Post on 31-Dec-2020
Page 1 TOOTAL COST OFF OWNERSHIPP
Page
The of oequwellundrepaof eown
Thistrea
e 2
objective ofownership oipment manl as fleet oper ownershiair costs are economic lifenership and o
s publicationts cost categ
f this publicaof a piece onagement anptimization. p and operatdescribed ine. Finally, a operating co
n does not ggories.
ation is to ouof heavy eqnd outline faFurther in tting costs. Son more detaispreadsheetsts.
go into deta
utline the cosquipment. Wactors affectthe documenome cost catil and modelt model is i
il on produc
st componenWe define tting productnt, we desctegories suchls are drawnncluded as a
ctivity calcul
TOTAL
nt when calche role of tion of a pieribe the varh as prevent to help undan example
ation in the
L COST OF OW
culating the tthe stakehoece of equiprious cost caive maintenaderstand theof how to
e same man
WNERSHIP
total cost olders in pment as ategories ance and e concept calculate
ner as it
Page 3 TOTAL COST OF OWNERSHIP
1. SCOPE 2. STAKEHOLDERS
• Equipment management • Business control
3. TOTAL COST OF OWNERSHIP (TCO) • Production (ton/h or m³/hr) • Cost ($/hr) • Unit cost ($/ton or $/m³)
4. PRODUCTION • Measurements • Equipment selection • Equipment matching • Fleet optimization
5. COST • Owning cost • Operating cost
6. ADVANCED DISCUSSION ON SELECTED TOPICS • Preventive maintenance cost • Repair cost
7. ECONOMIC LIFE • The Repair Reserve Model • The Classical Cost Minimization Model • Cumulative Cost Model • The Component Life Based Model
8. BUILDING AN OWNERSHIP AND OPERATING COST MODEL IN A SPREADSHEET
9. MAKING DECISIONS
• Buy, Rent or Lease? • In‐house vs. outsourced repair & maintenance
APPENDICES 1. Ownership and Operating Cost Template 2. Loader Production Estimator Template 3. TCO Template
Page 4 TOTAL COST OF OWNERSHIP
In most organizations, equipment forms a separate department, the role of which is to “provide the necessary equipment to the operations for a cost”. Inherently embedded in the organization is an objective which requires the equipment department, as well as the operations, to be profitable.
In some organizations with large operations, such as mines or quarries, the equipment department is the primary cost in the business, and therefore its efficient management is the key to the profitability of the organization. In the case of equipment rental houses, the objective is to be able to charge a profitable rental rate for the equipment while remaining competitive. This is also the case for an equipment dealer.
This document will focus on understanding cost for a piece of equipment. It does not describe ways to develop a chargeable rate.
The other dimension for the scope of this document is the focus on industry segment. Each industry (mining, quarrying, construction, utilities, forestry, material handling, waste handling, etc.) can be further broken down into specific work processes and machine applications. For example, in the case of mining, operations can be described as the processes of drilling, blasting, loading, hauling, crushing or processing, and material handling. There are other work processes or machine applications such as grading, paving, milling, compacting etc. which fall under the heading of construction or road building. In this document, we will concentrate on loading and hauling work processes.
Some of the questions this document will attempt to answer:
1. What is TCO in the context of mobile equipment and why it is important?
2. What are the components of TCO?
3. What factors affect the selection of a machine and hence its production?
4. What is the difference between purchase price and life cycle cost of a piece of equipment?
5. How do we estimate some of the parameters of TCO?
6. What do we mean by economic life of a machine and what models can help us understand the concept?
7. How do we build a simple spreadsheet model to understand production and cost?
Page 5 TOTAL COST OF OWNERSHIP
Heavy mobile equipment play a fundamental role in most industrial segments. They are necessary to complete work in an economic fashion and on a schedule. Yet they also comprise a large portion of the cost invested in such work. Mining and quarrying (ores, coal, aggregate and other minerals), construction (road, dam, tunnel, building etc.), utilities (gas lines, electricity grids, sewers), forestry work (tree harvesting, logging, timber handling, sawmill etc.), material handling (pallet, grains, construction materials), recycling or waste handling (transfer stations, landfills, scrap yards) are all examples of industries that are equipment intensive. Therefore the principles of equipment management are relevant in many cases. Although equipment management is not a required core competency in most operations, it plays a significant part in determining profitability and competitiveness. Therefore, the challenges within these organizations are twofold:
a) The equipment management personnel should be able to understand all aspects of equipment cost and how it relates to the business as a whole.
b) The general management should understand the intricacies that equipment managers face regarding equipment cost and decision‐making.
Consequently, this paper has been written with at least two stakeholders in mind: equipment managers and business controllers.
2.1 Equipment management Effective equipment management involves a variety of activities which can be grouped under two broad headings: development of equipment/fleet policy, and project management and optimization.
a) Development of policies involves setting guidelines and providing a central service to different company units (sites, projects, locations etc.). Therefore, activities are focused on long‐term strategies and big‐picture initiatives. A sample list of work processes involved under equipment policy could include capital and budget‐related decision‐making (asset management), asset monitoring (job costing), analysis of fleet performance (age, cost, reliability), ownership period and economic decisions (Repair, Replace, Rebuild, Retire), financing methods, and preventive maintenance programs and repair guidelines.
b) Project management and optimization, on the other hand, involves work processes that are limited to the life of a project. Therefore, these activities are focused on limited‐time strategies with clearly defined objectives. A sample list of work processes involved under project management and optimization could include machine selection, machine configuration, and fleet selection.
2.2 Business control The governing tenet of business control is based on profit and loss. However, not all aspects of business can be defined in black & white terms; most areas are gray. For example, with a piece of equipment the purchase price is the only aspect of cost that can be determined with certainty. All other costs, such as residual value, repair and maintenance, wear parts, etc, are – at best – guesses. Therefore, realizing the cost‐risk proposition in investment or other decisions, involves a basic understanding of various aspects of equipment‐related costs.
Page 6 TOTAL COST OF OWNERSHIP
Life cycle costs can be viewed as all the costs from cradle to grave in the life of a piece of equipment. Typically, life cycle costs can be divided into two broad categories: ownership and operating costs. Although equipment managers have long considered the concept of ownership and operating costs, it has taken a while to formulate a systematic approach to use this as a measure while selecting between alternatives.
Focusing only on initial cost does not necessarily produce the best alternative, as a piece of equipment with a lower purchase price could bleed the pockets due to high maintenance costs. However, comparing equipment only on operating costs does not facilitate the comparison of two alternatives similar in life cycle cost but differing in productivity. Thus the most recent step in this evolution is the use of total cost of ownership (TCO), which addresses both cost and productivity aspects. By moving to TCO, buyers are able to relate to profits rather than just cost. Although these considerations might seem obvious, it is interesting to note that only a small percentage of buyers‐sellers actually have the discipline and knowledge to perform this analysis. The difficulty has been in the collection and analysis of appropriate data. Three key elements of TCO are Production, Cost per Hour and Cost per Unit.
3.1 Production (ton/h or m3/h) Production per hour is the output of a single machine working by itself, or a fleet of machines working together. Depending on the type of work, production is typically calculated in a weight measurement (such as ton/hr) or a volume measurement (m3/h). Equipment capacity, configuration, loader‐hauler match, material to be moved, work schedule, haul distance and fleet size are some of the important factors which affect the production of a fleet of machines.
3.2 Cost ($/h) Cost per hour, including both ownership and operating costs will be dealt with in more detail in this document. Purchase price, residual value, economic life (ownership period), repair and maintenance policy and fuel consumption have a conspicuous effect on the cost per hour.
3.3 Unit Cost ($/ton or $/m3) Unit Cost is a result of the two elements above. To calculate Unit Cost, we divide the cost per hour value for a machine or a fleet by the corresponding production per hour. The beauty of Unit Cost is that it allows the comparison of dissimilar units. In other words, one can compare a small loader with small trucks against a big loader and big trucks. This is the definition of TCO. The objective is to move a desired amount of material at the lowest Unit Cost, or the lowest TCO.
$ / h $ton / h ton
TCO = =
Various organizations use the term TCO in different ways. In some cases, TCO refers only to the total cost per hour when the equipment is not involved in measureable production. For example, if a piece of equipment is a utility machine involved in cleanup or diverse support activity , it is not easy to quantify a cyclical activity and hence a production. However, this document will focus on cases where the equipment is involved in production, so Unit Cost will be used.
Page 7 TOTAL COST OF OWNERSHIP
Production refers to the output of a single machine or a fleet of machines working together. Typically we refer to loading production when we refer to the production of a single machine such as an excavator or a wheel loader. It is rather easy to determine the production of a loading unit simply by using the bucket capacity and average cycle time over a period of time. However, fleet production is a little more complicated: it is the throughput of the loading and the hauling units considered as one system. We will try to describe some of the aspects of production here.
4.1 Measurements The first step in understanding production is to understand the unit of measurement. Often, people focus on numbers and leave out the unit of measurements. The two standard units of measurements are volume (m3/h) and weight (ton/h). It is possible to translate one unit to the other using density. The relation between volume, weight and density is as follows:
WeightVolume
Density =
For example, the density of blasted limestone is 1600 kg/m3 or 1.6 ton/m3. Therefore a production measurement of 300 m3/h is the same as 480 ton/h. It is obvious that if the unit of measurement is left out, then the number by itself becomes meaningless.
Within the volume measurement, there exist two sub categories – bank volume and loose volume. In simple terms, bank state of a material is the virgin state of occurrence, or in the ground. For example, limestone as it occurs in nature is a rock formation. The loose state of a material is the broken state in which it is loaded or hauled in a piece of equipment. For example, when we drill and blast limestone, it breaks up into small pieces. The volume of limestone expands and voids (spaces) are created. The increase in volume is often referred to as the swell factor. The relation between bank, loose volumes and the swell factor is as follows:
Loose VolumeBank Volume
Swell Factor =
But even this definition is not enough, as loose volume can vary in different circumstances. A ton of limestone has one, bank, volume in the ground. It will have a different, loose, volume when blasted. It may have a different, loose, volume again after it is crushed and put in a stockpile. Therefore one must be aware of which state of condition is being used for calculation for any given material.
