfection for Effluent Wastewater

Small Footprint – High UV Dose Equipped with Air-Drive Wiper System

Ideal for Use on Board of Ships

63

Effluent Wastewater Applications

UV Disinfection – the Chemical Free Choice

Small Footprint

The Quattra Wastewater Treatment Systems from Wyckomar are designed to provide the maximum UV disinfection based on flow rates and effluent quality. The Quattra series offers reliability and a compact footprint so these units may be used in a wide variety of applications where space is at a premium, especially on board of ships. The heart of the Quattra series of UV systems is the four lamp array of high intensity UV lamps to apply the required UV dose for significant bacterial load reduction. The Quattra UV's incorporated and adjustable integrated wiper systems help provide optimum UV penetration by maintaining a clean quartz sleeve inside the UV reactor. These systems can be installed as a single unit or as part of a modular array for higher flow rates. It is recommended that the Quattra series UV systems be installed as part of a re-circulating waste water treatment system in order to achieve the maximum bacterial load reduction possible for the specific source effluent.

Available in 2 models Typical Schematic of On-Board Sewage System

64


Fail-Safe Operation

The Quattra 50-UV System is equipped with a control panel that has an integrated UV Monitor to monitor the UV light intensity in real time. A solenoid valve can be driven by the monitor to shut off the flow of water if an inadequate UV power is detected. This industrial water purification system offers very efficient water treatment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.

The Quattra 50-UV System is a small footprint, high dose disinfection sterilizer unit for the treatment of effluent wastewater. It is equipped with a pneumatic air- drive wiper system (on-site air required) for low-maintenance operation and is very well suited for use aboard ship and in other applications where space is at a premium. The Quattra 50-UV is designed to significantly reduce bacterial load in effluent wastewater and is an integral part of a full wastewater treatment program

SPECIFICATIONS

WYCKOMAR Quattra 50-UV System

Clear Water Rated Flow: 189 litres per minute (50 GPM) 11,340 litres/hour, 272,160 litres/day (3,000 gallons/hour, 72,000 gallons/day) Initial UV Dose at Rated Flow: 40 mJ/cm2 (40,000 uwsec/cm2) @ 50% TElectrical: 110-130V / 50-60 Hz

220-240V/ 50-60 Hz Number of Lamps: 4 (at 44 Watts each) Size and Weight: 32 x 8 x 11 in., 150 lbs / 68 kg

Maximum Operating Temp: 40oC (104oF) Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi) Plumbing: 1 1/4” MNPT In/Out Chamber Material: 316L Stainless Steel Control Panel: Integrated UV-Monitor Additional Features (Optional): Solenoid Valve,

Electronic Deposit Control

Manufactured in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph Ontario Canada N1K 1A8 Phone 1-800-419-5162 Fax 519-763-6580 [email protected]

65


Fail-Safe Operation

The Quattra 90-UV System is equipped with a control panel that has an integrated UV Monitor to monitor the UV light intensity in real time. A solenoid valve can be driven by the monitor to shut off the flow of water if an inadequate UV power is detected. This industrial water purification system offers very efficient water treatment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.

The Quattra 90-UV System is a small footprint, high dose disinfection sterilizer unit for the treatment of effluent wastewater. It is equipped with a pneumatic air- drive wiper system (on-site air required) for low-maintenance operation and is very well suited for use aboard ship and in other applications where space is at a premium. The Quattra 90-UV is designed to significantly reduce bacterial load in effluent wastewater and is an integral part of a full wastewater treatment program

SPECIFICATIONS

WYCKOMAR Quattra 90-UV System

Clear Water Rated Flow: 350 litres per minute (93 GPM) 21.000 litres/hour, 504,000 litres/day (5580 gallons/hour, 133,000 gallons/day)Initial UV Dose at Rated Flow: 40 mJ/cm2 (40,000 uwsec/cm2) @ 50% TElectrical: 110-130V / 50-60 Hz

220-240V/ 50-60 Hz Number of Lamps: 4 (at 86 Watts each) Size and Weight: 50 x 8 x 11 in., 286 lbs / 130 kg

Maximum Operating Temp: 40oC (104oF) Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi) Plumbing: 1 1/2” MNPT In/Out Chamber Material: 316L Stainless Steel Control Panel: Integrated UV-Monitor Additional Features (Optional): Solenoid Valve,

Electronic Deposit Control

Manufactured in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph Ontario Canada N1K 1A8 Phone 1-800-419-5162 Fax 519-763-6580 [email protected]

66

Customized Water Puri�cation SystemsCommercial and Industrial Water Treatment Solutions

Removal / Reduction of Many Di�erent Waterborne ContaminantsUV Disinfection for a Wide Array of Applications

High Volume Treatment250 GPM / 950 LPMFiltration and UV Disinfection

Hard Water Treatment10 GPM / 38 LPMSoftening, Iron Removal and UV Disinfection

Food Processing50 GPM / 189 LPMFiltration and UV DisinfectionSanitary Design

4 GPM / 15 LPMFiltration and UV DisinfectionO� Grid

Skid Mounted Puri�cation System

Solar Powered UV System

50 GPM /189 LPMFiltration and UV Disinfection

Skid Mounted System100 GPM /390 LPMFiltration and UV Disinfection

67

Wyckomar specializes in custom made systems that will solve your water treatment needs based on your individual circumstances. We can build systems to specific flow rates, water quality specifications and/or available footprint space.

Skid mounted for easy installation and simple maintenance, your custom water treatment system is available in a variety of power configurations, with many optional features and functions.

Combining several water treatment technolo-gies in a custom solution for your special

Ultra Violet Disinfection in Customized Commercial/Industrial Water Treatment Systems

requirements is often the most effective way to deal with specific water treatment issues. Wyckomar will help you determine the best systems and sub-systems to use, we'll provide custom system drawings and we'll build your water treatment system to provide you with many years of trouble-free operation.

Our manufacturing facility at Guelph, Ontario Canada is able to build, pack, and ship your system to anywhere in the world via sea-freight and often via air-freight if required. Your custom water treatment system is built on-time and on-budget – why not contact us today with your custom water treatment specifications, and see what we can do for you?

