Post on 28-Apr-2015
SP716 SP916 Service Manual
SP716/SP916
1 / 20
TABLE OF CONTENTSWARNING--------------------------------------------------------------------------------------3 A. IMPORTANT SAFETY INSTRUCTION--------------------------------------3 B. SPECIFICATIONS ---------------------------------------------------------------------4 C. TIMING CHART------------------------------------------------------------------------6 D. ADJUSTMENT PROCEDURE-----------------------------------------------------8 E. TROUBLE SHOOTING HINTS---------------------------------------------------9 F. BLOCK DIAGRAM------------------------------------------------------------------- 13 G. EXPLODED DIAGRAM-------------------------------------------------------------14 H. SCHEMATIC DIAGRAM-----------------------------------------------------------16 I. PCB LAYOUT DIAGRAM----------------------------------------------------------17
SP716/SP916
2 / 20
WARNINGTo prevent from fire or shock hazard,do not expose monitor to any rain or any form of water.High voltage is inside the monitor so please do not remove the back cover of the cabinet if you are not a qualified monitor engineer.Contact the local dealer or the nearest Proview branch office if you need help.
A. IMPORTANT SAFETY INSTRUCTIONPrior to using this service manual,please ensure that you have carefully followed all the procedures outlined in the user's manual for this product. 1. Read all of these instructions. 2. Save these instructions. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning.Do not use liquid cleaner or aerosol cleaner, use a damp cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart,stand or table.The product may fall,causing serious damage to the product. 7. Slots and openings in the cabinet and the back or bottom are provided for ventilation,to ensure reliable operation of the product and to protect it from overheating.Those openings must not be blocked or covered.The openings should never be blocked by placing the product on a bed,sofa, rug, or other similar surface.This product should not be placed in a built-in installation,since proper ventilation is provided. 8. This products should be operated with the type of power source indicated on the marked label. If you are not sure of the type of power is available, consult with your dealer or local power company. 9. This product is equipped with a 3-wire grounding type plug,a plug having a third (grounding) pin.This plug will only fit into a grounding-type power outlet.This is a safety feature.If you are unable to insert the plug into the outlet,contact your electrician to replace your obsolete outlet.Do not damage the purpose of the grounding-type plug. 10. Do not allow anything to rest on the power cord.Do not locate this product where persons will walk on the cord. 11. Never push any kinds of objects into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.Never spill any kinds of liquid on the product. 12. Do not attempt to service this product yourself,as opening or removing covers may expose you to dangerous voltage points or other risk.Refer all servicing to service personnel. 13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions. a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally,when the operating instructions are followed.Adjust only those controls involved in the operating instructions ,since improper adjustment of other controls may result in damage and will often require extra work by a qualified technician to restore the product to normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance,indicating a need for service.
SP716/SP916
3 / 20
B. SPECIFICATIONSSP716Panel General Specification Screen Diagonal Model Name Active Display Area Pixel Pitch Number of Colors View Angle Horizontal Vertical Luminance of White Contrast Ratio (Typical) Maximum Resolution Recommend Resolution Synchronization Range Horizontal Vertical Pixel Rate User Control OSD Function 17 TFT CMO M170E5-P01 337.92(H) 270.34(V) mm 0.264(H) x 0.264(V) mm 16.2M colors +/-70 degree +/-60 degree Typical 250cd/m(Min.) 450:1 1280 x 1024 @ 75Hz 1280 x 1024 @ 75Hz 30 80 KHz 60 75 Hz 135 MHz 5 Key Switch Auto, Brightness, Contrast, H-position, V-position, H-size, Phase, Reset, Color selection (R, G, B, cool, warm), OSD , Language, Exit. 90 264 Vac 60 / 50 Hz 48 W (max.) 15 Pin D-Sub Type; D-Sub: Analog R.G.B. , 0.7Vp-p / 75 Ohms TTL level,positive or negative polarity Cool / Warm / user mode 378.4x382x192 (mm) 3.8 kg -5 / + 15 degree 48W 3W 3W
Power Source Power Consumption Connection Type Input Signal Video Sync. Color Temperature Dimension (WxHxD) Monitor Weight Base Operation Tilt Power Saving ON STAND BY OFF Signal Connector Pin Assignment D-SUB Pin No.