4.2 Equipment selection Equipment selection is a very complex subject and demands a detailed description. For our present purpose, we will focus on loading equipment. One question that is often asked is when to use an excavator and when to use a wheel loader? We present a simple table based on some job/project parameters. In addition to these parameters, there are several regional cultural as well as legal issues which determine the type of machine to be used on a project.
Page 8 TOTAL COST OF OWNERSHIP
Table 1: Factors used in selecting the type of loading equipment
Factor Excavator Wheel Loader
Sand, gravel, shot rock, earth Sand, gravel, well shot rock, earth(overburden) (overburden)
Digging envelope Below grade Above grade
Angle of swing 30 to 180 degrees ‘Y’ shaped travel pathSpace constraint Stationary Typically at least 1.5 machine lengthFloor condition Preferably flat and stable Preferably even and hard
Position vs. hauler Above; end‐load or side‐load Same level; side‐load only
Transport Travel speeds up to 6 km/h Travel speeds up 35 km/h
Best suited forTruck loading, difficult digging, sorting material, trenching, maintaining slopes
Truck loading, bin loading from multiple sources, digging loose(r) material, load & carry operations
Class of material
After selecting the type of equipment, it is important to understand the parameters that determine the machine size needed. Most often this is driven by production required for the job/project but may also depend on space limitations. Two machine‐related parameters important to calculate production are bucket capacity and average cycle time. Bucket capacity refers to the amount of material that can be carried by a bucket. By most standards, the capacity includes a measured heap of material over the water‐level surface of the bucket. Each material has a different slope characteristic that it can naturally sustain. For example, clay can sustain a higher slope compared to dry sand. Therefore, each of these materials has a different fill factor.
Consider an example job where the target production is 200 m3/h, and based on the site configuration and the material of loading, our best estimate tells us that we can do three loading cycles in a minute. This means that each cycle takes 20 seconds on average. The production of the loading unit can be calculated using the following equation:
It is possible to create a simple spreadsheet to determine the bucket size required to meet this production and hence the machine size.
60 x 60cycle time in seconds
x EfficiencyLoader
ProductionBucket capacity
= x
Table 2: Selecting equipment based on production (example)
EC220DL EC250DL EC300DL EC380DL EC480DL EC700CL1.2 m3 1.5 m3 1.9 m3 2.6 m3 3.2 m3 4.5 m3
Avg Cycle Time (sec)
Cycles per Hour*
20 180 216 270 342 468 576 81024 150 180 225 285 390 480 67527 133 160 200 253 346 426 59930 120 144 180 228 312 384 54033 109 131 164 207 283 349 49136 100 120 150 190 260 320 45039 92 110 138 175 239 294 41442 86 103 129 163 224 275 387
* 60 working minutes/ hour
Maximum Production Rate (m3/h)
Bucket Excavator Model
Page
In th
The dowperfincreif thsize thatmacmac
4.3Mateachtimestanhauwill loadThistime
4.4Assuhauidenhauhaudeep
It wit inTodawill vario
e 9
his example,
table showswnsize to 1.2form a senseases from 2he productiorequired to t this is a vechine utilizatchine size tha
3 Equipmtching the righ pass from e in the loanding still in lers to keep be idle. On
ded in 2 mins means three is acceptab
4 Fleet opume a job rlers. Also antify the righlers so that tlers was thaper analysis
as assumed dicates the may, with the provide the ous project a
all productio
s that we co m3 to achiesitivity analy20 to 24 secoon requiremeachieve the ry simple aption nor theat may be us
ment matght size hauthe loading ding area. Tthe loadingit busy. If a
ne rule of thnutes or lesse to five pasble in less de
ptimizatirequires a flssume that ht excavator the fleet is bat which kepa simple rule
Fleet Siz
that the loamost producunderstandilowest unit and machine
on values eq
ould use a 1eve a producysis. For exaonds, the maent is expectincreased p
pproach and e efficiency fsed for the jo
tching ler to the lotool is too sThe hauler ig area. Simila sufficient nhumb states , provided tsses by a whemanding app
ion leet of mach– based on for the job.
balanced. Thept the loadine of thumb c
Oe =
ding unit proctive solutioning of TCO wcost as the e related par
qual‐to‐or‐gre
1.5 m3 buckection of 216ample, if digachine’s prodted to increroduction cadoes not tafactor. This ob rather tha
oading tool imall, then this productivearly, having number of hathat in a mhere are eneel loader, oplications or
hines, for ethe product The next se old school ng unit busycan be used t
Overall cycleLoading ti
oduction detn but in no wwe know thatdesired objerameters.
eater‐than 2
et and achiem3/h. This tgging becomductivity wilease over timan also be deake into accomethod canan which is b
s important he hauler wie only whena big size loaulers is not
mass excavatiough hauleror four to six if there is a
xample an tion requiretep is to selof thought dy at all timesto determine
e time of theime of the h
termined theway does thist it is possiblective. This s
TOTAL
00 m3/h are
eve a producable also giv
mes difficult l be reducedme, then theetermined. Oount the denn be used toe the best m
to maximizeill spend a sun it is haulinoading tool t available, tion‐type jobrs to keep thpasses fromshortage of
excavator anments — weect the rightdictated thats. I Using te the hauler
e haulerhauler
e best fleet ps guarantee e to determiubject requi
L COST OF OW
e highlighted
ction of 270ves you the and the cy
d. On the othe appropriatOne must unnsity of the o get an idemachine for t
e fleet produbstantial amng material may requirethen the loadb, a hauler she loading tom an excavatohaulers.
nd some are have beent size and nut the right nuthis logic andfleet size.
production. the lowest uine the fleet ires the disc
WNERSHIP
blue.
m3/h or ability to ycle time her hand, e bucket derstand material, ea of the he job.
uction. If mount of and not e several ding tool hould be ool busy. or. More
rticulated n able to umber of umber of d lacking
Perhaps unit cost. size that ussion of
Page 10 TOTAL COST OF OWNERSHIP
The total cost of a machine comprises both ownership and operating components. However, by considering one composite value, we lose the opportunity to understand the inherent differences between these components and the factors that affect each.
Ownership cost, including depreciation and interest, can be viewed as fixed costs because they begin when the machine is purchased and end when it is sold. In between these two points, one must pay the ownership costs irrespective of the state of the machine. Whether it is working on a job, standing idle in the yard, or broken down for repairs, the ownership costs continue to accrue. On the other hand, operating costs, which include fuel, tires, maintenance and repair, and ground engaging tools, can be viewed as variable costs because they are incurred only when the machine is put to work. Thus, it makes a difference to the operating costs if the machine is working or standing idle. From this brief description, it is clear that there is a need to track owning and operating costs separately.
Owning and operating costs are equally important. Unfortunately, the only clearly visible cost for a piece of equipment is the purchase price; thus, the tendency can be to neglect the impact of other costs. A common metaphor on this subject is that of an iceberg. The tip of an iceberg, like the purchase price, does not divulge the true nature of the impact it can create. Operating costs associated with life cycle usage can have a bigger impact and often lie hidden from view. Therefore, it is prudent for equipment managers to delve deep into the subject of owning and operating costs to truly understand the impact of each.
Ownership cost is the cost of buying and keeping a machine in a fleet. It includes the purchase price, taxes, cost of borrowing capital to purchase the equipment, other financing costs, insurance, and the residual value at the time of sale. Almost all aspects of the ownership cost are related to accounting, not machine operation. A major part of the ownership cost is the depreciation, which is the difference between the original purchase price of the machine and the value at the end of its life. These accounting methods are related to time periods: ie. months or years. Yet ownership costs are commonly expressed in terms of cost per hour of operation. In this way, usage does have an impact on ownership cost (per hour). We need to divide it by the scheduled number of hours to be worked. Therefore, ownership cost per hour decreases as its scheduled time in the fleet increases.
Operating cost, on the other hand, begins as soon as you start the machine. There are several ingredients to operating cost. Typically, we can divide them into the following categories: fuel consumption, preventive maintenance, repair, tires and GET (ground engaging tools). Operating cost is a function of age, application, work environment and preventive maintenance policies. Like every machine ever invented, the cost of maintaining a piece of construction equipment increases with age (otherwise we could have kept the machine forever!). All moving and load bearing components have a physical life and need to be replaced at some time to maintain a tolerable level of performance, reliability and safety.
There is a point in the machine life when the ownership and operating costs combined produce the lowest total cost per hour. This is called the economic life, which is very different from the physical life of the machine. Determining the economic life of the machine can assist in equipment procurement as well as disposal. Also, it can provide the fleet management with an indication of the optimal duration of keeping the machine in the fleet.
Can the ownership and operating costs be considered as one? The answer is yes, but is qualified by the ubiquitous caveat ‘sometimes’. Consider the occasion when you rent a piece of machine, say a skid steer. When the rental house quotes you a rate of $600 a week, all your costs are
Page 11 TOTAL COST OF OWNERSHIP
included except fuel. Therefore, this cost represents both owning and operating components for the machine, as well as overhead costs and profit for the rental house. However, the difference between renting a machine and owning it is the same as between renting an apartment and owning it. Rental is subject to availability and price fluctuations; further, it does not offer an equity build‐up. On the other hand, ownership of a machine guarantees availability, price stability, tax benefits, and equity build‐up.
5.1 Owning costs The understanding of ownership costs parallels the development in financial transaction, accounting policies and risk management. If one was to review the evolution of the buying‐selling process for any type of equipment (capital goods), it is possible to see a pattern. Since the middle of the twentieth century, most purchase decisions were based only on the initial price. Then the cost of borrowing capital, inflation and return on investment introduced the finance cost into the procurement process. Purchase price, depreciation and taxation became the key components in calculating equipment cost. Subsequent to that, buyers wanted to shield themselves from the uncertainty of the residual values, especially when the equipment cost was not written down to zero. The next step in the evolution process was based on accounting and financial targets as well as cash flow. This development endorsed leasing as the preferred method where the focus moved from purchase price or residual values to monthly payments. Of course, the accounting principles and financial policies were different in different countries and therefore adapting the leasing program to the local business environment was critical.