68

50 GPM Skid MountedWater Purification System

Dual Filtration for Sediment and Taste/OdourFail-Safe Operation with UV Monitor & Solenoid Valve

69


SPECIFICATIONS

WYCKOMAR 50 GPM Skid MountRated Flow: 189 litres per minute (50 gpm) 11,340 litres/hour, 272,160 litres/day (3,000 gallons/hour, 72,000 gallons/ day)Initial UV Dose at Rated Flow: 47 mJ/cm2 (47,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Approx. Power Usage: 220 WMaximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 2” MNPT In/OutChamber Material: 316L Stainless Steel Filtration (in SS Housings): 5 Micron Sediment Filter 5 Micron Carbon Filter Additional Features (Optional): UV-Monitor, Solenoid Valve

This All-in-One Water Treatment System, installed at the point of entry, is ideal for multi-residential, commer-cial and industrial operations, such as campgrounds, large farms or bottling plants, where the drinking water is supplied by the municipality, drawn from a well or from a lake or a river. It will purify the water of most contami-nants found in groundwater, especially sediments, low to normal levels of iron and manganese and pesticides as well as taste and odour, including sulphur smell. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

Dose Chart

Fail-Safe Operation with UV-MonitorThe monitor is a safety device that monitors the UV systems’ effective-ness in real time and displays the UV intensity on the meter face. The monitor will sound an alarm and trigger a solenoid volume to shut off the water flow in case the UV lamp burns out or the dose is inadequate for proper disinfection.

This skid mounted system offers very efficient water treatment at a low cost per unit volume. The system is designed for ease of installation and is fully tested prior to shipment.


UV-5000

70

Skid Mounted Water Treatment Systemfor General Applications - 50 GPM

Multiple Levels of Filtration IncludingSediment / Taste & Odour / VOC’s

UV Disinfection and Fail-Safe Operation with Solenoid Valveand Built In Alarm System.

Electronic De-Scaling System OptionalSimple to Install and Operate Anywhere

71


SPECIFICATIONS

WYCKOMAR 50 GPM Skid Mount IIRated Flow: 189 litres per minute (50 gpm) 11,340 litres/hour, 272,160 litres/day (3,000 gallons/hour, 72,000 gallons/ day)Initial UV Dose at Rated Flow: 47 mJ/cm2 (47,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Approx. Power Usage: 220 WMaximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 2” MNPT In/OutChamber Material: 316L Stainless Steel Filtration (in SS Housings): 5 Micron and 1 Micron Sediment Filter 5 Micron Carbon Filter Additional Features (Optional): UV-Monitor, Solenoid Valve Electronic De-Scaling System

This All-in-One Water Treatment System, installed at the point of entry, is ideal for multi-residential, commercial and industrial applications, such as campgrounds, large farms or bottling plants, where the drinking water is supplied by the municipality, drawn from a well or from a lake or a river. It will purify the water of most contami-nants found in water, especially sediments, low to normal levels of iron and manganese and pesticides as well as taste and odour, including sulphur smell. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

Dose Chart

Fail-Safe Operation with UV-MonitorThe monitor is a safety device that monitors the UV systems’ effective-ness in real time and displays the UV intensity on the meter face. The monitor will sound an alarm and trigger a solenoid volume to shut off the water flow in case the UV lamp burns out or the dose is inadequate for proper disinfection.



UV-5000

72


Sediment Filtration and UV Disinfection for RecirculationOnboard Pump, Sanitary Fittings

Optional withDual Pre-Filtrattion

73


SPECIFICATIONS

WYCKOMAR SKD5000-JCHX1 Skid MountRated Flow: 189 litres per minute (50 gpm) 11,340 litres/hour, 272,160 litres/day (3,000 gallons/hour, 72,000 gallons/ day)Initial UV Dose at Rated Flow: 47 mJ/cm2 (47,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Approx. Power Usage: 220 WMaximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 1.5” Sanitary Clamps In/OutChamber Material: 316L Stainless Steel Filtration: 5 Micron Sediment Filter in SS Housing Post Filter in BigBlue HousingPump: Stainless Steel OnboardAdditional Features (Optional): UV-Monitor, Solenoid Valve

This All-in-One Water Treatment System is designed for the food industry for the purification of holding tank contens in a recirculation loop or similar applications. It filters the water with a sediment filter down to 5 microns. Harmful microorganisms such as viruses, bacteria and proto-zoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmo-nella, Shigella, Streptococcus and many others). The system features sanitary tubing and fittings for maximum cleanability.

Dose Chart

Fail-Safe Operation with UV-MonitorThe (optional) monitor is a safety device that monitors the UV systems’ effectiveness in real time and displays the UV intensity on the meter face. The monitor will sound an alarm and trigger a solenoid volume to shut off the water flow in case the UV lamp burns out or the dose is inadequate for proper disinfection.



UV-5000

74


Manual Valves and Dual Filtration ConfigurationFail-Safe Operation with UV Monitor and Solenoid Valve

75


SPECIFICATIONS

WYCKOMAR 100 GPM Skid MountRated Flow: 378 litres per minute (100 gpm) 22,680 litres/hour, 544,320 litres/day (6,000 gallons/hour, 144,000 gallons/ day)Initial UV Dose at Rated Flow: 47 mJ/cm2 (47,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Approx. Power Usage: 460 WMaximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 2” MNPT In/OutChamber Material: 316L Stainless Steel Filtration (in SS Housings): 5 Micron Sediment Filter 5 Micron Carbon Filter Additional Features (Optional): UV-Monitor, Solenoid Valve, Electronic De-Scaling System

This All-in-One Water Treatment System, installed at the point of entry, is ideal for commercial and industrial operations where the drinking water is supplied by a well or drawn from surface water. The system consists of 2 UV units in manifold, for a high flow rate. It will purify the water of most contaminants found in groundwater and surface water, especially sediments, low to normal levels of iron and manganese and pesticides as well as taste and odour, including sulphur smell. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others).

Dose Chart

Fail-Safe Operation with UV-MonitorThe monitor is a safety device that monitors the UV systems’ effective-ness in real time and displays the UV intensity on the meter face. The monitor will sound an alarm and trigger a solenoid volume to shut off the water flow in case the UV lamp burns out or the dose is inadequate for proper disinfection. Additionally, it features manual shut off valves.