1. Red Video 2.Green Video 3.Blue Video 4.GND 5.Self Test Sound Output No Audio
6. Red Ground 7. Green Ground 8. Blue Ground 9. VGA +5V 10. Sync. GND
11. GND 12. SDA For DDC2B 13. H-sync. 14. V-sync-DDC1 15. SCL For DDC2B
SP716/SP916
4 / 20
SP916Panel General Specification Panel Model Screen Diagonal Active Display Area Pixel Pitch Number of Colors View Angle Horizontal Vertical Luminance of White Contrast Ratio (Typical) Maximum Resolution Recommend Resolution Synchronization Range Horizontal Vertical Pixel Rate User Control OSD Function Hannstar HSD190ME12-A00 19 TFT 376.32mm (H) x 301.056mm (V) 0.294(H) x 0.294(V) mm 16.2M colors +/-70 degree -60/+70 degree Typical 250cd/m(Typical) 500:1 1280 x 1024 @ 75Hz 1280 x 1024 @ 75Hz 30 80 KHz 60 75 Hz 135 MHz 5 Key Switch Auto, Brightness, Contrast, H-position, V-position, H-size, Phase, Reset, Color selection (R, G, B, cool, warm), OSD , Language, Exit. 90 264 Vac 60 / 50 Hz 50 W (max.) 15 Pin D-Sub Type; D-Sub: Analog R.G.B. , 0.7Vp-p / 75 Ohms TTL level,positive or negative polarity Cool / Warm / user mode 426.4x 417x210 (mm) 4.6 kg -5 / + 15 degree 50W 3W 3W
Power Source Power Consumption Connection Type Input Signal Video Sync. Color Temperature Dimension (WxHxD) Monitor Weight Base Operation Tilt Power Saving ON STAND BY OFF Signal Connector Pin Assignment D-SUB Pin No.
1. Red Video 2.Green Video 3.Blue Video 4.GND 5.Self Test Sound Output No Audio
6. Red Ground 7. Green Ground 8. Blue Ground 9. +5V from PC 10. Sync. GND
11. GND 12. SDA For DDC2B 13. H-sync. 14. V-sync-DDC1 15. SCL For DDC2B
SP716/SP916
5 / 20
C . TIMING CHARTD Video B Sync. A E A: Period B: Active C: Sync Width D: Back Porch E: Front porch
C
Preset Modes
VGA 640X400
VGA 640X480
VESA 640X480
VESA 640X480
VGA 720X400
VESA 800X600
VESA 800X600
VESA 800X600
Dot Rate F.H A-period B-Active C-Syn D-Back Porch E-Front Porch F . V A-Period B-Active C-Syn D-Back Porch E-Front Porch H/V SYNC Interlaced
25.175MHz 31.469KHz 31.778us 25.422us 3.813us 1.907us 0.636us 70.087Hz 14.268ms 12.711ms 0.064ms 1.112ms 0.381ms
25.175MHz 31.469KHz 31.778us 25.422us 3.813us 1.589us 0.954us 59.941Hz 16.683ms 15.253ms 0.064ms 0.794ms 0.572ms
31.500MHz 37.861KHz 26.413us 20.317us 1.270us 3.810us 1.016us 72.810Hz 13.734ms 12.678ms 0.079ms 0.528ms 0.449ms
31.500MHz 37.500KHz 26.667us 20.317us 2.032us 3.810us 0.508us 75.000Hz 13.333ms 12.800ms 0.080ms 0.427ms 0.026ms
28.322MHz 31.469KHz 31.777us 25.422us 3.813us 1.907us 0.635us 70.087Hz 14.268ms 12.711ms 0.064ms 1.112ms 0.381ms
36.000MHz 35.156KHz 28.444us 22.222us 2.000us 3.556us 0.666us 56.250Hz 17.778ms 17.067ms 0.057ms 0.626ms 0.028ms
40.000MHz 37.879KHz 26.400us 20.000us 3.200us 2.200us 1us 60.317Hz 16.579ms 15.840ms 0.106ms 0.607ms 0.026ms
50.000MHz 48.077KHz 20.800us 16.000us 2.400us 1.280us 1.12us 72.188Hz 13.853ms 12.480ms 0.125ms 0.478ms 0.77ms
NON
NON
NON
NON
NON
NON
NON
NON
SP716/SP916
6 / 20
Preset Modes
VESA 800X600
VESA 1024X768
VESA 1024X768
VESA VESA VESA 1024X768 1280X1024 1280X1024
Dot Rate F.H A-period B-Active C-Syn D-Back Porch E-Front Porch F . V A-Period B-Active C-Syn D-Back Porch E-Front Porch H/V SYNC Interlaced