The straight leasing programs were augmented with various flavors such as an optional buy‐out clause at the end of the period. Although lease payments created a certainty in the ownership component, the operating component of the cost was still subjected to uncertainties. In addition to this, most buyers realized that the lease programs did not necessarily produce the lowest cost. In reality, the buyers were paying more to reduce their risk or exposure. Those buyers who developed in‐house competency in equipment management and understood the cost‐risk propositions then began to follow a two‐step process : a) evaluating various alternatives in equipment selection based on both ownership and operating cost, and b) effecting the transaction based on the need‐demand situation (projects, work backlog, etc.) at the time of transaction.
5.1.1 Purchase price Purchase price – or capital investment – is the only factor that is known with certainty as it is defined when ownership begins. It is simply what you pay when you purchase the machine. As pointed out earlier, costs relating to purchase will affect the transaction process; for example, depending on whether you buy a machine with your own capital, buy it with financed capital, lease it or rent it, you will pay a different price. The only related costs to consider in addition to purchase price are delivery (freight), setup and installation, title/registration and any initial training. The freight cost will vary, depending upon the distance between the “stock yard” and the job site, and the weight to be transported. In some cases, machines can be larger than legal transportation limits and therefore must be transported in sections. This might lead to additional setup and installation cost. As a side note, the size of the machine (dimension and weight) may impact mobilization cost between sites. Legal transportation limits need to be considered in assessing this cost and should be accounted for in the equipment costing or job costing system. This cost will have an impact on equipment selection.
The other aspect to consider is that the cost of the tires/tracks needs to be deducted from the purchase price of the machine while calculating the ownership cost per hour. The main reason is that the tires/tracks are treated as operating cost and so should not be counted twice. Moreover, the life of the machine is different from that of the tires. Therefore, by leaving the cost of the tires in the calculation, we make an implicit assumption that when the machine is sold, it will be delivered with a new set of tires or tracks.
Page 12 TOTAL COST OF OWNERSHIP
Building on an example as we proceed, we can consider that we are buying an articulated hauler for the fleet. The cost of the hauler delivered to the site is $515,975. The cost of a set of tires is $37,400. Therefore, the purchase price excluding tires is $478,575. This is the value that will be used for calculating the ownership cost per hour.
5.1.2 Residual Value The residual value is the value that remains at the end of the ownership period. It is the value that is used to determine the capitalized amount or the equity to be recovered. The one issue about residual value that can be very deceptive is that it occurs in the future. Therefore, it cannot be treated in the same terms as the capital investment, which occurs in the present. E.g. an equipment salesman sets the price of an excavator at $10 million and then guarantees to buy it back from you for the same amount after four years. Therefore, from your viewpoint the residual value is $10 million. Does this mean that your capitalized amount is zero? Obviously, something is missing.
There is an interest cost associated with it: the cost of borrowing money. The interest on your $10 million is going to pay for the cost of the machine and more. Your cost of capitalization should be calculated by bringing the residual value from the future to the present using the appropriate discount factor. Therefore, when you calculate the ownership cost of a machine, it is always necessary to bring the future values to the present*.
The one other point to consider is the difference between fair market value (FMV) and guaranteed buy‐back value. FMV, as the name suggests, is the value that the market will pay for a piece of equipment. Auction results are the best indicator for this value. The guaranteed buy‐back value, on the other hand, is the wholesale value from an equipment retailer’s perspective. The equipment retailer is ready to pay this value, perform any necessary work on the machine and then take on the carrying cost until the machine is sold. There is a difference between these two values. Understanding it is vital to calculation of ownership cost. It is misleading to use the FMV in estimating the ownership cost and then expect the buyback number to be the same. You can use the FMV to obtain an estimate of the residual value. However if you intend the equipment retailer to buy the machine back from you, then you should use the buyback value. It is important to maintain a realistic balance between the evaluation and actual transaction processs. • The discussion on this subject, “Time Value of Money,” is beyond the scope of this material.
5.1.3 Depreciation cost Depreciation can be simply defined as the “decrease in value” of a product. If we know what we paid for a piece of equipment, and we have an idea as to what the equipment will fetch in the market after a period of time, then depreciation is the calculation by which we determine how we will recover this fall in value. There are three methods to calculate depreciation: market depreciation, book keeping based depreciation and tax laws based depreciation. The main difference between the methods is the basis for the residual value and the depreciation period.
In our example, the residual value of the hauler is expected to be $154,793 after five years. Therefore, if we determine the present value of this sum based on five years and 6% interest rate, it works out to $20,123. If the truck operates 2000 hours a year for five years, the depreciation cost per hour works out to $32.38. It is clear that as the interest rate becomes higher (like in some countries or markets) or if the ownership period is very long, the effect on present value becomes conspicuous.
Page 13 TOTAL COST OF OWNERSHIP
5.1.4 Depreciation time or ownership period The depreciation time is the duration used as the basis for calculating the ownership cost per hour. This period has a lot of influence on the equipment selection and transaction process. Understanding the depreciation time or the right ownership period requires some discussion on the operating costs and so, we will re‐visit this subject in a later section.
In the meantime, it is worthwhile to plant a few questions in the mind of the reader:
a. Is ownership period a function of the economics or more so the physical capability of the machine? In other words, is the economical life different from the physical life?
b. Are there any models which help us determine the economic life?
c. Does the expected life of components affect the ownership period?
d. Are there any legal statutory limits on the ownership period related to depreciation?
e. How does economic life affect TCO?
f. How does economic life affect operational decisions such as repair, rebuild, replace, retire?
5.1.5 Interest cost or cost of capital Two parameters are important when it comes to calculating the cost of capital:
a. The interest rate to be used.
b. The average annual value of the machine.
The interest rate depends on whether the machine is purchased with own capital or whether it is financed. When the owner’s own capital is used for purchasing the piece of equipment, then the rate used for calculating the cost of capital should at least be equal to a rate which can be expected from an equal investment. However, if the equipment is purchased with financing, then the rate used in the financing calculation should be used for calculating the cost of capital.
The average annual value (AAV) is simply the average between the first value: the purchase price, and the last value: the residual value. Assuming the purchase price of the machine is P, and the residual value at the end of its life (n years) is S, the average annual depreciation (d) can be expressed as d= (P‐S)/n. In other words, at the end of the first year, the machine has a value of P‐d, at the end of second year, its value is (P‐2d), and so forth. The average annual value of the machine can then be stated as (P+S)/2. This method uses several approximations. Financial methods exist which can calculate accurately the interest cost using the time of value of money concepts. For the purpose of the present discussion, it is sufficient to use this simple formula.
Page
Figu
In ofigupaympericostyieldimpo
5.1In adamequtax a
5.2Opetiresinvo
As sprev
Manmanpartbearprogsing
Appmos
e 14
ure 1: Illustra
our example re rather thment). The od is $335,3t of $20,123ds $10.06. Iortant to un
1.6 Insuralmost all cas
mage. Typicalipment. If thassociated w
2 Operaterating costs,s or tracks, olved and goo
stated beforeventive main
naging the anagement. Mtially correctring points grams can hle biggest im
lication affecst occasions,
ation of depr
of the artichan the oneresidual valu384. If we mu. If the hauln this case, derstand the
ance andses, a piece olly, the insurhe equipmenwith the piece
ing costs, the costs inground engaod decisions
e, operatingntenance pol
acceleration Most people t, it does noand so weahelp to monmpact on the
cts the wear, application
reciation and
ulated haulee without tue is $154,7ultiply this vaer is put to the interes
e implication
d machinof constructance for a pint is permittee of equipme
s ncurred as soaging tools, s must be ma
cost is affeicies.
of the increassociate in
ot present thar out over itor and redoperating co
r and tear of s impact ext
d calculation
er, the purctires becaus793. Therefoalue by the iwork for 20t cost is 31n of the inter
ne tax ion equipmeiece of equiped to run on ent.
oon as the mpreventive ade on a day
ected by fou
ease in operancreasing ophe total picttime. Howeduce this weost of the m
machines –ternal imple
n of average
hase price isse the interore the averanterest rate 000 hours a % of the derest cost as p
ent needs topment is calcpublic roads
machine is stamaintenancey‐to‐day basis
r factors: ag
ating cost isperating costure. Machinever, good oear and tearachine.
some jobs aements such
TOTAL
annual valu
s $515,975 (rest cost staage annual vof 6%, we geyear, the inepreciation cpart of the ov
o carry insuraculated bases, then there
arted, include, and repais if costs are
ge, applicatio
the big chat to age alones have mooperator carr. Operator
re easy and as tires and
L COST OF OW
ue
(we tend toarts with thvalue on a tet an annuanterest cost cost. Therefverall cost.
ance againstd on the vale could be a
e things sucir. A lot of me to be kept i
on, environm
allenge in eqone. Althougoving parts are and maincare could h
others are tod buckets m
WNERSHIP
use this he down two‐year l interest per hour ore, it is
t theft or ue of the machine
h as fuel, money is n line.
ment and
quipment gh this is and load ntenance have the
ough. On more that
Page 15 TOTAL COST OF OWNERSHIP
they do transmission and turbo charger. However, choosing the right machine for the application is, without doubt, the most important factor in reducing operating cost.
Environment cannot be controlled – we have to live with it. But although we cannot control it, we need to provide for it to keep the operating cost under control. When working in hot and dusty conditions, pre‐cleaners and secondary cooling kits must be installed. When working in abrasive environment, heavy duty components are required.
Finally, equipment policies which include maintenance and repair practices, operator care, walk around instructions and training are very important when managing operating costs.
Most equipment managers split total operating costs into four major categories: fuel consumption, wear parts (ground engaging tools and tires), preventive maintenance and repair. The best indicator for these categories is in past records. However, application, environment and age of machine are never the same in two instances. Therefore, it is important to understand the basis of these categories and manage them.