76

High Volume Water Treatment SystemMultiple Levels of Sediment Filtration to 1 Micron

UV DisinfectionEasy Change Filter Cartridges

Compact Foot Print - Various Flow Rates Available

77


SPECIFICATIONS

WYCKOMAR High Volume Skid MountRated Flow: 946 litres per minute (250 gpm) 56,7600 litres/hour, 1.36 mio litres/day (15,000 gallons/hour, 360,000 gallons/ day)Initial UV Dose at Rated Flow: 35 mJ/cm2 (35,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Approx. Power Usage: 800 WMaximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 3” Flange In/OutChamber Material: 316L Stainless Steel Filtration (in SS Housings): 20 and 1 Micron Sediment Filter Custom Filter Configurations Available Additional Features (Optional): UV-Monitor, Solenoid Valve Electronic De-Scaling System

This All-in-One Water Treatment System, installed at the point of entry, is ideal for commercial and industrial operations where a high volume output is required, e.g. for process water disinfection. The system is based on the UV-5007 steril-izer and offers multiple levels of sediment filtration down to 1 micron, using high-volume, non-metallic filter housings that make the change of cartridges very easy. Harmful microor-ganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others). The design of the system allows mani-folding of multiple units and individual filter configurations for many different application up to flow rates requirements of 1000 GPM (3,800 LPM)

Dose Chart

Fail-Safe Operation with UV-MonitorThe (optional) monitor is a safety device that monitors the UV systems’ effectiveness in real time and displays the UV intensity on the meter face. The monitor will sound an alarm and trigger a solenoid volume to shut off the water flow in case the UV lamp burns out or the dose is inadequate for proper disinfection.



UV-5007

78

Transportable 250 GPM (~1000 LPM)Water Treatment SystemMultiple Filtration Levels to 1 Micron

UV DisinfectionChlorine Residual for Downstream Protection

Turbidity - ORP - Real-Time UV Monitoring Built InPressure Gauges - Test Ports - Alarm functions Built In

79


SPECIFICATIONS

WYCKOMAR 250 GPM Skid MountRated Flow: 946 litres per minute (250 gpm) 56,7600 litres/hour, 1.36 mio litres/day (15,000 gallons/hour, 360,000 gallons/ day)Initial UV Dose at Rated Flow: 35 mJ/cm2 (35,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Approx. Power Usage: 700 WMaximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 3” Flange In/OutChamber Material: 316L Stainless Steel Filtration (in SS Housings): 50, 20 and 1A Micron Sediment Filter Custom Filter Configurations Available Additional Features (Optional): Real Time Monitoring of UV, TDS, ORP Pressure gauges, Test Ports, Solenoid Valve

This All-in-One Water Treatment System, installed at the point of entry, is ideal for commercial and industrial operations where a high volume output is required, e.g. for process water disinfection. The system offers multiple levels of sediment and carbon filtration down to 1 micron, using high-volume, stainless steel filter housings and is ideal for the treatment of ground or surface water. It will purify the source water of most harmful microor-ganisms such as viruses, bacteria and protozoa with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legion-ella, Salmonella, Shigella, Streptococcus and many others). The water is enriched with chlorine on its last stage for down-stream protection.This skid mounted system offers very efficient water treatment at a low cost per unit volume. The system is designed for transportation and installation and is fully tested prior to shipment.

Dose Chart

Fail-Safe Operation with UV-MonitorThe monitor is a safety device that monitors the UV systems’ effective-ness in real time and displays the UV intensity on the meter face. Turbidity and ORP levels may also be monitored based on configura-tion chosen. The monitor will sound an alarm and trigger a solenoid shut-off valve in case the UV lamp burns out or the dose is inadequate for proper disinfection. Presure gauges on the filter housings ensure easy monitoring of the filter status.


UV-5007

80

Cabinet MountedWater Treatment System

Ozone - Backwashable Filtration - UV DisinfectionFinal Polish Filtration to Sub-Micron Level

Various Configurations and Flow Rates Available

81


SPECIFICATIONS

WYCKOMAR Cabinet Mount Water TreatmentCombines Iron Removal with UV Disinfection and Multi-Level Filtration in a Secure Cabinet

Rated Flow: 38 litres per minute (10 gpm) 2,280 litres/hour, 54,720 litres/day (600 gallons/hour, 14,400 gallons/ day)Initial UV Dose at Rated Flow: 55 mJ/cm2 (55,000 μwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz 220-240V/ 50-60 Hz Maximum Operating Temp: 37 oC (98.6 oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 1” MNPT In/OutChamber Material: 304L Stainless Steel (316L available)Filtration: Backwashable Carbon Filter (2 cf of media) Ozone: Air Dryer, Ozone Generator, Contact Tank, Venturi InjectorPolish Filtration: 20 and 5 Micron Sediment, 10 M CarbonOptional: On Board Pump

This portable All-in-One Water treatment System, installed at the point of entry, is designed for the treatment of well water to a potable purity level. It combines ozone injection technology with efficient high-volume carbon filtration, optimized especially for the removal of higher than normal levels of iron and manganese. It is ideal for com-mercial, industrial and outdoor applications. The integrated UV-1500 sterilizer kill pathogens (harmful microorganisms such as viruses, bacteria and protozoa) with a power-ful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptospo-ridium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many othersThe system includes manual shutoff valves and an optional glycol flushing tank for trouble-free stand-by mode under freezing outdoor conditions).

Dose Chart

Water Treatment in Secure CabinetThis cabinet mounted system offers very efficient water treatment. It can easily be upgraed for higher flow rates. The lockable cabinet safeguards the equipment against tampering and manipulation, for peace of mind when used in critical environments.

The system is fully tested prior to shipment.