49.500MHz 65.000MHz 75.000MHz 78.750MHz 108.00MHz 135.00MHz 46.875KHz 48.363KHz 56.476KHz 60.023KHz 63.98KHz 79.976KHz 21.333us 16.162us 1.616us 3.232us 0.323us 75.000Hz 13.333ms 12.800ms 0.064ms 0.448ms 0.021ms 20.677us 15.754us 2.092us 2.462us 0.369us 60.004Hz 16.666ms 15.880ms 0.124ms 0.600ms 0.062ms 17.707us 13.653us 1.813us 1.920us 0.321us 70.069Hz 14.272ms 13.599ms 0.106ms 0.513ms 0.054ms 16.660us 13.003us 1.219us 2.235us 0.203us 75.029Hz 13.328ms 12.795ms 0.050ms 0.466ms 0.017ms 15.630us 11.852us 1.037us 2.296us 0.444us 60.020Hz 16.661ms 16.005ms 0.047ms 0.594ms 0.016ms 12.504us 9.481us 1.067us 1.837us 0.119us 75.025Hz 13.329ms 12.804ms 0.038ms 0.475ms 0.013ms
NON
NON
NON
NON
NON
NON
SP716/SP916
7 / 20
D. ADJUSTMENT PROCEDUREITEM Program Menu.
Test Meter Test Point Pattern
Operation
Check Value
Power supply
Check A
Digital Voltmeter CON 001 Crosshatch Pattern (1280x768, 60Hz)
220Vac 1. Plug power cable into the LCD monitor directly. 2. Make sure the voltage of the power plug (CON001) 0.2V on the Power Board to the value shown at right.
Power Saving Wattmeter Check PC or Pattern
B
generator Crosshatch Pattern (1280x768, 60Hz)
1. Unplug the signal cable into the monitor. 2. Turn the power switch of the monitor ON. 3. Check monitor power indicator light up blue flashing every other second. 4. Make sure the wattmeter value shown at right. 5. OSD will be display NO SIGNAL Picture.
3W
Into Factory PC or Pattern mode generator Crosshatch Pattern C (1280x768, 60Hz)
1. Hold Down key,then turn the power switch of the monitor off. 2. Hold Up key,then turn the power switch of the monitor on. 3. You can enter factory adjustment mode.
Auto mode Check D
PC or Pattern generator Crosshatch Pattern (1280x768, 60Hz)
1.Press and release the Auto key to adjust display mode to its utmost performance according to VGA setting.
White Balance Adjust E
PC or Pattern generator White Pattern (1280x768, 60Hz)
1. Move the OSD to the COLOR mode (AUTO COLOR). 2. set color is Cool using the OSD,Check the value shown at right. Y = 20020cd/m^2 x = 0.2830.02 y = 0.2970.02 3. set color is Warm using the OSD,Check the value shown at right. Y = 20020cd/m^2 x = 0.3130.02 y = 0.3290.02
OSD F Language Setting
PC or Pattern generator
1. Move the OSD to the OSD setting mode 2. Move the OSD to the LANGUAGE mode. 3. You can choose one of the language you need.
SP716/SP916
8 / 20
E . TROUBLE SHOOTING HINTSNo Display ( Black )
LED ON ?
NO
Power Supply ?
NO
Change power board
YES
YES
Push the power ON/OFF switch
LED Color change ?NO
YES
Back light ON?NO
YES
To Step 2
Check main board U5/Pin24
Check theCN1/Pin1,2 ofHigh Voltage !
power board Make sure the connection of power board is fine
Hi / Lo under push power sw?YES NO
+12V ?
NO
YES NO
To Step 2 A Check Power board
Display ?
YES
B
Nice Job !
SP716/SP916
9 / 20
A
B
Check the connection of CON1 cable
NO Hi / Lo under push power sw?
Change the main board
YES
Display ?YES
Change the power board
NO
Nice Job ! Display ?YES
Change the main boardNO
Nice Job !
To Step 2
Check the main board 12V input?
NO
Check F1
YES NOCheck the main board +5.0 V ?
Check I1,I2
YES
C
SP716/SP916
10 / 20
C
Check the main board 3.3V input ?YES
NO
Check I2
Check 2.5 V Input
NO
Check I1
YES
NOCheck H/V input Signal ?