5.2.1 Fuel consumption Fuel consumption cost is a critical component of the operating cost. Traditionally, performance was the sole or primary criteria for engines. As the price of diesel increased fuel economy became a second primary criteria. Over the last two decades government regulation has added a third criteria, environmental impact, to the equation. Government regulations on emissions continue to tighten, and the price of diesel seems only to increase Therefore equipment manufacturers have a difficult task to develop new technologies to control and reduce fuel consumption and emissions without compromising performance. For example, load sensing hydraulics draws power only when required. The torque curves are being improved to provide torque rise at low RPM and hence reduce fuel consumption. Electronic control systems offer better gear shifting patterns. Having a driveline where the different components are matched and communicate with one another can have a favorable impact on fuel consumption.
In a situation of fluctuating oil prices, paying attention to the fuel consumption and its impact on overall cost is critical. In the articulated hauler example, let us assume that the fuel consumption is 21.2 liters per hour and that the cost of diesel is around $1.06/liter – this means $22.47/h. Comparing this with depreciation cost of $32.38, it works out to 69%.
The important conclusions from this discussion on fuel consumption are:
a. It is important to consider the cost‐benefit analysis of purchasing a higher priced machine which may have lower fuel consumption. In some cases, the saving in fuel cost can pay for the higher initial price within a year or two. This is the application of a TCO mindset.
b. Even between comparable machines, a difference in fuel consumption can lead to significant difference in operating cost and the total cost.
c. It is important to analyze the effect of changes in oil prices before making procurement decisions – this helps to understand the risk involved.
In some parts of the world, the cost of diesel is so high that the fuel consumption cost is actually greater than the depreciation cost. It is surprising to note that many companies do not keep track of fuel consumed per machine. Typically, the fuel truck makes a round on the job and fills up all the equipment. The total fuel consumed is then charged to the job. When data on fuel consumption is not tracked on a machine‐by‐machine basis, it becomes difficult to identify inefficiencies. Also, there is a school of thought which recommends that the preventive maintenance program be based on fuel consumed rather than clock hours. The reasoning behind this approach is that, if the machine consumes fuel, then it has to be working.
Page 16 TOTAL COST OF OWNERSHIP
5.2.2 Wear parts – ground engaging tools and tires As the name indicates, wear parts includes wear items such as bucket, teeth and segments, cutting edges, rippers, tracks, and tires. The life of these wear items are typically dependent on the environment and application. For example, an abrasive environment may lead to increased wear and tear compared to a normal one. The operator’s training level and commitment also impacts performance and life of the wear items. There are occasions when hauler tires with 1500 hours have no tread left on them. Engaging the 6x6 modes on flat and even surfaces only accelerates wear unnecessarily. Similarly, choosing the right type of bucket (and cutting edges) can help increase the life of the bucket.
5.2.3 Preventive maintenance Some of the synonyms for the word preventive are ‘precautionary’ and ‘protective’. Therefore, preventive maintenance for a piece of equipment can be viewed as an investment to protect the equipment rather than a necessary cost to run the machine. Many people in the industry believe that preventive maintenance of mobile equipment simply involves changing of oils, fluids and filters and lubricating pivot points on a regular basis. The truth is that while these are important segments of a properly planned and practiced preventive maintenance program, there are many additional elements that must be part of a successful program.
A generally accepted definition of preventive maintenance is:
The care and servicing by trained personnel of mobile equipment in satisfactory operating conditions by providing systematic inspections, and detecting and correcting potential failures either before they occur or before they develop into significant defects that may cause machine downtime and additional cost.
Detecting and correcting failures before they occur can mean that we may have to replace a component before it actually fails. In other words, the old adage gives way to a new mantra – “If it ain’t broke, change it anyway.” The worst thing about a downtime (due to repair) is the collateral damage caused by the breakdown. A $500 bearing can ruin a $7,000 transmission; a $100 hose can cause a $2,000 loss in production and idle the rest of the fleet. Collateral costs are extremely difficult to measure, as they do not appear in cost reports and are easily disregarded.
Equipment managers in the current world of mobile equipment must have skills that are equal to the technology of the machines that they will be supporting. It is not in the best interest of equipment managers, the company, or the machines themselves to have preventive maintenance carried out in a non‐regulated or non‐controlled way. Nor is it advisable that unqualified and non‐trained service personnel do maintenance of any kind on these types of machines. Equipment will continue to become more sophisticated; it will, therefore, require higher levels of skill and technology to continue to perform at all levels of maintenance.
Preventive maintenance is mandatory; companies must identify and define the policies, practices, procedures, measurements and systems that will provide the company owners the best machine availability, the lowest cost and the best return on their investment.
Page 17 TOTAL COST OF OWNERSHIP
5.2.4 Repair Repair is the action required to get a machine from a non‐operable state to an operable state. It is generally assumed that the machine is down during this state. Since repairs are visible and cause a disruption, this gets the attention of everyone on the job. Repairs can be classified as those that occur without prior indication – a sudden failure; and those that occur due to deterioration – aging failure. For example, a tire could fail suddenly when it hits a piece of rock or a sharp object. On other hand, the same tire could experience wear and become weak and fail over a period of time. Some of the “signs” of deterioration are easy to observe, especially for external components such as tires. On the other hand, detecting need of repair for a transmission or a turbo charger is more difficult. Modern technologies such as oil analysis and thermograph analysis help us to track deterioration levels.
Elimination of the repair involves replacing the failed component with a new one. Typically, the cost of doing the repair in an unplanned manner in the middle of a job is high. This is called an unscheduled failure resulting in unscheduled downtime. First, it involves troubleshooting, then obtaining the right parts and then fixing with minimal support equipment. Sudden repairs also pull mechanics from their routine work and hence are very disruptive. All the other equipment in the fleet also comes to a standstill.
On the other hand, the concept of repair before failure allows for a planned approach to maintaining the machine. A machine can be scheduled for repair over a weekend or during the night. Moreover, these repairs can be done in a workshop, which is a more controlled environment for the mechanics. Collateral damage (and related cost) is avoided. Downtime occurs but it is planned and less disruptive of operations. In a word, the repair is managed. Some managers estimate that on‐shift failures cost up to six times as much as planned repair.
Page 18 TOTAL COST OF OWNERSHIP
Having reviewed components of both ownership and operating costs, developed an understanding of these costs, their impact on our decisions and a concept of how to manage them, we will now increase our understanding of some of the cost categories and ways to estimate them.
6.1 Preventive maintenance cost The methodology to estimate preventive maintenance cost may vary depending upon the relevant organizations, applications, and practices. There are two types of practices: some equipment owners estimate the preventive maintenance cost on an hourly basis, while others use intervals (daily, 250 hr, 500 hr etc.). The hourly cost of preventive maintenance is inclusive of the interval basis and is the preferred method. However, the interval‐based method is useful from an invoicing/cash flow perspective, especially if the utilization of the machine is minimal.
Cost estimates can be grouped four ways: Material, Labor, Travel time & mileage, and Miscellaneous.
Material The items included under the heading of material are filters and lubricants (oils & grease). We can further group filters into engine filters (engine oil filter, bypass filter, fuel filter, extra fuel filters, air filter, coolant filter, safety air filter), transmission filters (trans filter, breather), drive axle filters (breathers), cab filters (ventilation filter, pre filter), and hydraulic filters (return filter, filter insert, ventilation filter). Each of these filters, in turn, has an interval for replacement. Therefore, the extended cost for particular preventive maintenance (for example 250 hr) can be calculated by multiplying the number of filters, cost of each filter and interval of replacement.
The other component of material cost is lubricants. A typical list of lubricants includes engine oil, transmission oil, hydraulic oil, axle oil, and engine coolant. The capacity of each housing mechanism (engine, transmission, etc.) can be obtained from manufacturer’s specifications. Therefore, the extended cost can be calculated based on the unit cost of lubricant multiplied by the capacity.
The cost of grease fittings is constantly changing. With new developments in machine design, the greasing requirements can vary. Additionally, with the rise of automatic greasing systems, it may be possible to estimate a machine’s grease consumption and thus cost. Without going into too much detail, it is not wrong to use a proportion of other material costs to estimate greasing costs.
Labor The items included under the heading of labor are both technical labor (mechanics) and non‐technical labor (helpers). Typically, there are established rates for the labor in an area. One rate may apply to preventive maintenance while a different rate prevails for more involved repair or shop work. In each case, the rate should include direct wages as well as any benefits which may be applicable.
The duration of work from a labor standpoint can be obtained from time guides provided by the manufacturer as well as from established practices in the company. It is important to be realistic rather than simply conservative.
Travel time and mileage This item of work is important, especially because preventive maintenance work occurs on the job site. This means that the mechanic needs to drive to the work shop on the job site and be paid for the time he spends in transit, although this does not produce quantifiable work. The cost of travel time and mileage is dependent on the number of visits to the site to perform
Page 19 TOTAL COST OF OWNERSHIP
actions. Some companies tend to keep the cost of lube truck/repair truck as an overall “cost of doing business” item. Others include it as part of labor charges, considering that these vehicles do not come for free. In the same manner, the amortized cost of the workshop and the carrying cost of parts inventory should be included in the calculation somewhere.
Miscellaneous There is one more item that typically falls in between the cracks: the cost for performing oil sampling and analysis. Although one can view this as either a preventive maintenance or a repair cost, it is important that the cost for this action is taken into account. Also, it may be advisable to set aside a small proportion of the cost for unforeseen actions.
6.2 Repair cost Estimating repair cost is the most challenging part of defining the operating cost. Repair cost is a function of several aspects including application, preventive maintenance program, operator training and care, and commitment. Therefore, we should consider some related concepts.
6.2.1 Measurements When it comes to repair, it is important to track two sets of measurements: interval between actions, and cost of action. It is possible that a machine might have few failures in it’s economic life, but the cost to repair each failure may be high. On the other hand, small but frequent failures could result in low reliability and high indirect cost. In a more technical world, these factors are referred to as mean time between failure (MTBF) and mean time to repair (MTTR). Reliability is directly related to MTBF, while availability is determined by the following equation:
MTBFMTBF + MTTR
Availability =
Some companies keep track of availability in terms of the calendar time, idle time, working time and down time. In that case, we can use a schematic structure shown below for defining availability.
