© 2010 Delmar, Cengage Learning Chapter 4: Creating Animation.
© 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.
-
Upload
clarence-ford -
Category
Documents
-
view
237 -
download
0
Transcript of © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.
![Page 1: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/1.jpg)
© 2012 Delmar, Cengage Learning
Suspension System Service
Chapter 64
![Page 2: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/2.jpg)
© 2012 Delmar, Cengage Learning
Objectives• Diagnose suspension system problems• Service suspension system components• Describe suspension system repairs• Replace Macpherson struts• Replace suspension bushings
![Page 3: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/3.jpg)
© 2012 Delmar, Cengage Learning
Introduction• This chapter emphasizes the diagnosis and
service of suspension system parts– Commonly performed chassis diagnosis and
repair procedures
• Suspension parts in good condition and properly aligned are subjected to two forces– Car weight on springs and road force of on tires
• Suspension parts take a large amount of abuse– Forces transmitted through the suspension parts
cause wear over time
![Page 4: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/4.jpg)
© 2012 Delmar, Cengage Learning
Diagnosing Suspension System Problems
• Considerations– Carefully question a customer about symptoms
– Entire system IS affected when one part becomes worn
– Spring sag is normal and occurs with the passage of time
– Check all ball joints and bushings for looseness
![Page 5: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/5.jpg)
© 2012 Delmar, Cengage Learning
Shock Absorber Service• Shock absorbers can be functioning poorly
before obvious signs of failure– Defective shock absorber can cause tire “hop”
– Shock can be defective because it is leaking or physically damaged
– Some OE shock absorbers will still work well after 50,000 miles
![Page 6: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/6.jpg)
© 2012 Delmar, Cengage Learning
Testing a Shock• Perform a visual inspection of the shock
– Inspect shock mounts and rubber cushions
– Check for fluid leaks
– Outside of shock is damaged: replace both shocks
– Rubber bump stops show signs of contact: shock could be damaged
– Check shock mounts
– Air shock: sometimes fail when it gets a hole in its rubber bladder
– Gas shock has lost its gas charge: no longer will expand
![Page 7: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/7.jpg)
© 2012 Delmar, Cengage Learning
Macpherson Strut Service• Macpherson strut shock fails
– Common repair procedures• Replace entire assembly• Install a strut cartridge
• Some struts are easily removed at the bottom by removing two bolts– Spring compressor is used to compress the coil
spring
– Some struts can be serviced with a shock cartridge
![Page 8: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/8.jpg)
© 2012 Delmar, Cengage Learning
Inspect the Upper Strut Bearing
and Install the Coil Spring• Inspect the upper strut bearing – Inspect condition of upper strut bearing while
strut is disassembled
• Install the coil spring– Install coil spring and tighten locknut
– Be sure both ends of spring are correctly seated before removing compressor
![Page 9: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/9.jpg)
© 2012 Delmar, Cengage Learning
Reinstall the Strut Assembly• Reinstall in same position as before
– Wheel alignment may be needed after strut replacement
– Brakes will need to be bled if brake caliper was disconnected
![Page 10: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/10.jpg)
© 2012 Delmar, Cengage Learning
Suspension Bushing Service• Bushing characteristics
– Made of synthetic rubber
– Prone to heat damage
– Should not be lubricated
– Deteriorate with age
– Removed by pressing or driving them out
![Page 11: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/11.jpg)
© 2012 Delmar, Cengage Learning
Strut Rod Bushing Service and Stabilizer Bar Service
• Strut rod bushing service– Remove the fasteners
– Most bushings have a center spacer
• Stabilizer bar service– Inspect bushings at both ends of stabilizer bar
– Replace any bushings that are cracked, worn, or weathered
![Page 12: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/12.jpg)
© 2012 Delmar, Cengage Learning
Spindle Service• Replace a steering knuckle or spindle that is
damaged– If a wheel bearing fails it can wear or heat the
spindle• Changes the metallurgy of the spindle and it must