Check U3/Pin37,38
YES
Display ?
NO
Change Signal Cable
YES
Nice Job !
SP716/SP916
11 / 20
No display (White)
Check the main board 5V ?
NO
Check I1,I2
YES NO
+3.3V ?
Check I2
YES
NO
H/V Input Signal ?YES
CheckU3/Pin37,38
Display ?
NO
Change Signal Cable
YES
Nice Job !
SP716/SP916
12 / 20
F. BLOCK DIAGRAMAUDIO IN(OPTION) Right Left
VGA IN
A/D_BOARD
LCD Panel Right Left
R G B Hsync Vsync SDA SCL
R G B
INTERFACE Hsync Vsync SDA SDA Bri control KEY Right Left ON/OFF DATA&CLK&VCC DATA&CLK&VCC
CONTROL BOARD
Power Board CCFL 5V 12V Bri control ON/OFF AUDIO OUT(OPTION) 220/110V Left Right SPEAKER
KEY
SP716/SP916
13 / 20
CCFL
12V
5V
G. EXPLODED DIAGRAM
SP716/SP916
14 / 20
SP716/SP916
15 / 20
H. SCHEMATIC DIAGRAM
SP716/SP916
16 / 20
5
4
3
2
1
D
D
TOP LEVEL1. S1:THE FIRST VERSION OF THE COST DOWN MODEL,MSTAR SOLUTION 2.change note:audio schematic add D13D2power schematic add R4C101 change TC5C C
3.DVI schmatic add R8,R12.power schmatic add R18.
B
B
APPROVE BYA
CHECK
BY
PREPARE BYA
200-100-M713I-ETitle
MSTAR COSTDWON(DVI_I PIGTAIL) LVDS&RSDS OUTSize Document Number Custom Date:5 4 3 2
Rev
Tuesday, June 28, 2005
TOP LEVEL
Sheet1
1
of
7
E
5
4
3
2
1
+5VD11 D12 C1 D4001 D4001 Changed in 2004.8.30 Q1 C3 0.1uF I1
VCC2V5
To InverterD
BL_CTRL
R1
33K VCC5V
3 1
VIN ADJ
VOUT TAB
2 4TC1 47uF/25V C2 0.1uF
VCC2V5
4
3
AIC1084-18CE
1 R2 2MMBT3904 R39 0 R5 Q2
4.7K
BKLT_EN
6 VCC3V3_PANEL R3 0R VCC3V3
D
0.1u
BRT_LEVEL C5 1u
3
VCC5V 1K Added by lotuschou 20041111
+5VC4 4 0.1uF
I2
3 1
VIN ADJ
VOUT TAB
2 4TC2 47uF/25V C6 0.1uF
VCC3V3
4,5,6
1 R6 2MMBT3904
100K
BKLT_ADJ
AIC1084-33CM
+5V
L1 BEAD
VCC5V
+12VR7 NP R9
1
C7 S1 0.1uFC
3
C
NP Q3 NP
6 PANEL12V_EN VCC3V3_PANEL
NP
1 2
NP U1 100
2
R11
R18
R10
Changed 2004.9.10
VLCD12V
S2
2CN1 VCC5V BL_CTRL BRT_LEVEL S3
1R13 22K
1 2 3 4
S1 G1 S2 G2
D1 D1 D2 D2
8 7 6 5
VLCD C11 0.1uF
C9 0.1uF(NC)
HEADER5X2B
R16 6 F1 24V/5A PANELVCC_EN 4K7
1C14
3
10 9 8 7 6 5 4 3 2 1
2FB1 1206
1
Si9933-SO8(9435) R4 100
ADD R4 AND R18+5V +12VS4
+ TC4 220uF/25V
MLB-201209-0220P-N2 C15 0.1uF
1
2
2+ TC3
1C13 R14 1K
C12 R15 0.1uF 100K(NC)
C0603
220uF/16V 0.1uF
Q4
F1A 125V/5A
0.1uF
+12VMLB-201209-0220P-N2
2
MMBT3904
B
1
1
1
1
FB3 1206
1
1
1
2
+ TC6 220uF/25V
C17 0.1uF
C0603
APPROVE BYA
CHECK
BY