Figure 2 : Defining availability in terms of planned time, uptime and downtime
Idle Time
Operating Time Repair TimePreventive Maintenance
Time
Total Calendar Time (Available)
Planned Time (Scheduled)
Uptime Downtime
Operating Time
(Planned Time ‐ PM Time)Availability =
The risk from an owner’s perspective can be related to reliability and availability. A low risk proposition should involve high reliability and high availability. Therefore, the key to understanding repairs is the COST‐RISK proposition. There is a clear balance between cost and risk. For example, a low risk option generally comes with a high cost. One could build an engine that lasts for 60,000 hours, but then the cost of such an engine (probably made of an exotic metal such as titanium) would be much higher. On the other hand, if one is ready to take some risk, the cost of repair can be lowered. One example of such an approach is to budget a cost of
Page
the the is fu
6.2Therclasscond
Opeoccushiftpracwe replintecan
FixemajoIn tirresappwheorgamilitthis com
Undcondany appthercomexpe
6.2Comavernot the we afailumay
On tis thcostlast to udesi
e 20
expected rebudget, thenutile to argue
2.2 Maintre are seversification incdition based
erate to failuurred, and tt failure can ctice when ttreat a lightace it basedrval betweeresult in cos
d time basor componethis case, thspective of roach is follen the operaanization. Fotary machineapproach i
mfort of low r
der conditiondition of thecorrective roach is a barmography, mponents. Thected life of
2.3 Compmponent life rage life of amean muchcalculation oalso have thure. In other y not fail at e
the other hahe life at whit, you budgemuch longeunderstand tres low risk,
pair; if the mn the surpluse for a low ris
tenance ral ways to ccludes: ope maintenanc
re, as the nahen making cost up to sihe criticalityt bulb. We r on the numn failures cast extremes b
sed maintenents on fixedhe componewhether it owed undertion is criticaor example, Fes, aircraft, is high, butrisk.
n based ma machine is aaction is palance betwand vibratihese analysemajor comp
ponent liis the basisny given com. The reasonof the averaghe data regarwords, the cnd of its aver
nd, most maich the chanet for a comr than the exthat this is a then it com
machine is ms could be shsk, low cost p
practiceclassify the mrate to failuce (CBM).
ame indicaterepairs so tix times as my of the operrun to a poi
mber of hoursan be long obut with high
nance replad time intervent is replahas failed. Tr circumstanal to the oveFTBM is usedetc. The cosbrings with
aintenance, assessed befperformed. Teen the OTFonal analyses become onents. The
fe s of budgetinmponent, but for the “lacge. Assume trding the lifechance of farage life. This
anufacturingce of failureponent basexpected life;a budgeting es with a hig
maintained whared betweproposition.
es maintenanceure (OTF), fi
es, entails runthat the macmuch as an oration is notint until it fs we have usor short. In th risk propos
aces vals. aced This nces erall d in st of h it
the fore This F and FTBM.sis provide particularly cost and risk
ng for repait the answerck of value” ithat we havee at which tilure is 50‐50s does not pr
g industries se is 20% or leed on its exp; in fact, it isprocess withgh cost.
well on the joen the equip
e practices aixed time b
nning the piechine is opeoff‐shift repat very importails before rsed the bulbhe world of sition.
. Modern tecgood informhandy whek of this app
ir cost. Mostr could be a n this informe 100 transmhey failed: t0, which mearovide us wit
state their exess. Thereforpected life. expected toh an embed
TOTAL
ob and the repment divisio
adopted by aased mainte
ece of machirable again. ir. It is possibtant. For exareplacing it; . Now, depecapital equi
chnologies, smation aboun the machroach is reas
t people typsingle numbemation lies inmissions that he average hans that the h useful info
xpected life ire, when youIn practice, o last longer.ded cost‐risk
L COST OF OW
epairs do noon and the p
an organizatenance (FTB
ine until a fa Additionallyble to followample, conswe don’t b
ending upon ipment, this
such as oil sut the condhine approasonable.
pically ask aer which man the statistict have failed has a 50% c transmissioormation.
n terms of tu calculate ththe compon. However, tk propositio
WNERSHIP
ot exceed project. It
tion. One BM), and
ailure has y, an on‐w the OTF ider how bother to luck, the practice
sampling, dition of ches the
bout the ay or may cs behind and that
chance of n may or
20 – that he repair nent may he key is n. If one
Page
Figu
6.2In thexpe
As foit is timeprov
e 21
ure 3 : Illustra
2.4 Calcuhe modern wected life, th
or the expeceasy to calcue period. It ivides a range
ation of com
lating reworld of sprehe cost of eac
ted life of a culate the freqs possible toe of scenarios
mponent life
epair costeadsheets it ch compone
component, quency with o simulate res. The next se
as a probab
t is possible tnt, and labo
a single detewhich compepair cost byection will co
bility
to list all ther required to
erministic vaonents are rey consideringonsider addit
TOTAL
componento replace it.
lue can be usequired to beg different cional details
L COST OF OW
ts in a machi
sed. Using the changed focomponent liof this subje
WNERSHIP
ine, their
his setup, or a given ives. This ect.
Page 22 TOTAL COST OF OWNERSHIP
Figure 4: Illustration of spreadsheet used for repair calculations
Evaluation Period (example)Beginning 0 hrs
Ending 10,000 hrs
Hrs Total Cost Unit Cost Total Cost
BRAKES
Accumulator 1 15,001 0 1.00 $0.00 $275.64 $0.00 $0.00
Accumulator 2 15,001 0 2.00 $0.00 $438.81 $0.00 $0.00
Solenoid Valve 1 12,001 0 0.50 $0.00 $277.79 $0.00 $0.00
Sealing Ring 2 8,001 1 0.00 $0.00 $43.63 $87.26 $87.26
Sealing Ring 2 8,001 1 0.00 $0.00 $45.79 $91.58 $91.58
Cprsn Spring 32 8,001 1 0.00 $0.00 $1.20 $38.40 $38.40
Press Monitor 1 5,001 1 1.50 $60.00 $214.57 $214.57 $274.57
Press Monitor 1 5,001 1 1.50 $60.00 $214.60 $214.60 $274.60
Footbreak Valve 1 15,001 0 2.00 $0.00 $830.24 $0.00 $0.00
Brake Plate 2 24,001 0 0.00 $0.00 $519.64 $0.00 $0.00
Brake Plate 2 24,001 0 0.00 $0.00 $519.64 $0.00 $0.00
Brake Piston 2 24,001 0 2.00 $0.00 $398.72 $0.00 $0.00
Brake Plate 2 24,001 0 0.00 $0.00 $274.90 $0.00 $0.00
TotalCost
OccurancesLabor Charges Parts
Component Qty Hrs
The discussion presented previously is for repairing and maintaining one machine. When we have a fleet of machines operating in one location, then the travel time and mileage need not be added to each machine. Further, the risk of failure can be allocated to the fleet rather than just one machine. For instance, the chance of a transmission failure at 14,000 hours may be around 60% for one machine. On the other hand, in a fleet of 10 machines, the chance of all the 10 transmissions failing at 14,000 hours is lower than 60%. Therefore, the cost budget on a machine basis can be lowered. It is important to understand this risk‐cost proposition, especially when outsourcing equipment maintenance.
Page 23 TOTAL COST OF OWNERSHIP
Four different models can help investigate the economic life or ownership period. Although not disconnected, they have appropriate merits and data requirements.
7.1 The Repair Reserve Model As the name implies, the Repair Reserve Model involves setting aside a reserve for repair works, drawing on the reserves when repair is required, and making a decision based on the reserve level. You can visualize this as an operating bank account for a piece of equipment or a fleet. As the machine starts to work, you deposit money into the account. This amount varies with the type, class, and size of the machine. Let us say, for example, that we deposit $5 every hour. After the first 2,000 hours, the bank account will contain $10,000. Let us assume that at 2,000 hours, you need to perform some repair work costing around $4,000. In this case, at the end of 2,000 hours, your bank balance would be $6,000. Thereafter you would continue to build on this reserve when the machine was put to work again.
This method produces an excess in the early hours which is used to cover normal increases in actual repair costs as the machine ages. It does not use purchase price, market value or other related factors. Therefore, it can be viewed as purely an internal method that requires only in‐house data.
Repair costs typically have two components, cost of action and interval between actions. Cost of action is the actual amount of money that needs to be invested on the machine. A major repair will produce a higher cost of action than a smaller one. However, if the interval of action is short, it will bleed the repair reserve account faster than the high cost actions. This method can monitor both cost of action and interval between actions.
There are some advantages and disadvantages for using this method. The advantages are that the method is very easy, requiring just one estimate and in‐house data. There is very little speculation, and calculation is fairly straightforward. On the other hand, by ignoring ownership related parameters, this method does not use any of the market related parameters. Therefore, the opportunities associated with market information are lost. It is also important to point out that the repair cost is a function of the preventive maintenance practice in the company. Therefore, this model justifies studying repair in isolation without preventive maintenance.
Page
HowdefiexammonadviresethenSompracappsomthe theythe on t
7.2The ownin thlowemaclimitof ato a to hecon
e 24
w can we mane certain rumple, if the nitoring the isable to seerve is arounn we can useme owners wctice and thalication) by
meone else’s next machiny can fix the best methodheir circums
2 The ClaClassical Co
nership cost he calculatioers the depchine life. Asts on their dll owning an low value (bhigh repair nomic life of
ake decisionules, which crepair reserreliability ofll the machd $10,000 ate a rule thatwill argue that they shouusing up thfleet when ine they buy.repairs usingd; each orgastance and o
assical Coost Minimizaper hour con of the deppreciation cos the machindurability andd operating balance betwcost). The lf the machine
ns based on can then be ve in the abthe machinine. For exat 10,000 hout suggests thhat they hald reap the be reserve. St is time for . Others willg the reservenization decutlook.
ost Minimtion Model mponent depreciation coost. Operatine starts to ad need to becosts, startsween owningowest pointe in which th
this methodused to monbove example. We can aample, if paurs, before mhat the macave built up benefit of coSome will arrepairs and note that te and then scides the bes
mizationconsiders bo
ecreases withost, we divideng cost, onage, all movie replaced. Ts at a high vag and operatt on the tohe total cost
d? Based onnitor the eque never goealso use this st records imajor repairshine can be the reserve
ontinuing to rgue that it then use thehe machine ell it. There st approach
Modeloth the ownh an increasee by the utilin the other ing and loadThe total cosalue (due to ting cost) betal cost curper hour is t
TOTAL
historical duipment ands above $4,0method to dndicate that start to brintraded at ae through aown the mais better to e reserve as may bring bis no single aat any given
nership and e in machinezation; as uthand, incre
d bearing parst of operatiohigh ownersfore rising torve identifiesthe lowest.
