© Boardworks Ltd 2005 1 of 20 Graphic Products Materials These icons indicate that teacher’s...
-
Upload
marianna-francis -
Category
Documents
-
view
212 -
download
0
Transcript of © Boardworks Ltd 2005 1 of 20 Graphic Products Materials These icons indicate that teacher’s...
© Boardworks Ltd 20051 of 20
Graphic ProductsMaterials
These icons indicate that teacher’s notes or useful web addresses are available in the Notes Page.
This icon indicates that the slide contains activities created in Flash. These activities are not editable.
For more detailed instructions, see the Getting Started presentation.
© Boardworks Ltd 20051 of 20
© Boardworks Ltd 20052 of 20
Learning objectivesL
earn
ing
Ob
ject
ives
© Boardworks Ltd 20052 of 20
paper, card and board
plastics
modelling materials
inks
smart materials
fixatives.
To learn about the properties of a range of materials:
© Boardworks Ltd 20053 of 20
Paper is made from pulped wood. There are many different types.When you are selecting a paper, there are two main aspects you should consider:
Surface finish The finish of the paper or board is important to the overall look of a product once it has been printed. The finish affects the texture of the paper and the way it absorbs ink.
Weight All papers and boards have a weighting measured in g/m2
(sometimes written gsm). This is the weight in grams of one square metre.
Paper and boards
© Boardworks Ltd 20054 of 20
Most paper used in schools weighs about 80 g/m2. This is fairly thin.
Paper is usually classed as card when it weighs more than 220 g/m2.
Very thick card is called board. Board is usually made from more that one sheet (ply) of card. The thickness of board is sometimes gauged by the number of sheets it consists of.
The thickness of card and board can be measured in micrometers (or microns for short). Mountboard can be more than 1000 microns thick.
Paper, card and board
© Boardworks Ltd 20055 of 20
Anything weighing less that 220 g/m2 is classed as a paper. Complete the following table to identify a number of papers, their properties and their uses.
Types of paper
© Boardworks Ltd 20056 of 20
Anything weighing more that 220 g/m2 is classed as a card or board. Complete the following table to identify a number of cards and boards, their properties and their uses.
Types of card and board
© Boardworks Ltd 20057 of 20
Uses of paper
© Boardworks Ltd 20058 of 20
Paper size
© Boardworks Ltd 20059 of 20
There are two categories of plastic:HEATED
SHAPED
COOLED
At a molecular level, a thermosetting plastic has more bonds holding it together.
A thermoplastic has fewer bonds, allowing the plastic to be reshaped several times.
HEATED
SHAPED
COOLED
BURN
Thermosetting plasticsA thermosetting plastic can only be heated and shaped once. If you try to heat a thermosetting plastic again, it simply burns.
ThermoplasticsA thermoplastic can be repeatedly heated and shaped.
Plastics
© Boardworks Ltd 200510 of 20
Graphic products mainly use thermoplastics. Thermoplastics are more versatile because they can be reshaped. They can also be recycled, making them ideal for use in packaging.
There are many different types of thermoplastic but we are only going to concentrate on the following four:
PVC (polyvinyl chloride)A very versatile plastic that can be flexible or rigid.
PolystyrenesLight, cheap, easily shaped and dyed plastics.
PolyethylenesShatter-proof, lightweight plastics, used for drinks bottles.
AcetateA flexible, transparent plastic that is easily cut.
Thermoplastic
© Boardworks Ltd 200511 of 20
Thermoplastic
© Boardworks Ltd 200512 of 20
Plastic
© Boardworks Ltd 200513 of 20
When you need to manufacture a three-dimensional model, there are a range of materials available to you.
You need to pick the one best suited to the job in hand. The next slide has more information about the properties of some of these materials.
corrugated sheets (plastic and card)
foam board.
Sheet modelling materials, such as:
clay
modelling foam (styrofoam).
Other modelling materials like plaster bandage.
Block modelling materials, such as: Sheet materials can be glued together to make 3D shapes.
Modelling materials
© Boardworks Ltd 200514 of 20
Modelling materials
© Boardworks Ltd 200515 of 20
Once you have made your basic model, it will often need a ‘finish’ to give it colour or an appropriate texture.
The finish you need to use depends on the modelling material you chose.
Corrugated sheet (paper)
Modelling foam
Clay
Plaster bandage
Foam board
Water-based paint
Filler and water-based paint
Glaze or solvent-based paint
Acrylic or other solvent-based paint
Corrugated sheet (plastic)
Modelling finishes
© Boardworks Ltd 200516 of 20
For an ink to function properly it must remain in a liquid state so that it can be applied easily. However, once on the surface of the product it must dry as quickly as possible.
Pigment + Vehicle = InkInk is made up of a solid pigment that is dissolved or suspended in a liquid, called a vehicle. Once applied to the surface, the vehicle is either absorbed or evaporates, leaving the pigment behind.
Pigments
© Boardworks Ltd 200517 of 20
Some materials are referred to as SMART materials – these materials have additional, and often surprising, properties.
For example…
These pigments can be used in products like clothing for
aesthetic, as well as functional
purposes.
E.g. A child’s plastic spoon can
be made that changes colour
from red to yellow if the food is too
hot.
Thermochromic ink and pigments change colour when the environment becomes either hotter or colder.
THERMOCHROMIC INK
Smart pigments
© Boardworks Ltd 200518 of 20
You can present a final design through a presentation drawing.
You can also fix work with hairspray.
Presentation drawings done in soft pencils or pastels must have a fine layer of fixative sprayed onto them to stop the drawing from smudging on contact.
Depending on the medium used, the image may need fixing. This term does not mean to fix something that is broken – it means to apply a fixative to protect the surface of the image.
Fixatives
© Boardworks Ltd 200519 of 20
Encapsulation (also known as laminating) is when an image is put between two layers of plastic.
The plastic is heat sealed around the edges, and to the image.
You can also get cold laminate. The glue is covered by a liner which is peeled off when it is applied to the image
Encapsulation
HOT LAMINATE
COLD LAMINATE
Lamination creates a tough, durable, high gloss finish.
© Boardworks Ltd 200520 of 20
Key pointsK
ey p
oin
ts
© Boardworks Ltd 200520 of 20
There are many different types of paper and card. The correct type must be selected for each graphic product.
Plastics can be either thermoplastics or thermosetting plastics. The properties of plastics vary greatly.
There are many different types of modelling material.
Inks consist of pigment and vehicle.
There are a growing number of smart materials on offer.
Fixatives and encapsulation can be used to preserve images.