PREPARE BYA
200-100-M713I-ETitle
MSTAR COSTDWON(DVI_I PIGTAIL) LVDS&RSDS OUTSize Document Number Custom Date:5 4 3 2
1Rev of 7
Tuesday, June 28, 2005
POWER
1
Sheet1
2
E
5
4
3
2
1
R28 DDC5V R20 R19 SCL_D1 SDA_D1 R26 R27 33 33 10K 10K DDC_CLK DDC_DAT DDC_CLK DDC_DAT 6 B 6 G R R211 33 33 R212 D6 ESD D5 ESD U2 1 2 3 4 NC NC NC GND AT24C21 VCC VCLK SCL SDA 8 7 6 5 DDC5V R21 10K R8 NC DDC5V DCC5V 2 3 3 D7 BAV99 D8 BAV99 DCC5V 2 D9 BAV99 DCC5V 2 3 VGA_DDC5V FB4 FB5 FB6 SBK160808T-300Y-S SBK160808T-300Y-S SBK160808T-300Y-S R32 75_1% C24 NC R34 R31 R33 R29 75_1% C20 NC R30
20
C19
47nF
BIN
4
47
C21
47nF
GNDB
4
D
20
C22
47nF 1000pF
D
GIN SOG
4 4
470 C23
47
C25
47nF
GNDG
4
6
DDC_DAT1
DDC_CLK1
6
C80 1
C81 1
C82 1 R36 75_1% C30 NC
R35
20
C26
47nF
RIN
4
100
DVI_DDC5V U6 1 2 3 4 NC NC NC GND AT24C21 VCC VCLK SCL SDA 8 7 6 5 10K 100 DDC_CLK DDC_DAT R210 R12 NC
0.1uF
0.1uF VCC5V
0.1uF
ADD R8 AND R12DVI_5V DDC5V DDC5V DDC5V DDC5V 3 1 D1 BAT54C 2
R37
47
C31
47nF
GNDR
4
C
C
HSYNC_IN VSYNC_IN ST_DET1 6 D3 5.6V D4 5.6V C84 20u C83 20u R23 10K
R17 R22 R24 2K2
100 100
HSYNC VSYNC
4 4
HPDET_D1 Q201 E 2N3906 B R201 3.3K D101 R204 2.2K R206 33K C C B B R205 3 2 1 CN5 Rout DATA0+ DATA0DATA1+ DATA1DATA2+ DATA2CLK+ CLK100K E Q202 2N3904 E R203 10K 6 DDC_WP C Q203 2N3904 R207 R208 3.3K B E 10K ESD Q204 2N3906 VGA_DDC5V VGA_DDC5V R209 33K/NC
R213 100
DVI_DDC5V DVI_DDC5V C
B+ R222 100 BG+ R223 100 GR+ R214 10R R215 10R R216 10R R217 10R R218 10R R219 10R R220 10R R221 10R B+ BG+ GR+ RCLK+ CLKR224 100 RCLK+ R225 100 CLK-
R202 33K/NC
B+
4
BG+
4 4B
1B
1
R U_GND L
GR+
4 4
1 DVI_5V R 1 L U_GND
2 4 6 8 HPDET_D1 10 SDA_D1 12 SCL_D1 14 GND 16 B 18 GND 20 G 22 GND 24 R 26 GND 28 CN2
1 3 5 7 9 11 13 15 17 19 21 23 25 27 PHD 2.0/90D
DATA2DATA2+ GND DATA1DATA1+ GND DATA0DATA0+ GND CLKCLK+ GND VSYNC_IN HSYNC_IN
RCLK+
4 4
CLK-
4
A
D23 BAV99 VCC5V
D24 BAV99 VCC5V 2
3
3
D25 BAV99 VCC5V
3
D26 BAV99 VCC5V
3
D27 MMBD7000 VCC5V
D28 BAV99 VCC5V
3
3
D29 BAV99
3
D30 BAV99 VCC5V
3
APPROVE BY2 1 2 C75 0.1uF 1 VCC5V 2 1
CHECK
BY
PREPARE BY
A
1
2
1
2
1
2
2
1
C70 0.1uF
C71 0.1uF
C72 0.1uF
C73 0.1uF
C74 0.1uF
1
C76 0.1uF
C77 0.1uF
200-100-M713I-ETitle
MSTAR COSTDWON(DVI_I PIGTAIL) LVDS&RSDS OUTSize Document Number Custom Date:5 4 3 2