UV-1500

82

Skid Mounted Hard Water Treatment SystemWater Softening – Iron Removal – UV Disinfection

Simple To Install and Operate Anywhere – Custom Systems AvailableVarious Flow Rates Available

83

SPECIFICATIONS

WYCKOMAR Hard Water Treatment SystemSoftening – Iron Removal – UV-Disinfection

Rated Flow: 38 litres per minute (10 GPM)22800 litres/hour, 54,720 litres/day(600 gallons/hour, 14,400 g/ day)

Initial UV Dose at Rated Flow: 63mJ/cm2 (63,000 uwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz

220-240V/ 50-60 Hz Maximum Operating Temp: 37oC (98.6oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 1” MNPT In/OutChamber Material: 304L Stainless Steel (316L available)Filtration: Backwashable Birm Filter (2 c/f of media)

Includes Air Injection, Off Gas ValveWater Softener: 70,000 GrainPolish Filtration: 5 Micron Sediment

This portable All-in-One Water Treatment System, installed at the point of entry, is designed for the treatment of well water to a high purity level. It is ideal for commercial and industrial applications in hard water regions. The system combines high volume air birm filtration and water softening for removal of high iron and manganese levels. The integrated UV-1200 sterilizer kills pathogens (harmful microorganisms such as viruses, bacteria and protozoa) with a powerful UV disinfection dose at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmonella, Shigella, Streptococcus and many others). The system includes manual shut-off valves.

Dose Chart

Treat Multiple Water Quality Issues With One SystemThe system as pictured is designed for a flow rate of 12 GPM, but can easily be upgraded for higher flow requirements.


Manufactured in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph Ontario Canada N1K 1A8Phone 1-800-419-5162 Fax 519-763-6580 [email protected]


84

Water Purification Systems For Use In Hazardous Areas And Extreme Environments

Class I Division II CertifiedHeat Tracing Available For Use In Sub-Zero EnvironmentsMultiple Filtration Levels to 1 Micron Plus UV DisinfectionVarious Flow Rates Available – Custom Systems Available

85

SPECIFICATIONS

WYCKOMAR 60 GPM Class I Division II for use in Hazardous Areas - Skid Mount

Rated Flow: 226 litres per minute (60 GPM)13560 litres/hour, 325440 litres/day(3600 gallons/hour, 86400 gallons/ day)

Initial UV Dose at Rated Flow: 36 mJ/cm2 (36,000 uwsec/cm2) @ 95% TElectrical: 100-130V / 50-60 Hz / 192 VA

220-240V/ 50-60 Hz / 154 VAMaximum Operating Temp: 37oC (98.6oF)Maximum Operating Pressure: 125 psi – 8.6 bar (tested to 500 psi)Plumbing: 3” Flange In/OutChamber Material: 304L Stainless Steel (316L available)Filtration (in SS Housings): Sediment 50, 20 and 1 Micron Absolute

Carbon Block 5 MicronAdditional Features: CIDII Rated Enclosure

This All-in-One Water Treatment System, installed at the point of entry, is ideal for heavy-duty industrial applications in extreme environments. The enclosure is Class I Division II Certified explosion-proof. The system will purify the source water (drawn from a well or a lake) of most contaminants such as sediments, heavy metals and pesticides with filtration in 3 stages down to 1 micron. Carbon filtration reduces taste and odor, including sulphur smell. Harmful microorganisms such as viruses, bacteria and protozoa are killed with a powerful UV disinfection dose that will inactivate the pathogens at a kill rate of >99.9% (Giardia, E.coli, Cryptosporidium, Vibrio cholera, Legionella, Salmo-nella, Shigella, Streptococcus and many others).

Dose Chart

Hazardous Areas Are No ProblemThis Skid Mounted system offers very efficient water treatment for use in extreme environments at a low cost per unit volume. The system is designed for ease of installation and is fully tested and certified prior to shipment.

Manufactured in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph Ontario Canada N1K 1A8Phone 1-800-419-5162 Fax 519-763-6580 [email protected]


86

Solar PoweredUV Drinking Water Purification System

Off-Grid Water Treatment for Use Anywhere, Mounted on CartPump, Dual Filter Set, UV Disinfection

12 Volt Power Pack, 80 Watts Solar Panel

87

Description

Features

Benefits100% Pollution FreeEasy Transportation and SetupMinimal Maintenance RequiredSafe and Good Tasting Drinking Water, AnywhereLow Operating Cost

► ► ►►►

SYS250-SPQD4EWater Treatment System

The Solar Powered UV-250 System combines high quality pre-filtration with our proven ultraviolet purification technology to produce a complete water quality system for use in “off-grid” applications, where no power outlet is available. It is designed to treat water from drilled or dug wells, ponds, and lakes, streams, or collected rainwater. The filter system comprises a sediment filter that removes particulate matter such as silt, dirt, rust and other suspended solids down to 5 microns, and a carbon block filter that removes/reduces dissolved solids such as minerals, pollutants and VOC’s and also neutralizes taste and odours that may be present in the source water. The filter set can easily be customized for the removal of other contaminants.The integrated UV-250 ultraviolet sterilizer kills pathogens (harmful microorganisms such as viruses, bacteria, fungi and proto-zoa) with a powerful UV disinfection dose at a kill rate of >: 99.9% (Giardia, E. coli, Cryptosporidium parvum, M. tuberculosis, Vibrio cholerae, Hepatitis virus, Legionella, Pseudomonas, Paramecium, Salmonella, Shigella, Polio virus, Streptococcus and many others).This portable water filtration system collects sunlight to charge the on-boardf battery pack. It then uses the generated power to pump and process local source water to produce high-quality and safe drinking water for human consumption. It requires no gasoline or other fuels, and is ideal for areas with little or no power sources and poor water quality, especially in remote areas or disaster zones.

► Chemical-Free Water Treatment► Robust Construction, Pre-Assembled ► Sturdy, Maintenance-Free 80 w Solar Module, Expandable to 240 w Array► Deep Cycle, 105 amp-hour Sealed Battery ► Charge Controller with LCD Display► Can be Configured for Less Common Pathogens and Contaminants

Similar to image.

The system is designed for remote

areas and ships complete with all

necessary compo-nents and installation

hardware.

