Transcript of Torque. Correlation between Linear Momentum and Angular Momentum Resistance to change in motion:...
- Slide 1
- Torque
- Slide 2
- Correlation between Linear Momentum and Angular Momentum
Resistance to change in motion: Linear behavior: Inertia Units M
(mass), in kg Angular Rotational Inerita, Symbol I aka Moment of
Inertia Has to do with more than just mass, it includes the shape
of the object. If x cm is far away, I is bigger. Based on mass and
mass distribution.
- Slide 3
- Three Important equations for I : Thin Walled Cylinder I = MR 2
(also valid for an orbiting body) Solid Cylinder I = (1/2)MR 2
(easier because the mass is not so far away) Sphere I = (2/5)MR 2
(marble)
- Slide 4
- Slide 5
- Cause of acceleration Linear Force (Newtons) Angular Torque (
Nm)
- Slide 6
- Momentum Linear p = mv ( units kgm/s) Angular L = I (units kgm
2 /s) Bigger mass = harder to stop Faster moving = harder to
stop
- Slide 7
- Kinetic Energy Linear K = (1/2) mv 2 (Units Joules) Angular K R
= (1/2) I 2 A rolling ball has translational and rotational Kinetic
energy. Remember: ms become Is, vs become s
- Slide 8
- Pivoting Object Take a shape and a piece of paper. Label an x-y
axis on the paper. Label pivot point on the shape. Place at origin.
Label x cm on shape. Draw weight vector. Draw position vector r
from pivot to x cm. Move position vector from origin to x cm.
- Slide 9
- Definition: torque Torque is the cause of angular acceleration
in the same way that force is the cause of linear acceleration.
Symbol (pronounced tao) is the cross product between r and F We say
= r cross F = r x F
- Slide 10
- Relationship between torque and Newtons second law F = ma rF =
rma a is tangential, so a =r rF = torque, = rmr = mr 2 = I ( I=m 1
r 1 2 = m 2 r 2 2 ) So = I ( must be in rad/s 2 )
- Slide 11
- Back to picture Draw the angle between the FIRST r vector that
starts at the pivot point and the F vector. Then draw the angle
between the moved r vector and F. The moved vector is 180-. The old
r vector was at . = rF g sin(180-) Mathematically, sin(180-) = sin
So = rF g sin() in magnitude. Use RHR for direction.
- Slide 12
- On picture, Split weight vector out into components mgcos
points toward pivot, mgsin points perpendicular to make it rotate.
mgcos gets cancelled out, thats why we use the sin component, =
rFsin() That component in this case is spinning it cw, or in the
negative direction.
- Slide 13
- Lever arm Draw a line from pivot point across to weight vector
so that is crosses weight vector at 90 degrees. That line has a
magnitude of rsin This is very important. It has a special
definition. Its called a lever arm (symbol l ) We can say: = l
F
- Slide 14
- Cross Product Guided Practice #1 P = 4i + 2j k Q = -3i + 6j -2k
P x Q = Answer: 2i + 11j + 30k
- Slide 15
- Guided Practice #2 Cross Products P = 2.12i + 8.15j 4.28k N and
Q = 2.29i -8.93j 10.5k m Find P x Q Answer: -124i +12.5j 37.6k
- Slide 16
- Slide 17
- Solution 1) O = 0.17 rad/s (v/r) 2) I = (2/5)MR 2 = 0.0144 kgm
2 3) = 1735 rad/s 4) = use quadratic to find time 5) t = 4.25
s
- Slide 18
- Slide 19
- Solution Find I I = MR 2 =.625 kgm 2 Find = 16 rad/s Find = =
800 rad = 127 rev
- Slide 20
- Slide 21
- Slide 22
- Slide 23
- Slide 24
- Slide 25
- Slide 26
- Slide 27
- Slide 28
- Slide 29
- Slide 30
- Slide 31
- Slide 32
- Slide 33
- Slide 34
- Slide 35
- Slide 36
- Slide 37
- Slide 38
- Slide 39
- Slide 40
- Slide 41
- Slide 42
- Slide 43
- Slide 44
- Slide 45
- Slide 46
- end https://www.youtube.com/watch?v=GLlpi- 0_lB0
https://www.youtube.com/watch?v=GLlpi- 0_lB0