Tuesday, June 28, 2005
VGA IN(DVI_ PIGTAIL)Sheet1
Rev 3 of 7
E
5
4
3
2
1
VAD
VPLL VDVI
VDPLL
VCC3V3 VPO VDD2V5 RA2 RA3 RA4 RA5 RA6 RA7 GA2 GA3 GA4 GA5 GA6 GA7 BA2 BA3 BA4 BA5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
FB7
VPO
PBY160808T-600Y-S TC7 10uF/16V C32 0.1uF C33 0.1uF C34 0.1uF C35 0.1uF C36 0.1uF C37 0.1uF C38 0.1uF
11 21 84 94 104 114 126 VDDP VDDP VDDP VDDP VDDP VDDP VDDP
MST TSU16AK/TSU56AKD
U3
AVDD_MPLL
AVDD_PLL
VDDC VDDC VDDC VDDC
AVDD AVDD
AVDD AVDD
18 87 97 117
55 65
35
45 51
53
3 3 3 3 3 3 3 3 3
RIN GNDR GIN GNDG SOG BIN GNDB HSYNC VSYNC
RIN GNDR GIN GNDG SOG BIN GNDB HSYNC VSYNC
63 62 60 59 61 58 57 37 38
RIN0 RIN0M GIN0 GIN0M SOGIN0 BIN0 BIN0M HSYNC0 VSYNC0
3 3 3 3 3 3 3 3C
R+ RG+ GB+ BCLK+ CLK- VDVI
R+ RG+ GB+ BCLK+ CLKR40 390_1%
40 41 43 44 46 47 49 50 52
R+ RG+ GB+ BCK+ CKREXT
C45 0.1uF
66 67
REFP REFM
NC/BA2 NC/BA3 NC/BA4 NC/BA5 NC/BA6 NC/BA7 NC/GA2 NC/GA3 NC/GA4 NC/GA5 LVA3P/GA6 LVA3M/GA7 LVACKP/NC LVACKM/NC LVA2P/RA2 LVA2M/RA3 LVA1P/RA4 LVA1M/RA5 LVA0P/RA6 LVA0M/RA7 NC/BB2 NC/BB3 NC/BB4 NC/BB5 NC/BB6 NC/BB7 NC/GB2 NC/GB3 NC/GB4 NC/GB5 NC/GB6 NC/GB7 NC/RB2 NC/RB3 NC/RB4 NC/RB5 NC/RB6 NC/RB7 NC/GPO0 NC/GPO1 NC/GPO2 NC/GPO3 NC/GPO4 DDC1_DAT/GPO7 DDC1_CLK/GPO8 NC NC/GPO9 NC/OCLK NC/ECLK OSP ESP BUS TYPE AD0/GPO6 AD1 AD2 AD3/GPO5 RDZ / SCL WRZ / SDA ALE / CS LVB2P LVB2M GNDC GNDC GNDC GNDC GNDP GNDP GNDP GNDP GNDP GNDP GNDP
88 89 90 91 92 93 98 99 100 101 102 103 106 107 108 109 110 111 112 113 124 125 128 1 4 5 8 9 12 13 14 15 16 17 22 23 24 25 83 82 81 80 79 28 29 118 119 120 121 76 75 6 30 77 78 31 71 70 69 122 123 C85 47PF AD0 AD1 AD2 AD3 C86 47PF
D
VDD2V5 VCC2V5 FB8
PBY160808T-600Y-S TC8 10uF/16V C39 0.1uF C40 0.1uF C41 0.1uF C42 0.1uF
LVACKP LVACKM
5 5
BA6 BA7 RB2 RB3 RB4 RB5 RB6 RB7 GB2 GB3 GB4 GB5 GB6 GB7 BB2 BB3
VCC3V3
FB9
VAD
PBY160808T-600Y-S TC9 10uF/16V C43 0.1uF C44 0.1uF
C
BB4 BB5 BB6 BB7
5 5 5 5
VCC3V3
6 HWRESET 6 INT R42 10KB
HWRESET INT
R41
47R 32 72 HWRESETZ INT
FB11
VDPLL
VCC3V3
FB10
VPLL
C48 10nF 7
R43
47 5 47
POL LOAD STV1 CPV OE
5 5 5 5 5
PBY160808T-600Y-S TC11 10uF/16V C47 0.1uF
PBY160808T-600Y-S TC10 10uF/16V C46 0.1uF
2
BKLT_ADJ VOLUME
BKLT_ADJ C49 22pF
73 74 33
LVB3P
PWM0 PWM1 XIN
R44
R51 52 62 63 CHANGE TO RN16
B
STV2 OCLK ECLK STH