88



SpecificationsRated Flow: Up to 12 litres per minute (3 GPM) Daily water production depending on number of panels, hours of sunshine and location latitude (typically 1-3 h runtime per day, 180-360 GPD / 700 - 1400 Lpd)Initial UV Dose at Rated Flow: 46 mJ/cm2 (46,000 μsec/cm2) @ 95% UVT 32 mJ/cm2 (32,000 μsec/cm2) @ 70% UVTElectrical: 12 VDC Sealed “Non-Spillable” Battery Power Pack 80 W Solar Panel 17 V, 4.7 A Pump 12 V, 3 chamber diaphragm, up to 9 ft priming Power Consumption: 5.7 VA @12 VDCBallast: Electronic Ballast (Part # 4-BL28W-12V) w/ Lamp Out Alarm, Power LED Replacement Lamp: Low-Pressure UV Lamp, Part # RL-23/436T5Filtration: 10” SlimLine (L 9-7/8“, OD 2-1/2”), w/ Pressure ReliefStage 1, Sediment Filter: Melt-Blown Polypropylene (“Spun Poly”), 5 MicronStage 2, Carbon Filter: Coconut Shell Carbon (“Extruded Carbon Block”) Max. Operating Temperature: 40 °C (98.6 °F)Plumbing: Standard Garden Hose ConnectionsShipping Size and Weight: 1 skid 54 x 49 x 23, 280 lbs

Expandable Array up to 3 Solar Panels

Choice of Inverters Available (for 110V 60 Hz or 230V 50 Hz)

Additional Filtration Stages for Less Common Contaminants

Flow Meter for Display of Overall Production, Pressure Gauges, Hour Meter for Lamp Runtime Display

Water Treatment Box

Solar Panel Sample Run TimesPerformance of this system varies greatly depending on the number of solar panels in the array (up to 3 can be installed) and the location of operation. Daily average sunlight hours, depending on the season, in combination with the distance to the equator, have significant influence on the overall production time. For example, in Manila, Phillippines, the average peak sunshine hours in July are approx. 4.3 per day, this will provide 1.4 h of runtime with one panel, 2.9 h with 2 and 4.3 h with 3 panels, for a production of 1000 litres per day with 1 panel, 2100 litres with 2 panels and 3100 litres with 3 panels. In April, the average peak shunshine hours are approx. 8.6 hours, so the daily runtime would be 2.9 h with 1 panel (2100 litres production per day), 5.8 hours with 2 panels (4200 litres per day) and 8.7 h with 3 panels (6300 litres per day).

Part # SYS250-SPQD4E

The filter cartridges in this system have a great surface area for long life and reduced filtration costs. The pump is self-priming and can lift up to 9 ft. Tubing forinlet is supplied and comeswith a strainer.

89

Reverse Osmosis SystemsResidential and Commercial Applications

Models with and without Booster PumpComplete Systems for Residential and Commercial

Sea Water Desalination Systems

Whole House RO250-1200 GPDPoint-of-Entry

Sea Water RO250-1200 GPDUse onboard ships

Residential RO with UV50 GPDPoint-of-Use

91

Description

Specifications Installation Diagram

5 Stage ROResidential Drinking Water System

This residential Reverse Osmosis System is installed at the point of use (e.g. under the sink) and produces up to 50 gallons of purified water per day. It removes substantial amounts of most inorganic chemicals (such as salts, minerals, metals) and most (but not all) organic chemicals. The high quality membrane rejects successfully salts, sugars, proteins, particles, dyes, heavy metals, chlo-rine and related by-products as well as other contaminants that have a molecular weight greater than 150-250 daltons. Dissolved ions that carry a charge, such as salts, are more likely to be rejected than uncharged ions, such as organics.

The system comes with 3 levels of pre-filtration, a 50 GPD Filmtec membrane, a post-carbon filter and a metal holding tank. Mounting hardware, a long reach faucet and saddle valves for easy installation are supplied with the system.

Optional stages are also available, such as UV-Disinfection, calcite filter for re-mineralization, or electronic de-scaling.

Features► Metal Storage Tank ► Filmtec RO Membrane► Long Reach Chrome Faucet► Quick Connect Fittings► Made In USA

Capacity 50 GPD, Tank Capacity 4 gal.Recovery 20-25%, Rejections 90% minFiltration:- 5 M Sediment (Part # 14-WFS10-5SP)- GAC Carbon (Part # 14-WFC10-GAC)- Carbon Block (Part # 14-WFC10-5CB)- Post Carbon (Part # 14-WROPC-GAC-1)Membrane Filmtec (Part # 14-WROM-50GP)

Source Water Requirements:Hardness < 1 gpgFree chlorine 0 ppmTDS < 1,000 ppmpH 3 - 11Iron < 0.01 ppmManganese < 0.05 ppmTurbidity < 1 NTUTemperature 4 °C (40 °F) - 27 °C (80 °F)Pressure 40 - 100 psi (2.8 - 5.6 bar)

Wyckomar Inc. 111 Malcolm Road Guelph, Ontario, Canada N1K 1A8 Ph: 1-800-419-5162 or 519-822-1886 Fx: 519-763-6580 email: [email protected] www.wyckomaruv.com

93

Description

SpecificationsInstallation Diagram

6 Stage ROResidential Drinking Water System

This residential Reverse Osmosis System is installed at the point of use (e.g. under the sink) and produces up to 50 gallons of purified water per day. It removes substantial ampounts of most inorganic chemicals (such as salts, minerals, metals) and most (but not all) organic chemicals. The high quality membrane rejects successfully salts, sugars, proteins, particles, dyes, heavy metals, chlorine and related by-products as well as other contaminants that have a molecular weight greater than 150-250 daltons. Dissolved ions that carry a charge, such as salts, are more likely to be rejected than uncharged ions, such as organics.

Bacteria and viruses and other microorganisms are killed by a powerful UV disinfection that will inactivate the pathogens at 99.99% inactivation rate.

The system comes with 3 levels of pre-filtration, a 50 GPD Filmtec membrane, a post-carbon filter and a metal holding tank. Mounting hardware, a long reach faucet and saddle valves for easy installation are supplied with the system.