L COST OF OW
data, it is pod make decis000, then it determine wt the averagng the balancround 10,00a good mainachine (for seo get the maa down paybetter resaleanswer as ton point of tim
operating coe life. This istilization inceases with rts start to aon, which is ship cost), tho a higher vas the perio
WNERSHIP
ossible to sions. For is worth
when it is ge repair ce down, 00 hours. ntenance econdary achine in ment for e value if o which is me based
osts. The because reases, it a longer approach the sum en drops alue (due d of the
Page
Figu
Thisfacto
ThisopeFor will old relatassudecrmin
You In sonarr
7.3The ModTherthe startlife noteprodthe min
e 25
ure 5 : Illustra
s method useors. Therefo
s model canrations. Oneexample, it only cost $0machine witionship betumptions byrease and oimum cost p
can use thisome cases, trow. Timing o
3 CumulaCumulative del incorporrefore, if thepurchase prts out at 1 ris gradual. Te that there duce the lowlife of the imization an
ation of Clas
es both marre, it is impo
n be used e needs to bis not corre0.44/hr to opll actually ptween owniny assuming aoperating cospoint.
s model to hthe trough oof decisions
ative CosCost Model ates both oe purchase price is trackerather than 0The costs theexists only o
west total cosmachine is d cumulative
ssical Cost M
ket and macortant to und
for estimatie careful andct to assumeperate for throduce $0.1ng and operaa range of vsts increase
help in decisiof total costin the narrow
st Modelwas developwnership anprice of a pieed during its0. This curveen start to acone point in st; the costs its econome cost mode
Minimization
chine‐relatedderstand the
ing (lookingd not fall inte that a usehe next year12/hr when ating cost avalues and ldetermine
ion‐making bt curve is ratw‐trough cu
ped by Dr. Mnd operatingece of equips life. In othe is not lineaccelerate as a machine’sare higher bic life. A grl is presente
Model
d parametersassumption
g forward) oto the trap od machine pr. Nor it is losold after ond machine etting our kboth the m
by creating rther flat; in rve is import
Mitchell at Vig costs as a pment is $1, her words, thar. The increthe machinelife (on the
both below aaphical reprd below.
TOTAL
s, and involvs and data.
or analyzingof making mpurchased atogical to assuone year! Thage require
knowledge oagnitude an
rules which dother cases tant
rginia Tech. function of then the rehe cost curvase in cost ie ages. The inon‐linear cnd above thresentation
L COST OF OW
ves several j
g on‐going isleading judt five years oume that a fhe complexites that we cof how ownnd the timin
draw your athe trough
The Cumulaf the purchaepair cost in ve shown in n the early simportant pcost curve) wis point. Thisof the class
WNERSHIP
udgment
(current) dgments. of its life four year ty of the heck our ing costs ng of the
ttention. is rather
tive Cost se price. terms of Figure 5 stages of oint is to which will s point in sical cost
Page
Figu
As mcostcostdepe
The makdepecarespencostecon
ResetypetworepaconvscierepaexpeAnofleetcom
e 26
ure 6 : Classic
mentioned ets, or speed ts, or the mendent on si
more critickes it unbeaendent of the. As you cand in keepint is the biggnomic life ba
earch done aes, classes, si. In other woairs before ventional wntific foundaair cost of $1ected to havther way oft longer befo
mes to selecti
cal Cost Min
earlier, the cof costs, an
money that ize/class of m
al componearable to hohe equipmenn see, any ong the machest challengased on the a
at Virginia Tizes ranging ords, if the pthey replac
wisdom usedations of this1 was differeve a shortef looking at tore it is econing machines
imization an
cumulative cnd acceleratineeds to bemachine and
nt is the acold on to thnt design phiof these factine working ge for equipmacceleration
ech showedfrom dozerspurchase pried the macd by expers method. It ent for differr economic this observanomical to res.
nd Cumulativ
cost curve coion of costs.e spent now type of app
cceleration ohe machinelosophy, pretors will detin its later ment managof cost.
d that the cus, scrapers, ace was $1, tchine. This rienced equis also intererent machinelife compar
ation is that eplace them
ve Cost Mod
onsists of tw. As a machiw, will startlication and
of costs. This in your fleeventive maitermine the stages of lifegers. In fact,
mulative corticulated hahen equipmis an imporipment maesting to notes; smaller mred to biggebigger mach. This is a ke
TOTAL
dels
wo componeine is put to to rise. Thenvironmen
s acceleratioeet. The accntenance pramount of e. Managing, it is possib
st spent on aulers, excavent owners rtant observnagers, thee that the lifmachines (wier machines hines are rey decision m
L COST OF OW
ents: the inco work, the he speed ofnt.
on is the facceleration orogram, and money that g this acceleble to determ
a machine (vators etc) wspent anothvation, as itereby validafe corresponith lower cos(with highequired to be
making factor
WNERSHIP
crease in speed of costs is
ctor that f cost is operator you will ration of mine the
different was about her $1 on t reflects ting the ding to a sts) were er costs). e kept in r when it
Page 27 TOTAL COST OF OWNERSHIP
7.4 The Component Life Based Model Although component life is an implicit assumption in the calculation of repair cost and hence a part of all the models described earlier, this model helps us to understand a very important aspect of equipment management: the relationship between cost and risk. This method uses an estimate of component life (of major components), frequency of action required, and the cost of action to fix the components. Although this method can be used for both estimating and managing ongoing costs, its relevance is more pronounced in the estimating stage.
Average component life is rather useless in calculating the repair costs. For example, if one weatherman states that the chance of rain is 20% and another one says 50%, which weatherman is giving you useful information? Most people would immediate choose the 50%, as it is a higher number (thinking that they are taking a conservative approach). Let us take a step back for a moment and think: what does 50% chance of rain mean? It means that it may rain or not. One does not need to rely on supercomputers, satellites, or any other technical gadgets to make such a profound statement. You could do that lying in bed. In the same vein, the average life of a component, say a transmission, does not provide any useful information. An average life of 10,000 hours really states that some of the transmissions will fail before 10,000 hours and others will fail afterwards. But this does not provide you with any useful information. Therefore, we refer to the use of expected life, which in most cases in the industry refers to t20 or B20, or the chance that 20% or fewer of the population of the components will fail at a given life or less. It is important to know the likelihood of failure, especially for critical operations.
The deterministic approach uses a single point estimate for component life. In other words, the life of the component is a single value. Based on this assumption, we can construct a worksheet that includes the name of the component, the number of components in the machine, and the expected life. The frequency of action within a given time window can be calculated by dividing the time window by the component life. The cost of action can be calculated using the price of the component and the labor cost required to perform the action. By adding these costs for all components, it is possible to arrive at the repair costs. You can then use the observation from the research at Virginia Tech to arrive at the economic life by comparing the repair cost and purchase price of the piece of equipment.
The likelihood of failure (probability) approach uses an instance of life based on pre‐defined parameters. This approach requires the simulation of multiple instances with different component lives based on the pre‐defined distribution. For example, if we know that the chance of failure of a transmission around 8,000 hours is 20%, around 12,000 hours is 50% and around 18,000 hours is 90%, then we can construct a distribution (which is often a bell shaped curve). Using this data in a simulation, it is possible that the repair costs can be as high as $20/h (when a component life of 8,000 hours is used) and low as $10/h (when a component life of 18,000 hours is used). Warranty information can also be incorporated in the distribution by stating that the chance of failure, at for example less than 2,000 hours, is zero. Let us look at the result of 1,000 simulations for a piece of equipment.
Page
Figu
The fleetscencurvIn o(dowemeon acostaffeseco
e 28
ure 7: Illustra
inferences ot can be anynario, while ved representher words, wntime, lossergency laboany risk, repat‐risk proposcts the econondary life ar
ation of repa
one draw froywhere from the higher
nts the cumuif the equip of productior etc.). On thair costs will sition is impnomic life anre important
air cost when
om this exer$13/hr to $side repres
ulative occurpment user (on, etc.), thehe other hanbe high (incortant, consnd purchase t, the compo
n using likeli
rcise are tha25/hr (see asents an unrrences of th(say a projecen the cost ond, if the opecluding hiringsidering that decision. Wonent life mo
ihood appro
t the repair bove). The lnfavorable sche cost, it cact, operationof repairs caneration is critg replacement this affectsWhen compoodel become
TOTAL
ach for com
cost for anyower side recenario. Althn also be vien etc.) is willn be low (notical and it isnt machines)s the repair onent life, cos helpful.
L COST OF OW
mponent life
y one machinepresents a fhough the ewed as the ling to shareo need to stos not possibl). Understancost, which,ost of rebuil
WNERSHIP
ne in the favorable s‐shaped risk line. e the risk ock parts, e to take nding this , in turn, d and/or
Page 29 TOTAL COST OF OWNERSHIP
Now let us try to apply the subject that we have discussed so far and create a simple spread‐sheet to estimate the owning and operating cost.
a. The purchase price of the machine; including all options, delivery and set‐up costs.
b. The purchase price without tires/tracks (calculated); the cost of the tires is included in the operating cost and, therefore, removed from the owning side. Leaving the cost of the tires/tracks in the purchase price would relate to selling the machine with a new set of tires or tracks.
c. Depreciation time or ownership period is the economical life of the machine in the fleet.
d. Residual value is expected fair market value at the end of the intended life. As explained earlier, this is a future cost and, therefore, must be treated in terms of net present value.
e. Annual depreciation cost (calculated) based on purchase price, residual value, and depreciation time.
f. Interest rate to be used in calculating the cost of capital.
g. Calculation of interest cost based on average annual value.
h. Machine tax (if any).
i. Insurance cost: on an annual basis.
j. Fuel cost per volume. It is difficult to estimate the cost of diesel over the life of the machine; as a starting point, the present cost of fuel can be used. The sensitivity of fuel cost towards the total cost can be studied after setting up the spreadsheet.
k. Fuel consumption per hour; this is based on application, environment, operator efficiency, and machine design.
l. The preventive maintenance cost; this should include material, labor, travel time and mileage.
m. Interval in hours corresponding to cost as stated above (l). n. Replacement cost of a set of tires/tracks.
o. Lifetime for a set of replacement tires/tracks for the given application.
p. Repair cost for the intended life. This is calculated by setting up a separate spreadsheet for the components, their lives, parts, and labor cost.
q. Operator cost on an annual basis; this can be omitted if only the machine cost is desired.
r. Expected utilization in terms of working hours in a year (this will impact the economical life, repair cost).