5 5 5 5
R45 R46
VCC3V3
X1 14.318MHZ C52 C56 22pF 0.1uF 34 3 2 XOUT BYPASS AVSS_MPLL
47
FB12
VDVI
47 VCC3V3 6 R47 6 10K 6 6 R25 47R RDZ R38 47R WRZ R48 C87 47R ALE 47PF
ESP
5
C50 47P
C51 47P
PBY160808T-600Y-S TC12 10uF/16V C53 0.1uF C54 0.1uF
6 6 6
AVSS_MPLL
AVSS_PLL
AVSS AVSS AVSS
AVSS AVSS AVSS
LVB2M LVB2P 5 5
APPROVE BY
CHECK
BY
PREPARE BYA
68 56 64
36
54
39 42 48
10 20 85 95 105 115 127
19 86 96 116
A
200-100-M713I-EPin 6:LOW- SERIAL BUS Pin 6:HIGH- DIRECT BUSTitle
MSTAR COSTDWON(DVI_I PIGTAIL) LVDS&RSDS OUTSize Document Number Custom Date:3 2
Tuesday, June 28, 2005
MST SCALER1
Rev Sheet 4 of 7
E
5
4
5
4
3
2
1
CN3D
CN4 BB7 BB6 BB5 BB4 BB3 BB2 GB7 GB6 GB5 GB4 GB3 GB2 B0N B0P B1N B1P B2N B2P BG0N BG0P BG1N BG1P BG2N BG2P
4 4 4 4 4 4 4 4 4 4 4 4
BA7 BA6 BA5 BA4 BA3 BA2 GA7 GA6 GA5 GA4 GA3 GA2 LVB3P RA7 RA6 RA5 RA4 RA3 RA2
BA7 BA6 BA5 BA4 BA3 BA2 GA7 GA6 GA5 GA4 GA3 GA2 STV2-A DHS_TTL RA7 RA6 RA5 RA4 RA3 RA2 LOAD-A POL-A CPV-A STV1-A OE-A
FB0N FB0P FB1N FB1P FB2N FB2P FG0N FG0P FG1N FG1P FG2N FG2P FCLKN FCLKP FR0N FR0P FR1N FR1P FR2N FR2P STH LP POL HMS CLKV STV OE
4
4 4 4 4 4 4 4
STV2
4C
STH ESP
STH-A ESP
4
4 4 4 4 4
LOAD POL CPV STV1 OE
C60
C61
10pF(NC) 10pF(NC) R51 R52 R53 R54 R55 R56 R57 0(NC) 0(NC) 0(NC) 0(NC) 0(NC) 0(NC) 0(NC)
VLCD VLCD12V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
4 4 4 4 4 4 4 4 4 4 4 4
BB7 BB6 BB5 BB4 BB3 BB2 GB7 GB6 GB5 GB4 GB3 GB2
4 44 4 4 4 4 4
ECLK OCLKRB7 RB6 RB5 RB4 RB3 RB2
DEN_TTL BCLKN DCLK_TTL BCLKP RB7 RB6 RB5 RB4 RB3 RB2 BR0N BR0P BR1N BR1P BR2N BR2P
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30NC
D
JP1 RB4 RB2 LVB2P OCLK LVB3P BA6 BA4 BA2 LVACKP GA6 VCC_TEST RXO0+ RXO1+ RXO2+ RXOC+ RXO3+ RXE0+ RXE1+ RXE2+ RXEC+ RXE3+
4
LVB2P
4
VLCD
LVACKP
C59 0.1uF
1 3 5 7 9 11 13 15 17 19 21 23 25
2 4 6 8 10 12 14 16 18 20 22 24 26
RB5 RB3 LVB2M ECLK STV2 BA7 BA5 BA3 LVACKM GA7
RXO0RXO1RXO2RXOCRXO3RXE0RXE1RXE2RXECRXE3-
LVB2M
4
LVACKM
4
HEADER 12X2C
FOR RSDS INTERFACE 6 3/31 modify MCU_OD_EN MCU_OD_EN DHS_TTL LVB3P 4
(NC)6702-50-50P-R VCC3V3 FOR RSDS INTERFACE VCC3V3 R49 10K (NC) VCC_TEST FOR 19" FSC PANELB B
VCC3V3
2,4,6
R50 0(NC)
A
A
APPROVE BY
CHECK
BY
PREPARE BY
200-100-M713I-ETitle
MSTAR COSTDWON(DVI_I PIGTAIL) LVDS&RSDS OUTSize Document Number Custom Date:5 4 3 2