Features► Metal Storage Tank ► Filmtec RO Membrane► Long Reach Chrome Faucet► Quick Connect Fittings► Powerful UV Disinfection

Capacity 50 GPD, Tank Capacity 4 gal.Recovery 20-25%, Rejections 90% minFiltration:- 5 M Sediment (Part # 14-WFS10-5SP)- GAC Carbon (Part # 14-WFC10-GAC)- Carbon Block (Part # 14-WFC10-5CB)- Post Carbon (Part # 14-WROPC-GAC-1)Membrane Filmtec (Part # 14-WROM-50GPD)Electrical: 130 V 60 HzUV Chamber 304 Stainless Steel

Source Water Requirements:Hardness < 1 gpgFree chlorine 0 ppmTDS < 1,000 ppmpH 3 - 11Iron < 0.01 ppmManganese < 0.05 ppmTurbidity < 1 NTUTemperature 4 °C (40 °F) - 27 °C (80 °F)Pressure 40 - 100 psi (2.8 - 5.6 bar)

Wyckomar Inc. 111 Malcolm Road Guelph, Ontario, Canada N1K 1A8 Ph: 1-800-419-5162 or 519-822-1886 Fx: 519-763-6580 email: [email protected] www.wyckomaruv.com

94

Description

Sea Water ROOn-Board Desalination Systems

Sea Water Reverse Osmosis Systems are designed to produce potable permeate water from sea water with up to 35,000 ppm TDS content. Designed for use on recreational yachts and light commercial vessels of all types, these systems will provide a daily production of 190 - 580 GPD (30 litres/hour - 300 litres/hour). They have a very small foot-print and silent operation which means these units can be installed in almost any area. The systems can be fully automated with the addition of select optional equipment.

Systems include select pre-filtration and optional UV disinfection to provide the highest quality drinking water possible. All systems come with high rejection rate RO membranes and feature high/low pressure gauges and safety devices. Additional optional features are available, such as automatic flushing, extended pre-filtration or remote control.

3 Models for reacreational and commercial uses are available in various voltage configu-rations and flow rates.

These desalination systems may be easily incorporated into a full on board drinking water system including pumps and pressure systems.

Model Eco

Features► Compact Design► High Pressure Feed + CAT Pump► Automatic Operation, Simple and Silent ► Salinometer, Auto Waste Valve► Very Low Power Consumption

Options► Auto Flushing► Remote Control► UV Disinfection► Wide Range of Other Options

Model X

Model Y

30-90 l/h12 or 24 V DC115 or 230 V single ph.

60-300 l/h115 or 230 V single ph.220 or 400 V three ph.

30-90 l/h12 or 24 V DC

All dimensions in inches

95

Distributed by Wyckomar Inc. 111 Malcolm Road, Guelph, Ontario Canada N1K 1A8Phone ++1-519-822-1886 Fax ++1-519-763-6580 [email protected] www.wyckomaruv.com

Specifications Sea Water RO SystemsPart

#

Eco30

Eco60

Eco90

Prod.*

(GPD)

190

380

570

Prod.*

(Litres/Hr)

30

60

90

Voltage

12 V24 V

12 V24 V

12 V24 V

12 A6 A

25 A12.5 A

24 A17 A

SizeL x W x H

(cm)

67x38x20

67x38x20

67x50x20

Weight

(kg)

4848

5656

6868

Part#

Y-60

Y-120

Y-180

Y-240

Y-300

Prod.*

(GPD)

380

760

1140

1520

1900

Prod.*

(Litres/Hr)

60

120

180

240

300

Voltage

s=single ph.t=three ph.

115 Vs

230 Vs

220 Vt

400 Vt

115 Vs

230 Vs

220 Vt

400 Vt

115 Vs

230 Vs

220 Vt

400 Vt

115 Vs

230 Vs

220 Vt

400 Vt

115 Vs

230 Vs

220 Vt

400 Vt

1.5 kW

1.5 kW

2 kW

2 kW

3 kW

SizeL x W x H

(cm)

117x45x37

117x45x37

117x45x41

117x50x41

117x50x46

Weight

(kg)

61

69

67

85

95

Part#

X-30

X-50

X-60

X-90

Prod.*

(GPD)

190

320

380

570

Prod.*

(Litres/Hr)

30

50

60

90

Voltage

12 V24 V115 V230 v

12 V

24 V115 V230 V

115 V230 V

31 A25 A1 Kw1 Kw

31 A

25 A1 kW1 kW

1 kW1 kW

SizeL x W x H

(cm)

69x33x30

69x33x30

69x33x30

69x33x30

Weight

(kg)

34363838

40

424444

5050

Mod

el E

coM

odel

XM

odel

Y

Design AssumptionsFeed Water of <35,000 mg/l TDSSDI < 3Turbidity < 1 NTU for UV Disin-fection

Standard FeaturesHigh Rejection Rate Sea Water RO membranes5 Micron Sediment Pre FilterHigh and Low Pressure Gauges and Safety DevicesStainless Steel Frame

Optional FeaturesAutomatic FlushingAdvanced PLC Control for Remote Signaling and ControlPermeate and Concentrate Flow-metersSeparation KitMaintenance KitAdditional Sand Filter

Additional Considerations

Holding TankPressure System

* Rated performance +/- 10% using standard seawater, with 35 g/l salinity, at 25 ° C

PowerConsumption

PowerConsumption

PowerConsumption

E. & O. E.

96

Electronic Ballasts and MonitorsPower Supplies for Germicidal UV Lamps

Real-Time Monitoring of UV Light IntensityOptional Outputs - Wet + Dry Contacts, 0-1 Volt, 4-20 mA

BE-425W-U BE-800WL-1 BE-800WL30-2

UV/MS-1 V3

UV/MS-1 V3 w/ 4-20 mA Output

Hour Meter

97


SPECIFICATIONS

Wyckomar Electronic Ballasts


Part #

BE-425W-U

BE-425R-U

BE-800WL-1BE-800WL-1BE-800WL30-1BE-800WL-1

BE-800WL-2BE-800WL-2BE-800WL30-2BE-800WL-2

BE-1-12V

BL-28W-12V

Lamp Type

RL-12/254T5

RL-23/436T5

RL-40/867T5

RL-12/254T5

RL-23/436T5

RL-40/867T5

RL-44/436T5RL-84/893T5RL-100/1197T6RL-110/1197T5

RL-44/436T5RL-84/893T5RL-100/1197T6RL-110/1197T5

RL-12/254T5

RL-23/436T5

PowerConsumption

18 VA @ 110V 23 VA @ 230V 29 VA @ 110V 35 VA @ 230V 53 VA @ 110V 66 VA @ 230V

16 VA @ 110V 20 VA @ 230V 27 VA @ 110V 31 VA @ 230V 48 VA @ 110V 59 VA @ 230V

57 VA @ 110V 70 VA @ 110V 85 VA @ 110V102 VA @ 110V

72 VA @ 230V 84 VA @ 230V 89 VA @ 230V107 VA @ 230V

22 VA @ 12V

24 VA @ 12V

InputVoltage

110-240VAC50/60

Hz

110-240VAC50/60

Hz

110-130 VAC50/60

Hz

210-240VAC50/60

Hz

12 V DC

12 V DC

425-

500mA

425-

500mA

800 mA

800 mA

425 mA

425 mA

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Yes

No

Yes

Opt.