Various cost categories under owning and operating cost can be calculated as shown in the example. This method gives a simple way to estimate the ownership and operating cost. The total ownership and operating cost (without the operator cost) can be defined as the internal recovery rate that, when paid for, accounts for the fall in value as well as the ability to operate the machine during its intended life.
Page 30 TOTAL COST OF OWNERSHIP
Table 3: An example of ownership and operating cost calculations
Machine Model Item Units Costs
A Purchase price 515,975$ B Purchase price, excluding Tires / Tracks 478,575$ C Depreciation time years 5.0D Residual value 154,793$ E Depreciation cost ((B‐D)/C) per year 64,757$ F Interest % 6.0%G Interest cost (F x (A+D)/2) per year 20,123$ H Machine tax per year excl.I Insurance per year 9,774$ J Fuel Cost per liter 1.06$ K Fuel Consumption Rate (Medium Duty Cycle) liter/hour 21.2L PM Cost (per visit) per visit 800$ M PM Interval hours 500N Cost of Tires / Tracks per set 37,400$ O Lifetime of Tires / Tracks hours 5,000P Repairs and Maintenance (RMC) per year 13,320$ Q Operator Cost per year excl.R Operating Hours per year 2,000
Note: In most cases, Preventive Maintenance cost is included in (P) repair and maintenance.
Machine ModelX Owning Cost per Hour
Depreciation (E/R) 32.38$ Interest (G/R) 10.06$ Machine Tax (H/R) excl.Insurance (I/R) 4.89$
X1 TOTAL FIXED COST PER HOUR 47.33$ Y Operating Cost per Hour
Fuel (J x K) 22.47$ Oil, Grease, & Filters (L/M) 1.60$ Tires / Tracks (N/O) 7.48$ Repair & Maintenance (P/R) 6.66$
Y1 TOTAL VARIABLE COST PER HOUR 38.21$ Z Operator Cost per Hour (Q/R) excl.
TOTAL COST PER HOUR (X1+Y1+Z)) 85.54$ It is interesting to study the impact of certain variables once the spreadsheet is set up. For example, assume that the price of diesel were to go up to $1.35 per liter. What happens? The fuel cost per hour now goes up to $28.62 per hour, impacting the total cost by $6.15 per hour. Similarly, one can study the impact of residual value, repair cost, and ownership period on the total cost of ownership.
Page 31 TOTAL COST OF OWNERSHIP
The reason we spend so much time and effort in understanding the various concepts in total cost of ownership is to be able to make good decisions. This is a step‐by‐step process.
The first step is data collection – because without data, we will spend too much time relying on our ‘gut feelings’. The second step is analysis – converting data into information. We can have lots of data but if it is not converted into practical information, it becomes useless. The third step is knowledge development – here we look for patterns in the analysis, a cause‐and‐effect relationship, trend etc. to develop insights into the operation. The final step is enlightenment – where we use several experiences and the knowledge gained through analysis to develop rules to manage our equipment. The rules can sometimes be in the form of policies, threshold limits, timely review and action etc. In fact this process can be applied to any type of business operation. In the equipment world, we sometimes skip steps and make decisions based on our instinct or experience. Although this might lead to successful decisions, in the long term it fails to beat the odds. Therefore, decisions are best made based on facts rather than judgment.
9.1 Buy, Rent or Lease? The decision to a buy a piece of equipment stems from the fact that you believe that you can earn a better return from the investment than from other alternatives. The decision to buy can be broken down further into whether you want to buy with your own money or borrow it. This decision should be based on the condition that the money the equipment generates is greater than if the money had been invested elsewhere (the ‘opportunity cost’). The money the equipment makes can come from direct sources (such as renting it out) or indirect sources (such as work done by the machine – material excavated by the excavator).
The cost of capital (interest) should be included as part of the ownership cost, as it defines the opportunity cost of money if it were invested elsewhere. This becomes clear in the case of borrowed money – the equipment should pay for the interest on the borrowed money as well as create earnings for its owner.
The difference in the two options is the risk factor. When you pay with your own money, then you must consider the timing of the investment as well as its cash flow.
The decision to rent depends on the size of the work backlog and the rental rate including the number of hours. Rental is very much a short term solution, when there is uncertainty about workload. For example, if you have a six month work backlog, then it may not be prudent to buy a piece of equipment.
In order to compare the rental rate, we can use the previously used example of the articulated hauler. The owning and operating cost of the articulated hauler is $52.58. Supposing the rental rate for an equivalent hauler is $10,000 per month. Given that the number of hours allowed under a rental contract is typically about 200 hours, this works out to $50.00 per hour. Additionally, the rental contract would specify that the user is responsible for daily preventive maintenance work and fuel with a requirement on balance tire life. Thus if we add these costs to the rental rate it works out to $62.00 (assuming that the tire cost need not be included at this time). This is the total cost per hour that must be used to compare if the same machine were to be purchased by the user. The reason that the rental rate is higher than buying is that a rental company bears the risk of utilization (the machine may not rent out every month of the year) as well as the risk of repair (of the machine after it comes back from rent). In addition, a rental company must include a return on investment when calculating the rental rate.
Page 32 TOTAL COST OF OWNERSHIP
The leasing solution is like a long term rental, the difference being that with leasing the contract stipulates a time period, a total limit on hours (not per individual month), and an optional buy‐out price. The user of the machine has the incentive to maintain the machine if the buy‐out clause is exercised.
In most cases, the user would like to purchase the machine but does not have the money to pay for a new one. He is also interested in positive cash flow, especially in the beginning of the project. Therefore, leasing allows the user to establish the project by paying monthly fees with the option of buying the machine at a later date and at an affordable price.
From a leasing company perspective, the monthly fees and the residual value are important. If the leasing company were to set a low residual value on the machine, then the monthly rate would not be competitive. Similarly, if the residual value was set at an artificially high level, the monthly rate could be low but stand the risk of the renter not buying the machine, or of a loss if the leasing company had to sell it on the second hand market.
9.2 In‐house vs. outsourced repair & maintenance When the repair and maintenance of a machine is outsourced, the company involved (typically a dealer) will be able to provide a good estimate on an hourly basis. Now, if we were to develop an estimate for in‐house repair, we must consider the following:
1. The consumables delivered at the site.
2. The full burden rate for the labor (including benefits, coverage etc.).
3. A good budget for the major components based on the usage.
4. A cost for the facilities.
In addition to these, there are other “soft” issues that need to be considered:
a) The ability to maintain and repair different makes of machines.
b) The training required to keep up to date with technology.
c) The ability to stock parts of different makes.
d) The risk of downtime.
When repair and maintenance are outsourced, the dealer is likely to include travel time and mileage, as the mechanic will spend considerable time traveling to the site. Therefore, it would be prudent to have all the machines serviced in one visit. However, the same is not the case with repairs – they aren’t all required at the same time. Finally, risk management with a fleet of equipment is important. As pointed out previously, when we develop the repair cost of one machine, we will budget for a major component based on its expected life. However, if there is a fleet of similar machines, then it is not necessary to budget for the same component for all machines (of course, this is dependent on the machine hours and likelihood of failure). Therefore, the outsourced repair cost for one machine will be higher than the average repair cost of a fleet of similar machines.
Page 33 TOTAL COST OF OWNERSHIP
Below is a list of questions to ponder in relation to equipment costs.
1. What is the process involved in selecting machine requirements for a particular operation (site, plant)?
2. How do you arrive at the ownership period in the RFP / RFQ / tender?
3. What assessment model do you use in selecting manufacturer, make, and model?
4. What are the most important parameters regarding purchase of a piece of equipment?
5. How do you decide whether you want to purchase/lease or rent equipment?
6. How do you determine fleet, productivity, and cost of machines required for a particular job site?
7. How do you view fixed guaranteed repair and maintenance cost from the dealer vs. in‐house maintenance?
8. In the maintenance of a piece of equipment, there are two elements – risk and cost. Which is more important to you and why?
9. What sort of data do you keep for your equipment (repair, maintenance, fuel, etc.)?
10. Typically, what are the most important inputs and outputs of a job study?
11. What is the relation between bank density and loose density?
12. If an excavator bucket is rated as a 4 m3 bucket, can it hold 4 m3 of water? If no, will it hold more or less?
13. What is meant by bucket fill factor? What is the assumption on the heap (slope) of the material for an excavator bucket and a loader bucket?
14. When we talk of material we mention 2:1 slope. When we talk of haul roads we mention 5% slope. What is the relationship between the two approaches?
15. What is meant by excavation class and how does it impact the bucket fill factor?
16. How is 50 min/hr rating different from long‐term mechanical availability and utilization?
17. How does one determine the best match between a loading unit and a hauler (any rules of thumb)?
18. How will you determine which is the best size bucket for a loading unit?
19. What are the components of a cycle for a wheel loader operation?
20. What factors affect the cycle time of an excavator?
21. What are the principal parameters defining a haul road?
22. What is meant by ground structure and how does it impact a hauler cycle time?
23. What is the rule of thumb to calculate the number of haulers required for a particular haul?
24. Does the type of material and transport surface impact the fuel consumption of the excavator and the wheel loader?
25. What is the difference between the loading strategy full buckets and full hauler?
Page 34 TOTAL COST OF OWNERSHIP
Templates are provided which may be useful for calculation of a project TCO.