PANEL INTERFACETuesday, June 28, 20051
Sheet
5
of
7
E
Rev
5
4
3
2
1
MCU
MCU R64 R65
VCC5V R62 330 MCU 100 100 SCL1 SDA1 R68 LEDO 10K R69 1K 1 1K
VCC5V R63 330 POWER LED_O LED_G DOWN UP MENU AUTO RN10 22 CON1
C64 U4 .1u
1 2 3 4
A0 A1 A2 GND24C16 S9 2 S10
VCC WP SCL SDA
8 7 6 5
10K 10K R66 R67
LEDG R70
2
D
3
Q6 MMBT3904
VCC5V VCC3V3
1 1
1 2
MCU MCU R72 C65 .1u 10K 10K
MCU
Q7 MMBT3904
1 8 2 7 3 226 RN11 4 5 1 8 2 7 3 6 4 5D35 ESD
1 2 3 4 5 6 7 8
3
D
2
RN12
RN13
to KEY PAD
D34 D33 ESD D32 ESD D31 ESD ESD
4 3 2 1 4 3 2 1 5 6 7 8 5 6 7 8
10K
MCU TC14 10u/16V
U5 11.0592MHZ Y1
VCC
35 21 20 10
44
C66
22pF
EA/VP XTAL1 XTAL2 RESET
C68C
22pF
P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 NC P3.7/RD P3.6/WR PSEN ALE/P P3.1/TXD P3.0/RXD
43 42 41 40 39 38 37 36 24 25 26 27 28 29 30 31 12 19 18 32 33 13 11
HWRESET ALE RDZ WRZ AD0 AD1 AD2 AD3
4 4 4 4 4 4 4 4
C8 0.1uF
20050428 POWER DOWN UP MENU AUTO LEDO ST_DET1 4C
C69 .1u(NC)
R74 8.2K
D10 4 1N4148 INT SCL1 SDA1
14 15 16 17 2 3 4 5 6 7 8 9
INT0/P3.2 INT1/P3.3 T0/P3.4 T1/P3.5 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.78051-PLCC
VSS
2 PANEL12V_EN 2 PANELVCC_EN 3/31 modify 5 MCU_OD_EN 2 BKLT_EN 7 MUTE 3 DDC_WP 3 DDC_CLK1 3 DDC_DAT1
4 3 2 1 5 6 7 8
LEDG
RN14
RN15
5 6 7 8
10K
10K
4 3 2 1
MCU
4 3 2 1
RN5
RN6
4 3 2 1
22
DDC_DAT DDC_CLK
3 3
5 6 7 8
MCUB
5 6 7 8
10K
10K
VCC5V MCU CON2
1 2 3 4
B
RS232 debugNC
APPROVE BYA
CHECK
BY
PREPARE BYA
200-100-M713I-ETitle
MSTAR COSTDWON(DVI_I PIGTAIL) LVDS&RSDS OUT
Size Custom Date:5 4 3 2
MCU(SYNC&MYSON 512&MX)Tuesday, June 28, 2005 Sheet 6 of1
Document Number
Rev 7
E
LC Electronic Co., Ltd.
MODEL:AI-0088FAI-0088AF(Spec No.:01) Copy-right LIEN CHANG Electronic Enterprise Co., Ltd. No copy & disclosure is Allowed. All Right Reserved by LIEN CHANG.
29/239
LC Electronic Co., Ltd.
3
4
3
1
2
1
27
4
1284
1284
7
6
6
5 5
3 3
MODEL:AI-0088FAI-0088AF(Spec No.:01) Copy-right LIEN CHANG Electronic Enterprise Co., Ltd. No copy & disclosure is Allowed. All Right Reserved by LIEN CHANG.
30/239
I. PCB LAYOUT DIAGRAMMain Board
SP716/SP916
17 / 20
Control Board
Inverter + Power Board Top layer
SP716/SP916
18 / 20
Bottom layer
SP716/SP916
19 / 20
MEMO
SP716/SP916
20 / 20