Opt.

Opt.

Opt.

No

No

Opt.

Opt.

Opt.

Opt.

No

No

Timer

Opt.HourMeterResettable




No

No

Lam

pCu

rren

t

Sole

noid

Out

put

Volt-

Free

Cont

acts

Pow

er L

ED

Lam

p O

utAl

arm

Wyckomar UV Monitoring System

Part #

UV/MS-1 V3

UV/MS-2 V3

InputVoltage

110 VAC50/60 Hz

or230VAC50/60 Hz

DisplayType/

DisplayValue

Analog0-100%

Opt.w/

breakout

box

UV/MS/WDE

Opt.

Nouse

thermo-

sensitive

purge valve

YesN/O

switch

w/ jumper

to N/C

Power

2.6 VA

2.4 VA

LowUV-

DoseAlarm

Yes

Setat70%

System

all systems(optional forUV-1, UV-250)

Dry

Cont

acts

Wet

Cont

acts

Trip

Poi

nt

Ove

rtem

pRe

lay

4-20

mA

Out

put

0-1

Volt

Out

put

Opt.Part #

UV/MS-1

V3-4-20mA

98

UV Replacement Lamps and Quartz SleevesMedium Pressure UV Germicidal UV BulbsGE214 Fused Quartz Sleeves and Domes

99

Manufactured for Wyckomar Inc. 111 Malcolm Road, Guelph, Ontario Canada N1K 1A8Phone ++1-519-822-1886 Fax ++1-519-763-6580 [email protected] www.wyckomaruv.com

SPECIFICATIONSWyckomar UV Replacement Lamps (T5 Only)


Part #

RL-12/254T5

RL-23/436T5

RL-40/867T5

RL-44/436T5

RL-84/893T5

RL-100/1197T6

RL-110/1197T5

Length mm

254

436

867

436

893

1197

1197

Length inch

10.0

17.1

34.1

17.1

35.1

47.1

47.1

PowerConsumption

18 VA @ 110V 23 VA @ 230V 29 VA @ 110V 35 VA @ 230V 53 VA @ 110V 66 VA @ 230V 57 VA @ 110V 72 VA @ 230V 70 VA @ 110V 84 VA @ 230V 85 VA @ 110V 89 VA @ 230V102 VA @ 110V107 VA @ 230V

425 mA

425 mA

425 mA

800 mA

800 mA

800 mA

800 mA

38

66

115.9

131.2

176.6

3.5

7

14

27.9

36.9

30

69

144.6

264

315.4

Rated Life (Hrs)

9000

9000

9000

9000

9000

9000

9000

UVC

Wat

tsat

254

nm

UVC

per c

m2

at 1

M

Curr

ent

Volts

@ 6

0Hz

Type Fused GlassColor ClearThermal Expansion 10-7cm/cm/°C 5.5Thermal Conductivity W/m °C 1.4Specific Heat J/kg °C 670Softening Point °C 1683Strain Point °C 1120Density kg/m3 2.2Refraction Index 1.4585

Quartz Sleeves / Domes

Other types of UV lamps not listed here are available upon request:

T5 Lamp and Sleeve CombinedRL-4/178CELL Mini-ZapRL-7/254T5CELL UV-4

T8 Lamp (2pin Double-Ended)RL-250T8 RL-700T8 RL-1200/T8 RL-15/20/50T8

T12 Lamp (2pin Double-Ended)RL-30/60T12

100

Residential/Commercial Filtration SystemsHigh Quality Plastic Filter Housings in Heavy Duty Construction

FDA Grade Polypropylene, Pressure Rated to 125 psiTemperature Rated to 52° C, NSF 42 Certified

Filter Cartridges for Sediment, Iron, H2S, Chlorine, Pesticides, Taste, Odour and Colourisation Reduction

Low Pressure Drop, Increased Surface Area

Filter Cartridges10, 20, 30 inch

SlimLineBigBlue

Filter Housings10, 20, 30 inch SlimLineBigBlue

101

SPECIFICATIONS - Filter Housings

SPECIFICATIONS - Filter Cartridges

Wyckomar offers a full line of filter cartridges for residential and light commercial applications. These media reduce sediments as

well as taste, odour and colourisation from the treated water.

Plastic Filter Housings Material Bowl and Cap: PolypropyleneMaterial O-Ring: EPDMMax. Operating Temp: 52o C (125o F)Min. Operating Temp: 4.4o C (40o F)Max. Operating Pressure: 125 psi – 8.6 bar Threads available: ¾”, 1”, 1 ½”Pressure Relief Button: YesDistributed

Distributed in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph Ontario Canada N1K 1A8Phone 1-800-419-5162 Fax 519-763-6580 [email protected]


Extruded Carbon Block Media: Coconut shell Max. Operating Temp: 52o C (125o F)Min. Operating Temp: 10o C (50o F)Max. Operating Pressure: 125 psi

Granular Activated Carbon (GAC)Media: Coconut shell activatedMax. Operating Temp: 40o C (100o F)Min. Operating Temp: 4o C (38o F)Max. Operating Pressure: 125 psi

Pleated Carbon NCP SeriesMedia: Impregnated PolyesterMax. Operating Temp: 65o C (150o F)Min. Operating Temp: 4.4o C (40o F)Max. Operating Pressure: 40 PSID

Pleated Sediment Media: Polypropylene/PolyesterMax. Operating Temp: 60o C (140o F)Min. Operating Temp: 4.4o C (40o F)Max. Operating Pressure: 40 PSID

Poly Spun Sediment Media: Polypropylene (melt blown)Max. Operating Temp: 60o C (140o F)Min. Operating Temp: 4.4o C (40o F)Max. Operating Pressure: 40 PSID

Top-of-the-line filter cartridges for chlorine, taste, odour and sediment reduction. Long life, low pressure drop. 10 micron nominal rating.NSF Standard 42 certified.Available Sizes: 10”, 20”, 30”, 40”

Low cost filter cartridges for taste and odour reduction. Containing activated carbon resin. For various flow rates.