be replaced
• Damage from a collision will be noticed during SAI alignment angle check
![Page 13: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/13.jpg)
© 2012 Delmar, Cengage Learning
Ball Joint Service• Important points and considerations
– Ball joints are relatively trouble-free
– Feel around outside of boot and look for tears
– Always check specifications
– Load-carrying ball joint usually has some movement when unloaded
– Determine whether ball joint is a load carrier or follower
![Page 14: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/14.jpg)
© 2012 Delmar, Cengage Learning
Measuring Ball Joint Wear• Important points and considerations
– Check manufacturer's recommended procedures before checking ball joints
– For an accurate check: ball joint must not support weight of vehicle
– Follower joint should be checked at same time loaded ball joint is unloaded for testing
• To check follower ball joint for movement: unload joint and try to move tire back and forth
– Some ball joints have wear indicators
![Page 15: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/15.jpg)
© 2012 Delmar, Cengage Learning
Separating Tapered Connections
• Loosening the tapered connection on a ball joint can be accomplished using a large hammer– Remove cotton pin from ball joint nut and loosen
nut
– Position vehicle so coil spring is pushing control arm away from ball joint
– Use hammer to pound sharply on steering knuckle on outside of taper
![Page 16: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/16.jpg)
© 2012 Delmar, Cengage Learning
Replacing a Ball Joint• Characteristics
– Some original equipment ball joints are fastened to control arm with rivets
– Ball joints can also be pressed or threaded into hole in control arm
– Some pressed-fit ball joints have a spot weld that hold them in place
![Page 17: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/17.jpg)
© 2012 Delmar, Cengage Learning
![Page 18: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/18.jpg)
© 2012 Delmar, Cengage Learning
Coil Spring Service• Characteristics
– Coil spring will rarely break unless it has been constantly overloaded or has a stress raiser
– Incorrect ride height affects wheel alignment angles, camber, toe, SAI, and scrub radius
– A vehicle that is too low cannot be aligned properly
![Page 19: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/19.jpg)
© 2012 Delmar, Cengage Learning
Adjusting Spring Height and Coil Spring Replacement
• Adjusting spring height– Correct ride height must be restored prior to
alignment
– Coil springs must be replaced when they have sagged beyond specifications
• Coil spring replacement– Replaced in front or rear pairs
– Replacement springs must be of the same kind
![Page 20: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/20.jpg)
© 2012 Delmar, Cengage Learning
SLA Coil Spring Replacement• Major considerations
– During a coil spring replacement: only lower ball joint needs to be removed
– Spring seats must be accurately aligned
– Torsion bar adjusting bolt must be loosened before removing torsion bar
– Leaf spring problems include broken leaves, spring sag, and differences in ride height
![Page 21: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/21.jpg)
© 2012 Delmar, Cengage Learning
Wheel Alignment• Required after suspension repairs
– Repositions suspension components• Car will be safe to drive and will go straight without
unusual tire wear
• Remember to torque bolts that go through bushings only after vehicle is resting on its tires
![Page 22: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/22.jpg)
© 2012 Delmar, Cengage Learning
Electronic Suspension Service• Electronic suspension system problems
– Often related to mechanical failures– Electrical failures can also occur in the air system
• Wiring connections – Common source of problems
• Electronic failures – Set a diagnostic trouble code and cause
instrument panel light to flash
• Electronic suspension systems– Several sensors
![Page 23: © 2012 Delmar, Cengage Learning Suspension System Service Chapter 64.](https://reader033.fdocuments.in/reader033/viewer/2022061612/56649d9c5503460f94a85848/html5/thumbnails/23.jpg)
© 2012 Delmar, Cengage Learning
Electronically Controlled Shock Absorbers
• Some shock absorbers are electronically controlled– Remove actuator: squeeze plastic retainers to lift
motor from top of strut
• Diagnosing actuator system– Wiring color codes and specific instructions
required