Appendix 1 – Ownership and Operating Cost Template This can be used to calculate the total cost/hour of a given machine, by combining the fixed (ownership) costs with variable (operating) costs.
Appendix 2 – Loading Production Estimator Template This can be used to estimate the production capacity for a given loading tool when presented with an “unlimited” number of haulers to fill. Production rate is expressed as tons/hour or a quantity of trucks that can be loaded within an hour.
The template is set up for an excavator but with minor modification can apply to wheel loaders as well. This is just one example: Alternative calculation methods are available to estimate production capacity of loaders or haulers on a fleet basis.
Appendix 3 – TCO: Total Cost of Ownership Template TCO is the combination of fleet performance or production with the hourly cost calculation related to the fleet operation. It is not sufficient to look only at the hourly cost or production. They go together to derive the cost of work performed, i.e. cost per transported unit. Such a calculation can guide different conclusions:
Machine purchase. By comparing alternative machine types, it is possible to choose the most suitable machines for carrying out the work.
Machine distribution. A large contractor may have several different machine types or sizes, and different types of work to complete. By suitable calculation he can decide which machines should be placed on which jobs so the total cost of the job can be reduced to a minimum.
Cost forecast. Before starting a job it is desirable to calculate how much it will cost, as it may form the basis for a bid.
Whatever the purpose, the calculation process is the same: 1‐ Calculate hourly cost, 2‐ Calculate hourly production, and 3‐ Combine (1) and (2) to arrive at a unit cost for the work to be performed.
Sometimes extenuating factors may require a certain combination of machines even though it is not the lowest cost solution for the project. Such factors are outside the calculation of TCO and should be considered at a different stage of project evaluation.
Page 35 TOTAL COST OF OWNERSHIP
Appendix 1 – Ownership & Operating Cost Template DATA INPUT FORM ‐ duplicate for each machine under consideration
Machine Model ___________________
Item Units Costs Comments
A Purchase price enter initial machine value
B Purchase price, excl. Tires / Tracks (A‐N) net initial machine value
C Depreciation time years period under consideration
D Residual value choose a preferred formula
E Depreciation cost ((B‐D)/C) per year
F Interest % enter annual cost of money
G Interest cost (F x (A+D)/2) per year
H Machine tax per year enter if applicable
I Insurance per year enter if applicable
J Fuel Cost per liter enter unit cost of diesel
K Fuel Consumption Rate liter/hour specific to each machine
L PM Cost (per visit) ** per visit enter consumables
M PM Interval hours enter scheduled interval
N Cost of Tires / Tracks per set enter replacement cost
O Lifetime of Tires / Tracks hours application dependent
P Repairs and Maintenance (RMC) per year
Q Operator Cost per year enter cost of the operator
R Operating Hours per year enter schedules hours
** Note: In many cases, Preventive Maintenance cost is included in (P) repair and maintenance.
CALCULATION FORM ‐ base on data input listed above
Machine Model ___________________ Comments
X Owning Cost per Hour
Depreciation (E/R)
Interest (G/R) if applicable
Machine Tax (H/R) if applicable
Insurance (I/R) if applicable
X1 TOTAL FIXED COST PER HOUR total ownership cost/hour
Y Operating Cost per Hour
Fuel (J x K)
Oil, Grease, & Filters (L/M)
Tires / Tracks (N/O)
Repair & Maintenance (P/R)
Y1 TOTAL VARIABLE COST PER HOUR total operating cost/hour
Z Operator Cost per Hour (Q/R) if applicable
TOTAL COST PER HOUR (X1+Y1+Z)) total O&O cost/hour
Page 36 TOTAL COST OF OWNERSHIP
Appendix 2 – Loading Production Estimator Template
User Date Jobsite
Loaded Material Properties Ref
Material Density (Banked) A kg/m3
Material Swell Factor B %Material Density (Loose) C = A/(1+B) kg/m3
Material Class
ModelRated Bucket Capacity D m3
Average Bucket Fil l Factor E %Average Bucket Volume / Pass F = D x E m3
Average Swing Angle (if appl.) G degreesAverage Cycle Time / Pass H secBench, Working Height I m
Volume Vexc = (3600 / H) x F x T m3/hrWeight Pexc = Vexc x C ton/hr
ModelPayload Capacity, Rated J tonsVolume Capacity, Heaped K m3
Calculated Bucket Passes L1 = J / (F x C / 1000) passesWhole Bucket Passes L = round (L1) % of ratedPayload per Truck M = F x C x L / 1000 tons 0%Volume per Truck N = F x L m3
0%
Quick 1st Pass Load O secTime for Other Passes P = ((L)‐1) x H) secTruck Spotting Time Q secTotal Truck Load Time R = O + P + Q sec min
Operating Efficiency S % min/hrExcavator Availability T %Effective Util isation U %Trucks per Operating Hour V = ((3600 x S / R) xT) xUEstimated Hourly Production X = round( V ) x M x U ton/hr bcm/hr
KeyData to inputData to calculate using formulas
Description
NOTE: The above figures assume "unlimited" truck presentation. Excavator delays waiting for trucks are not taken
Loading Unit
Loading Unit ‐ Hourly Production Estimate
Hauling Unit
Loading Style
these production levels will be achieved in practice.
Hauler Loading Time
Estimated Maximum Hourly Production
NOTE: Production figures indicated above are estimates only. No guarantee is given or implied that into account and will, if incurred, reduce total production.
Page 37 TOTAL COST OF OWNERSHIP
Appendix 3 – TCO: Total Cost of Ownership Template
TCO TEMPLATE ‐ duplicate form for each machine combination consideration
Project Outline
A Production Target or Goal
B Timeframe or Limit (if any)
Loader(s) Hauler(s)
Item Units Fleet Total
C Quantity of machines in fleet
D Fleet Production rate
E Cost per hour
F Cost per unit production E / D
G Total Cost F x A
H Project duration, work hours A / D
Guidance:
A‐ Enter the production goal, typically a quantity of tons, bank cubic meters, or loose cubic meters.
B‐ Enter the timeframe in which to complete the project (if any), typically days/months/years.
C‐ Enter the number of machines (loaders and haulers) to be considered in the project.
D‐ Enter the production rate derived for the fleet, typically tons/hour, bcm/hour, or similar. (see Appendix 2, for example template).
E‐ Enter the cost/ hour derived for each machine type, typically $/hour or similar. (see Appendix 1, for example template).
F‐ Calculate the cost/unit production, line E / line D, typically $/ton, $/bcm or similar.
G‐ Calculate the total cost for the project, line F x line A, typically $ or similar.
H‐ Calculate the project duration, line A / line D, for the machine combination and compare to line B.
When evaluating multiple machine combination scenarios, the results in lines G and H are used to find the most cost effective within the appropriate timeframe.
Page
The formadvi(VirgConslongspeccusthavemind
Auth
The
Dr. Gwithpresas waccoand this calle
Dr. Kin MSingColletwo
EndoVolvoWritt
Liabilthe rany wto thlimita
e 38
original mams of inputs ice providedginia Tech) struction Equg list in itself,cial mention.tomers and ie shaped thed, a special t
hor biograph
original mat
GOVINDAN Khin Volvo Grsent role, Dr.well as Globalounts aroundoperations massignment,ed Volvo Con
Kannan receiMay 1999. Hegapore in 19ege, India in years. His em
orsement. The vo Construction ten permission
lity. Volvo CE aresults containewarranties of me entity that usation, lost reven
terial contaiand discuss
d by Dr. Micis greatly uipment can the discussi. Finally, Volvnputs, queste author’s thhanks.
hy
terial contain
KANNAN worroup North A. Kannan wasl Key Accound the world. managers in he was invonstruction Eq
ived his Ph.De received a995 and a B1991. He hamail address
views and opiniEquipment (Vois required from
and the author ed herein, or thmerchantability ses this documenues or profits.
ned in this sions within chael Vorsteappreciated.not be over ons and insigvo Constructions, suggesthoughts over
ned in this do
rks as the SeAmerica, a gs Vice Presidet Manager wDr. Kannan defining variolved in the duipment Site
D. degree fromMasters Deachelors Degas also workeis govi.kanna
ions of author eolvo CE) and them Volvo CE and
hereby disclaimhe appropriatenor fitness for aent for any indi
document wVolvo CE as
er of Virginia. The contremphasized.ghts providedtion Equipmetions and adr a period o
ocument wa
nior Vice Preglobal manuent North Eawhere he wasworked withous elementdevelopmente Simulation.
m the Via Deegree in Civilgree in Civiled as a site ean@volvo.co
expressed in thiey may not be ud the author for
m any and all eness of exampla particular purirect, incidenta
was developes well as oua Polytechniribution mad. Although nad by Randy Bent regularlydvice from mf years – to
s authored b
esident of Strufacturer of ast Asia withis involved wih the procurets of total cost of an earth
epartment of Engineering Engineeringengineer for om.
is document doused for advertr any form of rep
express or impliles used in the rpose. In no evel, consequentia
TOTAL
ed through rtside expertic Institute ade by indivaming individBushelli and Jy presents seany participaall those wh
by Dr. Govind
rategy and Butransport soin Volvo Conith the manaement speciast of ownershmoving oper
f Civil Engineg from the Ng from the RLarsen & To
o not necessariltising or producproduction.
ied warranties document incluent shall Volvo Cal, or special da
L COST OF OW
research andts. The guidaand State Uviduals withduals could bJim Leroy areeminars to gating industrho have sha
dan Kannan.
usiness Deveolutions. Prionstruction Eqagement of laalists, fleet mhip (TCO). Prrations mode
eering at VirgNational UnivRegional Engoubro Ltd. in
ly state or reflect endorsement
regarding this uding, without CE or the authoamages, includi
WNERSHIP
d various ance and University in Volvo become a e worth a lobal key ry players red their
elopment or to his uipment, arge fleet managers evious to eling tool
ginia Tech versity of gineering India for
ect those of t purposes.
document, limitation, or be liable ng without