Available Sizes: 10”, 20”

This combination of a pleated polyester media and carbon filtration produces an outstanding filter cartridge with extended service life. 10 micron nominal rating. Available Sizes: 10”, 20”

Increased surface area due to pleated design, for longer life, less pressure drop and higher flow rates. Cartridges are washable and reusable. 0.5, 1, 5, 20 and 50 micron nominal ratingAvailable Sizes: 10”, 20”, 30”, 40”

Low cost, high dirt holding capacity.This is the standard sediment filter for removal of dirt, rust and other sediments from city water.NSF standard 42 certified.Available Sizes: 10”, 20”, 30”, 40”

These heavy-duty housings are made entirely of the highest quality FDA grade NSF listed polypropylene. The buttress thread design provides superior sealing and great security. Thick side walls with heavy-duty ribs provide extra strength.Available in SlimLine and BigBlue, in sizes of 10” and 20”. NSF Standard 42 certified.

103

PRESSURE DROP CHARTS - Filter Cartridges 10” and 20”

Distributed in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph Ontario Canada N1K 1A8 Phone 1-800-419-5162 Fax 519-763-6580 [email protected]


CARBON BLOCK

PLEATED CARBON

SEDIMENT PLEATED SlimLine

SEDIMENT PLEATED BigBlue

SEDIMENT POLY SPUN

104

Wyckomar Inc111 Malcolm Road

Guelph, Ontario N1K 1A8 Canada+1-519-822-1886

[email protected]

A self cleaning sediment filter (spin-down sepa-rator) at 15, 30, 60 or 104 micron will help significantly reduce the number of sediment filter cartridges used to filter surface-water sources.

This unit is installed in front of the existing filtra-tion, adding a stage for the removal of larger particulate matter that would otherwise quickly clog up the cartridge filter. It has a manual flush which is used to purge built-up sediments in the bottom of the filter. No cartridges are needed, the mesh screen can be exchanged, if need be, with an inexpensive replacement.

This type of filter will especially be appreciated by those who are using a large number of sedi-ment filter cartridges to clean up their drinking water (typically when the feed water comes from a lake or other surface-water source).

The self cleaning sediment filter is available in 3/4”, 1“, 1-1/2” or 2” in/out for flow rates up to 50 GPM. Unit and screen are made from PVC. The screens are cleanable and reusable..

This unit is an ideal companion to a cottage sized UV disinfection system to provide clean and sterilized drinking water all year long.

Self Cleaning Sediment FilterIdeal for Lake Water Applications

2” In/Out

3/4” - 1-1/2”In/Out

Models:Available Mesh Sizes:

1000 = 15 microns 500 = 30 microns 250 = 60 microns 140 = 104 microns 100 = 152 microns 60 = 254 microns 40 = 381 microns

Simple Installation, Easy to UseClear Cover Allows Quick View of Collected SedimentsMolded from UV Stabilized Weather Resistant MaterialsMaximum Operating Pressure: 150 psi Significant Filter Cartridge Life Expansion

Features► ►

►

►

►

105

Commercial and Industrial Filtration SystemsHigh Throughput Treatment for Most Water Quality Problems

Backwashable Iron and Arsenic Removal High Quality Water Softeners

Stainless Steel Commercial Quality Filter HousingsNon-Metallic Filter Housings for High Flow Rates

BackwashableIron, Manganese

andHydrogen Sulphide Removal Systems

Flow-MaxStainless Steel

JumboFilter Housings

Water Softener

BigBubbaHigh VolumeNon-Metallic

Filter Housingsand Cartridges

107

SPECIFICATIONS

Backwashable Air-Birm Iron Removal SystemAir Injector: Micronizer 1”Contact Tank: 8” x 35” (larger tanks available)Media Tank: 10” x 40” (larger tanks available) Off-Gas Valve: BraukmannBackwash Valve: Clack Media: 1 cu.ft Birm Additional Features: Bypass and sweat kit included

Distributed in Canada by Wyckomar Inc. 111 Malcolm Road, Guelph Ontario Canada N1K 1A8Phone 1-800-419-5162 Fax 519-763-6580 [email protected]


Filox Backwashable FiltersMineral Tank / Flow Rate / Media: 9” x 48” / 6 GPM /1 cu.ft

10” x 54” / 9 GPM / 1.5 cu.ft16” x 65” / 24 GPM / 4 cu.ft

Media: Filox Non-Chemical Oxidizing Media Additional Features: No Chemicals Needed for

Regeneration, No Contact TankGravel-free Mineral Tank

Clack Water SoftenerAir Injector: Micronizer 1”Media Tank: 10” x 42” (other sizes available)Brine Tank: 16” x 16” x 36” (other sizes available) Valve: ClackMedia: Brine Additional Features: Bypass and tail kit included

Flow-Max Stainless Steel Jumbo Filter HousingsMaterial: 304L stainless steel (316L available)Pressure Rating: Up to 150 psi (10 bar)Temperature: Up to 250° F (121° C) Gaskets and Seals: Buna-N Finish: Poly-coat over stainlessPressure Drop: Initial Pressure drop < 1 psi Cartridge Types: Standard DOE cartridges

BigBubba Non-Metallic High Volume Filter HousingsMaterial: Glass Reinforced PPPressure Rating: Up to 125 psi (8.75 bar)Temperature: Up to 175° F (80° C) Gaskets and Seals: EPDM Maximum Flow Rate: 150 GPMPressure Drop: Initial Pressure drop < 5 psi Cartridge Types: Pleated (1A, 1, 5, 20, 50, 150 Micron)

108

Contents · Our UV systems have long been at home in the ... The Filaments and Arc in a ......

Documents

Transcript of Contents · Our UV systems have long been at home in the ... The Filaments and Arc in a ......